X-Git-Url: http://git.ipfire.org/?a=blobdiff_plain;f=README;h=ef8d437fbd46bf350eb6b259eeed3dd0a1810276;hb=6b75d35949968ea2083d5778de6882e175ecc3d0;hp=a52ff46c213d9afe4fa9b624679582f319515b61;hpb=7c0e5d865ff0b86dfce492b656238919c659d756;p=people%2Fms%2Fu-boot.git diff --git a/README b/README index a52ff46c21..ef8d437fbd 100644 --- a/README +++ b/README @@ -681,8 +681,10 @@ The following options need to be configured: CONFIG_ARM_ERRATA_742230 CONFIG_ARM_ERRATA_743622 CONFIG_ARM_ERRATA_751472 - CONFIG_ARM_ERRATA_794072 CONFIG_ARM_ERRATA_761320 + CONFIG_ARM_ERRATA_773022 + CONFIG_ARM_ERRATA_774769 + CONFIG_ARM_ERRATA_794072 If set, the workarounds for these ARM errata are applied early during U-Boot startup. Note that these options force the @@ -794,18 +796,10 @@ The following options need to be configured: - vxWorks boot parameters: bootvx constructs a valid bootline using the following - environments variables: bootfile, ipaddr, serverip, hostname. + environments variables: bootdev, bootfile, ipaddr, netmask, + serverip, gatewayip, hostname, othbootargs. It loads the vxWorks image pointed bootfile. - CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name - CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address - CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server - CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters - - CONFIG_SYS_VXWORKS_ADD_PARAMS - - Add it at the end of the bootline. E.g "u=username pw=secret" - Note: If a "bootargs" environment is defined, it will overwride the defaults discussed just above. @@ -840,18 +834,6 @@ The following options need to be configured: define this to a list of base addresses for each (supported) port. See e.g. include/configs/versatile.h - CONFIG_PL011_SERIAL_RLCR - - Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500) - have separate receive and transmit line control registers. Set - this variable to initialize the extra register. - - CONFIG_PL011_SERIAL_FLUSH_ON_INIT - - On some platforms (e.g. U8500) U-Boot is loaded by a second stage - boot loader that has already initialized the UART. Define this - variable to flush the UART at init time. - CONFIG_SERIAL_HW_FLOW_CONTROL Define this variable to enable hw flow control in serial driver. @@ -1490,16 +1472,10 @@ The following options need to be configured: CONFIG_TPM Support TPM devices. - CONFIG_TPM_TIS_I2C - Support for i2c bus TPM devices. Only one device + CONFIG_TPM_TIS_INFINEON + Support for Infineon i2c bus TPM devices. Only one device per system is supported at this time. - CONFIG_TPM_TIS_I2C_BUS_NUMBER - Define the the i2c bus number for the TPM device - - CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS - Define the TPM's address on the i2c bus - CONFIG_TPM_TIS_I2C_BURST_LIMITATION Define the burst count bytes upper limit @@ -2377,16 +2353,20 @@ CBFS (Coreboot Filesystem) support - drivers/i2c/i2c_mxc.c - activate this driver with CONFIG_SYS_I2C_MXC + - enable bus 1 with CONFIG_SYS_I2C_MXC_I2C1 + - enable bus 2 with CONFIG_SYS_I2C_MXC_I2C2 + - enable bus 3 with CONFIG_SYS_I2C_MXC_I2C3 + - enable bus 4 with CONFIG_SYS_I2C_MXC_I2C4 - define speed for bus 1 with CONFIG_SYS_MXC_I2C1_SPEED - define slave for bus 1 with CONFIG_SYS_MXC_I2C1_SLAVE - define speed for bus 2 with CONFIG_SYS_MXC_I2C2_SPEED - define slave for bus 2 with CONFIG_SYS_MXC_I2C2_SLAVE - define speed for bus 3 with CONFIG_SYS_MXC_I2C3_SPEED - define slave for bus 3 with CONFIG_SYS_MXC_I2C3_SLAVE + - define speed for bus 4 with CONFIG_SYS_MXC_I2C4_SPEED + - define slave for bus 4 with CONFIG_SYS_MXC_I2C4_SLAVE If those defines are not set, default value is 100000 for speed, and 0 for slave. - - enable bus 3 with CONFIG_SYS_I2C_MXC_I2C3 - - enable bus 4 with CONFIG_SYS_I2C_MXC_I2C4 - drivers/i2c/rcar_i2c.c: - activate this driver with CONFIG_SYS_I2C_RCAR @@ -3514,6 +3494,10 @@ FIT uImage format: without a fastmap. default: 0 + CONFIG_MTD_UBI_FM_DEBUG + Enable UBI fastmap debug + default: 0 + - UBIFS support CONFIG_CMD_UBIFS @@ -5470,10 +5454,10 @@ List of environment variables (most likely not complete): unset, then it will be made silent if the U-Boot console is silent. - tftpsrcport - If this is set, the value is used for TFTP's + tftpsrcp - If this is set, the value is used for TFTP's UDP source port. - tftpdstport - If this is set, the value is used for TFTP's UDP + tftpdstp - If this is set, the value is used for TFTP's UDP destination port instead of the Well Know Port 69. tftpblocksize - Block size to use for TFTP transfers; if not set, @@ -5487,6 +5471,14 @@ List of environment variables (most likely not complete): faster in networks with high packet loss rates or with unreliable TFTP servers. + tftptimeoutcountmax - maximum count of TFTP timeouts (no + unit, minimum value = 0). Defines how many timeouts + can happen during a single file transfer before that + transfer is aborted. The default is 10, and 0 means + 'no timeouts allowed'. Increasing this value may help + downloads succeed with high packet loss rates, or with + unreliable TFTP servers or client hardware. + vlan - When set to a value < 4095 the traffic over Ethernet is encapsulated/received over 802.1q VLAN tagged frames.