X-Git-Url: http://git.ipfire.org/?a=blobdiff_plain;f=include%2Fcommproc.h;h=9536b135dcf6620eb9624e6f12992a84f93eab18;hb=refs%2Fheads%2Fmaster;hp=9d4cb109adde161251a9ae18ac6625ae6b5f9f9d;hpb=79a34b71c943a80af5c6d9a2af736fbb37dcc14c;p=people%2Fms%2Fu-boot.git diff --git a/include/commproc.h b/include/commproc.h index 9d4cb109ad..9536b135dc 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -7,7 +7,7 @@ * * This file contains structures and information for the communication * processor channels. Some CPM control and status is available - * throught the MPC8xx internal memory map. See immap.h for details. + * through the MPC8xx internal memory map. See immap.h for details. * This file only contains what I need for the moment, not the total * CPM capabilities. I (or someone else) will add definitions as they * are needed. -- Dan @@ -60,18 +60,6 @@ #define CPM_POST_BASE 0x0980 #define CPM_WLKBD_BASE 0x0a00 -#ifndef CONFIG_SYS_CPM_POST_WORD_ADDR -#define CPM_POST_WORD_ADDR 0x07FC -#else -#define CPM_POST_WORD_ADDR CONFIG_SYS_CPM_POST_WORD_ADDR -#endif - -#ifndef CONFIG_SYS_CPM_BOOTCOUNT_ADDR -#define CPM_BOOTCOUNT_ADDR (CPM_POST_WORD_ADDR - 2*sizeof(ulong)) -#else -#define CPM_BOOTCOUNT_ADDR CONFIG_SYS_CPM_BOOTCOUNT_ADDR -#endif - #define BD_IIC_START ((uint) 0x0400) /* <- please use CPM_I2C_BASE !! */ /* Export the base address of the communication processor registers @@ -93,7 +81,7 @@ typedef struct cpm_buf_desc { #define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */ #define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */ #define BD_SC_TC ((ushort)0x0400) /* Transmit CRC */ -#define BD_SC_CM ((ushort)0x0200) /* Continous mode */ +#define BD_SC_CM ((ushort)0x0200) /* Continuous mode */ #define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */ #define BD_SC_P ((ushort)0x0100) /* xmt preamble */ #define BD_SC_BR ((ushort)0x0020) /* Break received */ @@ -405,156 +393,6 @@ typedef struct scc_enet { ushort sen_taddrl; /* temp address (LSB) */ } scc_enet_t; -/********************************************************************** - * - * Board specific configuration settings. - * - * Please note that we use the presence of a #define SCC_ENET and/or - * #define FEC_ENET to enable the SCC resp. FEC ethernet drivers. - **********************************************************************/ - -/*** BSEIP **********************************************************/ - -#ifdef CONFIG_BSEIP -/* This ENET stuff is for the MPC823 with ethernet on SCC2. - * This is unique to the BSE ip-Engine board. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) -#define PA_ENET_TXD ((ushort)0x0008) -#define PA_ENET_TCLK ((ushort)0x0100) -#define PA_ENET_RCLK ((ushort)0x0200) -#define PB_ENET_TENA ((uint)0x00002000) -#define PC_ENET_CLSN ((ushort)0x0040) -#define PC_ENET_RENA ((ushort)0x0080) - -/* BSE uses port B and C bits for PHY control also. -*/ -#define PB_BSE_POWERUP ((uint)0x00000004) -#define PB_BSE_FDXDIS ((uint)0x00008000) -#define PC_BSE_LOOPBACK ((ushort)0x0800) - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002c00) -#endif /* CONFIG_BSEIP */ - -/*** KM8XX *********************************************************/ - -/* The KM8XX Service Module uses SCC3 for Ethernet */ - -#ifdef CONFIG_KM8XX -#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */ -#define CPM_CR_ENET CPM_CR_CH_SCC3 -#define SCC_ENET 2 -#define PA_ENET_RXD ((ushort)0x0010) /* PA 11 */ -#define PA_ENET_TXD ((ushort)0x0020) /* PA 10 */ -#define PA_ENET_RCLK ((ushort)0x1000) /* PA 3 CLK 5 */ -#define PA_ENET_TCLK ((ushort)0x2000) /* PA 2 CLK 6 */ - -#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */ - -#define PC_ENET_RENA ((ushort)0x0200) /* PC 6 */ -#define PC_ENET_CLSN ((ushort)0x0100) /* PC 7 */ - -/* Control bits in the SICR to route TCLK (CLK6) and RCLK (CLK5) to - * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero. - */ -#define SICR_ENET_MASK ((uint)0x00FF0000) -#define SICR_ENET_CLKRT ((uint)0x00250000) -#endif /* CONFIG_KM8XX */ - -/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/ - -#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \ - defined(CONFIG_TQM823L) || \ - defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \ - defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D) - -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC2 use. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */ -#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ - -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ - -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ - -/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to - * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. - */ -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002600) - -# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */ -#define FEC_ENET -# endif /* CONFIG_FEC_ENET */ - -#endif /* CONFIG_MVS v1, CONFIG_TQM823L/M, CONFIG_TQM850L/M, etc. */ - -/*** TQM855L/M, TQM860L/M, TQM862L/M, TQM866L/M *********************/ - -#if defined(CONFIG_TQM855L) || defined(CONFIG_TQM855M) || \ - defined(CONFIG_TQM860L) || defined(CONFIG_TQM860M) || \ - defined(CONFIG_TQM862L) || defined(CONFIG_TQM862M) || \ - defined(CONFIG_TQM866L) || defined(CONFIG_TQM866M) - -# ifdef CONFIG_SCC1_ENET /* use SCC for 10Mbps Ethernet */ - -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC1 use. - */ -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 -#define SCC_ENET 0 -#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */ -#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */ -#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */ -#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ - -#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */ -#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */ -#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */ - -/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to - * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero. - */ -#define SICR_ENET_MASK ((uint)0x000000ff) -#define SICR_ENET_CLKRT ((uint)0x00000026) - -# endif /* CONFIG_SCC1_ENET */ - -# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */ - -#define FEC_ENET - -#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ -#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ -#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ -#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ -#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ -#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ -#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ -#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ -#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ -#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ -#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ -#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ -#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ - -#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ - -# endif /* CONFIG_FEC_ENET */ -#endif /* CONFIG_TQM855L/M, TQM860L/M, TQM862L/M */ - /*********************************************************************/ /* SCC Event register as used by Ethernet. @@ -744,8 +582,8 @@ typedef struct spi { #define SPMODE_LENMSK ((ushort)0x00f0) /* character length */ #define SPMODE_PMMSK ((ushort)0x000f) /* prescale modulus */ -#define SPMODE_LEN(x) ((((x)-1)&0xF)<<4) -#define SPMODE_PM(x) ((x) &0xF) +#define SPMODE_LEN(x) ((((x) - 1) & 0xF) << 4) +#define SPMODE_PM(x) ((x) & 0xF) /* HDLC parameter RAM. */ @@ -834,7 +672,7 @@ typedef struct hdlc_pram_s { #define CPMVEC_PIO_PC4 ((ushort)0x01 | CPMVEC_OFFSET) #define CPMVEC_ERROR ((ushort)0x00 | CPMVEC_OFFSET) -extern void irq_install_handler(int vec, void (*handler)(void *), void *dev_id); +void irq_install_handler(int vec, void (*handler)(void *), void *dev_id); /* CPM interrupt configuration vector. */ @@ -842,7 +680,7 @@ extern void irq_install_handler(int vec, void (*handler)(void *), void *dev_id); #define CICR_SCC_SCC3 ((uint)0x00200000) /* SCC3 @ SCCc */ #define CICR_SCB_SCC2 ((uint)0x00040000) /* SCC2 @ SCCb */ #define CICR_SCA_SCC1 ((uint)0x00000000) /* SCC1 @ SCCa */ -#define CICR_IRL_MASK ((uint)0x0000e000) /* Core interrrupt */ +#define CICR_IRL_MASK ((uint)0x0000e000) /* Core interrupt */ #define CICR_HP_MASK ((uint)0x00001f00) /* Hi-pri int. */ #define CICR_IEN ((uint)0x00000080) /* Int. enable */ #define CICR_SPS ((uint)0x00000001) /* SCC Spread */