X-Git-Url: http://git.ipfire.org/?a=blobdiff_plain;f=include%2Fcommproc.h;h=9582746153a78a19aeab7cd39b636452518568dd;hb=af6da69f47314e0e8efa3711ffadbfda8d2334aa;hp=ef59df9388a3340873b2d68b937c46d9e82f571d;hpb=0657e46e28a3b0cf5fe1219f50a9f99fe7f9e90a;p=people%2Fms%2Fu-boot.git diff --git a/include/commproc.h b/include/commproc.h index ef59df9388..9582746153 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -456,319 +456,6 @@ typedef struct scc_enet { #define SICR_ENET_CLKRT ((uint)0x00002c00) #endif /* CONFIG_BSEIP */ -/*** BSEIP **********************************************************/ - -#ifdef CONFIG_FLAGADM -/* Enet configuration for the FLAGADM */ -/* Enet on SCC2 */ - -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) -#define PA_ENET_TXD ((ushort)0x0008) -#define PA_ENET_TCLK ((ushort)0x0100) -#define PA_ENET_RCLK ((ushort)0x0400) -#define PB_ENET_TENA ((uint)0x00002000) -#define PC_ENET_CLSN ((ushort)0x0040) -#define PC_ENET_RENA ((ushort)0x0080) - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00003400) -#endif /* CONFIG_FLAGADM */ - -/*** ELPT860 *********************************************************/ - -#ifdef CONFIG_ELPT860 -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC1 use. - */ -# define PROFF_ENET PROFF_SCC1 -# define CPM_CR_ENET CPM_CR_CH_SCC1 -# define SCC_ENET 0 - -# define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */ -# define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */ -# define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */ -# define PA_ENET_TCLK ((ushort)0x0200) /* PA 6 */ - -# define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */ -# define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */ -# define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */ - -/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK1) to - * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero. - */ -# define SICR_ENET_MASK ((uint)0x000000FF) -# define SICR_ENET_CLKRT ((uint)0x00000025) -#endif /* CONFIG_ELPT860 */ - -/*** ESTEEM 192E **************************************************/ -#ifdef CONFIG_ESTEEM192E -/* ESTEEM192E - * This ENET stuff is for the MPC850 with ethernet on SCC2. This - * is very similar to the RPX-Lite configuration. - * Note TENA , LOOPBACK , FDPLEX_DIS on Port B. - */ - -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 - -#define PA_ENET_RXD ((ushort)0x0004) -#define PA_ENET_TXD ((ushort)0x0008) -#define PA_ENET_TCLK ((ushort)0x0200) -#define PA_ENET_RCLK ((ushort)0x0800) -#define PB_ENET_TENA ((uint)0x00002000) -#define PC_ENET_CLSN ((ushort)0x0040) -#define PC_ENET_RENA ((ushort)0x0080) - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00003d00) - -#define PB_ENET_LOOPBACK ((uint)0x00004000) -#define PB_ENET_FDPLEX_DIS ((uint)0x00008000) - -#endif - -/*** FADS860T********************************************************/ - -#if defined(CONFIG_FADS) && defined(CONFIG_MPC86x) -/* - * This ENET stuff is for the MPC86xFADS/MPC8xxADS with ethernet on SCC1. - */ -#ifdef CONFIG_SCC1_ENET - -#define SCC_ENET 0 - -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 - -#define PA_ENET_RXD ((ushort)0x0001) -#define PA_ENET_TXD ((ushort)0x0002) -#define PA_ENET_TCLK ((ushort)0x0100) -#define PA_ENET_RCLK ((ushort)0x0200) - -#define PB_ENET_TENA ((uint)0x00001000) - -#define PC_ENET_CLSN ((ushort)0x0010) -#define PC_ENET_RENA ((ushort)0x0020) - -#define SICR_ENET_MASK ((uint)0x000000ff) -#define SICR_ENET_CLKRT ((uint)0x0000002c) - -#endif /* CONFIG_SCC1_ETHERNET */ - -/* - * This ENET stuff is for the MPC860TFADS/MPC86xADS/MPC885ADS - * with ethernet on FEC. - */ - -#ifdef CONFIG_FEC_ENET -#define FEC_ENET /* Use FEC for Ethernet */ -#endif /* CONFIG_FEC_ENET */ - -#endif /* CONFIG_FADS && CONFIG_MPC86x */ - -/*** FPS850L, FPS860L ************************************************/ - -#if defined(CONFIG_FPS850L) || defined(CONFIG_FPS860L) -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC2 use. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */ -#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ - -#define PC_ENET_TENA ((ushort)0x0002) /* PC 14 */ -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ - -/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to - * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. - */ -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002600) -#endif /* CONFIG_FPS850L, CONFIG_FPS860L */ - -/*** GEN860T **********************************************************/ -#if defined(CONFIG_GEN860T) -#undef SCC_ENET -#define FEC_ENET - -#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ -#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ -#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ -#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ -#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ -#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ -#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ -#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ -#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ -#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ -#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ -#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ -#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ -#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3-15 */ -#endif /* CONFIG_GEN860T */ - -/*** HERMES-PRO ******************************************************/ - -/* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */ - -#ifdef CONFIG_HERMES - -#define FEC_ENET /* use FEC for EThernet */ -#undef SCC_ENET - - -#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ -#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ -#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ -#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ -#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ -#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ -#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ -#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ -#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ -#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ -#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ -#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ -#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ - -#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ - -#endif /* CONFIG_HERMES */ - -/*** ICU862 **********************************************************/ - -#if defined(CONFIG_ICU862) - -#ifdef CONFIG_FEC_ENET -#define FEC_ENET /* use FEC for EThernet */ -#endif /* CONFIG_FEC_ETHERNET */ - -#endif /* CONFIG_ICU862 */ - -/*** IP860 **********************************************************/ - -#if defined(CONFIG_IP860) -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC1 use. - */ -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 -#define SCC_ENET 0 -#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */ -#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */ -#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ -#define PA_ENET_TCLK ((ushort)0x0100) /* PA 7 */ - -#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */ -#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */ -#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */ - -#define PB_ENET_RESET (uint)0x00000008 /* PB 28 */ -#define PB_ENET_JABD (uint)0x00000004 /* PB 29 */ - -/* Control bits in the SICR to route TCLK (CLK1) and RCLK (CLK2) to - * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero. - */ -#define SICR_ENET_MASK ((uint)0x000000ff) -#define SICR_ENET_CLKRT ((uint)0x0000002C) -#endif /* CONFIG_IP860 */ - -/*** IVMS8 **********************************************************/ - -/* The IVMS8 uses the FEC on a MPC860T for Ethernet */ - -#if defined(CONFIG_IVMS8) || defined(CONFIG_IVML24) - -#define FEC_ENET /* use FEC for EThernet */ -#undef SCC_ENET - -#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */ - -#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */ - -#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ -#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ -#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ -#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ -#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ -#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ -#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ -#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ -#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ -#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ -#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ -#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ -#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ - -#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ - -#endif /* CONFIG_IVMS8, CONFIG_IVML24 */ - -/*** KUP4K, KUP4X ****************************************************/ -/* The KUP4 boards uses the FEC on a MPC8xx for Ethernet */ - -#if defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X) - -#define FEC_ENET /* use FEC for EThernet */ -#undef SCC_ENET - -#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */ - -#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */ - -#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ -#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ -#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ -#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ -#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ -#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ -#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ -#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ -#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ -#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ -#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ -#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ -#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ - -#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ - -#endif /* CONFIG_KUP4K */ - -/*** LWMON **********************************************************/ - -#if defined(CONFIG_LWMON) -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC2 use. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0800) /* PA 4 */ -#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ - -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ - -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ - -/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK4) to - * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. - */ -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00003E00) -#endif /* CONFIG_LWMON */ - /*** KM8XX *********************************************************/ /* The KM8XX Service Module uses SCC3 for Ethernet */ @@ -794,194 +481,19 @@ typedef struct scc_enet { #define SICR_ENET_CLKRT ((uint)0x00250000) #endif /* CONFIG_KM8XX */ - -/*** MHPC ********************************************************/ - -#if defined(CONFIG_MHPC) -/* This ENET stuff is for the MHPC with ethernet on SCC2. - * Note TENA is on Port B. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ -#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002e00) /* RCLK-CLK2, TCLK-CLK3 */ -#endif /* CONFIG_MHPC */ - -/*** NETVIA *******************************************************/ - -/* SinoVee Microsystems SC8xx series FEL8xx-AT,SC823,SC850,SC855T,SC860T */ -#if ( defined CONFIG_SVM_SC8xx ) -# ifndef CONFIG_FEC_ENET - -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 - - /* Bits in parallel I/O port registers that have to be set/cleared - * * * * to configure the pins for SCC2 use. - * * * */ -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0400) /* PA 5 */ -#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */ - -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ - -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ -/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to - * * * * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. - * * * */ -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00003700) - -# else /* Use FEC for Fast Ethernet */ - -#undef SCC_ENET -#define FEC_ENET - -#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ -#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ -#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ -#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ -#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ -#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ -#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ -#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ -#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ -#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ -#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ -#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ -#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ - -#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ - -# endif /* CONFIG_FEC_ENET */ -#endif /* CONFIG_SVM_SC8xx */ - - -#if defined(CONFIG_NETVIA) -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC2 use. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ -#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */ - -#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1 -# define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */ -#elif CONFIG_NETVIA_VERSION >= 2 -# define PC_ENET_PDN ((ushort)0x0008) /* PC 12 */ -#endif - -#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */ - -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ - -/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to - * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. - */ -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002f00) - -#endif /* CONFIG_NETVIA */ - -/*** SM850 *********************************************************/ - -/* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */ - -#ifdef CONFIG_SM850 -#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */ -#define CPM_CR_ENET CPM_CR_CH_SCC3 -#define SCC_ENET 2 -#define PB_ENET_RXD ((uint)0x00000004) /* PB 29 */ -#define PB_ENET_TXD ((uint)0x00000002) /* PB 30 */ -#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */ -#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ - -#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */ -#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */ - -#define PC_ENET_RENA ((ushort)0x0800) /* PC 4 */ -#define PC_ENET_CLSN ((ushort)0x0400) /* PC 5 */ - -/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to - * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero. - */ -#define SICR_ENET_MASK ((uint)0x00FF0000) -#define SICR_ENET_CLKRT ((uint)0x00260000) -#endif /* CONFIG_SM850 */ - -/*** SPD823TS ******************************************************/ - -#ifdef CONFIG_SPD823TS -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC2 use. - */ -#define PROFF_ENET PROFF_SCC2 /* Ethernet on SCC2 */ -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_MDC ((ushort)0x0001) /* PA 15 !!! */ -#define PA_ENET_MDIO ((ushort)0x0002) /* PA 14 !!! */ -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ -#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ - -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ - -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ -#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 !!! */ - -/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to - * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. - */ -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002E00) -#endif /* CONFIG_SPD823TS */ - -/*** SXNI855T ******************************************************/ - -#if defined(CONFIG_SXNI855T) - -#ifdef CONFIG_FEC_ENET -#define FEC_ENET /* use FEC for Ethernet */ -#endif /* CONFIG_FEC_ETHERNET */ - -#endif /* CONFIG_SXNI855T */ - /*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/ #if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \ - defined(CONFIG_R360MPI) || defined(CONFIG_RBC823) || \ - defined(CONFIG_RRVISION)|| defined(CONFIG_TQM823L) || \ + defined(CONFIG_TQM823L) || \ defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \ - defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D) || \ - defined(CONFIG_RRVISION)|| defined(CONFIG_VIRTLAB2) + defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D) /* Bits in parallel I/O port registers that have to be set/cleared * to configure the pins for SCC2 use. */ #define PROFF_ENET PROFF_SCC2 #define CPM_CR_ENET CPM_CR_CH_SCC2 -#if (!defined(CONFIG_TK885D)) /* TK885D does not use SCC Ethernet */ #define SCC_ENET 1 -#endif #define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ #define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ #define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */ @@ -991,9 +503,6 @@ typedef struct scc_enet { #define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ #define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ -#if defined(CONFIG_R360MPI) -#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */ -#endif /* CONFIG_R360MPI */ /* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. @@ -1062,29 +571,6 @@ typedef struct scc_enet { # endif /* CONFIG_FEC_ENET */ #endif /* CONFIG_TQM855L/M, TQM860L/M, TQM862L/M */ -/*** V37 **********************************************************/ - -#ifdef CONFIG_V37 -/* This ENET stuff is for the MPC823 with ethernet on SCC2. Some of - * this may be unique to the Marel V37 configuration. - * Note TENA is on Port B. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) -#define PA_ENET_TXD ((ushort)0x0008) -#define PA_ENET_TCLK ((ushort)0x0400) -#define PA_ENET_RCLK ((ushort)0x0200) -#define PB_ENET_TENA ((uint)0x00002000) -#define PC_ENET_CLSN ((ushort)0x0040) -#define PC_ENET_RENA ((ushort)0x0080) - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002e00) -#endif /* CONFIG_V37 */ - - /*********************************************************************/ /* SCC Event register as used by Ethernet.