X-Git-Url: http://git.ipfire.org/?a=blobdiff_plain;f=include%2Fps2mult.h;h=1a38733b7649af5a240e26d832dae51587cf89a2;hb=abf54bf978ed9932d69ee7f937012398d0d8d08f;hp=599cb6dc42ddbf82ac524d10d4dedaf145baf331;hpb=cb5473205206c7f14cbb1e747f28ec75b48826e2;p=people%2Fms%2Fu-boot.git

diff --git a/include/ps2mult.h b/include/ps2mult.h
index 599cb6dc42..1a38733b76 100644
--- a/include/ps2mult.h
+++ b/include/ps2mult.h
@@ -53,103 +53,4 @@ struct serial_state {
 	u8	*iomem_base;
 };
 
-#define UART_RX		0	/* In:  Receive buffer (DLAB=0) */
-#define UART_TX		0	/* Out: Transmit buffer (DLAB=0) */
-#define UART_DLL	0	/* Out: Divisor Latch Low (DLAB=1) */
-
-#define UART_DLM	1	/* Out: Divisor Latch High (DLAB=1) */
-#define UART_IER	1	/* Out: Interrupt Enable Register */
-
-#define UART_IIR	2	/* In:  Interrupt ID Register */
-#define UART_FCR	2	/* Out: FIFO Control Register */
-
-#define UART_LCR	3	/* Out: Line Control Register */
-#define UART_MCR	4	/* Out: Modem Control Register */
-#define UART_LSR	5	/* In:  Line Status Register */
-#define UART_MSR	6	/* In:  Modem Status Register */
-#define UART_SCR	7	/* I/O: Scratch Register */
-
-/*
- * These are the definitions for the FIFO Control Register
- * (16650 only)
- */
-#define UART_FCR_ENABLE_FIFO	0x01 /* Enable the FIFO */
-#define UART_FCR_CLEAR_RCVR	0x02 /* Clear the RCVR FIFO */
-#define UART_FCR_CLEAR_XMIT	0x04 /* Clear the XMIT FIFO */
-#define UART_FCR_DMA_SELECT	0x08 /* For DMA applications */
-#define UART_FCR_TRIGGER_MASK	0xC0 /* Mask for the FIFO trigger range */
-#define UART_FCR_TRIGGER_1	0x00 /* Mask for trigger set at 1 */
-#define UART_FCR_TRIGGER_4	0x40 /* Mask for trigger set at 4 */
-#define UART_FCR_TRIGGER_8	0x80 /* Mask for trigger set at 8 */
-#define UART_FCR_TRIGGER_14	0xC0 /* Mask for trigger set at 14 */
-
-/*
- * These are the definitions for the Line Control Register
- *
- * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
- * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
- */
-#define UART_LCR_DLAB	0x80	/* Divisor latch access bit */
-#define UART_LCR_SBC	0x40	/* Set break control */
-#define UART_LCR_SPAR	0x20	/* Stick parity (?) */
-#define UART_LCR_EPAR	0x10	/* Even parity select */
-#define UART_LCR_PARITY	0x08	/* Parity Enable */
-#define UART_LCR_STOP	0x04	/* Stop bits: 0=1 stop bit, 1= 2 stop bits */
-#define UART_LCR_WLEN5  0x00	/* Wordlength: 5 bits */
-#define UART_LCR_WLEN6  0x01	/* Wordlength: 6 bits */
-#define UART_LCR_WLEN7  0x02	/* Wordlength: 7 bits */
-#define UART_LCR_WLEN8  0x03	/* Wordlength: 8 bits */
-
-/*
- * These are the definitions for the Line Status Register
- */
-#define UART_LSR_TEMT	0x40	/* Transmitter empty */
-#define UART_LSR_THRE	0x20	/* Transmit-hold-register empty */
-#define UART_LSR_BI	0x10	/* Break interrupt indicator */
-#define UART_LSR_FE	0x08	/* Frame error indicator */
-#define UART_LSR_PE	0x04	/* Parity error indicator */
-#define UART_LSR_OE	0x02	/* Overrun error indicator */
-#define UART_LSR_DR	0x01	/* Receiver data ready */
-
-/*
- * These are the definitions for the Interrupt Identification Register
- */
-#define UART_IIR_NO_INT	0x01	/* No interrupts pending */
-#define UART_IIR_ID	0x06	/* Mask for the interrupt ID */
-
-#define UART_IIR_MSI	0x00	/* Modem status interrupt */
-#define UART_IIR_THRI	0x02	/* Transmitter holding register empty */
-#define UART_IIR_RDI	0x04	/* Receiver data interrupt */
-#define UART_IIR_RLSI	0x06	/* Receiver line status interrupt */
-
-/*
- * These are the definitions for the Interrupt Enable Register
- */
-#define UART_IER_MSI	0x08	/* Enable Modem status interrupt */
-#define UART_IER_RLSI	0x04	/* Enable receiver line status interrupt */
-#define UART_IER_THRI	0x02	/* Enable Transmitter holding register int. */
-#define UART_IER_RDI	0x01	/* Enable receiver data interrupt */
-
-/*
- * These are the definitions for the Modem Control Register
- */
-#define UART_MCR_LOOP	0x10	/* Enable loopback test mode */
-#define UART_MCR_OUT2	0x08	/* Out2 complement */
-#define UART_MCR_OUT1	0x04	/* Out1 complement */
-#define UART_MCR_RTS	0x02	/* RTS complement */
-#define UART_MCR_DTR	0x01	/* DTR complement */
-
-/*
- * These are the definitions for the Modem Status Register
- */
-#define UART_MSR_DCD	0x80	/* Data Carrier Detect */
-#define UART_MSR_RI	0x40	/* Ring Indicator */
-#define UART_MSR_DSR	0x20	/* Data Set Ready */
-#define UART_MSR_CTS	0x10	/* Clear to Send */
-#define UART_MSR_DDCD	0x08	/* Delta DCD */
-#define UART_MSR_TERI	0x04	/* Trailing edge ring indicator */
-#define UART_MSR_DDSR	0x02	/* Delta DSR */
-#define UART_MSR_DCTS	0x01	/* Delta CTS */
-#define UART_MSR_ANY_DELTA 0x0F	/* Any of the delta bits! */
-
 #endif /* __LINUX_PS2MULT_H */