static void ath_ant_set_alt_ratio(struct ath_ant_comb *antcomb,
struct ath_hw_antcomb_conf *conf)
{
- /* set alt to the conf with maximun ratio */
+ /* set alt to the conf with maximum ratio */
if (antcomb->first_ratio && antcomb->second_ratio) {
if (antcomb->rssi_second > antcomb->rssi_third) {
/* first alt*/
ah->config.hw_hang_checks |= HW_MAC_HANG;
}
-/* Sets up the AR5008/AR9001/AR9002 hardware familiy callbacks */
+/* Sets up the AR5008/AR9001/AR9002 hardware family callbacks */
int ar9002_hw_attach_ops(struct ath_hw *ah)
{
struct ath_hw_private_ops *priv_ops = ath9k_hw_private_ops(ah);
return false;
}
-/* Sets up the AR9003 hardware familiy callbacks */
+/* Sets up the AR9003 hardware family callbacks */
void ar9003_hw_attach_ops(struct ath_hw *ah)
{
struct ath_hw_private_ops *priv_ops = ath9k_hw_private_ops(ah);
* same time. Since BT's calibration doesn't happen
* that often, we'll let BT completes calibration then
* we continue to wait for cal_grant from BT.
- * Orginal: Wait BT_CAL_GRANT.
+ * Original: Wait BT_CAL_GRANT.
* New: Receive BT_CAL_REQ -> send WLAN_CAL_GRANT->wait
* BT_CAL_DONE -> Wait BT_CAL_GRANT.
*/
* BT is sleeping. Check if BT wakes up during
* WLAN calibration. If BT wakes up during
* WLAN calibration, need to go through all
- * message exchanges again and recal.
+ * message exchanges again and recalibrate.
*/
REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
(AR_MCI_INTERRUPT_RX_MSG_REMOTE_RESET |
/*
- * MRC Feild Definitions
+ * MRC Field Definitions
*/
#define AR_PHY_SGI_DSC_MAN 0x0007FFF0
#define AR_PHY_SGI_DSC_MAN_S 4
#include "ath9k.h"
/* Set/change channels. If the channel is really being changed, it's done
- * by reseting the chip. To accomplish this we must first cleanup any pending
+ * by resetting the chip. To accomplish this we must first cleanup any pending
* DMA, then restart stuff.
*/
static int ath_set_channel(struct ath_softc *sc)
ATH9K_RX_FILTER_PHYRADAR |
ATH9K_RX_FILTER_PHYERR);
- /* TODO: usually this should not be neccesary, but for some reason
+ /* TODO: usually this should not be necessary, but for some reason
* (or in some mode?) the trigger must be called after the
* configuration, otherwise the register will have its values reset
* (on my ar9220 to value 0x01002310)
const int DFS_UPPER_BIN_OFFSET = 64;
/* if detected radar on both channels, select the significant one */
if (is_ctl && is_ext) {
- /* first check wether channels have 'strong' bins */
+ /* first check whether channels have 'strong' bins */
is_ctl = fft_bitmap_weight(fft->lower_bins) != 0;
is_ext = fft_bitmap_weight(fft->upper_bins) != 0;
filename = FIRMWARE_AR9271;
/* expected fw locations:
- * - htc_9271.fw (stable version 1.3, depricated)
+ * - htc_9271.fw (stable version 1.3, deprecated)
*/
snprintf(hif_dev->fw_name, sizeof(hif_dev->fw_name),
"%s", filename);
/* When chip goes into network sleep, it could be waken
* up by MCI_INT interrupt caused by BT's HW messages
- * (LNA_xxx, CONT_xxx) which chould be in a very fast
+ * (LNA_xxx, CONT_xxx) which could be in a very fast
* rate (~100us). This will cause chip to leave and
* re-enter network sleep mode frequently, which in
* consequence will have WLAN MCI HW to generate lots of
pCap->tx_chainmask = ah->eep_ops->get_eeprom(ah, EEP_TX_MASK);
/*
- * For AR9271 we will temporarilly uses the rx chainmax as read from
+ * For AR9271 we will temporarily use the rx chainmax as read from
* the EEPROM.
*/
if ((ah->hw_version.devid == AR5416_DEVID_PCI) &&
* an exact user defined pattern or de-authentication/disassoc pattern.
* @ATH9K_HW_WOW_PATTERN_MATCH_DWORD: device requires the first four
* bytes of the pattern for user defined pattern, de-authentication and
- * disassociation patterns for all types of possible frames recieved
+ * disassociation patterns for all types of possible frames received
* of those types.
*/
* when the descriptor is specifically marked to generate
* an interrupt with this flag. Descriptors should be
* marked periodically to insure timely replenishing of the
- * supply needed for sending frames. Defering interrupts
+ * supply needed for sending frames. Deferring interrupts
* reduces system load and potentially allows more concurrent
* work to be done but if done to aggressively can cause
* senders to backup. When the hardware queue is left too
static void ath9k_vif_iter_set_beacon(struct ath9k_vif_iter_data *iter_data,
struct ieee80211_vif *vif)
{
- /* Use the first (configured) interface, but prefering AP interfaces. */
+ /* Use the first (configured) interface, but preferring AP interfaces. */
if (!iter_data->primary_beacon_vif) {
iter_data->primary_beacon_vif = vif;
} else {
memset(dis_deauth_mask, 0, MAX_PATTERN_SIZE);
/*
- * Create Dissassociate / Deauthenticate packet filter
+ * Create Disassociate / Deauthenticate packet filter
*
* 2 bytes 2 byte 6 bytes 6 bytes 6 bytes
* +--------------+----------+---------+--------+--------+----
* The above is the management frame format for disassociate/
* deauthenticate pattern, from this we need to match the first byte
* of 'Frame Control' and DA, SA, and BSSID fields
- * (skipping 2nd byte of FC and Duration feild.
+ * (skipping 2nd byte of FC and Duration field.
*
* Disassociate pattern
* --------------------
ath9k_stop_btcoex(sc);
/*
- * Enable wake up on recieving disassoc/deauth
+ * Enable wake up on receiving disassoc/deauth
* frame by default.
*/
ret = ath9k_wow_add_disassoc_deauth_pattern(sc);
/*
* AR5416 can become deaf/mute when BA
* issue happens. Chip needs to be reset.
- * But AP code may have sychronization issues
+ * But AP code may have synchronization issues
* when perform internal reset in this routine.
* Only enable reset in STA mode for now.
*/
projects / thirdparty / kernel / linux.git / commitdiff
