Add extra parameters to vendor command GPIO attribute

Add extra parameters mux_config, drive, and init_enable
to the GPIO config command.

Signed-off-by: Nandha Kishore Easwaran <nandhaki@codeaurora.org>

diff --git a/src/common/qca-vendor.h b/src/common/qca-vendor.h
index ca9c2d1778f732a879f101f028f3881e3e190d26..d7e4dda4b2a1727a17b11e325b5866d9ff17f113 100644 (file)
--- a/src/common/qca-vendor.h
+++ b/src/common/qca-vendor.h
@@ -2438,23 +2438,50 @@ enum qca_wlan_vendor_attr_sap_conditional_chan_switch {
  * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is
  * %QCA_WLAN_VENDOR_GPIO_OUTPUT.
  *
- * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE: Required (u32)
+ * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE: Optional (u32)
  * value to specify the GPIO pull type. Please refer to enum qca_gpio_pull_type
  * for the available values.
  * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is
- * %QCA_WLAN_VENDOR_GPIO_CONFIG.
+ * %QCA_WLAN_VENDOR_GPIO_CONFIG and
+ * %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG attribute is not present.
+ * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG
+ * attribute is present.
  *
- * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE: Required (u32)
+ * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE: Optional (u32)
  * value to specify the GPIO interrupt mode. Please refer to enum
  * qca_gpio_interrupt_mode for the available values.
  * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is
- * %QCA_WLAN_VENDOR_GPIO_CONFIG.
+ * %QCA_WLAN_VENDOR_GPIO_CONFIG and
+ * %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG attribute is not present.
+ * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG
+ * attribute is present.
  *
- * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DIR: Required (u32)
+ * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DIR: Optional (u32)
  * value to specify the GPIO direction. Please refer to enum qca_gpio_direction
  * for the available values.
  * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is
- * %QCA_WLAN_VENDOR_GPIO_CONFIG.
+ * %QCA_WLAN_VENDOR_GPIO_CONFIG and
+ * %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG attribute is not present.
+ * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG
+ * attribute is present.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MUX_CONFIG: Optional (u32)
+ * Value to specify the mux config. Meaning of a given value is dependent
+ * on the target chipset and GPIO pin. Must be of the range 0-15.
+ * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is
+ * %QCA_WLAN_VENDOR_GPIO_CONFIG. Defaults to 0.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DRIVE: Optional (u32)
+ * Value to specify the drive, refer to enum qca_gpio_drive.
+ * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is
+ * %QCA_WLAN_VENDOR_GPIO_CONFIG. Defaults to QCA_WLAN_GPIO_DRIVE_2MA(0).
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG: Optional (flag)
+ * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is
+ * %QCA_WLAN_VENDOR_GPIO_CONFIG. When present this attribute signals that all
+ * other parameters for the given GPIO will be obtained from internal
+ * configuration. Only %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM must be
+ * specified to indicate the GPIO pin being configured.
  */
 enum qca_wlan_gpio_attr {
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0,
@@ -2470,6 +2497,12 @@ enum qca_wlan_gpio_attr {
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE = 5,
        /* Unsigned 32-bit attribute for GPIO direction to configure */
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DIR = 6,
+       /* Unsigned 32-bit attribute for GPIO mux config */
+       QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MUX_CONFIG = 7,
+       /* Unsigned 32-bit attribute for GPIO drive */
+       QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DRIVE = 8,
+       /* Flag attribute for using internal GPIO configuration */
+       QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG = 9,
 
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST,
@@ -2544,6 +2577,30 @@ enum qca_gpio_interrupt_mode {
        QCA_WLAN_GPIO_INTMODE_MAX,
 };
 
+/**
+ * enum qca_gpio_drive - GPIO drive
+ * @QCA_WLAN_GPIO_DRIVE_2MA: drive 2MA
+ * @QCA_WLAN_GPIO_DRIVE_4MA: drive 4MA
+ * @QCA_WLAN_GPIO_DRIVE_6MA: drive 6MA
+ * @QCA_WLAN_GPIO_DRIVE_8MA: drive 8MA
+ * @QCA_WLAN_GPIO_DRIVE_10MA: drive 10MA
+ * @QCA_WLAN_GPIO_DRIVE_12MA: drive 12MA
+ * @QCA_WLAN_GPIO_DRIVE_14MA: drive 14MA
+ * @QCA_WLAN_GPIO_DRIVE_16MA: drive 16MA
+ * @QCA_WLAN_GPIO_DRIVE_MAX: invalid GPIO drive
+ */
+enum qca_gpio_drive {
+       QCA_WLAN_GPIO_DRIVE_2MA = 0,
+       QCA_WLAN_GPIO_DRIVE_4MA = 1,
+       QCA_WLAN_GPIO_DRIVE_6MA = 2,
+       QCA_WLAN_GPIO_DRIVE_8MA = 3,
+       QCA_WLAN_GPIO_DRIVE_10MA = 4,
+       QCA_WLAN_GPIO_DRIVE_12MA = 5,
+       QCA_WLAN_GPIO_DRIVE_14MA = 6,
+       QCA_WLAN_GPIO_DRIVE_16MA = 7,
+       QCA_WLAN_GPIO_DRIVE_MAX,
+};
+
 /**
  * qca_wlan_set_qdepth_thresh_attr - Parameters for setting
  * MSDUQ depth threshold per peer per tid in the target