media: doc/dt-bindings: remove support of stih407-c8sectpfe

Remove files documentation from stih407-c8sectpfe driver.

Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
[hverkuil: slight change of the Subject, mention doc changes as well]

diff --git a/Documentation/admin-guide/media/platform-cardlist.rst b/Documentation/admin-guide/media/platform-cardlist.rst
index 1230ae4037ad551087d4cddc8a02eab5eac2be71..63f4b19c3628f3488fd2ccd1a6dab385d46b2503 100644 (file)
--- a/Documentation/admin-guide/media/platform-cardlist.rst
+++ b/Documentation/admin-guide/media/platform-cardlist.rst
@@ -18,8 +18,6 @@ am437x-vpfe        TI AM437x VPFE
 aspeed-video       Aspeed AST2400 and AST2500
 atmel-isc          ATMEL Image Sensor Controller (ISC)
 atmel-isi          ATMEL Image Sensor Interface (ISI)
-c8sectpfe          SDR platform devices
-c8sectpfe          SDR platform devices
 cafe_ccic          Marvell 88ALP01 (Cafe) CMOS Camera Controller
 cdns-csi2rx        Cadence MIPI-CSI2 RX Controller
 cdns-csi2tx        Cadence MIPI-CSI2 TX Controller

diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
deleted file mode 100644 (file)
index 880d4d7..0000000
--- a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
+++ /dev/null
@@ -1,88 +0,0 @@
-STMicroelectronics STi c8sectpfe binding
-============================================
-
-This document describes the c8sectpfe device bindings that is used to get transport
-stream data into the SoC on the TS pins, and into DDR for further processing.
-
-It is typically used in conjunction with one or more demodulator and tuner devices
-which converts from the RF to digital domain. Demodulators and tuners are usually
-located on an external DVB frontend card connected to SoC TS input pins.
-
-Currently 7 TS input (tsin) channels are supported on the stih407 family SoC.
-
-Required properties (controller (parent) node):
-- compatible   : Should be "stih407-c8sectpfe"
-
-- reg          : Address and length of register sets for each device in
-                 "reg-names"
-
-- reg-names    : The names of the register addresses corresponding to the
-                 registers filled in "reg":
-                       - c8sectpfe: c8sectpfe registers
-                       - c8sectpfe-ram: c8sectpfe internal sram
-
-- clocks       : phandle list of c8sectpfe clocks
-- clock-names  : should be "c8sectpfe"
-See: Documentation/devicetree/bindings/clock/clock-bindings.txt
-
-- pinctrl-names        : a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num)
-                  must be defined for each tsin child node.
-- pinctrl-0    : phandle referencing pin configuration for this tsin configuration
-See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
-
-
-Required properties (tsin (child) node):
-
-- tsin-num     : tsin id of the InputBlock (must be between 0 to 6)
-- i2c-bus      : phandle to the I2C bus DT node which the demodulators & tuners on this tsin channel are connected.
-- reset-gpios  : reset gpio for this tsin channel.
-
-Optional properties (tsin (child) node):
-
-- invert-ts-clk                : Bool property to control sense of ts input clock (data stored on falling edge of clk).
-- serial-not-parallel  : Bool property to configure input bus width (serial on ts_data<7>).
-- async-not-sync       : Bool property to control if data is received in asynchronous mode
-                          (all bits/bytes with ts_valid or ts_packet asserted are valid).
-
-- dvb-card             : Describes the NIM card connected to this tsin channel.
-
-Example:
-
-/* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */
-
-       c8sectpfe@8a20000 {
-               compatible = "st,stih407-c8sectpfe";
-               reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
-               reg-names = "stfe", "stfe-ram";
-               interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>;
-               interrupt-names = "stfe-error-irq", "stfe-idle-irq";
-               pinctrl-0       = <&pinctrl_tsin0_serial>;
-               pinctrl-1       = <&pinctrl_tsin0_parallel>;
-               pinctrl-2       = <&pinctrl_tsin3_serial>;
-               pinctrl-3       = <&pinctrl_tsin4_serial_alt3>;
-               pinctrl-4       = <&pinctrl_tsin5_serial_alt1>;
-               pinctrl-names   = "tsin0-serial",
-                                 "tsin0-parallel",
-                                 "tsin3-serial",
-                                 "tsin4-serial",
-                                 "tsin5-serial";
-               clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
-               clock-names = "c8sectpfe";
-
-               /* tsin0 is TSA on NIMA */
-               tsin0: port@0 {
-                       tsin-num                = <0>;
-                       serial-not-parallel;
-                       i2c-bus                 = <&ssc2>;
-                       reset-gpios             = <&pio15 4 GPIO_ACTIVE_HIGH>;
-                       dvb-card                = <STV0367_TDA18212_NIMA_1>;
-               };
-
-               tsin3: port@3 {
-                       tsin-num                = <3>;
-                       serial-not-parallel;
-                       i2c-bus                 = <&ssc3>;
-                       reset-gpios             = <&pio15 7 GPIO_ACTIVE_HIGH>;
-                       dvb-card                = <STV0367_TDA18212_NIMB_1>;
-               };
-       };