* Portions Copyright (C) Sun Microsystems 2008
*/
-#ifndef _LINUX_ETHTOOL_H
-#define _LINUX_ETHTOOL_H
+#ifndef _UAPI_LINUX_ETHTOOL_H
+#define _UAPI_LINUX_ETHTOOL_H
#include <linux/types.h>
#include <linux/if_ether.h>
-/* This should work for both 32 and 64 bit userland. */
+#ifndef __KERNEL__
+#include <limits.h> /* for INT_MAX */
+#endif
+
+/* All structures exposed to userland should be defined such that they
+ * have the same layout for 32-bit and 64-bit userland.
+ */
+
+/**
+ * struct ethtool_cmd - DEPRECATED, link control and status
+ * This structure is DEPRECATED, please use struct ethtool_link_settings.
+ * @cmd: Command number = %ETHTOOL_GSET or %ETHTOOL_SSET
+ * @supported: Bitmask of %SUPPORTED_* flags for the link modes,
+ * physical connectors and other link features for which the
+ * interface supports autonegotiation or auto-detection.
+ * Read-only.
+ * @advertising: Bitmask of %ADVERTISED_* flags for the link modes,
+ * physical connectors and other link features that are
+ * advertised through autonegotiation or enabled for
+ * auto-detection.
+ * @speed: Low bits of the speed, 1Mb units, 0 to INT_MAX or SPEED_UNKNOWN
+ * @duplex: Duplex mode; one of %DUPLEX_*
+ * @port: Physical connector type; one of %PORT_*
+ * @phy_address: MDIO address of PHY (transceiver); 0 or 255 if not
+ * applicable. For clause 45 PHYs this is the PRTAD.
+ * @transceiver: Historically used to distinguish different possible
+ * PHY types, but not in a consistent way. Deprecated.
+ * @autoneg: Enable/disable autonegotiation and auto-detection;
+ * either %AUTONEG_DISABLE or %AUTONEG_ENABLE
+ * @mdio_support: Bitmask of %ETH_MDIO_SUPPORTS_* flags for the MDIO
+ * protocols supported by the interface; 0 if unknown.
+ * Read-only.
+ * @maxtxpkt: Historically used to report TX IRQ coalescing; now
+ * obsoleted by &struct ethtool_coalesce. Read-only; deprecated.
+ * @maxrxpkt: Historically used to report RX IRQ coalescing; now
+ * obsoleted by &struct ethtool_coalesce. Read-only; deprecated.
+ * @speed_hi: High bits of the speed, 1Mb units, 0 to INT_MAX or SPEED_UNKNOWN
+ * @eth_tp_mdix: Ethernet twisted-pair MDI(-X) status; one of
+ * %ETH_TP_MDI_*. If the status is unknown or not applicable, the
+ * value will be %ETH_TP_MDI_INVALID. Read-only.
+ * @eth_tp_mdix_ctrl: Ethernet twisted pair MDI(-X) control; one of
+ * %ETH_TP_MDI_*. If MDI(-X) control is not implemented, reads
+ * yield %ETH_TP_MDI_INVALID and writes may be ignored or rejected.
+ * When written successfully, the link should be renegotiated if
+ * necessary.
+ * @lp_advertising: Bitmask of %ADVERTISED_* flags for the link modes
+ * and other link features that the link partner advertised
+ * through autonegotiation; 0 if unknown or not applicable.
+ * Read-only.
+ *
+ * The link speed in Mbps is split between @speed and @speed_hi. Use
+ * the ethtool_cmd_speed() and ethtool_cmd_speed_set() functions to
+ * access it.
+ *
+ * If autonegotiation is disabled, the speed and @duplex represent the
+ * fixed link mode and are writable if the driver supports multiple
+ * link modes. If it is enabled then they are read-only; if the link
+ * is up they represent the negotiated link mode; if the link is down,
+ * the speed is 0, %SPEED_UNKNOWN or the highest enabled speed and
+ * @duplex is %DUPLEX_UNKNOWN or the best enabled duplex mode.
+ *
+ * Some hardware interfaces may have multiple PHYs and/or physical
+ * connectors fitted or do not allow the driver to detect which are
+ * fitted. For these interfaces @port and/or @phy_address may be
+ * writable, possibly dependent on @autoneg being %AUTONEG_DISABLE.
+ * Otherwise, attempts to write different values may be ignored or
+ * rejected.
+ *
+ * Users should assume that all fields not marked read-only are
+ * writable and subject to validation by the driver. They should use
+ * %ETHTOOL_GSET to get the current values before making specific
+ * changes and then applying them with %ETHTOOL_SSET.
+ *
+ * Drivers that implement set_settings() should validate all fields
+ * other than @cmd that are not described as read-only or deprecated,
+ * and must ignore all fields described as read-only.
+ *
+ * Deprecated fields should be ignored by both users and drivers.
+ */
struct ethtool_cmd {
__u32 cmd;
- __u32 supported; /* Features this interface supports */
- __u32 advertising; /* Features this interface advertises */
- __u16 speed; /* The forced speed (lower bits) in
- * Mbps. Please use
- * ethtool_cmd_speed()/_set() to
- * access it */
- __u8 duplex; /* Duplex, half or full */
- __u8 port; /* Which connector port */
- __u8 phy_address; /* MDIO PHY address (PRTAD for clause 45).
- * May be read-only or read-write
- * depending on the driver.
- */
- __u8 transceiver; /* Which transceiver to use */
- __u8 autoneg; /* Enable or disable autonegotiation */
- __u8 mdio_support; /* MDIO protocols supported. Read-only.
- * Not set by all drivers.
- */
- __u32 maxtxpkt; /* Tx pkts before generating tx int */
- __u32 maxrxpkt; /* Rx pkts before generating rx int */
- __u16 speed_hi; /* The forced speed (upper
- * bits) in Mbps. Please use
- * ethtool_cmd_speed()/_set() to
- * access it */
+ __u32 supported;
+ __u32 advertising;
+ __u16 speed;
+ __u8 duplex;
+ __u8 port;
+ __u8 phy_address;
+ __u8 transceiver;
+ __u8 autoneg;
+ __u8 mdio_support;
+ __u32 maxtxpkt;
+ __u32 maxrxpkt;
+ __u16 speed_hi;
__u8 eth_tp_mdix;
- __u8 reserved2;
- __u32 lp_advertising; /* Features the link partner advertises */
+ __u8 eth_tp_mdix_ctrl;
+ __u32 lp_advertising;
__u32 reserved[2];
};
-static __inline__ void ethtool_cmd_speed_set(struct ethtool_cmd *ep,
+static inline void ethtool_cmd_speed_set(struct ethtool_cmd *ep,
__u32 speed)
{
ep->speed_hi = (__u16)(speed >> 16);
}
-static __inline__ __u32 ethtool_cmd_speed(const struct ethtool_cmd *ep)
+static inline __u32 ethtool_cmd_speed(const struct ethtool_cmd *ep)
{
return (ep->speed_hi << 16) | ep->speed;
}
#define ETHTOOL_FWVERS_LEN 32
#define ETHTOOL_BUSINFO_LEN 32
-/* these strings are set to whatever the driver author decides... */
+#define ETHTOOL_EROMVERS_LEN 32
+
+/**
+ * struct ethtool_drvinfo - general driver and device information
+ * @cmd: Command number = %ETHTOOL_GDRVINFO
+ * @driver: Driver short name. This should normally match the name
+ * in its bus driver structure (e.g. pci_driver::name). Must
+ * not be an empty string.
+ * @version: Driver version string; may be an empty string
+ * @fw_version: Firmware version string; may be an empty string
+ * @erom_version: Expansion ROM version string; may be an empty string
+ * @bus_info: Device bus address. This should match the dev_name()
+ * string for the underlying bus device, if there is one. May be
+ * an empty string.
+ * @n_priv_flags: Number of flags valid for %ETHTOOL_GPFLAGS and
+ * %ETHTOOL_SPFLAGS commands; also the number of strings in the
+ * %ETH_SS_PRIV_FLAGS set
+ * @n_stats: Number of u64 statistics returned by the %ETHTOOL_GSTATS
+ * command; also the number of strings in the %ETH_SS_STATS set
+ * @testinfo_len: Number of results returned by the %ETHTOOL_TEST
+ * command; also the number of strings in the %ETH_SS_TEST set
+ * @eedump_len: Size of EEPROM accessible through the %ETHTOOL_GEEPROM
+ * and %ETHTOOL_SEEPROM commands, in bytes
+ * @regdump_len: Size of register dump returned by the %ETHTOOL_GREGS
+ * command, in bytes
+ *
+ * Users can use the %ETHTOOL_GSSET_INFO command to get the number of
+ * strings in any string set (from Linux 2.6.34).
+ *
+ * Drivers should set at most @driver, @version, @fw_version and
+ * @bus_info in their get_drvinfo() implementation. The ethtool
+ * core fills in the other fields using other driver operations.
+ */
struct ethtool_drvinfo {
__u32 cmd;
- char driver[32]; /* driver short name, "tulip", "eepro100" */
- char version[32]; /* driver version string */
- char fw_version[ETHTOOL_FWVERS_LEN]; /* firmware version string */
- char bus_info[ETHTOOL_BUSINFO_LEN]; /* Bus info for this IF. */
- /* For PCI devices, use pci_name(pci_dev). */
- char reserved1[32];
+ char driver[32];
+ char version[32];
+ char fw_version[ETHTOOL_FWVERS_LEN];
+ char bus_info[ETHTOOL_BUSINFO_LEN];
+ char erom_version[ETHTOOL_EROMVERS_LEN];
char reserved2[12];
- /*
- * Some struct members below are filled in
- * using ops->get_sset_count(). Obtaining
- * this info from ethtool_drvinfo is now
- * deprecated; Use ETHTOOL_GSSET_INFO
- * instead.
- */
- __u32 n_priv_flags; /* number of flags valid in ETHTOOL_GPFLAGS */
- __u32 n_stats; /* number of u64's from ETHTOOL_GSTATS */
+ __u32 n_priv_flags;
+ __u32 n_stats;
__u32 testinfo_len;
- __u32 eedump_len; /* Size of data from ETHTOOL_GEEPROM (bytes) */
- __u32 regdump_len; /* Size of data from ETHTOOL_GREGS (bytes) */
+ __u32 eedump_len;
+ __u32 regdump_len;
};
#define SOPASS_MAX 6
-/* wake-on-lan settings */
+
+/**
+ * struct ethtool_wolinfo - Wake-On-Lan configuration
+ * @cmd: Command number = %ETHTOOL_GWOL or %ETHTOOL_SWOL
+ * @supported: Bitmask of %WAKE_* flags for supported Wake-On-Lan modes.
+ * Read-only.
+ * @wolopts: Bitmask of %WAKE_* flags for enabled Wake-On-Lan modes.
+ * @sopass: SecureOn(tm) password; meaningful only if %WAKE_MAGICSECURE
+ * is set in @wolopts.
+ */
struct ethtool_wolinfo {
__u32 cmd;
__u32 supported;
__u32 wolopts;
- __u8 sopass[SOPASS_MAX]; /* SecureOn(tm) password */
+ __u8 sopass[SOPASS_MAX];
};
/* for passing single values */
__u32 data;
};
-/* for passing big chunks of data */
+enum tunable_id {
+ ETHTOOL_ID_UNSPEC,
+ ETHTOOL_RX_COPYBREAK,
+ ETHTOOL_TX_COPYBREAK,
+ /*
+ * Add your fresh new tubale attribute above and remember to update
+ * tunable_strings[] in net/core/ethtool.c
+ */
+ __ETHTOOL_TUNABLE_COUNT,
+};
+
+enum tunable_type_id {
+ ETHTOOL_TUNABLE_UNSPEC,
+ ETHTOOL_TUNABLE_U8,
+ ETHTOOL_TUNABLE_U16,
+ ETHTOOL_TUNABLE_U32,
+ ETHTOOL_TUNABLE_U64,
+ ETHTOOL_TUNABLE_STRING,
+ ETHTOOL_TUNABLE_S8,
+ ETHTOOL_TUNABLE_S16,
+ ETHTOOL_TUNABLE_S32,
+ ETHTOOL_TUNABLE_S64,
+};
+
+struct ethtool_tunable {
+ __u32 cmd;
+ __u32 id;
+ __u32 type_id;
+ __u32 len;
+ void *data[0];
+};
+
+/**
+ * struct ethtool_regs - hardware register dump
+ * @cmd: Command number = %ETHTOOL_GREGS
+ * @version: Dump format version. This is driver-specific and may
+ * distinguish different chips/revisions. Drivers must use new
+ * version numbers whenever the dump format changes in an
+ * incompatible way.
+ * @len: On entry, the real length of @data. On return, the number of
+ * bytes used.
+ * @data: Buffer for the register dump
+ *
+ * Users should use %ETHTOOL_GDRVINFO to find the maximum length of
+ * a register dump for the interface. They must allocate the buffer
+ * immediately following this structure.
+ */
struct ethtool_regs {
__u32 cmd;
- __u32 version; /* driver-specific, indicates different chips/revs */
- __u32 len; /* bytes */
+ __u32 version;
+ __u32 len;
__u8 data[0];
};
-/* for passing EEPROM chunks */
+/**
+ * struct ethtool_eeprom - EEPROM dump
+ * @cmd: Command number = %ETHTOOL_GEEPROM, %ETHTOOL_GMODULEEEPROM or
+ * %ETHTOOL_SEEPROM
+ * @magic: A 'magic cookie' value to guard against accidental changes.
+ * The value passed in to %ETHTOOL_SEEPROM must match the value
+ * returned by %ETHTOOL_GEEPROM for the same device. This is
+ * unused when @cmd is %ETHTOOL_GMODULEEEPROM.
+ * @offset: Offset within the EEPROM to begin reading/writing, in bytes
+ * @len: On entry, number of bytes to read/write. On successful
+ * return, number of bytes actually read/written. In case of
+ * error, this may indicate at what point the error occurred.
+ * @data: Buffer to read/write from
+ *
+ * Users may use %ETHTOOL_GDRVINFO or %ETHTOOL_GMODULEINFO to find
+ * the length of an on-board or module EEPROM, respectively. They
+ * must allocate the buffer immediately following this structure.
+ */
struct ethtool_eeprom {
__u32 cmd;
__u32 magic;
- __u32 offset; /* in bytes */
- __u32 len; /* in bytes */
+ __u32 offset;
+ __u32 len;
__u8 data[0];
};
* @rate_sample_interval: How often to do adaptive coalescing packet rate
* sampling, measured in seconds. Must not be zero.
*
- * Each pair of (usecs, max_frames) fields specifies this exit
- * condition for interrupt coalescing:
+ * Each pair of (usecs, max_frames) fields specifies that interrupts
+ * should be coalesced until
* (usecs > 0 && time_since_first_completion >= usecs) ||
* (max_frames > 0 && completed_frames >= max_frames)
+ *
* It is illegal to set both usecs and max_frames to zero as this
* would cause interrupts to never be generated. To disable
* coalescing, set usecs = 0 and max_frames = 1.
*
* Some implementations ignore the value of max_frames and use the
- * condition:
- * time_since_first_completion >= usecs
+ * condition time_since_first_completion >= usecs
+ *
* This is deprecated. Drivers for hardware that does not support
* counting completions should validate that max_frames == !rx_usecs.
*
__u32 rate_sample_interval;
};
-/* for configuring RX/TX ring parameters */
+/**
+ * struct ethtool_ringparam - RX/TX ring parameters
+ * @cmd: Command number = %ETHTOOL_GRINGPARAM or %ETHTOOL_SRINGPARAM
+ * @rx_max_pending: Maximum supported number of pending entries per
+ * RX ring. Read-only.
+ * @rx_mini_max_pending: Maximum supported number of pending entries
+ * per RX mini ring. Read-only.
+ * @rx_jumbo_max_pending: Maximum supported number of pending entries
+ * per RX jumbo ring. Read-only.
+ * @tx_max_pending: Maximum supported number of pending entries per
+ * TX ring. Read-only.
+ * @rx_pending: Current maximum number of pending entries per RX ring
+ * @rx_mini_pending: Current maximum number of pending entries per RX
+ * mini ring
+ * @rx_jumbo_pending: Current maximum number of pending entries per RX
+ * jumbo ring
+ * @tx_pending: Current maximum supported number of pending entries
+ * per TX ring
+ *
+ * If the interface does not have separate RX mini and/or jumbo rings,
+ * @rx_mini_max_pending and/or @rx_jumbo_max_pending will be 0.
+ *
+ * There may also be driver-dependent minimum values for the number
+ * of entries per ring.
+ */
struct ethtool_ringparam {
- __u32 cmd; /* ETHTOOL_{G,S}RINGPARAM */
-
- /* Read only attributes. These indicate the maximum number
- * of pending RX/TX ring entries the driver will allow the
- * user to set.
- */
+ __u32 cmd;
__u32 rx_max_pending;
__u32 rx_mini_max_pending;
__u32 rx_jumbo_max_pending;
__u32 tx_max_pending;
-
- /* Values changeable by the user. The valid values are
- * in the range 1 to the "*_max_pending" counterpart above.
- */
__u32 rx_pending;
__u32 rx_mini_pending;
__u32 rx_jumbo_pending;
__u32 combined_count;
};
-/* for configuring link flow control parameters */
+/**
+ * struct ethtool_pauseparam - Ethernet pause (flow control) parameters
+ * @cmd: Command number = %ETHTOOL_GPAUSEPARAM or %ETHTOOL_SPAUSEPARAM
+ * @autoneg: Flag to enable autonegotiation of pause frame use
+ * @rx_pause: Flag to enable reception of pause frames
+ * @tx_pause: Flag to enable transmission of pause frames
+ *
+ * Drivers should reject a non-zero setting of @autoneg when
+ * autoneogotiation is disabled (or not supported) for the link.
+ *
+ * If the link is autonegotiated, drivers should use
+ * mii_advertise_flowctrl() or similar code to set the advertised
+ * pause frame capabilities based on the @rx_pause and @tx_pause flags,
+ * even if @autoneg is zero. They should also allow the advertised
+ * pause frame capabilities to be controlled directly through the
+ * advertising field of &struct ethtool_cmd.
+ *
+ * If @autoneg is non-zero, the MAC is configured to send and/or
+ * receive pause frames according to the result of autonegotiation.
+ * Otherwise, it is configured directly based on the @rx_pause and
+ * @tx_pause flags.
+ */
struct ethtool_pauseparam {
- __u32 cmd; /* ETHTOOL_{G,S}PAUSEPARAM */
-
- /* If the link is being auto-negotiated (via ethtool_cmd.autoneg
- * being true) the user may set 'autoneg' here non-zero to have the
- * pause parameters be auto-negotiated too. In such a case, the
- * {rx,tx}_pause values below determine what capabilities are
- * advertised.
- *
- * If 'autoneg' is zero or the link is not being auto-negotiated,
- * then {rx,tx}_pause force the driver to use/not-use pause
- * flow control.
- */
+ __u32 cmd;
__u32 autoneg;
__u32 rx_pause;
__u32 tx_pause;
};
#define ETH_GSTRING_LEN 32
+
+/**
+ * enum ethtool_stringset - string set ID
+ * @ETH_SS_TEST: Self-test result names, for use with %ETHTOOL_TEST
+ * @ETH_SS_STATS: Statistic names, for use with %ETHTOOL_GSTATS
+ * @ETH_SS_PRIV_FLAGS: Driver private flag names, for use with
+ * %ETHTOOL_GPFLAGS and %ETHTOOL_SPFLAGS
+ * @ETH_SS_NTUPLE_FILTERS: Previously used with %ETHTOOL_GRXNTUPLE;
+ * now deprecated
+ * @ETH_SS_FEATURES: Device feature names
+ * @ETH_SS_RSS_HASH_FUNCS: RSS hush function names
+ * @ETH_SS_PHY_STATS: Statistic names, for use with %ETHTOOL_GPHYSTATS
+ */
enum ethtool_stringset {
ETH_SS_TEST = 0,
ETH_SS_STATS,
ETH_SS_PRIV_FLAGS,
- ETH_SS_NTUPLE_FILTERS, /* Do not use, GRXNTUPLE is now deprecated */
+ ETH_SS_NTUPLE_FILTERS,
ETH_SS_FEATURES,
+ ETH_SS_RSS_HASH_FUNCS,
+ ETH_SS_TUNABLES,
+ ETH_SS_PHY_STATS,
};
-/* for passing string sets for data tagging */
+/**
+ * struct ethtool_gstrings - string set for data tagging
+ * @cmd: Command number = %ETHTOOL_GSTRINGS
+ * @string_set: String set ID; one of &enum ethtool_stringset
+ * @len: On return, the number of strings in the string set
+ * @data: Buffer for strings. Each string is null-padded to a size of
+ * %ETH_GSTRING_LEN.
+ *
+ * Users must use %ETHTOOL_GSSET_INFO to find the number of strings in
+ * the string set. They must allocate a buffer of the appropriate
+ * size immediately following this structure.
+ */
struct ethtool_gstrings {
- __u32 cmd; /* ETHTOOL_GSTRINGS */
- __u32 string_set; /* string set id e.c. ETH_SS_TEST, etc*/
- __u32 len; /* number of strings in the string set */
+ __u32 cmd;
+ __u32 string_set;
+ __u32 len;
__u8 data[0];
};
+/**
+ * struct ethtool_sset_info - string set information
+ * @cmd: Command number = %ETHTOOL_GSSET_INFO
+ * @sset_mask: On entry, a bitmask of string sets to query, with bits
+ * numbered according to &enum ethtool_stringset. On return, a
+ * bitmask of those string sets queried that are supported.
+ * @data: Buffer for string set sizes. On return, this contains the
+ * size of each string set that was queried and supported, in
+ * order of ID.
+ *
+ * Example: The user passes in @sset_mask = 0x7 (sets 0, 1, 2) and on
+ * return @sset_mask == 0x6 (sets 1, 2). Then @data[0] contains the
+ * size of set 1 and @data[1] contains the size of set 2.
+ *
+ * Users must allocate a buffer of the appropriate size (4 * number of
+ * sets queried) immediately following this structure.
+ */
struct ethtool_sset_info {
- __u32 cmd; /* ETHTOOL_GSSET_INFO */
+ __u32 cmd;
__u32 reserved;
- __u64 sset_mask; /* input: each bit selects an sset to query */
- /* output: each bit a returned sset */
- __u32 data[0]; /* ETH_SS_xxx count, in order, based on bits
- in sset_mask. One bit implies one
- __u32, two bits implies two
- __u32's, etc. */
+ __u64 sset_mask;
+ __u32 data[0];
};
/**
ETH_TEST_FL_EXTERNAL_LB_DONE = (1 << 3),
};
-/* for requesting NIC test and getting results*/
+/**
+ * struct ethtool_test - device self-test invocation
+ * @cmd: Command number = %ETHTOOL_TEST
+ * @flags: A bitmask of flags from &enum ethtool_test_flags. Some
+ * flags may be set by the user on entry; others may be set by
+ * the driver on return.
+ * @len: On return, the number of test results
+ * @data: Array of test results
+ *
+ * Users must use %ETHTOOL_GSSET_INFO or %ETHTOOL_GDRVINFO to find the
+ * number of test results that will be returned. They must allocate a
+ * buffer of the appropriate size (8 * number of results) immediately
+ * following this structure.
+ */
struct ethtool_test {
- __u32 cmd; /* ETHTOOL_TEST */
- __u32 flags; /* ETH_TEST_FL_xxx */
+ __u32 cmd;
+ __u32 flags;
__u32 reserved;
- __u32 len; /* result length, in number of u64 elements */
+ __u32 len;
__u64 data[0];
};
-/* for dumping NIC-specific statistics */
+/**
+ * struct ethtool_stats - device-specific statistics
+ * @cmd: Command number = %ETHTOOL_GSTATS
+ * @n_stats: On return, the number of statistics
+ * @data: Array of statistics
+ *
+ * Users must use %ETHTOOL_GSSET_INFO or %ETHTOOL_GDRVINFO to find the
+ * number of statistics that will be returned. They must allocate a
+ * buffer of the appropriate size (8 * number of statistics)
+ * immediately following this structure.
+ */
struct ethtool_stats {
- __u32 cmd; /* ETHTOOL_GSTATS */
- __u32 n_stats; /* number of u64's being returned */
+ __u32 cmd;
+ __u32 n_stats;
__u64 data[0];
};
+/**
+ * struct ethtool_perm_addr - permanent hardware address
+ * @cmd: Command number = %ETHTOOL_GPERMADDR
+ * @size: On entry, the size of the buffer. On return, the size of the
+ * address. The command fails if the buffer is too small.
+ * @data: Buffer for the address
+ *
+ * Users must allocate the buffer immediately following this structure.
+ * A buffer size of %MAX_ADDR_LEN should be sufficient for any address
+ * type.
+ */
struct ethtool_perm_addr {
- __u32 cmd; /* ETHTOOL_GPERMADDR */
+ __u32 cmd;
__u32 size;
__u8 data[0];
};
__u8 proto;
};
+/**
+ * struct ethtool_tcpip6_spec - flow specification for TCP/IPv6 etc.
+ * @ip6src: Source host
+ * @ip6dst: Destination host
+ * @psrc: Source port
+ * @pdst: Destination port
+ * @tclass: Traffic Class
+ *
+ * This can be used to specify a TCP/IPv6, UDP/IPv6 or SCTP/IPv6 flow.
+ */
+struct ethtool_tcpip6_spec {
+ __be32 ip6src[4];
+ __be32 ip6dst[4];
+ __be16 psrc;
+ __be16 pdst;
+ __u8 tclass;
+};
+
+/**
+ * struct ethtool_ah_espip6_spec - flow specification for IPsec/IPv6
+ * @ip6src: Source host
+ * @ip6dst: Destination host
+ * @spi: Security parameters index
+ * @tclass: Traffic Class
+ *
+ * This can be used to specify an IPsec transport or tunnel over IPv6.
+ */
+struct ethtool_ah_espip6_spec {
+ __be32 ip6src[4];
+ __be32 ip6dst[4];
+ __be32 spi;
+ __u8 tclass;
+};
+
+/**
+ * struct ethtool_usrip6_spec - general flow specification for IPv6
+ * @ip6src: Source host
+ * @ip6dst: Destination host
+ * @l4_4_bytes: First 4 bytes of transport (layer 4) header
+ * @tclass: Traffic Class
+ * @l4_proto: Transport protocol number (nexthdr after any Extension Headers)
+ */
+struct ethtool_usrip6_spec {
+ __be32 ip6src[4];
+ __be32 ip6dst[4];
+ __be32 l4_4_bytes;
+ __u8 tclass;
+ __u8 l4_proto;
+};
+
union ethtool_flow_union {
struct ethtool_tcpip4_spec tcp_ip4_spec;
struct ethtool_tcpip4_spec udp_ip4_spec;
struct ethtool_ah_espip4_spec ah_ip4_spec;
struct ethtool_ah_espip4_spec esp_ip4_spec;
struct ethtool_usrip4_spec usr_ip4_spec;
+ struct ethtool_tcpip6_spec tcp_ip6_spec;
+ struct ethtool_tcpip6_spec udp_ip6_spec;
+ struct ethtool_tcpip6_spec sctp_ip6_spec;
+ struct ethtool_ah_espip6_spec ah_ip6_spec;
+ struct ethtool_ah_espip6_spec esp_ip6_spec;
+ struct ethtool_usrip6_spec usr_ip6_spec;
struct ethhdr ether_spec;
- __u8 hdata[60];
+ __u8 hdata[52];
};
+/**
+ * struct ethtool_flow_ext - additional RX flow fields
+ * @h_dest: destination MAC address
+ * @vlan_etype: VLAN EtherType
+ * @vlan_tci: VLAN tag control information
+ * @data: user defined data
+ *
+ * Note, @vlan_etype, @vlan_tci, and @data are only valid if %FLOW_EXT
+ * is set in &struct ethtool_rx_flow_spec @flow_type.
+ * @h_dest is valid if %FLOW_MAC_EXT is set.
+ */
struct ethtool_flow_ext {
- __be16 vlan_etype;
- __be16 vlan_tci;
- __be32 data[2];
+ __u8 padding[2];
+ unsigned char h_dest[ETH_ALEN];
+ __be16 vlan_etype;
+ __be16 vlan_tci;
+ __be32 data[2];
};
/**
* @m_u: Masks for flow field bits to be matched
* @m_ext: Masks for additional field bits to be matched
* Note, all additional fields must be ignored unless @flow_type
- * includes the %FLOW_EXT flag.
+ * includes the %FLOW_EXT or %FLOW_MAC_EXT flag
+ * (see &struct ethtool_flow_ext description).
* @ring_cookie: RX ring/queue index to deliver to, or %RX_CLS_FLOW_DISC
* if packets should be discarded
* @location: Location of rule in the table. Locations must be
__u32 location;
};
+/* How rings are layed out when accessing virtual functions or
+ * offloaded queues is device specific. To allow users to do flow
+ * steering and specify these queues the ring cookie is partitioned
+ * into a 32bit queue index with an 8 bit virtual function id.
+ * This also leaves the 3bytes for further specifiers. It is possible
+ * future devices may support more than 256 virtual functions if
+ * devices start supporting PCIe w/ARI. However at the moment I
+ * do not know of any devices that support this so I do not reserve
+ * space for this at this time. If a future patch consumes the next
+ * byte it should be aware of this possiblity.
+ */
+#define ETHTOOL_RX_FLOW_SPEC_RING 0x00000000FFFFFFFFLL
+#define ETHTOOL_RX_FLOW_SPEC_RING_VF 0x000000FF00000000LL
+#define ETHTOOL_RX_FLOW_SPEC_RING_VF_OFF 32
+static inline __u64 ethtool_get_flow_spec_ring(__u64 ring_cookie)
+{
+ return ETHTOOL_RX_FLOW_SPEC_RING & ring_cookie;
+};
+
+static inline __u64 ethtool_get_flow_spec_ring_vf(__u64 ring_cookie)
+{
+ return (ETHTOOL_RX_FLOW_SPEC_RING_VF & ring_cookie) >>
+ ETHTOOL_RX_FLOW_SPEC_RING_VF_OFF;
+};
+
/**
* struct ethtool_rxnfc - command to get or set RX flow classification rules
* @cmd: Specific command number - %ETHTOOL_GRXFH, %ETHTOOL_SRXFH,
* %ETHTOOL_SRXCLSRLINS may add the rule at any suitable unused
* location, and may remove a rule at a later location (lower
* priority) that matches exactly the same set of flows. The special
- * values are: %RX_CLS_LOC_ANY, selecting any location;
+ * values are %RX_CLS_LOC_ANY, selecting any location;
* %RX_CLS_LOC_FIRST, selecting the first suitable location (maximum
* priority); and %RX_CLS_LOC_LAST, selecting the last suitable
* location (minimum priority). Additional special values may be
__u32 ring_index[0];
};
+/**
+ * struct ethtool_rxfh - command to get/set RX flow hash indir or/and hash key.
+ * @cmd: Specific command number - %ETHTOOL_GRSSH or %ETHTOOL_SRSSH
+ * @rss_context: RSS context identifier.
+ * @indir_size: On entry, the array size of the user buffer for the
+ * indirection table, which may be zero, or (for %ETHTOOL_SRSSH),
+ * %ETH_RXFH_INDIR_NO_CHANGE. On return from %ETHTOOL_GRSSH,
+ * the array size of the hardware indirection table.
+ * @key_size: On entry, the array size of the user buffer for the hash key,
+ * which may be zero. On return from %ETHTOOL_GRSSH, the size of the
+ * hardware hash key.
+ * @hfunc: Defines the current RSS hash function used by HW (or to be set to).
+ * Valid values are one of the %ETH_RSS_HASH_*.
+ * @rsvd: Reserved for future extensions.
+ * @rss_config: RX ring/queue index for each hash value i.e., indirection table
+ * of @indir_size __u32 elements, followed by hash key of @key_size
+ * bytes.
+ *
+ * For %ETHTOOL_GRSSH, a @indir_size and key_size of zero means that only the
+ * size should be returned. For %ETHTOOL_SRSSH, an @indir_size of
+ * %ETH_RXFH_INDIR_NO_CHANGE means that indir table setting is not requested
+ * and a @indir_size of zero means the indir table should be reset to default
+ * values. An hfunc of zero means that hash function setting is not requested.
+ */
+struct ethtool_rxfh {
+ __u32 cmd;
+ __u32 rss_context;
+ __u32 indir_size;
+ __u32 key_size;
+ __u8 hfunc;
+ __u8 rsvd8[3];
+ __u32 rsvd32;
+ __u32 rss_config[0];
+};
+#define ETH_RXFH_INDIR_NO_CHANGE 0xffffffff
+
/**
* struct ethtool_rx_ntuple_flow_spec - specification for RX flow filter
* @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW
* for %ETHTOOL_GET_DUMP_FLAG command
* @data: data collected for get dump data operation
*/
-
-#define ETH_FW_DUMP_DISABLE 0
-
struct ethtool_dump {
__u32 cmd;
__u32 version;
__u8 data[0];
};
+#define ETH_FW_DUMP_DISABLE 0
+
/* for returning and changing feature sets */
/**
/**
* struct ethtool_gfeatures - command to get state of device's features
* @cmd: command number = %ETHTOOL_GFEATURES
- * @size: in: number of elements in the features[] array;
- * out: number of elements in features[] needed to hold all features
+ * @size: On entry, the number of elements in the features[] array;
+ * on return, the number of elements in features[] needed to hold
+ * all features
* @features: state of features
*/
struct ethtool_gfeatures {
* the 'hwtstamp_tx_types' and 'hwtstamp_rx_filters' enumeration values,
* respectively. For example, if the device supports HWTSTAMP_TX_ON,
* then (1 << HWTSTAMP_TX_ON) in 'tx_types' will be set.
+ *
+ * Drivers should only report the filters they actually support without
+ * upscaling in the SIOCSHWTSTAMP ioctl. If the SIOCSHWSTAMP request for
+ * HWTSTAMP_FILTER_V1_SYNC is supported by HWTSTAMP_FILTER_V1_EVENT, then the
+ * driver should only report HWTSTAMP_FILTER_V1_EVENT in this op.
*/
struct ethtool_ts_info {
__u32 cmd;
#define ETHTOOL_F_WISH (1 << ETHTOOL_F_WISH__BIT)
#define ETHTOOL_F_COMPAT (1 << ETHTOOL_F_COMPAT__BIT)
+#define MAX_NUM_QUEUE 4096
+
+#if 0
+/**
+ * struct ethtool_per_queue_op - apply sub command to the queues in mask.
+ * @cmd: ETHTOOL_PERQUEUE
+ * @sub_command: the sub command which apply to each queues
+ * @queue_mask: Bitmap of the queues which sub command apply to
+ * @data: A complete command structure following for each of the queues addressed
+ */
+struct ethtool_per_queue_op {
+ __u32 cmd;
+ __u32 sub_command;
+ __u32 queue_mask[__KERNEL_DIV_ROUND_UP(MAX_NUM_QUEUE, 32)];
+ char data[];
+};
+#endif
/* CMDs currently supported */
-#define ETHTOOL_GSET 0x00000001 /* Get settings. */
-#define ETHTOOL_SSET 0x00000002 /* Set settings. */
+#define ETHTOOL_GSET 0x00000001 /* DEPRECATED, Get settings.
+ * Please use ETHTOOL_GLINKSETTINGS
+ */
+#define ETHTOOL_SSET 0x00000002 /* DEPRECATED, Set settings.
+ * Please use ETHTOOL_SLINKSETTINGS
+ */
#define ETHTOOL_GDRVINFO 0x00000003 /* Get driver info. */
#define ETHTOOL_GREGS 0x00000004 /* Get NIC registers. */
#define ETHTOOL_GWOL 0x00000005 /* Get wake-on-lan options. */
#define ETHTOOL_GEEE 0x00000044 /* Get EEE settings */
#define ETHTOOL_SEEE 0x00000045 /* Set EEE settings */
+#define ETHTOOL_GRSSH 0x00000046 /* Get RX flow hash configuration */
+#define ETHTOOL_SRSSH 0x00000047 /* Set RX flow hash configuration */
+#define ETHTOOL_GTUNABLE 0x00000048 /* Get tunable configuration */
+#define ETHTOOL_STUNABLE 0x00000049 /* Set tunable configuration */
+#define ETHTOOL_GPHYSTATS 0x0000004a /* get PHY-specific statistics */
+
+#define ETHTOOL_PERQUEUE 0x0000004b /* Set per queue options */
+
+#define ETHTOOL_GLINKSETTINGS 0x0000004c /* Get ethtool_link_settings */
+#define ETHTOOL_SLINKSETTINGS 0x0000004d /* Set ethtool_link_settings */
+
+
/* compatibility with older code */
#define SPARC_ETH_GSET ETHTOOL_GSET
#define SPARC_ETH_SSET ETHTOOL_SSET
-/* Indicates what features are supported by the interface. */
-#define SUPPORTED_10baseT_Half (1 << 0)
-#define SUPPORTED_10baseT_Full (1 << 1)
-#define SUPPORTED_100baseT_Half (1 << 2)
-#define SUPPORTED_100baseT_Full (1 << 3)
-#define SUPPORTED_1000baseT_Half (1 << 4)
-#define SUPPORTED_1000baseT_Full (1 << 5)
-#define SUPPORTED_Autoneg (1 << 6)
-#define SUPPORTED_TP (1 << 7)
-#define SUPPORTED_AUI (1 << 8)
-#define SUPPORTED_MII (1 << 9)
-#define SUPPORTED_FIBRE (1 << 10)
-#define SUPPORTED_BNC (1 << 11)
-#define SUPPORTED_10000baseT_Full (1 << 12)
-#define SUPPORTED_Pause (1 << 13)
-#define SUPPORTED_Asym_Pause (1 << 14)
-#define SUPPORTED_2500baseX_Full (1 << 15)
-#define SUPPORTED_Backplane (1 << 16)
-#define SUPPORTED_1000baseKX_Full (1 << 17)
-#define SUPPORTED_10000baseKX4_Full (1 << 18)
-#define SUPPORTED_10000baseKR_Full (1 << 19)
-#define SUPPORTED_10000baseR_FEC (1 << 20)
-#define SUPPORTED_20000baseMLD2_Full (1 << 21)
-#define SUPPORTED_20000baseKR2_Full (1 << 22)
-#define SUPPORTED_40000baseKR4_Full (1 << 23)
-#define SUPPORTED_40000baseCR4_Full (1 << 24)
-#define SUPPORTED_40000baseSR4_Full (1 << 25)
-#define SUPPORTED_40000baseLR4_Full (1 << 26)
-
-/* Indicates what features are advertised by the interface. */
-#define ADVERTISED_10baseT_Half (1 << 0)
-#define ADVERTISED_10baseT_Full (1 << 1)
-#define ADVERTISED_100baseT_Half (1 << 2)
-#define ADVERTISED_100baseT_Full (1 << 3)
-#define ADVERTISED_1000baseT_Half (1 << 4)
-#define ADVERTISED_1000baseT_Full (1 << 5)
-#define ADVERTISED_Autoneg (1 << 6)
-#define ADVERTISED_TP (1 << 7)
-#define ADVERTISED_AUI (1 << 8)
-#define ADVERTISED_MII (1 << 9)
-#define ADVERTISED_FIBRE (1 << 10)
-#define ADVERTISED_BNC (1 << 11)
-#define ADVERTISED_10000baseT_Full (1 << 12)
-#define ADVERTISED_Pause (1 << 13)
-#define ADVERTISED_Asym_Pause (1 << 14)
-#define ADVERTISED_2500baseX_Full (1 << 15)
-#define ADVERTISED_Backplane (1 << 16)
-#define ADVERTISED_1000baseKX_Full (1 << 17)
-#define ADVERTISED_10000baseKX4_Full (1 << 18)
-#define ADVERTISED_10000baseKR_Full (1 << 19)
-#define ADVERTISED_10000baseR_FEC (1 << 20)
-#define ADVERTISED_20000baseMLD2_Full (1 << 21)
-#define ADVERTISED_20000baseKR2_Full (1 << 22)
-#define ADVERTISED_40000baseKR4_Full (1 << 23)
-#define ADVERTISED_40000baseCR4_Full (1 << 24)
-#define ADVERTISED_40000baseSR4_Full (1 << 25)
-#define ADVERTISED_40000baseLR4_Full (1 << 26)
+/* Link mode bit indices */
+enum ethtool_link_mode_bit_indices {
+ ETHTOOL_LINK_MODE_10baseT_Half_BIT = 0,
+ ETHTOOL_LINK_MODE_10baseT_Full_BIT = 1,
+ ETHTOOL_LINK_MODE_100baseT_Half_BIT = 2,
+ ETHTOOL_LINK_MODE_100baseT_Full_BIT = 3,
+ ETHTOOL_LINK_MODE_1000baseT_Half_BIT = 4,
+ ETHTOOL_LINK_MODE_1000baseT_Full_BIT = 5,
+ ETHTOOL_LINK_MODE_Autoneg_BIT = 6,
+ ETHTOOL_LINK_MODE_TP_BIT = 7,
+ ETHTOOL_LINK_MODE_AUI_BIT = 8,
+ ETHTOOL_LINK_MODE_MII_BIT = 9,
+ ETHTOOL_LINK_MODE_FIBRE_BIT = 10,
+ ETHTOOL_LINK_MODE_BNC_BIT = 11,
+ ETHTOOL_LINK_MODE_10000baseT_Full_BIT = 12,
+ ETHTOOL_LINK_MODE_Pause_BIT = 13,
+ ETHTOOL_LINK_MODE_Asym_Pause_BIT = 14,
+ ETHTOOL_LINK_MODE_2500baseX_Full_BIT = 15,
+ ETHTOOL_LINK_MODE_Backplane_BIT = 16,
+ ETHTOOL_LINK_MODE_1000baseKX_Full_BIT = 17,
+ ETHTOOL_LINK_MODE_10000baseKX4_Full_BIT = 18,
+ ETHTOOL_LINK_MODE_10000baseKR_Full_BIT = 19,
+ ETHTOOL_LINK_MODE_10000baseR_FEC_BIT = 20,
+ ETHTOOL_LINK_MODE_20000baseMLD2_Full_BIT = 21,
+ ETHTOOL_LINK_MODE_20000baseKR2_Full_BIT = 22,
+ ETHTOOL_LINK_MODE_40000baseKR4_Full_BIT = 23,
+ ETHTOOL_LINK_MODE_40000baseCR4_Full_BIT = 24,
+ ETHTOOL_LINK_MODE_40000baseSR4_Full_BIT = 25,
+ ETHTOOL_LINK_MODE_40000baseLR4_Full_BIT = 26,
+ ETHTOOL_LINK_MODE_56000baseKR4_Full_BIT = 27,
+ ETHTOOL_LINK_MODE_56000baseCR4_Full_BIT = 28,
+ ETHTOOL_LINK_MODE_56000baseSR4_Full_BIT = 29,
+ ETHTOOL_LINK_MODE_56000baseLR4_Full_BIT = 30,
+ ETHTOOL_LINK_MODE_25000baseCR_Full_BIT = 31,
+ ETHTOOL_LINK_MODE_25000baseKR_Full_BIT = 32,
+ ETHTOOL_LINK_MODE_25000baseSR_Full_BIT = 33,
+ ETHTOOL_LINK_MODE_50000baseCR2_Full_BIT = 34,
+ ETHTOOL_LINK_MODE_50000baseKR2_Full_BIT = 35,
+ ETHTOOL_LINK_MODE_100000baseKR4_Full_BIT = 36,
+ ETHTOOL_LINK_MODE_100000baseSR4_Full_BIT = 37,
+ ETHTOOL_LINK_MODE_100000baseCR4_Full_BIT = 38,
+ ETHTOOL_LINK_MODE_100000baseLR4_ER4_Full_BIT = 39,
+
+ /* Last allowed bit for __ETHTOOL_LINK_MODE_LEGACY_MASK is bit
+ * 31. Please do NOT define any SUPPORTED_* or ADVERTISED_*
+ * macro for bits > 31. The only way to use indices > 31 is to
+ * use the new ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API.
+ */
+
+ __ETHTOOL_LINK_MODE_LAST
+ = ETHTOOL_LINK_MODE_100000baseLR4_ER4_Full_BIT,
+};
+
+#define __ETHTOOL_LINK_MODE_LEGACY_MASK(base_name) \
+ (1UL << (ETHTOOL_LINK_MODE_ ## base_name ## _BIT))
+
+/* DEPRECATED macros. Please migrate to
+ * ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. Please do NOT
+ * define any new SUPPORTED_* macro for bits > 31.
+ */
+#define SUPPORTED_10baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Half)
+#define SUPPORTED_10baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Full)
+#define SUPPORTED_100baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Half)
+#define SUPPORTED_100baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Full)
+#define SUPPORTED_1000baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Half)
+#define SUPPORTED_1000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Full)
+#define SUPPORTED_Autoneg __ETHTOOL_LINK_MODE_LEGACY_MASK(Autoneg)
+#define SUPPORTED_TP __ETHTOOL_LINK_MODE_LEGACY_MASK(TP)
+#define SUPPORTED_AUI __ETHTOOL_LINK_MODE_LEGACY_MASK(AUI)
+#define SUPPORTED_MII __ETHTOOL_LINK_MODE_LEGACY_MASK(MII)
+#define SUPPORTED_FIBRE __ETHTOOL_LINK_MODE_LEGACY_MASK(FIBRE)
+#define SUPPORTED_BNC __ETHTOOL_LINK_MODE_LEGACY_MASK(BNC)
+#define SUPPORTED_10000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseT_Full)
+#define SUPPORTED_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Pause)
+#define SUPPORTED_Asym_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Asym_Pause)
+#define SUPPORTED_2500baseX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(2500baseX_Full)
+#define SUPPORTED_Backplane __ETHTOOL_LINK_MODE_LEGACY_MASK(Backplane)
+#define SUPPORTED_1000baseKX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseKX_Full)
+#define SUPPORTED_10000baseKX4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKX4_Full)
+#define SUPPORTED_10000baseKR_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKR_Full)
+#define SUPPORTED_10000baseR_FEC __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseR_FEC)
+#define SUPPORTED_20000baseMLD2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseMLD2_Full)
+#define SUPPORTED_20000baseKR2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseKR2_Full)
+#define SUPPORTED_40000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseKR4_Full)
+#define SUPPORTED_40000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseCR4_Full)
+#define SUPPORTED_40000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseSR4_Full)
+#define SUPPORTED_40000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseLR4_Full)
+#define SUPPORTED_56000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseKR4_Full)
+#define SUPPORTED_56000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseCR4_Full)
+#define SUPPORTED_56000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseSR4_Full)
+#define SUPPORTED_56000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseLR4_Full)
+/* Please do not define any new SUPPORTED_* macro for bits > 31, see
+ * notice above.
+ */
+
+/*
+ * DEPRECATED macros. Please migrate to
+ * ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. Please do NOT
+ * define any new ADERTISE_* macro for bits > 31.
+ */
+#define ADVERTISED_10baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Half)
+#define ADVERTISED_10baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Full)
+#define ADVERTISED_100baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Half)
+#define ADVERTISED_100baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Full)
+#define ADVERTISED_1000baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Half)
+#define ADVERTISED_1000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Full)
+#define ADVERTISED_Autoneg __ETHTOOL_LINK_MODE_LEGACY_MASK(Autoneg)
+#define ADVERTISED_TP __ETHTOOL_LINK_MODE_LEGACY_MASK(TP)
+#define ADVERTISED_AUI __ETHTOOL_LINK_MODE_LEGACY_MASK(AUI)
+#define ADVERTISED_MII __ETHTOOL_LINK_MODE_LEGACY_MASK(MII)
+#define ADVERTISED_FIBRE __ETHTOOL_LINK_MODE_LEGACY_MASK(FIBRE)
+#define ADVERTISED_BNC __ETHTOOL_LINK_MODE_LEGACY_MASK(BNC)
+#define ADVERTISED_10000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseT_Full)
+#define ADVERTISED_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Pause)
+#define ADVERTISED_Asym_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Asym_Pause)
+#define ADVERTISED_2500baseX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(2500baseX_Full)
+#define ADVERTISED_Backplane __ETHTOOL_LINK_MODE_LEGACY_MASK(Backplane)
+#define ADVERTISED_1000baseKX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseKX_Full)
+#define ADVERTISED_10000baseKX4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKX4_Full)
+#define ADVERTISED_10000baseKR_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKR_Full)
+#define ADVERTISED_10000baseR_FEC __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseR_FEC)
+#define ADVERTISED_20000baseMLD2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseMLD2_Full)
+#define ADVERTISED_20000baseKR2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseKR2_Full)
+#define ADVERTISED_40000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseKR4_Full)
+#define ADVERTISED_40000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseCR4_Full)
+#define ADVERTISED_40000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseSR4_Full)
+#define ADVERTISED_40000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseLR4_Full)
+#define ADVERTISED_56000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseKR4_Full)
+#define ADVERTISED_56000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseCR4_Full)
+#define ADVERTISED_56000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseSR4_Full)
+#define ADVERTISED_56000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseLR4_Full)
+/* Please do not define any new ADVERTISED_* macro for bits > 31, see
+ * notice above.
+ */
/* The following are all involved in forcing a particular link
* mode for the device for setting things. When getting the
* it was forced up into this mode or autonegotiated.
*/
-/* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */
+/* The forced speed, in units of 1Mb. All values 0 to INT_MAX are legal. */
#define SPEED_10 10
#define SPEED_100 100
#define SPEED_1000 1000
#define SPEED_2500 2500
+#define SPEED_5000 5000
#define SPEED_10000 10000
+#define SPEED_20000 20000
+#define SPEED_25000 25000
+#define SPEED_40000 40000
+#define SPEED_50000 50000
+#define SPEED_56000 56000
+#define SPEED_100000 100000
+
#define SPEED_UNKNOWN -1
+static inline int ethtool_validate_speed(__u32 speed)
+{
+ return speed <= INT_MAX || speed == SPEED_UNKNOWN;
+}
+
/* Duplex, half or full. */
#define DUPLEX_HALF 0x00
#define DUPLEX_FULL 0x01
#define DUPLEX_UNKNOWN 0xff
+static inline int ethtool_validate_duplex(__u8 duplex)
+{
+ switch (duplex) {
+ case DUPLEX_HALF:
+ case DUPLEX_FULL:
+ case DUPLEX_UNKNOWN:
+ return 1;
+ }
+
+ return 0;
+}
+
/* Which connector port. */
#define PORT_TP 0x00
#define PORT_AUI 0x01
#define PORT_OTHER 0xff
/* Which transceiver to use. */
-#define XCVR_INTERNAL 0x00
-#define XCVR_EXTERNAL 0x01
+#define XCVR_INTERNAL 0x00 /* PHY and MAC are in the same package */
+#define XCVR_EXTERNAL 0x01 /* PHY and MAC are in different packages */
#define XCVR_DUMMY1 0x02
#define XCVR_DUMMY2 0x03
#define XCVR_DUMMY3 0x04
-/* Enable or disable autonegotiation. If this is set to enable,
- * the forced link modes above are completely ignored.
- */
+/* Enable or disable autonegotiation. */
#define AUTONEG_DISABLE 0x00
#define AUTONEG_ENABLE 0x01
-/* Mode MDI or MDI-X */
-#define ETH_TP_MDI_INVALID 0x00
-#define ETH_TP_MDI 0x01
-#define ETH_TP_MDI_X 0x02
+/* MDI or MDI-X status/control - if MDI/MDI_X/AUTO is set then
+ * the driver is required to renegotiate link
+ */
+#define ETH_TP_MDI_INVALID 0x00 /* status: unknown; control: unsupported */
+#define ETH_TP_MDI 0x01 /* status: MDI; control: force MDI */
+#define ETH_TP_MDI_X 0x02 /* status: MDI-X; control: force MDI-X */
+#define ETH_TP_MDI_AUTO 0x03 /* control: auto-select */
/* Wake-On-Lan options. */
#define WAKE_PHY (1 << 0)
#define UDP_V4_FLOW 0x02 /* hash or spec (udp_ip4_spec) */
#define SCTP_V4_FLOW 0x03 /* hash or spec (sctp_ip4_spec) */
#define AH_ESP_V4_FLOW 0x04 /* hash only */
-#define TCP_V6_FLOW 0x05 /* hash only */
-#define UDP_V6_FLOW 0x06 /* hash only */
-#define SCTP_V6_FLOW 0x07 /* hash only */
+#define TCP_V6_FLOW 0x05 /* hash or spec (tcp_ip6_spec; nfc only) */
+#define UDP_V6_FLOW 0x06 /* hash or spec (udp_ip6_spec; nfc only) */
+#define SCTP_V6_FLOW 0x07 /* hash or spec (sctp_ip6_spec; nfc only) */
#define AH_ESP_V6_FLOW 0x08 /* hash only */
#define AH_V4_FLOW 0x09 /* hash or spec (ah_ip4_spec) */
#define ESP_V4_FLOW 0x0a /* hash or spec (esp_ip4_spec) */
-#define AH_V6_FLOW 0x0b /* hash only */
-#define ESP_V6_FLOW 0x0c /* hash only */
-#define IP_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */
+#define AH_V6_FLOW 0x0b /* hash or spec (ah_ip6_spec; nfc only) */
+#define ESP_V6_FLOW 0x0c /* hash or spec (esp_ip6_spec; nfc only) */
+#define IPV4_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */
+#define IP_USER_FLOW IPV4_USER_FLOW
+#define IPV6_USER_FLOW 0x0e /* spec only (usr_ip6_spec; nfc only) */
#define IPV4_FLOW 0x10 /* hash only */
#define IPV6_FLOW 0x11 /* hash only */
#define ETHER_FLOW 0x12 /* spec only (ether_spec) */
/* Flag to enable additional fields in struct ethtool_rx_flow_spec */
#define FLOW_EXT 0x80000000
+#define FLOW_MAC_EXT 0x40000000
/* L3-L4 network traffic flow hash options */
#define RXH_L2DA (1 << 1)
#define ETH_MODULE_SFF_8079_LEN 256
#define ETH_MODULE_SFF_8472 0x2
#define ETH_MODULE_SFF_8472_LEN 512
+#define ETH_MODULE_SFF_8636 0x3
+#define ETH_MODULE_SFF_8636_LEN 256
+#define ETH_MODULE_SFF_8436 0x4
+#define ETH_MODULE_SFF_8436_LEN 256
/* Reset flags */
/* The reset() operation must clear the flags for the components which
};
#define ETH_RESET_SHARED_SHIFT 16
-#endif /* _LINUX_ETHTOOL_H */
+
+/**
+ * struct ethtool_link_settings - link control and status
+ *
+ * IMPORTANT, Backward compatibility notice: When implementing new
+ * user-space tools, please first try %ETHTOOL_GLINKSETTINGS, and
+ * if it succeeds use %ETHTOOL_SLINKSETTINGS to change link
+ * settings; do not use %ETHTOOL_SSET if %ETHTOOL_GLINKSETTINGS
+ * succeeded: stick to %ETHTOOL_GLINKSETTINGS/%SLINKSETTINGS in
+ * that case. Conversely, if %ETHTOOL_GLINKSETTINGS fails, use
+ * %ETHTOOL_GSET to query and %ETHTOOL_SSET to change link
+ * settings; do not use %ETHTOOL_SLINKSETTINGS if
+ * %ETHTOOL_GLINKSETTINGS failed: stick to
+ * %ETHTOOL_GSET/%ETHTOOL_SSET in that case.
+ *
+ * @cmd: Command number = %ETHTOOL_GLINKSETTINGS or %ETHTOOL_SLINKSETTINGS
+ * @speed: Link speed (Mbps)
+ * @duplex: Duplex mode; one of %DUPLEX_*
+ * @port: Physical connector type; one of %PORT_*
+ * @phy_address: MDIO address of PHY (transceiver); 0 or 255 if not
+ * applicable. For clause 45 PHYs this is the PRTAD.
+ * @autoneg: Enable/disable autonegotiation and auto-detection;
+ * either %AUTONEG_DISABLE or %AUTONEG_ENABLE
+ * @mdio_support: Bitmask of %ETH_MDIO_SUPPORTS_* flags for the MDIO
+ * protocols supported by the interface; 0 if unknown.
+ * Read-only.
+ * @eth_tp_mdix: Ethernet twisted-pair MDI(-X) status; one of
+ * %ETH_TP_MDI_*. If the status is unknown or not applicable, the
+ * value will be %ETH_TP_MDI_INVALID. Read-only.
+ * @eth_tp_mdix_ctrl: Ethernet twisted pair MDI(-X) control; one of
+ * %ETH_TP_MDI_*. If MDI(-X) control is not implemented, reads
+ * yield %ETH_TP_MDI_INVALID and writes may be ignored or rejected.
+ * When written successfully, the link should be renegotiated if
+ * necessary.
+ * @link_mode_masks_nwords: Number of 32-bit words for each of the
+ * supported, advertising, lp_advertising link mode bitmaps. For
+ * %ETHTOOL_GLINKSETTINGS: on entry, number of words passed by user
+ * (>= 0); on return, if handshake in progress, negative if
+ * request size unsupported by kernel: absolute value indicates
+ * kernel expected size and all the other fields but cmd
+ * are 0; otherwise (handshake completed), strictly positive
+ * to indicate size used by kernel and cmd field stays
+ * %ETHTOOL_GLINKSETTINGS, all other fields populated by driver. For
+ * %ETHTOOL_SLINKSETTINGS: must be valid on entry, ie. a positive
+ * value returned previously by %ETHTOOL_GLINKSETTINGS, otherwise
+ * refused. For drivers: ignore this field (use kernel's
+ * __ETHTOOL_LINK_MODE_MASK_NBITS instead), any change to it will
+ * be overwritten by kernel.
+ * @supported: Bitmap with each bit meaning given by
+ * %ethtool_link_mode_bit_indices for the link modes, physical
+ * connectors and other link features for which the interface
+ * supports autonegotiation or auto-detection. Read-only.
+ * @advertising: Bitmap with each bit meaning given by
+ * %ethtool_link_mode_bit_indices for the link modes, physical
+ * connectors and other link features that are advertised through
+ * autonegotiation or enabled for auto-detection.
+ * @lp_advertising: Bitmap with each bit meaning given by
+ * %ethtool_link_mode_bit_indices for the link modes, and other
+ * link features that the link partner advertised through
+ * autonegotiation; 0 if unknown or not applicable. Read-only.
+ *
+ * If autonegotiation is disabled, the speed and @duplex represent the
+ * fixed link mode and are writable if the driver supports multiple
+ * link modes. If it is enabled then they are read-only; if the link
+ * is up they represent the negotiated link mode; if the link is down,
+ * the speed is 0, %SPEED_UNKNOWN or the highest enabled speed and
+ * @duplex is %DUPLEX_UNKNOWN or the best enabled duplex mode.
+ *
+ * Some hardware interfaces may have multiple PHYs and/or physical
+ * connectors fitted or do not allow the driver to detect which are
+ * fitted. For these interfaces @port and/or @phy_address may be
+ * writable, possibly dependent on @autoneg being %AUTONEG_DISABLE.
+ * Otherwise, attempts to write different values may be ignored or
+ * rejected.
+ *
+ * Deprecated %ethtool_cmd fields transceiver, maxtxpkt and maxrxpkt
+ * are not available in %ethtool_link_settings. Until all drivers are
+ * converted to ignore them or to the new %ethtool_link_settings API,
+ * for both queries and changes, users should always try
+ * %ETHTOOL_GLINKSETTINGS first, and if it fails with -ENOTSUPP stick
+ * only to %ETHTOOL_GSET and %ETHTOOL_SSET consistently. If it
+ * succeeds, then users should stick to %ETHTOOL_GLINKSETTINGS and
+ * %ETHTOOL_SLINKSETTINGS (which would support drivers implementing
+ * either %ethtool_cmd or %ethtool_link_settings).
+ *
+ * Users should assume that all fields not marked read-only are
+ * writable and subject to validation by the driver. They should use
+ * %ETHTOOL_GLINKSETTINGS to get the current values before making specific
+ * changes and then applying them with %ETHTOOL_SLINKSETTINGS.
+ *
+ * Drivers that implement %get_link_ksettings and/or
+ * %set_link_ksettings should ignore the @cmd
+ * and @link_mode_masks_nwords fields (any change to them overwritten
+ * by kernel), and rely only on kernel's internal
+ * %__ETHTOOL_LINK_MODE_MASK_NBITS and
+ * %ethtool_link_mode_mask_t. Drivers that implement
+ * %set_link_ksettings() should validate all fields other than @cmd
+ * and @link_mode_masks_nwords that are not described as read-only or
+ * deprecated, and must ignore all fields described as read-only.
+ */
+struct ethtool_link_settings {
+ __u32 cmd;
+ __u32 speed;
+ __u8 duplex;
+ __u8 port;
+ __u8 phy_address;
+ __u8 autoneg;
+ __u8 mdio_support;
+ __u8 eth_tp_mdix;
+ __u8 eth_tp_mdix_ctrl;
+ __s8 link_mode_masks_nwords;
+ __u32 reserved[8];
+ __u32 link_mode_masks[0];
+ /* layout of link_mode_masks fields:
+ * __u32 map_supported[link_mode_masks_nwords];
+ * __u32 map_advertising[link_mode_masks_nwords];
+ * __u32 map_lp_advertising[link_mode_masks_nwords];
+ */
+};
+#endif /* _UAPI_LINUX_ETHTOOL_H */
projects / thirdparty / lldpd.git / commitdiff
