ARM: at91: pm: change BU Power Switch to automatic mode

Change how the Backup Unit Power is configured and force the
automatic/hardware mode.
This change eliminates the need for software management of the power
switch, ensuring it transitions to the backup power source before
entering low power modes.

This is done in the only location where this switch was configured. It's
usually done in the bootloader.

Previously, the loss of the VDDANA (or VDDIN33) power source was not
automatically compensated by an alternative power source. This resulted
in the loss of Backup Unit content, including Backup Self-refresh low
power mode information, OTP emulation configuration, and boot
configuration, for instance.

Fixes: ac809e7879b1 ("ARM: at91: pm: switch backup area to vbat in backup mode")
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20241125165648.509162-1-nicolas.ferre@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>

diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index b9b995f8a36e149026de5896069e0bd34e432b5a..05a1547642b60fc23960ff5cc0e86417f92194a5 100644 (file)
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -598,7 +598,21 @@ static int at91_suspend_finish(unsigned long val)
        return 0;
 }
 
-static void at91_pm_switch_ba_to_vbat(void)
+/**
+ * at91_pm_switch_ba_to_auto() - Configure Backup Unit Power Switch
+ * to automatic/hardware mode.
+ *
+ * The Backup Unit Power Switch can be managed either by software or hardware.
+ * Enabling hardware mode allows the automatic transition of power between
+ * VDDANA (or VDDIN33) and VDDBU (or VBAT, respectively), based on the
+ * availability of these power sources.
+ *
+ * If the Backup Unit Power Switch is already in automatic mode, no action is
+ * required. If it is in software-controlled mode, it is switched to automatic
+ * mode to enhance safety and eliminate the need for toggling between power
+ * sources.
+ */
+static void at91_pm_switch_ba_to_auto(void)
 {
        unsigned int offset = offsetof(struct at91_pm_sfrbu_regs, pswbu);
        unsigned int val;
@@ -609,24 +623,19 @@ static void at91_pm_switch_ba_to_vbat(void)
 
        val = readl(soc_pm.data.sfrbu + offset);
 
-       /* Already on VBAT. */
-       if (!(val & soc_pm.sfrbu_regs.pswbu.state))
+       /* Already on auto/hardware. */
+       if (!(val & soc_pm.sfrbu_regs.pswbu.ctrl))
                return;
 
-       val &= ~soc_pm.sfrbu_regs.pswbu.softsw;
-       val |= soc_pm.sfrbu_regs.pswbu.key | soc_pm.sfrbu_regs.pswbu.ctrl;
+       val &= ~soc_pm.sfrbu_regs.pswbu.ctrl;
+       val |= soc_pm.sfrbu_regs.pswbu.key;
        writel(val, soc_pm.data.sfrbu + offset);
-
-       /* Wait for update. */
-       val = readl(soc_pm.data.sfrbu + offset);
-       while (val & soc_pm.sfrbu_regs.pswbu.state)
-               val = readl(soc_pm.data.sfrbu + offset);
 }
 
 static void at91_pm_suspend(suspend_state_t state)
 {
        if (soc_pm.data.mode == AT91_PM_BACKUP) {
-               at91_pm_switch_ba_to_vbat();
+               at91_pm_switch_ba_to_auto();
 
                cpu_suspend(0, at91_suspend_finish);