--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2025 AsiaRF Co., Ltd
+ * Author: Elwin Huang <elwin@asiarf.com>
+ */
+
+/dts-v1/;
+#include "mt7622.dtsi"
+#include "mt6380.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "AsiaRF AP7622 WH1";
+ compatible = "asiarf,ap7622-wh1", "mediatek,mt7622";
+
+ aliases {
+ serial0 = &uart0;
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 swiotlb=512";
+ };
+
+ cpus {
+ cpu@0 {
+ proc-supply = <&mt6380_vcpu_reg>;
+ sram-supply = <&mt6380_vm_reg>;
+ };
+
+ cpu@1 {
+ proc-supply = <&mt6380_vcpu_reg>;
+ sram-supply = <&mt6380_vm_reg>;
+ };
+ };
+
+ mmc1_pwrseq: mmc1_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 97 GPIO_ACTIVE_LOW>;
+ post-power-on-delay-ms = <200>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 102 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ memory@40000000 {
+ reg = <0 0x40000000 0 0x20000000>;// 512MiB
+ device_type = "memory";
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ status = "okay";
+
+ led_power: power {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_POWER;
+ gpios = <&pio 101 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WLAN;
+ gpios = <&pio 85 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+};
+
+&bch {
+ status = "okay";
+};
+
+&rtc {
+ status = "disabled";
+};
+
+ð {
+ pinctrl-names = "default";
+ pinctrl-0 = <ð_pins>;
+ status = "okay";
+
+ gmac0: mac@0 {
+ compatible = "mediatek,eth-mac";
+ nvmem-cells = <&macaddr_factory_7fff4>;
+ nvmem-cell-names = "mac-address";
+ reg = <0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch@1f {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-parent = <&pio>;
+ interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
+ reset-gpios = <&pio 54 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ nvmem-cells = <&macaddr_factory_7fffa>;
+ nvmem-cell-names = "mac-address";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+ };
+
+ };
+};
+
+&mmc1 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&sd0_pins_default>;
+ pinctrl-1 = <&sd0_pins_uhs>;
+ status = "okay";
+ bus-width = <4>;
+ max-frequency = <50000000>;
+ cap-sd-highspeed;
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_3p3v>;
+ assigned-clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
+
+ cap-mmc-highspeed;
+ cap-sdio-irq;
+ non-removable;
+ disable-wp;
+ drv-type = <2>;
+ mmc-pwrseq = <&mmc1_pwrseq>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mm6108_sdio@0 {
+ compatible = "morse,mm610x";
+ reset-gpios = <&pio 97 GPIO_ACTIVE_HIGH>;
+ power-gpios = <&pio 98 GPIO_ACTIVE_HIGH>,
+ <&pio 99 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ reg = <2>;
+ bus-width = <4>;
+ };
+};
+
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_pins>;
+ status = "okay";
+};
+
+&pcie1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie1_pins>;
+ status = "okay";
+};
+
+&pio {
+ eth_pins: eth-pins {
+ mux {
+ function = "eth";
+ groups = "mdc_mdio", "rgmii_via_gmac2";
+ };
+ };
+
+ pcie0_pins: pcie0-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie0_pad_perst",
+ "pcie0_1_waken",
+ "pcie0_1_clkreq";
+ };
+ };
+
+ pcie1_pins: pcie1-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie1_pad_perst",
+ "pcie1_0_waken",
+ "pcie1_0_clkreq";
+ };
+ };
+
+ pmic_bus_pins: pmic-bus-pins {
+ mux {
+ function = "pmic";
+ groups = "pmic_bus";
+ };
+ };
+
+ wled_pins: wled-pins {
+ mux {
+ function = "led";
+ groups = "wled";
+ };
+ };
+
+ sd0_pins_default: sd0-pins-default {
+ mux {
+ function = "sd";
+ groups = "sd_0";
+ };
+
+ /* "I2S2_OUT, "I2S4_IN"", "I2S3_IN", "I2S2_IN",
+ * "I2S4_OUT", "I2S3_OUT" are used as DAT0, DAT1,
+ * DAT2, DAT3, CMD, CLK for SD respectively.
+ */
+ conf-cmd-data {
+ pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
+ "I2S2_IN","I2S4_OUT";
+ input-enable;
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ conf-clk {
+ pins = "I2S3_OUT";
+ drive-strength = <12>;
+ bias-pull-down;
+ };
+ conf-cd {
+ pins = "TXD3";
+ bias-pull-up;
+ };
+ };
+
+ sd0_pins_uhs: sd0-pins-uhs {
+ mux {
+ function = "sd";
+ groups = "sd_0";
+ };
+
+ conf-cmd-data {
+ pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
+ "I2S2_IN","I2S4_OUT";
+ input-enable;
+ bias-pull-up;
+ };
+
+ conf-clk {
+ pins = "I2S3_OUT";
+ bias-pull-down;
+ };
+ };
+
+ /* Serial NAND is shared pin with SPI-NOR */
+ serial_nand_pins: serial-nand-pins {
+ mux {
+ function = "flash";
+ groups = "snfi";
+ };
+ };
+
+ spic0_pins: spic0-pins {
+ mux {
+ function = "spi";
+ groups = "spic0_0";
+ };
+ };
+
+ spic1_pins: spic1-pins {
+ mux {
+ function = "spi";
+ groups = "spic1_0";
+ };
+ };
+
+ uart0_pins: uart0-pins {
+ mux {
+ function = "uart";
+ groups = "uart0_0_tx_rx";
+ };
+ };
+
+ uart2_pins: uart2-pins {
+ mux {
+ function = "uart";
+ groups = "uart2_1_tx_rx";
+ };
+ };
+
+ watchdog_pins: watchdog-pins {
+ mux {
+ function = "watchdog";
+ groups = "watchdog";
+ };
+ };
+};
+
+&pwrap {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_bus_pins>;
+ status = "okay";
+};
+
+&snfi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&serial_nand_pins>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "spi-nand";
+ mediatek,bmt-table-size = <0x1000>;
+ mediatek,bmt-v2;
+ nand-ecc-engine = <&snfi>;
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "Preloader";
+ reg = <0x00000 0x0080000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "ATF";
+ reg = <0x80000 0x0040000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "Bootloader";
+ reg = <0xc0000 0x0080000>;
+ read-only;
+ };
+
+ partition@140000 {
+ label = "Config";
+ reg = <0x140000 0x0080000>;
+ };
+
+ partition@1c0000 {
+ label = "Factory";
+ reg = <0x1c0000 0x0100000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ factory_eeprom: eeprom@0 {
+ reg = <0x0 0x5000>;
+ };
+
+ macaddr_factory_7fff4: macaddr@7fff4 {
+ reg = <0x7fff4 0x6>;
+ };
+
+ macaddr_factory_7fffa: macaddr@7fffa {
+ reg = <0x7fffa 0x6>;
+ };
+ };
+ };
+
+ partition@2c0000 {
+ label = "firmware";
+ reg = <0x2c0000 0x2000000>;// 32 MiB
+
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "kernel";
+ reg = <0x0 0x0800000>;
+ };
+
+ partition@600000 {
+ label = "ubi";
+ reg = <0x800000 0x1800000>;
+ };
+ };
+
+ partition@22c0000 {
+ label = "User_data";
+ reg = <0x22c0000 0x5300000>;
+ };
+ };
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spic0_pins>;
+ status = "okay";
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spic1_pins>;
+ status = "okay";
+};
+
+&ssusb {
+ vusb33-supply = <®_3p3v>;
+ vbus-supply = <®_5v>;
+ status = "okay";
+};
+
+&u3phy {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&watchdog {
+ pinctrl-names = "default";
+ pinctrl-0 = <&watchdog_pins>;
+ status = "okay";
+};
+
+&wmac {
+ nvmem-cells = <&factory_eeprom>;
+ nvmem-cell-names = "eeprom";
+ status = "okay";
+};
projects / thirdparty / openwrt.git / commitdiff
