--- /dev/null
+From 6ad4a014c60dda6a1cb569be8230d12a255a8456 Mon Sep 17 00:00:00 2001
+From: Sasha Levin <sashal@kernel.org>
+Date: Mon, 18 Oct 2021 20:03:32 -0700
+Subject: hwmon: (lm90) Add basic support for TI TMP461
+
+From: Guenter Roeck <linux@roeck-us.net>
+
+[ Upstream commit f8344f7693a25d9025a59d164450b50c6f5aa3c0 ]
+
+TMP461 is almost identical to TMP451 and was actually detected as TMP451
+with the existing lm90 driver if its I2C address is 0x4c. Add support
+for it to the lm90 driver. At the same time, improve the chip detection
+function to at least try to distinguish between TMP451 and TMP461.
+
+As a side effect, this fixes commit 24333ac26d01 ("hwmon: (tmp401) use
+smb word operations instead of 2 smb byte operations"). TMP461 does not
+support word operations on temperature registers, which causes bad
+temperature readings with the tmp401 driver. The lm90 driver does not
+perform word operations on temperature registers and thus does not have
+this problem.
+
+Support is listed as basic because TMP461 supports a sensor resolution
+of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
+degrees C. Also, the TMP461 supports negative temperatures with its
+default temperature range, which is not the case for similar chips
+supported by the lm90 and the tmp401 drivers. Those limitations will be
+addressed with follow-up patches.
+
+Fixes: 24333ac26d01 ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
+Reported-by: David T. Wilson <david.wilson@nasa.gov>
+Cc: David T. Wilson <david.wilson@nasa.gov>
+Signed-off-by: Guenter Roeck <linux@roeck-us.net>
+Signed-off-by: Sasha Levin <sashal@kernel.org>
+---
+ Documentation/hwmon/lm90.rst | 10 +++++++
+ drivers/hwmon/Kconfig | 2 +-
+ drivers/hwmon/lm90.c | 54 ++++++++++++++++++++++++++----------
+ 3 files changed, 50 insertions(+), 16 deletions(-)
+
+diff --git a/Documentation/hwmon/lm90.rst b/Documentation/hwmon/lm90.rst
+index 78dfc01b47a23..03851cbe637ce 100644
+--- a/Documentation/hwmon/lm90.rst
++++ b/Documentation/hwmon/lm90.rst
+@@ -265,6 +265,16 @@ Supported chips:
+
+ http://www.ti.com/litv/pdf/sbos686
+
++ * Texas Instruments TMP461
++
++ Prefix: 'tmp461'
++
++ Addresses scanned: I2C 0x48 through 0x4F
++
++ Datasheet: Publicly available at TI website
++
++ https://www.ti.com/lit/gpn/tmp461
++
+ Author: Jean Delvare <jdelvare@suse.de>
+
+
+diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
+index fdf8fab7eb396..049563d503b68 100644
+--- a/drivers/hwmon/Kconfig
++++ b/drivers/hwmon/Kconfig
+@@ -1135,7 +1135,7 @@ config SENSORS_LM90
+ Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6654, MAX6657, MAX6658,
+ MAX6659, MAX6680, MAX6681, MAX6692, MAX6695, MAX6696,
+ ON Semiconductor NCT1008, Winbond/Nuvoton W83L771W/G/AWG/ASG,
+- Philips SA56004, GMT G781, and Texas Instruments TMP451
++ Philips SA56004, GMT G781, Texas Instruments TMP451 and TMP461
+ sensor chips.
+
+ This driver can also be built as a module. If so, the module
+diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c
+index 9d48a7405932f..e085e2a4fa16c 100644
+--- a/drivers/hwmon/lm90.c
++++ b/drivers/hwmon/lm90.c
+@@ -69,10 +69,10 @@
+ * This driver also supports the G781 from GMT. This device is compatible
+ * with the ADM1032.
+ *
+- * This driver also supports TMP451 from Texas Instruments. This device is
+- * supported in both compatibility and extended mode. It's mostly compatible
+- * with ADT7461 except for local temperature low byte register and max
+- * conversion rate.
++ * This driver also supports TMP451 and TMP461 from Texas Instruments.
++ * Those devices are supported in both compatibility and extended mode.
++ * They are mostly compatible with ADT7461 except for local temperature
++ * low byte register and max conversion rate.
+ *
+ * Since the LM90 was the first chipset supported by this driver, most
+ * comments will refer to this chipset, but are actually general and
+@@ -112,7 +112,7 @@ static const unsigned short normal_i2c[] = {
+ 0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
+
+ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
+- max6646, w83l771, max6696, sa56004, g781, tmp451, max6654 };
++ max6646, w83l771, max6696, sa56004, g781, tmp451, tmp461, max6654 };
+
+ /*
+ * The LM90 registers
+@@ -168,8 +168,12 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
+
+ #define LM90_MAX_CONVRATE_MS 16000 /* Maximum conversion rate in ms */
+
+-/* TMP451 registers */
++/* TMP451/TMP461 registers */
+ #define TMP451_REG_R_LOCAL_TEMPL 0x15
++#define TMP451_REG_CONALERT 0x22
++
++#define TMP461_REG_CHEN 0x16
++#define TMP461_REG_DFC 0x24
+
+ /*
+ * Device flags
+@@ -229,6 +233,7 @@ static const struct i2c_device_id lm90_id[] = {
+ { "w83l771", w83l771 },
+ { "sa56004", sa56004 },
+ { "tmp451", tmp451 },
++ { "tmp461", tmp461 },
+ { }
+ };
+ MODULE_DEVICE_TABLE(i2c, lm90_id);
+@@ -326,6 +331,10 @@ static const struct of_device_id __maybe_unused lm90_of_match[] = {
+ .compatible = "ti,tmp451",
+ .data = (void *)tmp451
+ },
++ {
++ .compatible = "ti,tmp461",
++ .data = (void *)tmp461
++ },
+ { },
+ };
+ MODULE_DEVICE_TABLE(of, lm90_of_match);
+@@ -427,6 +436,13 @@ static const struct lm90_params lm90_params[] = {
+ .max_convrate = 9,
+ .reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
+ },
++ [tmp461] = {
++ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
++ | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP,
++ .alert_alarms = 0x7c,
++ .max_convrate = 9,
++ .reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
++ },
+ };
+
+ /*
+@@ -1616,18 +1632,26 @@ static int lm90_detect(struct i2c_client *client,
+ && convrate <= 0x08)
+ name = "g781";
+ } else
+- if (address == 0x4C
+- && man_id == 0x55) { /* Texas Instruments */
+- int local_ext;
++ if (man_id == 0x55 && chip_id == 0x00 &&
++ (config1 & 0x1B) == 0x00 && convrate <= 0x09) {
++ int local_ext, conalert, chen, dfc;
+
+ local_ext = i2c_smbus_read_byte_data(client,
+ TMP451_REG_R_LOCAL_TEMPL);
+-
+- if (chip_id == 0x00 /* TMP451 */
+- && (config1 & 0x1B) == 0x00
+- && convrate <= 0x09
+- && (local_ext & 0x0F) == 0x00)
+- name = "tmp451";
++ conalert = i2c_smbus_read_byte_data(client,
++ TMP451_REG_CONALERT);
++ chen = i2c_smbus_read_byte_data(client, TMP461_REG_CHEN);
++ dfc = i2c_smbus_read_byte_data(client, TMP461_REG_DFC);
++
++ if ((local_ext & 0x0F) == 0x00 &&
++ (conalert & 0xf1) == 0x01 &&
++ (chen & 0xfc) == 0x00 &&
++ (dfc & 0xfc) == 0x00) {
++ if (address == 0x4c && !(chen & 0x03))
++ name = "tmp451";
++ else if (address >= 0x48 && address <= 0x4f)
++ name = "tmp461";
++ }
+ }
+
+ if (!name) { /* identification failed */
+--
+2.34.1
+
--- /dev/null
+From 6a5758315031498c829867d6e074ad6c86b4e937 Mon Sep 17 00:00:00 2001
+From: Sasha Levin <sashal@kernel.org>
+Date: Wed, 13 May 2020 11:42:48 -0700
+Subject: hwmon: (lm90) Add max6654 support to lm90 driver
+
+From: Josh Lehan <krellan@google.com>
+
+[ Upstream commit 229d495d8189ae785dacee72e5633a58edc25ddf ]
+
+Add support for the Maxim MAX6654 to the lm90 driver.
+
+The MAX6654 is a temperature sensor, similar to the others,
+but with some differences regarding the configuration
+register, and the sampling rate at which extended resolution
+becomes possible.
+
+Signed-off-by: Josh Lehan <krellan@google.com>
+Link: https://lore.kernel.org/r/20200513184248.145765-1-krellan@google.com
+Signed-off-by: Guenter Roeck <linux@roeck-us.net>
+Signed-off-by: Sasha Levin <sashal@kernel.org>
+---
+ Documentation/hwmon/lm90.rst | 23 ++++++++++++++++--
+ drivers/hwmon/Kconfig | 9 ++++----
+ drivers/hwmon/lm90.c | 45 ++++++++++++++++++++++++++++++++----
+ 3 files changed, 67 insertions(+), 10 deletions(-)
+
+diff --git a/Documentation/hwmon/lm90.rst b/Documentation/hwmon/lm90.rst
+index 953315987c06e..78dfc01b47a23 100644
+--- a/Documentation/hwmon/lm90.rst
++++ b/Documentation/hwmon/lm90.rst
+@@ -123,6 +123,18 @@ Supported chips:
+
+ http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3497
+
++ * Maxim MAX6654
++
++ Prefix: 'max6654'
++
++ Addresses scanned: I2C 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
++
++ 0x4c, 0x4d and 0x4e
++
++ Datasheet: Publicly available at the Maxim website
++
++ https://www.maximintegrated.com/en/products/sensors/MAX6654.html
++
+ * Maxim MAX6657
+
+ Prefix: 'max6657'
+@@ -301,6 +313,13 @@ ADT7461, ADT7461A, NCT1008:
+ * Extended temperature range (breaks compatibility)
+ * Lower resolution for remote temperature
+
++MAX6654:
++ * Better local resolution
++ * Selectable address
++ * Remote sensor type selection
++ * Extended temperature range
++ * Extended resolution only available when conversion rate <= 1 Hz
++
+ MAX6657 and MAX6658:
+ * Better local resolution
+ * Remote sensor type selection
+@@ -336,8 +355,8 @@ SA56004X:
+
+ All temperature values are given in degrees Celsius. Resolution
+ is 1.0 degree for the local temperature, 0.125 degree for the remote
+-temperature, except for the MAX6657, MAX6658 and MAX6659 which have a
+-resolution of 0.125 degree for both temperatures.
++temperature, except for the MAX6654, MAX6657, MAX6658 and MAX6659 which have
++a resolution of 0.125 degree for both temperatures.
+
+ Each sensor has its own high and low limits, plus a critical limit.
+ Additionally, there is a relative hysteresis value common to both critical
+diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
+index 13a6b4afb4b36..fdf8fab7eb396 100644
+--- a/drivers/hwmon/Kconfig
++++ b/drivers/hwmon/Kconfig
+@@ -1132,10 +1132,11 @@ config SENSORS_LM90
+ help
+ If you say yes here you get support for National Semiconductor LM90,
+ LM86, LM89 and LM99, Analog Devices ADM1032, ADT7461, and ADT7461A,
+- Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6657, MAX6658, MAX6659,
+- MAX6680, MAX6681, MAX6692, MAX6695, MAX6696, ON Semiconductor NCT1008,
+- Winbond/Nuvoton W83L771W/G/AWG/ASG, Philips SA56004, GMT G781, and
+- Texas Instruments TMP451 sensor chips.
++ Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6654, MAX6657, MAX6658,
++ MAX6659, MAX6680, MAX6681, MAX6692, MAX6695, MAX6696,
++ ON Semiconductor NCT1008, Winbond/Nuvoton W83L771W/G/AWG/ASG,
++ Philips SA56004, GMT G781, and Texas Instruments TMP451
++ sensor chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called lm90.
+diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c
+index 6d6f543baea68..9d48a7405932f 100644
+--- a/drivers/hwmon/lm90.c
++++ b/drivers/hwmon/lm90.c
+@@ -35,6 +35,14 @@
+ * explicitly as max6659, or if its address is not 0x4c.
+ * These chips lack the remote temperature offset feature.
+ *
++ * This driver also supports the MAX6654 chip made by Maxim. This chip can
++ * be at 9 different addresses, similar to MAX6680/MAX6681. The MAX6654 is
++ * otherwise similar to MAX6657/MAX6658/MAX6659. Extended range is available
++ * by setting the configuration register accordingly, and is done during
++ * initialization. Extended precision is only available at conversion rates
++ * of 1 Hz and slower. Note that extended precision is not enabled by
++ * default, as this driver initializes all chips to 2 Hz by design.
++ *
+ * This driver also supports the MAX6646, MAX6647, MAX6648, MAX6649 and
+ * MAX6692 chips made by Maxim. These are again similar to the LM86,
+ * but they use unsigned temperature values and can report temperatures
+@@ -94,8 +102,8 @@
+ * have address 0x4d.
+ * MAX6647 has address 0x4e.
+ * MAX6659 can have address 0x4c, 0x4d or 0x4e.
+- * MAX6680 and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
+- * 0x4c, 0x4d or 0x4e.
++ * MAX6654, MAX6680, and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29,
++ * 0x2a, 0x2b, 0x4c, 0x4d or 0x4e.
+ * SA56004 can have address 0x48 through 0x4F.
+ */
+
+@@ -104,7 +112,7 @@ static const unsigned short normal_i2c[] = {
+ 0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
+
+ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
+- max6646, w83l771, max6696, sa56004, g781, tmp451 };
++ max6646, w83l771, max6696, sa56004, g781, tmp451, max6654 };
+
+ /*
+ * The LM90 registers
+@@ -145,7 +153,7 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
+ #define LM90_REG_R_TCRIT_HYST 0x21
+ #define LM90_REG_W_TCRIT_HYST 0x21
+
+-/* MAX6646/6647/6649/6657/6658/6659/6695/6696 registers */
++/* MAX6646/6647/6649/6654/6657/6658/6659/6695/6696 registers */
+
+ #define MAX6657_REG_R_LOCAL_TEMPL 0x11
+ #define MAX6696_REG_R_STATUS2 0x12
+@@ -209,6 +217,7 @@ static const struct i2c_device_id lm90_id[] = {
+ { "max6646", max6646 },
+ { "max6647", max6646 },
+ { "max6649", max6646 },
++ { "max6654", max6654 },
+ { "max6657", max6657 },
+ { "max6658", max6657 },
+ { "max6659", max6659 },
+@@ -269,6 +278,10 @@ static const struct of_device_id __maybe_unused lm90_of_match[] = {
+ .compatible = "dallas,max6649",
+ .data = (void *)max6646
+ },
++ {
++ .compatible = "dallas,max6654",
++ .data = (void *)max6654
++ },
+ {
+ .compatible = "dallas,max6657",
+ .data = (void *)max6657
+@@ -367,6 +380,11 @@ static const struct lm90_params lm90_params[] = {
+ .max_convrate = 6,
+ .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
+ },
++ [max6654] = {
++ .alert_alarms = 0x7c,
++ .max_convrate = 7,
++ .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
++ },
+ [max6657] = {
+ .flags = LM90_PAUSE_FOR_CONFIG,
+ .alert_alarms = 0x7c,
+@@ -1556,6 +1574,16 @@ static int lm90_detect(struct i2c_client *client,
+ && (config1 & 0x3f) == 0x00
+ && convrate <= 0x07) {
+ name = "max6646";
++ } else
++ /*
++ * The chip_id of the MAX6654 holds the revision of the chip.
++ * The lowest 3 bits of the config1 register are unused and
++ * should return zero when read.
++ */
++ if (chip_id == 0x08
++ && (config1 & 0x07) == 0x00
++ && convrate <= 0x07) {
++ name = "max6654";
+ }
+ } else
+ if (address == 0x4C
+@@ -1659,6 +1687,15 @@ static int lm90_init_client(struct i2c_client *client, struct lm90_data *data)
+ if (data->kind == max6680)
+ config |= 0x18;
+
++ /*
++ * Put MAX6654 into extended range (0x20, extend minimum range from
++ * 0 degrees to -64 degrees). Note that extended resolution is not
++ * possible on the MAX6654 unless conversion rate is set to 1 Hz or
++ * slower, which is intentionally not done by default.
++ */
++ if (data->kind == max6654)
++ config |= 0x20;
++
+ /*
+ * Select external channel 0 for max6695/96
+ */
+--
+2.34.1
+
--- /dev/null
+From 2738a110e20ba603e6ffe5b3345ef3e654094d51 Mon Sep 17 00:00:00 2001
+From: Sasha Levin <sashal@kernel.org>
+Date: Sat, 13 Nov 2021 08:55:06 -0800
+Subject: hwmon: (lm90) Drop critical attribute support for MAX6654
+
+From: Guenter Roeck <linux@roeck-us.net>
+
+[ Upstream commit 16ba51b5dcd3f6dde2e51d5ccc86313119dcf889 ]
+
+Tests with a real chip and a closer look into the datasheet show that
+MAX6654 does not support CRIT/THERM/OVERTEMP limits, so drop support
+of the respective attributes for this chip.
+
+Introduce LM90_HAVE_CRIT flag and use it to instantiate critical limit
+attributes to solve the problem.
+
+Cc: Josh Lehan <krellan@google.com>
+Fixes: 229d495d8189 ("hwmon: (lm90) Add max6654 support to lm90 driver")
+Signed-off-by: Guenter Roeck <linux@roeck-us.net>
+Signed-off-by: Sasha Levin <sashal@kernel.org>
+---
+ drivers/hwmon/lm90.c | 86 +++++++++++++++++++++++++-------------------
+ 1 file changed, 49 insertions(+), 37 deletions(-)
+
+diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c
+index c4d8012806fe2..3ce83f2f5d82f 100644
+--- a/drivers/hwmon/lm90.c
++++ b/drivers/hwmon/lm90.c
+@@ -35,13 +35,14 @@
+ * explicitly as max6659, or if its address is not 0x4c.
+ * These chips lack the remote temperature offset feature.
+ *
+- * This driver also supports the MAX6654 chip made by Maxim. This chip can
+- * be at 9 different addresses, similar to MAX6680/MAX6681. The MAX6654 is
+- * otherwise similar to MAX6657/MAX6658/MAX6659. Extended range is available
+- * by setting the configuration register accordingly, and is done during
+- * initialization. Extended precision is only available at conversion rates
+- * of 1 Hz and slower. Note that extended precision is not enabled by
+- * default, as this driver initializes all chips to 2 Hz by design.
++ * This driver also supports the MAX6654 chip made by Maxim. This chip can be
++ * at 9 different addresses, similar to MAX6680/MAX6681. The MAX6654 is similar
++ * to MAX6657/MAX6658/MAX6659, but does not support critical temperature
++ * limits. Extended range is available by setting the configuration register
++ * accordingly, and is done during initialization. Extended precision is only
++ * available at conversion rates of 1 Hz and slower. Note that extended
++ * precision is not enabled by default, as this driver initializes all chips
++ * to 2 Hz by design.
+ *
+ * This driver also supports the MAX6646, MAX6647, MAX6648, MAX6649 and
+ * MAX6692 chips made by Maxim. These are again similar to the LM86,
+@@ -188,6 +189,7 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
+ #define LM90_HAVE_BROKEN_ALERT (1 << 7) /* Broken alert */
+ #define LM90_HAVE_EXTENDED_TEMP (1 << 8) /* extended temperature support*/
+ #define LM90_PAUSE_FOR_CONFIG (1 << 9) /* Pause conversion for config */
++#define LM90_HAVE_CRIT (1 << 10)/* Chip supports CRIT/OVERT register */
+
+ /* LM90 status */
+ #define LM90_STATUS_LTHRM (1 << 0) /* local THERM limit tripped */
+@@ -354,38 +356,43 @@ struct lm90_params {
+ static const struct lm90_params lm90_params[] = {
+ [adm1032] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+- | LM90_HAVE_BROKEN_ALERT,
++ | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 10,
+ },
+ [adt7461] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+- | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP,
++ | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP
++ | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 10,
+ },
+ [g781] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+- | LM90_HAVE_BROKEN_ALERT,
++ | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 8,
+ },
+ [lm86] = {
+- .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
++ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
++ | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7b,
+ .max_convrate = 9,
+ },
+ [lm90] = {
+- .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
++ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
++ | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7b,
+ .max_convrate = 9,
+ },
+ [lm99] = {
+- .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
++ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
++ | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7b,
+ .max_convrate = 9,
+ },
+ [max6646] = {
++ .flags = LM90_HAVE_CRIT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 6,
+ .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
+@@ -396,50 +403,50 @@ static const struct lm90_params lm90_params[] = {
+ .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
+ },
+ [max6657] = {
+- .flags = LM90_PAUSE_FOR_CONFIG,
++ .flags = LM90_PAUSE_FOR_CONFIG | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 8,
+ .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
+ },
+ [max6659] = {
+- .flags = LM90_HAVE_EMERGENCY,
++ .flags = LM90_HAVE_EMERGENCY | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 8,
+ .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
+ },
+ [max6680] = {
+- .flags = LM90_HAVE_OFFSET,
++ .flags = LM90_HAVE_OFFSET | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 7,
+ },
+ [max6696] = {
+ .flags = LM90_HAVE_EMERGENCY
+- | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3,
++ | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3 | LM90_HAVE_CRIT,
+ .alert_alarms = 0x1c7c,
+ .max_convrate = 6,
+ .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
+ },
+ [w83l771] = {
+- .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
++ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 8,
+ },
+ [sa56004] = {
+- .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
++ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7b,
+ .max_convrate = 9,
+ .reg_local_ext = SA56004_REG_R_LOCAL_TEMPL,
+ },
+ [tmp451] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+- | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP,
++ | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 9,
+ .reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
+ },
+ [tmp461] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+- | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP,
++ | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP | LM90_HAVE_CRIT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 9,
+ .reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
+@@ -667,20 +674,22 @@ static int lm90_update_limits(struct device *dev)
+ struct i2c_client *client = data->client;
+ int val;
+
+- val = lm90_read_reg(client, LM90_REG_R_LOCAL_CRIT);
+- if (val < 0)
+- return val;
+- data->temp8[LOCAL_CRIT] = val;
++ if (data->flags & LM90_HAVE_CRIT) {
++ val = lm90_read_reg(client, LM90_REG_R_LOCAL_CRIT);
++ if (val < 0)
++ return val;
++ data->temp8[LOCAL_CRIT] = val;
+
+- val = lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT);
+- if (val < 0)
+- return val;
+- data->temp8[REMOTE_CRIT] = val;
++ val = lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT);
++ if (val < 0)
++ return val;
++ data->temp8[REMOTE_CRIT] = val;
+
+- val = lm90_read_reg(client, LM90_REG_R_TCRIT_HYST);
+- if (val < 0)
+- return val;
+- data->temp_hyst = val;
++ val = lm90_read_reg(client, LM90_REG_R_TCRIT_HYST);
++ if (val < 0)
++ return val;
++ data->temp_hyst = val;
++ }
+
+ val = lm90_read_reg(client, LM90_REG_R_REMOTE_LOWH);
+ if (val < 0)
+@@ -1867,11 +1876,14 @@ static int lm90_probe(struct i2c_client *client,
+ info->config = data->channel_config;
+
+ data->channel_config[0] = HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX |
+- HWMON_T_CRIT | HWMON_T_CRIT_HYST | HWMON_T_MIN_ALARM |
+- HWMON_T_MAX_ALARM | HWMON_T_CRIT_ALARM;
++ HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM;
+ data->channel_config[1] = HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX |
+- HWMON_T_CRIT | HWMON_T_CRIT_HYST | HWMON_T_MIN_ALARM |
+- HWMON_T_MAX_ALARM | HWMON_T_CRIT_ALARM | HWMON_T_FAULT;
++ HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM | HWMON_T_FAULT;
++
++ if (data->flags & LM90_HAVE_CRIT) {
++ data->channel_config[0] |= HWMON_T_CRIT | HWMON_T_CRIT_ALARM | HWMON_T_CRIT_HYST;
++ data->channel_config[1] |= HWMON_T_CRIT | HWMON_T_CRIT_ALARM | HWMON_T_CRIT_HYST;
++ }
+
+ if (data->flags & LM90_HAVE_OFFSET)
+ data->channel_config[1] |= HWMON_T_OFFSET;
+--
+2.34.1
+
--- /dev/null
+From 7ad7d50b88fbe4378e75ec268d0e6c7429ffc4b4 Mon Sep 17 00:00:00 2001
+From: Sasha Levin <sashal@kernel.org>
+Date: Sat, 6 Nov 2021 10:02:44 -0700
+Subject: hwmon: (lm90) Fix usage of CONFIG2 register in detect function
+
+From: Guenter Roeck <linux@roeck-us.net>
+
+[ Upstream commit fce15c45d3fbd9fc1feaaf3210d8e3f8b33dfd3a ]
+
+The detect function had a comment "Make compiler happy" when id did not
+read the second configuration register. As it turns out, the code was
+checking the contents of this register for manufacturer ID 0xA1 (NXP
+Semiconductor/Philips), but never actually read the register. So it
+wasn't surprising that the compiler complained, and it indeed had a point.
+Fix the code to read the register contents for manufacturer ID 0xa1.
+
+At the same time, the code was reading the register for manufacturer ID
+0x41 (Analog Devices), but it was not using the results. In effect it was
+just checking if reading the register returned an error. That doesn't
+really add much if any value, so stop doing that.
+
+Fixes: f90be42fb383 ("hwmon: (lm90) Refactor reading of config2 register")
+Signed-off-by: Guenter Roeck <linux@roeck-us.net>
+Signed-off-by: Sasha Levin <sashal@kernel.org>
+---
+ drivers/hwmon/lm90.c | 5 ++---
+ 1 file changed, 2 insertions(+), 3 deletions(-)
+
+diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c
+index 9b3c9f390ef81..6d6f543baea68 100644
+--- a/drivers/hwmon/lm90.c
++++ b/drivers/hwmon/lm90.c
+@@ -1420,12 +1420,11 @@ static int lm90_detect(struct i2c_client *client,
+ if (man_id < 0 || chip_id < 0 || config1 < 0 || convrate < 0)
+ return -ENODEV;
+
+- if (man_id == 0x01 || man_id == 0x5C || man_id == 0x41) {
++ if (man_id == 0x01 || man_id == 0x5C || man_id == 0xA1) {
+ config2 = i2c_smbus_read_byte_data(client, LM90_REG_R_CONFIG2);
+ if (config2 < 0)
+ return -ENODEV;
+- } else
+- config2 = 0; /* Make compiler happy */
++ }
+
+ if ((address == 0x4C || address == 0x4D)
+ && man_id == 0x01) { /* National Semiconductor */
+--
+2.34.1
+
--- /dev/null
+From dca5864b5158de65e18210a36571c618be633d28 Mon Sep 17 00:00:00 2001
+From: Sasha Levin <sashal@kernel.org>
+Date: Thu, 21 Oct 2021 01:49:50 -0700
+Subject: hwmon: (lm90) Introduce flag indicating extended temperature support
+
+From: Guenter Roeck <linux@roeck-us.net>
+
+[ Upstream commit f347e249fcf920ad6974cbd898e2ec0b366a1c34 ]
+
+A flag indicating extended temperature support makes it easier
+to add support for additional chips with this functionality.
+
+Cc: David T. Wilson <david.wilson@nasa.gov>
+Signed-off-by: Guenter Roeck <linux@roeck-us.net>
+Signed-off-by: Sasha Levin <sashal@kernel.org>
+---
+ drivers/hwmon/lm90.c | 21 +++++++++++----------
+ 1 file changed, 11 insertions(+), 10 deletions(-)
+
+diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c
+index e085e2a4fa16c..c4d8012806fe2 100644
+--- a/drivers/hwmon/lm90.c
++++ b/drivers/hwmon/lm90.c
+@@ -186,7 +186,8 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
+ #define LM90_HAVE_EMERGENCY_ALARM (1 << 5)/* emergency alarm */
+ #define LM90_HAVE_TEMP3 (1 << 6) /* 3rd temperature sensor */
+ #define LM90_HAVE_BROKEN_ALERT (1 << 7) /* Broken alert */
+-#define LM90_PAUSE_FOR_CONFIG (1 << 8) /* Pause conversion for config */
++#define LM90_HAVE_EXTENDED_TEMP (1 << 8) /* extended temperature support*/
++#define LM90_PAUSE_FOR_CONFIG (1 << 9) /* Pause conversion for config */
+
+ /* LM90 status */
+ #define LM90_STATUS_LTHRM (1 << 0) /* local THERM limit tripped */
+@@ -359,7 +360,7 @@ static const struct lm90_params lm90_params[] = {
+ },
+ [adt7461] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+- | LM90_HAVE_BROKEN_ALERT,
++ | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP,
+ .alert_alarms = 0x7c,
+ .max_convrate = 10,
+ },
+@@ -431,7 +432,7 @@ static const struct lm90_params lm90_params[] = {
+ },
+ [tmp451] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+- | LM90_HAVE_BROKEN_ALERT,
++ | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP,
+ .alert_alarms = 0x7c,
+ .max_convrate = 9,
+ .reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
+@@ -1013,7 +1014,7 @@ static int lm90_get_temp11(struct lm90_data *data, int index)
+ s16 temp11 = data->temp11[index];
+ int temp;
+
+- if (data->kind == adt7461 || data->kind == tmp451)
++ if (data->flags & LM90_HAVE_EXTENDED_TEMP)
+ temp = temp_from_u16_adt7461(data, temp11);
+ else if (data->kind == max6646)
+ temp = temp_from_u16(temp11);
+@@ -1047,7 +1048,7 @@ static int lm90_set_temp11(struct lm90_data *data, int index, long val)
+ if (data->kind == lm99 && index <= 2)
+ val -= 16000;
+
+- if (data->kind == adt7461 || data->kind == tmp451)
++ if (data->flags & LM90_HAVE_EXTENDED_TEMP)
+ data->temp11[index] = temp_to_u16_adt7461(data, val);
+ else if (data->kind == max6646)
+ data->temp11[index] = temp_to_u8(val) << 8;
+@@ -1074,7 +1075,7 @@ static int lm90_get_temp8(struct lm90_data *data, int index)
+ s8 temp8 = data->temp8[index];
+ int temp;
+
+- if (data->kind == adt7461 || data->kind == tmp451)
++ if (data->flags & LM90_HAVE_EXTENDED_TEMP)
+ temp = temp_from_u8_adt7461(data, temp8);
+ else if (data->kind == max6646)
+ temp = temp_from_u8(temp8);
+@@ -1107,7 +1108,7 @@ static int lm90_set_temp8(struct lm90_data *data, int index, long val)
+ if (data->kind == lm99 && index == 3)
+ val -= 16000;
+
+- if (data->kind == adt7461 || data->kind == tmp451)
++ if (data->flags & LM90_HAVE_EXTENDED_TEMP)
+ data->temp8[index] = temp_to_u8_adt7461(data, val);
+ else if (data->kind == max6646)
+ data->temp8[index] = temp_to_u8(val);
+@@ -1125,7 +1126,7 @@ static int lm90_get_temphyst(struct lm90_data *data, int index)
+ {
+ int temp;
+
+- if (data->kind == adt7461 || data->kind == tmp451)
++ if (data->flags & LM90_HAVE_EXTENDED_TEMP)
+ temp = temp_from_u8_adt7461(data, data->temp8[index]);
+ else if (data->kind == max6646)
+ temp = temp_from_u8(data->temp8[index]);
+@@ -1145,7 +1146,7 @@ static int lm90_set_temphyst(struct lm90_data *data, long val)
+ int temp;
+ int err;
+
+- if (data->kind == adt7461 || data->kind == tmp451)
++ if (data->flags & LM90_HAVE_EXTENDED_TEMP)
+ temp = temp_from_u8_adt7461(data, data->temp8[LOCAL_CRIT]);
+ else if (data->kind == max6646)
+ temp = temp_from_u8(data->temp8[LOCAL_CRIT]);
+@@ -1698,7 +1699,7 @@ static int lm90_init_client(struct i2c_client *client, struct lm90_data *data)
+ lm90_set_convrate(client, data, 500); /* 500ms; 2Hz conversion rate */
+
+ /* Check Temperature Range Select */
+- if (data->kind == adt7461 || data->kind == tmp451) {
++ if (data->flags & LM90_HAVE_EXTENDED_TEMP) {
+ if (config & 0x04)
+ data->flags |= LM90_FLAG_ADT7461_EXT;
+ }
+--
+2.34.1
+
--- /dev/null
+From fd88d027fbebc9ec9e9ad3b9b048dfbac879d33f Mon Sep 17 00:00:00 2001
+From: Sasha Levin <sashal@kernel.org>
+Date: Mon, 29 Nov 2021 00:08:13 -0800
+Subject: Input: elantech - fix stack out of bound access in
+ elantech_change_report_id()
+
+From: Andrea Righi <andrea.righi@canonical.com>
+
+[ Upstream commit 1d72d9f960ccf1052a0630a68c3d358791dbdaaa ]
+
+The array param[] in elantech_change_report_id() must be at least 3
+bytes, because elantech_read_reg_params() is calling ps2_command() with
+PSMOUSE_CMD_GETINFO, that is going to access 3 bytes from param[], but
+it's defined in the stack as an array of 2 bytes, therefore we have a
+potential stack out-of-bounds access here, also confirmed by KASAN:
+
+[ 6.512374] BUG: KASAN: stack-out-of-bounds in __ps2_command+0x372/0x7e0
+[ 6.512397] Read of size 1 at addr ffff8881024d77c2 by task kworker/2:1/118
+
+[ 6.512416] CPU: 2 PID: 118 Comm: kworker/2:1 Not tainted 5.13.0-22-generic #22+arighi20211110
+[ 6.512428] Hardware name: LENOVO 20T8000QGE/20T8000QGE, BIOS R1AET32W (1.08 ) 08/14/2020
+[ 6.512436] Workqueue: events_long serio_handle_event
+[ 6.512453] Call Trace:
+[ 6.512462] show_stack+0x52/0x58
+[ 6.512474] dump_stack+0xa1/0xd3
+[ 6.512487] print_address_description.constprop.0+0x1d/0x140
+[ 6.512502] ? __ps2_command+0x372/0x7e0
+[ 6.512516] __kasan_report.cold+0x7d/0x112
+[ 6.512527] ? _raw_write_lock_irq+0x20/0xd0
+[ 6.512539] ? __ps2_command+0x372/0x7e0
+[ 6.512552] kasan_report+0x3c/0x50
+[ 6.512564] __asan_load1+0x6a/0x70
+[ 6.512575] __ps2_command+0x372/0x7e0
+[ 6.512589] ? ps2_drain+0x240/0x240
+[ 6.512601] ? dev_printk_emit+0xa2/0xd3
+[ 6.512612] ? dev_vprintk_emit+0xc5/0xc5
+[ 6.512621] ? __kasan_check_write+0x14/0x20
+[ 6.512634] ? mutex_lock+0x8f/0xe0
+[ 6.512643] ? __mutex_lock_slowpath+0x20/0x20
+[ 6.512655] ps2_command+0x52/0x90
+[ 6.512670] elantech_ps2_command+0x4f/0xc0 [psmouse]
+[ 6.512734] elantech_change_report_id+0x1e6/0x256 [psmouse]
+[ 6.512799] ? elantech_report_trackpoint.constprop.0.cold+0xd/0xd [psmouse]
+[ 6.512863] ? ps2_command+0x7f/0x90
+[ 6.512877] elantech_query_info.cold+0x6bd/0x9ed [psmouse]
+[ 6.512943] ? elantech_setup_ps2+0x460/0x460 [psmouse]
+[ 6.513005] ? psmouse_reset+0x69/0xb0 [psmouse]
+[ 6.513064] ? psmouse_attr_set_helper+0x2a0/0x2a0 [psmouse]
+[ 6.513122] ? phys_pmd_init+0x30e/0x521
+[ 6.513137] elantech_init+0x8a/0x200 [psmouse]
+[ 6.513200] ? elantech_init_ps2+0xf0/0xf0 [psmouse]
+[ 6.513249] ? elantech_query_info+0x440/0x440 [psmouse]
+[ 6.513296] ? synaptics_send_cmd+0x60/0x60 [psmouse]
+[ 6.513342] ? elantech_query_info+0x440/0x440 [psmouse]
+[ 6.513388] ? psmouse_try_protocol+0x11e/0x170 [psmouse]
+[ 6.513432] psmouse_extensions+0x65d/0x6e0 [psmouse]
+[ 6.513476] ? psmouse_try_protocol+0x170/0x170 [psmouse]
+[ 6.513519] ? mutex_unlock+0x22/0x40
+[ 6.513526] ? ps2_command+0x7f/0x90
+[ 6.513536] ? psmouse_probe+0xa3/0xf0 [psmouse]
+[ 6.513580] psmouse_switch_protocol+0x27d/0x2e0 [psmouse]
+[ 6.513624] psmouse_connect+0x272/0x530 [psmouse]
+[ 6.513669] serio_driver_probe+0x55/0x70
+[ 6.513679] really_probe+0x190/0x720
+[ 6.513689] driver_probe_device+0x160/0x1f0
+[ 6.513697] device_driver_attach+0x119/0x130
+[ 6.513705] ? device_driver_attach+0x130/0x130
+[ 6.513713] __driver_attach+0xe7/0x1a0
+[ 6.513720] ? device_driver_attach+0x130/0x130
+[ 6.513728] bus_for_each_dev+0xfb/0x150
+[ 6.513738] ? subsys_dev_iter_exit+0x10/0x10
+[ 6.513748] ? _raw_write_unlock_bh+0x30/0x30
+[ 6.513757] driver_attach+0x2d/0x40
+[ 6.513764] serio_handle_event+0x199/0x3d0
+[ 6.513775] process_one_work+0x471/0x740
+[ 6.513785] worker_thread+0x2d2/0x790
+[ 6.513794] ? process_one_work+0x740/0x740
+[ 6.513802] kthread+0x1b4/0x1e0
+[ 6.513809] ? set_kthread_struct+0x80/0x80
+[ 6.513816] ret_from_fork+0x22/0x30
+
+[ 6.513832] The buggy address belongs to the page:
+[ 6.513838] page:00000000bc35e189 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1024d7
+[ 6.513847] flags: 0x17ffffc0000000(node=0|zone=2|lastcpupid=0x1fffff)
+[ 6.513860] raw: 0017ffffc0000000 dead000000000100 dead000000000122 0000000000000000
+[ 6.513867] raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
+[ 6.513872] page dumped because: kasan: bad access detected
+
+[ 6.513879] addr ffff8881024d77c2 is located in stack of task kworker/2:1/118 at offset 34 in frame:
+[ 6.513887] elantech_change_report_id+0x0/0x256 [psmouse]
+
+[ 6.513941] this frame has 1 object:
+[ 6.513947] [32, 34) 'param'
+
+[ 6.513956] Memory state around the buggy address:
+[ 6.513962] ffff8881024d7680: f2 f2 f2 f2 f2 00 00 f3 f3 00 00 00 00 00 00 00
+[ 6.513969] ffff8881024d7700: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+[ 6.513976] >ffff8881024d7780: 00 00 00 00 f1 f1 f1 f1 02 f3 f3 f3 00 00 00 00
+[ 6.513982] ^
+[ 6.513988] ffff8881024d7800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+[ 6.513995] ffff8881024d7880: 00 f1 f1 f1 f1 03 f2 03 f2 03 f3 f3 f3 00 00 00
+[ 6.514000] ==================================================================
+
+Define param[] in elantech_change_report_id() as an array of 3 bytes to
+prevent the out-of-bounds access in the stack.
+
+Fixes: e4c9062717fe ("Input: elantech - fix protocol errors for some trackpoints in SMBus mode")
+BugLink: https://bugs.launchpad.net/bugs/1945590
+Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
+Reviewed-by: Wolfram Sang <wsa@kernel.org>
+Link: https://lore.kernel.org/r/20211116095559.24395-1-andrea.righi@canonical.com
+Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
+Signed-off-by: Sasha Levin <sashal@kernel.org>
+---
+ drivers/input/mouse/elantech.c | 8 +++++++-
+ 1 file changed, 7 insertions(+), 1 deletion(-)
+
+diff --git a/drivers/input/mouse/elantech.c b/drivers/input/mouse/elantech.c
+index 0b5ed963cb0e1..3e78c26025815 100644
+--- a/drivers/input/mouse/elantech.c
++++ b/drivers/input/mouse/elantech.c
+@@ -1588,7 +1588,13 @@ static const struct dmi_system_id no_hw_res_dmi_table[] = {
+ */
+ static int elantech_change_report_id(struct psmouse *psmouse)
+ {
+- unsigned char param[2] = { 0x10, 0x03 };
++ /*
++ * NOTE: the code is expecting to receive param[] as an array of 3
++ * items (see __ps2_command()), even if in this case only 2 are
++ * actually needed. Make sure the array size is 3 to avoid potential
++ * stack out-of-bound accesses.
++ */
++ unsigned char param[3] = { 0x10, 0x03 };
+
+ if (elantech_write_reg_params(psmouse, 0x7, param) ||
+ elantech_read_reg_params(psmouse, 0x7, param) ||
+--
+2.34.1
+
fjes-check-for-error-irq.patch
drivers-net-smc911x-check-for-error-irq.patch
sfc-falcon-check-null-pointer-of-rx_queue-page_ring.patch
+input-elantech-fix-stack-out-of-bound-access-in-elan.patch
+hwmon-lm90-fix-usage-of-config2-register-in-detect-f.patch
+hwmon-lm90-add-max6654-support-to-lm90-driver.patch
+hwmon-lm90-add-basic-support-for-ti-tmp461.patch
+hwmon-lm90-introduce-flag-indicating-extended-temper.patch
+hwmon-lm90-drop-critical-attribute-support-for-max66.patch
projects / thirdparty / kernel / stable-queue.git / commitdiff
