net: phy: micrel: fix typos in comments

Fix several spelling and grammatical errors in comments across
micrel PHY drivers. Corrections include:
- "dealy" -> "delay"
- "autonegotation" -> "autonegotiation"
- "recheas" -> "reaches"
- "one" -> "on"
- "improvenent" -> "improvement"
- "intput" -> "input"

Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251017193525.1457064-2-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 65994d97c403c83e18821c5dac73b5e3300052f3..5f2c7e5c314f536f3fa092cce26a37b46309b74e 100644 (file)
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -1050,7 +1050,7 @@ static int ksz9021_config_init(struct phy_device *phydev)
 #define TX_CLK_ID                      0x1f
 
 /* set tx and tx_clk to "No delay adjustment" to keep 0ns
- * dealy
+ * delay
  */
 #define TX_ND                          0x7
 #define TX_CLK_ND                      0xf
@@ -1913,7 +1913,7 @@ static int ksz886x_config_aneg(struct phy_device *phydev)
                return ret;
 
        if (phydev->autoneg != AUTONEG_ENABLE) {
-               /* When autonegotation is disabled, we need to manually force
+               /* When autonegotiation is disabled, we need to manually force
                 * the link state. If we don't do this, the PHY will keep
                 * sending Fast Link Pulses (FLPs) which are part of the
                 * autonegotiation process. This is not desired when
@@ -3533,7 +3533,7 @@ static void lan8814_ptp_disable_event(struct phy_device *phydev, int event)
        /* Set target to too far in the future, effectively disabling it */
        lan8814_ptp_set_target(phydev, event, 0xFFFFFFFF, 0);
 
-       /* And then reload once it recheas the target */
+       /* And then reload once it reaches the target */
        lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, LAN8814_PTP_GENERAL_CONFIG,
                               LAN8814_PTP_GENERAL_CONFIG_RELOAD_ADD_X(event),
                               LAN8814_PTP_GENERAL_CONFIG_RELOAD_ADD_X(event));
@@ -4403,7 +4403,7 @@ static int lan8814_release_coma_mode(struct phy_device *phydev)
 static void lan8814_clear_2psp_bit(struct phy_device *phydev)
 {
        /* It was noticed that when traffic is passing through the PHY and the
-        * cable is removed then the LED was still one even though there is no
+        * cable is removed then the LED was still on even though there is no
         * link
         */
        lanphy_modify_page_reg(phydev, LAN8814_PAGE_PCS_DIGITAL, LAN8814_EEE_STATE,
@@ -4543,7 +4543,7 @@ static int lan8841_config_init(struct phy_device *phydev)
        phy_write_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG,
                      LAN8841_PTP_TX_VERSION, 0xff00);
 
-       /* 100BT Clause 40 improvenent errata */
+       /* 100BT Clause 40 improvement errata */
        phy_write_mmd(phydev, LAN8841_MMD_ANALOG_REG,
                      LAN8841_ANALOG_CONTROL_1,
                      LAN8841_ANALOG_CONTROL_1_PLL_TRIM(0x2));
@@ -5563,7 +5563,7 @@ static int lan8841_ptp_extts_on(struct kszphy_ptp_priv *ptp_priv, int pin,
        u16 tmp = 0;
        int ret;
 
-       /* Set GPIO to be intput */
+       /* Set GPIO to be input */
        ret = phy_set_bits_mmd(phydev, 2, LAN8841_GPIO_EN, BIT(pin));
        if (ret)
                return ret;