SRCDIRS += drivers/bus
SRCDIRS += drivers/net
SRCDIRS += drivers/net/e1000
+SRCDIRS += drivers/net/e1000e
SRCDIRS += drivers/net/phantom
SRCDIRS += drivers/net/rtl818x
SRCDIRS += drivers/net/ath5k
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2008 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_ONLY );
+
+REQUIRE_OBJECT(e1000e_main);
+REQUIRE_OBJECT(e1000e_80003es2lan);
+REQUIRE_OBJECT(e1000e_82571);
+REQUIRE_OBJECT(e1000e_ich8lan);
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+/* Linux PRO/1000 Ethernet Driver main header file */
+
+#ifndef _E1000E_H_
+#define _E1000E_H_
+
+#include <stdint.h>
+#include <stdlib.h>
+#include <stdio.h>
+#include <string.h>
+#include <unistd.h>
+#include <gpxe/io.h>
+#include <errno.h>
+#include <byteswap.h>
+#include <gpxe/pci.h>
+#include <gpxe/malloc.h>
+#include <gpxe/if_ether.h>
+#include <gpxe/ethernet.h>
+#include <gpxe/iobuf.h>
+#include <gpxe/netdevice.h>
+
+/* Begin OS Dependencies */
+
+#define u8 unsigned char
+#define bool boolean_t
+#define dma_addr_t unsigned long
+#define __le16 uint16_t
+#define __le32 uint32_t
+#define __le64 uint64_t
+
+#define __iomem
+
+#define msleep(x) mdelay(x)
+
+#define ETH_FCS_LEN 4
+
+typedef int spinlock_t;
+typedef enum {
+ false = 0,
+ true = 1
+} boolean_t;
+
+/* End OS Dependencies */
+
+#include "e1000e_hw.h"
+
+#define E1000_TX_FLAGS_CSUM 0x00000001
+#define E1000_TX_FLAGS_VLAN 0x00000002
+#define E1000_TX_FLAGS_TSO 0x00000004
+#define E1000_TX_FLAGS_IPV4 0x00000008
+#define E1000_TX_FLAGS_VLAN_MASK 0xffff0000
+#define E1000_TX_FLAGS_VLAN_SHIFT 16
+
+#define E1000_MAX_PER_TXD 8192
+#define E1000_MAX_TXD_PWR 12
+
+#define MINIMUM_DHCP_PACKET_SIZE 282
+
+struct e1000_info;
+
+#define e_dbg(arg...) if (0) { printf (arg); };
+
+#ifdef CONFIG_E1000E_MSIX
+/* Interrupt modes, as used by the IntMode paramter */
+#define E1000E_INT_MODE_LEGACY 0
+#define E1000E_INT_MODE_MSI 1
+#define E1000E_INT_MODE_MSIX 2
+
+#endif /* CONFIG_E1000E_MSIX */
+#ifndef CONFIG_E1000E_NAPI
+#define E1000_MAX_INTR 10
+
+#endif /* CONFIG_E1000E_NAPI */
+/* Tx/Rx descriptor defines */
+#define E1000_DEFAULT_TXD 256
+#define E1000_MAX_TXD 4096
+#define E1000_MIN_TXD 64
+
+#define E1000_DEFAULT_RXD 256
+#define E1000_MAX_RXD 4096
+#define E1000_MIN_RXD 64
+
+#define E1000_MIN_ITR_USECS 10 /* 100000 irq/sec */
+#define E1000_MAX_ITR_USECS 10000 /* 100 irq/sec */
+
+/* Early Receive defines */
+#define E1000_ERT_2048 0x100
+
+#define E1000_FC_PAUSE_TIME 0x0680 /* 858 usec */
+
+/* How many Tx Descriptors do we need to call netif_wake_queue ? */
+/* How many Rx Buffers do we bundle into one write to the hardware ? */
+#define E1000_RX_BUFFER_WRITE 16 /* Must be power of 2 */
+
+#define AUTO_ALL_MODES 0
+#define E1000_EEPROM_APME 0x0400
+
+#define E1000_MNG_VLAN_NONE (-1)
+
+/* Number of packet split data buffers (not including the header buffer) */
+#define PS_PAGE_BUFFERS (MAX_PS_BUFFERS - 1)
+
+#define MAXIMUM_ETHERNET_VLAN_SIZE 1522
+
+#define DEFAULT_JUMBO 9234
+
+enum e1000_boards {
+ board_82571,
+ board_82572,
+ board_82573,
+ board_82574,
+ board_80003es2lan,
+ board_ich8lan,
+ board_ich9lan,
+ board_ich10lan,
+ board_pchlan,
+ board_82583,
+};
+
+/* board specific private data structure */
+struct e1000_adapter {
+ const struct e1000_info *ei;
+
+ /* OS defined structs */
+ struct net_device *netdev;
+ struct pci_device *pdev;
+ struct net_device_stats net_stats;
+
+ /* structs defined in e1000_hw.h */
+ struct e1000_hw hw;
+
+ struct e1000_phy_info phy_info;
+
+ u32 wol;
+ u32 pba;
+ u32 max_hw_frame_size;
+
+ bool fc_autoneg;
+
+ unsigned int flags;
+ unsigned int flags2;
+
+#define NUM_TX_DESC 8
+#define NUM_RX_DESC 8
+
+ struct io_buffer *tx_iobuf[NUM_TX_DESC];
+ struct io_buffer *rx_iobuf[NUM_RX_DESC];
+
+ struct e1000_tx_desc *tx_base;
+ struct e1000_rx_desc *rx_base;
+
+ uint32_t tx_ring_size;
+ uint32_t rx_ring_size;
+
+ uint32_t tx_head;
+ uint32_t tx_tail;
+ uint32_t tx_fill_ctr;
+
+ uint32_t rx_curr;
+
+ uint32_t ioaddr;
+ uint32_t irqno;
+
+ uint32_t tx_int_delay;
+ uint32_t tx_abs_int_delay;
+ uint32_t txd_cmd;
+};
+
+struct e1000_info {
+ enum e1000_mac_type mac;
+ unsigned int flags;
+ unsigned int flags2;
+ u32 pba;
+ u32 max_hw_frame_size;
+ s32 (*get_variants)(struct e1000_adapter *);
+ void (*init_ops)(struct e1000_hw *);
+};
+
+/* hardware capability, feature, and workaround flags */
+#define FLAG_HAS_AMT (1 << 0)
+#define FLAG_HAS_FLASH (1 << 1)
+#define FLAG_HAS_HW_VLAN_FILTER (1 << 2)
+#define FLAG_HAS_WOL (1 << 3)
+#define FLAG_HAS_ERT (1 << 4)
+#define FLAG_HAS_CTRLEXT_ON_LOAD (1 << 5)
+#define FLAG_HAS_SWSM_ON_LOAD (1 << 6)
+#define FLAG_HAS_JUMBO_FRAMES (1 << 7)
+#define FLAG_IS_ICH (1 << 9)
+#ifdef CONFIG_E1000E_MSIX
+#define FLAG_HAS_MSIX (1 << 10)
+#endif
+#define FLAG_HAS_SMART_POWER_DOWN (1 << 11)
+#define FLAG_IS_QUAD_PORT_A (1 << 12)
+#define FLAG_IS_QUAD_PORT (1 << 13)
+#define FLAG_TIPG_MEDIUM_FOR_80003ESLAN (1 << 14)
+#define FLAG_APME_IN_WUC (1 << 15)
+#define FLAG_APME_IN_CTRL3 (1 << 16)
+#define FLAG_APME_CHECK_PORT_B (1 << 17)
+#define FLAG_DISABLE_FC_PAUSE_TIME (1 << 18)
+#define FLAG_NO_WAKE_UCAST (1 << 19)
+#define FLAG_MNG_PT_ENABLED (1 << 20)
+#define FLAG_RESET_OVERWRITES_LAA (1 << 21)
+#define FLAG_TARC_SPEED_MODE_BIT (1 << 22)
+#define FLAG_TARC_SET_BIT_ZERO (1 << 23)
+#define FLAG_RX_NEEDS_RESTART (1 << 24)
+#define FLAG_LSC_GIG_SPEED_DROP (1 << 25)
+#define FLAG_SMART_POWER_DOWN (1 << 26)
+#define FLAG_MSI_ENABLED (1 << 27)
+#define FLAG_RX_CSUM_ENABLED (1 << 28)
+#define FLAG_TSO_FORCE (1 << 29)
+#define FLAG_RX_RESTART_NOW (1 << 30)
+#define FLAG_MSI_TEST_FAILED (1 << 31)
+
+/* CRC Stripping defines */
+#define FLAG2_CRC_STRIPPING (1 << 0)
+#define FLAG2_HAS_PHY_WAKEUP (1 << 1)
+
+#define E1000_RX_DESC_PS(R, i) \
+ (&(((union e1000_rx_desc_packet_split *)((R).desc))[i]))
+#define E1000_GET_DESC(R, i, type) (&(((struct type *)((R).desc))[i]))
+#define E1000_RX_DESC(R, i) E1000_GET_DESC(R, i, e1000_rx_desc)
+#define E1000_TX_DESC(R, i) E1000_GET_DESC(R, i, e1000_tx_desc)
+#define E1000_CONTEXT_DESC(R, i) E1000_GET_DESC(R, i, e1000_context_desc)
+
+enum e1000_state_t {
+ __E1000E_TESTING,
+ __E1000E_RESETTING,
+ __E1000E_DOWN
+};
+
+enum latency_range {
+ lowest_latency = 0,
+ low_latency = 1,
+ bulk_latency = 2,
+ latency_invalid = 255
+};
+
+extern void e1000e_check_options(struct e1000_adapter *adapter);
+
+extern void e1000e_reset(struct e1000_adapter *adapter);
+extern void e1000e_power_up_phy(struct e1000_adapter *adapter);
+
+extern void e1000e_init_function_pointers_82571(struct e1000_hw *hw)
+ __attribute__((weak));
+extern void e1000e_init_function_pointers_80003es2lan(struct e1000_hw *hw)
+ __attribute__((weak));
+extern void e1000e_init_function_pointers_ich8lan(struct e1000_hw *hw)
+ __attribute__((weak));
+
+extern int e1000e_probe(struct pci_device *pdev,
+ const struct pci_device_id *id __unused);
+
+extern void e1000e_remove(struct pci_device *pdev);
+
+extern s32 e1000e_read_pba_num(struct e1000_hw *hw, u32 *pba_num);
+
+static inline s32 e1000e_commit_phy(struct e1000_hw *hw)
+{
+ if (hw->phy.ops.commit)
+ return hw->phy.ops.commit(hw);
+
+ return 0;
+}
+
+extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
+
+extern bool e1000e_get_laa_state_82571(struct e1000_hw *hw);
+extern void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state);
+
+extern void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
+ bool state);
+extern void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
+extern void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw);
+extern void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw);
+
+extern s32 e1000e_check_for_copper_link(struct e1000_hw *hw);
+extern s32 e1000e_check_for_fiber_link(struct e1000_hw *hw);
+extern s32 e1000e_check_for_serdes_link(struct e1000_hw *hw);
+extern s32 e1000e_cleanup_led_generic(struct e1000_hw *hw);
+extern s32 e1000e_led_on_generic(struct e1000_hw *hw);
+extern s32 e1000e_led_off_generic(struct e1000_hw *hw);
+extern s32 e1000e_get_bus_info_pcie(struct e1000_hw *hw);
+extern s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed, u16 *duplex);
+extern s32 e1000e_get_speed_and_duplex_fiber_serdes(struct e1000_hw *hw, u16 *speed, u16 *duplex);
+extern s32 e1000e_disable_pcie_master(struct e1000_hw *hw);
+extern s32 e1000e_get_auto_rd_done(struct e1000_hw *hw);
+extern s32 e1000e_id_led_init(struct e1000_hw *hw);
+extern void e1000e_clear_hw_cntrs_base(struct e1000_hw *hw);
+extern s32 e1000e_setup_fiber_serdes_link(struct e1000_hw *hw);
+extern s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw);
+extern s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw);
+extern s32 e1000e_setup_link(struct e1000_hw *hw);
+static inline void e1000e_clear_vfta(struct e1000_hw *hw)
+{
+ hw->mac.ops.clear_vfta(hw);
+}
+extern void e1000e_init_rx_addrs(struct e1000_hw *hw, u16 rar_count);
+extern void e1000e_update_mc_addr_list_generic(struct e1000_hw *hw,
+ u8 *mc_addr_list,
+ u32 mc_addr_count);
+extern void e1000e_rar_set(struct e1000_hw *hw, u8 *addr, u32 index);
+extern s32 e1000e_set_fc_watermarks(struct e1000_hw *hw);
+extern void e1000e_set_pcie_no_snoop(struct e1000_hw *hw, u32 no_snoop);
+extern s32 e1000e_get_hw_semaphore(struct e1000_hw *hw);
+extern s32 e1000e_valid_led_default(struct e1000_hw *hw, u16 *data);
+extern void e1000e_config_collision_dist(struct e1000_hw *hw);
+extern s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw);
+extern s32 e1000e_force_mac_fc(struct e1000_hw *hw);
+extern s32 e1000e_blink_led(struct e1000_hw *hw);
+extern void e1000e_write_vfta_generic(struct e1000_hw *hw, u32 offset, u32 value);
+static inline void e1000e_write_vfta(struct e1000_hw *hw, u32 offset, u32 value)
+{
+ if (hw->mac.ops.write_vfta)
+ hw->mac.ops.write_vfta(hw, offset, value);
+}
+extern void e1000e_reset_adaptive(struct e1000_hw *hw);
+extern void e1000e_update_adaptive(struct e1000_hw *hw);
+
+extern s32 e1000e_setup_copper_link(struct e1000_hw *hw);
+extern void e1000e_put_hw_semaphore(struct e1000_hw *hw);
+extern s32 e1000e_check_reset_block_generic(struct e1000_hw *hw);
+#if 0
+extern s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw);
+#endif
+#if 0
+extern s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw);
+#endif
+extern s32 e1000e_get_phy_info_igp(struct e1000_hw *hw);
+extern s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw);
+extern s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active);
+extern s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000e_phy_sw_reset(struct e1000_hw *hw);
+#if 0
+extern s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw);
+#endif
+extern s32 e1000e_get_cfg_done(struct e1000_hw *hw);
+#if 0
+extern s32 e1000e_get_cable_length_m88(struct e1000_hw *hw);
+#endif
+extern s32 e1000e_get_phy_info_m88(struct e1000_hw *hw);
+extern s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data);
+extern enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id);
+extern s32 e1000e_determine_phy_address(struct e1000_hw *hw);
+extern s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data);
+#if 0
+extern void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl);
+#endif
+extern s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
+ u32 usec_interval, bool *success);
+extern s32 e1000e_phy_reset_dsp(struct e1000_hw *hw);
+extern s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000e_check_downshift(struct e1000_hw *hw);
+
+static inline s32 e1000e_phy_hw_reset(struct e1000_hw *hw)
+{
+ if (hw->phy.ops.reset)
+ return hw->phy.ops.reset(hw);
+
+ return 0;
+}
+
+static inline s32 e1000e_check_reset_block(struct e1000_hw *hw)
+{
+ if (hw->phy.ops.check_reset_block)
+ return hw->phy.ops.check_reset_block(hw);
+
+ return 0;
+}
+
+static inline s32 e1e_rphy(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ if (hw->phy.ops.read_reg)
+ return hw->phy.ops.read_reg(hw, offset, data);
+
+ return 0;
+}
+
+static inline s32 e1e_wphy(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ if (hw->phy.ops.write_reg)
+ return hw->phy.ops.write_reg(hw, offset, data);
+
+ return 0;
+}
+
+#if 0
+static inline s32 e1000e_get_cable_length(struct e1000_hw *hw)
+{
+ if (hw->phy.ops.get_cable_length)
+ return hw->phy.ops.get_cable_length(hw);
+
+ return 0;
+}
+#endif
+
+extern s32 e1000e_acquire_nvm(struct e1000_hw *hw);
+extern s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
+extern s32 e1000e_update_nvm_checksum_generic(struct e1000_hw *hw);
+extern s32 e1000e_poll_eerd_eewr_done(struct e1000_hw *hw, int ee_reg);
+extern s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
+extern s32 e1000e_validate_nvm_checksum_generic(struct e1000_hw *hw);
+extern void e1000e_release_nvm(struct e1000_hw *hw);
+
+static inline s32 e1000e_read_mac_addr(struct e1000_hw *hw)
+{
+ if (hw->mac.ops.read_mac_addr)
+ return hw->mac.ops.read_mac_addr(hw);
+
+ return e1000e_read_mac_addr_generic(hw);
+}
+
+static inline s32 e1000e_validate_nvm_checksum(struct e1000_hw *hw)
+{
+ return hw->nvm.ops.validate(hw);
+}
+
+static inline s32 e1000e_update_nvm_checksum(struct e1000_hw *hw)
+{
+ return hw->nvm.ops.update(hw);
+}
+
+static inline s32 e1000e_read_nvm(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ return hw->nvm.ops.read(hw, offset, words, data);
+}
+
+static inline s32 e1000e_write_nvm(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ return hw->nvm.ops.write(hw, offset, words, data);
+}
+
+static inline s32 e1000e_get_phy_info(struct e1000_hw *hw)
+{
+ if (hw->phy.ops.get_info)
+ return hw->phy.ops.get_info(hw);
+
+ return 0;
+}
+
+extern bool e1000e_enable_tx_pkt_filtering(struct e1000_hw *hw);
+#if 0
+extern s32 e1000e_mng_write_dhcp_info(struct e1000_hw *hw, u8 *buffer, u16 length);
+#endif
+
+static inline u32 __er32(struct e1000_hw *hw, unsigned long reg)
+{
+ return readl(hw->hw_addr + reg);
+}
+
+static inline void __ew32(struct e1000_hw *hw, unsigned long reg, u32 val)
+{
+ writel(val, hw->hw_addr + reg);
+}
+
+#define er32(reg) __er32(hw, E1000_##reg)
+#define ew32(reg, val) __ew32(hw, E1000_##reg, (val))
+#define e1e_flush() er32(STATUS)
+
+#define E1000_WRITE_REG(a, reg, value) \
+ writel((value), ((a)->hw_addr + reg))
+
+#define E1000_READ_REG(a, reg) (readl((a)->hw_addr + reg))
+
+#define E1000_WRITE_REG_ARRAY(a, reg, offset, value) \
+ writel((value), ((a)->hw_addr + reg + ((offset) << 2)))
+
+#define E1000_READ_REG_ARRAY(a, reg, offset) ( \
+ readl((a)->hw_addr + reg + ((offset) << 2)))
+
+#define E1000_READ_REG_ARRAY_DWORD E1000_READ_REG_ARRAY
+#define E1000_WRITE_REG_ARRAY_DWORD E1000_WRITE_REG_ARRAY
+
+static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg)
+{
+ return readw(hw->flash_address + reg);
+}
+
+static inline u32 __er32flash(struct e1000_hw *hw, unsigned long reg)
+{
+ return readl(hw->flash_address + reg);
+}
+
+static inline void __ew16flash(struct e1000_hw *hw, unsigned long reg, u16 val)
+{
+ writew(val, hw->flash_address + reg);
+}
+
+static inline void __ew32flash(struct e1000_hw *hw, unsigned long reg, u32 val)
+{
+ writel(val, hw->flash_address + reg);
+}
+
+#define er16flash(reg) __er16flash(hw, (reg))
+#define er32flash(reg) __er32flash(hw, (reg))
+#define ew16flash(reg, val) __ew16flash(hw, (reg), (val))
+#define ew32flash(reg, val) __ew32flash(hw, (reg), (val))
+
+#endif /* _E1000E_H_ */
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+/*
+ * 80003ES2LAN Gigabit Ethernet Controller (Copper)
+ * 80003ES2LAN Gigabit Ethernet Controller (Serdes)
+ */
+
+#include "e1000e.h"
+
+static s32 e1000e_init_phy_params_80003es2lan(struct e1000_hw *hw);
+static s32 e1000e_init_nvm_params_80003es2lan(struct e1000_hw *hw);
+static s32 e1000e_init_mac_params_80003es2lan(struct e1000_hw *hw);
+static s32 e1000e_acquire_phy_80003es2lan(struct e1000_hw *hw);
+static void e1000e_release_phy_80003es2lan(struct e1000_hw *hw);
+static s32 e1000e_acquire_nvm_80003es2lan(struct e1000_hw *hw);
+static void e1000e_release_nvm_80003es2lan(struct e1000_hw *hw);
+static s32 e1000e_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
+ u32 offset,
+ u16 *data);
+static s32 e1000e_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
+ u32 offset,
+ u16 data);
+static s32 e1000e_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data);
+static s32 e1000e_get_cfg_done_80003es2lan(struct e1000_hw *hw);
+#if 0
+static s32 e1000e_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw);
+#endif
+#if 0
+static s32 e1000e_get_cable_length_80003es2lan(struct e1000_hw *hw);
+#endif
+static s32 e1000e_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex);
+static s32 e1000e_reset_hw_80003es2lan(struct e1000_hw *hw);
+static s32 e1000e_init_hw_80003es2lan(struct e1000_hw *hw);
+static s32 e1000e_setup_copper_link_80003es2lan(struct e1000_hw *hw);
+static void e1000e_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw);
+static s32 e1000e_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask);
+static s32 e1000e_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex);
+static s32 e1000e_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw);
+static s32 e1000e_cfg_on_link_up_80003es2lan(struct e1000_hw *hw);
+static s32 e1000e_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+ u16 *data);
+static s32 e1000e_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+ u16 data);
+static s32 e1000e_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw);
+static void e1000e_initialize_hw_bits_80003es2lan(struct e1000_hw *hw);
+static void e1000e_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask);
+static s32 e1000e_read_mac_addr_80003es2lan(struct e1000_hw *hw);
+static void e1000e_power_down_phy_copper_80003es2lan(struct e1000_hw *hw);
+
+#if 0
+/*
+ * A table for the GG82563 cable length where the range is defined
+ * with a lower bound at "index" and the upper bound at
+ * "index + 5".
+ */
+static const u16 e1000_gg82563_cable_length_table[] =
+ { 0, 60, 115, 150, 150, 60, 115, 150, 180, 180, 0xFF };
+#define GG82563_CABLE_LENGTH_TABLE_SIZE \
+ (sizeof(e1000_gg82563_cable_length_table) / \
+ sizeof(e1000_gg82563_cable_length_table[0]))
+#endif
+
+/**
+ * e1000e_init_phy_params_80003es2lan - Init ESB2 PHY func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000e_init_phy_params_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+
+ if (hw->phy.media_type != e1000_media_type_copper) {
+ phy->type = e1000_phy_none;
+ goto out;
+ } else {
+ phy->ops.power_up = e1000e_power_up_phy_copper;
+ phy->ops.power_down = e1000e_power_down_phy_copper_80003es2lan;
+ }
+
+ phy->addr = 1;
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ phy->reset_delay_us = 100;
+ phy->type = e1000_phy_gg82563;
+
+ phy->ops.acquire = e1000e_acquire_phy_80003es2lan;
+ phy->ops.check_polarity = e1000e_check_polarity_m88;
+ phy->ops.check_reset_block = e1000e_check_reset_block_generic;
+ phy->ops.commit = e1000e_phy_sw_reset;
+ phy->ops.get_cfg_done = e1000e_get_cfg_done_80003es2lan;
+ phy->ops.get_info = e1000e_get_phy_info_m88;
+ phy->ops.release = e1000e_release_phy_80003es2lan;
+ phy->ops.reset = e1000e_phy_hw_reset_generic;
+ phy->ops.set_d3_lplu_state = e1000e_set_d3_lplu_state;
+#if 0
+ phy->ops.force_speed_duplex = e1000e_phy_force_speed_duplex_80003es2lan;
+#endif
+#if 0
+ phy->ops.get_cable_length = e1000e_get_cable_length_80003es2lan;
+#endif
+ phy->ops.read_reg = e1000e_read_phy_reg_gg82563_80003es2lan;
+ phy->ops.write_reg = e1000e_write_phy_reg_gg82563_80003es2lan;
+
+ phy->ops.cfg_on_link_up = e1000e_cfg_on_link_up_80003es2lan;
+
+ /* This can only be done after all function pointers are setup. */
+ ret_val = e1000e_get_phy_id(hw);
+
+ /* Verify phy id */
+ if (phy->id != GG82563_E_PHY_ID) {
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_init_nvm_params_80003es2lan - Init ESB2 NVM func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000e_init_nvm_params_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 eecd = er32(EECD);
+ u16 size;
+
+ nvm->opcode_bits = 8;
+ nvm->delay_usec = 1;
+ switch (nvm->override) {
+ case e1000_nvm_override_spi_large:
+ nvm->page_size = 32;
+ nvm->address_bits = 16;
+ break;
+ case e1000_nvm_override_spi_small:
+ nvm->page_size = 8;
+ nvm->address_bits = 8;
+ break;
+ default:
+ nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
+ nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
+ break;
+ }
+
+ nvm->type = e1000_nvm_eeprom_spi;
+
+ size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
+ E1000_EECD_SIZE_EX_SHIFT);
+
+ /*
+ * Added to a constant, "size" becomes the left-shift value
+ * for setting word_size.
+ */
+ size += NVM_WORD_SIZE_BASE_SHIFT;
+
+ /* EEPROM access above 16k is unsupported */
+ if (size > 14)
+ size = 14;
+ nvm->word_size = 1 << size;
+
+ /* Function Pointers */
+ nvm->ops.acquire = e1000e_acquire_nvm_80003es2lan;
+ nvm->ops.read = e1000e_read_nvm_eerd;
+ nvm->ops.release = e1000e_release_nvm_80003es2lan;
+ nvm->ops.update = e1000e_update_nvm_checksum_generic;
+ nvm->ops.valid_led_default = e1000e_valid_led_default;
+ nvm->ops.validate = e1000e_validate_nvm_checksum_generic;
+ nvm->ops.write = e1000e_write_nvm_80003es2lan;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_init_mac_params_80003es2lan - Init ESB2 MAC func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000e_init_mac_params_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val = E1000_SUCCESS;
+
+ /* Set media type */
+ switch (hw->device_id) {
+ case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+ break;
+ default:
+ hw->phy.media_type = e1000_media_type_copper;
+ break;
+ }
+
+ /* Set mta register count */
+ mac->mta_reg_count = 128;
+ /* Set rar entry count */
+ mac->rar_entry_count = E1000_RAR_ENTRIES;
+ /* Set if part includes ASF firmware */
+ mac->asf_firmware_present = true;
+ /* Set if manageability features are enabled. */
+ mac->arc_subsystem_valid =
+ (er32(FWSM) & E1000_FWSM_MODE_MASK)
+ ? true : false;
+
+ /* Function pointers */
+
+ /* bus type/speed/width */
+ mac->ops.get_bus_info = e1000e_get_bus_info_pcie;
+ /* reset */
+ mac->ops.reset_hw = e1000e_reset_hw_80003es2lan;
+ /* hw initialization */
+ mac->ops.init_hw = e1000e_init_hw_80003es2lan;
+ /* link setup */
+ mac->ops.setup_link = e1000e_setup_link;
+ /* physical interface link setup */
+ mac->ops.setup_physical_interface =
+ (hw->phy.media_type == e1000_media_type_copper)
+ ? e1000e_setup_copper_link_80003es2lan
+ : e1000e_setup_fiber_serdes_link;
+ /* check for link */
+ switch (hw->phy.media_type) {
+ case e1000_media_type_copper:
+ mac->ops.check_for_link = e1000e_check_for_copper_link;
+ break;
+ case e1000_media_type_fiber:
+ mac->ops.check_for_link = e1000e_check_for_fiber_link;
+ break;
+ case e1000_media_type_internal_serdes:
+ mac->ops.check_for_link = e1000e_check_for_serdes_link;
+ break;
+ default:
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ break;
+ }
+ /* check management mode */
+#if 0
+ mac->ops.check_mng_mode = e1000e_check_mng_mode_generic;
+#endif
+ /* multicast address update */
+ mac->ops.update_mc_addr_list = e1000e_update_mc_addr_list_generic;
+ /* writing VFTA */
+ mac->ops.write_vfta = e1000e_write_vfta_generic;
+ /* clearing VFTA */
+ mac->ops.clear_vfta = e1000e_clear_vfta_generic;
+ /* setting MTA */
+ mac->ops.mta_set = e1000e_mta_set_generic;
+ /* read mac address */
+ mac->ops.read_mac_addr = e1000e_read_mac_addr_80003es2lan;
+ /* ID LED init */
+ mac->ops.id_led_init = e1000e_id_led_init;
+ /* blink LED */
+ mac->ops.blink_led = e1000e_blink_led;
+ /* setup LED */
+ mac->ops.setup_led = e1000e_setup_led_generic;
+ /* cleanup LED */
+ mac->ops.cleanup_led = e1000e_cleanup_led_generic;
+ /* turn on/off LED */
+ mac->ops.led_on = e1000e_led_on_generic;
+ mac->ops.led_off = e1000e_led_off_generic;
+ /* clear hardware counters */
+ mac->ops.clear_hw_cntrs = e1000e_clear_hw_cntrs_80003es2lan;
+ /* link info */
+ mac->ops.get_link_up_info = e1000e_get_link_up_info_80003es2lan;
+
+ /* set lan id for port to determine which phy lock to use */
+ hw->mac.ops.set_lan_id(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_init_function_pointers_80003es2lan - Init ESB2 func ptrs.
+ * @hw: pointer to the HW structure
+ *
+ * Called to initialize all function pointers and parameters.
+ **/
+void e1000e_init_function_pointers_80003es2lan(struct e1000_hw *hw)
+{
+ e1000e_init_mac_ops_generic(hw);
+ e1000e_init_nvm_ops_generic(hw);
+ hw->mac.ops.init_params = e1000e_init_mac_params_80003es2lan;
+ hw->nvm.ops.init_params = e1000e_init_nvm_params_80003es2lan;
+ hw->phy.ops.init_params = e1000e_init_phy_params_80003es2lan;
+}
+
+/**
+ * e1000e_acquire_phy_80003es2lan - Acquire rights to access PHY
+ * @hw: pointer to the HW structure
+ *
+ * A wrapper to acquire access rights to the correct PHY.
+ **/
+static s32 e1000e_acquire_phy_80003es2lan(struct e1000_hw *hw)
+{
+ u16 mask;
+
+ mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
+ return e1000e_acquire_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ * e1000e_release_phy_80003es2lan - Release rights to access PHY
+ * @hw: pointer to the HW structure
+ *
+ * A wrapper to release access rights to the correct PHY.
+ **/
+static void e1000e_release_phy_80003es2lan(struct e1000_hw *hw)
+{
+ u16 mask;
+
+ mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
+ e1000e_release_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ * e1000e_acquire_mac_csr_80003es2lan - Acquire rights to access Kumeran register
+ * @hw: pointer to the HW structure
+ *
+ * Acquire the semaphore to access the Kumeran interface.
+ *
+ **/
+static s32 e1000e_acquire_mac_csr_80003es2lan(struct e1000_hw *hw)
+{
+ u16 mask;
+
+ mask = E1000_SWFW_CSR_SM;
+
+ return e1000e_acquire_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ * e1000e_release_mac_csr_80003es2lan - Release rights to access Kumeran Register
+ * @hw: pointer to the HW structure
+ *
+ * Release the semaphore used to access the Kumeran interface
+ **/
+static void e1000e_release_mac_csr_80003es2lan(struct e1000_hw *hw)
+{
+ u16 mask;
+
+ mask = E1000_SWFW_CSR_SM;
+
+ e1000e_release_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ * e1000e_acquire_nvm_80003es2lan - Acquire rights to access NVM
+ * @hw: pointer to the HW structure
+ *
+ * Acquire the semaphore to access the EEPROM.
+ **/
+static s32 e1000e_acquire_nvm_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val;
+
+ ret_val = e1000e_acquire_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000e_acquire_nvm(hw);
+
+ if (ret_val)
+ e1000e_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_release_nvm_80003es2lan - Relinquish rights to access NVM
+ * @hw: pointer to the HW structure
+ *
+ * Release the semaphore used to access the EEPROM.
+ **/
+static void e1000e_release_nvm_80003es2lan(struct e1000_hw *hw)
+{
+ e1000e_release_nvm(hw);
+ e1000e_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
+}
+
+/**
+ * e1000e_acquire_swfw_sync_80003es2lan - Acquire SW/FW semaphore
+ * @hw: pointer to the HW structure
+ * @mask: specifies which semaphore to acquire
+ *
+ * Acquire the SW/FW semaphore to access the PHY or NVM. The mask
+ * will also specify which port we're acquiring the lock for.
+ **/
+static s32 e1000e_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
+{
+ u32 swfw_sync;
+ u32 swmask = mask;
+ u32 fwmask = mask << 16;
+ s32 ret_val = E1000_SUCCESS;
+ s32 i = 0, timeout = 50;
+
+ while (i < timeout) {
+ if (e1000e_get_hw_semaphore(hw)) {
+ ret_val = -E1000_ERR_SWFW_SYNC;
+ goto out;
+ }
+
+ swfw_sync = er32(SW_FW_SYNC);
+ if (!(swfw_sync & (fwmask | swmask)))
+ break;
+
+ /*
+ * Firmware currently using resource (fwmask)
+ * or other software thread using resource (swmask)
+ */
+ e1000e_put_hw_semaphore(hw);
+ mdelay(5);
+ i++;
+ }
+
+ if (i == timeout) {
+ e_dbg("Driver can't access resource, SW_FW_SYNC timeout.\n");
+ ret_val = -E1000_ERR_SWFW_SYNC;
+ goto out;
+ }
+
+ swfw_sync |= swmask;
+ ew32(SW_FW_SYNC, swfw_sync);
+
+ e1000e_put_hw_semaphore(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_release_swfw_sync_80003es2lan - Release SW/FW semaphore
+ * @hw: pointer to the HW structure
+ * @mask: specifies which semaphore to acquire
+ *
+ * Release the SW/FW semaphore used to access the PHY or NVM. The mask
+ * will also specify which port we're releasing the lock for.
+ **/
+static void e1000e_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
+{
+ u32 swfw_sync;
+
+ while (e1000e_get_hw_semaphore(hw) != E1000_SUCCESS)
+ ; /* Empty */
+
+ swfw_sync = er32(SW_FW_SYNC);
+ swfw_sync &= ~mask;
+ ew32(SW_FW_SYNC, swfw_sync);
+
+ e1000e_put_hw_semaphore(hw);
+}
+
+/**
+ * e1000e_read_phy_reg_gg82563_80003es2lan - Read GG82563 PHY register
+ * @hw: pointer to the HW structure
+ * @offset: offset of the register to read
+ * @data: pointer to the data returned from the operation
+ *
+ * Read the GG82563 PHY register.
+ **/
+static s32 e1000e_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
+ u32 offset, u16 *data)
+{
+ s32 ret_val;
+ u32 page_select;
+ u16 temp;
+
+ ret_val = e1000e_acquire_phy_80003es2lan(hw);
+ if (ret_val)
+ goto out;
+
+ /* Select Configuration Page */
+ if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
+ page_select = GG82563_PHY_PAGE_SELECT;
+ } else {
+ /*
+ * Use Alternative Page Select register to access
+ * registers 30 and 31
+ */
+ page_select = GG82563_PHY_PAGE_SELECT_ALT;
+ }
+
+ temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
+ if (ret_val) {
+ e1000e_release_phy_80003es2lan(hw);
+ goto out;
+ }
+
+ if (hw->dev_spec._80003es2lan.mdic_wa_enable == true) {
+ /*
+ * The "ready" bit in the MDIC register may be incorrectly set
+ * before the device has completed the "Page Select" MDI
+ * transaction. So we wait 200us after each MDI command...
+ */
+ udelay(200);
+
+ /* ...and verify the command was successful. */
+ ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
+
+ if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
+ ret_val = -E1000_ERR_PHY;
+ e1000e_release_phy_80003es2lan(hw);
+ goto out;
+ }
+
+ udelay(200);
+
+ ret_val = e1000e_read_phy_reg_mdic(hw,
+ MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ udelay(200);
+ } else
+ ret_val = e1000e_read_phy_reg_mdic(hw,
+ MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ e1000e_release_phy_80003es2lan(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_write_phy_reg_gg82563_80003es2lan - Write GG82563 PHY register
+ * @hw: pointer to the HW structure
+ * @offset: offset of the register to read
+ * @data: value to write to the register
+ *
+ * Write to the GG82563 PHY register.
+ **/
+static s32 e1000e_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
+ u32 offset, u16 data)
+{
+ s32 ret_val;
+ u32 page_select;
+ u16 temp;
+
+ ret_val = e1000e_acquire_phy_80003es2lan(hw);
+ if (ret_val)
+ goto out;
+
+ /* Select Configuration Page */
+ if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
+ page_select = GG82563_PHY_PAGE_SELECT;
+ } else {
+ /*
+ * Use Alternative Page Select register to access
+ * registers 30 and 31
+ */
+ page_select = GG82563_PHY_PAGE_SELECT_ALT;
+ }
+
+ temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
+ if (ret_val) {
+ e1000e_release_phy_80003es2lan(hw);
+ goto out;
+ }
+
+ if (hw->dev_spec._80003es2lan.mdic_wa_enable == true) {
+ /*
+ * The "ready" bit in the MDIC register may be incorrectly set
+ * before the device has completed the "Page Select" MDI
+ * transaction. So we wait 200us after each MDI command...
+ */
+ udelay(200);
+
+ /* ...and verify the command was successful. */
+ ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
+
+ if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
+ ret_val = -E1000_ERR_PHY;
+ e1000e_release_phy_80003es2lan(hw);
+ goto out;
+ }
+
+ udelay(200);
+
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ udelay(200);
+ } else
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ e1000e_release_phy_80003es2lan(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_write_nvm_80003es2lan - Write to ESB2 NVM
+ * @hw: pointer to the HW structure
+ * @offset: offset of the register to read
+ * @words: number of words to write
+ * @data: buffer of data to write to the NVM
+ *
+ * Write "words" of data to the ESB2 NVM.
+ **/
+static s32 e1000e_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data)
+{
+ return e1000e_write_nvm_spi(hw, offset, words, data);
+}
+
+/**
+ * e1000e_get_cfg_done_80003es2lan - Wait for configuration to complete
+ * @hw: pointer to the HW structure
+ *
+ * Wait a specific amount of time for manageability processes to complete.
+ * This is a function pointer entry point called by the phy module.
+ **/
+static s32 e1000e_get_cfg_done_80003es2lan(struct e1000_hw *hw)
+{
+ s32 timeout = PHY_CFG_TIMEOUT;
+ s32 ret_val = E1000_SUCCESS;
+ u32 mask = E1000_NVM_CFG_DONE_PORT_0;
+
+ if (hw->bus.func == 1)
+ mask = E1000_NVM_CFG_DONE_PORT_1;
+
+ while (timeout) {
+ if (er32(EEMNGCTL) & mask)
+ break;
+ msleep(1);
+ timeout--;
+ }
+ if (!timeout) {
+ e_dbg("MNG configuration cycle has not completed.\n");
+ ret_val = -E1000_ERR_RESET;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+#if 0
+/**
+ * e1000e_phy_force_speed_duplex_80003es2lan - Force PHY speed and duplex
+ * @hw: pointer to the HW structure
+ *
+ * Force the speed and duplex settings onto the PHY. This is a
+ * function pointer entry point called by the phy module.
+ **/
+static s32 e1000e_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 phy_data;
+ bool link;
+
+ if (!(hw->phy.ops.read_reg))
+ goto out;
+
+ /*
+ * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ * forced whenever speed and duplex are forced.
+ */
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_AUTO;
+ ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ goto out;
+
+ e_dbg("GG82563 PSCR: %X\n", phy_data);
+
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
+
+ /* Reset the phy to commit changes. */
+ phy_data |= MII_CR_RESET;
+
+ ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+ if (ret_val)
+ goto out;
+
+ udelay(1);
+
+ if (hw->phy.autoneg_wait_to_complete) {
+ e_dbg("Waiting for forced speed/duplex link "
+ "on GG82563 phy.\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
+ 100000, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link) {
+ /*
+ * We didn't get link.
+ * Reset the DSP and cross our fingers.
+ */
+ ret_val = e1000e_phy_reset_dsp(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
+ 100000, &link);
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Resetting the phy means we need to verify the TX_CLK corresponds
+ * to the link speed. 10Mbps -> 2.5MHz, else 25MHz.
+ */
+ phy_data &= ~GG82563_MSCR_TX_CLK_MASK;
+ if (hw->mac.forced_speed_duplex & E1000_ALL_10_SPEED)
+ phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5;
+ else
+ phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25;
+
+ /*
+ * In addition, we must re-enable CRS on Tx for both half and full
+ * duplex.
+ */
+ phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
+ ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data);
+
+out:
+ return ret_val;
+}
+#endif
+
+#if 0
+/**
+ * e1000e_get_cable_length_80003es2lan - Set approximate cable length
+ * @hw: pointer to the HW structure
+ *
+ * Find the approximate cable length as measured by the GG82563 PHY.
+ * This is a function pointer entry point called by the phy module.
+ **/
+static s32 e1000e_get_cable_length_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+ u16 phy_data, index;
+
+ if (!(hw->phy.ops.read_reg))
+ goto out;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_DSP_DISTANCE, &phy_data);
+ if (ret_val)
+ goto out;
+
+ index = phy_data & GG82563_DSPD_CABLE_LENGTH;
+
+ if (index >= GG82563_CABLE_LENGTH_TABLE_SIZE - 5) {
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+
+ phy->min_cable_length = e1000_gg82563_cable_length_table[index];
+ phy->max_cable_length = e1000_gg82563_cable_length_table[index + 5];
+
+ phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2;
+
+out:
+ return ret_val;
+}
+#endif
+
+/**
+ * e1000e_get_link_up_info_80003es2lan - Report speed and duplex
+ * @hw: pointer to the HW structure
+ * @speed: pointer to speed buffer
+ * @duplex: pointer to duplex buffer
+ *
+ * Retrieve the current speed and duplex configuration.
+ **/
+static s32 e1000e_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex)
+{
+ s32 ret_val;
+
+ if (hw->phy.media_type == e1000_media_type_copper) {
+ ret_val = e1000e_get_speed_and_duplex_copper(hw,
+ speed,
+ duplex);
+ hw->phy.ops.cfg_on_link_up(hw);
+ } else {
+ ret_val = e1000e_get_speed_and_duplex_fiber_serdes(hw,
+ speed,
+ duplex);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_reset_hw_80003es2lan - Reset the ESB2 controller
+ * @hw: pointer to the HW structure
+ *
+ * Perform a global reset to the ESB2 controller.
+ **/
+static s32 e1000e_reset_hw_80003es2lan(struct e1000_hw *hw)
+{
+ u32 ctrl, icr;
+ s32 ret_val;
+
+ /*
+ * Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ ret_val = e1000e_disable_pcie_master(hw);
+ if (ret_val)
+ e_dbg("PCI-E Master disable polling has failed.\n");
+
+ e_dbg("Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ ew32(RCTL, 0);
+ ew32(TCTL, E1000_TCTL_PSP);
+ e1e_flush();
+
+ msleep(10);
+
+ ctrl = er32(CTRL);
+
+ ret_val = e1000e_acquire_phy_80003es2lan(hw);
+ e_dbg("Issuing a global reset to MAC\n");
+ ew32(CTRL, ctrl | E1000_CTRL_RST);
+ e1000e_release_phy_80003es2lan(hw);
+
+ ret_val = e1000e_get_auto_rd_done(hw);
+ if (ret_val)
+ /* We don't want to continue accessing MAC registers. */
+ goto out;
+
+ /* Clear any pending interrupt events. */
+ ew32(IMC, 0xffffffff);
+ icr = er32(ICR);
+
+ ret_val = e1000e_check_alt_mac_addr_generic(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_init_hw_80003es2lan - Initialize the ESB2 controller
+ * @hw: pointer to the HW structure
+ *
+ * Initialize the hw bits, LED, VFTA, MTA, link and hw counters.
+ **/
+static s32 e1000e_init_hw_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 reg_data;
+ s32 ret_val;
+ u16 i;
+
+ e1000e_initialize_hw_bits_80003es2lan(hw);
+
+ /* Initialize identification LED */
+ ret_val = mac->ops.id_led_init(hw);
+ if (ret_val) {
+ e_dbg("Error initializing identification LED\n");
+ /* This is not fatal and we should not stop init due to this */
+ }
+
+ /* Disabling VLAN filtering */
+ e_dbg("Initializing the IEEE VLAN\n");
+ e1000e_clear_vfta(hw);
+
+ /* Setup the receive address. */
+ e1000e_init_rx_addrs(hw, mac->rar_entry_count);
+
+ /* Zero out the Multicast HASH table */
+ e_dbg("Zeroing the MTA\n");
+ for (i = 0; i < mac->mta_reg_count; i++)
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
+
+ /* Setup link and flow control */
+ ret_val = mac->ops.setup_link(hw);
+
+ /* Set the transmit descriptor write-back policy */
+ reg_data = er32(TXDCTL(0));
+ reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC;
+ ew32(TXDCTL(0), reg_data);
+
+ /* ...for both queues. */
+ reg_data = er32(TXDCTL(1));
+ reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC;
+ ew32(TXDCTL(1), reg_data);
+
+ /* Enable retransmit on late collisions */
+ reg_data = er32(TCTL);
+ reg_data |= E1000_TCTL_RTLC;
+ ew32(TCTL, reg_data);
+
+ /* Configure Gigabit Carry Extend Padding */
+ reg_data = er32(TCTL_EXT);
+ reg_data &= ~E1000_TCTL_EXT_GCEX_MASK;
+ reg_data |= DEFAULT_TCTL_EXT_GCEX_80003ES2LAN;
+ ew32(TCTL_EXT, reg_data);
+
+ /* Configure Transmit Inter-Packet Gap */
+ reg_data = er32(TIPG);
+ reg_data &= ~E1000_TIPG_IPGT_MASK;
+ reg_data |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
+ ew32(TIPG, reg_data);
+
+ reg_data = E1000_READ_REG_ARRAY(hw, E1000_FFLT, 0x0001);
+ reg_data &= ~0x00100000;
+ E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data);
+
+ /* default to true to enable the MDIC W/A */
+ hw->dev_spec._80003es2lan.mdic_wa_enable = true;
+
+ ret_val = e1000e_read_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_OFFSET >>
+ E1000_KMRNCTRLSTA_OFFSET_SHIFT,
+ &i);
+ if (!ret_val) {
+ if ((i & E1000_KMRNCTRLSTA_OPMODE_MASK) ==
+ E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO)
+ hw->dev_spec._80003es2lan.mdic_wa_enable = false;
+ }
+
+ /*
+ * Clear all of the statistics registers (clear on read). It is
+ * important that we do this after we have tried to establish link
+ * because the symbol error count will increment wildly if there
+ * is no link.
+ */
+ e1000e_clear_hw_cntrs_80003es2lan(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_initialize_hw_bits_80003es2lan - Init hw bits of ESB2
+ * @hw: pointer to the HW structure
+ *
+ * Initializes required hardware-dependent bits needed for normal operation.
+ **/
+static void e1000e_initialize_hw_bits_80003es2lan(struct e1000_hw *hw)
+{
+ u32 reg;
+
+ /* Transmit Descriptor Control 0 */
+ reg = er32(TXDCTL(0));
+ reg |= (1 << 22);
+ ew32(TXDCTL(0), reg);
+
+ /* Transmit Descriptor Control 1 */
+ reg = er32(TXDCTL(1));
+ reg |= (1 << 22);
+ ew32(TXDCTL(1), reg);
+
+ /* Transmit Arbitration Control 0 */
+ reg = er32(TARC(0));
+ reg &= ~(0xF << 27); /* 30:27 */
+ if (hw->phy.media_type != e1000_media_type_copper)
+ reg &= ~(1 << 20);
+ ew32(TARC(0), reg);
+
+ /* Transmit Arbitration Control 1 */
+ reg = er32(TARC(1));
+ if (er32(TCTL) & E1000_TCTL_MULR)
+ reg &= ~(1 << 28);
+ else
+ reg |= (1 << 28);
+ ew32(TARC(1), reg);
+
+ return;
+}
+
+/**
+ * e1000e_copper_link_setup_gg82563_80003es2lan - Configure GG82563 Link
+ * @hw: pointer to the HW structure
+ *
+ * Setup some GG82563 PHY registers for obtaining link
+ **/
+static s32 e1000e_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u32 ctrl_ext;
+ u16 data;
+
+ if (!phy->reset_disable) {
+ ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
+ /* Use 25MHz for both link down and 1000Base-T for Tx clock. */
+ data |= GG82563_MSCR_TX_CLK_1000MBPS_25;
+
+ ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL,
+ data);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Options:
+ * MDI/MDI-X = 0 (default)
+ * 0 - Auto for all speeds
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+ */
+ ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL, &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;
+
+ switch (phy->mdix) {
+ case 1:
+ data |= GG82563_PSCR_CROSSOVER_MODE_MDI;
+ break;
+ case 2:
+ data |= GG82563_PSCR_CROSSOVER_MODE_MDIX;
+ break;
+ case 0:
+ default:
+ data |= GG82563_PSCR_CROSSOVER_MODE_AUTO;
+ break;
+ }
+
+ /*
+ * Options:
+ * disable_polarity_correction = 0 (default)
+ * Automatic Correction for Reversed Cable Polarity
+ * 0 - Disabled
+ * 1 - Enabled
+ */
+ data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
+ if (phy->disable_polarity_correction)
+ data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
+
+ ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, data);
+ if (ret_val)
+ goto out;
+
+ /* SW Reset the PHY so all changes take effect */
+ ret_val = e1000e_commit_phy(hw);
+ if (ret_val) {
+ e_dbg("Error Resetting the PHY\n");
+ goto out;
+ }
+
+ }
+
+ /* Bypass Rx and Tx FIFO's */
+ ret_val = e1000e_write_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL,
+ E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS |
+ E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000e_read_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE,
+ &data);
+ if (ret_val)
+ goto out;
+ data |= E1000_KMRNCTRLSTA_OPMODE_E_IDLE;
+ ret_val = e1000e_write_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE,
+ data);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL_2, &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG;
+ ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL_2, data);
+ if (ret_val)
+ goto out;
+
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext &= ~(E1000_CTRL_EXT_LINK_MODE_MASK);
+ ew32(CTRL_EXT, ctrl_ext);
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_PWR_MGMT_CTRL, &data);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Do not init these registers when the HW is in IAMT mode, since the
+ * firmware will have already initialized them. We only initialize
+ * them if the HW is not in IAMT mode.
+ */
+ if (!(hw->mac.ops.check_mng_mode(hw))) {
+ /* Enable Electrical Idle on the PHY */
+ data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
+ ret_val = e1e_wphy(hw, GG82563_PHY_PWR_MGMT_CTRL,
+ data);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+ ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL,
+ data);
+ if (ret_val)
+ goto out;
+ }
+
+ /*
+ * Workaround: Disable padding in Kumeran interface in the MAC
+ * and in the PHY to avoid CRC errors.
+ */
+ ret_val = e1e_rphy(hw, GG82563_PHY_INBAND_CTRL, &data);
+ if (ret_val)
+ goto out;
+
+ data |= GG82563_ICR_DIS_PADDING;
+ ret_val = e1e_wphy(hw, GG82563_PHY_INBAND_CTRL, data);
+ if (ret_val)
+ goto out;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_setup_copper_link_80003es2lan - Setup Copper Link for ESB2
+ * @hw: pointer to the HW structure
+ *
+ * Essentially a wrapper for setting up all things "copper" related.
+ * This is a function pointer entry point called by the mac module.
+ **/
+static s32 e1000e_setup_copper_link_80003es2lan(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u16 reg_data;
+
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_SLU;
+ ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ew32(CTRL, ctrl);
+
+ /*
+ * Set the mac to wait the maximum time between each
+ * iteration and increase the max iterations when
+ * polling the phy; this fixes erroneous timeouts at 10Mbps.
+ */
+ ret_val = e1000e_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 4),
+ 0xFFFF);
+ if (ret_val)
+ goto out;
+ ret_val = e1000e_read_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9),
+ ®_data);
+ if (ret_val)
+ goto out;
+ reg_data |= 0x3F;
+ ret_val = e1000e_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9),
+ reg_data);
+ if (ret_val)
+ goto out;
+ ret_val = e1000e_read_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
+ ®_data);
+ if (ret_val)
+ goto out;
+ reg_data |= E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING;
+ ret_val = e1000e_write_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
+ reg_data);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000e_copper_link_setup_gg82563_80003es2lan(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000e_setup_copper_link(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_cfg_on_link_up_80003es2lan - es2 link configuration after link-up
+ * @hw: pointer to the HW structure
+ * @duplex: current duplex setting
+ *
+ * Configure the KMRN interface by applying last minute quirks for
+ * 10/100 operation.
+ **/
+static s32 e1000e_cfg_on_link_up_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 speed;
+ u16 duplex;
+
+ if (hw->phy.media_type == e1000_media_type_copper) {
+ ret_val = e1000e_get_speed_and_duplex_copper(hw,
+ &speed,
+ &duplex);
+ if (ret_val)
+ goto out;
+
+ if (speed == SPEED_1000)
+ ret_val = e1000e_cfg_kmrn_1000_80003es2lan(hw);
+ else
+ ret_val = e1000e_cfg_kmrn_10_100_80003es2lan(hw, duplex);
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_cfg_kmrn_10_100_80003es2lan - Apply "quirks" for 10/100 operation
+ * @hw: pointer to the HW structure
+ * @duplex: current duplex setting
+ *
+ * Configure the KMRN interface by applying last minute quirks for
+ * 10/100 operation.
+ **/
+static s32 e1000e_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u32 tipg;
+ u32 i = 0;
+ u16 reg_data, reg_data2;
+
+ reg_data = E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT;
+ ret_val = e1000e_write_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
+ reg_data);
+ if (ret_val)
+ goto out;
+
+ /* Configure Transmit Inter-Packet Gap */
+ tipg = er32(TIPG);
+ tipg &= ~E1000_TIPG_IPGT_MASK;
+ tipg |= DEFAULT_TIPG_IPGT_10_100_80003ES2LAN;
+ ew32(TIPG, tipg);
+
+
+ do {
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL,
+ ®_data);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL,
+ ®_data2);
+ if (ret_val)
+ goto out;
+ i++;
+ } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));
+
+ if (duplex == HALF_DUPLEX)
+ reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
+ else
+ reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+
+ ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_cfg_kmrn_1000_80003es2lan - Apply "quirks" for gigabit operation
+ * @hw: pointer to the HW structure
+ *
+ * Configure the KMRN interface by applying last minute quirks for
+ * gigabit operation.
+ **/
+static s32 e1000e_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 reg_data, reg_data2;
+ u32 tipg;
+ u32 i = 0;
+
+ reg_data = E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT;
+ ret_val = e1000e_write_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
+ reg_data);
+ if (ret_val)
+ goto out;
+
+ /* Configure Transmit Inter-Packet Gap */
+ tipg = er32(TIPG);
+ tipg &= ~E1000_TIPG_IPGT_MASK;
+ tipg |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
+ ew32(TIPG, tipg);
+
+
+ do {
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL,
+ ®_data);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL,
+ ®_data2);
+ if (ret_val)
+ goto out;
+ i++;
+ } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));
+
+ reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+ ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_kmrn_reg_80003es2lan - Read kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquire semaphore, then read the PHY register at offset
+ * using the kumeran interface. The information retrieved is stored in data.
+ * Release the semaphore before exiting.
+ **/
+static s32 e1000e_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+ u16 *data)
+{
+ u32 kmrnctrlsta;
+ s32 ret_val = E1000_SUCCESS;
+
+ ret_val = e1000e_acquire_mac_csr_80003es2lan(hw);
+ if (ret_val)
+ goto out;
+
+ kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
+ E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN;
+ ew32(KMRNCTRLSTA, kmrnctrlsta);
+
+ udelay(2);
+
+ kmrnctrlsta = er32(KMRNCTRLSTA);
+ *data = (u16)kmrnctrlsta;
+
+ e1000e_release_mac_csr_80003es2lan(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_write_kmrn_reg_80003es2lan - Write kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquire semaphore, then write the data to PHY register
+ * at the offset using the kumeran interface. Release semaphore
+ * before exiting.
+ **/
+static s32 e1000e_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+ u16 data)
+{
+ u32 kmrnctrlsta;
+ s32 ret_val = E1000_SUCCESS;
+
+ ret_val = e1000e_acquire_mac_csr_80003es2lan(hw);
+ if (ret_val)
+ goto out;
+
+ kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
+ E1000_KMRNCTRLSTA_OFFSET) | data;
+ ew32(KMRNCTRLSTA, kmrnctrlsta);
+
+ udelay(2);
+
+ e1000e_release_mac_csr_80003es2lan(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_mac_addr_80003es2lan - Read device MAC address
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000e_read_mac_addr_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ /*
+ * If there's an alternate MAC address place it in RAR0
+ * so that it will override the Si installed default perm
+ * address.
+ */
+ ret_val = e1000e_check_alt_mac_addr_generic(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000e_read_mac_addr_generic(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_power_down_phy_copper_80003es2lan - Remove link during PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, remove the link.
+ **/
+static void e1000e_power_down_phy_copper_80003es2lan(struct e1000_hw *hw)
+{
+ /* If the management interface is not enabled, then power down */
+ if (!(hw->mac.ops.check_mng_mode(hw) ||
+ e1000e_check_reset_block(hw)))
+ e1000e_power_down_phy_copper(hw);
+
+ return;
+}
+
+/**
+ * e1000e_clear_hw_cntrs_80003es2lan - Clear device specific hardware counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears the hardware counters by reading the counter registers.
+ **/
+static void e1000e_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw __unused)
+{
+#if 0
+ e1000e_clear_hw_cntrs_base(hw);
+
+ er32(PRC64);
+ er32(PRC127);
+ er32(PRC255);
+ er32(PRC511);
+ er32(PRC1023);
+ er32(PRC1522);
+ er32(PTC64);
+ er32(PTC127);
+ er32(PTC255);
+ er32(PTC511);
+ er32(PTC1023);
+ er32(PTC1522);
+
+ er32(ALGNERRC);
+ er32(RXERRC);
+ er32(TNCRS);
+ er32(CEXTERR);
+ er32(TSCTC);
+ er32(TSCTFC);
+
+ er32(MGTPRC);
+ er32(MGTPDC);
+ er32(MGTPTC);
+
+ er32(IAC);
+ er32(ICRXOC);
+
+ er32(ICRXPTC);
+ er32(ICRXATC);
+ er32(ICTXPTC);
+ er32(ICTXATC);
+ er32(ICTXQEC);
+ er32(ICTXQMTC);
+ er32(ICRXDMTC);
+#endif
+}
+
+static struct pci_device_id e1000e_80003es2lan_nics[] = {
+ PCI_ROM(0x8086, 0x1096, "E1000_DEV_ID_80003ES2LAN_COPPER_DPT", "E1000_DEV_ID_80003ES2LAN_COPPER_DPT", board_80003es2lan),
+ PCI_ROM(0x8086, 0x10BA, "E1000_DEV_ID_80003ES2LAN_COPPER_SPT", "E1000_DEV_ID_80003ES2LAN_COPPER_SPT", board_80003es2lan),
+ PCI_ROM(0x8086, 0x1098, "E1000_DEV_ID_80003ES2LAN_SERDES_DPT", "E1000_DEV_ID_80003ES2LAN_SERDES_DPT", board_80003es2lan),
+ PCI_ROM(0x8086, 0x10BB, "E1000_DEV_ID_80003ES2LAN_SERDES_SPT", "E1000_DEV_ID_80003ES2LAN_SERDES_SPT", board_80003es2lan),
+};
+
+struct pci_driver e1000e_80003es2lan_driver __pci_driver = {
+ .ids = e1000e_80003es2lan_nics,
+ .id_count = (sizeof (e1000e_80003es2lan_nics) / sizeof (e1000e_80003es2lan_nics[0])),
+ .probe = e1000e_probe,
+ .remove = e1000e_remove,
+};
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#ifndef _E1000E_80003ES2LAN_H_
+#define _E1000E_80003ES2LAN_H_
+
+#define E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL 0x00
+#define E1000_KMRNCTRLSTA_OFFSET_INB_CTRL 0x02
+#define E1000_KMRNCTRLSTA_OFFSET_HD_CTRL 0x10
+#define E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE 0x1F
+
+#define E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS 0x0008
+#define E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS 0x0800
+#define E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING 0x0010
+
+#define E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT 0x0004
+#define E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT 0x0000
+#define E1000_KMRNCTRLSTA_OPMODE_E_IDLE 0x2000
+
+#define E1000_KMRNCTRLSTA_OPMODE_MASK 0x000C
+#define E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO 0x0004
+
+#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */
+#define DEFAULT_TCTL_EXT_GCEX_80003ES2LAN 0x00010000
+
+#define DEFAULT_TIPG_IPGT_1000_80003ES2LAN 0x8
+#define DEFAULT_TIPG_IPGT_10_100_80003ES2LAN 0x9
+
+/* GG82563 PHY Specific Status Register (Page 0, Register 16 */
+#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Reversal Disabled */
+#define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060
+#define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI */
+#define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX */
+#define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Auto crossover */
+
+/* PHY Specific Control Register 2 (Page 0, Register 26) */
+#define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000
+ /* 1=Reverse Auto-Negotiation */
+
+/* MAC Specific Control Register (Page 2, Register 21) */
+/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */
+#define GG82563_MSCR_TX_CLK_MASK 0x0007
+#define GG82563_MSCR_TX_CLK_10MBPS_2_5 0x0004
+#define GG82563_MSCR_TX_CLK_100MBPS_25 0x0005
+#define GG82563_MSCR_TX_CLK_1000MBPS_2_5 0x0006
+#define GG82563_MSCR_TX_CLK_1000MBPS_25 0x0007
+
+#define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */
+
+/* DSP Distance Register (Page 5, Register 26) */
+/*
+ * 0 = <50M
+ * 1 = 50-80M
+ * 2 = 80-100M
+ * 3 = 110-140M
+ * 4 = >140M
+ */
+#define GG82563_DSPD_CABLE_LENGTH 0x0007
+
+/* Kumeran Mode Control Register (Page 193, Register 16) */
+#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800
+
+/* Max number of times Kumeran read/write should be validated */
+#define GG82563_MAX_KMRN_RETRY 0x5
+
+/* Power Management Control Register (Page 193, Register 20) */
+#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001
+ /* 1=Enable SERDES Electrical Idle */
+
+/* In-Band Control Register (Page 194, Register 18) */
+#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding */
+
+#endif
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+/*
+ * 82571EB Gigabit Ethernet Controller
+ * 82571EB Gigabit Ethernet Controller (Copper)
+ * 82571EB Gigabit Ethernet Controller (Fiber)
+ * 82571EB Dual Port Gigabit Mezzanine Adapter
+ * 82571EB Quad Port Gigabit Mezzanine Adapter
+ * 82571PT Gigabit PT Quad Port Server ExpressModule
+ * 82572EI Gigabit Ethernet Controller (Copper)
+ * 82572EI Gigabit Ethernet Controller (Fiber)
+ * 82572EI Gigabit Ethernet Controller
+ * 82573V Gigabit Ethernet Controller (Copper)
+ * 82573E Gigabit Ethernet Controller (Copper)
+ * 82573L Gigabit Ethernet Controller
+ * 82574L Gigabit Network Connection
+ * 82574L Gigabit Network Connection
+ * 82583V Gigabit Network Connection
+ */
+
+#include "e1000e.h"
+
+static s32 e1000e_init_phy_params_82571(struct e1000_hw *hw);
+static s32 e1000e_init_nvm_params_82571(struct e1000_hw *hw);
+static s32 e1000e_init_mac_params_82571(struct e1000_hw *hw);
+static s32 e1000e_acquire_nvm_82571(struct e1000_hw *hw);
+static void e1000e_release_nvm_82571(struct e1000_hw *hw);
+static s32 e1000e_write_nvm_82571(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data);
+static s32 e1000e_update_nvm_checksum_82571(struct e1000_hw *hw);
+static s32 e1000e_validate_nvm_checksum_82571(struct e1000_hw *hw);
+static s32 e1000e_get_cfg_done_82571(struct e1000_hw *hw);
+static s32 e1000e_set_d0_lplu_state_82571(struct e1000_hw *hw,
+ bool active);
+static s32 e1000e_reset_hw_82571(struct e1000_hw *hw);
+static s32 e1000e_init_hw_82571(struct e1000_hw *hw);
+static void e1000e_clear_vfta_82571(struct e1000_hw *hw);
+#if 0
+static bool e1000e_check_mng_mode_82574(struct e1000_hw *hw);
+#endif
+static s32 e1000e_led_on_82574(struct e1000_hw *hw);
+static s32 e1000e_setup_link_82571(struct e1000_hw *hw);
+static s32 e1000e_setup_copper_link_82571(struct e1000_hw *hw);
+static s32 e1000e_check_for_serdes_link_82571(struct e1000_hw *hw);
+static s32 e1000e_setup_fiber_serdes_link_82571(struct e1000_hw *hw);
+static s32 e1000e_valid_led_default_82571(struct e1000_hw *hw, u16 *data);
+static void e1000e_clear_hw_cntrs_82571(struct e1000_hw *hw);
+static s32 e1000e_get_hw_semaphore_82571(struct e1000_hw *hw);
+static s32 e1000e_fix_nvm_checksum_82571(struct e1000_hw *hw);
+static s32 e1000e_get_phy_id_82571(struct e1000_hw *hw);
+static void e1000e_put_hw_semaphore_82571(struct e1000_hw *hw);
+static void e1000e_initialize_hw_bits_82571(struct e1000_hw *hw);
+static s32 e1000e_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data);
+static s32 e1000e_read_mac_addr_82571(struct e1000_hw *hw);
+static void e1000e_power_down_phy_copper_82571(struct e1000_hw *hw);
+
+/**
+ * e1000e_init_phy_params_82571 - Init PHY func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000e_init_phy_params_82571(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+
+ if (hw->phy.media_type != e1000_media_type_copper) {
+ phy->type = e1000_phy_none;
+ goto out;
+ }
+
+ phy->addr = 1;
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ phy->reset_delay_us = 100;
+
+ phy->ops.acquire = e1000e_get_hw_semaphore_82571;
+ phy->ops.check_polarity = e1000e_check_polarity_igp;
+ phy->ops.check_reset_block = e1000e_check_reset_block_generic;
+ phy->ops.release = e1000e_put_hw_semaphore_82571;
+ phy->ops.reset = e1000e_phy_hw_reset_generic;
+ phy->ops.set_d0_lplu_state = e1000e_set_d0_lplu_state_82571;
+ phy->ops.set_d3_lplu_state = e1000e_set_d3_lplu_state;
+ phy->ops.power_up = e1000e_power_up_phy_copper;
+ phy->ops.power_down = e1000e_power_down_phy_copper_82571;
+
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ phy->type = e1000_phy_igp_2;
+ phy->ops.get_cfg_done = e1000e_get_cfg_done_82571;
+ phy->ops.get_info = e1000e_get_phy_info_igp;
+#if 0
+ phy->ops.force_speed_duplex = e1000e_phy_force_speed_duplex_igp;
+#endif
+#if 0
+ phy->ops.get_cable_length = e1000e_get_cable_length_igp_2;
+#endif
+ phy->ops.read_reg = e1000e_read_phy_reg_igp;
+ phy->ops.write_reg = e1000e_write_phy_reg_igp;
+
+ /* This uses above function pointers */
+ ret_val = e1000e_get_phy_id_82571(hw);
+
+ /* Verify PHY ID */
+ if (phy->id != IGP01E1000_I_PHY_ID) {
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+ break;
+ case e1000_82573:
+ phy->type = e1000_phy_m88;
+ phy->ops.get_cfg_done = e1000e_get_cfg_done;
+ phy->ops.get_info = e1000e_get_phy_info_m88;
+ phy->ops.commit = e1000e_phy_sw_reset;
+#if 0
+ phy->ops.force_speed_duplex = e1000e_phy_force_speed_duplex_m88;
+#endif
+#if 0
+ phy->ops.get_cable_length = e1000e_get_cable_length_m88;
+#endif
+ phy->ops.read_reg = e1000e_read_phy_reg_m88;
+ phy->ops.write_reg = e1000e_write_phy_reg_m88;
+
+ /* This uses above function pointers */
+ ret_val = e1000e_get_phy_id_82571(hw);
+
+ /* Verify PHY ID */
+ if (phy->id != M88E1111_I_PHY_ID) {
+ ret_val = -E1000_ERR_PHY;
+ e_dbg("PHY ID unknown: type = 0x%08x\n", phy->id);
+ goto out;
+ }
+ break;
+ case e1000_82583:
+ case e1000_82574:
+ phy->type = e1000_phy_bm;
+ phy->ops.get_cfg_done = e1000e_get_cfg_done;
+ phy->ops.get_info = e1000e_get_phy_info_m88;
+ phy->ops.commit = e1000e_phy_sw_reset;
+#if 0
+ phy->ops.force_speed_duplex = e1000e_phy_force_speed_duplex_m88;
+#endif
+#if 0
+ phy->ops.get_cable_length = e1000e_get_cable_length_m88;
+#endif
+ phy->ops.read_reg = e1000e_read_phy_reg_bm2;
+ phy->ops.write_reg = e1000e_write_phy_reg_bm2;
+
+ /* This uses above function pointers */
+ ret_val = e1000e_get_phy_id_82571(hw);
+ /* Verify PHY ID */
+ if (phy->id != BME1000_E_PHY_ID_R2) {
+ ret_val = -E1000_ERR_PHY;
+ e_dbg("PHY ID unknown: type = 0x%08x\n", phy->id);
+ goto out;
+ }
+ break;
+ default:
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ break;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_init_nvm_params_82571 - Init NVM func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000e_init_nvm_params_82571(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 eecd = er32(EECD);
+ u16 size;
+
+ nvm->opcode_bits = 8;
+ nvm->delay_usec = 1;
+ switch (nvm->override) {
+ case e1000_nvm_override_spi_large:
+ nvm->page_size = 32;
+ nvm->address_bits = 16;
+ break;
+ case e1000_nvm_override_spi_small:
+ nvm->page_size = 8;
+ nvm->address_bits = 8;
+ break;
+ default:
+ nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
+ nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
+ break;
+ }
+
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
+ if (((eecd >> 15) & 0x3) == 0x3) {
+ nvm->type = e1000_nvm_flash_hw;
+ nvm->word_size = 2048;
+ /*
+ * Autonomous Flash update bit must be cleared due
+ * to Flash update issue.
+ */
+ eecd &= ~E1000_EECD_AUPDEN;
+ ew32(EECD, eecd);
+ break;
+ }
+ /* Fall Through */
+ default:
+ nvm->type = e1000_nvm_eeprom_spi;
+ size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
+ E1000_EECD_SIZE_EX_SHIFT);
+ /*
+ * Added to a constant, "size" becomes the left-shift value
+ * for setting word_size.
+ */
+ size += NVM_WORD_SIZE_BASE_SHIFT;
+
+ /* EEPROM access above 16k is unsupported */
+ if (size > 14)
+ size = 14;
+ nvm->word_size = 1 << size;
+ break;
+ }
+
+ /* Function Pointers */
+ nvm->ops.acquire = e1000e_acquire_nvm_82571;
+ nvm->ops.read = e1000e_read_nvm_eerd;
+ nvm->ops.release = e1000e_release_nvm_82571;
+ nvm->ops.update = e1000e_update_nvm_checksum_82571;
+ nvm->ops.validate = e1000e_validate_nvm_checksum_82571;
+ nvm->ops.valid_led_default = e1000e_valid_led_default_82571;
+ nvm->ops.write = e1000e_write_nvm_82571;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_init_mac_params_82571 - Init MAC func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000e_init_mac_params_82571(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val = E1000_SUCCESS;
+ u32 swsm = 0;
+ u32 swsm2 = 0;
+ bool force_clear_smbi = false;
+
+ /* Set media type */
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82571EB_FIBER:
+ case E1000_DEV_ID_82572EI_FIBER:
+ case E1000_DEV_ID_82571EB_QUAD_FIBER:
+ hw->phy.media_type = e1000_media_type_fiber;
+ break;
+ case E1000_DEV_ID_82571EB_SERDES:
+ case E1000_DEV_ID_82571EB_SERDES_DUAL:
+ case E1000_DEV_ID_82571EB_SERDES_QUAD:
+ case E1000_DEV_ID_82572EI_SERDES:
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+ break;
+ default:
+ hw->phy.media_type = e1000_media_type_copper;
+ break;
+ }
+
+ /* Set mta register count */
+ mac->mta_reg_count = 128;
+ /* Set rar entry count */
+ mac->rar_entry_count = E1000_RAR_ENTRIES;
+ /* Set if part includes ASF firmware */
+ mac->asf_firmware_present = true;
+ /* Set if manageability features are enabled. */
+ mac->arc_subsystem_valid =
+ (er32(FWSM) & E1000_FWSM_MODE_MASK)
+ ? true : false;
+
+ /* Function pointers */
+
+ /* bus type/speed/width */
+ mac->ops.get_bus_info = e1000e_get_bus_info_pcie;
+ /* function id */
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
+ mac->ops.set_lan_id = e1000e_set_lan_id_single_port;
+ break;
+ default:
+ break;
+ }
+ /* reset */
+ mac->ops.reset_hw = e1000e_reset_hw_82571;
+ /* hw initialization */
+ mac->ops.init_hw = e1000e_init_hw_82571;
+ /* link setup */
+ mac->ops.setup_link = e1000e_setup_link_82571;
+ /* physical interface link setup */
+ mac->ops.setup_physical_interface =
+ (hw->phy.media_type == e1000_media_type_copper)
+ ? e1000e_setup_copper_link_82571
+ : e1000e_setup_fiber_serdes_link_82571;
+ /* check for link */
+ switch (hw->phy.media_type) {
+ case e1000_media_type_copper:
+ mac->ops.check_for_link = e1000e_check_for_copper_link;
+ break;
+ case e1000_media_type_fiber:
+ mac->ops.check_for_link = e1000e_check_for_fiber_link;
+ break;
+ case e1000_media_type_internal_serdes:
+ mac->ops.check_for_link = e1000e_check_for_serdes_link_82571;
+ break;
+ default:
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ break;
+ }
+ /* check management mode */
+#if 0
+ switch (hw->mac.type) {
+ case e1000_82574:
+ case e1000_82583:
+ mac->ops.check_mng_mode = e1000e_check_mng_mode_82574;
+ break;
+ default:
+ mac->ops.check_mng_mode = e1000e_check_mng_mode_generic;
+ break;
+ }
+#endif
+ /* multicast address update */
+ mac->ops.update_mc_addr_list = e1000e_update_mc_addr_list_generic;
+ /* writing VFTA */
+ mac->ops.write_vfta = e1000e_write_vfta_generic;
+ /* clearing VFTA */
+ mac->ops.clear_vfta = e1000e_clear_vfta_82571;
+ /* setting MTA */
+ mac->ops.mta_set = e1000e_mta_set_generic;
+ /* read mac address */
+ mac->ops.read_mac_addr = e1000e_read_mac_addr_82571;
+ /* ID LED init */
+ mac->ops.id_led_init = e1000e_id_led_init;
+ /* blink LED */
+ mac->ops.blink_led = e1000e_blink_led;
+ /* setup LED */
+ mac->ops.setup_led = e1000e_setup_led_generic;
+ /* cleanup LED */
+ mac->ops.cleanup_led = e1000e_cleanup_led_generic;
+ /* turn on/off LED */
+ switch (hw->mac.type) {
+ case e1000_82574:
+ case e1000_82583:
+ mac->ops.led_on = e1000e_led_on_82574;
+ break;
+ default:
+ mac->ops.led_on = e1000e_led_on_generic;
+ break;
+ }
+ mac->ops.led_off = e1000e_led_off_generic;
+ /* clear hardware counters */
+ mac->ops.clear_hw_cntrs = e1000e_clear_hw_cntrs_82571;
+ /* link info */
+ mac->ops.get_link_up_info =
+ (hw->phy.media_type == e1000_media_type_copper)
+ ? e1000e_get_speed_and_duplex_copper
+ : e1000e_get_speed_and_duplex_fiber_serdes;
+
+ /*
+ * Ensure that the inter-port SWSM.SMBI lock bit is clear before
+ * first NVM or PHY acess. This should be done for single-port
+ * devices, and for one port only on dual-port devices so that
+ * for those devices we can still use the SMBI lock to synchronize
+ * inter-port accesses to the PHY & NVM.
+ */
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ swsm2 = er32(SWSM2);
+
+ if (!(swsm2 & E1000_SWSM2_LOCK)) {
+ /* Only do this for the first interface on this card */
+ ew32(SWSM2,
+ swsm2 | E1000_SWSM2_LOCK);
+ force_clear_smbi = true;
+ } else
+ force_clear_smbi = false;
+ break;
+ default:
+ force_clear_smbi = true;
+ break;
+ }
+
+ if (force_clear_smbi) {
+ /* Make sure SWSM.SMBI is clear */
+ swsm = er32(SWSM);
+ if (swsm & E1000_SWSM_SMBI) {
+ /* This bit should not be set on a first interface, and
+ * indicates that the bootagent or EFI code has
+ * improperly left this bit enabled
+ */
+ e_dbg("Please update your 82571 Bootagent\n");
+ }
+ ew32(SWSM, swsm & ~E1000_SWSM_SMBI);
+ }
+
+ /*
+ * Initialze device specific counter of SMBI acquisition
+ * timeouts.
+ */
+ hw->dev_spec._82571.smb_counter = 0;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_init_function_pointers_82571 - Init func ptrs.
+ * @hw: pointer to the HW structure
+ *
+ * Called to initialize all function pointers and parameters.
+ **/
+void e1000e_init_function_pointers_82571(struct e1000_hw *hw)
+{
+ e1000e_init_mac_ops_generic(hw);
+ e1000e_init_nvm_ops_generic(hw);
+ hw->mac.ops.init_params = e1000e_init_mac_params_82571;
+ hw->nvm.ops.init_params = e1000e_init_nvm_params_82571;
+ hw->phy.ops.init_params = e1000e_init_phy_params_82571;
+}
+
+/**
+ * e1000e_get_phy_id_82571 - Retrieve the PHY ID and revision
+ * @hw: pointer to the HW structure
+ *
+ * Reads the PHY registers and stores the PHY ID and possibly the PHY
+ * revision in the hardware structure.
+ **/
+static s32 e1000e_get_phy_id_82571(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+ u16 phy_id = 0;
+
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ /*
+ * The 82571 firmware may still be configuring the PHY.
+ * In this case, we cannot access the PHY until the
+ * configuration is done. So we explicitly set the
+ * PHY ID.
+ */
+ phy->id = IGP01E1000_I_PHY_ID;
+ break;
+ case e1000_82573:
+ ret_val = e1000e_get_phy_id(hw);
+ break;
+ case e1000_82574:
+ case e1000_82583:
+ ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+ if (ret_val)
+ goto out;
+
+ phy->id = (u32)(phy_id << 16);
+ udelay(20);
+ ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+ if (ret_val)
+ goto out;
+
+ phy->id |= (u32)(phy_id);
+ phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+ break;
+ default:
+ ret_val = -E1000_ERR_PHY;
+ break;
+ }
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_get_hw_semaphore_82571 - Acquire hardware semaphore
+ * @hw: pointer to the HW structure
+ *
+ * Acquire the HW semaphore to access the PHY or NVM
+ **/
+s32 e1000e_get_hw_semaphore_82571(struct e1000_hw *hw)
+{
+ u32 swsm;
+ s32 ret_val = E1000_SUCCESS;
+ s32 sw_timeout = hw->nvm.word_size + 1;
+ s32 fw_timeout = hw->nvm.word_size + 1;
+ s32 i = 0;
+
+ /*
+ * If we have timedout 3 times on trying to acquire
+ * the inter-port SMBI semaphore, there is old code
+ * operating on the other port, and it is not
+ * releasing SMBI. Modify the number of times that
+ * we try for the semaphore to interwork with this
+ * older code.
+ */
+ if (hw->dev_spec._82571.smb_counter > 2)
+ sw_timeout = 1;
+
+ /* Get the SW semaphore */
+ while (i < sw_timeout) {
+ swsm = er32(SWSM);
+ if (!(swsm & E1000_SWSM_SMBI))
+ break;
+
+ udelay(50);
+ i++;
+ }
+
+ if (i == sw_timeout) {
+ e_dbg("Driver can't access device - SMBI bit is set.\n");
+ hw->dev_spec._82571.smb_counter++;
+ }
+ /* Get the FW semaphore. */
+ for (i = 0; i < fw_timeout; i++) {
+ swsm = er32(SWSM);
+ ew32(SWSM, swsm | E1000_SWSM_SWESMBI);
+
+ /* Semaphore acquired if bit latched */
+ if (er32(SWSM) & E1000_SWSM_SWESMBI)
+ break;
+
+ udelay(50);
+ }
+
+ if (i == fw_timeout) {
+ /* Release semaphores */
+ e1000e_put_hw_semaphore_82571(hw);
+ e_dbg("Driver can't access the NVM\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_put_hw_semaphore_82571 - Release hardware semaphore
+ * @hw: pointer to the HW structure
+ *
+ * Release hardware semaphore used to access the PHY or NVM
+ **/
+void e1000e_put_hw_semaphore_82571(struct e1000_hw *hw)
+{
+ u32 swsm;
+
+ swsm = er32(SWSM);
+ swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
+ ew32(SWSM, swsm);
+}
+
+/**
+ * e1000e_acquire_nvm_82571 - Request for access to the EEPROM
+ * @hw: pointer to the HW structure
+ *
+ * To gain access to the EEPROM, first we must obtain a hardware semaphore.
+ * Then for non-82573 hardware, set the EEPROM access request bit and wait
+ * for EEPROM access grant bit. If the access grant bit is not set, release
+ * hardware semaphore.
+ **/
+static s32 e1000e_acquire_nvm_82571(struct e1000_hw *hw)
+{
+ s32 ret_val;
+
+ ret_val = e1000e_get_hw_semaphore_82571(hw);
+ if (ret_val)
+ goto out;
+
+ switch (hw->mac.type) {
+ case e1000_82574:
+ case e1000_82583:
+ case e1000_82573:
+ break;
+ default:
+ ret_val = e1000e_acquire_nvm(hw);
+ break;
+ }
+
+ if (ret_val)
+ e1000e_put_hw_semaphore_82571(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_release_nvm_82571 - Release exclusive access to EEPROM
+ * @hw: pointer to the HW structure
+ *
+ * Stop any current commands to the EEPROM and clear the EEPROM request bit.
+ **/
+static void e1000e_release_nvm_82571(struct e1000_hw *hw)
+{
+ e1000e_release_nvm(hw);
+ e1000e_put_hw_semaphore_82571(hw);
+}
+
+/**
+ * e1000e_write_nvm_82571 - Write to EEPROM using appropriate interface
+ * @hw: pointer to the HW structure
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: 16 bit word(s) to be written to the EEPROM
+ *
+ * For non-82573 silicon, write data to EEPROM at offset using SPI interface.
+ *
+ * If e1000e_update_nvm_checksum is not called after this function, the
+ * EEPROM will most likely contain an invalid checksum.
+ **/
+static s32 e1000e_write_nvm_82571(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
+ ret_val = e1000e_write_nvm_eewr_82571(hw, offset, words, data);
+ break;
+ case e1000_82571:
+ case e1000_82572:
+ ret_val = e1000e_write_nvm_spi(hw, offset, words, data);
+ break;
+ default:
+ ret_val = -E1000_ERR_NVM;
+ break;
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_update_nvm_checksum_82571 - Update EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Updates the EEPROM checksum by reading/adding each word of the EEPROM
+ * up to the checksum. Then calculates the EEPROM checksum and writes the
+ * value to the EEPROM.
+ **/
+static s32 e1000e_update_nvm_checksum_82571(struct e1000_hw *hw)
+{
+ u32 eecd;
+ s32 ret_val;
+ u16 i;
+
+ ret_val = e1000e_update_nvm_checksum_generic(hw);
+ if (ret_val)
+ goto out;
+
+ /*
+ * If our nvm is an EEPROM, then we're done
+ * otherwise, commit the checksum to the flash NVM.
+ */
+ if (hw->nvm.type != e1000_nvm_flash_hw)
+ goto out;
+
+ /* Check for pending operations. */
+ for (i = 0; i < E1000_FLASH_UPDATES; i++) {
+ msleep(1);
+ if ((er32(EECD) & E1000_EECD_FLUPD) == 0)
+ break;
+ }
+
+ if (i == E1000_FLASH_UPDATES) {
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+ /* Reset the firmware if using STM opcode. */
+ if ((er32(FLOP) & 0xFF00) == E1000_STM_OPCODE) {
+ /*
+ * The enabling of and the actual reset must be done
+ * in two write cycles.
+ */
+ ew32(HICR, E1000_HICR_FW_RESET_ENABLE);
+ e1e_flush();
+ ew32(HICR, E1000_HICR_FW_RESET);
+ }
+
+ /* Commit the write to flash */
+ eecd = er32(EECD) | E1000_EECD_FLUPD;
+ ew32(EECD, eecd);
+
+ for (i = 0; i < E1000_FLASH_UPDATES; i++) {
+ msleep(1);
+ if ((er32(EECD) & E1000_EECD_FLUPD) == 0)
+ break;
+ }
+
+ if (i == E1000_FLASH_UPDATES) {
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_validate_nvm_checksum_82571 - Validate EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Calculates the EEPROM checksum by reading/adding each word of the EEPROM
+ * and then verifies that the sum of the EEPROM is equal to 0xBABA.
+ **/
+static s32 e1000e_validate_nvm_checksum_82571(struct e1000_hw *hw)
+{
+ if (hw->nvm.type == e1000_nvm_flash_hw)
+ e1000e_fix_nvm_checksum_82571(hw);
+
+ return e1000e_validate_nvm_checksum_generic(hw);
+}
+
+/**
+ * e1000e_write_nvm_eewr_82571 - Write to EEPROM for 82573 silicon
+ * @hw: pointer to the HW structure
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: 16 bit word(s) to be written to the EEPROM
+ *
+ * After checking for invalid values, poll the EEPROM to ensure the previous
+ * command has completed before trying to write the next word. After write
+ * poll for completion.
+ *
+ * If e1000e_update_nvm_checksum is not called after this function, the
+ * EEPROM will most likely contain an invalid checksum.
+ **/
+static s32 e1000e_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 i, eewr = 0;
+ s32 ret_val = 0;
+
+ /*
+ * A check for invalid values: offset too large, too many words,
+ * and not enough words.
+ */
+ if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) ||
+ (words == 0)) {
+ e_dbg("nvm parameter(s) out of bounds\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+ for (i = 0; i < words; i++) {
+ eewr = (data[i] << E1000_NVM_RW_REG_DATA) |
+ ((offset+i) << E1000_NVM_RW_ADDR_SHIFT) |
+ E1000_NVM_RW_REG_START;
+
+ ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE);
+ if (ret_val)
+ break;
+
+ ew32(EEWR, eewr);
+
+ ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE);
+ if (ret_val)
+ break;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_get_cfg_done_82571 - Poll for configuration done
+ * @hw: pointer to the HW structure
+ *
+ * Reads the management control register for the config done bit to be set.
+ **/
+static s32 e1000e_get_cfg_done_82571(struct e1000_hw *hw)
+{
+ s32 timeout = PHY_CFG_TIMEOUT;
+ s32 ret_val = E1000_SUCCESS;
+
+ while (timeout) {
+ if (er32(EEMNGCTL) & E1000_NVM_CFG_DONE_PORT_0)
+ break;
+ msleep(1);
+ timeout--;
+ }
+ if (!timeout) {
+ e_dbg("MNG configuration cycle has not completed.\n");
+ ret_val = -E1000_ERR_RESET;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_set_d0_lplu_state_82571 - Set Low Power Linkup D0 state
+ * @hw: pointer to the HW structure
+ * @active: true to enable LPLU, false to disable
+ *
+ * Sets the LPLU D0 state according to the active flag. When activating LPLU
+ * this function also disables smart speed and vice versa. LPLU will not be
+ * activated unless the device autonegotiation advertisement meets standards
+ * of either 10 or 10/100 or 10/100/1000 at all duplexes. This is a function
+ * pointer entry point only called by PHY setup routines.
+ **/
+static s32 e1000e_set_d0_lplu_state_82571(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+ u16 data;
+
+ if (!(phy->ops.read_reg))
+ goto out;
+
+ ret_val = e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &data);
+ if (ret_val)
+ goto out;
+
+ if (active) {
+ data |= IGP02E1000_PM_D0_LPLU;
+ ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT,
+ data);
+ if (ret_val)
+ goto out;
+
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ goto out;
+ } else {
+ data &= ~IGP02E1000_PM_D0_LPLU;
+ ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT,
+ data);
+ /*
+ * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1e_rphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ goto out;
+ } else if (phy->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1e_rphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ goto out;
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_reset_hw_82571 - Reset hardware
+ * @hw: pointer to the HW structure
+ *
+ * This resets the hardware into a known state.
+ **/
+static s32 e1000e_reset_hw_82571(struct e1000_hw *hw)
+{
+ u32 ctrl, extcnf_ctrl, ctrl_ext, icr;
+ s32 ret_val;
+ u16 i = 0;
+
+ /*
+ * Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ ret_val = e1000e_disable_pcie_master(hw);
+ if (ret_val)
+ e_dbg("PCI-E Master disable polling has failed.\n");
+
+ e_dbg("Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ ew32(RCTL, 0);
+ ew32(TCTL, E1000_TCTL_PSP);
+ e1e_flush();
+
+ msleep(10);
+
+ /*
+ * Must acquire the MDIO ownership before MAC reset.
+ * Ownership defaults to firmware after a reset.
+ */
+ switch (hw->mac.type) {
+ case e1000_82574:
+ case e1000_82583:
+ case e1000_82573:
+ extcnf_ctrl = er32(EXTCNF_CTRL);
+ extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
+
+ do {
+ ew32(EXTCNF_CTRL, extcnf_ctrl);
+ extcnf_ctrl = er32(EXTCNF_CTRL);
+
+ if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
+ break;
+
+ extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
+
+ msleep(2);
+ i++;
+ } while (i < MDIO_OWNERSHIP_TIMEOUT);
+ break;
+ default:
+ break;
+ }
+
+ ctrl = er32(CTRL);
+
+ e_dbg("Issuing a global reset to MAC\n");
+ ew32(CTRL, ctrl | E1000_CTRL_RST);
+
+ if (hw->nvm.type == e1000_nvm_flash_hw) {
+ udelay(10);
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+ ew32(CTRL_EXT, ctrl_ext);
+ e1e_flush();
+ }
+
+ ret_val = e1000e_get_auto_rd_done(hw);
+ if (ret_val)
+ /* We don't want to continue accessing MAC registers. */
+ goto out;
+
+ /*
+ * Phy configuration from NVM just starts after EECD_AUTO_RD is set.
+ * Need to wait for Phy configuration completion before accessing
+ * NVM and Phy.
+ */
+
+ switch (hw->mac.type) {
+ case e1000_82574:
+ case e1000_82583:
+ case e1000_82573:
+ msleep(25);
+ break;
+ default:
+ break;
+ }
+
+ /* Clear any pending interrupt events. */
+ ew32(IMC, 0xffffffff);
+ icr = er32(ICR);
+
+ /* Install any alternate MAC address into RAR0 */
+ ret_val = e1000e_check_alt_mac_addr_generic(hw);
+ if (ret_val)
+ goto out;
+
+ e1000e_set_laa_state_82571(hw, true);
+
+ /* Reinitialize the 82571 serdes link state machine */
+ if (hw->phy.media_type == e1000_media_type_internal_serdes)
+ hw->mac.serdes_link_state = e1000_serdes_link_down;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_init_hw_82571 - Initialize hardware
+ * @hw: pointer to the HW structure
+ *
+ * This inits the hardware readying it for operation.
+ **/
+static s32 e1000e_init_hw_82571(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 reg_data;
+ s32 ret_val;
+ u16 i, rar_count = mac->rar_entry_count;
+
+ e1000e_initialize_hw_bits_82571(hw);
+
+ /* Initialize identification LED */
+ ret_val = mac->ops.id_led_init(hw);
+ if (ret_val) {
+ e_dbg("Error initializing identification LED\n");
+ /* This is not fatal and we should not stop init due to this */
+ }
+
+ /* Disabling VLAN filtering */
+ e_dbg("Initializing the IEEE VLAN\n");
+ e1000e_clear_vfta(hw);
+
+ /* Setup the receive address. */
+ /*
+ * If, however, a locally administered address was assigned to the
+ * 82571, we must reserve a RAR for it to work around an issue where
+ * resetting one port will reload the MAC on the other port.
+ */
+ if (e1000e_get_laa_state_82571(hw))
+ rar_count--;
+ e1000e_init_rx_addrs(hw, rar_count);
+
+ /* Zero out the Multicast HASH table */
+ e_dbg("Zeroing the MTA\n");
+ for (i = 0; i < mac->mta_reg_count; i++)
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
+
+ /* Setup link and flow control */
+ ret_val = mac->ops.setup_link(hw);
+
+ /* Set the transmit descriptor write-back policy */
+ reg_data = er32(TXDCTL(0));
+ reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB |
+ E1000_TXDCTL_COUNT_DESC;
+ ew32(TXDCTL(0), reg_data);
+
+ /* ...for both queues. */
+ switch (mac->type) {
+ case e1000_82574:
+ case e1000_82583:
+ case e1000_82573:
+#if 0
+ e1000e_enable_tx_pkt_filtering(hw);
+#endif
+ reg_data = er32(GCR);
+ reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
+ ew32(GCR, reg_data);
+ break;
+ default:
+ reg_data = er32(TXDCTL(1));
+ reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB |
+ E1000_TXDCTL_COUNT_DESC;
+ ew32(TXDCTL(1), reg_data);
+ break;
+ }
+
+ /*
+ * Clear all of the statistics registers (clear on read). It is
+ * important that we do this after we have tried to establish link
+ * because the symbol error count will increment wildly if there
+ * is no link.
+ */
+ e1000e_clear_hw_cntrs_82571(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_initialize_hw_bits_82571 - Initialize hardware-dependent bits
+ * @hw: pointer to the HW structure
+ *
+ * Initializes required hardware-dependent bits needed for normal operation.
+ **/
+static void e1000e_initialize_hw_bits_82571(struct e1000_hw *hw)
+{
+ u32 reg;
+
+ /* Transmit Descriptor Control 0 */
+ reg = er32(TXDCTL(0));
+ reg |= (1 << 22);
+ ew32(TXDCTL(0), reg);
+
+ /* Transmit Descriptor Control 1 */
+ reg = er32(TXDCTL(1));
+ reg |= (1 << 22);
+ ew32(TXDCTL(1), reg);
+
+ /* Transmit Arbitration Control 0 */
+ reg = er32(TARC(0));
+ reg &= ~(0xF << 27); /* 30:27 */
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ reg |= (1 << 23) | (1 << 24) | (1 << 25) | (1 << 26);
+ break;
+ default:
+ break;
+ }
+ ew32(TARC(0), reg);
+
+ /* Transmit Arbitration Control 1 */
+ reg = er32(TARC(1));
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ reg &= ~((1 << 29) | (1 << 30));
+ reg |= (1 << 22) | (1 << 24) | (1 << 25) | (1 << 26);
+ if (er32(TCTL) & E1000_TCTL_MULR)
+ reg &= ~(1 << 28);
+ else
+ reg |= (1 << 28);
+ ew32(TARC(1), reg);
+ break;
+ default:
+ break;
+ }
+
+ /* Device Control */
+
+ switch (hw->mac.type) {
+ case e1000_82574:
+ case e1000_82583:
+ case e1000_82573:
+ reg = er32(CTRL);
+ reg &= ~(1 << 29);
+ ew32(CTRL, reg);
+ break;
+ default:
+ break;
+ }
+
+ /* Extended Device Control */
+ switch (hw->mac.type) {
+ case e1000_82574:
+ case e1000_82583:
+ case e1000_82573:
+ reg = er32(CTRL_EXT);
+ reg &= ~(1 << 23);
+ reg |= (1 << 22);
+ ew32(CTRL_EXT, reg);
+ break;
+ default:
+ break;
+ }
+
+
+ if (hw->mac.type == e1000_82571) {
+ reg = er32(PBA_ECC);
+ reg |= E1000_PBA_ECC_CORR_EN;
+ ew32(PBA_ECC, reg);
+ }
+
+ /*
+ * Workaround for hardware errata.
+ * Ensure that DMA Dynamic Clock gating is disabled on 82571 and 82572
+ */
+
+ if ((hw->mac.type == e1000_82571) ||
+ (hw->mac.type == e1000_82572)) {
+ reg = er32(CTRL_EXT);
+ reg &= ~E1000_CTRL_EXT_DMA_DYN_CLK_EN;
+ ew32(CTRL_EXT, reg);
+ }
+
+ /* PCI-Ex Control Registers */
+
+ switch (hw->mac.type) {
+ case e1000_82574:
+ case e1000_82583:
+ reg = er32(GCR);
+ reg |= (1 << 22);
+ ew32(GCR, reg);
+ /*
+ * Workaround for hardware errata.
+ * apply workaround for hardware errata documented in errata
+ * docs Fixes issue where some error prone or unreliable PCIe
+ * completions are occurring, particularly with ASPM enabled.
+ * Without fix, issue can cause tx timeouts.
+ */
+ reg = er32(GCR2);
+ reg |= 1;
+ ew32(GCR2, reg);
+ break;
+ default:
+ break;
+ }
+ return;
+}
+
+/**
+ * e1000e_clear_vfta_82571 - Clear VLAN filter table
+ * @hw: pointer to the HW structure
+ *
+ * Clears the register array which contains the VLAN filter table by
+ * setting all the values to 0.
+ **/
+static void e1000e_clear_vfta_82571(struct e1000_hw *hw)
+{
+ u32 offset;
+ u32 vfta_value = 0;
+ u32 vfta_offset = 0;
+ u32 vfta_bit_in_reg = 0;
+
+ switch (hw->mac.type) {
+ case e1000_82574:
+ case e1000_82583:
+ case e1000_82573:
+ if (hw->mng_cookie.vlan_id != 0) {
+ /*
+ *The VFTA is a 4096b bit-field, each identifying
+ *a single VLAN ID. The following operations
+ *determine which 32b entry (i.e. offset) into the
+ *array we want to set the VLAN ID (i.e. bit) of
+ *the manageability unit.
+ */
+ vfta_offset = (hw->mng_cookie.vlan_id >>
+ E1000_VFTA_ENTRY_SHIFT) & E1000_VFTA_ENTRY_MASK;
+ vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id &
+ E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
+ }
+
+ for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
+ /*
+ *If the offset we want to clear is the same offset of
+ *the manageability VLAN ID, then clear all bits except
+ *that of the manageability unit
+ */
+ vfta_value = (offset == vfta_offset) ?
+ vfta_bit_in_reg : 0;
+ E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset,
+ vfta_value);
+ e1e_flush();
+ }
+ break;
+ default:
+ break;
+ }
+}
+
+#if 0
+/**
+ * e1000e_check_mng_mode_82574 - Check manageability is enabled
+ * @hw: pointer to the HW structure
+ *
+ * Reads the NVM Initialization Control Word 2 and returns true
+ * (>0) if any manageability is enabled, else false (0).
+ **/
+static bool e1000e_check_mng_mode_82574(struct e1000_hw *hw)
+{
+ u16 data;
+
+ e1000e_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &data);
+ return (data & E1000_NVM_INIT_CTRL2_MNGM) != 0;
+}
+#endif
+
+/**
+ * e1000e_led_on_82574 - Turn LED on
+ * @hw: pointer to the HW structure
+ *
+ * Turn LED on.
+ **/
+static s32 e1000e_led_on_82574(struct e1000_hw *hw __unused)
+{
+#if 0
+ u32 ctrl;
+ u32 i;
+
+ ctrl = hw->mac.ledctl_mode2;
+ if (!(E1000_STATUS_LU & er32(STATUS))) {
+ /*
+ * If no link, then turn LED on by setting the invert bit
+ * for each LED that's "on" (0x0E) in ledctl_mode2.
+ */
+ for (i = 0; i < 4; i++)
+ if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
+ E1000_LEDCTL_MODE_LED_ON)
+ ctrl |= (E1000_LEDCTL_LED0_IVRT << (i * 8));
+ }
+ ew32(LEDCTL, ctrl);
+#endif
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_setup_link_82571 - Setup flow control and link settings
+ * @hw: pointer to the HW structure
+ *
+ * Determines which flow control settings to use, then configures flow
+ * control. Calls the appropriate media-specific link configuration
+ * function. Assuming the adapter has a valid link partner, a valid link
+ * should be established. Assumes the hardware has previously been reset
+ * and the transmitter and receiver are not enabled.
+ **/
+static s32 e1000e_setup_link_82571(struct e1000_hw *hw)
+{
+ /*
+ * 82573 does not have a word in the NVM to determine
+ * the default flow control setting, so we explicitly
+ * set it to full.
+ */
+ switch (hw->mac.type) {
+ case e1000_82574:
+ case e1000_82583:
+ case e1000_82573:
+ if (hw->fc.requested_mode == e1000_fc_default)
+ hw->fc.requested_mode = e1000_fc_full;
+ break;
+ default:
+ break;
+ }
+ return e1000e_setup_link(hw);
+}
+
+/**
+ * e1000e_setup_copper_link_82571 - Configure copper link settings
+ * @hw: pointer to the HW structure
+ *
+ * Configures the link for auto-neg or forced speed and duplex. Then we check
+ * for link, once link is established calls to configure collision distance
+ * and flow control are called.
+ **/
+static s32 e1000e_setup_copper_link_82571(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_SLU;
+ ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ew32(CTRL, ctrl);
+
+ switch (hw->phy.type) {
+ case e1000_phy_m88:
+ case e1000_phy_bm:
+ ret_val = e1000e_copper_link_setup_m88(hw);
+ break;
+ case e1000_phy_igp_2:
+ ret_val = e1000e_copper_link_setup_igp(hw);
+ break;
+ default:
+ ret_val = -E1000_ERR_PHY;
+ break;
+ }
+
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000e_setup_copper_link(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_setup_fiber_serdes_link_82571 - Setup link for fiber/serdes
+ * @hw: pointer to the HW structure
+ *
+ * Configures collision distance and flow control for fiber and serdes links.
+ * Upon successful setup, poll for link.
+ **/
+static s32 e1000e_setup_fiber_serdes_link_82571(struct e1000_hw *hw)
+{
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ /*
+ * If SerDes loopback mode is entered, there is no form
+ * of reset to take the adapter out of that mode. So we
+ * have to explicitly take the adapter out of loopback
+ * mode. This prevents drivers from twiddling their thumbs
+ * if another tool failed to take it out of loopback mode.
+ */
+ ew32(SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
+ break;
+ default:
+ break;
+ }
+
+ return e1000e_setup_fiber_serdes_link(hw);
+}
+
+/**
+ * e1000e_check_for_serdes_link_82571 - Check for link (Serdes)
+ * @hw: pointer to the HW structure
+ *
+ * Reports the link state as up or down.
+ *
+ * If autonegotiation is supported by the link partner, the link state is
+ * determined by the result of autongotiation. This is the most likely case.
+ * If autonegotiation is not supported by the link partner, and the link
+ * has a valid signal, force the link up.
+ *
+ * The link state is represented internally here by 4 states:
+ *
+ * 1) down
+ * 2) autoneg_progress
+ * 3) autoneg_complete (the link sucessfully autonegotiated)
+ * 4) forced_up (the link has been forced up, it did not autonegotiate)
+ *
+ **/
+s32 e1000e_check_for_serdes_link_82571(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 rxcw;
+ u32 ctrl;
+ u32 status;
+ s32 ret_val = E1000_SUCCESS;
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+ rxcw = er32(RXCW);
+
+ if ((rxcw & E1000_RXCW_SYNCH) && !(rxcw & E1000_RXCW_IV)) {
+
+ /* Receiver is synchronized with no invalid bits. */
+ switch (mac->serdes_link_state) {
+ case e1000_serdes_link_autoneg_complete:
+ if (!(status & E1000_STATUS_LU)) {
+ /*
+ * We have lost link, retry autoneg before
+ * reporting link failure
+ */
+ mac->serdes_link_state =
+ e1000_serdes_link_autoneg_progress;
+ mac->serdes_has_link = false;
+ e_dbg("AN_UP -> AN_PROG\n");
+ }
+ break;
+
+ case e1000_serdes_link_forced_up:
+ /*
+ * If we are receiving /C/ ordered sets, re-enable
+ * auto-negotiation in the TXCW register and disable
+ * forced link in the Device Control register in an
+ * attempt to auto-negotiate with our link partner.
+ */
+ if (rxcw & E1000_RXCW_C) {
+ /* Enable autoneg, and unforce link up */
+ ew32(TXCW, mac->txcw);
+ ew32(CTRL,
+ (ctrl & ~E1000_CTRL_SLU));
+ mac->serdes_link_state =
+ e1000_serdes_link_autoneg_progress;
+ mac->serdes_has_link = false;
+ e_dbg("FORCED_UP -> AN_PROG\n");
+ }
+ break;
+
+ case e1000_serdes_link_autoneg_progress:
+ if (rxcw & E1000_RXCW_C) {
+ /* We received /C/ ordered sets, meaning the
+ * link partner has autonegotiated, and we can
+ * trust the Link Up (LU) status bit
+ */
+ if (status & E1000_STATUS_LU) {
+ mac->serdes_link_state =
+ e1000_serdes_link_autoneg_complete;
+ e_dbg("AN_PROG -> AN_UP\n");
+ mac->serdes_has_link = true;
+ } else {
+ /* Autoneg completed, but failed */
+ mac->serdes_link_state =
+ e1000_serdes_link_down;
+ e_dbg("AN_PROG -> DOWN\n");
+ }
+ } else {
+ /* The link partner did not autoneg.
+ * Force link up and full duplex, and change
+ * state to forced.
+ */
+ ew32(TXCW,
+ (mac->txcw & ~E1000_TXCW_ANE));
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+ ew32(CTRL, ctrl);
+
+ /* Configure Flow Control after link up. */
+ ret_val =
+ e1000e_config_fc_after_link_up(hw);
+ if (ret_val) {
+ e_dbg("Error config flow control\n");
+ break;
+ }
+ mac->serdes_link_state =
+ e1000_serdes_link_forced_up;
+ mac->serdes_has_link = true;
+ e_dbg("AN_PROG -> FORCED_UP\n");
+ }
+ break;
+
+ case e1000_serdes_link_down:
+ default:
+ /* The link was down but the receiver has now gained
+ * valid sync, so lets see if we can bring the link
+ * up. */
+ ew32(TXCW, mac->txcw);
+ ew32(CTRL,
+ (ctrl & ~E1000_CTRL_SLU));
+ mac->serdes_link_state =
+ e1000_serdes_link_autoneg_progress;
+ e_dbg("DOWN -> AN_PROG\n");
+ break;
+ }
+ } else {
+ if (!(rxcw & E1000_RXCW_SYNCH)) {
+ mac->serdes_has_link = false;
+ mac->serdes_link_state = e1000_serdes_link_down;
+ e_dbg("ANYSTATE -> DOWN\n");
+ } else {
+ /*
+ * We have sync, and can tolerate one
+ * invalid (IV) codeword before declaring
+ * link down, so reread to look again
+ */
+ udelay(10);
+ rxcw = er32(RXCW);
+ if (rxcw & E1000_RXCW_IV) {
+ mac->serdes_link_state = e1000_serdes_link_down;
+ mac->serdes_has_link = false;
+ e_dbg("ANYSTATE -> DOWN\n");
+ }
+ }
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_valid_led_default_82571 - Verify a valid default LED config
+ * @hw: pointer to the HW structure
+ * @data: pointer to the NVM (EEPROM)
+ *
+ * Read the EEPROM for the current default LED configuration. If the
+ * LED configuration is not valid, set to a valid LED configuration.
+ **/
+static s32 e1000e_valid_led_default_82571(struct e1000_hw *hw, u16 *data)
+{
+ s32 ret_val;
+
+ ret_val = e1000e_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ goto out;
+ }
+
+ switch (hw->mac.type) {
+ case e1000_82574:
+ case e1000_82583:
+ case e1000_82573:
+ if(*data == ID_LED_RESERVED_F746)
+ *data = ID_LED_DEFAULT_82573;
+ break;
+ default:
+ if (*data == ID_LED_RESERVED_0000 ||
+ *data == ID_LED_RESERVED_FFFF)
+ *data = ID_LED_DEFAULT;
+ break;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_get_laa_state_82571 - Get locally administered address state
+ * @hw: pointer to the HW structure
+ *
+ * Retrieve and return the current locally administered address state.
+ **/
+bool e1000e_get_laa_state_82571(struct e1000_hw *hw)
+{
+ if (hw->mac.type != e1000_82571)
+ return false;
+
+ return hw->dev_spec._82571.laa_is_present;
+}
+
+/**
+ * e1000e_set_laa_state_82571 - Set locally administered address state
+ * @hw: pointer to the HW structure
+ * @state: enable/disable locally administered address
+ *
+ * Enable/Disable the current locally administered address state.
+ **/
+void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state)
+{
+ if (hw->mac.type != e1000_82571)
+ return;
+
+ hw->dev_spec._82571.laa_is_present = state;
+
+ /* If workaround is activated... */
+ if (state)
+ /*
+ * Hold a copy of the LAA in RAR[14] This is done so that
+ * between the time RAR[0] gets clobbered and the time it
+ * gets fixed, the actual LAA is in one of the RARs and no
+ * incoming packets directed to this port are dropped.
+ * Eventually the LAA will be in RAR[0] and RAR[14].
+ */
+ e1000e_rar_set(hw, hw->mac.addr,
+ hw->mac.rar_entry_count - 1);
+ return;
+}
+
+/**
+ * e1000e_fix_nvm_checksum_82571 - Fix EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Verifies that the EEPROM has completed the update. After updating the
+ * EEPROM, we need to check bit 15 in work 0x23 for the checksum fix. If
+ * the checksum fix is not implemented, we need to set the bit and update
+ * the checksum. Otherwise, if bit 15 is set and the checksum is incorrect,
+ * we need to return bad checksum.
+ **/
+static s32 e1000e_fix_nvm_checksum_82571(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ s32 ret_val = E1000_SUCCESS;
+ u16 data;
+
+ if (nvm->type != e1000_nvm_flash_hw)
+ goto out;
+
+ /*
+ * Check bit 4 of word 10h. If it is 0, firmware is done updating
+ * 10h-12h. Checksum may need to be fixed.
+ */
+ ret_val = e1000e_read_nvm(hw, 0x10, 1, &data);
+ if (ret_val)
+ goto out;
+
+ if (!(data & 0x10)) {
+ /*
+ * Read 0x23 and check bit 15. This bit is a 1
+ * when the checksum has already been fixed. If
+ * the checksum is still wrong and this bit is a
+ * 1, we need to return bad checksum. Otherwise,
+ * we need to set this bit to a 1 and update the
+ * checksum.
+ */
+ ret_val = e1000e_read_nvm(hw, 0x23, 1, &data);
+ if (ret_val)
+ goto out;
+
+ if (!(data & 0x8000)) {
+ data |= 0x8000;
+ ret_val = e1000e_write_nvm(hw, 0x23, 1, &data);
+ if (ret_val)
+ goto out;
+ ret_val = e1000e_update_nvm_checksum(hw);
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_mac_addr_82571 - Read device MAC address
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000e_read_mac_addr_82571(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ /*
+ * If there's an alternate MAC address place it in RAR0
+ * so that it will override the Si installed default perm
+ * address.
+ */
+ ret_val = e1000e_check_alt_mac_addr_generic(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000e_read_mac_addr_generic(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_power_down_phy_copper_82571 - Remove link during PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, remove the link.
+ **/
+static void e1000e_power_down_phy_copper_82571(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ struct e1000_mac_info *mac = &hw->mac;
+
+ if (!(phy->ops.check_reset_block))
+ return;
+
+ /* If the management interface is not enabled, then power down */
+ if (!(mac->ops.check_mng_mode(hw) || e1000e_check_reset_block(hw)))
+ e1000e_power_down_phy_copper(hw);
+
+ return;
+}
+
+/**
+ * e1000e_clear_hw_cntrs_82571 - Clear device specific hardware counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears the hardware counters by reading the counter registers.
+ **/
+static void e1000e_clear_hw_cntrs_82571(struct e1000_hw *hw __unused)
+{
+#if 0
+ e1000e_clear_hw_cntrs_base(hw);
+
+ er32(PRC64);
+ er32(PRC127);
+ er32(PRC255);
+ er32(PRC511);
+ er32(PRC1023);
+ er32(PRC1522);
+ er32(PTC64);
+ er32(PTC127);
+ er32(PTC255);
+ er32(PTC511);
+ er32(PTC1023);
+ er32(PTC1522);
+
+ er32(ALGNERRC);
+ er32(RXERRC);
+ er32(TNCRS);
+ er32(CEXTERR);
+ er32(TSCTC);
+ er32(TSCTFC);
+
+ er32(MGTPRC);
+ er32(MGTPDC);
+ er32(MGTPTC);
+
+ er32(IAC);
+ er32(ICRXOC);
+
+ er32(ICRXPTC);
+ er32(ICRXATC);
+ er32(ICTXPTC);
+ er32(ICTXATC);
+ er32(ICTXQEC);
+ er32(ICTXQMTC);
+ er32(ICRXDMTC);
+#endif
+}
+
+static struct pci_device_id e1000e_82571_nics[] = {
+ PCI_ROM(0x8086, 0x105E, "E1000_DEV_ID_82571EB_COPPER", "E1000_DEV_ID_82571EB_COPPER", board_82571),
+ PCI_ROM(0x8086, 0x105F, "E1000_DEV_ID_82571EB_FIBER", "E1000_DEV_ID_82571EB_FIBER", board_82571),
+ PCI_ROM(0x8086, 0x10A4, "E1000_DEV_ID_82571EB_QUAD_COPPER", "E1000_DEV_ID_82571EB_QUAD_COPPER", board_82571),
+ PCI_ROM(0x8086, 0x10BC, "E1000_DEV_ID_82571EB_QUAD_COPPER_LP", "E1000_DEV_ID_82571EB_QUAD_COPPER_LP", board_82571),
+ PCI_ROM(0x8086, 0x10A5, "E1000_DEV_ID_82571EB_QUAD_FIBER", "E1000_DEV_ID_82571EB_QUAD_FIBER", board_82571),
+ PCI_ROM(0x8086, 0x1060, "E1000_DEV_ID_82571EB_SERDES", "E1000_DEV_ID_82571EB_SERDES", board_82571),
+ PCI_ROM(0x8086, 0x10D9, "E1000_DEV_ID_82571EB_SERDES_DUAL", "E1000_DEV_ID_82571EB_SERDES_DUAL", board_82571),
+ PCI_ROM(0x8086, 0x10DA, "E1000_DEV_ID_82571EB_SERDES_QUAD", "E1000_DEV_ID_82571EB_SERDES_QUAD", board_82571),
+ PCI_ROM(0x8086, 0x10D5, "E1000_DEV_ID_82571PT_QUAD_COPPER", "E1000_DEV_ID_82571PT_QUAD_COPPER", board_82571),
+ PCI_ROM(0x8086, 0x10B9, "E1000_DEV_ID_82572EI", "E1000_DEV_ID_82572EI", board_82572),
+ PCI_ROM(0x8086, 0x107D, "E1000_DEV_ID_82572EI_COPPER", "E1000_DEV_ID_82572EI_COPPER", board_82572),
+ PCI_ROM(0x8086, 0x107E, "E1000_DEV_ID_82572EI_FIBER", "E1000_DEV_ID_82572EI_FIBER", board_82572),
+ PCI_ROM(0x8086, 0x107F, "E1000_DEV_ID_82572EI_SERDES", "E1000_DEV_ID_82572EI_SERDES", board_82572),
+ PCI_ROM(0x8086, 0x108B, "E1000_DEV_ID_82573E", "E1000_DEV_ID_82573E", board_82573),
+ PCI_ROM(0x8086, 0x108C, "E1000_DEV_ID_82573E_IAMT", "E1000_DEV_ID_82573E_IAMT", board_82573),
+ PCI_ROM(0x8086, 0x109A, "E1000_DEV_ID_82573L", "E1000_DEV_ID_82573L", board_82573),
+ PCI_ROM(0x8086, 0x10D3, "E1000_DEV_ID_82574L", "E1000_DEV_ID_82574L", board_82574),
+ PCI_ROM(0x8086, 0x10F6, "E1000_DEV_ID_82574LA", "E1000_DEV_ID_82574LA", board_82574),
+ PCI_ROM(0x8086, 0x150C, "E1000_DEV_ID_82583V", "E1000_DEV_ID_82583V", board_82583),
+};
+
+struct pci_driver e1000e_82571_driver __pci_driver = {
+ .ids = e1000e_82571_nics,
+ .id_count = (sizeof (e1000e_82571_nics) / sizeof (e1000e_82571_nics[0])),
+ .probe = e1000e_probe,
+ .remove = e1000e_remove,
+};
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#ifndef _E1000E_82571_H_
+#define _E1000E_82571_H_
+
+#define ID_LED_RESERVED_F746 0xF746
+#define ID_LED_DEFAULT_82573 ((ID_LED_DEF1_DEF2 << 12) | \
+ (ID_LED_OFF1_ON2 << 8) | \
+ (ID_LED_DEF1_DEF2 << 4) | \
+ (ID_LED_DEF1_DEF2))
+
+#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
+
+/* Intr Throttling - RW */
+#define E1000_EITR_82574(_n) (0x000E8 + (0x4 * (_n)))
+
+#define E1000_EIAC_82574 0x000DC /* Ext. Interrupt Auto Clear - RW */
+#define E1000_EIAC_MASK_82574 0x01F00000
+
+#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */
+
+#define E1000_RXCFGL 0x0B634 /* TimeSync Rx EtherType & Msg Type Reg - RW */
+
+bool e1000e_get_laa_state_82571(struct e1000_hw *hw);
+void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state);
+
+#endif
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#ifndef _E1000E_DEFINES_H_
+#define _E1000E_DEFINES_H_
+
+/* Number of Transmit and Receive Descriptors must be a multiple of 8 */
+#define REQ_TX_DESCRIPTOR_MULTIPLE 8
+#define REQ_RX_DESCRIPTOR_MULTIPLE 8
+
+/* Definitions for power management and wakeup registers */
+/* Wake Up Control */
+#define E1000_WUC_APME 0x00000001 /* APM Enable */
+#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
+#define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */
+#define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */
+#define E1000_WUC_LSCWE 0x00000010 /* Link Status wake up enable */
+#define E1000_WUC_LSCWO 0x00000020 /* Link Status wake up override */
+#define E1000_WUC_SPM 0x80000000 /* Enable SPM */
+#define E1000_WUC_PHY_WAKE 0x00000100 /* if PHY supports wakeup */
+
+/* Wake Up Filter Control */
+#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
+#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
+#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
+#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
+#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
+#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
+#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */
+#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */
+#define E1000_WUFC_IGNORE_TCO_PHY 0x00000800 /* Ignore WakeOn TCO packets */
+#define E1000_WUFC_FLX0_PHY 0x00001000 /* Flexible Filter 0 Enable */
+#define E1000_WUFC_FLX1_PHY 0x00002000 /* Flexible Filter 1 Enable */
+#define E1000_WUFC_FLX2_PHY 0x00004000 /* Flexible Filter 2 Enable */
+#define E1000_WUFC_FLX3_PHY 0x00008000 /* Flexible Filter 3 Enable */
+#define E1000_WUFC_FLX4_PHY 0x00000200 /* Flexible Filter 4 Enable */
+#define E1000_WUFC_FLX5_PHY 0x00000400 /* Flexible Filter 5 Enable */
+#define E1000_WUFC_IGNORE_TCO 0x00008000 /* Ignore WakeOn TCO packets */
+#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */
+#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */
+#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */
+#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */
+#define E1000_WUFC_FLX4 0x00100000 /* Flexible Filter 4 Enable */
+#define E1000_WUFC_FLX5 0x00200000 /* Flexible Filter 5 Enable */
+#define E1000_WUFC_ALL_FILTERS_PHY_4 0x0000F0FF /*Mask for all wakeup filters*/
+#define E1000_WUFC_FLX_OFFSET_PHY 12 /* Offset to the Flexible Filters bits */
+#define E1000_WUFC_FLX_FILTERS_PHY_4 0x0000F000 /*Mask for 4 flexible filters*/
+#define E1000_WUFC_ALL_FILTERS_PHY_6 0x0000F6FF /*Mask for 6 wakeup filters */
+#define E1000_WUFC_FLX_FILTERS_PHY_6 0x0000F600 /*Mask for 6 flexible filters*/
+#define E1000_WUFC_ALL_FILTERS 0x000F00FF /* Mask for all wakeup filters */
+#define E1000_WUFC_ALL_FILTERS_6 0x003F00FF /* Mask for all 6 wakeup filters*/
+#define E1000_WUFC_FLX_OFFSET 16 /* Offset to the Flexible Filters bits */
+#define E1000_WUFC_FLX_FILTERS 0x000F0000 /*Mask for the 4 flexible filters */
+#define E1000_WUFC_FLX_FILTERS_6 0x003F0000 /* Mask for 6 flexible filters */
+
+/* Wake Up Status */
+#define E1000_WUS_LNKC E1000_WUFC_LNKC
+#define E1000_WUS_MAG E1000_WUFC_MAG
+#define E1000_WUS_EX E1000_WUFC_EX
+#define E1000_WUS_MC E1000_WUFC_MC
+#define E1000_WUS_BC E1000_WUFC_BC
+#define E1000_WUS_ARP E1000_WUFC_ARP
+#define E1000_WUS_IPV4 E1000_WUFC_IPV4
+#define E1000_WUS_IPV6 E1000_WUFC_IPV6
+#define E1000_WUS_FLX0_PHY E1000_WUFC_FLX0_PHY
+#define E1000_WUS_FLX1_PHY E1000_WUFC_FLX1_PHY
+#define E1000_WUS_FLX2_PHY E1000_WUFC_FLX2_PHY
+#define E1000_WUS_FLX3_PHY E1000_WUFC_FLX3_PHY
+#define E1000_WUS_FLX_FILTERS_PHY_4 E1000_WUFC_FLX_FILTERS_PHY_4
+#define E1000_WUS_FLX0 E1000_WUFC_FLX0
+#define E1000_WUS_FLX1 E1000_WUFC_FLX1
+#define E1000_WUS_FLX2 E1000_WUFC_FLX2
+#define E1000_WUS_FLX3 E1000_WUFC_FLX3
+#define E1000_WUS_FLX4 E1000_WUFC_FLX4
+#define E1000_WUS_FLX5 E1000_WUFC_FLX5
+#define E1000_WUS_FLX4_PHY E1000_WUFC_FLX4_PHY
+#define E1000_WUS_FLX5_PHY E1000_WUFC_FLX5_PHY
+#define E1000_WUS_FLX_FILTERS E1000_WUFC_FLX_FILTERS
+#define E1000_WUS_FLX_FILTERS_6 E1000_WUFC_FLX_FILTERS_6
+#define E1000_WUS_FLX_FILTERS_PHY_6 E1000_WUFC_FLX_FILTERS_PHY_6
+
+/* Wake Up Packet Length */
+#define E1000_WUPL_LENGTH_MASK 0x0FFF /* Only the lower 12 bits are valid */
+
+/* Four Flexible Filters are supported */
+#define E1000_FLEXIBLE_FILTER_COUNT_MAX 4
+/* Six Flexible Filters are supported */
+#define E1000_FLEXIBLE_FILTER_COUNT_MAX_6 6
+
+/* Each Flexible Filter is at most 128 (0x80) bytes in length */
+#define E1000_FLEXIBLE_FILTER_SIZE_MAX 128
+
+#define E1000_FFLT_SIZE E1000_FLEXIBLE_FILTER_COUNT_MAX
+#define E1000_FFLT_SIZE_6 E1000_FLEXIBLE_FILTER_COUNT_MAX_6
+#define E1000_FFMT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX
+#define E1000_FFVT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX
+
+/* Extended Device Control */
+#define E1000_CTRL_EXT_GPI0_EN 0x00000001 /* Maps SDP4 to GPI0 */
+#define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */
+#define E1000_CTRL_EXT_PHYINT_EN E1000_CTRL_EXT_GPI1_EN
+#define E1000_CTRL_EXT_GPI2_EN 0x00000004 /* Maps SDP6 to GPI2 */
+#define E1000_CTRL_EXT_GPI3_EN 0x00000008 /* Maps SDP7 to GPI3 */
+/* Reserved (bits 4,5) in >= 82575 */
+#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Definable Pin 4 */
+#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Definable Pin 5 */
+#define E1000_CTRL_EXT_PHY_INT E1000_CTRL_EXT_SDP5_DATA
+#define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* Value of SW Definable Pin 6 */
+#define E1000_CTRL_EXT_SDP3_DATA 0x00000080 /* Value of SW Definable Pin 3 */
+/* SDP 4/5 (bits 8,9) are reserved in >= 82575 */
+#define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */
+#define E1000_CTRL_EXT_SDP5_DIR 0x00000200 /* Direction of SDP5 0=in 1=out */
+#define E1000_CTRL_EXT_SDP6_DIR 0x00000400 /* Direction of SDP6 0=in 1=out */
+#define E1000_CTRL_EXT_SDP3_DIR 0x00000800 /* Direction of SDP3 0=in 1=out */
+#define E1000_CTRL_EXT_ASDCHK 0x00001000 /* Initiate an ASD sequence */
+#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
+#define E1000_CTRL_EXT_IPS 0x00004000 /* Invert Power State */
+#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
+#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
+#define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clock Gating */
+#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000
+#define E1000_CTRL_EXT_LINK_MODE_TBI 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_KMRN 0x00000000
+#define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_PCIX_SERDES 0x00800000
+#define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000
+#define E1000_CTRL_EXT_EIAME 0x01000000
+#define E1000_CTRL_EXT_IRCA 0x00000001
+#define E1000_CTRL_EXT_WR_WMARK_MASK 0x03000000
+#define E1000_CTRL_EXT_WR_WMARK_256 0x00000000
+#define E1000_CTRL_EXT_WR_WMARK_320 0x01000000
+#define E1000_CTRL_EXT_WR_WMARK_384 0x02000000
+#define E1000_CTRL_EXT_WR_WMARK_448 0x03000000
+#define E1000_CTRL_EXT_CANC 0x04000000 /* Int delay cancellation */
+#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */
+/* IAME enable bit (27) was removed in >= 82575 */
+#define E1000_CTRL_EXT_IAME 0x08000000 /* Int acknowledge Auto-mask */
+#define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error
+ * detection enabled */
+#define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity
+ * error detection enable */
+#define E1000_CTRL_EXT_GHOST_PAREN 0x40000000
+#define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
+#define E1000_CTRL_EXT_LSECCK 0x00001000
+#define E1000_CTRL_EXT_PHYPDEN 0x00100000
+#define E1000_I2CCMD_REG_ADDR_SHIFT 16
+#define E1000_I2CCMD_REG_ADDR 0x00FF0000
+#define E1000_I2CCMD_PHY_ADDR_SHIFT 24
+#define E1000_I2CCMD_PHY_ADDR 0x07000000
+#define E1000_I2CCMD_OPCODE_READ 0x08000000
+#define E1000_I2CCMD_OPCODE_WRITE 0x00000000
+#define E1000_I2CCMD_RESET 0x10000000
+#define E1000_I2CCMD_READY 0x20000000
+#define E1000_I2CCMD_INTERRUPT_ENA 0x40000000
+#define E1000_I2CCMD_ERROR 0x80000000
+#define E1000_MAX_SGMII_PHY_REG_ADDR 255
+#define E1000_I2CCMD_PHY_TIMEOUT 200
+
+/* Receive Descriptor bit definitions */
+#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
+#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
+#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
+#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
+#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
+#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
+#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */
+#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */
+#define E1000_RXD_STAT_CRCV 0x100 /* Speculative CRC Valid */
+#define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */
+#define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */
+#define E1000_RXD_STAT_DYNINT 0x800 /* Pkt caused INT via DYNINT */
+#define E1000_RXD_STAT_ACK 0x8000 /* ACK Packet indication */
+#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
+#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
+#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
+#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */
+#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */
+#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */
+#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
+#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
+#define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */
+#define E1000_RXD_SPC_PRI_SHIFT 13
+#define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */
+#define E1000_RXD_SPC_CFI_SHIFT 12
+
+#define E1000_RXDEXT_STATERR_CE 0x01000000
+#define E1000_RXDEXT_STATERR_SE 0x02000000
+#define E1000_RXDEXT_STATERR_SEQ 0x04000000
+#define E1000_RXDEXT_STATERR_CXE 0x10000000
+#define E1000_RXDEXT_STATERR_TCPE 0x20000000
+#define E1000_RXDEXT_STATERR_IPE 0x40000000
+#define E1000_RXDEXT_STATERR_RXE 0x80000000
+
+#define E1000_RXDEXT_LSECH 0x01000000
+#define E1000_RXDEXT_LSECE_MASK 0x60000000
+#define E1000_RXDEXT_LSECE_NO_ERROR 0x00000000
+#define E1000_RXDEXT_LSECE_NO_SA_MATCH 0x20000000
+#define E1000_RXDEXT_LSECE_REPLAY_DETECT 0x40000000
+#define E1000_RXDEXT_LSECE_BAD_SIG 0x60000000
+
+/* mask to determine if packets should be dropped due to frame errors */
+#define E1000_RXD_ERR_FRAME_ERR_MASK ( \
+ E1000_RXD_ERR_CE | \
+ E1000_RXD_ERR_SE | \
+ E1000_RXD_ERR_SEQ | \
+ E1000_RXD_ERR_CXE | \
+ E1000_RXD_ERR_RXE)
+
+/* Same mask, but for extended and packet split descriptors */
+#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
+ E1000_RXDEXT_STATERR_CE | \
+ E1000_RXDEXT_STATERR_SE | \
+ E1000_RXDEXT_STATERR_SEQ | \
+ E1000_RXDEXT_STATERR_CXE | \
+ E1000_RXDEXT_STATERR_RXE)
+
+#define E1000_MRQC_ENABLE_MASK 0x00000007
+#define E1000_MRQC_ENABLE_RSS_2Q 0x00000001
+#define E1000_MRQC_ENABLE_RSS_INT 0x00000004
+#define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000
+#define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000
+#define E1000_MRQC_RSS_FIELD_IPV4 0x00020000
+#define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000
+#define E1000_MRQC_RSS_FIELD_IPV6_EX 0x00080000
+#define E1000_MRQC_RSS_FIELD_IPV6 0x00100000
+#define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000
+
+#define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000
+#define E1000_RXDPS_HDRSTAT_HDRLEN_MASK 0x000003FF
+
+/* Management Control */
+#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
+#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
+#define E1000_MANC_R_ON_FORCE 0x00000004 /* Reset on Force TCO - RO */
+#define E1000_MANC_RMCP_EN 0x00000100 /* Enable RCMP 026Fh Filtering */
+#define E1000_MANC_0298_EN 0x00000200 /* Enable RCMP 0298h Filtering */
+#define E1000_MANC_IPV4_EN 0x00000400 /* Enable IPv4 */
+#define E1000_MANC_IPV6_EN 0x00000800 /* Enable IPv6 */
+#define E1000_MANC_SNAP_EN 0x00001000 /* Accept LLC/SNAP */
+#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
+/* Enable Neighbor Discovery Filtering */
+#define E1000_MANC_NEIGHBOR_EN 0x00004000
+#define E1000_MANC_ARP_RES_EN 0x00008000 /* Enable ARP response Filtering */
+#define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */
+#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
+#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */
+#define E1000_MANC_RCV_ALL 0x00080000 /* Receive All Enabled */
+#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
+/* Enable MAC address filtering */
+#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000
+/* Enable MNG packets to host memory */
+#define E1000_MANC_EN_MNG2HOST 0x00200000
+/* Enable IP address filtering */
+#define E1000_MANC_EN_IP_ADDR_FILTER 0x00400000
+#define E1000_MANC_EN_XSUM_FILTER 0x00800000 /* Enable checksum filtering */
+#define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */
+#define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */
+#define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */
+#define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */
+#define E1000_MANC_SMB_DATA_IN 0x08000000 /* SMBus Data In */
+#define E1000_MANC_SMB_DATA_OUT 0x10000000 /* SMBus Data Out */
+#define E1000_MANC_SMB_CLK_OUT 0x20000000 /* SMBus Clock Out */
+
+#define E1000_MANC_SMB_DATA_OUT_SHIFT 28 /* SMBus Data Out Shift */
+#define E1000_MANC_SMB_CLK_OUT_SHIFT 29 /* SMBus Clock Out Shift */
+
+/* Receive Control */
+#define E1000_RCTL_RST 0x00000001 /* Software reset */
+#define E1000_RCTL_EN 0x00000002 /* enable */
+#define E1000_RCTL_SBP 0x00000004 /* store bad packet */
+#define E1000_RCTL_UPE 0x00000008 /* unicast promisc enable */
+#define E1000_RCTL_MPE 0x00000010 /* multicast promisc enable */
+#define E1000_RCTL_LPE 0x00000020 /* long packet enable */
+#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
+#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
+#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */
+#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
+#define E1000_RCTL_DTYP_MASK 0x00000C00 /* Descriptor type mask */
+#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */
+#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min thresh size */
+#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min thresh size */
+#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min thresh size */
+#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
+#define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */
+#define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */
+#define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */
+#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
+#define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */
+#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
+/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
+#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */
+#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */
+#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */
+#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */
+/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */
+#define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */
+#define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */
+#define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */
+#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
+#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
+#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
+#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */
+#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
+#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
+#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
+#define E1000_RCTL_FLXBUF_MASK 0x78000000 /* Flexible buffer size */
+#define E1000_RCTL_FLXBUF_SHIFT 27 /* Flexible buffer shift */
+
+/*
+ * Use byte values for the following shift parameters
+ * Usage:
+ * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
+ * E1000_PSRCTL_BSIZE0_MASK) |
+ * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
+ * E1000_PSRCTL_BSIZE1_MASK) |
+ * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
+ * E1000_PSRCTL_BSIZE2_MASK) |
+ * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
+ * E1000_PSRCTL_BSIZE3_MASK))
+ * where value0 = [128..16256], default=256
+ * value1 = [1024..64512], default=4096
+ * value2 = [0..64512], default=4096
+ * value3 = [0..64512], default=0
+ */
+
+#define E1000_PSRCTL_BSIZE0_MASK 0x0000007F
+#define E1000_PSRCTL_BSIZE1_MASK 0x00003F00
+#define E1000_PSRCTL_BSIZE2_MASK 0x003F0000
+#define E1000_PSRCTL_BSIZE3_MASK 0x3F000000
+
+#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
+#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
+#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
+#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
+
+/* SWFW_SYNC Definitions */
+#define E1000_SWFW_EEP_SM 0x01
+#define E1000_SWFW_PHY0_SM 0x02
+#define E1000_SWFW_PHY1_SM 0x04
+#define E1000_SWFW_CSR_SM 0x08
+
+/* FACTPS Definitions */
+#define E1000_FACTPS_LFS 0x40000000 /* LAN Function Select */
+/* Device Control */
+#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
+#define E1000_CTRL_BEM 0x00000002 /* Endian Mode.0=little,1=big */
+#define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */
+#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master reqs */
+#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
+#define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */
+#define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */
+#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
+#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
+#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
+#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
+#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */
+#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
+#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
+#define E1000_CTRL_BEM32 0x00000400 /* Big Endian 32 mode */
+#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
+#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
+#define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */
+#define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock
+ * indication in SDP[0] */
+#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through
+ * PHYRST_N pin */
+#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external
+ * LINK_0 and LINK_1 pins */
+#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
+#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
+#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */
+#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */
+#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
+#define E1000_CTRL_SWDPIO1 0x00800000 /* SWDPIN 1 input or output */
+#define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */
+#define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */
+#define E1000_CTRL_RST 0x04000000 /* Global reset */
+#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
+#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
+#define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */
+#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
+#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
+#define E1000_CTRL_SW2FW_INT 0x02000000 /* Initiate an interrupt to ME */
+#define E1000_CTRL_I2C_ENA 0x02000000 /* I2C enable */
+
+/*
+ * Bit definitions for the Management Data IO (MDIO) and Management Data
+ * Clock (MDC) pins in the Device Control Register.
+ */
+#define E1000_CTRL_PHY_RESET_DIR E1000_CTRL_SWDPIO0
+#define E1000_CTRL_PHY_RESET E1000_CTRL_SWDPIN0
+#define E1000_CTRL_MDIO_DIR E1000_CTRL_SWDPIO2
+#define E1000_CTRL_MDIO E1000_CTRL_SWDPIN2
+#define E1000_CTRL_MDC_DIR E1000_CTRL_SWDPIO3
+#define E1000_CTRL_MDC E1000_CTRL_SWDPIN3
+#define E1000_CTRL_PHY_RESET_DIR4 E1000_CTRL_EXT_SDP4_DIR
+#define E1000_CTRL_PHY_RESET4 E1000_CTRL_EXT_SDP4_DATA
+
+#define E1000_CONNSW_ENRGSRC 0x4
+#define E1000_PCS_CFG_PCS_EN 8
+#define E1000_PCS_LCTL_FLV_LINK_UP 1
+#define E1000_PCS_LCTL_FSV_10 0
+#define E1000_PCS_LCTL_FSV_100 2
+#define E1000_PCS_LCTL_FSV_1000 4
+#define E1000_PCS_LCTL_FDV_FULL 8
+#define E1000_PCS_LCTL_FSD 0x10
+#define E1000_PCS_LCTL_FORCE_LINK 0x20
+#define E1000_PCS_LCTL_LOW_LINK_LATCH 0x40
+#define E1000_PCS_LCTL_FORCE_FCTRL 0x80
+#define E1000_PCS_LCTL_AN_ENABLE 0x10000
+#define E1000_PCS_LCTL_AN_RESTART 0x20000
+#define E1000_PCS_LCTL_AN_TIMEOUT 0x40000
+#define E1000_PCS_LCTL_AN_SGMII_BYPASS 0x80000
+#define E1000_PCS_LCTL_AN_SGMII_TRIGGER 0x100000
+#define E1000_PCS_LCTL_FAST_LINK_TIMER 0x1000000
+#define E1000_PCS_LCTL_LINK_OK_FIX 0x2000000
+#define E1000_PCS_LCTL_CRS_ON_NI 0x4000000
+#define E1000_ENABLE_SERDES_LOOPBACK 0x0410
+
+#define E1000_PCS_LSTS_LINK_OK 1
+#define E1000_PCS_LSTS_SPEED_10 0
+#define E1000_PCS_LSTS_SPEED_100 2
+#define E1000_PCS_LSTS_SPEED_1000 4
+#define E1000_PCS_LSTS_DUPLEX_FULL 8
+#define E1000_PCS_LSTS_SYNK_OK 0x10
+#define E1000_PCS_LSTS_AN_COMPLETE 0x10000
+#define E1000_PCS_LSTS_AN_PAGE_RX 0x20000
+#define E1000_PCS_LSTS_AN_TIMED_OUT 0x40000
+#define E1000_PCS_LSTS_AN_REMOTE_FAULT 0x80000
+#define E1000_PCS_LSTS_AN_ERROR_RWS 0x100000
+
+/* Device Status */
+#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
+#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
+#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
+#define E1000_STATUS_FUNC_SHIFT 2
+#define E1000_STATUS_FUNC_0 0x00000000 /* Function 0 */
+#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
+#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
+#define E1000_STATUS_TBIMODE 0x00000020 /* TBI mode */
+#define E1000_STATUS_SPEED_MASK 0x000000C0
+#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */
+#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
+#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
+#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */
+#define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */
+#define E1000_STATUS_PHYRA 0x00000400 /* PHY Reset Asserted */
+#define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state.
+ * Clear on write '0'. */
+#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Master request status */
+#define E1000_STATUS_MTXCKOK 0x00000400 /* MTX clock running OK */
+#define E1000_STATUS_PCI66 0x00000800 /* In 66Mhz slot */
+#define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */
+#define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */
+#define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */
+#define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */
+#define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */
+#define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */
+#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */
+#define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution
+ * disabled */
+#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */
+#define E1000_STATUS_FUSE_8 0x04000000
+#define E1000_STATUS_FUSE_9 0x08000000
+#define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */
+#define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */
+
+/* Constants used to interpret the masked PCI-X bus speed. */
+#define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */
+#define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed 66-100 MHz */
+#define E1000_STATUS_PCIX_SPEED_133 0x00008000 /*PCI-X bus speed 100-133 MHz*/
+
+#define SPEED_10 10
+#define SPEED_100 100
+#define SPEED_1000 1000
+#define HALF_DUPLEX 1
+#define FULL_DUPLEX 2
+
+#define PHY_FORCE_TIME 20
+
+#define ADVERTISE_10_HALF 0x0001
+#define ADVERTISE_10_FULL 0x0002
+#define ADVERTISE_100_HALF 0x0004
+#define ADVERTISE_100_FULL 0x0008
+#define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */
+#define ADVERTISE_1000_FULL 0x0020
+
+/* 1000/H is not supported, nor spec-compliant. */
+#define E1000_ALL_SPEED_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
+ ADVERTISE_100_HALF | ADVERTISE_100_FULL | \
+ ADVERTISE_1000_FULL)
+#define E1000_ALL_NOT_GIG (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
+ ADVERTISE_100_HALF | ADVERTISE_100_FULL)
+#define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL)
+#define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL)
+#define E1000_ALL_FULL_DUPLEX (ADVERTISE_10_FULL | ADVERTISE_100_FULL | \
+ ADVERTISE_1000_FULL)
+#define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF)
+
+#define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX
+
+/* LED Control */
+#define E1000_PHY_LED0_MODE_MASK 0x00000007
+#define E1000_PHY_LED0_IVRT 0x00000008
+#define E1000_PHY_LED0_BLINK 0x00000010
+#define E1000_PHY_LED0_MASK 0x0000001F
+
+#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
+#define E1000_LEDCTL_LED0_MODE_SHIFT 0
+#define E1000_LEDCTL_LED0_BLINK_RATE 0x00000020
+#define E1000_LEDCTL_LED0_IVRT 0x00000040
+#define E1000_LEDCTL_LED0_BLINK 0x00000080
+#define E1000_LEDCTL_LED1_MODE_MASK 0x00000F00
+#define E1000_LEDCTL_LED1_MODE_SHIFT 8
+#define E1000_LEDCTL_LED1_BLINK_RATE 0x00002000
+#define E1000_LEDCTL_LED1_IVRT 0x00004000
+#define E1000_LEDCTL_LED1_BLINK 0x00008000
+#define E1000_LEDCTL_LED2_MODE_MASK 0x000F0000
+#define E1000_LEDCTL_LED2_MODE_SHIFT 16
+#define E1000_LEDCTL_LED2_BLINK_RATE 0x00200000
+#define E1000_LEDCTL_LED2_IVRT 0x00400000
+#define E1000_LEDCTL_LED2_BLINK 0x00800000
+#define E1000_LEDCTL_LED3_MODE_MASK 0x0F000000
+#define E1000_LEDCTL_LED3_MODE_SHIFT 24
+#define E1000_LEDCTL_LED3_BLINK_RATE 0x20000000
+#define E1000_LEDCTL_LED3_IVRT 0x40000000
+#define E1000_LEDCTL_LED3_BLINK 0x80000000
+
+#define E1000_LEDCTL_MODE_LINK_10_1000 0x0
+#define E1000_LEDCTL_MODE_LINK_100_1000 0x1
+#define E1000_LEDCTL_MODE_LINK_UP 0x2
+#define E1000_LEDCTL_MODE_ACTIVITY 0x3
+#define E1000_LEDCTL_MODE_LINK_ACTIVITY 0x4
+#define E1000_LEDCTL_MODE_LINK_10 0x5
+#define E1000_LEDCTL_MODE_LINK_100 0x6
+#define E1000_LEDCTL_MODE_LINK_1000 0x7
+#define E1000_LEDCTL_MODE_PCIX_MODE 0x8
+#define E1000_LEDCTL_MODE_FULL_DUPLEX 0x9
+#define E1000_LEDCTL_MODE_COLLISION 0xA
+#define E1000_LEDCTL_MODE_BUS_SPEED 0xB
+#define E1000_LEDCTL_MODE_BUS_SIZE 0xC
+#define E1000_LEDCTL_MODE_PAUSED 0xD
+#define E1000_LEDCTL_MODE_LED_ON 0xE
+#define E1000_LEDCTL_MODE_LED_OFF 0xF
+
+/* Transmit Descriptor bit definitions */
+#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */
+#define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */
+#define E1000_TXD_POPTS_SHIFT 8 /* POPTS shift */
+#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
+#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
+#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
+#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
+#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
+#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
+#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
+#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
+#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
+#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
+#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
+#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
+#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
+#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
+#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
+#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
+#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
+#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
+/* Extended desc bits for Linksec and timesync */
+#define E1000_TXD_CMD_LINKSEC 0x10000000 /* Apply LinkSec on packet */
+#define E1000_TXD_EXTCMD_TSTAMP 0x00000010 /* IEEE1588 Timestamp packet */
+
+/* Transmit Control */
+#define E1000_TCTL_RST 0x00000001 /* software reset */
+#define E1000_TCTL_EN 0x00000002 /* enable tx */
+#define E1000_TCTL_BCE 0x00000004 /* busy check enable */
+#define E1000_TCTL_PSP 0x00000008 /* pad short packets */
+#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
+#define E1000_TCTL_COLD 0x003ff000 /* collision distance */
+#define E1000_TCTL_SWXOFF 0x00400000 /* SW Xoff transmission */
+#define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */
+#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
+#define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */
+#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */
+
+/* Transmit Arbitration Count */
+#define E1000_TARC0_ENABLE 0x00000400 /* Enable Tx Queue 0 */
+
+/* SerDes Control */
+#define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
+
+/* Receive Checksum Control */
+#define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */
+#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */
+#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
+#define E1000_RXCSUM_IPV6OFL 0x00000400 /* IPv6 checksum offload */
+#define E1000_RXCSUM_CRCOFL 0x00000800 /* CRC32 offload enable */
+#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */
+#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
+
+/* Header split receive */
+#define E1000_RFCTL_ISCSI_DIS 0x00000001
+#define E1000_RFCTL_ISCSI_DWC_MASK 0x0000003E
+#define E1000_RFCTL_ISCSI_DWC_SHIFT 1
+#define E1000_RFCTL_NFSW_DIS 0x00000040
+#define E1000_RFCTL_NFSR_DIS 0x00000080
+#define E1000_RFCTL_NFS_VER_MASK 0x00000300
+#define E1000_RFCTL_NFS_VER_SHIFT 8
+#define E1000_RFCTL_IPV6_DIS 0x00000400
+#define E1000_RFCTL_IPV6_XSUM_DIS 0x00000800
+#define E1000_RFCTL_ACK_DIS 0x00001000
+#define E1000_RFCTL_ACKD_DIS 0x00002000
+#define E1000_RFCTL_IPFRSP_DIS 0x00004000
+#define E1000_RFCTL_EXTEN 0x00008000
+#define E1000_RFCTL_IPV6_EX_DIS 0x00010000
+#define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000
+#define E1000_RFCTL_LEF 0x00040000
+
+/* Collision related configuration parameters */
+#define E1000_COLLISION_THRESHOLD 15
+#define E1000_CT_SHIFT 4
+#define E1000_COLLISION_DISTANCE 63
+#define E1000_COLD_SHIFT 12
+
+/* Default values for the transmit IPG register */
+#define DEFAULT_82543_TIPG_IPGT_FIBER 9
+#define DEFAULT_82543_TIPG_IPGT_COPPER 8
+
+#define E1000_TIPG_IPGT_MASK 0x000003FF
+#define E1000_TIPG_IPGR1_MASK 0x000FFC00
+#define E1000_TIPG_IPGR2_MASK 0x3FF00000
+
+#define DEFAULT_82543_TIPG_IPGR1 8
+#define E1000_TIPG_IPGR1_SHIFT 10
+
+#define DEFAULT_82543_TIPG_IPGR2 6
+#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7
+#define E1000_TIPG_IPGR2_SHIFT 20
+
+/* Ethertype field values */
+#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */
+
+#define ETHERNET_FCS_SIZE 4
+#define MAX_JUMBO_FRAME_SIZE 0x3F00
+
+/* Extended Configuration Control and Size */
+#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
+#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001
+#define E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE 0x00000008
+#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020
+#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK 0x00FF0000
+#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT 16
+#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK 0x0FFF0000
+#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT 16
+
+#define E1000_PHY_CTRL_SPD_EN 0x00000001
+#define E1000_PHY_CTRL_D0A_LPLU 0x00000002
+#define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004
+#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008
+#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040
+
+#define E1000_KABGTXD_BGSQLBIAS 0x00050000
+
+/* PBA constants */
+#define E1000_PBA_6K 0x0006 /* 6KB */
+#define E1000_PBA_8K 0x0008 /* 8KB */
+#define E1000_PBA_10K 0x000A /* 10KB */
+#define E1000_PBA_12K 0x000C /* 12KB */
+#define E1000_PBA_14K 0x000E /* 14KB */
+#define E1000_PBA_16K 0x0010 /* 16KB */
+#define E1000_PBA_18K 0x0012
+#define E1000_PBA_20K 0x0014
+#define E1000_PBA_22K 0x0016
+#define E1000_PBA_24K 0x0018
+#define E1000_PBA_26K 0x001A
+#define E1000_PBA_30K 0x001E
+#define E1000_PBA_32K 0x0020
+#define E1000_PBA_34K 0x0022
+#define E1000_PBA_35K 0x0023
+#define E1000_PBA_38K 0x0026
+#define E1000_PBA_40K 0x0028
+#define E1000_PBA_48K 0x0030 /* 48KB */
+#define E1000_PBA_64K 0x0040 /* 64KB */
+
+#define E1000_PBS_16K E1000_PBA_16K
+#define E1000_PBS_24K E1000_PBA_24K
+
+#define IFS_MAX 80
+#define IFS_MIN 40
+#define IFS_RATIO 4
+#define IFS_STEP 10
+#define MIN_NUM_XMITS 1000
+
+/* SW Semaphore Register */
+#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
+#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
+#define E1000_SWSM_WMNG 0x00000004 /* Wake MNG Clock */
+#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */
+
+#define E1000_SWSM2_LOCK 0x00000002 /* Secondary driver semaphore bit */
+
+/* Interrupt Cause Read */
+#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
+#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */
+#define E1000_ICR_LSC 0x00000004 /* Link Status Change */
+#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */
+#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
+#define E1000_ICR_RXO 0x00000040 /* rx overrun */
+#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
+#define E1000_ICR_VMMB 0x00000100 /* VM MB event */
+#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */
+#define E1000_ICR_RXCFG 0x00000400 /* Rx /c/ ordered set */
+#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */
+#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */
+#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */
+#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */
+#define E1000_ICR_TXD_LOW 0x00008000
+#define E1000_ICR_SRPD 0x00010000
+#define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */
+#define E1000_ICR_MNG 0x00040000 /* Manageability event */
+#define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */
+#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver
+ * should claim the interrupt */
+#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* Q0 Rx desc FIFO parity error */
+#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* Q0 Tx desc FIFO parity error */
+#define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity err */
+#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */
+#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* Q1 Rx desc FIFO parity error */
+#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* Q1 Tx desc FIFO parity error */
+#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */
+#define E1000_ICR_DSW 0x00000020 /* FW changed the status of DISSW
+ * bit in the FWSM */
+#define E1000_ICR_PHYINT 0x00001000 /* LAN connected device generates
+ * an interrupt */
+#define E1000_ICR_DOUTSYNC 0x10000000 /* NIC DMA out of sync */
+#define E1000_ICR_EPRST 0x00100000 /* ME hardware reset occurs */
+#define E1000_ICR_RXQ0 0x00100000 /* Rx Queue 0 Interrupt */
+#define E1000_ICR_RXQ1 0x00200000 /* Rx Queue 1 Interrupt */
+#define E1000_ICR_TXQ0 0x00400000 /* Tx Queue 0 Interrupt */
+#define E1000_ICR_TXQ1 0x00800000 /* Tx Queue 1 Interrupt */
+#define E1000_ICR_OTHER 0x01000000 /* Other Interrupts */
+
+/* PBA ECC Register */
+#define E1000_PBA_ECC_COUNTER_MASK 0xFFF00000 /* ECC counter mask */
+#define E1000_PBA_ECC_COUNTER_SHIFT 20 /* ECC counter shift value */
+#define E1000_PBA_ECC_CORR_EN 0x00000001 /* Enable ECC error correction */
+#define E1000_PBA_ECC_STAT_CLR 0x00000002 /* Clear ECC error counter */
+#define E1000_PBA_ECC_INT_EN 0x00000004 /* Enable ICR bit 5 on ECC error */
+
+/*
+ * This defines the bits that are set in the Interrupt Mask
+ * Set/Read Register. Each bit is documented below:
+ * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
+ * o RXSEQ = Receive Sequence Error
+ */
+#define POLL_IMS_ENABLE_MASK ( \
+ E1000_IMS_RXDMT0 | \
+ E1000_IMS_RXSEQ)
+
+/*
+ * This defines the bits that are set in the Interrupt Mask
+ * Set/Read Register. Each bit is documented below:
+ * o RXT0 = Receiver Timer Interrupt (ring 0)
+ * o TXDW = Transmit Descriptor Written Back
+ * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
+ * o RXSEQ = Receive Sequence Error
+ * o LSC = Link Status Change
+ */
+#define IMS_ENABLE_MASK ( \
+ E1000_IMS_RXT0 | \
+ E1000_IMS_TXDW | \
+ E1000_IMS_RXDMT0 | \
+ E1000_IMS_RXSEQ | \
+ E1000_IMS_LSC)
+
+/* Interrupt Mask Set */
+#define E1000_IMS_TXDW E1000_ICR_TXDW /* Tx desc written back */
+#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_IMS_VMMB E1000_ICR_VMMB /* Mail box activity */
+#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_IMS_RXCFG E1000_ICR_RXCFG /* Rx /c/ ordered set */
+#define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW
+#define E1000_IMS_SRPD E1000_ICR_SRPD
+#define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* Q0 Rx desc FIFO
+ * parity error */
+#define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* Q0 Tx desc FIFO
+ * parity error */
+#define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer
+ * parity error */
+#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity
+ * error */
+#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* Q1 Rx desc FIFO
+ * parity error */
+#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* Q1 Tx desc FIFO
+ * parity error */
+#define E1000_IMS_DSW E1000_ICR_DSW
+#define E1000_IMS_PHYINT E1000_ICR_PHYINT
+#define E1000_IMS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */
+#define E1000_IMS_EPRST E1000_ICR_EPRST
+#define E1000_IMS_RXQ0 E1000_ICR_RXQ0 /* Rx Queue 0 Interrupt */
+#define E1000_IMS_RXQ1 E1000_ICR_RXQ1 /* Rx Queue 1 Interrupt */
+#define E1000_IMS_TXQ0 E1000_ICR_TXQ0 /* Tx Queue 0 Interrupt */
+#define E1000_IMS_TXQ1 E1000_ICR_TXQ1 /* Tx Queue 1 Interrupt */
+#define E1000_IMS_OTHER E1000_ICR_OTHER /* Other Interrupts */
+
+/* Interrupt Cause Set */
+#define E1000_ICS_TXDW E1000_ICR_TXDW /* Tx desc written back */
+#define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_ICS_RXCFG E1000_ICR_RXCFG /* Rx /c/ ordered set */
+#define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_ICS_TXD_LOW E1000_ICR_TXD_LOW
+#define E1000_ICS_SRPD E1000_ICR_SRPD
+#define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* Q0 Rx desc FIFO
+ * parity error */
+#define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* Q0 Tx desc FIFO
+ * parity error */
+#define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer
+ * parity error */
+#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity
+ * error */
+#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* Q1 Rx desc FIFO
+ * parity error */
+#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* Q1 Tx desc FIFO
+ * parity error */
+#define E1000_ICS_DSW E1000_ICR_DSW
+#define E1000_ICS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */
+#define E1000_ICS_PHYINT E1000_ICR_PHYINT
+#define E1000_ICS_EPRST E1000_ICR_EPRST
+
+/* Transmit Descriptor Control */
+#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */
+#define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */
+#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */
+#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */
+#define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */
+#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
+#define E1000_TXDCTL_MAX_TX_DESC_PREFETCH 0x0100001F /* GRAN=1, PTHRESH=31 */
+/* Enable the counting of descriptors still to be processed. */
+#define E1000_TXDCTL_COUNT_DESC 0x00400000
+
+/* Flow Control Constants */
+#define FLOW_CONTROL_ADDRESS_LOW 0x00C28001
+#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
+#define FLOW_CONTROL_TYPE 0x8808
+
+/* 802.1q VLAN Packet Size */
+#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMA'd) */
+#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
+
+/* Receive Address */
+/*
+ * Number of high/low register pairs in the RAR. The RAR (Receive Address
+ * Registers) holds the directed and multicast addresses that we monitor.
+ * Technically, we have 16 spots. However, we reserve one of these spots
+ * (RAR[15]) for our directed address used by controllers with
+ * manageability enabled, allowing us room for 15 multicast addresses.
+ */
+#define E1000_RAR_ENTRIES 15
+#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
+#define E1000_RAL_MAC_ADDR_LEN 4
+#define E1000_RAH_MAC_ADDR_LEN 2
+#define E1000_RAH_POOL_MASK 0x03FC0000
+#define E1000_RAH_POOL_1 0x00040000
+
+/* Error Codes */
+#define E1000_SUCCESS 0
+#define E1000_ERR_NVM 1
+#define E1000_ERR_PHY 2
+#define E1000_ERR_CONFIG 3
+#define E1000_ERR_PARAM 4
+#define E1000_ERR_MAC_INIT 5
+#define E1000_ERR_PHY_TYPE 6
+#define E1000_ERR_RESET 9
+#define E1000_ERR_MASTER_REQUESTS_PENDING 10
+#define E1000_ERR_HOST_INTERFACE_COMMAND 11
+#define E1000_BLK_PHY_RESET 12
+#define E1000_ERR_SWFW_SYNC 13
+#define E1000_NOT_IMPLEMENTED 14
+#define E1000_ERR_MBX 15
+
+/* Loop limit on how long we wait for auto-negotiation to complete */
+#define FIBER_LINK_UP_LIMIT 50
+#define COPPER_LINK_UP_LIMIT 10
+#define PHY_AUTO_NEG_LIMIT 45
+#define PHY_FORCE_LIMIT 20
+/* Number of 100 microseconds we wait for PCI Express master disable */
+#define MASTER_DISABLE_TIMEOUT 800
+/* Number of milliseconds we wait for PHY configuration done after MAC reset */
+#define PHY_CFG_TIMEOUT 100
+/* Number of 2 milliseconds we wait for acquiring MDIO ownership. */
+#define MDIO_OWNERSHIP_TIMEOUT 10
+/* Number of milliseconds for NVM auto read done after MAC reset. */
+#define AUTO_READ_DONE_TIMEOUT 10
+
+/* Flow Control */
+#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */
+#define E1000_FCRTH_XFCE 0x80000000 /* External Flow Control Enable */
+#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */
+#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
+
+/* Transmit Configuration Word */
+#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */
+#define E1000_TXCW_HD 0x00000040 /* TXCW half duplex */
+#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */
+#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */
+#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */
+#define E1000_TXCW_RF 0x00003000 /* TXCW remote fault */
+#define E1000_TXCW_NP 0x00008000 /* TXCW next page */
+#define E1000_TXCW_CW 0x0000ffff /* TxConfigWord mask */
+#define E1000_TXCW_TXC 0x40000000 /* Transmit Config control */
+#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */
+
+/* Receive Configuration Word */
+#define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */
+#define E1000_RXCW_NC 0x04000000 /* Receive config no carrier */
+#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */
+#define E1000_RXCW_CC 0x10000000 /* Receive config change */
+#define E1000_RXCW_C 0x20000000 /* Receive config */
+#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */
+#define E1000_RXCW_ANC 0x80000000 /* Auto-neg complete */
+
+
+/* PCI Express Control */
+#define E1000_GCR_RXD_NO_SNOOP 0x00000001
+#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002
+#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004
+#define E1000_GCR_TXD_NO_SNOOP 0x00000008
+#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010
+#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020
+#define E1000_GCR_CMPL_TMOUT_MASK 0x0000F000
+#define E1000_GCR_CMPL_TMOUT_10ms 0x00001000
+#define E1000_GCR_CMPL_TMOUT_RESEND 0x00010000
+#define E1000_GCR_CAP_VER2 0x00040000
+
+#define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \
+ E1000_GCR_RXDSCW_NO_SNOOP | \
+ E1000_GCR_RXDSCR_NO_SNOOP | \
+ E1000_GCR_TXD_NO_SNOOP | \
+ E1000_GCR_TXDSCW_NO_SNOOP | \
+ E1000_GCR_TXDSCR_NO_SNOOP)
+
+/* PHY Control Register */
+#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */
+#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */
+#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
+#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
+#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */
+#define MII_CR_POWER_DOWN 0x0800 /* Power down */
+#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
+#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */
+#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
+#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
+#define MII_CR_SPEED_1000 0x0040
+#define MII_CR_SPEED_100 0x2000
+#define MII_CR_SPEED_10 0x0000
+
+/* PHY Status Register */
+#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */
+#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */
+#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
+#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */
+#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */
+#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
+#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */
+#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */
+#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */
+#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */
+#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */
+#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */
+#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */
+#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */
+#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */
+
+/* Autoneg Advertisement Register */
+#define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */
+#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
+#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
+#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
+#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
+#define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */
+#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
+#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
+#define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */
+#define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */
+
+/* Link Partner Ability Register (Base Page) */
+#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */
+#define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP is 10T Half Duplex Capable */
+#define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP is 10T Full Duplex Capable */
+#define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP is 100TX Half Duplex Capable */
+#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP is 100TX Full Duplex Capable */
+#define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */
+#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
+#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
+#define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP has detected Remote Fault */
+#define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP has rx'd link code word */
+#define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */
+
+/* Autoneg Expansion Register */
+#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */
+#define NWAY_ER_PAGE_RXD 0x0002 /* LP is 10T Half Duplex Capable */
+#define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP is 10T Full Duplex Capable */
+#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */
+#define NWAY_ER_PAR_DETECT_FAULT 0x0010 /* LP is 100TX Full Duplex Capable */
+
+/* 1000BASE-T Control Register */
+#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */
+#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
+#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
+#define CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port */
+ /* 0=DTE device */
+#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
+ /* 0=Configure PHY as Slave */
+#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
+ /* 0=Automatic Master/Slave config */
+#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */
+#define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */
+#define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */
+#define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */
+#define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */
+
+/* 1000BASE-T Status Register */
+#define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle errors since last read */
+#define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asymmetric pause direction bit */
+#define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */
+#define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */
+#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
+#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
+#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local Tx is Master, 0=Slave */
+#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */
+
+#define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT 5
+
+/* PHY 1000 MII Register/Bit Definitions */
+/* PHY Registers defined by IEEE */
+#define PHY_CONTROL 0x00 /* Control Register */
+#define PHY_STATUS 0x01 /* Status Register */
+#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
+#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
+#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
+#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
+#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */
+#define PHY_NEXT_PAGE_TX 0x07 /* Next Page Tx */
+#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */
+#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
+#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
+#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */
+
+#define PHY_CONTROL_LB 0x4000 /* PHY Loopback bit */
+
+/* NVM Control */
+#define E1000_EECD_SK 0x00000001 /* NVM Clock */
+#define E1000_EECD_CS 0x00000002 /* NVM Chip Select */
+#define E1000_EECD_DI 0x00000004 /* NVM Data In */
+#define E1000_EECD_DO 0x00000008 /* NVM Data Out */
+#define E1000_EECD_FWE_MASK 0x00000030
+#define E1000_EECD_FWE_DIS 0x00000010 /* Disable FLASH writes */
+#define E1000_EECD_FWE_EN 0x00000020 /* Enable FLASH writes */
+#define E1000_EECD_FWE_SHIFT 4
+#define E1000_EECD_REQ 0x00000040 /* NVM Access Request */
+#define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */
+#define E1000_EECD_PRES 0x00000100 /* NVM Present */
+#define E1000_EECD_SIZE 0x00000200 /* NVM Size (0=64 word 1=256 word) */
+/* NVM Addressing bits based on type 0=small, 1=large */
+#define E1000_EECD_ADDR_BITS 0x00000400
+#define E1000_EECD_TYPE 0x00002000 /* NVM Type (1-SPI, 0-Microwire) */
+#define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */
+#define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */
+#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */
+#define E1000_EECD_SIZE_EX_SHIFT 11
+#define E1000_EECD_NVADDS 0x00018000 /* NVM Address Size */
+#define E1000_EECD_SELSHAD 0x00020000 /* Select Shadow RAM */
+#define E1000_EECD_INITSRAM 0x00040000 /* Initialize Shadow RAM */
+#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */
+#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */
+#define E1000_EECD_SHADV 0x00200000 /* Shadow RAM Data Valid */
+#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */
+#define E1000_EECD_SECVAL_SHIFT 22
+#define E1000_EECD_SEC1VAL_VALID_MASK (E1000_EECD_AUTO_RD | E1000_EECD_PRES)
+
+#define E1000_NVM_SWDPIN0 0x0001 /* SWDPIN 0 NVM Value */
+#define E1000_NVM_LED_LOGIC 0x0020 /* Led Logic Word */
+#define E1000_NVM_RW_REG_DATA 16 /* Offset to data in NVM read/write regs */
+#define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
+#define E1000_NVM_RW_REG_START 1 /* Start operation */
+#define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
+#define E1000_NVM_POLL_WRITE 1 /* Flag for polling for write complete */
+#define E1000_NVM_POLL_READ 0 /* Flag for polling for read complete */
+#define E1000_FLASH_UPDATES 2000
+
+/* NVM Word Offsets */
+#define NVM_COMPAT 0x0003
+#define NVM_ID_LED_SETTINGS 0x0004
+#define NVM_VERSION 0x0005
+#define NVM_SERDES_AMPLITUDE 0x0006 /* SERDES output amplitude */
+#define NVM_PHY_CLASS_WORD 0x0007
+#define NVM_INIT_CONTROL1_REG 0x000A
+#define NVM_INIT_CONTROL2_REG 0x000F
+#define NVM_SWDEF_PINS_CTRL_PORT_1 0x0010
+#define NVM_INIT_CONTROL3_PORT_B 0x0014
+#define NVM_INIT_3GIO_3 0x001A
+#define NVM_SWDEF_PINS_CTRL_PORT_0 0x0020
+#define NVM_INIT_CONTROL3_PORT_A 0x0024
+#define NVM_CFG 0x0012
+#define NVM_FLASH_VERSION 0x0032
+#define NVM_ALT_MAC_ADDR_PTR 0x0037
+#define NVM_CHECKSUM_REG 0x003F
+
+#define E1000_NVM_CFG_DONE_PORT_0 0x040000 /* MNG config cycle done */
+#define E1000_NVM_CFG_DONE_PORT_1 0x080000 /* ...for second port */
+
+/* Mask bits for fields in Word 0x0f of the NVM */
+#define NVM_WORD0F_PAUSE_MASK 0x3000
+#define NVM_WORD0F_PAUSE 0x1000
+#define NVM_WORD0F_ASM_DIR 0x2000
+#define NVM_WORD0F_ANE 0x0800
+#define NVM_WORD0F_SWPDIO_EXT_MASK 0x00F0
+#define NVM_WORD0F_LPLU 0x0001
+
+/* Mask bits for fields in Word 0x1a of the NVM */
+#define NVM_WORD1A_ASPM_MASK 0x000C
+
+/* For checksumming, the sum of all words in the NVM should equal 0xBABA. */
+#define NVM_SUM 0xBABA
+
+#define NVM_MAC_ADDR_OFFSET 0
+#define NVM_PBA_OFFSET_0 8
+#define NVM_PBA_OFFSET_1 9
+#define NVM_RESERVED_WORD 0xFFFF
+#define NVM_PHY_CLASS_A 0x8000
+#define NVM_SERDES_AMPLITUDE_MASK 0x000F
+#define NVM_SIZE_MASK 0x1C00
+#define NVM_SIZE_SHIFT 10
+#define NVM_WORD_SIZE_BASE_SHIFT 6
+#define NVM_SWDPIO_EXT_SHIFT 4
+
+/* NVM Commands - SPI */
+#define NVM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
+#define NVM_READ_OPCODE_SPI 0x03 /* NVM read opcode */
+#define NVM_WRITE_OPCODE_SPI 0x02 /* NVM write opcode */
+#define NVM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
+#define NVM_WREN_OPCODE_SPI 0x06 /* NVM set Write Enable latch */
+#define NVM_WRDI_OPCODE_SPI 0x04 /* NVM reset Write Enable latch */
+#define NVM_RDSR_OPCODE_SPI 0x05 /* NVM read Status register */
+#define NVM_WRSR_OPCODE_SPI 0x01 /* NVM write Status register */
+
+/* SPI NVM Status Register */
+#define NVM_STATUS_RDY_SPI 0x01
+#define NVM_STATUS_WEN_SPI 0x02
+#define NVM_STATUS_BP0_SPI 0x04
+#define NVM_STATUS_BP1_SPI 0x08
+#define NVM_STATUS_WPEN_SPI 0x80
+
+/* Word definitions for ID LED Settings */
+#define ID_LED_RESERVED_0000 0x0000
+#define ID_LED_RESERVED_FFFF 0xFFFF
+#define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
+ (ID_LED_OFF1_OFF2 << 8) | \
+ (ID_LED_DEF1_DEF2 << 4) | \
+ (ID_LED_DEF1_DEF2))
+#define ID_LED_DEF1_DEF2 0x1
+#define ID_LED_DEF1_ON2 0x2
+#define ID_LED_DEF1_OFF2 0x3
+#define ID_LED_ON1_DEF2 0x4
+#define ID_LED_ON1_ON2 0x5
+#define ID_LED_ON1_OFF2 0x6
+#define ID_LED_OFF1_DEF2 0x7
+#define ID_LED_OFF1_ON2 0x8
+#define ID_LED_OFF1_OFF2 0x9
+
+#define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF
+#define IGP_ACTIVITY_LED_ENABLE 0x0300
+#define IGP_LED3_MODE 0x07000000
+
+/* PCI/PCI-X/PCI-EX Config space */
+#define PCI_HEADER_TYPE_REGISTER 0x0E
+#define PCIE_LINK_STATUS 0x12
+#define PCIE_DEVICE_CONTROL2 0x28
+
+#define PCI_HEADER_TYPE_MULTIFUNC 0x80
+#define PCIE_LINK_WIDTH_MASK 0x3F0
+#define PCIE_LINK_WIDTH_SHIFT 4
+#define PCIE_DEVICE_CONTROL2_16ms 0x0005
+
+#ifndef ETH_ADDR_LEN
+#define ETH_ADDR_LEN 6
+#endif
+
+#define PHY_REVISION_MASK 0xFFFFFFF0
+#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
+#define MAX_PHY_MULTI_PAGE_REG 0xF
+
+/* Bit definitions for valid PHY IDs. */
+/*
+ * I = Integrated
+ * E = External
+ */
+#define M88E1000_E_PHY_ID 0x01410C50
+#define M88E1000_I_PHY_ID 0x01410C30
+#define M88E1011_I_PHY_ID 0x01410C20
+#define IGP01E1000_I_PHY_ID 0x02A80380
+#define M88E1011_I_REV_4 0x04
+#define M88E1111_I_PHY_ID 0x01410CC0
+#define GG82563_E_PHY_ID 0x01410CA0
+#define IGP03E1000_E_PHY_ID 0x02A80390
+#define IFE_E_PHY_ID 0x02A80330
+#define IFE_PLUS_E_PHY_ID 0x02A80320
+#define IFE_C_E_PHY_ID 0x02A80310
+#define BME1000_E_PHY_ID 0x01410CB0
+#define BME1000_E_PHY_ID_R2 0x01410CB1
+#define I82577_E_PHY_ID 0x01540050
+#define I82578_E_PHY_ID 0x004DD040
+#define M88_VENDOR 0x0141
+
+/* M88E1000 Specific Registers */
+#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
+#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
+#define M88E1000_INT_ENABLE 0x12 /* Interrupt Enable Register */
+#define M88E1000_INT_STATUS 0x13 /* Interrupt Status Register */
+#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
+#define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */
+
+#define M88E1000_PHY_EXT_CTRL 0x1A /* PHY extend control register */
+#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
+#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
+#define M88E1000_PHY_VCO_REG_BIT8 0x100 /* Bits 8 & 11 are adjusted for */
+#define M88E1000_PHY_VCO_REG_BIT11 0x800 /* improved BER performance */
+
+/* M88E1000 PHY Specific Control Register */
+#define M88E1000_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */
+#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reverse enabled */
+#define M88E1000_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */
+/* 1=CLK125 low, 0=CLK125 toggling */
+#define M88E1000_PSCR_CLK125_DISABLE 0x0010
+#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
+ /* Manual MDI configuration */
+#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
+/* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */
+#define M88E1000_PSCR_AUTO_X_1000T 0x0040
+/* Auto crossover enabled all speeds */
+#define M88E1000_PSCR_AUTO_X_MODE 0x0060
+/*
+ * 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold
+ * 0=Normal 10BASE-T Rx Threshold
+ */
+#define M88E1000_PSCR_EN_10BT_EXT_DIST 0x0080
+/* 1=5-bit interface in 100BASE-TX, 0=MII interface in 100BASE-TX */
+#define M88E1000_PSCR_MII_5BIT_ENABLE 0x0100
+#define M88E1000_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */
+#define M88E1000_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */
+#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Tx */
+
+/* M88E1000 PHY Specific Status Register */
+#define M88E1000_PSSR_JABBER 0x0001 /* 1=Jabber */
+#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
+#define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */
+#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
+/*
+ * 0 = <50M
+ * 1 = 50-80M
+ * 2 = 80-110M
+ * 3 = 110-140M
+ * 4 = >140M
+ */
+#define M88E1000_PSSR_CABLE_LENGTH 0x0380
+#define M88E1000_PSSR_LINK 0x0400 /* 1=Link up, 0=Link down */
+#define M88E1000_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */
+#define M88E1000_PSSR_PAGE_RCVD 0x1000 /* 1=Page received */
+#define M88E1000_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */
+#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
+#define M88E1000_PSSR_10MBS 0x0000 /* 00=10Mbs */
+#define M88E1000_PSSR_100MBS 0x4000 /* 01=100Mbs */
+#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
+
+#define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
+
+/* M88E1000 Extended PHY Specific Control Register */
+#define M88E1000_EPSCR_FIBER_LOOPBACK 0x4000 /* 1=Fiber loopback */
+/*
+ * 1 = Lost lock detect enabled.
+ * Will assert lost lock and bring
+ * link down if idle not seen
+ * within 1ms in 1000BASE-T
+ */
+#define M88E1000_EPSCR_DOWN_NO_IDLE 0x8000
+/*
+ * Number of times we will attempt to autonegotiate before downshifting if we
+ * are the master
+ */
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_2X 0x0400
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_3X 0x0800
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_4X 0x0C00
+/*
+ * Number of times we will attempt to autonegotiate before downshifting if we
+ * are the slave
+ */
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_DIS 0x0000
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_2X 0x0200
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_3X 0x0300
+#define M88E1000_EPSCR_TX_CLK_2_5 0x0060 /* 2.5 MHz TX_CLK */
+#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
+#define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */
+
+/* M88EC018 Rev 2 specific DownShift settings */
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_1X 0x0000
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_2X 0x0200
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_3X 0x0400
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_4X 0x0600
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_6X 0x0A00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_7X 0x0C00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_8X 0x0E00
+
+#define I82578_EPSCR_DOWNSHIFT_ENABLE 0x0020
+#define I82578_EPSCR_DOWNSHIFT_COUNTER_MASK 0x001C
+
+/* BME1000 PHY Specific Control Register */
+#define BME1000_PSCR_ENABLE_DOWNSHIFT 0x0800 /* 1 = enable downshift */
+
+/*
+ * Bits...
+ * 15-5: page
+ * 4-0: register offset
+ */
+#define GG82563_PAGE_SHIFT 5
+#define GG82563_REG(page, reg) \
+ (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
+#define GG82563_MIN_ALT_REG 30
+
+/* GG82563 Specific Registers */
+#define GG82563_PHY_SPEC_CTRL \
+ GG82563_REG(0, 16) /* PHY Specific Control */
+#define GG82563_PHY_SPEC_STATUS \
+ GG82563_REG(0, 17) /* PHY Specific Status */
+#define GG82563_PHY_INT_ENABLE \
+ GG82563_REG(0, 18) /* Interrupt Enable */
+#define GG82563_PHY_SPEC_STATUS_2 \
+ GG82563_REG(0, 19) /* PHY Specific Status 2 */
+#define GG82563_PHY_RX_ERR_CNTR \
+ GG82563_REG(0, 21) /* Receive Error Counter */
+#define GG82563_PHY_PAGE_SELECT \
+ GG82563_REG(0, 22) /* Page Select */
+#define GG82563_PHY_SPEC_CTRL_2 \
+ GG82563_REG(0, 26) /* PHY Specific Control 2 */
+#define GG82563_PHY_PAGE_SELECT_ALT \
+ GG82563_REG(0, 29) /* Alternate Page Select */
+#define GG82563_PHY_TEST_CLK_CTRL \
+ GG82563_REG(0, 30) /* Test Clock Control (use reg. 29 to select) */
+
+#define GG82563_PHY_MAC_SPEC_CTRL \
+ GG82563_REG(2, 21) /* MAC Specific Control Register */
+#define GG82563_PHY_MAC_SPEC_CTRL_2 \
+ GG82563_REG(2, 26) /* MAC Specific Control 2 */
+
+#define GG82563_PHY_DSP_DISTANCE \
+ GG82563_REG(5, 26) /* DSP Distance */
+
+/* Page 193 - Port Control Registers */
+#define GG82563_PHY_KMRN_MODE_CTRL \
+ GG82563_REG(193, 16) /* Kumeran Mode Control */
+#define GG82563_PHY_PORT_RESET \
+ GG82563_REG(193, 17) /* Port Reset */
+#define GG82563_PHY_REVISION_ID \
+ GG82563_REG(193, 18) /* Revision ID */
+#define GG82563_PHY_DEVICE_ID \
+ GG82563_REG(193, 19) /* Device ID */
+#define GG82563_PHY_PWR_MGMT_CTRL \
+ GG82563_REG(193, 20) /* Power Management Control */
+#define GG82563_PHY_RATE_ADAPT_CTRL \
+ GG82563_REG(193, 25) /* Rate Adaptation Control */
+
+/* Page 194 - KMRN Registers */
+#define GG82563_PHY_KMRN_FIFO_CTRL_STAT \
+ GG82563_REG(194, 16) /* FIFO's Control/Status */
+#define GG82563_PHY_KMRN_CTRL \
+ GG82563_REG(194, 17) /* Control */
+#define GG82563_PHY_INBAND_CTRL \
+ GG82563_REG(194, 18) /* Inband Control */
+#define GG82563_PHY_KMRN_DIAGNOSTIC \
+ GG82563_REG(194, 19) /* Diagnostic */
+#define GG82563_PHY_ACK_TIMEOUTS \
+ GG82563_REG(194, 20) /* Acknowledge Timeouts */
+#define GG82563_PHY_ADV_ABILITY \
+ GG82563_REG(194, 21) /* Advertised Ability */
+#define GG82563_PHY_LINK_PARTNER_ADV_ABILITY \
+ GG82563_REG(194, 23) /* Link Partner Advertised Ability */
+#define GG82563_PHY_ADV_NEXT_PAGE \
+ GG82563_REG(194, 24) /* Advertised Next Page */
+#define GG82563_PHY_LINK_PARTNER_ADV_NEXT_PAGE \
+ GG82563_REG(194, 25) /* Link Partner Advertised Next page */
+#define GG82563_PHY_KMRN_MISC \
+ GG82563_REG(194, 26) /* Misc. */
+
+/* MDI Control */
+#define E1000_MDIC_DATA_MASK 0x0000FFFF
+#define E1000_MDIC_REG_MASK 0x001F0000
+#define E1000_MDIC_REG_SHIFT 16
+#define E1000_MDIC_PHY_MASK 0x03E00000
+#define E1000_MDIC_PHY_SHIFT 21
+#define E1000_MDIC_OP_WRITE 0x04000000
+#define E1000_MDIC_OP_READ 0x08000000
+#define E1000_MDIC_READY 0x10000000
+#define E1000_MDIC_INT_EN 0x20000000
+#define E1000_MDIC_ERROR 0x40000000
+
+/* SerDes Control */
+#define E1000_GEN_CTL_READY 0x80000000
+#define E1000_GEN_CTL_ADDRESS_SHIFT 8
+#define E1000_GEN_POLL_TIMEOUT 640
+
+
+
+#endif /* _E1000E_DEFINES_H_ */
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#ifndef _E1000E_HW_H_
+#define _E1000E_HW_H_
+
+#include "e1000e_regs.h"
+#include "e1000e_defines.h"
+
+struct e1000_hw;
+
+#define E1000_DEV_ID_82571EB_COPPER 0x105E
+#define E1000_DEV_ID_82571EB_FIBER 0x105F
+#define E1000_DEV_ID_82571EB_SERDES 0x1060
+#define E1000_DEV_ID_82571EB_SERDES_DUAL 0x10D9
+#define E1000_DEV_ID_82571EB_SERDES_QUAD 0x10DA
+#define E1000_DEV_ID_82571EB_QUAD_COPPER 0x10A4
+#define E1000_DEV_ID_82571PT_QUAD_COPPER 0x10D5
+#define E1000_DEV_ID_82571EB_QUAD_FIBER 0x10A5
+#define E1000_DEV_ID_82571EB_QUAD_COPPER_LP 0x10BC
+#define E1000_DEV_ID_82572EI_COPPER 0x107D
+#define E1000_DEV_ID_82572EI_FIBER 0x107E
+#define E1000_DEV_ID_82572EI_SERDES 0x107F
+#define E1000_DEV_ID_82572EI 0x10B9
+#define E1000_DEV_ID_82573E 0x108B
+#define E1000_DEV_ID_82573E_IAMT 0x108C
+#define E1000_DEV_ID_82573L 0x109A
+#define E1000_DEV_ID_82574L 0x10D3
+#define E1000_DEV_ID_82574LA 0x10F6
+#define E1000_DEV_ID_82583V 0x150C
+#define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096
+#define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098
+#define E1000_DEV_ID_80003ES2LAN_COPPER_SPT 0x10BA
+#define E1000_DEV_ID_80003ES2LAN_SERDES_SPT 0x10BB
+#define E1000_DEV_ID_ICH8_82567V_3 0x1501
+#define E1000_DEV_ID_ICH8_IGP_M_AMT 0x1049
+#define E1000_DEV_ID_ICH8_IGP_AMT 0x104A
+#define E1000_DEV_ID_ICH8_IGP_C 0x104B
+#define E1000_DEV_ID_ICH8_IFE 0x104C
+#define E1000_DEV_ID_ICH8_IFE_GT 0x10C4
+#define E1000_DEV_ID_ICH8_IFE_G 0x10C5
+#define E1000_DEV_ID_ICH8_IGP_M 0x104D
+#define E1000_DEV_ID_ICH9_IGP_M 0x10BF
+#define E1000_DEV_ID_ICH9_IGP_M_AMT 0x10F5
+#define E1000_DEV_ID_ICH9_IGP_M_V 0x10CB
+#define E1000_DEV_ID_ICH9_IGP_AMT 0x10BD
+#define E1000_DEV_ID_ICH9_BM 0x10E5
+#define E1000_DEV_ID_ICH9_IGP_C 0x294C
+#define E1000_DEV_ID_ICH9_IFE 0x10C0
+#define E1000_DEV_ID_ICH9_IFE_GT 0x10C3
+#define E1000_DEV_ID_ICH9_IFE_G 0x10C2
+#define E1000_DEV_ID_ICH10_R_BM_LM 0x10CC
+#define E1000_DEV_ID_ICH10_R_BM_LF 0x10CD
+#define E1000_DEV_ID_ICH10_R_BM_V 0x10CE
+#define E1000_DEV_ID_ICH10_D_BM_LM 0x10DE
+#define E1000_DEV_ID_ICH10_D_BM_LF 0x10DF
+#define E1000_DEV_ID_PCH_M_HV_LM 0x10EA
+#define E1000_DEV_ID_PCH_M_HV_LC 0x10EB
+#define E1000_DEV_ID_PCH_D_HV_DM 0x10EF
+#define E1000_DEV_ID_PCH_D_HV_DC 0x10F0
+#define E1000_REVISION_0 0
+#define E1000_REVISION_1 1
+#define E1000_REVISION_2 2
+#define E1000_REVISION_3 3
+#define E1000_REVISION_4 4
+
+#define E1000_FUNC_0 0
+#define E1000_FUNC_1 1
+
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN0 0
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN1 3
+
+enum e1000_mac_type {
+ e1000_undefined = 0,
+ e1000_82571,
+ e1000_82572,
+ e1000_82573,
+ e1000_82574,
+ e1000_82583,
+ e1000_80003es2lan,
+ e1000_ich8lan,
+ e1000_ich9lan,
+ e1000_ich10lan,
+ e1000_pchlan,
+ e1000_num_macs /* List is 1-based, so subtract 1 for true count. */
+};
+
+enum e1000_media_type {
+ e1000_media_type_unknown = 0,
+ e1000_media_type_copper = 1,
+ e1000_media_type_fiber = 2,
+ e1000_media_type_internal_serdes = 3,
+ e1000_num_media_types
+};
+
+enum e1000_nvm_type {
+ e1000_nvm_unknown = 0,
+ e1000_nvm_none,
+ e1000_nvm_eeprom_spi,
+ e1000_nvm_flash_hw,
+ e1000_nvm_flash_sw
+};
+
+enum e1000_nvm_override {
+ e1000_nvm_override_none = 0,
+ e1000_nvm_override_spi_small,
+ e1000_nvm_override_spi_large,
+};
+
+enum e1000_phy_type {
+ e1000_phy_unknown = 0,
+ e1000_phy_none,
+ e1000_phy_m88,
+ e1000_phy_igp,
+ e1000_phy_igp_2,
+ e1000_phy_gg82563,
+ e1000_phy_igp_3,
+ e1000_phy_ife,
+ e1000_phy_bm,
+ e1000_phy_82578,
+ e1000_phy_82577,
+};
+
+enum e1000_bus_type {
+ e1000_bus_type_unknown = 0,
+ e1000_bus_type_pci,
+ e1000_bus_type_pcix,
+ e1000_bus_type_pci_express,
+ e1000_bus_type_reserved
+};
+
+enum e1000_bus_speed {
+ e1000_bus_speed_unknown = 0,
+ e1000_bus_speed_33,
+ e1000_bus_speed_66,
+ e1000_bus_speed_100,
+ e1000_bus_speed_120,
+ e1000_bus_speed_133,
+ e1000_bus_speed_2500,
+ e1000_bus_speed_5000,
+ e1000_bus_speed_reserved
+};
+
+enum e1000_bus_width {
+ e1000_bus_width_unknown = 0,
+ e1000_bus_width_pcie_x1,
+ e1000_bus_width_pcie_x2,
+ e1000_bus_width_pcie_x4 = 4,
+ e1000_bus_width_pcie_x8 = 8,
+ e1000_bus_width_32,
+ e1000_bus_width_64,
+ e1000_bus_width_reserved
+};
+
+enum e1000_1000t_rx_status {
+ e1000_1000t_rx_status_not_ok = 0,
+ e1000_1000t_rx_status_ok,
+ e1000_1000t_rx_status_undefined = 0xFF
+};
+
+enum e1000_rev_polarity {
+ e1000_rev_polarity_normal = 0,
+ e1000_rev_polarity_reversed,
+ e1000_rev_polarity_undefined = 0xFF
+};
+
+enum e1000_fc_mode {
+ e1000_fc_none = 0,
+ e1000_fc_rx_pause,
+ e1000_fc_tx_pause,
+ e1000_fc_full,
+ e1000_fc_default = 0xFF
+};
+
+enum e1000_ms_type {
+ e1000_ms_hw_default = 0,
+ e1000_ms_force_master,
+ e1000_ms_force_slave,
+ e1000_ms_auto
+};
+
+enum e1000_smart_speed {
+ e1000_smart_speed_default = 0,
+ e1000_smart_speed_on,
+ e1000_smart_speed_off
+};
+
+enum e1000_serdes_link_state {
+ e1000_serdes_link_down = 0,
+ e1000_serdes_link_autoneg_progress,
+ e1000_serdes_link_autoneg_complete,
+ e1000_serdes_link_forced_up
+};
+
+/* Receive Descriptor */
+struct e1000_rx_desc {
+ __le64 buffer_addr; /* Address of the descriptor's data buffer */
+ __le16 length; /* Length of data DMAed into data buffer */
+ __le16 csum; /* Packet checksum */
+ u8 status; /* Descriptor status */
+ u8 errors; /* Descriptor Errors */
+ __le16 special;
+};
+
+/* Receive Descriptor - Extended */
+union e1000_rx_desc_extended {
+ struct {
+ __le64 buffer_addr;
+ __le64 reserved;
+ } read;
+ struct {
+ struct {
+ __le32 mrq; /* Multiple Rx Queues */
+ union {
+ __le32 rss; /* RSS Hash */
+ struct {
+ __le16 ip_id; /* IP id */
+ __le16 csum; /* Packet Checksum */
+ } csum_ip;
+ } hi_dword;
+ } lower;
+ struct {
+ __le32 status_error; /* ext status/error */
+ __le16 length;
+ __le16 vlan; /* VLAN tag */
+ } upper;
+ } wb; /* writeback */
+};
+
+#define MAX_PS_BUFFERS 4
+/* Receive Descriptor - Packet Split */
+union e1000_rx_desc_packet_split {
+ struct {
+ /* one buffer for protocol header(s), three data buffers */
+ __le64 buffer_addr[MAX_PS_BUFFERS];
+ } read;
+ struct {
+ struct {
+ __le32 mrq; /* Multiple Rx Queues */
+ union {
+ __le32 rss; /* RSS Hash */
+ struct {
+ __le16 ip_id; /* IP id */
+ __le16 csum; /* Packet Checksum */
+ } csum_ip;
+ } hi_dword;
+ } lower;
+ struct {
+ __le32 status_error; /* ext status/error */
+ __le16 length0; /* length of buffer 0 */
+ __le16 vlan; /* VLAN tag */
+ } middle;
+ struct {
+ __le16 header_status;
+ __le16 length[3]; /* length of buffers 1-3 */
+ } upper;
+ __le64 reserved;
+ } wb; /* writeback */
+};
+
+/* Transmit Descriptor */
+struct e1000_tx_desc {
+ __le64 buffer_addr; /* Address of the descriptor's data buffer */
+ union {
+ __le32 data;
+ struct {
+ __le16 length; /* Data buffer length */
+ u8 cso; /* Checksum offset */
+ u8 cmd; /* Descriptor control */
+ } flags;
+ } lower;
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 css; /* Checksum start */
+ __le16 special;
+ } fields;
+ } upper;
+};
+
+/* Offload Context Descriptor */
+struct e1000_context_desc {
+ union {
+ __le32 ip_config;
+ struct {
+ u8 ipcss; /* IP checksum start */
+ u8 ipcso; /* IP checksum offset */
+ __le16 ipcse; /* IP checksum end */
+ } ip_fields;
+ } lower_setup;
+ union {
+ __le32 tcp_config;
+ struct {
+ u8 tucss; /* TCP checksum start */
+ u8 tucso; /* TCP checksum offset */
+ __le16 tucse; /* TCP checksum end */
+ } tcp_fields;
+ } upper_setup;
+ __le32 cmd_and_length;
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 hdr_len; /* Header length */
+ __le16 mss; /* Maximum segment size */
+ } fields;
+ } tcp_seg_setup;
+};
+
+/* Offload data descriptor */
+struct e1000_data_desc {
+ __le64 buffer_addr; /* Address of the descriptor's buffer address */
+ union {
+ __le32 data;
+ struct {
+ __le16 length; /* Data buffer length */
+ u8 typ_len_ext;
+ u8 cmd;
+ } flags;
+ } lower;
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 popts; /* Packet Options */
+ __le16 special;
+ } fields;
+ } upper;
+};
+
+/* Statistics counters collected by the MAC */
+struct e1000_hw_stats {
+ u64 crcerrs;
+ u64 algnerrc;
+ u64 symerrs;
+ u64 rxerrc;
+ u64 mpc;
+ u64 scc;
+ u64 ecol;
+ u64 mcc;
+ u64 latecol;
+ u64 colc;
+ u64 dc;
+ u64 tncrs;
+ u64 sec;
+ u64 cexterr;
+ u64 rlec;
+ u64 xonrxc;
+ u64 xontxc;
+ u64 xoffrxc;
+ u64 xofftxc;
+ u64 fcruc;
+ u64 prc64;
+ u64 prc127;
+ u64 prc255;
+ u64 prc511;
+ u64 prc1023;
+ u64 prc1522;
+ u64 gprc;
+ u64 bprc;
+ u64 mprc;
+ u64 gptc;
+ u64 gorc;
+ u64 gotc;
+ u64 rnbc;
+ u64 ruc;
+ u64 rfc;
+ u64 roc;
+ u64 rjc;
+ u64 mgprc;
+ u64 mgpdc;
+ u64 mgptc;
+ u64 tor;
+ u64 tot;
+ u64 tpr;
+ u64 tpt;
+ u64 ptc64;
+ u64 ptc127;
+ u64 ptc255;
+ u64 ptc511;
+ u64 ptc1023;
+ u64 ptc1522;
+ u64 mptc;
+ u64 bptc;
+ u64 tsctc;
+ u64 tsctfc;
+ u64 iac;
+ u64 icrxptc;
+ u64 icrxatc;
+ u64 ictxptc;
+ u64 ictxatc;
+ u64 ictxqec;
+ u64 ictxqmtc;
+ u64 icrxdmtc;
+ u64 icrxoc;
+ u64 doosync;
+};
+
+
+struct e1000_phy_stats {
+ u32 idle_errors;
+ u32 receive_errors;
+};
+
+struct e1000_host_mng_dhcp_cookie {
+ u32 signature;
+ u8 status;
+ u8 reserved0;
+ u16 vlan_id;
+ u32 reserved1;
+ u16 reserved2;
+ u8 reserved3;
+ u8 checksum;
+};
+
+/* Host Interface "Rev 1" */
+struct e1000_host_command_header {
+ u8 command_id;
+ u8 command_length;
+ u8 command_options;
+ u8 checksum;
+};
+
+#define E1000_HI_MAX_DATA_LENGTH 252
+struct e1000_host_command_info {
+ struct e1000_host_command_header command_header;
+ u8 command_data[E1000_HI_MAX_DATA_LENGTH];
+};
+
+/* Host Interface "Rev 2" */
+struct e1000_host_mng_command_header {
+ u8 command_id;
+ u8 checksum;
+ u16 reserved1;
+ u16 reserved2;
+ u16 command_length;
+};
+
+#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8
+struct e1000_host_mng_command_info {
+ struct e1000_host_mng_command_header command_header;
+ u8 command_data[E1000_HI_MAX_MNG_DATA_LENGTH];
+};
+
+#include "e1000e_mac.h"
+#include "e1000e_phy.h"
+#include "e1000e_nvm.h"
+#include "e1000e_manage.h"
+
+struct e1000_mac_operations {
+ /* Function pointers for the MAC. */
+ s32 (*init_params)(struct e1000_hw *);
+ s32 (*id_led_init)(struct e1000_hw *);
+ s32 (*blink_led)(struct e1000_hw *);
+ s32 (*check_for_link)(struct e1000_hw *);
+ bool (*check_mng_mode)(struct e1000_hw *hw);
+ s32 (*cleanup_led)(struct e1000_hw *);
+ void (*clear_hw_cntrs)(struct e1000_hw *);
+ void (*clear_vfta)(struct e1000_hw *);
+ s32 (*get_bus_info)(struct e1000_hw *);
+ void (*set_lan_id)(struct e1000_hw *);
+ s32 (*get_link_up_info)(struct e1000_hw *, u16 *, u16 *);
+ s32 (*led_on)(struct e1000_hw *);
+ s32 (*led_off)(struct e1000_hw *);
+ void (*update_mc_addr_list)(struct e1000_hw *, u8 *, u32);
+ s32 (*reset_hw)(struct e1000_hw *);
+ s32 (*init_hw)(struct e1000_hw *);
+ s32 (*setup_link)(struct e1000_hw *);
+ s32 (*setup_physical_interface)(struct e1000_hw *);
+ s32 (*setup_led)(struct e1000_hw *);
+ void (*write_vfta)(struct e1000_hw *, u32, u32);
+ void (*mta_set)(struct e1000_hw *, u32);
+ void (*config_collision_dist)(struct e1000_hw *);
+ void (*rar_set)(struct e1000_hw *, u8*, u32);
+ s32 (*read_mac_addr)(struct e1000_hw *);
+ s32 (*validate_mdi_setting)(struct e1000_hw *);
+ s32 (*mng_host_if_write)(struct e1000_hw *, u8*, u16, u16, u8*);
+ s32 (*mng_write_cmd_header)(struct e1000_hw *hw,
+ struct e1000_host_mng_command_header*);
+ s32 (*mng_enable_host_if)(struct e1000_hw *);
+ s32 (*wait_autoneg)(struct e1000_hw *);
+};
+
+struct e1000_phy_operations {
+ s32 (*init_params)(struct e1000_hw *);
+ s32 (*acquire)(struct e1000_hw *);
+ s32 (*cfg_on_link_up)(struct e1000_hw *);
+ s32 (*check_polarity)(struct e1000_hw *);
+ s32 (*check_reset_block)(struct e1000_hw *);
+ s32 (*commit)(struct e1000_hw *);
+#if 0
+ s32 (*force_speed_duplex)(struct e1000_hw *);
+#endif
+ s32 (*get_cfg_done)(struct e1000_hw *hw);
+#if 0
+ s32 (*get_cable_length)(struct e1000_hw *);
+#endif
+ s32 (*get_info)(struct e1000_hw *);
+ s32 (*read_reg)(struct e1000_hw *, u32, u16 *);
+ s32 (*read_reg_locked)(struct e1000_hw *, u32, u16 *);
+ void (*release)(struct e1000_hw *);
+ s32 (*reset)(struct e1000_hw *);
+ s32 (*set_d0_lplu_state)(struct e1000_hw *, bool);
+ s32 (*set_d3_lplu_state)(struct e1000_hw *, bool);
+ s32 (*write_reg)(struct e1000_hw *, u32, u16);
+ s32 (*write_reg_locked)(struct e1000_hw *, u32, u16);
+ void (*power_up)(struct e1000_hw *);
+ void (*power_down)(struct e1000_hw *);
+};
+
+struct e1000_nvm_operations {
+ s32 (*init_params)(struct e1000_hw *);
+ s32 (*acquire)(struct e1000_hw *);
+ s32 (*read)(struct e1000_hw *, u16, u16, u16 *);
+ void (*release)(struct e1000_hw *);
+ void (*reload)(struct e1000_hw *);
+ s32 (*update)(struct e1000_hw *);
+ s32 (*valid_led_default)(struct e1000_hw *, u16 *);
+ s32 (*validate)(struct e1000_hw *);
+ s32 (*write)(struct e1000_hw *, u16, u16, u16 *);
+};
+
+struct e1000_mac_info {
+ struct e1000_mac_operations ops;
+ u8 addr[6];
+ u8 perm_addr[6];
+
+ enum e1000_mac_type type;
+
+ u32 collision_delta;
+ u32 ledctl_default;
+ u32 ledctl_mode1;
+ u32 ledctl_mode2;
+ u32 mc_filter_type;
+ u32 tx_packet_delta;
+ u32 txcw;
+
+ u16 current_ifs_val;
+ u16 ifs_max_val;
+ u16 ifs_min_val;
+ u16 ifs_ratio;
+ u16 ifs_step_size;
+ u16 mta_reg_count;
+
+ /* Maximum size of the MTA register table in all supported adapters */
+ #define MAX_MTA_REG 128
+ u32 mta_shadow[MAX_MTA_REG];
+ u16 rar_entry_count;
+
+ u8 forced_speed_duplex;
+
+ bool adaptive_ifs;
+ bool arc_subsystem_valid;
+ bool asf_firmware_present;
+ bool autoneg;
+ bool autoneg_failed;
+ bool get_link_status;
+ bool in_ifs_mode;
+ enum e1000_serdes_link_state serdes_link_state;
+ bool serdes_has_link;
+ bool tx_pkt_filtering;
+};
+
+struct e1000_phy_info {
+ struct e1000_phy_operations ops;
+ enum e1000_phy_type type;
+
+ enum e1000_1000t_rx_status local_rx;
+ enum e1000_1000t_rx_status remote_rx;
+ enum e1000_ms_type ms_type;
+ enum e1000_ms_type original_ms_type;
+ enum e1000_rev_polarity cable_polarity;
+ enum e1000_smart_speed smart_speed;
+
+ u32 addr;
+ u32 id;
+ u32 reset_delay_us; /* in usec */
+ u32 revision;
+
+ enum e1000_media_type media_type;
+
+ u16 autoneg_advertised;
+ u16 autoneg_mask;
+ u16 cable_length;
+ u16 max_cable_length;
+ u16 min_cable_length;
+
+ u8 mdix;
+
+ bool disable_polarity_correction;
+ bool is_mdix;
+ bool polarity_correction;
+ bool reset_disable;
+ bool speed_downgraded;
+ bool autoneg_wait_to_complete;
+};
+
+struct e1000_nvm_info {
+ struct e1000_nvm_operations ops;
+ enum e1000_nvm_type type;
+ enum e1000_nvm_override override;
+
+ u32 flash_bank_size;
+ u32 flash_base_addr;
+
+ u16 word_size;
+ u16 delay_usec;
+ u16 address_bits;
+ u16 opcode_bits;
+ u16 page_size;
+};
+
+struct e1000_bus_info {
+ enum e1000_bus_type type;
+ enum e1000_bus_speed speed;
+ enum e1000_bus_width width;
+
+ u16 func;
+ u16 pci_cmd_word;
+};
+
+struct e1000_fc_info {
+ u32 high_water; /* Flow control high-water mark */
+ u32 low_water; /* Flow control low-water mark */
+ u16 pause_time; /* Flow control pause timer */
+ bool send_xon; /* Flow control send XON */
+ bool strict_ieee; /* Strict IEEE mode */
+ enum e1000_fc_mode current_mode; /* FC mode in effect */
+ enum e1000_fc_mode requested_mode; /* FC mode requested by caller */
+};
+
+struct e1000_dev_spec_82571 {
+ bool laa_is_present;
+ u32 smb_counter;
+};
+
+struct e1000_dev_spec_80003es2lan {
+ bool mdic_wa_enable;
+};
+
+struct e1000_shadow_ram {
+ u16 value;
+ bool modified;
+};
+
+#define E1000_ICH8_SHADOW_RAM_WORDS 2048
+
+struct e1000_dev_spec_ich8lan {
+ bool kmrn_lock_loss_workaround_enabled;
+ struct e1000_shadow_ram shadow_ram[E1000_ICH8_SHADOW_RAM_WORDS];
+ bool nvm_k1_enabled;
+};
+
+struct e1000_hw {
+ struct e1000_adapter *adapter;
+
+ u8 __iomem *hw_addr;
+ u8 __iomem *flash_address;
+
+ void *back;
+ unsigned long io_base;
+
+ struct e1000_mac_info mac;
+ struct e1000_fc_info fc;
+ struct e1000_phy_info phy;
+ struct e1000_nvm_info nvm;
+ struct e1000_bus_info bus;
+ struct e1000_host_mng_dhcp_cookie mng_cookie;
+
+ union {
+ struct e1000_dev_spec_82571 _82571;
+ struct e1000_dev_spec_80003es2lan _80003es2lan;
+ struct e1000_dev_spec_ich8lan ich8lan;
+ } dev_spec;
+
+ u16 device_id;
+ u16 subsystem_vendor_id;
+ u16 subsystem_device_id;
+ u16 vendor_id;
+
+ u8 revision_id;
+};
+
+#include "e1000e_82571.h"
+#include "e1000e_80003es2lan.h"
+#include "e1000e_ich8lan.h"
+
+/* These functions must be implemented by drivers */
+s32 e1000e_read_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value);
+
+#endif
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+/*
+ * 82562G 10/100 Network Connection
+ * 82562G-2 10/100 Network Connection
+ * 82562GT 10/100 Network Connection
+ * 82562GT-2 10/100 Network Connection
+ * 82562V 10/100 Network Connection
+ * 82562V-2 10/100 Network Connection
+ * 82566DC-2 Gigabit Network Connection
+ * 82566DC Gigabit Network Connection
+ * 82566DM-2 Gigabit Network Connection
+ * 82566DM Gigabit Network Connection
+ * 82566MC Gigabit Network Connection
+ * 82566MM Gigabit Network Connection
+ * 82567LM Gigabit Network Connection
+ * 82567LF Gigabit Network Connection
+ * 82567V Gigabit Network Connection
+ * 82567LM-2 Gigabit Network Connection
+ * 82567LF-2 Gigabit Network Connection
+ * 82567V-2 Gigabit Network Connection
+ * 82567LF-3 Gigabit Network Connection
+ * 82567LM-3 Gigabit Network Connection
+ * 82567LM-4 Gigabit Network Connection
+ * 82577LM Gigabit Network Connection
+ * 82577LC Gigabit Network Connection
+ * 82578DM Gigabit Network Connection
+ * 82578DC Gigabit Network Connection
+ */
+
+#include "e1000e.h"
+
+static s32 e1000e_init_phy_params_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_init_phy_params_pchlan(struct e1000_hw *hw);
+static s32 e1000e_init_nvm_params_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_init_mac_params_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_acquire_swflag_ich8lan(struct e1000_hw *hw);
+static void e1000e_release_swflag_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_acquire_nvm_ich8lan(struct e1000_hw *hw);
+static void e1000e_release_nvm_ich8lan(struct e1000_hw *hw);
+static bool e1000e_check_mng_mode_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_check_reset_block_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_phy_hw_reset_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_get_phy_info_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_set_lplu_state_pchlan(struct e1000_hw *hw, bool active);
+static s32 e1000e_set_d0_lplu_state_ich8lan(struct e1000_hw *hw,
+ bool active);
+static s32 e1000e_set_d3_lplu_state_ich8lan(struct e1000_hw *hw,
+ bool active);
+static s32 e1000e_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data);
+static s32 e1000e_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data);
+static s32 e1000e_validate_nvm_checksum_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_update_nvm_checksum_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_valid_led_default_ich8lan(struct e1000_hw *hw,
+ u16 *data);
+static s32 e1000e_id_led_init_pchlan(struct e1000_hw *hw);
+static s32 e1000e_get_bus_info_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_reset_hw_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_init_hw_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_setup_link_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_setup_copper_link_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_get_link_up_info_ich8lan(struct e1000_hw *hw,
+ u16 *speed, u16 *duplex);
+static s32 e1000e_cleanup_led_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_led_on_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_led_off_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_k1_gig_workaround_hv(struct e1000_hw *hw, bool link);
+static s32 e1000e_setup_led_pchlan(struct e1000_hw *hw);
+static s32 e1000e_cleanup_led_pchlan(struct e1000_hw *hw);
+static s32 e1000e_led_on_pchlan(struct e1000_hw *hw);
+static s32 e1000e_led_off_pchlan(struct e1000_hw *hw);
+static void e1000e_clear_hw_cntrs_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank);
+static s32 e1000e_flash_cycle_ich8lan(struct e1000_hw *hw, u32 timeout);
+static s32 e1000e_flash_cycle_init_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_get_phy_info_ife_ich8lan(struct e1000_hw *hw);
+static void e1000e_initialize_hw_bits_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_read_flash_byte_ich8lan(struct e1000_hw *hw,
+ u32 offset, u8 *data);
+static s32 e1000e_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 size, u16 *data);
+static s32 e1000e_read_flash_word_ich8lan(struct e1000_hw *hw,
+ u32 offset, u16 *data);
+static s32 e1000e_retry_write_flash_byte_ich8lan(struct e1000_hw *hw,
+ u32 offset, u8 byte);
+static s32 e1000e_write_flash_byte_ich8lan(struct e1000_hw *hw,
+ u32 offset, u8 data);
+static s32 e1000e_write_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 size, u16 data);
+static s32 e1000e_get_cfg_done_ich8lan(struct e1000_hw *hw);
+static void e1000e_power_down_phy_copper_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_check_for_copper_link_ich8lan(struct e1000_hw *hw);
+static void e1000e_lan_init_done_ich8lan(struct e1000_hw *hw);
+static s32 e1000e_sw_lcd_config_ich8lan(struct e1000_hw *hw);
+
+/* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
+/* Offset 04h HSFSTS */
+union ich8_hws_flash_status {
+ struct ich8_hsfsts {
+ u16 flcdone :1; /* bit 0 Flash Cycle Done */
+ u16 flcerr :1; /* bit 1 Flash Cycle Error */
+ u16 dael :1; /* bit 2 Direct Access error Log */
+ u16 berasesz :2; /* bit 4:3 Sector Erase Size */
+ u16 flcinprog :1; /* bit 5 flash cycle in Progress */
+ u16 reserved1 :2; /* bit 13:6 Reserved */
+ u16 reserved2 :6; /* bit 13:6 Reserved */
+ u16 fldesvalid :1; /* bit 14 Flash Descriptor Valid */
+ u16 flockdn :1; /* bit 15 Flash Config Lock-Down */
+ } hsf_status;
+ u16 regval;
+};
+
+/* ICH GbE Flash Hardware Sequencing Flash control Register bit breakdown */
+/* Offset 06h FLCTL */
+union ich8_hws_flash_ctrl {
+ struct ich8_hsflctl {
+ u16 flcgo :1; /* 0 Flash Cycle Go */
+ u16 flcycle :2; /* 2:1 Flash Cycle */
+ u16 reserved :5; /* 7:3 Reserved */
+ u16 fldbcount :2; /* 9:8 Flash Data Byte Count */
+ u16 flockdn :6; /* 15:10 Reserved */
+ } hsf_ctrl;
+ u16 regval;
+};
+
+/* ICH Flash Region Access Permissions */
+union ich8_hws_flash_regacc {
+ struct ich8_flracc {
+ u32 grra :8; /* 0:7 GbE region Read Access */
+ u32 grwa :8; /* 8:15 GbE region Write Access */
+ u32 gmrag :8; /* 23:16 GbE Master Read Access Grant */
+ u32 gmwag :8; /* 31:24 GbE Master Write Access Grant */
+ } hsf_flregacc;
+ u16 regval;
+};
+
+/**
+ * e1000e_init_phy_params_pchlan - Initialize PHY function pointers
+ * @hw: pointer to the HW structure
+ *
+ * Initialize family-specific PHY parameters and function pointers.
+ **/
+static s32 e1000e_init_phy_params_pchlan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+
+ phy->addr = 1;
+ phy->reset_delay_us = 100;
+
+ phy->ops.acquire = e1000e_acquire_swflag_ich8lan;
+ phy->ops.check_polarity = e1000e_check_polarity_ife;
+ phy->ops.check_reset_block = e1000e_check_reset_block_ich8lan;
+#if 0
+ phy->ops.force_speed_duplex = e1000e_phy_force_speed_duplex_ife;
+#endif
+#if 0
+ phy->ops.get_cable_length = e1000e_get_cable_length_igp_2;
+#endif
+ phy->ops.get_cfg_done = e1000e_get_cfg_done_ich8lan;
+ phy->ops.get_info = e1000e_get_phy_info_ich8lan;
+ phy->ops.read_reg = e1000e_read_phy_reg_hv;
+ phy->ops.read_reg_locked = e1000e_read_phy_reg_hv_locked;
+ phy->ops.release = e1000e_release_swflag_ich8lan;
+ phy->ops.reset = e1000e_phy_hw_reset_ich8lan;
+ phy->ops.set_d0_lplu_state = e1000e_set_lplu_state_pchlan;
+ phy->ops.set_d3_lplu_state = e1000e_set_lplu_state_pchlan;
+ phy->ops.write_reg = e1000e_write_phy_reg_hv;
+ phy->ops.write_reg_locked = e1000e_write_phy_reg_hv_locked;
+ phy->ops.power_up = e1000e_power_up_phy_copper;
+ phy->ops.power_down = e1000e_power_down_phy_copper_ich8lan;
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+
+ phy->id = e1000_phy_unknown;
+ e1000e_get_phy_id(hw);
+ phy->type = e1000e_get_phy_type_from_id(phy->id);
+
+ if (phy->type == e1000_phy_82577) {
+ phy->ops.check_polarity = e1000e_check_polarity_82577;
+#if 0
+ phy->ops.force_speed_duplex =
+ e1000e_phy_force_speed_duplex_82577;
+#endif
+#if 0
+ phy->ops.get_cable_length = e1000e_get_cable_length_82577;
+#endif
+ phy->ops.get_info = e1000e_get_phy_info_82577;
+ phy->ops.commit = e1000e_phy_sw_reset;
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_init_phy_params_ich8lan - Initialize PHY function pointers
+ * @hw: pointer to the HW structure
+ *
+ * Initialize family-specific PHY parameters and function pointers.
+ **/
+static s32 e1000e_init_phy_params_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+ u16 i = 0;
+
+ phy->addr = 1;
+ phy->reset_delay_us = 100;
+
+ phy->ops.acquire = e1000e_acquire_swflag_ich8lan;
+ phy->ops.check_polarity = e1000e_check_polarity_ife;
+ phy->ops.check_reset_block = e1000e_check_reset_block_ich8lan;
+#if 0
+ phy->ops.force_speed_duplex = e1000e_phy_force_speed_duplex_ife;
+#endif
+#if 0
+ phy->ops.get_cable_length = e1000e_get_cable_length_igp_2;
+#endif
+ phy->ops.get_cfg_done = e1000e_get_cfg_done_ich8lan;
+ phy->ops.get_info = e1000e_get_phy_info_ich8lan;
+ phy->ops.read_reg = e1000e_read_phy_reg_igp;
+ phy->ops.release = e1000e_release_swflag_ich8lan;
+ phy->ops.reset = e1000e_phy_hw_reset_ich8lan;
+ phy->ops.set_d0_lplu_state = e1000e_set_d0_lplu_state_ich8lan;
+ phy->ops.set_d3_lplu_state = e1000e_set_d3_lplu_state_ich8lan;
+ phy->ops.write_reg = e1000e_write_phy_reg_igp;
+ phy->ops.power_up = e1000e_power_up_phy_copper;
+ phy->ops.power_down = e1000e_power_down_phy_copper_ich8lan;
+
+ /*
+ * We may need to do this twice - once for IGP and if that fails,
+ * we'll set BM func pointers and try again
+ */
+ ret_val = e1000e_determine_phy_address(hw);
+ if (ret_val) {
+ phy->ops.write_reg = e1000e_write_phy_reg_bm;
+ phy->ops.read_reg = e1000e_read_phy_reg_bm;
+ ret_val = e1000e_determine_phy_address(hw);
+ if (ret_val) {
+ DBG("Cannot determine PHY addr. Erroring out\n");
+ goto out;
+ }
+ }
+
+ phy->id = 0;
+ while ((e1000_phy_unknown == e1000e_get_phy_type_from_id(phy->id)) &&
+ (i++ < 100)) {
+ msleep(1);
+ ret_val = e1000e_get_phy_id(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ /* Verify phy id */
+ switch (phy->id) {
+ case IGP03E1000_E_PHY_ID:
+ phy->type = e1000_phy_igp_3;
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ phy->ops.read_reg_locked = e1000e_read_phy_reg_igp_locked;
+ phy->ops.write_reg_locked = e1000e_write_phy_reg_igp_locked;
+ break;
+ case IFE_E_PHY_ID:
+ case IFE_PLUS_E_PHY_ID:
+ case IFE_C_E_PHY_ID:
+ phy->type = e1000_phy_ife;
+ phy->autoneg_mask = E1000_ALL_NOT_GIG;
+ break;
+ case BME1000_E_PHY_ID:
+ phy->type = e1000_phy_bm;
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ phy->ops.read_reg = e1000e_read_phy_reg_bm;
+ phy->ops.write_reg = e1000e_write_phy_reg_bm;
+ phy->ops.commit = e1000e_phy_sw_reset;
+ break;
+ default:
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_init_nvm_params_ich8lan - Initialize NVM function pointers
+ * @hw: pointer to the HW structure
+ *
+ * Initialize family-specific NVM parameters and function
+ * pointers.
+ **/
+static s32 e1000e_init_nvm_params_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ u32 gfpreg, sector_base_addr, sector_end_addr;
+ s32 ret_val = E1000_SUCCESS;
+ u16 i;
+
+ /* Can't read flash registers if the register set isn't mapped. */
+ if (!hw->flash_address) {
+ e_dbg("ERROR: Flash registers not mapped\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ nvm->type = e1000_nvm_flash_sw;
+
+ gfpreg = er32flash(ICH_FLASH_GFPREG);
+
+ /*
+ * sector_X_addr is a "sector"-aligned address (4096 bytes)
+ * Add 1 to sector_end_addr since this sector is included in
+ * the overall size.
+ */
+ sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK;
+ sector_end_addr = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK) + 1;
+
+ /* flash_base_addr is byte-aligned */
+ nvm->flash_base_addr = sector_base_addr << FLASH_SECTOR_ADDR_SHIFT;
+
+ /*
+ * find total size of the NVM, then cut in half since the total
+ * size represents two separate NVM banks.
+ */
+ nvm->flash_bank_size = (sector_end_addr - sector_base_addr)
+ << FLASH_SECTOR_ADDR_SHIFT;
+ nvm->flash_bank_size /= 2;
+ /* Adjust to word count */
+ nvm->flash_bank_size /= sizeof(u16);
+
+ nvm->word_size = E1000_ICH8_SHADOW_RAM_WORDS;
+
+ /* Clear shadow ram */
+ for (i = 0; i < nvm->word_size; i++) {
+ dev_spec->shadow_ram[i].modified = false;
+ dev_spec->shadow_ram[i].value = 0xFFFF;
+ }
+
+ /* Function Pointers */
+ nvm->ops.acquire = e1000e_acquire_nvm_ich8lan;
+ nvm->ops.release = e1000e_release_nvm_ich8lan;
+ nvm->ops.read = e1000e_read_nvm_ich8lan;
+ nvm->ops.update = e1000e_update_nvm_checksum_ich8lan;
+ nvm->ops.valid_led_default = e1000e_valid_led_default_ich8lan;
+ nvm->ops.validate = e1000e_validate_nvm_checksum_ich8lan;
+ nvm->ops.write = e1000e_write_nvm_ich8lan;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_init_mac_params_ich8lan - Initialize MAC function pointers
+ * @hw: pointer to the HW structure
+ *
+ * Initialize family-specific MAC parameters and function
+ * pointers.
+ **/
+static s32 e1000e_init_mac_params_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+
+ /* Set media type function pointer */
+ hw->phy.media_type = e1000_media_type_copper;
+
+ /* Set mta register count */
+ mac->mta_reg_count = 32;
+ /* Set rar entry count */
+ mac->rar_entry_count = E1000_ICH_RAR_ENTRIES;
+ if (mac->type == e1000_ich8lan)
+ mac->rar_entry_count--;
+ /* Set if part includes ASF firmware */
+ mac->asf_firmware_present = true;
+ /* Set if manageability features are enabled. */
+ mac->arc_subsystem_valid = true;
+
+ /* Function pointers */
+
+ /* bus type/speed/width */
+ mac->ops.get_bus_info = e1000e_get_bus_info_ich8lan;
+ /* function id */
+ mac->ops.set_lan_id = e1000e_set_lan_id_single_port;
+ /* reset */
+ mac->ops.reset_hw = e1000e_reset_hw_ich8lan;
+ /* hw initialization */
+ mac->ops.init_hw = e1000e_init_hw_ich8lan;
+ /* link setup */
+ mac->ops.setup_link = e1000e_setup_link_ich8lan;
+ /* physical interface setup */
+ mac->ops.setup_physical_interface = e1000e_setup_copper_link_ich8lan;
+ /* check for link */
+ mac->ops.check_for_link = e1000e_check_for_copper_link_ich8lan;
+ /* check management mode */
+ mac->ops.check_mng_mode = e1000e_check_mng_mode_ich8lan;
+ /* link info */
+ mac->ops.get_link_up_info = e1000e_get_link_up_info_ich8lan;
+ /* multicast address update */
+ mac->ops.update_mc_addr_list = e1000e_update_mc_addr_list_generic;
+ /* setting MTA */
+ mac->ops.mta_set = e1000e_mta_set_generic;
+ /* clear hardware counters */
+ mac->ops.clear_hw_cntrs = e1000e_clear_hw_cntrs_ich8lan;
+
+ /* LED operations */
+ switch (mac->type) {
+ case e1000_ich8lan:
+ case e1000_ich9lan:
+ case e1000_ich10lan:
+ /* ID LED init */
+ mac->ops.id_led_init = e1000e_id_led_init;
+ /* blink LED */
+ mac->ops.blink_led = e1000e_blink_led;
+ /* setup LED */
+ mac->ops.setup_led = e1000e_setup_led_generic;
+ /* cleanup LED */
+ mac->ops.cleanup_led = e1000e_cleanup_led_ich8lan;
+ /* turn on/off LED */
+ mac->ops.led_on = e1000e_led_on_ich8lan;
+ mac->ops.led_off = e1000e_led_off_ich8lan;
+ break;
+ case e1000_pchlan:
+ /* ID LED init */
+ mac->ops.id_led_init = e1000e_id_led_init_pchlan;
+ /* setup LED */
+ mac->ops.setup_led = e1000e_setup_led_pchlan;
+ /* cleanup LED */
+ mac->ops.cleanup_led = e1000e_cleanup_led_pchlan;
+ /* turn on/off LED */
+ mac->ops.led_on = e1000e_led_on_pchlan;
+ mac->ops.led_off = e1000e_led_off_pchlan;
+ break;
+ default:
+ break;
+ }
+
+ /* Enable PCS Lock-loss workaround for ICH8 */
+ if (mac->type == e1000_ich8lan)
+ e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw, true);
+
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_check_for_copper_link_ich8lan - Check for link (Copper)
+ * @hw: pointer to the HW structure
+ *
+ * Checks to see of the link status of the hardware has changed. If a
+ * change in link status has been detected, then we read the PHY registers
+ * to get the current speed/duplex if link exists.
+ **/
+static s32 e1000e_check_for_copper_link_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+ bool link;
+
+ /*
+ * We only want to go out to the PHY registers to see if Auto-Neg
+ * has completed and/or if our link status has changed. The
+ * get_link_status flag is set upon receiving a Link Status
+ * Change or Rx Sequence Error interrupt.
+ */
+ if (!mac->get_link_status) {
+ ret_val = E1000_SUCCESS;
+ goto out;
+ }
+
+ /*
+ * First we want to see if the MII Status Register reports
+ * link. If so, then we want to get the current speed/duplex
+ * of the PHY.
+ */
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ goto out;
+
+ if (hw->mac.type == e1000_pchlan) {
+ ret_val = e1000e_k1_gig_workaround_hv(hw, link);
+ if (ret_val)
+ goto out;
+ }
+
+ if (!link)
+ goto out; /* No link detected */
+
+ mac->get_link_status = false;
+
+ if (hw->phy.type == e1000_phy_82578) {
+ ret_val = e1000e_link_stall_workaround_hv(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ /*
+ * Check if there was DownShift, must be checked
+ * immediately after link-up
+ */
+ e1000e_check_downshift(hw);
+
+ /*
+ * If we are forcing speed/duplex, then we simply return since
+ * we have already determined whether we have link or not.
+ */
+ if (!mac->autoneg) {
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ /*
+ * Auto-Neg is enabled. Auto Speed Detection takes care
+ * of MAC speed/duplex configuration. So we only need to
+ * configure Collision Distance in the MAC.
+ */
+ e1000e_config_collision_dist(hw);
+
+ /*
+ * Configure Flow Control now that Auto-Neg has completed.
+ * First, we need to restore the desired flow control
+ * settings because we may have had to re-autoneg with a
+ * different link partner.
+ */
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ if (ret_val)
+ e_dbg("Error configuring flow control\n");
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_init_function_pointers_ich8lan - Initialize ICH8 function pointers
+ * @hw: pointer to the HW structure
+ *
+ * Initialize family-specific function pointers for PHY, MAC, and NVM.
+ **/
+void e1000e_init_function_pointers_ich8lan(struct e1000_hw *hw)
+{
+ e1000e_init_mac_ops_generic(hw);
+ e1000e_init_nvm_ops_generic(hw);
+ hw->mac.ops.init_params = e1000e_init_mac_params_ich8lan;
+ hw->nvm.ops.init_params = e1000e_init_nvm_params_ich8lan;
+ switch (hw->mac.type) {
+ case e1000_ich8lan:
+ case e1000_ich9lan:
+ case e1000_ich10lan:
+ hw->phy.ops.init_params = e1000e_init_phy_params_ich8lan;
+ break;
+ case e1000_pchlan:
+ hw->phy.ops.init_params = e1000e_init_phy_params_pchlan;
+ break;
+ default:
+ break;
+ }
+}
+
+#if 0
+static DEFINE_MUTEX(nvm_mutex);
+#endif
+
+/**
+ * e1000e_acquire_nvm_ich8lan - Acquire NVM mutex
+ * @hw: pointer to the HW structure
+ *
+ * Acquires the mutex for performing NVM operations.
+ **/
+static s32 e1000e_acquire_nvm_ich8lan(struct e1000_hw *hw __unused)
+{
+#if 0
+ mutex_lock(&nvm_mutex);
+#endif
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_release_nvm_ich8lan - Release NVM mutex
+ * @hw: pointer to the HW structure
+ *
+ * Releases the mutex used while performing NVM operations.
+ **/
+static void e1000e_release_nvm_ich8lan(struct e1000_hw *hw __unused)
+{
+#if 0
+ mutex_unlock(&nvm_mutex);
+#endif
+ return;
+}
+
+#if 0
+static DEFINE_MUTEX(swflag_mutex);
+#endif
+
+/**
+ * e1000e_acquire_swflag_ich8lan - Acquire software control flag
+ * @hw: pointer to the HW structure
+ *
+ * Acquires the software control flag for performing PHY and select
+ * MAC CSR accesses.
+ **/
+static s32 e1000e_acquire_swflag_ich8lan(struct e1000_hw *hw)
+{
+ u32 extcnf_ctrl, timeout = PHY_CFG_TIMEOUT;
+ s32 ret_val = E1000_SUCCESS;
+
+#if 0
+ mutex_lock(&swflag_mutex);
+#endif
+
+ while (timeout) {
+ extcnf_ctrl = er32(EXTCNF_CTRL);
+ if (!(extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG))
+ break;
+
+ mdelay(1);
+ timeout--;
+ }
+
+ if (!timeout) {
+ e_dbg("SW/FW/HW has locked the resource for too long.\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ timeout = SW_FLAG_TIMEOUT;
+
+ extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG;
+ ew32(EXTCNF_CTRL, extcnf_ctrl);
+
+ while (timeout) {
+ extcnf_ctrl = er32(EXTCNF_CTRL);
+ if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)
+ break;
+
+ mdelay(1);
+ timeout--;
+ }
+
+ if (!timeout) {
+ e_dbg("Failed to acquire the semaphore.\n");
+ extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
+ ew32(EXTCNF_CTRL, extcnf_ctrl);
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+out:
+#if 0
+ if (ret_val)
+ mutex_unlock(&swflag_mutex);
+#endif
+ return ret_val;
+}
+
+/**
+ * e1000e_release_swflag_ich8lan - Release software control flag
+ * @hw: pointer to the HW structure
+ *
+ * Releases the software control flag for performing PHY and select
+ * MAC CSR accesses.
+ **/
+static void e1000e_release_swflag_ich8lan(struct e1000_hw *hw)
+{
+ u32 extcnf_ctrl;
+
+ extcnf_ctrl = er32(EXTCNF_CTRL);
+ extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
+ ew32(EXTCNF_CTRL, extcnf_ctrl);
+
+#if 0
+ mutex_unlock(&swflag_mutex);
+#endif
+ return;
+}
+
+/**
+ * e1000e_check_mng_mode_ich8lan - Checks management mode
+ * @hw: pointer to the HW structure
+ *
+ * This checks if the adapter has manageability enabled.
+ * This is a function pointer entry point only called by read/write
+ * routines for the PHY and NVM parts.
+ **/
+static bool e1000e_check_mng_mode_ich8lan(struct e1000_hw *hw)
+{
+ u32 fwsm;
+
+ fwsm = er32(FWSM);
+ return (fwsm & E1000_FWSM_MODE_MASK) ==
+ (E1000_ICH_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT);
+}
+/**
+ * e1000e_check_reset_block_ich8lan - Check if PHY reset is blocked
+ * @hw: pointer to the HW structure
+ *
+ * Checks if firmware is blocking the reset of the PHY.
+ * This is a function pointer entry point only called by
+ * reset routines.
+ **/
+static s32 e1000e_check_reset_block_ich8lan(struct e1000_hw *hw)
+{
+ u32 fwsm;
+
+ fwsm = er32(FWSM);
+ return (fwsm & E1000_ICH_FWSM_RSPCIPHY) ? E1000_SUCCESS
+ : E1000_BLK_PHY_RESET;
+}
+
+/**
+ * e1000e_sw_lcd_config_ich8lan - SW-based LCD Configuration
+ * @hw: pointer to the HW structure
+ *
+ * SW should configure the LCD from the NVM extended configuration region
+ * as a workaround for certain parts.
+ **/
+static s32 e1000e_sw_lcd_config_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 i, data, cnf_size, cnf_base_addr, sw_cfg_mask;
+ s32 ret_val;
+ u16 word_addr, reg_data, reg_addr, phy_page = 0;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Initialize the PHY from the NVM on ICH platforms. This
+ * is needed due to an issue where the NVM configuration is
+ * not properly autoloaded after power transitions.
+ * Therefore, after each PHY reset, we will load the
+ * configuration data out of the NVM manually.
+ */
+ if ((hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) ||
+ (hw->mac.type == e1000_pchlan)) {
+ /* Check if SW needs to configure the PHY */
+ if ((hw->device_id == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
+ (hw->device_id == E1000_DEV_ID_ICH8_IGP_M) ||
+ (hw->mac.type == e1000_pchlan))
+ sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
+ else
+ sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
+
+ data = er32(FEXTNVM);
+ if (!(data & sw_cfg_mask))
+ goto out;
+
+ /* Wait for basic configuration completes before proceeding */
+ e1000e_lan_init_done_ich8lan(hw);
+
+ /*
+ * Make sure HW does not configure LCD from PHY
+ * extended configuration before SW configuration
+ */
+ data = er32(EXTCNF_CTRL);
+ if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
+ goto out;
+
+ cnf_size = er32(EXTCNF_SIZE);
+ cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
+ cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
+ if (!cnf_size)
+ goto out;
+
+ cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
+ cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
+
+ if (!(data & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE) &&
+ (hw->mac.type == e1000_pchlan)) {
+ /*
+ * HW configures the SMBus address and LEDs when the
+ * OEM and LCD Write Enable bits are set in the NVM.
+ * When both NVM bits are cleared, SW will configure
+ * them instead.
+ */
+ data = er32(STRAP);
+ data &= E1000_STRAP_SMBUS_ADDRESS_MASK;
+ reg_data = data >> E1000_STRAP_SMBUS_ADDRESS_SHIFT;
+ reg_data |= HV_SMB_ADDR_PEC_EN | HV_SMB_ADDR_VALID;
+ ret_val = e1000e_write_phy_reg_hv_locked(hw, HV_SMB_ADDR,
+ reg_data);
+ if (ret_val)
+ goto out;
+
+ data = er32(LEDCTL);
+ ret_val = e1000e_write_phy_reg_hv_locked(hw,
+ HV_LED_CONFIG,
+ (u16)data);
+ if (ret_val)
+ goto out;
+ }
+
+ /* Configure LCD from extended configuration region. */
+
+ /* cnf_base_addr is in DWORD */
+ word_addr = (u16)(cnf_base_addr << 1);
+
+ for (i = 0; i < cnf_size; i++) {
+ ret_val = e1000e_read_nvm(hw, (word_addr + i * 2), 1,
+ ®_data);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000e_read_nvm(hw, (word_addr + i * 2 + 1),
+ 1, ®_addr);
+ if (ret_val)
+ goto out;
+
+ /* Save off the PHY page for future writes. */
+ if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
+ phy_page = reg_data;
+ continue;
+ }
+
+ reg_addr &= PHY_REG_MASK;
+ reg_addr |= phy_page;
+
+ ret_val = phy->ops.write_reg_locked(hw, (u32)reg_addr,
+ reg_data);
+ if (ret_val)
+ goto out;
+ }
+ }
+
+out:
+ hw->phy.ops.release(hw);
+ return ret_val;
+}
+
+/**
+ * e1000e_k1_gig_workaround_hv - K1 Si workaround
+ * @hw: pointer to the HW structure
+ * @link: link up bool flag
+ *
+ * If K1 is enabled for 1Gbps, the MAC might stall when transitioning
+ * from a lower speed. This workaround disables K1 whenever link is at 1Gig
+ * If link is down, the function will restore the default K1 setting located
+ * in the NVM.
+ **/
+static s32 e1000e_k1_gig_workaround_hv(struct e1000_hw *hw, bool link)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 status_reg = 0;
+ bool k1_enable = hw->dev_spec.ich8lan.nvm_k1_enabled;
+
+ if (hw->mac.type != e1000_pchlan)
+ goto out;
+
+ /* Wrap the whole flow with the sw flag */
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ /* Disable K1 when link is 1Gbps, otherwise use the NVM setting */
+ if (link) {
+ if (hw->phy.type == e1000_phy_82578) {
+ ret_val = hw->phy.ops.read_reg_locked(hw, BM_CS_STATUS,
+ &status_reg);
+ if (ret_val)
+ goto release;
+
+ status_reg &= BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_MASK;
+
+ if (status_reg == (BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_1000))
+ k1_enable = false;
+ }
+
+ if (hw->phy.type == e1000_phy_82577) {
+ ret_val = hw->phy.ops.read_reg_locked(hw, HV_M_STATUS,
+ &status_reg);
+ if (ret_val)
+ goto release;
+
+ status_reg &= HV_M_STATUS_LINK_UP |
+ HV_M_STATUS_AUTONEG_COMPLETE |
+ HV_M_STATUS_SPEED_MASK;
+
+ if (status_reg == (HV_M_STATUS_LINK_UP |
+ HV_M_STATUS_AUTONEG_COMPLETE |
+ HV_M_STATUS_SPEED_1000))
+ k1_enable = false;
+ }
+
+ /* Link stall fix for link up */
+ ret_val = hw->phy.ops.write_reg_locked(hw, PHY_REG(770, 19),
+ 0x0100);
+ if (ret_val)
+ goto release;
+
+ } else {
+ /* Link stall fix for link down */
+ ret_val = hw->phy.ops.write_reg_locked(hw, PHY_REG(770, 19),
+ 0x4100);
+ if (ret_val)
+ goto release;
+ }
+
+ ret_val = e1000e_configure_k1_ich8lan(hw, k1_enable);
+
+release:
+ hw->phy.ops.release(hw);
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_configure_k1_ich8lan - Configure K1 power state
+ * @hw: pointer to the HW structure
+ * @enable: K1 state to configure
+ *
+ * Configure the K1 power state based on the provided parameter.
+ * Assumes semaphore already acquired.
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ **/
+s32 e1000e_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u32 ctrl_reg = 0;
+ u32 ctrl_ext = 0;
+ u32 reg = 0;
+ u16 kmrn_reg = 0;
+
+ ret_val = e1000e_read_kmrn_reg_locked(hw,
+ E1000_KMRNCTRLSTA_K1_CONFIG,
+ &kmrn_reg);
+ if (ret_val)
+ goto out;
+
+ if (k1_enable)
+ kmrn_reg |= E1000_KMRNCTRLSTA_K1_ENABLE;
+ else
+ kmrn_reg &= ~E1000_KMRNCTRLSTA_K1_ENABLE;
+
+ ret_val = e1000e_write_kmrn_reg_locked(hw,
+ E1000_KMRNCTRLSTA_K1_CONFIG,
+ kmrn_reg);
+ if (ret_val)
+ goto out;
+
+ udelay(20);
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_reg = er32(CTRL);
+
+ reg = ctrl_reg & ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
+ reg |= E1000_CTRL_FRCSPD;
+ ew32(CTRL, reg);
+
+ E1000_WRITE_REG(hw,
+ E1000_CTRL_EXT,
+ ctrl_ext | E1000_CTRL_EXT_SPD_BYPS);
+ udelay(20);
+ ew32(CTRL, ctrl_reg);
+ ew32(CTRL_EXT, ctrl_ext);
+ udelay(20);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_oem_bits_config_ich8lan - SW-based LCD Configuration
+ * @hw: pointer to the HW structure
+ * @d0_state: boolean if entering d0 or d3 device state
+ *
+ * SW will configure Gbe Disable and LPLU based on the NVM. The four bits are
+ * collectively called OEM bits. The OEM Write Enable bit and SW Config bit
+ * in NVM determines whether HW should configure LPLU and Gbe Disable.
+ **/
+s32 e1000e_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_state)
+{
+ s32 ret_val = 0;
+ u32 mac_reg;
+ u16 oem_reg;
+
+ if (hw->mac.type != e1000_pchlan)
+ return ret_val;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+
+ mac_reg = er32(EXTCNF_CTRL);
+ if (mac_reg & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE)
+ goto out;
+
+ mac_reg = er32(FEXTNVM);
+ if (!(mac_reg & E1000_FEXTNVM_SW_CONFIG_ICH8M))
+ goto out;
+
+ mac_reg = er32(PHY_CTRL);
+
+ ret_val = hw->phy.ops.read_reg_locked(hw, HV_OEM_BITS, &oem_reg);
+ if (ret_val)
+ goto out;
+
+ oem_reg &= ~(HV_OEM_BITS_GBE_DIS | HV_OEM_BITS_LPLU);
+
+ if (d0_state) {
+ if (mac_reg & E1000_PHY_CTRL_GBE_DISABLE)
+ oem_reg |= HV_OEM_BITS_GBE_DIS;
+
+ if (mac_reg & E1000_PHY_CTRL_D0A_LPLU)
+ oem_reg |= HV_OEM_BITS_LPLU;
+ } else {
+ if (mac_reg & E1000_PHY_CTRL_NOND0A_GBE_DISABLE)
+ oem_reg |= HV_OEM_BITS_GBE_DIS;
+
+ if (mac_reg & E1000_PHY_CTRL_NOND0A_LPLU)
+ oem_reg |= HV_OEM_BITS_LPLU;
+ }
+ /* Restart auto-neg to activate the bits */
+ if (!e1000e_check_reset_block(hw))
+ oem_reg |= HV_OEM_BITS_RESTART_AN;
+ ret_val = hw->phy.ops.write_reg_locked(hw, HV_OEM_BITS, oem_reg);
+
+out:
+ hw->phy.ops.release(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_hv_phy_workarounds_ich8lan - A series of Phy workarounds to be
+ * done after every PHY reset.
+ **/
+static s32 e1000e_hv_phy_workarounds_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ if (hw->mac.type != e1000_pchlan)
+ goto out;
+
+ if (((hw->phy.type == e1000_phy_82577) &&
+ ((hw->phy.revision == 1) || (hw->phy.revision == 2))) ||
+ ((hw->phy.type == e1000_phy_82578) && (hw->phy.revision == 1))) {
+ /* Disable generation of early preamble */
+ ret_val = e1e_wphy(hw, PHY_REG(769, 25), 0x4431);
+ if (ret_val)
+ goto out;
+
+ /* Preamble tuning for SSC */
+ ret_val = e1e_wphy(hw, PHY_REG(770, 16), 0xA204);
+ if (ret_val)
+ goto out;
+ }
+
+ if (hw->phy.type == e1000_phy_82578) {
+ /*
+ * Return registers to default by doing a soft reset then
+ * writing 0x3140 to the control register.
+ */
+ if (hw->phy.revision < 2) {
+ e1000e_phy_sw_reset(hw);
+ ret_val = e1e_wphy(hw, PHY_CONTROL,
+ 0x3140);
+ }
+ }
+
+ /* Select page 0 */
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ hw->phy.addr = 1;
+ ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0);
+ if (ret_val)
+ goto out;
+ hw->phy.ops.release(hw);
+
+ /*
+ * Configure the K1 Si workaround during phy reset assuming there is
+ * link so that it disables K1 if link is in 1Gbps.
+ */
+ ret_val = e1000e_k1_gig_workaround_hv(hw, true);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_lan_init_done_ich8lan - Check for PHY config completion
+ * @hw: pointer to the HW structure
+ *
+ * Check the appropriate indication the MAC has finished configuring the
+ * PHY after a software reset.
+ **/
+static void e1000e_lan_init_done_ich8lan(struct e1000_hw *hw)
+{
+ u32 data, loop = E1000_ICH8_LAN_INIT_TIMEOUT;
+
+ /* Wait for basic configuration completes before proceeding */
+ do {
+ data = er32(STATUS);
+ data &= E1000_STATUS_LAN_INIT_DONE;
+ udelay(100);
+ } while ((!data) && --loop);
+
+ /*
+ * If basic configuration is incomplete before the above loop
+ * count reaches 0, loading the configuration from NVM will
+ * leave the PHY in a bad state possibly resulting in no link.
+ */
+ if (loop == 0)
+ e_dbg("LAN_INIT_DONE not set, increase timeout\n");
+
+ /* Clear the Init Done bit for the next init event */
+ data = er32(STATUS);
+ data &= ~E1000_STATUS_LAN_INIT_DONE;
+ ew32(STATUS, data);
+}
+
+/**
+ * e1000e_phy_hw_reset_ich8lan - Performs a PHY reset
+ * @hw: pointer to the HW structure
+ *
+ * Resets the PHY
+ * This is a function pointer entry point called by drivers
+ * or other shared routines.
+ **/
+static s32 e1000e_phy_hw_reset_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 reg;
+
+ ret_val = e1000e_phy_hw_reset_generic(hw);
+ if (ret_val)
+ goto out;
+
+ /* Allow time for h/w to get to a quiescent state after reset */
+ msleep(10);
+
+ if (hw->mac.type == e1000_pchlan) {
+ ret_val = e1000e_hv_phy_workarounds_ich8lan(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ /* Dummy read to clear the phy wakeup bit after lcd reset */
+ if (hw->mac.type == e1000_pchlan)
+ e1e_rphy(hw, BM_WUC, ®);
+
+ /* Configure the LCD with the extended configuration region in NVM */
+ ret_val = e1000e_sw_lcd_config_ich8lan(hw);
+ if (ret_val)
+ goto out;
+
+ /* Configure the LCD with the OEM bits in NVM */
+ if (hw->mac.type == e1000_pchlan)
+ ret_val = e1000e_oem_bits_config_ich8lan(hw, true);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_get_phy_info_ich8lan - Calls appropriate PHY type get_phy_info
+ * @hw: pointer to the HW structure
+ *
+ * Wrapper for calling the get_phy_info routines for the appropriate phy type.
+ **/
+static s32 e1000e_get_phy_info_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val = -E1000_ERR_PHY_TYPE;
+
+ switch (hw->phy.type) {
+ case e1000_phy_ife:
+ ret_val = e1000e_get_phy_info_ife_ich8lan(hw);
+ break;
+ case e1000_phy_igp_3:
+ case e1000_phy_bm:
+ case e1000_phy_82578:
+ case e1000_phy_82577:
+ ret_val = e1000e_get_phy_info_igp(hw);
+ break;
+ default:
+ break;
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_get_phy_info_ife_ich8lan - Retrieves various IFE PHY states
+ * @hw: pointer to the HW structure
+ *
+ * Populates "phy" structure with various feature states.
+ * This function is only called by other family-specific
+ * routines.
+ **/
+static s32 e1000e_get_phy_info_ife_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link) {
+ e_dbg("Phy info is only valid if link is up\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ ret_val = e1e_rphy(hw, IFE_PHY_SPECIAL_CONTROL, &data);
+ if (ret_val)
+ goto out;
+ phy->polarity_correction = (data & IFE_PSC_AUTO_POLARITY_DISABLE)
+ ? false : true;
+
+ if (phy->polarity_correction) {
+ ret_val = e1000e_check_polarity_ife(hw);
+ if (ret_val)
+ goto out;
+ } else {
+ /* Polarity is forced */
+ phy->cable_polarity = (data & IFE_PSC_FORCE_POLARITY)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+ }
+
+ ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data);
+ if (ret_val)
+ goto out;
+
+ phy->is_mdix = (data & IFE_PMC_MDIX_STATUS) ? true : false;
+
+ /* The following parameters are undefined for 10/100 operation. */
+ phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+ phy->local_rx = e1000_1000t_rx_status_undefined;
+ phy->remote_rx = e1000_1000t_rx_status_undefined;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_set_lplu_state_pchlan - Set Low Power Link Up state
+ * @hw: pointer to the HW structure
+ * @active: true to enable LPLU, false to disable
+ *
+ * Sets the LPLU state according to the active flag. For PCH, if OEM write
+ * bit are disabled in the NVM, writing the LPLU bits in the MAC will not set
+ * the phy speed. This function will manually set the LPLU bit and restart
+ * auto-neg as hw would do. D3 and D0 LPLU will call the same function
+ * since it configures the same bit.
+ **/
+static s32 e1000e_set_lplu_state_pchlan(struct e1000_hw *hw, bool active)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 oem_reg;
+
+ ret_val = e1e_rphy(hw, HV_OEM_BITS, &oem_reg);
+ if (ret_val)
+ goto out;
+
+ if (active)
+ oem_reg |= HV_OEM_BITS_LPLU;
+ else
+ oem_reg &= ~HV_OEM_BITS_LPLU;
+
+ oem_reg |= HV_OEM_BITS_RESTART_AN;
+ ret_val = e1e_wphy(hw, HV_OEM_BITS, oem_reg);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_set_d0_lplu_state_ich8lan - Set Low Power Linkup D0 state
+ * @hw: pointer to the HW structure
+ * @active: true to enable LPLU, false to disable
+ *
+ * Sets the LPLU D0 state according to the active flag. When
+ * activating LPLU this function also disables smart speed
+ * and vice versa. LPLU will not be activated unless the
+ * device autonegotiation advertisement meets standards of
+ * either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * This is a function pointer entry point only called by
+ * PHY setup routines.
+ **/
+static s32 e1000e_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 phy_ctrl;
+ s32 ret_val = E1000_SUCCESS;
+ u16 data;
+
+ if (phy->type == e1000_phy_ife)
+ goto out;
+
+ phy_ctrl = er32(PHY_CTRL);
+
+ if (active) {
+ phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU;
+ ew32(PHY_CTRL, phy_ctrl);
+
+ if (phy->type != e1000_phy_igp_3)
+ goto out;
+
+ /*
+ * Call gig speed drop workaround on LPLU before accessing
+ * any PHY registers
+ */
+ if (hw->mac.type == e1000_ich8lan)
+ e1000e_gig_downshift_workaround_ich8lan(hw);
+
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ ret_val = e1e_rphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ goto out;
+ } else {
+ phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
+ ew32(PHY_CTRL, phy_ctrl);
+
+ if (phy->type != e1000_phy_igp_3)
+ goto out;
+
+ /*
+ * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1e_rphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ goto out;
+ } else if (phy->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1e_rphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ goto out;
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_set_d3_lplu_state_ich8lan - Set Low Power Linkup D3 state
+ * @hw: pointer to the HW structure
+ * @active: true to enable LPLU, false to disable
+ *
+ * Sets the LPLU D3 state according to the active flag. When
+ * activating LPLU this function also disables smart speed
+ * and vice versa. LPLU will not be activated unless the
+ * device autonegotiation advertisement meets standards of
+ * either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * This is a function pointer entry point only called by
+ * PHY setup routines.
+ **/
+static s32 e1000e_set_d3_lplu_state_ich8lan(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 phy_ctrl;
+ s32 ret_val = E1000_SUCCESS;
+ u16 data;
+
+ phy_ctrl = er32(PHY_CTRL);
+
+ if (!active) {
+ phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU;
+ ew32(PHY_CTRL, phy_ctrl);
+
+ if (phy->type != e1000_phy_igp_3)
+ goto out;
+
+ /*
+ * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1e_rphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ goto out;
+ } else if (phy->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1e_rphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ goto out;
+ }
+ } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) ||
+ (phy->autoneg_advertised == E1000_ALL_NOT_GIG) ||
+ (phy->autoneg_advertised == E1000_ALL_10_SPEED)) {
+ phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU;
+ ew32(PHY_CTRL, phy_ctrl);
+
+ if (phy->type != e1000_phy_igp_3)
+ goto out;
+
+ /*
+ * Call gig speed drop workaround on LPLU before accessing
+ * any PHY registers
+ */
+ if (hw->mac.type == e1000_ich8lan)
+ e1000e_gig_downshift_workaround_ich8lan(hw);
+
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ ret_val = e1e_rphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_valid_nvm_bank_detect_ich8lan - finds out the valid bank 0 or 1
+ * @hw: pointer to the HW structure
+ * @bank: pointer to the variable that returns the active bank
+ *
+ * Reads signature byte from the NVM using the flash access registers.
+ * Word 0x13 bits 15:14 = 10b indicate a valid signature for that bank.
+ **/
+static s32 e1000e_valid_nvm_bank_detect_ich8lan(struct e1000_hw *hw, u32 *bank)
+{
+ u32 eecd;
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 bank1_offset = nvm->flash_bank_size * sizeof(u16);
+ u32 act_offset = E1000_ICH_NVM_SIG_WORD * 2 + 1;
+ u8 sig_byte = 0;
+ s32 ret_val = E1000_SUCCESS;
+
+ switch (hw->mac.type) {
+ case e1000_ich8lan:
+ case e1000_ich9lan:
+ eecd = er32(EECD);
+ if ((eecd & E1000_EECD_SEC1VAL_VALID_MASK) ==
+ E1000_EECD_SEC1VAL_VALID_MASK) {
+ if (eecd & E1000_EECD_SEC1VAL)
+ *bank = 1;
+ else
+ *bank = 0;
+
+ goto out;
+ }
+ e_dbg("Unable to determine valid NVM bank via EEC - "
+ "reading flash signature\n");
+ /* fall-thru */
+ default:
+ /* set bank to 0 in case flash read fails */
+ *bank = 0;
+
+ /* Check bank 0 */
+ ret_val = e1000e_read_flash_byte_ich8lan(hw, act_offset,
+ &sig_byte);
+ if (ret_val)
+ goto out;
+ if ((sig_byte & E1000_ICH_NVM_VALID_SIG_MASK) ==
+ E1000_ICH_NVM_SIG_VALUE) {
+ *bank = 0;
+ goto out;
+ }
+
+ /* Check bank 1 */
+ ret_val = e1000e_read_flash_byte_ich8lan(hw, act_offset +
+ bank1_offset,
+ &sig_byte);
+ if (ret_val)
+ goto out;
+ if ((sig_byte & E1000_ICH_NVM_VALID_SIG_MASK) ==
+ E1000_ICH_NVM_SIG_VALUE) {
+ *bank = 1;
+ goto out;
+ }
+
+ e_dbg("ERROR: No valid NVM bank present\n");
+ ret_val = -E1000_ERR_NVM;
+ break;
+ }
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_nvm_ich8lan - Read word(s) from the NVM
+ * @hw: pointer to the HW structure
+ * @offset: The offset (in bytes) of the word(s) to read.
+ * @words: Size of data to read in words
+ * @data: Pointer to the word(s) to read at offset.
+ *
+ * Reads a word(s) from the NVM using the flash access registers.
+ **/
+static s32 e1000e_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ u32 act_offset;
+ s32 ret_val = E1000_SUCCESS;
+ u32 bank = 0;
+ u16 i, word;
+
+ if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) ||
+ (words == 0)) {
+ e_dbg("nvm parameter(s) out of bounds\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+ nvm->ops.acquire(hw);
+
+ ret_val = e1000e_valid_nvm_bank_detect_ich8lan(hw, &bank);
+ if (ret_val != E1000_SUCCESS) {
+ e_dbg("Could not detect valid bank, assuming bank 0\n");
+ bank = 0;
+ }
+
+ act_offset = (bank) ? nvm->flash_bank_size : 0;
+ act_offset += offset;
+
+ ret_val = E1000_SUCCESS;
+ for (i = 0; i < words; i++) {
+ if ((dev_spec->shadow_ram) &&
+ (dev_spec->shadow_ram[offset+i].modified)) {
+ data[i] = dev_spec->shadow_ram[offset+i].value;
+ } else {
+ ret_val = e1000e_read_flash_word_ich8lan(hw,
+ act_offset + i,
+ &word);
+ if (ret_val)
+ break;
+ data[i] = word;
+ }
+ }
+
+ nvm->ops.release(hw);
+
+out:
+ if (ret_val)
+ e_dbg("NVM read error: %d\n", ret_val);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_flash_cycle_init_ich8lan - Initialize flash
+ * @hw: pointer to the HW structure
+ *
+ * This function does initial flash setup so that a new read/write/erase cycle
+ * can be started.
+ **/
+static s32 e1000e_flash_cycle_init_ich8lan(struct e1000_hw *hw)
+{
+ union ich8_hws_flash_status hsfsts;
+ s32 ret_val = -E1000_ERR_NVM;
+ s32 i = 0;
+
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+
+ /* Check if the flash descriptor is valid */
+ if (hsfsts.hsf_status.fldesvalid == 0) {
+ e_dbg("Flash descriptor invalid. "
+ "SW Sequencing must be used.");
+ goto out;
+ }
+
+ /* Clear FCERR and DAEL in hw status by writing 1 */
+ hsfsts.hsf_status.flcerr = 1;
+ hsfsts.hsf_status.dael = 1;
+
+ ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
+
+ /*
+ * Either we should have a hardware SPI cycle in progress
+ * bit to check against, in order to start a new cycle or
+ * FDONE bit should be changed in the hardware so that it
+ * is 1 after hardware reset, which can then be used as an
+ * indication whether a cycle is in progress or has been
+ * completed.
+ */
+
+ if (hsfsts.hsf_status.flcinprog == 0) {
+ /*
+ * There is no cycle running at present,
+ * so we can start a cycle.
+ * Begin by setting Flash Cycle Done.
+ */
+ hsfsts.hsf_status.flcdone = 1;
+ ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
+ ret_val = E1000_SUCCESS;
+ } else {
+ /*
+ * Otherwise poll for sometime so the current
+ * cycle has a chance to end before giving up.
+ */
+ for (i = 0; i < ICH_FLASH_READ_COMMAND_TIMEOUT; i++) {
+ hsfsts.regval = er16flash(
+ ICH_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcinprog == 0) {
+ ret_val = E1000_SUCCESS;
+ break;
+ }
+ udelay(1);
+ }
+ if (ret_val == E1000_SUCCESS) {
+ /*
+ * Successful in waiting for previous cycle to timeout,
+ * now set the Flash Cycle Done.
+ */
+ hsfsts.hsf_status.flcdone = 1;
+ ew16flash(ICH_FLASH_HSFSTS,
+ hsfsts.regval);
+ } else {
+ e_dbg("Flash controller busy, cannot get access");
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_flash_cycle_ich8lan - Starts flash cycle (read/write/erase)
+ * @hw: pointer to the HW structure
+ * @timeout: maximum time to wait for completion
+ *
+ * This function starts a flash cycle and waits for its completion.
+ **/
+static s32 e1000e_flash_cycle_ich8lan(struct e1000_hw *hw, u32 timeout)
+{
+ union ich8_hws_flash_ctrl hsflctl;
+ union ich8_hws_flash_status hsfsts;
+ s32 ret_val = -E1000_ERR_NVM;
+ u32 i = 0;
+
+ /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */
+ hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
+ hsflctl.hsf_ctrl.flcgo = 1;
+ ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
+
+ /* wait till FDONE bit is set to 1 */
+ do {
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcdone == 1)
+ break;
+ udelay(1);
+ } while (i++ < timeout);
+
+ if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0)
+ ret_val = E1000_SUCCESS;
+
+ return ret_val;
+}
+
+/**
+ * e1000e_read_flash_word_ich8lan - Read word from flash
+ * @hw: pointer to the HW structure
+ * @offset: offset to data location
+ * @data: pointer to the location for storing the data
+ *
+ * Reads the flash word at offset into data. Offset is converted
+ * to bytes before read.
+ **/
+static s32 e1000e_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset,
+ u16 *data)
+{
+ s32 ret_val;
+
+ if (!data) {
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+ /* Must convert offset into bytes. */
+ offset <<= 1;
+
+ ret_val = e1000e_read_flash_data_ich8lan(hw, offset, 2, data);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_flash_byte_ich8lan - Read byte from flash
+ * @hw: pointer to the HW structure
+ * @offset: The offset of the byte to read.
+ * @data: Pointer to a byte to store the value read.
+ *
+ * Reads a single byte from the NVM using the flash access registers.
+ **/
+static s32 e1000e_read_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 *data)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 word = 0;
+
+ ret_val = e1000e_read_flash_data_ich8lan(hw, offset, 1, &word);
+ if (ret_val)
+ goto out;
+
+ *data = (u8)word;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_flash_data_ich8lan - Read byte or word from NVM
+ * @hw: pointer to the HW structure
+ * @offset: The offset (in bytes) of the byte or word to read.
+ * @size: Size of data to read, 1=byte 2=word
+ * @data: Pointer to the word to store the value read.
+ *
+ * Reads a byte or word from the NVM using the flash access registers.
+ **/
+static s32 e1000e_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 size, u16 *data)
+{
+ union ich8_hws_flash_status hsfsts;
+ union ich8_hws_flash_ctrl hsflctl;
+ u32 flash_linear_addr;
+ u32 flash_data = 0;
+ s32 ret_val = -E1000_ERR_NVM;
+ u8 count = 0;
+
+ if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK)
+ goto out;
+ flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) +
+ hw->nvm.flash_base_addr;
+
+ do {
+ udelay(1);
+ /* Steps */
+ ret_val = e1000e_flash_cycle_init_ich8lan(hw);
+ if (ret_val != E1000_SUCCESS)
+ break;
+
+ hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
+ /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
+ hsflctl.hsf_ctrl.fldbcount = size - 1;
+ hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ;
+ ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
+
+ ew32flash(ICH_FLASH_FADDR, flash_linear_addr);
+
+ ret_val = e1000e_flash_cycle_ich8lan(hw,
+ ICH_FLASH_READ_COMMAND_TIMEOUT);
+
+ /*
+ * Check if FCERR is set to 1, if set to 1, clear it
+ * and try the whole sequence a few more times, else
+ * read in (shift in) the Flash Data0, the order is
+ * least significant byte first msb to lsb
+ */
+ if (ret_val == E1000_SUCCESS) {
+ flash_data = er32flash(ICH_FLASH_FDATA0);
+ if (size == 1)
+ *data = (u8)(flash_data & 0x000000FF);
+ else if (size == 2)
+ *data = (u16)(flash_data & 0x0000FFFF);
+ break;
+ } else {
+ /*
+ * If we've gotten here, then things are probably
+ * completely hosed, but if the error condition is
+ * detected, it won't hurt to give it another try...
+ * ICH_FLASH_CYCLE_REPEAT_COUNT times.
+ */
+ hsfsts.regval = er16flash(
+ ICH_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcerr == 1) {
+ /* Repeat for some time before giving up. */
+ continue;
+ } else if (hsfsts.hsf_status.flcdone == 0) {
+ e_dbg("Timeout error - flash cycle "
+ "did not complete.");
+ break;
+ }
+ }
+ } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_write_nvm_ich8lan - Write word(s) to the NVM
+ * @hw: pointer to the HW structure
+ * @offset: The offset (in bytes) of the word(s) to write.
+ * @words: Size of data to write in words
+ * @data: Pointer to the word(s) to write at offset.
+ *
+ * Writes a byte or word to the NVM using the flash access registers.
+ **/
+static s32 e1000e_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ s32 ret_val = E1000_SUCCESS;
+ u16 i;
+
+ if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) ||
+ (words == 0)) {
+ e_dbg("nvm parameter(s) out of bounds\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+ nvm->ops.acquire(hw);
+
+ for (i = 0; i < words; i++) {
+ dev_spec->shadow_ram[offset+i].modified = true;
+ dev_spec->shadow_ram[offset+i].value = data[i];
+ }
+
+ nvm->ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_update_nvm_checksum_ich8lan - Update the checksum for NVM
+ * @hw: pointer to the HW structure
+ *
+ * The NVM checksum is updated by calling the generic update_nvm_checksum,
+ * which writes the checksum to the shadow ram. The changes in the shadow
+ * ram are then committed to the EEPROM by processing each bank at a time
+ * checking for the modified bit and writing only the pending changes.
+ * After a successful commit, the shadow ram is cleared and is ready for
+ * future writes.
+ **/
+static s32 e1000e_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ u32 i, act_offset, new_bank_offset, old_bank_offset, bank;
+ s32 ret_val;
+ u16 data;
+
+ ret_val = e1000e_update_nvm_checksum_generic(hw);
+ if (ret_val)
+ goto out;
+
+ if (nvm->type != e1000_nvm_flash_sw)
+ goto out;
+
+ nvm->ops.acquire(hw);
+
+ /*
+ * We're writing to the opposite bank so if we're on bank 1,
+ * write to bank 0 etc. We also need to erase the segment that
+ * is going to be written
+ */
+ ret_val = e1000e_valid_nvm_bank_detect_ich8lan(hw, &bank);
+ if (ret_val != E1000_SUCCESS) {
+ e_dbg("Could not detect valid bank, assuming bank 0\n");
+ bank = 0;
+ }
+
+ if (bank == 0) {
+ new_bank_offset = nvm->flash_bank_size;
+ old_bank_offset = 0;
+ ret_val = e1000e_erase_flash_bank_ich8lan(hw, 1);
+ if (ret_val) {
+ nvm->ops.release(hw);
+ goto out;
+ }
+ } else {
+ old_bank_offset = nvm->flash_bank_size;
+ new_bank_offset = 0;
+ ret_val = e1000e_erase_flash_bank_ich8lan(hw, 0);
+ if (ret_val) {
+ nvm->ops.release(hw);
+ goto out;
+ }
+ }
+
+ for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) {
+ /*
+ * Determine whether to write the value stored
+ * in the other NVM bank or a modified value stored
+ * in the shadow RAM
+ */
+ if (dev_spec->shadow_ram[i].modified) {
+ data = dev_spec->shadow_ram[i].value;
+ } else {
+ ret_val = e1000e_read_flash_word_ich8lan(hw, i +
+ old_bank_offset,
+ &data);
+ if (ret_val)
+ break;
+ }
+
+ /*
+ * If the word is 0x13, then make sure the signature bits
+ * (15:14) are 11b until the commit has completed.
+ * This will allow us to write 10b which indicates the
+ * signature is valid. We want to do this after the write
+ * has completed so that we don't mark the segment valid
+ * while the write is still in progress
+ */
+ if (i == E1000_ICH_NVM_SIG_WORD)
+ data |= E1000_ICH_NVM_SIG_MASK;
+
+ /* Convert offset to bytes. */
+ act_offset = (i + new_bank_offset) << 1;
+
+ udelay(100);
+ /* Write the bytes to the new bank. */
+ ret_val = e1000e_retry_write_flash_byte_ich8lan(hw,
+ act_offset,
+ (u8)data);
+ if (ret_val)
+ break;
+
+ udelay(100);
+ ret_val = e1000e_retry_write_flash_byte_ich8lan(hw,
+ act_offset + 1,
+ (u8)(data >> 8));
+ if (ret_val)
+ break;
+ }
+
+ /*
+ * Don't bother writing the segment valid bits if sector
+ * programming failed.
+ */
+ if (ret_val) {
+ e_dbg("Flash commit failed.\n");
+ nvm->ops.release(hw);
+ goto out;
+ }
+
+ /*
+ * Finally validate the new segment by setting bit 15:14
+ * to 10b in word 0x13 , this can be done without an
+ * erase as well since these bits are 11 to start with
+ * and we need to change bit 14 to 0b
+ */
+ act_offset = new_bank_offset + E1000_ICH_NVM_SIG_WORD;
+ ret_val = e1000e_read_flash_word_ich8lan(hw, act_offset, &data);
+ if (ret_val) {
+ nvm->ops.release(hw);
+ goto out;
+ }
+
+ data &= 0xBFFF;
+ ret_val = e1000e_retry_write_flash_byte_ich8lan(hw,
+ act_offset * 2 + 1,
+ (u8)(data >> 8));
+ if (ret_val) {
+ nvm->ops.release(hw);
+ goto out;
+ }
+
+ /*
+ * And invalidate the previously valid segment by setting
+ * its signature word (0x13) high_byte to 0b. This can be
+ * done without an erase because flash erase sets all bits
+ * to 1's. We can write 1's to 0's without an erase
+ */
+ act_offset = (old_bank_offset + E1000_ICH_NVM_SIG_WORD) * 2 + 1;
+ ret_val = e1000e_retry_write_flash_byte_ich8lan(hw, act_offset, 0);
+ if (ret_val) {
+ nvm->ops.release(hw);
+ goto out;
+ }
+
+ /* Great! Everything worked, we can now clear the cached entries. */
+ for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) {
+ dev_spec->shadow_ram[i].modified = false;
+ dev_spec->shadow_ram[i].value = 0xFFFF;
+ }
+
+ nvm->ops.release(hw);
+
+ /*
+ * Reload the EEPROM, or else modifications will not appear
+ * until after the next adapter reset.
+ */
+ nvm->ops.reload(hw);
+ msleep(10);
+
+out:
+ if (ret_val)
+ e_dbg("NVM update error: %d\n", ret_val);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_validate_nvm_checksum_ich8lan - Validate EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Check to see if checksum needs to be fixed by reading bit 6 in word 0x19.
+ * If the bit is 0, that the EEPROM had been modified, but the checksum was not
+ * calculated, in which case we need to calculate the checksum and set bit 6.
+ **/
+static s32 e1000e_validate_nvm_checksum_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 data;
+
+ /*
+ * Read 0x19 and check bit 6. If this bit is 0, the checksum
+ * needs to be fixed. This bit is an indication that the NVM
+ * was prepared by OEM software and did not calculate the
+ * checksum...a likely scenario.
+ */
+ ret_val = e1000e_read_nvm(hw, 0x19, 1, &data);
+ if (ret_val)
+ goto out;
+
+ if ((data & 0x40) == 0) {
+ data |= 0x40;
+ ret_val = e1000e_write_nvm(hw, 0x19, 1, &data);
+ if (ret_val)
+ goto out;
+ ret_val = e1000e_update_nvm_checksum(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_validate_nvm_checksum_generic(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_write_flash_data_ich8lan - Writes bytes to the NVM
+ * @hw: pointer to the HW structure
+ * @offset: The offset (in bytes) of the byte/word to read.
+ * @size: Size of data to read, 1=byte 2=word
+ * @data: The byte(s) to write to the NVM.
+ *
+ * Writes one/two bytes to the NVM using the flash access registers.
+ **/
+static s32 e1000e_write_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 size, u16 data)
+{
+ union ich8_hws_flash_status hsfsts;
+ union ich8_hws_flash_ctrl hsflctl;
+ u32 flash_linear_addr;
+ u32 flash_data = 0;
+ s32 ret_val = -E1000_ERR_NVM;
+ u8 count = 0;
+
+ if (size < 1 || size > 2 || data > size * 0xff ||
+ offset > ICH_FLASH_LINEAR_ADDR_MASK)
+ goto out;
+
+ flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) +
+ hw->nvm.flash_base_addr;
+
+ do {
+ udelay(1);
+ /* Steps */
+ ret_val = e1000e_flash_cycle_init_ich8lan(hw);
+ if (ret_val != E1000_SUCCESS)
+ break;
+
+ hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
+ /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
+ hsflctl.hsf_ctrl.fldbcount = size - 1;
+ hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE;
+ ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
+
+ ew32flash(ICH_FLASH_FADDR, flash_linear_addr);
+
+ if (size == 1)
+ flash_data = (u32)data & 0x00FF;
+ else
+ flash_data = (u32)data;
+
+ ew32flash(ICH_FLASH_FDATA0, flash_data);
+
+ /*
+ * check if FCERR is set to 1 , if set to 1, clear it
+ * and try the whole sequence a few more times else done
+ */
+ ret_val = e1000e_flash_cycle_ich8lan(hw,
+ ICH_FLASH_WRITE_COMMAND_TIMEOUT);
+ if (ret_val == E1000_SUCCESS)
+ break;
+
+ /*
+ * If we're here, then things are most likely
+ * completely hosed, but if the error condition
+ * is detected, it won't hurt to give it another
+ * try...ICH_FLASH_CYCLE_REPEAT_COUNT times.
+ */
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcerr == 1) {
+ /* Repeat for some time before giving up. */
+ continue;
+ } else if (hsfsts.hsf_status.flcdone == 0) {
+ e_dbg("Timeout error - flash cycle "
+ "did not complete.");
+ break;
+ }
+ } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_write_flash_byte_ich8lan - Write a single byte to NVM
+ * @hw: pointer to the HW structure
+ * @offset: The index of the byte to read.
+ * @data: The byte to write to the NVM.
+ *
+ * Writes a single byte to the NVM using the flash access registers.
+ **/
+static s32 e1000e_write_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 data)
+{
+ u16 word = (u16)data;
+
+ return e1000e_write_flash_data_ich8lan(hw, offset, 1, word);
+}
+
+/**
+ * e1000e_retry_write_flash_byte_ich8lan - Writes a single byte to NVM
+ * @hw: pointer to the HW structure
+ * @offset: The offset of the byte to write.
+ * @byte: The byte to write to the NVM.
+ *
+ * Writes a single byte to the NVM using the flash access registers.
+ * Goes through a retry algorithm before giving up.
+ **/
+static s32 e1000e_retry_write_flash_byte_ich8lan(struct e1000_hw *hw,
+ u32 offset, u8 byte)
+{
+ s32 ret_val;
+ u16 program_retries;
+
+ ret_val = e1000e_write_flash_byte_ich8lan(hw, offset, byte);
+ if (ret_val == E1000_SUCCESS)
+ goto out;
+
+ for (program_retries = 0; program_retries < 100; program_retries++) {
+ e_dbg("Retrying Byte %2.2X at offset %u\n", byte, offset);
+ udelay(100);
+ ret_val = e1000e_write_flash_byte_ich8lan(hw, offset, byte);
+ if (ret_val == E1000_SUCCESS)
+ break;
+ }
+ if (program_retries == 100) {
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_erase_flash_bank_ich8lan - Erase a bank (4k) from NVM
+ * @hw: pointer to the HW structure
+ * @bank: 0 for first bank, 1 for second bank, etc.
+ *
+ * Erases the bank specified. Each bank is a 4k block. Banks are 0 based.
+ * bank N is 4096 * N + flash_reg_addr.
+ **/
+static s32 e1000e_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ union ich8_hws_flash_status hsfsts;
+ union ich8_hws_flash_ctrl hsflctl;
+ u32 flash_linear_addr;
+ /* bank size is in 16bit words - adjust to bytes */
+ u32 flash_bank_size = nvm->flash_bank_size * 2;
+ s32 ret_val = E1000_SUCCESS;
+ s32 count = 0;
+ s32 j, iteration, sector_size;
+
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+
+ /*
+ * Determine HW Sector size: Read BERASE bits of hw flash status
+ * register
+ * 00: The Hw sector is 256 bytes, hence we need to erase 16
+ * consecutive sectors. The start index for the nth Hw sector
+ * can be calculated as = bank * 4096 + n * 256
+ * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector.
+ * The start index for the nth Hw sector can be calculated
+ * as = bank * 4096
+ * 10: The Hw sector is 8K bytes, nth sector = bank * 8192
+ * (ich9 only, otherwise error condition)
+ * 11: The Hw sector is 64K bytes, nth sector = bank * 65536
+ */
+ switch (hsfsts.hsf_status.berasesz) {
+ case 0:
+ /* Hw sector size 256 */
+ sector_size = ICH_FLASH_SEG_SIZE_256;
+ iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_256;
+ break;
+ case 1:
+ sector_size = ICH_FLASH_SEG_SIZE_4K;
+ iteration = 1;
+ break;
+ case 2:
+ sector_size = ICH_FLASH_SEG_SIZE_8K;
+ iteration = 1;
+ break;
+ case 3:
+ sector_size = ICH_FLASH_SEG_SIZE_64K;
+ iteration = 1;
+ break;
+ default:
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+ /* Start with the base address, then add the sector offset. */
+ flash_linear_addr = hw->nvm.flash_base_addr;
+ flash_linear_addr += (bank) ? flash_bank_size : 0;
+
+ for (j = 0; j < iteration ; j++) {
+ do {
+ /* Steps */
+ ret_val = e1000e_flash_cycle_init_ich8lan(hw);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Write a value 11 (block Erase) in Flash
+ * Cycle field in hw flash control
+ */
+ hsflctl.regval = er16flash(
+ ICH_FLASH_HSFCTL);
+ hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE;
+ ew16flash(ICH_FLASH_HSFCTL,
+ hsflctl.regval);
+
+ /*
+ * Write the last 24 bits of an index within the
+ * block into Flash Linear address field in Flash
+ * Address.
+ */
+ flash_linear_addr += (j * sector_size);
+ ew32flash(ICH_FLASH_FADDR,
+ flash_linear_addr);
+
+ ret_val = e1000e_flash_cycle_ich8lan(hw,
+ ICH_FLASH_ERASE_COMMAND_TIMEOUT);
+ if (ret_val == E1000_SUCCESS)
+ break;
+
+ /*
+ * Check if FCERR is set to 1. If 1,
+ * clear it and try the whole sequence
+ * a few more times else Done
+ */
+ hsfsts.regval = er16flash(
+ ICH_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcerr == 1)
+ /* repeat for some time before giving up */
+ continue;
+ else if (hsfsts.hsf_status.flcdone == 0)
+ goto out;
+ } while (++count < ICH_FLASH_CYCLE_REPEAT_COUNT);
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_valid_led_default_ich8lan - Set the default LED settings
+ * @hw: pointer to the HW structure
+ * @data: Pointer to the LED settings
+ *
+ * Reads the LED default settings from the NVM to data. If the NVM LED
+ * settings is all 0's or F's, set the LED default to a valid LED default
+ * setting.
+ **/
+static s32 e1000e_valid_led_default_ich8lan(struct e1000_hw *hw, u16 *data)
+{
+ s32 ret_val;
+
+ ret_val = e1000e_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ goto out;
+ }
+
+ if (*data == ID_LED_RESERVED_0000 ||
+ *data == ID_LED_RESERVED_FFFF)
+ *data = ID_LED_DEFAULT_ICH8LAN;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_id_led_init_pchlan - store LED configurations
+ * @hw: pointer to the HW structure
+ *
+ * PCH does not control LEDs via the LEDCTL register, rather it uses
+ * the PHY LED configuration register.
+ *
+ * PCH also does not have an "always on" or "always off" mode which
+ * complicates the ID feature. Instead of using the "on" mode to indicate
+ * in ledctl_mode2 the LEDs to use for ID (see e1000e_id_led_init()),
+ * use "link_up" mode. The LEDs will still ID on request if there is no
+ * link based on logic in e1000e_led_[on|off]_pchlan().
+ **/
+static s32 e1000e_id_led_init_pchlan(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+ const u32 ledctl_on = E1000_LEDCTL_MODE_LINK_UP;
+ const u32 ledctl_off = E1000_LEDCTL_MODE_LINK_UP | E1000_PHY_LED0_IVRT;
+ u16 data, i, temp, shift;
+
+ /* Get default ID LED modes */
+ ret_val = hw->nvm.ops.valid_led_default(hw, &data);
+ if (ret_val)
+ goto out;
+
+ mac->ledctl_default = er32(LEDCTL);
+ mac->ledctl_mode1 = mac->ledctl_default;
+ mac->ledctl_mode2 = mac->ledctl_default;
+
+ for (i = 0; i < 4; i++) {
+ temp = (data >> (i << 2)) & E1000_LEDCTL_LED0_MODE_MASK;
+ shift = (i * 5);
+ switch (temp) {
+ case ID_LED_ON1_DEF2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_ON1_OFF2:
+ mac->ledctl_mode1 &= ~(E1000_PHY_LED0_MASK << shift);
+ mac->ledctl_mode1 |= (ledctl_on << shift);
+ break;
+ case ID_LED_OFF1_DEF2:
+ case ID_LED_OFF1_ON2:
+ case ID_LED_OFF1_OFF2:
+ mac->ledctl_mode1 &= ~(E1000_PHY_LED0_MASK << shift);
+ mac->ledctl_mode1 |= (ledctl_off << shift);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ switch (temp) {
+ case ID_LED_DEF1_ON2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_OFF1_ON2:
+ mac->ledctl_mode2 &= ~(E1000_PHY_LED0_MASK << shift);
+ mac->ledctl_mode2 |= (ledctl_on << shift);
+ break;
+ case ID_LED_DEF1_OFF2:
+ case ID_LED_ON1_OFF2:
+ case ID_LED_OFF1_OFF2:
+ mac->ledctl_mode2 &= ~(E1000_PHY_LED0_MASK << shift);
+ mac->ledctl_mode2 |= (ledctl_off << shift);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_get_bus_info_ich8lan - Get/Set the bus type and width
+ * @hw: pointer to the HW structure
+ *
+ * ICH8 use the PCI Express bus, but does not contain a PCI Express Capability
+ * register, so the the bus width is hard coded.
+ **/
+static s32 e1000e_get_bus_info_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_bus_info *bus = &hw->bus;
+ s32 ret_val;
+
+ ret_val = e1000e_get_bus_info_pcie(hw);
+
+ /*
+ * ICH devices are "PCI Express"-ish. They have
+ * a configuration space, but do not contain
+ * PCI Express Capability registers, so bus width
+ * must be hardcoded.
+ */
+ if (bus->width == e1000_bus_width_unknown)
+ bus->width = e1000_bus_width_pcie_x1;
+
+ return ret_val;
+}
+
+/**
+ * e1000e_reset_hw_ich8lan - Reset the hardware
+ * @hw: pointer to the HW structure
+ *
+ * Does a full reset of the hardware which includes a reset of the PHY and
+ * MAC.
+ **/
+static s32 e1000e_reset_hw_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ u16 reg;
+ u32 ctrl, icr, kab;
+ s32 ret_val;
+
+ /*
+ * Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ ret_val = e1000e_disable_pcie_master(hw);
+ if (ret_val)
+ e_dbg("PCI-E Master disable polling has failed.\n");
+
+ e_dbg("Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ /*
+ * Disable the Transmit and Receive units. Then delay to allow
+ * any pending transactions to complete before we hit the MAC
+ * with the global reset.
+ */
+ ew32(RCTL, 0);
+ ew32(TCTL, E1000_TCTL_PSP);
+ e1e_flush();
+
+ msleep(10);
+
+ /* Workaround for ICH8 bit corruption issue in FIFO memory */
+ if (hw->mac.type == e1000_ich8lan) {
+ /* Set Tx and Rx buffer allocation to 8k apiece. */
+ ew32(PBA, E1000_PBA_8K);
+ /* Set Packet Buffer Size to 16k. */
+ ew32(PBS, E1000_PBS_16K);
+ }
+
+ if (hw->mac.type == e1000_pchlan) {
+ /* Save the NVM K1 bit setting*/
+ ret_val = e1000e_read_nvm(hw, E1000_NVM_K1_CONFIG, 1, ®);
+ if (ret_val)
+ return ret_val;
+
+ if (reg & E1000_NVM_K1_ENABLE)
+ dev_spec->nvm_k1_enabled = true;
+ else
+ dev_spec->nvm_k1_enabled = false;
+ }
+
+ ctrl = er32(CTRL);
+
+ if (!e1000e_check_reset_block(hw) && !hw->phy.reset_disable) {
+ /* Clear PHY Reset Asserted bit */
+ if (hw->mac.type >= e1000_pchlan) {
+ u32 status = er32(STATUS);
+ ew32(STATUS, status &
+ ~E1000_STATUS_PHYRA);
+ }
+
+ /*
+ * PHY HW reset requires MAC CORE reset at the same
+ * time to make sure the interface between MAC and the
+ * external PHY is reset.
+ */
+ ctrl |= E1000_CTRL_PHY_RST;
+ }
+ ret_val = e1000e_acquire_swflag_ich8lan(hw);
+ e_dbg("Issuing a global reset to ich8lan\n");
+ ew32(CTRL, (ctrl | E1000_CTRL_RST));
+ msleep(20);
+
+ if (!ret_val)
+ e1000e_release_swflag_ich8lan(hw);
+
+ if (ctrl & E1000_CTRL_PHY_RST)
+ ret_val = hw->phy.ops.get_cfg_done(hw);
+
+ if (hw->mac.type >= e1000_ich10lan) {
+ e1000e_lan_init_done_ich8lan(hw);
+ } else {
+ ret_val = e1000e_get_auto_rd_done(hw);
+ if (ret_val) {
+ /*
+ * When auto config read does not complete, do not
+ * return with an error. This can happen in situations
+ * where there is no eeprom and prevents getting link.
+ */
+ e_dbg("Auto Read Done did not complete\n");
+ }
+ }
+ /* Dummy read to clear the phy wakeup bit after lcd reset */
+ if (hw->mac.type == e1000_pchlan)
+ e1e_rphy(hw, BM_WUC, ®);
+
+ ret_val = e1000e_sw_lcd_config_ich8lan(hw);
+ if (ret_val)
+ goto out;
+
+ if (hw->mac.type == e1000_pchlan) {
+ ret_val = e1000e_oem_bits_config_ich8lan(hw, true);
+ if (ret_val)
+ goto out;
+ }
+ /*
+ * For PCH, this write will make sure that any noise
+ * will be detected as a CRC error and be dropped rather than show up
+ * as a bad packet to the DMA engine.
+ */
+ if (hw->mac.type == e1000_pchlan)
+ ew32(CRC_OFFSET, 0x65656565);
+
+ ew32(IMC, 0xffffffff);
+ icr = er32(ICR);
+
+ kab = er32(KABGTXD);
+ kab |= E1000_KABGTXD_BGSQLBIAS;
+ ew32(KABGTXD, kab);
+
+ if (hw->mac.type == e1000_pchlan)
+ ret_val = e1000e_hv_phy_workarounds_ich8lan(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_init_hw_ich8lan - Initialize the hardware
+ * @hw: pointer to the HW structure
+ *
+ * Prepares the hardware for transmit and receive by doing the following:
+ * - initialize hardware bits
+ * - initialize LED identification
+ * - setup receive address registers
+ * - setup flow control
+ * - setup transmit descriptors
+ * - clear statistics
+ **/
+static s32 e1000e_init_hw_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 ctrl_ext, txdctl, snoop;
+ s32 ret_val;
+ u16 i;
+
+ e1000e_initialize_hw_bits_ich8lan(hw);
+
+ /* Initialize identification LED */
+ ret_val = mac->ops.id_led_init(hw);
+ if (ret_val)
+ /* This is not fatal and we should not stop init due to this */
+ e_dbg("Error initializing identification LED\n");
+
+ /* Setup the receive address. */
+ e1000e_init_rx_addrs(hw, mac->rar_entry_count);
+
+ /* Zero out the Multicast HASH table */
+ e_dbg("Zeroing the MTA\n");
+ for (i = 0; i < mac->mta_reg_count; i++)
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
+
+ /*
+ * The 82578 Rx buffer will stall if wakeup is enabled in host and
+ * the ME. Reading the BM_WUC register will clear the host wakeup bit.
+ * Reset the phy after disabling host wakeup to reset the Rx buffer.
+ */
+ if (hw->phy.type == e1000_phy_82578) {
+ e1e_rphy(hw, BM_WUC, &i);
+ ret_val = e1000e_phy_hw_reset_ich8lan(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Setup link and flow control */
+ ret_val = mac->ops.setup_link(hw);
+
+ /* Set the transmit descriptor write-back policy for both queues */
+ txdctl = er32(TXDCTL(0));
+ txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB;
+ txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) |
+ E1000_TXDCTL_MAX_TX_DESC_PREFETCH;
+ ew32(TXDCTL(0), txdctl);
+ txdctl = er32(TXDCTL(1));
+ txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB;
+ txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) |
+ E1000_TXDCTL_MAX_TX_DESC_PREFETCH;
+ ew32(TXDCTL(1), txdctl);
+
+ /*
+ * ICH8 has opposite polarity of no_snoop bits.
+ * By default, we should use snoop behavior.
+ */
+ if (mac->type == e1000_ich8lan)
+ snoop = PCIE_ICH8_SNOOP_ALL;
+ else
+ snoop = (u32)~(PCIE_NO_SNOOP_ALL);
+ e1000e_set_pcie_no_snoop(hw, snoop);
+
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
+ ew32(CTRL_EXT, ctrl_ext);
+
+ /*
+ * Clear all of the statistics registers (clear on read). It is
+ * important that we do this after we have tried to establish link
+ * because the symbol error count will increment wildly if there
+ * is no link.
+ */
+ e1000e_clear_hw_cntrs_ich8lan(hw);
+
+ return ret_val;
+}
+/**
+ * e1000e_initialize_hw_bits_ich8lan - Initialize required hardware bits
+ * @hw: pointer to the HW structure
+ *
+ * Sets/Clears required hardware bits necessary for correctly setting up the
+ * hardware for transmit and receive.
+ **/
+static void e1000e_initialize_hw_bits_ich8lan(struct e1000_hw *hw)
+{
+ u32 reg;
+
+ /* Extended Device Control */
+ reg = er32(CTRL_EXT);
+ reg |= (1 << 22);
+ /* Enable PHY low-power state when MAC is at D3 w/o WoL */
+ if (hw->mac.type >= e1000_pchlan)
+ reg |= E1000_CTRL_EXT_PHYPDEN;
+ ew32(CTRL_EXT, reg);
+
+ /* Transmit Descriptor Control 0 */
+ reg = er32(TXDCTL(0));
+ reg |= (1 << 22);
+ ew32(TXDCTL(0), reg);
+
+ /* Transmit Descriptor Control 1 */
+ reg = er32(TXDCTL(1));
+ reg |= (1 << 22);
+ ew32(TXDCTL(1), reg);
+
+ /* Transmit Arbitration Control 0 */
+ reg = er32(TARC(0));
+ if (hw->mac.type == e1000_ich8lan)
+ reg |= (1 << 28) | (1 << 29);
+ reg |= (1 << 23) | (1 << 24) | (1 << 26) | (1 << 27);
+ ew32(TARC(0), reg);
+
+ /* Transmit Arbitration Control 1 */
+ reg = er32(TARC(1));
+ if (er32(TCTL) & E1000_TCTL_MULR)
+ reg &= ~(1 << 28);
+ else
+ reg |= (1 << 28);
+ reg |= (1 << 24) | (1 << 26) | (1 << 30);
+ ew32(TARC(1), reg);
+
+ /* Device Status */
+ if (hw->mac.type == e1000_ich8lan) {
+ reg = er32(STATUS);
+ reg &= ~(1 << 31);
+ ew32(STATUS, reg);
+ }
+
+ return;
+}
+
+/**
+ * e1000e_setup_link_ich8lan - Setup flow control and link settings
+ * @hw: pointer to the HW structure
+ *
+ * Determines which flow control settings to use, then configures flow
+ * control. Calls the appropriate media-specific link configuration
+ * function. Assuming the adapter has a valid link partner, a valid link
+ * should be established. Assumes the hardware has previously been reset
+ * and the transmitter and receiver are not enabled.
+ **/
+static s32 e1000e_setup_link_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ if (e1000e_check_reset_block(hw))
+ goto out;
+
+ /*
+ * ICH parts do not have a word in the NVM to determine
+ * the default flow control setting, so we explicitly
+ * set it to full.
+ */
+ if (hw->fc.requested_mode == e1000_fc_default)
+ hw->fc.requested_mode = e1000_fc_full;
+
+ /*
+ * Save off the requested flow control mode for use later. Depending
+ * on the link partner's capabilities, we may or may not use this mode.
+ */
+ hw->fc.current_mode = hw->fc.requested_mode;
+
+ e_dbg("After fix-ups FlowControl is now = %x\n",
+ hw->fc.current_mode);
+
+ /* Continue to configure the copper link. */
+ ret_val = hw->mac.ops.setup_physical_interface(hw);
+ if (ret_val)
+ goto out;
+
+ ew32(FCTTV, hw->fc.pause_time);
+ if ((hw->phy.type == e1000_phy_82578) ||
+ (hw->phy.type == e1000_phy_82577)) {
+ ret_val = e1e_wphy(hw,
+ PHY_REG(BM_PORT_CTRL_PAGE, 27),
+ hw->fc.pause_time);
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_set_fc_watermarks(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_setup_copper_link_ich8lan - Configure MAC/PHY interface
+ * @hw: pointer to the HW structure
+ *
+ * Configures the kumeran interface to the PHY to wait the appropriate time
+ * when polling the PHY, then call the generic setup_copper_link to finish
+ * configuring the copper link.
+ **/
+static s32 e1000e_setup_copper_link_ich8lan(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u16 reg_data;
+
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_SLU;
+ ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ew32(CTRL, ctrl);
+
+ /*
+ * Set the mac to wait the maximum time between each iteration
+ * and increase the max iterations when polling the phy;
+ * this fixes erroneous timeouts at 10Mbps.
+ */
+ ret_val = e1000e_write_kmrn_reg(hw,
+ E1000_KMRNCTRLSTA_TIMEOUTS,
+ 0xFFFF);
+ if (ret_val)
+ goto out;
+ ret_val = e1000e_read_kmrn_reg(hw,
+ E1000_KMRNCTRLSTA_INBAND_PARAM,
+ ®_data);
+ if (ret_val)
+ goto out;
+ reg_data |= 0x3F;
+ ret_val = e1000e_write_kmrn_reg(hw,
+ E1000_KMRNCTRLSTA_INBAND_PARAM,
+ reg_data);
+ if (ret_val)
+ goto out;
+
+ switch (hw->phy.type) {
+ case e1000_phy_igp_3:
+ ret_val = e1000e_copper_link_setup_igp(hw);
+ if (ret_val)
+ goto out;
+ break;
+ case e1000_phy_bm:
+ case e1000_phy_82578:
+ ret_val = e1000e_copper_link_setup_m88(hw);
+ if (ret_val)
+ goto out;
+ break;
+ case e1000_phy_82577:
+ ret_val = e1000e_copper_link_setup_82577(hw);
+ if (ret_val)
+ goto out;
+ break;
+ case e1000_phy_ife:
+ ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL,
+ ®_data);
+ if (ret_val)
+ goto out;
+
+ reg_data &= ~IFE_PMC_AUTO_MDIX;
+
+ switch (hw->phy.mdix) {
+ case 1:
+ reg_data &= ~IFE_PMC_FORCE_MDIX;
+ break;
+ case 2:
+ reg_data |= IFE_PMC_FORCE_MDIX;
+ break;
+ case 0:
+ default:
+ reg_data |= IFE_PMC_AUTO_MDIX;
+ break;
+ }
+ ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL,
+ reg_data);
+ if (ret_val)
+ goto out;
+ break;
+ default:
+ break;
+ }
+ ret_val = e1000e_setup_copper_link(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_get_link_up_info_ich8lan - Get current link speed and duplex
+ * @hw: pointer to the HW structure
+ * @speed: pointer to store current link speed
+ * @duplex: pointer to store the current link duplex
+ *
+ * Calls the generic get_speed_and_duplex to retrieve the current link
+ * information and then calls the Kumeran lock loss workaround for links at
+ * gigabit speeds.
+ **/
+static s32 e1000e_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex)
+{
+ s32 ret_val;
+
+ ret_val = e1000e_get_speed_and_duplex_copper(hw, speed, duplex);
+ if (ret_val)
+ goto out;
+
+ if ((hw->mac.type == e1000_ich8lan) &&
+ (hw->phy.type == e1000_phy_igp_3) &&
+ (*speed == SPEED_1000)) {
+ ret_val = e1000e_kmrn_lock_loss_workaround_ich8lan(hw);
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_kmrn_lock_loss_workaround_ich8lan - Kumeran workaround
+ * @hw: pointer to the HW structure
+ *
+ * Work-around for 82566 Kumeran PCS lock loss:
+ * On link status change (i.e. PCI reset, speed change) and link is up and
+ * speed is gigabit-
+ * 0) if workaround is optionally disabled do nothing
+ * 1) wait 1ms for Kumeran link to come up
+ * 2) check Kumeran Diagnostic register PCS lock loss bit
+ * 3) if not set the link is locked (all is good), otherwise...
+ * 4) reset the PHY
+ * 5) repeat up to 10 times
+ * Note: this is only called for IGP3 copper when speed is 1gb.
+ **/
+static s32 e1000e_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ u32 phy_ctrl;
+ s32 ret_val = E1000_SUCCESS;
+ u16 i, data;
+ bool link;
+
+ if (!(dev_spec->kmrn_lock_loss_workaround_enabled))
+ goto out;
+
+ /*
+ * Make sure link is up before proceeding. If not just return.
+ * Attempting this while link is negotiating fouled up link
+ * stability
+ */
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (!link) {
+ ret_val = E1000_SUCCESS;
+ goto out;
+ }
+
+ for (i = 0; i < 10; i++) {
+ /* read once to clear */
+ ret_val = e1e_rphy(hw, IGP3_KMRN_DIAG, &data);
+ if (ret_val)
+ goto out;
+ /* and again to get new status */
+ ret_val = e1e_rphy(hw, IGP3_KMRN_DIAG, &data);
+ if (ret_val)
+ goto out;
+
+ /* check for PCS lock */
+ if (!(data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS)) {
+ ret_val = E1000_SUCCESS;
+ goto out;
+ }
+
+ /* Issue PHY reset */
+ e1000e_phy_hw_reset(hw);
+ mdelay(5);
+ }
+ /* Disable GigE link negotiation */
+ phy_ctrl = er32(PHY_CTRL);
+ phy_ctrl |= (E1000_PHY_CTRL_GBE_DISABLE |
+ E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
+ ew32(PHY_CTRL, phy_ctrl);
+
+ /*
+ * Call gig speed drop workaround on Gig disable before accessing
+ * any PHY registers
+ */
+ e1000e_gig_downshift_workaround_ich8lan(hw);
+
+ /* unable to acquire PCS lock */
+ ret_val = -E1000_ERR_PHY;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_set_kmrn_lock_loss_workaround_ich8lan - Set Kumeran workaround state
+ * @hw: pointer to the HW structure
+ * @state: boolean value used to set the current Kumeran workaround state
+ *
+ * If ICH8, set the current Kumeran workaround state (enabled - true
+ * /disabled - false).
+ **/
+void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
+ bool state)
+{
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+
+ if (hw->mac.type != e1000_ich8lan) {
+ e_dbg("Workaround applies to ICH8 only.\n");
+ return;
+ }
+
+ dev_spec->kmrn_lock_loss_workaround_enabled = state;
+
+ return;
+}
+
+/**
+ * e1000e_ipg3_phy_powerdown_workaround_ich8lan - Power down workaround on D3
+ * @hw: pointer to the HW structure
+ *
+ * Workaround for 82566 power-down on D3 entry:
+ * 1) disable gigabit link
+ * 2) write VR power-down enable
+ * 3) read it back
+ * Continue if successful, else issue LCD reset and repeat
+ **/
+void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw)
+{
+ u32 reg;
+ u16 data;
+ u8 retry = 0;
+
+ if (hw->phy.type != e1000_phy_igp_3)
+ goto out;
+
+ /* Try the workaround twice (if needed) */
+ do {
+ /* Disable link */
+ reg = er32(PHY_CTRL);
+ reg |= (E1000_PHY_CTRL_GBE_DISABLE |
+ E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
+ ew32(PHY_CTRL, reg);
+
+ /*
+ * Call gig speed drop workaround on Gig disable before
+ * accessing any PHY registers
+ */
+ if (hw->mac.type == e1000_ich8lan)
+ e1000e_gig_downshift_workaround_ich8lan(hw);
+
+ /* Write VR power-down enable */
+ e1e_rphy(hw, IGP3_VR_CTRL, &data);
+ data &= ~IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK;
+ e1e_wphy(hw, IGP3_VR_CTRL,
+ data | IGP3_VR_CTRL_MODE_SHUTDOWN);
+
+ /* Read it back and test */
+ e1e_rphy(hw, IGP3_VR_CTRL, &data);
+ data &= IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK;
+ if ((data == IGP3_VR_CTRL_MODE_SHUTDOWN) || retry)
+ break;
+
+ /* Issue PHY reset and repeat at most one more time */
+ reg = er32(CTRL);
+ ew32(CTRL, reg | E1000_CTRL_PHY_RST);
+ retry++;
+ } while (retry);
+
+out:
+ return;
+}
+
+/**
+ * e1000e_gig_downshift_workaround_ich8lan - WoL from S5 stops working
+ * @hw: pointer to the HW structure
+ *
+ * Steps to take when dropping from 1Gb/s (eg. link cable removal (LSC),
+ * LPLU, Gig disable, MDIC PHY reset):
+ * 1) Set Kumeran Near-end loopback
+ * 2) Clear Kumeran Near-end loopback
+ * Should only be called for ICH8[m] devices with IGP_3 Phy.
+ **/
+void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 reg_data;
+
+ if ((hw->mac.type != e1000_ich8lan) ||
+ (hw->phy.type != e1000_phy_igp_3))
+ goto out;
+
+ ret_val = e1000e_read_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET,
+ ®_data);
+ if (ret_val)
+ goto out;
+ reg_data |= E1000_KMRNCTRLSTA_DIAG_NELPBK;
+ ret_val = e1000e_write_kmrn_reg(hw,
+ E1000_KMRNCTRLSTA_DIAG_OFFSET,
+ reg_data);
+ if (ret_val)
+ goto out;
+ reg_data &= ~E1000_KMRNCTRLSTA_DIAG_NELPBK;
+ ret_val = e1000e_write_kmrn_reg(hw,
+ E1000_KMRNCTRLSTA_DIAG_OFFSET,
+ reg_data);
+out:
+ return;
+}
+
+/**
+ * e1000e_disable_gig_wol_ich8lan - disable gig during WoL
+ * @hw: pointer to the HW structure
+ *
+ * During S0 to Sx transition, it is possible the link remains at gig
+ * instead of negotiating to a lower speed. Before going to Sx, set
+ * 'LPLU Enabled' and 'Gig Disable' to force link speed negotiation
+ * to a lower speed.
+ *
+ * Should only be called for applicable parts.
+ **/
+void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw)
+{
+ u32 phy_ctrl;
+
+ switch (hw->mac.type) {
+ case e1000_ich8lan:
+ case e1000_ich9lan:
+ case e1000_ich10lan:
+ case e1000_pchlan:
+ phy_ctrl = er32(PHY_CTRL);
+ phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU |
+ E1000_PHY_CTRL_GBE_DISABLE;
+ ew32(PHY_CTRL, phy_ctrl);
+
+ if (hw->mac.type == e1000_pchlan)
+ e1000e_phy_hw_reset_ich8lan(hw);
+ default:
+ break;
+ }
+
+ return;
+}
+
+/**
+ * e1000e_cleanup_led_ich8lan - Restore the default LED operation
+ * @hw: pointer to the HW structure
+ *
+ * Return the LED back to the default configuration.
+ **/
+static s32 e1000e_cleanup_led_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ if (hw->phy.type == e1000_phy_ife)
+ ret_val = e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED,
+ 0);
+ else
+ ew32(LEDCTL, hw->mac.ledctl_default);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_led_on_ich8lan - Turn LEDs on
+ * @hw: pointer to the HW structure
+ *
+ * Turn on the LEDs.
+ **/
+static s32 e1000e_led_on_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ if (hw->phy.type == e1000_phy_ife)
+ ret_val = e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED,
+ (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON));
+ else
+ ew32(LEDCTL, hw->mac.ledctl_mode2);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_led_off_ich8lan - Turn LEDs off
+ * @hw: pointer to the HW structure
+ *
+ * Turn off the LEDs.
+ **/
+static s32 e1000e_led_off_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ if (hw->phy.type == e1000_phy_ife)
+ ret_val = e1e_wphy(hw,
+ IFE_PHY_SPECIAL_CONTROL_LED,
+ (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF));
+ else
+ ew32(LEDCTL, hw->mac.ledctl_mode1);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_setup_led_pchlan - Configures SW controllable LED
+ * @hw: pointer to the HW structure
+ *
+ * This prepares the SW controllable LED for use.
+ **/
+static s32 e1000e_setup_led_pchlan(struct e1000_hw *hw)
+{
+ return e1e_wphy(hw, HV_LED_CONFIG,
+ (u16)hw->mac.ledctl_mode1);
+}
+
+/**
+ * e1000e_cleanup_led_pchlan - Restore the default LED operation
+ * @hw: pointer to the HW structure
+ *
+ * Return the LED back to the default configuration.
+ **/
+static s32 e1000e_cleanup_led_pchlan(struct e1000_hw *hw)
+{
+ return e1e_wphy(hw, HV_LED_CONFIG,
+ (u16)hw->mac.ledctl_default);
+}
+
+/**
+ * e1000e_led_on_pchlan - Turn LEDs on
+ * @hw: pointer to the HW structure
+ *
+ * Turn on the LEDs.
+ **/
+static s32 e1000e_led_on_pchlan(struct e1000_hw *hw)
+{
+ u16 data = (u16)hw->mac.ledctl_mode2;
+ u32 i, led;
+
+ /*
+ * If no link, then turn LED on by setting the invert bit
+ * for each LED that's mode is "link_up" in ledctl_mode2.
+ */
+ if (!(er32(STATUS) & E1000_STATUS_LU)) {
+ for (i = 0; i < 3; i++) {
+ led = (data >> (i * 5)) & E1000_PHY_LED0_MASK;
+ if ((led & E1000_PHY_LED0_MODE_MASK) !=
+ E1000_LEDCTL_MODE_LINK_UP)
+ continue;
+ if (led & E1000_PHY_LED0_IVRT)
+ data &= ~(E1000_PHY_LED0_IVRT << (i * 5));
+ else
+ data |= (E1000_PHY_LED0_IVRT << (i * 5));
+ }
+ }
+
+ return e1e_wphy(hw, HV_LED_CONFIG, data);
+}
+
+/**
+ * e1000e_led_off_pchlan - Turn LEDs off
+ * @hw: pointer to the HW structure
+ *
+ * Turn off the LEDs.
+ **/
+static s32 e1000e_led_off_pchlan(struct e1000_hw *hw)
+{
+ u16 data = (u16)hw->mac.ledctl_mode1;
+ u32 i, led;
+
+ /*
+ * If no link, then turn LED off by clearing the invert bit
+ * for each LED that's mode is "link_up" in ledctl_mode1.
+ */
+ if (!(er32(STATUS) & E1000_STATUS_LU)) {
+ for (i = 0; i < 3; i++) {
+ led = (data >> (i * 5)) & E1000_PHY_LED0_MASK;
+ if ((led & E1000_PHY_LED0_MODE_MASK) !=
+ E1000_LEDCTL_MODE_LINK_UP)
+ continue;
+ if (led & E1000_PHY_LED0_IVRT)
+ data &= ~(E1000_PHY_LED0_IVRT << (i * 5));
+ else
+ data |= (E1000_PHY_LED0_IVRT << (i * 5));
+ }
+ }
+
+ return e1e_wphy(hw, HV_LED_CONFIG, data);
+}
+
+/**
+ * e1000e_get_cfg_done_ich8lan - Read config done bit
+ * @hw: pointer to the HW structure
+ *
+ * Read the management control register for the config done bit for
+ * completion status. NOTE: silicon which is EEPROM-less will fail trying
+ * to read the config done bit, so an error is *ONLY* logged and returns
+ * E1000_SUCCESS. If we were to return with error, EEPROM-less silicon
+ * would not be able to be reset or change link.
+ **/
+static s32 e1000e_get_cfg_done_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u32 bank = 0;
+
+ if (hw->mac.type >= e1000_pchlan) {
+ u32 status = er32(STATUS);
+
+ if (status & E1000_STATUS_PHYRA) {
+ ew32(STATUS, status &
+ ~E1000_STATUS_PHYRA);
+ } else
+ e_dbg("PHY Reset Asserted not set - needs delay\n");
+ }
+
+ e1000e_get_cfg_done(hw);
+
+ /* If EEPROM is not marked present, init the IGP 3 PHY manually */
+ if ((hw->mac.type != e1000_ich10lan) &&
+ (hw->mac.type != e1000_pchlan)) {
+ if (((er32(EECD) & E1000_EECD_PRES) == 0) &&
+ (hw->phy.type == e1000_phy_igp_3)) {
+ e1000e_phy_init_script_igp3(hw);
+ }
+ } else {
+ if (e1000e_valid_nvm_bank_detect_ich8lan(hw, &bank)) {
+ /* Maybe we should do a basic PHY config */
+ e_dbg("EEPROM not present\n");
+ ret_val = -E1000_ERR_CONFIG;
+ }
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_power_down_phy_copper_ich8lan - Remove link during PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, remove the link.
+ **/
+static void e1000e_power_down_phy_copper_ich8lan(struct e1000_hw *hw)
+{
+ /* If the management interface is not enabled, then power down */
+ if (!(hw->mac.ops.check_mng_mode(hw) ||
+ e1000e_check_reset_block(hw)))
+ e1000e_power_down_phy_copper(hw);
+
+ return;
+}
+
+/**
+ * e1000e_clear_hw_cntrs_ich8lan - Clear statistical counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears hardware counters specific to the silicon family and calls
+ * clear_hw_cntrs_generic to clear all general purpose counters.
+ **/
+static void e1000e_clear_hw_cntrs_ich8lan(struct e1000_hw *hw __unused)
+{
+#if 0
+ u16 phy_data;
+
+ e1000e_clear_hw_cntrs_base(hw);
+
+ er32(ALGNERRC);
+ er32(RXERRC);
+ er32(TNCRS);
+ er32(CEXTERR);
+ er32(TSCTC);
+ er32(TSCTFC);
+
+ er32(MGTPRC);
+ er32(MGTPDC);
+ er32(MGTPTC);
+
+ er32(IAC);
+ er32(ICRXOC);
+
+ /* Clear PHY statistics registers */
+ if ((hw->phy.type == e1000_phy_82578) ||
+ (hw->phy.type == e1000_phy_82577)) {
+ e1e_rphy(hw, HV_SCC_UPPER, &phy_data);
+ e1e_rphy(hw, HV_SCC_LOWER, &phy_data);
+ e1e_rphy(hw, HV_ECOL_UPPER, &phy_data);
+ e1e_rphy(hw, HV_ECOL_LOWER, &phy_data);
+ e1e_rphy(hw, HV_MCC_UPPER, &phy_data);
+ e1e_rphy(hw, HV_MCC_LOWER, &phy_data);
+ e1e_rphy(hw, HV_LATECOL_UPPER, &phy_data);
+ e1e_rphy(hw, HV_LATECOL_LOWER, &phy_data);
+ e1e_rphy(hw, HV_COLC_UPPER, &phy_data);
+ e1e_rphy(hw, HV_COLC_LOWER, &phy_data);
+ e1e_rphy(hw, HV_DC_UPPER, &phy_data);
+ e1e_rphy(hw, HV_DC_LOWER, &phy_data);
+ e1e_rphy(hw, HV_TNCRS_UPPER, &phy_data);
+ e1e_rphy(hw, HV_TNCRS_LOWER, &phy_data);
+ }
+#endif
+}
+
+static struct pci_device_id e1000e_ich8lan_nics[] = {
+ PCI_ROM(0x8086, 0x104C, "E1000_DEV_ID_ICH8_IFE", "E1000_DEV_ID_ICH8_IFE", board_ich8lan),
+ PCI_ROM(0x8086, 0x10C5, "E1000_DEV_ID_ICH8_IFE_G", "E1000_DEV_ID_ICH8_IFE_G", board_ich8lan),
+ PCI_ROM(0x8086, 0x10C4, "E1000_DEV_ID_ICH8_IFE_GT", "E1000_DEV_ID_ICH8_IFE_GT", board_ich8lan),
+ PCI_ROM(0x8086, 0x104A, "E1000_DEV_ID_ICH8_IGP_AMT", "E1000_DEV_ID_ICH8_IGP_AMT", board_ich8lan),
+ PCI_ROM(0x8086, 0x104B, "E1000_DEV_ID_ICH8_IGP_C", "E1000_DEV_ID_ICH8_IGP_C", board_ich8lan),
+ PCI_ROM(0x8086, 0x104D, "E1000_DEV_ID_ICH8_IGP_M", "E1000_DEV_ID_ICH8_IGP_M", board_ich8lan),
+ PCI_ROM(0x8086, 0x1049, "E1000_DEV_ID_ICH8_IGP_M_AMT", "E1000_DEV_ID_ICH8_IGP_M_AMT", board_ich8lan),
+ PCI_ROM(0x8086, 0x1501, "E1000_DEV_ID_ICH8_82567V_3", "E1000_DEV_ID_ICH8_82567V_3", board_ich8lan),
+ PCI_ROM(0x8086, 0x10C0, "E1000_DEV_ID_ICH9_IFE", "E1000_DEV_ID_ICH9_IFE", board_ich9lan),
+ PCI_ROM(0x8086, 0x10C2, "E1000_DEV_ID_ICH9_IFE_G", "E1000_DEV_ID_ICH9_IFE_G", board_ich9lan),
+ PCI_ROM(0x8086, 0x10C3, "E1000_DEV_ID_ICH9_IFE_GT", "E1000_DEV_ID_ICH9_IFE_GT", board_ich9lan),
+ PCI_ROM(0x8086, 0x10BD, "E1000_DEV_ID_ICH9_IGP_AMT", "E1000_DEV_ID_ICH9_IGP_AMT", board_ich9lan),
+ PCI_ROM(0x8086, 0x294C, "E1000_DEV_ID_ICH9_IGP_C", "E1000_DEV_ID_ICH9_IGP_C", board_ich9lan),
+ PCI_ROM(0x8086, 0x10E5, "E1000_DEV_ID_ICH9_BM", "E1000_DEV_ID_ICH9_BM", board_ich9lan),
+ PCI_ROM(0x8086, 0x10BF, "E1000_DEV_ID_ICH9_IGP_M", "E1000_DEV_ID_ICH9_IGP_M", board_ich9lan),
+ PCI_ROM(0x8086, 0x10F5, "E1000_DEV_ID_ICH9_IGP_M_AMT", "E1000_DEV_ID_ICH9_IGP_M_AMT", board_ich9lan),
+ PCI_ROM(0x8086, 0x10CB, "E1000_DEV_ID_ICH9_IGP_M_V", "E1000_DEV_ID_ICH9_IGP_M_V", board_ich9lan),
+ PCI_ROM(0x8086, 0x10CC, "E1000_DEV_ID_ICH10_R_BM_LM", "E1000_DEV_ID_ICH10_R_BM_LM", board_ich9lan),
+ PCI_ROM(0x8086, 0x10CD, "E1000_DEV_ID_ICH10_R_BM_LF", "E1000_DEV_ID_ICH10_R_BM_LF", board_ich9lan),
+ PCI_ROM(0x8086, 0x10CE, "E1000_DEV_ID_ICH10_R_BM_V", "E1000_DEV_ID_ICH10_R_BM_V", board_ich9lan),
+ PCI_ROM(0x8086, 0x10DE, "E1000_DEV_ID_ICH10_D_BM_LM", "E1000_DEV_ID_ICH10_D_BM_LM", board_ich10lan),
+ PCI_ROM(0x8086, 0x10DF, "E1000_DEV_ID_ICH10_D_BM_LF", "E1000_DEV_ID_ICH10_D_BM_LF", board_ich10lan),
+ PCI_ROM(0x8086, 0x10EA, "E1000_DEV_ID_PCH_M_HV_LM", "E1000_DEV_ID_PCH_M_HV_LM", board_pchlan),
+ PCI_ROM(0x8086, 0x10EB, "E1000_DEV_ID_PCH_M_HV_LC", "E1000_DEV_ID_PCH_M_HV_LC", board_pchlan),
+ PCI_ROM(0x8086, 0x10EF, "E1000_DEV_ID_PCH_D_HV_DM", "E1000_DEV_ID_PCH_D_HV_DM", board_pchlan),
+ PCI_ROM(0x8086, 0x10F0, "E1000_DEV_ID_PCH_D_HV_DC", "E1000_DEV_ID_PCH_D_HV_DC", board_pchlan),
+};
+
+struct pci_driver e1000e_ich8lan_driver __pci_driver = {
+ .ids = e1000e_ich8lan_nics,
+ .id_count = (sizeof (e1000e_ich8lan_nics) / sizeof (e1000e_ich8lan_nics[0])),
+ .probe = e1000e_probe,
+ .remove = e1000e_remove,
+};
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#ifndef _E1000E_ICH8LAN_H_
+#define _E1000E_ICH8LAN_H_
+
+#define ICH_FLASH_GFPREG 0x0000
+#define ICH_FLASH_HSFSTS 0x0004
+#define ICH_FLASH_HSFCTL 0x0006
+#define ICH_FLASH_FADDR 0x0008
+#define ICH_FLASH_FDATA0 0x0010
+
+/* Requires up to 10 seconds when MNG might be accessing part. */
+#define ICH_FLASH_READ_COMMAND_TIMEOUT 10000000
+#define ICH_FLASH_WRITE_COMMAND_TIMEOUT 10000000
+#define ICH_FLASH_ERASE_COMMAND_TIMEOUT 10000000
+#define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
+#define ICH_FLASH_CYCLE_REPEAT_COUNT 10
+
+#define ICH_CYCLE_READ 0
+#define ICH_CYCLE_WRITE 2
+#define ICH_CYCLE_ERASE 3
+
+#define FLASH_GFPREG_BASE_MASK 0x1FFF
+#define FLASH_SECTOR_ADDR_SHIFT 12
+
+#define ICH_FLASH_SEG_SIZE_256 256
+#define ICH_FLASH_SEG_SIZE_4K 4096
+#define ICH_FLASH_SEG_SIZE_8K 8192
+#define ICH_FLASH_SEG_SIZE_64K 65536
+#define ICH_FLASH_SECTOR_SIZE 4096
+
+#define ICH_FLASH_REG_MAPSIZE 0x00A0
+
+#define E1000_ICH_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI Reset */
+#define E1000_ICH_FWSM_DISSW 0x10000000 /* FW Disables SW Writes */
+/* FW established a valid mode */
+#define E1000_ICH_FWSM_FW_VALID 0x00008000
+
+#define E1000_ICH_MNG_IAMT_MODE 0x2
+
+#define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \
+ (ID_LED_OFF1_OFF2 << 8) | \
+ (ID_LED_OFF1_ON2 << 4) | \
+ (ID_LED_DEF1_DEF2))
+
+#define E1000_ICH_NVM_SIG_WORD 0x13
+#define E1000_ICH_NVM_SIG_MASK 0xC000
+#define E1000_ICH_NVM_VALID_SIG_MASK 0xC0
+#define E1000_ICH_NVM_SIG_VALUE 0x80
+
+#define E1000_ICH8_LAN_INIT_TIMEOUT 1500
+
+#define E1000_FEXTNVM_SW_CONFIG 1
+#define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* Bit redefined for ICH8M */
+
+#define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL
+
+#define E1000_ICH_RAR_ENTRIES 7
+
+#define PHY_PAGE_SHIFT 5
+#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
+ ((reg) & MAX_PHY_REG_ADDRESS))
+#define IGP3_KMRN_DIAG PHY_REG(770, 19) /* KMRN Diagnostic */
+#define IGP3_VR_CTRL PHY_REG(776, 18) /* Voltage Regulator Control */
+#define IGP3_CAPABILITY PHY_REG(776, 19) /* Capability */
+#define IGP3_PM_CTRL PHY_REG(769, 20) /* Power Management Control */
+
+#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002
+#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300
+#define IGP3_VR_CTRL_MODE_SHUTDOWN 0x0200
+#define IGP3_PM_CTRL_FORCE_PWR_DOWN 0x0020
+
+/* PHY Wakeup Registers and defines */
+#define BM_RCTL PHY_REG(BM_WUC_PAGE, 0)
+#define BM_WUC PHY_REG(BM_WUC_PAGE, 1)
+#define BM_WUFC PHY_REG(BM_WUC_PAGE, 2)
+#define BM_WUS PHY_REG(BM_WUC_PAGE, 3)
+#define BM_RAR_L(_i) (BM_PHY_REG(BM_WUC_PAGE, 16 + ((_i) << 2)))
+#define BM_RAR_M(_i) (BM_PHY_REG(BM_WUC_PAGE, 17 + ((_i) << 2)))
+#define BM_RAR_H(_i) (BM_PHY_REG(BM_WUC_PAGE, 18 + ((_i) << 2)))
+#define BM_RAR_CTRL(_i) (BM_PHY_REG(BM_WUC_PAGE, 19 + ((_i) << 2)))
+#define BM_MTA(_i) (BM_PHY_REG(BM_WUC_PAGE, 128 + ((_i) << 1)))
+
+#define BM_RCTL_UPE 0x0001 /* Unicast Promiscuous Mode */
+#define BM_RCTL_MPE 0x0002 /* Multicast Promiscuous Mode */
+#define BM_RCTL_MO_SHIFT 3 /* Multicast Offset Shift */
+#define BM_RCTL_MO_MASK (3 << 3) /* Multicast Offset Mask */
+#define BM_RCTL_BAM 0x0020 /* Broadcast Accept Mode */
+#define BM_RCTL_PMCF 0x0040 /* Pass MAC Control Frames */
+#define BM_RCTL_RFCE 0x0080 /* Rx Flow Control Enable */
+
+#define HV_LED_CONFIG PHY_REG(768, 30) /* LED Configuration */
+#define HV_MUX_DATA_CTRL PHY_REG(776, 16)
+#define HV_MUX_DATA_CTRL_GEN_TO_MAC 0x0400
+#define HV_MUX_DATA_CTRL_FORCE_SPEED 0x0004
+#define HV_SCC_UPPER PHY_REG(778, 16) /* Single Collision Count */
+#define HV_SCC_LOWER PHY_REG(778, 17)
+#define HV_ECOL_UPPER PHY_REG(778, 18) /* Excessive Collision Count */
+#define HV_ECOL_LOWER PHY_REG(778, 19)
+#define HV_MCC_UPPER PHY_REG(778, 20) /* Multiple Collision Count */
+#define HV_MCC_LOWER PHY_REG(778, 21)
+#define HV_LATECOL_UPPER PHY_REG(778, 23) /* Late Collision Count */
+#define HV_LATECOL_LOWER PHY_REG(778, 24)
+#define HV_COLC_UPPER PHY_REG(778, 25) /* Collision Count */
+#define HV_COLC_LOWER PHY_REG(778, 26)
+#define HV_DC_UPPER PHY_REG(778, 27) /* Defer Count */
+#define HV_DC_LOWER PHY_REG(778, 28)
+#define HV_TNCRS_UPPER PHY_REG(778, 29) /* Transmit with no CRS */
+#define HV_TNCRS_LOWER PHY_REG(778, 30)
+
+#define E1000_FCRTV_PCH 0x05F40 /* PCH Flow Control Refresh Timer Value */
+
+#define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */
+#define E1000_NVM_K1_ENABLE 0x1 /* NVM Enable K1 bit */
+
+/* SMBus Address Phy Register */
+#define HV_SMB_ADDR PHY_REG(768, 26)
+#define HV_SMB_ADDR_PEC_EN 0x0200
+#define HV_SMB_ADDR_VALID 0x0080
+
+/* Strapping Option Register - RO */
+#define E1000_STRAP 0x0000C
+#define E1000_STRAP_SMBUS_ADDRESS_MASK 0x00FE0000
+#define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17
+
+/* OEM Bits Phy Register */
+#define HV_OEM_BITS PHY_REG(768, 25)
+#define HV_OEM_BITS_LPLU 0x0004 /* Low Power Link Up */
+#define HV_OEM_BITS_GBE_DIS 0x0040 /* Gigabit Disable */
+#define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */
+
+#define LCD_CFG_PHY_ADDR_BIT 0x0020 /* Phy address bit from LCD Config word */
+
+#define SW_FLAG_TIMEOUT 1000 /* SW Semaphore flag timeout in milliseconds */
+
+/*
+ * Additional interrupts need to be handled for ICH family:
+ * DSW = The FW changed the status of the DISSW bit in FWSM
+ * PHYINT = The LAN connected device generates an interrupt
+ * EPRST = Manageability reset event
+ */
+#define IMS_ICH_ENABLE_MASK (\
+ E1000_IMS_DSW | \
+ E1000_IMS_PHYINT | \
+ E1000_IMS_EPRST)
+
+/* Additional interrupt register bit definitions */
+#define E1000_ICR_LSECPNC 0x00004000 /* PN threshold - client */
+#define E1000_IMS_LSECPNC E1000_ICR_LSECPNC /* PN threshold - client */
+#define E1000_ICS_LSECPNC E1000_ICR_LSECPNC /* PN threshold - client */
+
+/* Security Processing bit Indication */
+#define E1000_RXDEXT_LINKSEC_STATUS_LSECH 0x01000000
+#define E1000_RXDEXT_LINKSEC_ERROR_BIT_MASK 0x60000000
+#define E1000_RXDEXT_LINKSEC_ERROR_NO_SA_MATCH 0x20000000
+#define E1000_RXDEXT_LINKSEC_ERROR_REPLAY_ERROR 0x40000000
+#define E1000_RXDEXT_LINKSEC_ERROR_BAD_SIG 0x60000000
+
+
+void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
+ bool state);
+void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
+void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw);
+void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw);
+s32 e1000e_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
+s32 e1000e_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_config);
+
+#endif
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#include "e1000e.h"
+
+static u32 e1000e_hash_mc_addr_generic(struct e1000_hw *hw, u8 *mc_addr);
+static s32 e1000e_set_default_fc_generic(struct e1000_hw *hw);
+static s32 e1000e_commit_fc_settings_generic(struct e1000_hw *hw);
+static s32 e1000e_poll_fiber_serdes_link_generic(struct e1000_hw *hw);
+static s32 e1000e_validate_mdi_setting_generic(struct e1000_hw *hw);
+static void e1000e_set_lan_id_multi_port_pcie(struct e1000_hw *hw);
+
+/**
+ * e1000e_init_mac_ops_generic - Initialize MAC function pointers
+ * @hw: pointer to the HW structure
+ *
+ * Setups up the function pointers to no-op functions
+ **/
+void e1000e_init_mac_ops_generic(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ /* General Setup */
+ mac->ops.set_lan_id = e1000e_set_lan_id_multi_port_pcie;
+ mac->ops.read_mac_addr = e1000e_read_mac_addr_generic;
+ mac->ops.config_collision_dist = e1000e_config_collision_dist;
+ /* LINK */
+ mac->ops.wait_autoneg = e1000e_wait_autoneg;
+ /* Management */
+#if 0
+ mac->ops.mng_host_if_write = e1000e_mng_host_if_write_generic;
+ mac->ops.mng_write_cmd_header = e1000e_mng_write_cmd_header_generic;
+ mac->ops.mng_enable_host_if = e1000e_mng_enable_host_if_generic;
+#endif
+ /* VLAN, MC, etc. */
+ mac->ops.rar_set = e1000e_rar_set;
+ mac->ops.validate_mdi_setting = e1000e_validate_mdi_setting_generic;
+}
+
+/**
+ * e1000e_get_bus_info_pcie - Get PCIe bus information
+ * @hw: pointer to the HW structure
+ *
+ * Determines and stores the system bus information for a particular
+ * network interface. The following bus information is determined and stored:
+ * bus speed, bus width, type (PCIe), and PCIe function.
+ **/
+s32 e1000e_get_bus_info_pcie(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ struct e1000_bus_info *bus = &hw->bus;
+
+ s32 ret_val;
+ u16 pcie_link_status;
+
+ bus->type = e1000_bus_type_pci_express;
+ bus->speed = e1000_bus_speed_2500;
+
+ ret_val = e1000e_read_pcie_cap_reg(hw,
+ PCIE_LINK_STATUS,
+ &pcie_link_status);
+ if (ret_val)
+ bus->width = e1000_bus_width_unknown;
+ else
+ bus->width = (enum e1000_bus_width)((pcie_link_status &
+ PCIE_LINK_WIDTH_MASK) >>
+ PCIE_LINK_WIDTH_SHIFT);
+
+ mac->ops.set_lan_id(hw);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_set_lan_id_multi_port_pcie - Set LAN id for PCIe multiple port devices
+ *
+ * @hw: pointer to the HW structure
+ *
+ * Determines the LAN function id by reading memory-mapped registers
+ * and swaps the port value if requested.
+ **/
+static void e1000e_set_lan_id_multi_port_pcie(struct e1000_hw *hw)
+{
+ struct e1000_bus_info *bus = &hw->bus;
+ u32 reg;
+
+ /*
+ * The status register reports the correct function number
+ * for the device regardless of function swap state.
+ */
+ reg = er32(STATUS);
+ bus->func = (reg & E1000_STATUS_FUNC_MASK) >> E1000_STATUS_FUNC_SHIFT;
+}
+
+/**
+ * e1000e_set_lan_id_single_port - Set LAN id for a single port device
+ * @hw: pointer to the HW structure
+ *
+ * Sets the LAN function id to zero for a single port device.
+ **/
+void e1000e_set_lan_id_single_port(struct e1000_hw *hw)
+{
+ struct e1000_bus_info *bus = &hw->bus;
+
+ bus->func = 0;
+}
+
+/**
+ * e1000e_clear_vfta_generic - Clear VLAN filter table
+ * @hw: pointer to the HW structure
+ *
+ * Clears the register array which contains the VLAN filter table by
+ * setting all the values to 0.
+ **/
+void e1000e_clear_vfta_generic(struct e1000_hw *hw)
+{
+ u32 offset;
+
+ for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
+ E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, 0);
+ e1e_flush();
+ }
+}
+
+/**
+ * e1000e_write_vfta_generic - Write value to VLAN filter table
+ * @hw: pointer to the HW structure
+ * @offset: register offset in VLAN filter table
+ * @value: register value written to VLAN filter table
+ *
+ * Writes value at the given offset in the register array which stores
+ * the VLAN filter table.
+ **/
+void e1000e_write_vfta_generic(struct e1000_hw *hw, u32 offset, u32 value)
+{
+ E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, value);
+ e1e_flush();
+}
+
+/**
+ * e1000e_init_rx_addrs - Initialize receive address's
+ * @hw: pointer to the HW structure
+ * @rar_count: receive address registers
+ *
+ * Setups the receive address registers by setting the base receive address
+ * register to the devices MAC address and clearing all the other receive
+ * address registers to 0.
+ **/
+void e1000e_init_rx_addrs(struct e1000_hw *hw, u16 rar_count)
+{
+ u32 i;
+ u8 mac_addr[ETH_ADDR_LEN] = {0};
+
+ /* Setup the receive address */
+ e_dbg("Programming MAC Address into RAR[0]\n");
+
+ hw->mac.ops.rar_set(hw, hw->mac.addr, 0);
+
+ /* Zero out the other (rar_entry_count - 1) receive addresses */
+ e_dbg("Clearing RAR[1-%u]\n", rar_count-1);
+ for (i = 1; i < rar_count; i++)
+ hw->mac.ops.rar_set(hw, mac_addr, i);
+}
+
+/**
+ * e1000e_check_alt_mac_addr_generic - Check for alternate MAC addr
+ * @hw: pointer to the HW structure
+ *
+ * Checks the nvm for an alternate MAC address. An alternate MAC address
+ * can be setup by pre-boot software and must be treated like a permanent
+ * address and must override the actual permanent MAC address. If an
+ * alternate MAC address is found it is programmed into RAR0, replacing
+ * the permanent address that was installed into RAR0 by the Si on reset.
+ * This function will return SUCCESS unless it encounters an error while
+ * reading the EEPROM.
+ **/
+s32 e1000e_check_alt_mac_addr_generic(struct e1000_hw *hw)
+{
+ u32 i;
+ s32 ret_val = E1000_SUCCESS;
+ u16 offset, nvm_alt_mac_addr_offset, nvm_data;
+ u8 alt_mac_addr[ETH_ADDR_LEN];
+
+ ret_val = e1000e_read_nvm(hw, NVM_ALT_MAC_ADDR_PTR, 1,
+ &nvm_alt_mac_addr_offset);
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ goto out;
+ }
+
+ if (nvm_alt_mac_addr_offset == 0xFFFF) {
+ /* There is no Alternate MAC Address */
+ goto out;
+ }
+
+ if (hw->bus.func == E1000_FUNC_1)
+ nvm_alt_mac_addr_offset += E1000_ALT_MAC_ADDRESS_OFFSET_LAN1;
+ for (i = 0; i < ETH_ADDR_LEN; i += 2) {
+ offset = nvm_alt_mac_addr_offset + (i >> 1);
+ ret_val = e1000e_read_nvm(hw, offset, 1, &nvm_data);
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ goto out;
+ }
+
+ alt_mac_addr[i] = (u8)(nvm_data & 0xFF);
+ alt_mac_addr[i + 1] = (u8)(nvm_data >> 8);
+ }
+
+ /* if multicast bit is set, the alternate address will not be used */
+ if (alt_mac_addr[0] & 0x01) {
+ e_dbg("Ignoring Alternate Mac Address with MC bit set\n");
+ goto out;
+ }
+
+ /*
+ * We have a valid alternate MAC address, and we want to treat it the
+ * same as the normal permanent MAC address stored by the HW into the
+ * RAR. Do this by mapping this address into RAR0.
+ */
+ hw->mac.ops.rar_set(hw, alt_mac_addr, 0);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_rar_set - Set receive address register
+ * @hw: pointer to the HW structure
+ * @addr: pointer to the receive address
+ * @index: receive address array register
+ *
+ * Sets the receive address array register at index to the address passed
+ * in by addr.
+ **/
+void e1000e_rar_set(struct e1000_hw *hw, u8 *addr, u32 index)
+{
+ u32 rar_low, rar_high;
+
+ /*
+ * HW expects these in little endian so we reverse the byte order
+ * from network order (big endian) to little endian
+ */
+ rar_low = ((u32) addr[0] |
+ ((u32) addr[1] << 8) |
+ ((u32) addr[2] << 16) | ((u32) addr[3] << 24));
+
+ rar_high = ((u32) addr[4] | ((u32) addr[5] << 8));
+
+ /* If MAC address zero, no need to set the AV bit */
+ if (rar_low || rar_high)
+ rar_high |= E1000_RAH_AV;
+
+ /*
+ * Some bridges will combine consecutive 32-bit writes into
+ * a single burst write, which will malfunction on some parts.
+ * The flushes avoid this.
+ */
+ ew32(RAL(index), rar_low);
+ e1e_flush();
+ ew32(RAH(index), rar_high);
+ e1e_flush();
+}
+
+/**
+ * e1000e_mta_set_generic - Set multicast filter table address
+ * @hw: pointer to the HW structure
+ * @hash_value: determines the MTA register and bit to set
+ *
+ * The multicast table address is a register array of 32-bit registers.
+ * The hash_value is used to determine what register the bit is in, the
+ * current value is read, the new bit is OR'd in and the new value is
+ * written back into the register.
+ **/
+void e1000e_mta_set_generic(struct e1000_hw *hw, u32 hash_value)
+{
+ u32 hash_bit, hash_reg, mta;
+
+ /*
+ * The MTA is a register array of 32-bit registers. It is
+ * treated like an array of (32*mta_reg_count) bits. We want to
+ * set bit BitArray[hash_value]. So we figure out what register
+ * the bit is in, read it, OR in the new bit, then write
+ * back the new value. The (hw->mac.mta_reg_count - 1) serves as a
+ * mask to bits 31:5 of the hash value which gives us the
+ * register we're modifying. The hash bit within that register
+ * is determined by the lower 5 bits of the hash value.
+ */
+ hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1);
+ hash_bit = hash_value & 0x1F;
+
+ mta = E1000_READ_REG_ARRAY(hw, E1000_MTA, hash_reg);
+
+ mta |= (1 << hash_bit);
+
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, hash_reg, mta);
+ e1e_flush();
+}
+
+/**
+ * e1000e_update_mc_addr_list_generic - Update Multicast addresses
+ * @hw: pointer to the HW structure
+ * @mc_addr_list: array of multicast addresses to program
+ * @mc_addr_count: number of multicast addresses to program
+ *
+ * Updates entire Multicast Table Array.
+ * The caller must have a packed mc_addr_list of multicast addresses.
+ **/
+void e1000e_update_mc_addr_list_generic(struct e1000_hw *hw,
+ u8 *mc_addr_list, u32 mc_addr_count)
+{
+ u32 hash_value, hash_bit, hash_reg;
+ int i;
+
+ /* clear mta_shadow */
+ memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow));
+
+ /* update mta_shadow from mc_addr_list */
+ for (i = 0; (u32) i < mc_addr_count; i++) {
+ hash_value = e1000e_hash_mc_addr_generic(hw, mc_addr_list);
+
+ hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1);
+ hash_bit = hash_value & 0x1F;
+
+ hw->mac.mta_shadow[hash_reg] |= (1 << hash_bit);
+ mc_addr_list += (ETH_ADDR_LEN);
+ }
+
+ /* replace the entire MTA table */
+ for (i = hw->mac.mta_reg_count - 1; i >= 0; i--)
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, hw->mac.mta_shadow[i]);
+ e1e_flush();
+}
+
+/**
+ * e1000e_hash_mc_addr_generic - Generate a multicast hash value
+ * @hw: pointer to the HW structure
+ * @mc_addr: pointer to a multicast address
+ *
+ * Generates a multicast address hash value which is used to determine
+ * the multicast filter table array address and new table value. See
+ * e1000e_mta_set_generic()
+ **/
+static u32 e1000e_hash_mc_addr_generic(struct e1000_hw *hw, u8 *mc_addr)
+{
+ u32 hash_value, hash_mask;
+ u8 bit_shift = 0;
+
+ /* Register count multiplied by bits per register */
+ hash_mask = (hw->mac.mta_reg_count * 32) - 1;
+
+ /*
+ * For a mc_filter_type of 0, bit_shift is the number of left-shifts
+ * where 0xFF would still fall within the hash mask.
+ */
+ while (hash_mask >> bit_shift != 0xFF)
+ bit_shift++;
+
+ /*
+ * The portion of the address that is used for the hash table
+ * is determined by the mc_filter_type setting.
+ * The algorithm is such that there is a total of 8 bits of shifting.
+ * The bit_shift for a mc_filter_type of 0 represents the number of
+ * left-shifts where the MSB of mc_addr[5] would still fall within
+ * the hash_mask. Case 0 does this exactly. Since there are a total
+ * of 8 bits of shifting, then mc_addr[4] will shift right the
+ * remaining number of bits. Thus 8 - bit_shift. The rest of the
+ * cases are a variation of this algorithm...essentially raising the
+ * number of bits to shift mc_addr[5] left, while still keeping the
+ * 8-bit shifting total.
+ *
+ * For example, given the following Destination MAC Address and an
+ * mta register count of 128 (thus a 4096-bit vector and 0xFFF mask),
+ * we can see that the bit_shift for case 0 is 4. These are the hash
+ * values resulting from each mc_filter_type...
+ * [0] [1] [2] [3] [4] [5]
+ * 01 AA 00 12 34 56
+ * LSB MSB
+ *
+ * case 0: hash_value = ((0x34 >> 4) | (0x56 << 4)) & 0xFFF = 0x563
+ * case 1: hash_value = ((0x34 >> 3) | (0x56 << 5)) & 0xFFF = 0xAC6
+ * case 2: hash_value = ((0x34 >> 2) | (0x56 << 6)) & 0xFFF = 0x163
+ * case 3: hash_value = ((0x34 >> 0) | (0x56 << 8)) & 0xFFF = 0x634
+ */
+ switch (hw->mac.mc_filter_type) {
+ default:
+ case 0:
+ break;
+ case 1:
+ bit_shift += 1;
+ break;
+ case 2:
+ bit_shift += 2;
+ break;
+ case 3:
+ bit_shift += 4;
+ break;
+ }
+
+ hash_value = hash_mask & (((mc_addr[4] >> (8 - bit_shift)) |
+ (((u16) mc_addr[5]) << bit_shift)));
+
+ return hash_value;
+}
+
+/**
+ * e1000e_clear_hw_cntrs_base - Clear base hardware counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears the base hardware counters by reading the counter registers.
+ **/
+void e1000e_clear_hw_cntrs_base(struct e1000_hw *hw __unused)
+{
+#if 0
+ er32(CRCERRS);
+ er32(SYMERRS);
+ er32(MPC);
+ er32(SCC);
+ er32(ECOL);
+ er32(MCC);
+ er32(LATECOL);
+ er32(COLC);
+ er32(DC);
+ er32(SEC);
+ er32(RLEC);
+ er32(XONRXC);
+ er32(XONTXC);
+ er32(XOFFRXC);
+ er32(XOFFTXC);
+ er32(FCRUC);
+ er32(GPRC);
+ er32(BPRC);
+ er32(MPRC);
+ er32(GPTC);
+ er32(GORCL);
+ er32(GORCH);
+ er32(GOTCL);
+ er32(GOTCH);
+ er32(RNBC);
+ er32(RUC);
+ er32(RFC);
+ er32(ROC);
+ er32(RJC);
+ er32(TORL);
+ er32(TORH);
+ er32(TOTL);
+ er32(TOTH);
+ er32(TPR);
+ er32(TPT);
+ er32(MPTC);
+ er32(BPTC);
+#endif
+}
+
+/**
+ * e1000e_check_for_copper_link - Check for link (Copper)
+ * @hw: pointer to the HW structure
+ *
+ * Checks to see of the link status of the hardware has changed. If a
+ * change in link status has been detected, then we read the PHY registers
+ * to get the current speed/duplex if link exists.
+ **/
+s32 e1000e_check_for_copper_link(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+ bool link;
+
+ /*
+ * We only want to go out to the PHY registers to see if Auto-Neg
+ * has completed and/or if our link status has changed. The
+ * get_link_status flag is set upon receiving a Link Status
+ * Change or Rx Sequence Error interrupt.
+ */
+ if (!mac->get_link_status) {
+ ret_val = E1000_SUCCESS;
+ goto out;
+ }
+
+ /*
+ * First we want to see if the MII Status Register reports
+ * link. If so, then we want to get the current speed/duplex
+ * of the PHY.
+ */
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link)
+ goto out; /* No link detected */
+
+ mac->get_link_status = false;
+
+ /*
+ * Check if there was DownShift, must be checked
+ * immediately after link-up
+ */
+ e1000e_check_downshift(hw);
+
+ /*
+ * If we are forcing speed/duplex, then we simply return since
+ * we have already determined whether we have link or not.
+ */
+ if (!mac->autoneg) {
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ /*
+ * Auto-Neg is enabled. Auto Speed Detection takes care
+ * of MAC speed/duplex configuration. So we only need to
+ * configure Collision Distance in the MAC.
+ */
+ e1000e_config_collision_dist(hw);
+
+ /*
+ * Configure Flow Control now that Auto-Neg has completed.
+ * First, we need to restore the desired flow control
+ * settings because we may have had to re-autoneg with a
+ * different link partner.
+ */
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ if (ret_val)
+ e_dbg("Error configuring flow control\n");
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_check_for_fiber_link - Check for link (Fiber)
+ * @hw: pointer to the HW structure
+ *
+ * Checks for link up on the hardware. If link is not up and we have
+ * a signal, then we need to force link up.
+ **/
+s32 e1000e_check_for_fiber_link(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 rxcw;
+ u32 ctrl;
+ u32 status;
+ s32 ret_val = E1000_SUCCESS;
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+ rxcw = er32(RXCW);
+
+ /*
+ * If we don't have link (auto-negotiation failed or link partner
+ * cannot auto-negotiate), the cable is plugged in (we have signal),
+ * and our link partner is not trying to auto-negotiate with us (we
+ * are receiving idles or data), we need to force link up. We also
+ * need to give auto-negotiation time to complete, in case the cable
+ * was just plugged in. The autoneg_failed flag does this.
+ */
+ /* (ctrl & E1000_CTRL_SWDPIN1) == 1 == have signal */
+ if ((ctrl & E1000_CTRL_SWDPIN1) && (!(status & E1000_STATUS_LU)) &&
+ (!(rxcw & E1000_RXCW_C))) {
+ if (mac->autoneg_failed == 0) {
+ mac->autoneg_failed = 1;
+ goto out;
+ }
+ e_dbg("NOT RXing /C/, disable AutoNeg and force link.\n");
+
+ /* Disable auto-negotiation in the TXCW register */
+ ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE));
+
+ /* Force link-up and also force full-duplex. */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+ ew32(CTRL, ctrl);
+
+ /* Configure Flow Control after forcing link up. */
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ if (ret_val) {
+ e_dbg("Error configuring flow control\n");
+ goto out;
+ }
+ } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
+ /*
+ * If we are forcing link and we are receiving /C/ ordered
+ * sets, re-enable auto-negotiation in the TXCW register
+ * and disable forced link in the Device Control register
+ * in an attempt to auto-negotiate with our link partner.
+ */
+ e_dbg("RXing /C/, enable AutoNeg and stop forcing link.\n");
+ ew32(TXCW, mac->txcw);
+ ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
+
+ mac->serdes_has_link = true;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_check_for_serdes_link - Check for link (Serdes)
+ * @hw: pointer to the HW structure
+ *
+ * Checks for link up on the hardware. If link is not up and we have
+ * a signal, then we need to force link up.
+ **/
+s32 e1000e_check_for_serdes_link(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 rxcw;
+ u32 ctrl;
+ u32 status;
+ s32 ret_val = E1000_SUCCESS;
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+ rxcw = er32(RXCW);
+
+ /*
+ * If we don't have link (auto-negotiation failed or link partner
+ * cannot auto-negotiate), and our link partner is not trying to
+ * auto-negotiate with us (we are receiving idles or data),
+ * we need to force link up. We also need to give auto-negotiation
+ * time to complete.
+ */
+ /* (ctrl & E1000_CTRL_SWDPIN1) == 1 == have signal */
+ if ((!(status & E1000_STATUS_LU)) && (!(rxcw & E1000_RXCW_C))) {
+ if (mac->autoneg_failed == 0) {
+ mac->autoneg_failed = 1;
+ goto out;
+ }
+ e_dbg("NOT RXing /C/, disable AutoNeg and force link.\n");
+
+ /* Disable auto-negotiation in the TXCW register */
+ ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE));
+
+ /* Force link-up and also force full-duplex. */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+ ew32(CTRL, ctrl);
+
+ /* Configure Flow Control after forcing link up. */
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ if (ret_val) {
+ e_dbg("Error configuring flow control\n");
+ goto out;
+ }
+ } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
+ /*
+ * If we are forcing link and we are receiving /C/ ordered
+ * sets, re-enable auto-negotiation in the TXCW register
+ * and disable forced link in the Device Control register
+ * in an attempt to auto-negotiate with our link partner.
+ */
+ e_dbg("RXing /C/, enable AutoNeg and stop forcing link.\n");
+ ew32(TXCW, mac->txcw);
+ ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
+
+ mac->serdes_has_link = true;
+ } else if (!(E1000_TXCW_ANE & er32(TXCW))) {
+ /*
+ * If we force link for non-auto-negotiation switch, check
+ * link status based on MAC synchronization for internal
+ * serdes media type.
+ */
+ /* SYNCH bit and IV bit are sticky. */
+ udelay(10);
+ rxcw = er32(RXCW);
+ if (rxcw & E1000_RXCW_SYNCH) {
+ if (!(rxcw & E1000_RXCW_IV)) {
+ mac->serdes_has_link = true;
+ e_dbg("SERDES: Link up - forced.\n");
+ }
+ } else {
+ mac->serdes_has_link = false;
+ e_dbg("SERDES: Link down - force failed.\n");
+ }
+ }
+
+ if (E1000_TXCW_ANE & er32(TXCW)) {
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU) {
+ /* SYNCH bit and IV bit are sticky, so reread rxcw. */
+ udelay(10);
+ rxcw = er32(RXCW);
+ if (rxcw & E1000_RXCW_SYNCH) {
+ if (!(rxcw & E1000_RXCW_IV)) {
+ mac->serdes_has_link = true;
+ e_dbg("SERDES: Link up - autoneg "
+ "completed sucessfully.\n");
+ } else {
+ mac->serdes_has_link = false;
+ e_dbg("SERDES: Link down - invalid"
+ "codewords detected in autoneg.\n");
+ }
+ } else {
+ mac->serdes_has_link = false;
+ e_dbg("SERDES: Link down - no sync.\n");
+ }
+ } else {
+ mac->serdes_has_link = false;
+ e_dbg("SERDES: Link down - autoneg failed\n");
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_setup_link - Setup flow control and link settings
+ * @hw: pointer to the HW structure
+ *
+ * Determines which flow control settings to use, then configures flow
+ * control. Calls the appropriate media-specific link configuration
+ * function. Assuming the adapter has a valid link partner, a valid link
+ * should be established. Assumes the hardware has previously been reset
+ * and the transmitter and receiver are not enabled.
+ **/
+s32 e1000e_setup_link(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ /*
+ * In the case of the phy reset being blocked, we already have a link.
+ * We do not need to set it up again.
+ */
+ if (hw->phy.ops.check_reset_block)
+ if (e1000e_check_reset_block(hw))
+ goto out;
+
+ /*
+ * If requested flow control is set to default, set flow control
+ * based on the EEPROM flow control settings.
+ */
+ if (hw->fc.requested_mode == e1000_fc_default) {
+ ret_val = e1000e_set_default_fc_generic(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ /*
+ * Save off the requested flow control mode for use later. Depending
+ * on the link partner's capabilities, we may or may not use this mode.
+ */
+ hw->fc.current_mode = hw->fc.requested_mode;
+
+ e_dbg("After fix-ups FlowControl is now = %x\n",
+ hw->fc.current_mode);
+
+ /* Call the necessary media_type subroutine to configure the link. */
+ ret_val = hw->mac.ops.setup_physical_interface(hw);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Initialize the flow control address, type, and PAUSE timer
+ * registers to their default values. This is done even if flow
+ * control is disabled, because it does not hurt anything to
+ * initialize these registers.
+ */
+ e_dbg("Initializing the Flow Control address, type and timer regs\n");
+ ew32(FCT, FLOW_CONTROL_TYPE);
+ ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+ ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW);
+
+ ew32(FCTTV, hw->fc.pause_time);
+
+ ret_val = e1000e_set_fc_watermarks(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_setup_fiber_serdes_link - Setup link for fiber/serdes
+ * @hw: pointer to the HW structure
+ *
+ * Configures collision distance and flow control for fiber and serdes
+ * links. Upon successful setup, poll for link.
+ **/
+s32 e1000e_setup_fiber_serdes_link(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val = E1000_SUCCESS;
+
+ ctrl = er32(CTRL);
+
+ /* Take the link out of reset */
+ ctrl &= ~E1000_CTRL_LRST;
+
+ e1000e_config_collision_dist(hw);
+
+ ret_val = e1000e_commit_fc_settings_generic(hw);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Since auto-negotiation is enabled, take the link out of reset (the
+ * link will be in reset, because we previously reset the chip). This
+ * will restart auto-negotiation. If auto-negotiation is successful
+ * then the link-up status bit will be set and the flow control enable
+ * bits (RFCE and TFCE) will be set according to their negotiated value.
+ */
+ e_dbg("Auto-negotiation enabled\n");
+
+ ew32(CTRL, ctrl);
+ e1e_flush();
+ msleep(1);
+
+ /*
+ * For these adapters, the SW definable pin 1 is set when the optics
+ * detect a signal. If we have a signal, then poll for a "Link-Up"
+ * indication.
+ */
+ if (hw->phy.media_type == e1000_media_type_internal_serdes ||
+ (er32(CTRL) & E1000_CTRL_SWDPIN1)) {
+ ret_val = e1000e_poll_fiber_serdes_link_generic(hw);
+ } else {
+ e_dbg("No signal detected\n");
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_config_collision_dist - Configure collision distance
+ * @hw: pointer to the HW structure
+ *
+ * Configures the collision distance to the default value and is used
+ * during link setup. Currently no func pointer exists and all
+ * implementations are handled in the generic version of this function.
+ **/
+void e1000e_config_collision_dist(struct e1000_hw *hw)
+{
+ u32 tctl;
+
+ tctl = er32(TCTL);
+
+ tctl &= ~E1000_TCTL_COLD;
+ tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT;
+
+ ew32(TCTL, tctl);
+ e1e_flush();
+}
+
+/**
+ * e1000e_poll_fiber_serdes_link_generic - Poll for link up
+ * @hw: pointer to the HW structure
+ *
+ * Polls for link up by reading the status register, if link fails to come
+ * up with auto-negotiation, then the link is forced if a signal is detected.
+ **/
+static s32 e1000e_poll_fiber_serdes_link_generic(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 i, status;
+ s32 ret_val = E1000_SUCCESS;
+
+ /*
+ * If we have a signal (the cable is plugged in, or assumed true for
+ * serdes media) then poll for a "Link-Up" indication in the Device
+ * Status Register. Time-out if a link isn't seen in 500 milliseconds
+ * seconds (Auto-negotiation should complete in less than 500
+ * milliseconds even if the other end is doing it in SW).
+ */
+ for (i = 0; i < FIBER_LINK_UP_LIMIT; i++) {
+ msleep(10);
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU)
+ break;
+ }
+ if (i == FIBER_LINK_UP_LIMIT) {
+ e_dbg("Never got a valid link from auto-neg!!!\n");
+ mac->autoneg_failed = 1;
+ /*
+ * AutoNeg failed to achieve a link, so we'll call
+ * mac->check_for_link. This routine will force the
+ * link up if we detect a signal. This will allow us to
+ * communicate with non-autonegotiating link partners.
+ */
+ ret_val = hw->mac.ops.check_for_link(hw);
+ if (ret_val) {
+ e_dbg("Error while checking for link\n");
+ goto out;
+ }
+ mac->autoneg_failed = 0;
+ } else {
+ mac->autoneg_failed = 0;
+ e_dbg("Valid Link Found\n");
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_commit_fc_settings_generic - Configure flow control
+ * @hw: pointer to the HW structure
+ *
+ * Write the flow control settings to the Transmit Config Word Register (TXCW)
+ * base on the flow control settings in e1000_mac_info.
+ **/
+static s32 e1000e_commit_fc_settings_generic(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 txcw;
+ s32 ret_val = E1000_SUCCESS;
+
+ /*
+ * Check for a software override of the flow control settings, and
+ * setup the device accordingly. If auto-negotiation is enabled, then
+ * software will have to set the "PAUSE" bits to the correct value in
+ * the Transmit Config Word Register (TXCW) and re-start auto-
+ * negotiation. However, if auto-negotiation is disabled, then
+ * software will have to manually configure the two flow control enable
+ * bits in the CTRL register.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but we
+ * do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ */
+ switch (hw->fc.current_mode) {
+ case e1000_fc_none:
+ /* Flow control completely disabled by a software over-ride. */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
+ break;
+ case e1000_fc_rx_pause:
+ /*
+ * Rx Flow control is enabled and Tx Flow control is disabled
+ * by a software over-ride. Since there really isn't a way to
+ * advertise that we are capable of Rx Pause ONLY, we will
+ * advertise that we support both symmetric and asymmetric RX
+ * PAUSE. Later, we will disable the adapter's ability to send
+ * PAUSE frames.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+ break;
+ case e1000_fc_tx_pause:
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is disabled,
+ * by a software over-ride.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
+ break;
+ case e1000_fc_full:
+ /*
+ * Flow control (both Rx and Tx) is enabled by a software
+ * over-ride.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+ break;
+ default:
+ e_dbg("Flow control param set incorrectly\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ break;
+ }
+
+ ew32(TXCW, txcw);
+ mac->txcw = txcw;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_set_fc_watermarks - Set flow control high/low watermarks
+ * @hw: pointer to the HW structure
+ *
+ * Sets the flow control high/low threshold (watermark) registers. If
+ * flow control XON frame transmission is enabled, then set XON frame
+ * transmission as well.
+ **/
+s32 e1000e_set_fc_watermarks(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u32 fcrtl = 0, fcrth = 0;
+
+ /*
+ * Set the flow control receive threshold registers. Normally,
+ * these registers will be set to a default threshold that may be
+ * adjusted later by the driver's runtime code. However, if the
+ * ability to transmit pause frames is not enabled, then these
+ * registers will be set to 0.
+ */
+ if (hw->fc.current_mode & e1000_fc_tx_pause) {
+ /*
+ * We need to set up the Receive Threshold high and low water
+ * marks as well as (optionally) enabling the transmission of
+ * XON frames.
+ */
+ fcrtl = hw->fc.low_water;
+ if (hw->fc.send_xon)
+ fcrtl |= E1000_FCRTL_XONE;
+
+ fcrth = hw->fc.high_water;
+ }
+ ew32(FCRTL, fcrtl);
+ ew32(FCRTH, fcrth);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_set_default_fc_generic - Set flow control default values
+ * @hw: pointer to the HW structure
+ *
+ * Read the EEPROM for the default values for flow control and store the
+ * values.
+ **/
+static s32 e1000e_set_default_fc_generic(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 nvm_data;
+
+ /*
+ * Read and store word 0x0F of the EEPROM. This word contains bits
+ * that determine the hardware's default PAUSE (flow control) mode,
+ * a bit that determines whether the HW defaults to enabling or
+ * disabling auto-negotiation, and the direction of the
+ * SW defined pins. If there is no SW over-ride of the flow
+ * control setting, then the variable hw->fc will
+ * be initialized based on a value in the EEPROM.
+ */
+ ret_val = e1000e_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &nvm_data);
+
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ goto out;
+ }
+
+ if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 0)
+ hw->fc.requested_mode = e1000_fc_none;
+ else if ((nvm_data & NVM_WORD0F_PAUSE_MASK) ==
+ NVM_WORD0F_ASM_DIR)
+ hw->fc.requested_mode = e1000_fc_tx_pause;
+ else
+ hw->fc.requested_mode = e1000_fc_full;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_force_mac_fc - Force the MAC's flow control settings
+ * @hw: pointer to the HW structure
+ *
+ * Force the MAC's flow control settings. Sets the TFCE and RFCE bits in the
+ * device control register to reflect the adapter settings. TFCE and RFCE
+ * need to be explicitly set by software when a copper PHY is used because
+ * autonegotiation is managed by the PHY rather than the MAC. Software must
+ * also configure these bits when link is forced on a fiber connection.
+ **/
+s32 e1000e_force_mac_fc(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val = E1000_SUCCESS;
+
+ ctrl = er32(CTRL);
+
+ /*
+ * Because we didn't get link via the internal auto-negotiation
+ * mechanism (we either forced link or we got link via PHY
+ * auto-neg), we have to manually enable/disable transmit an
+ * receive flow control.
+ *
+ * The "Case" statement below enables/disable flow control
+ * according to the "hw->fc.current_mode" parameter.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause
+ * frames but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * frames but we do not receive pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) is enabled.
+ * other: No other values should be possible at this point.
+ */
+ e_dbg("hw->fc.current_mode = %u\n", hw->fc.current_mode);
+
+ switch (hw->fc.current_mode) {
+ case e1000_fc_none:
+ ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
+ break;
+ case e1000_fc_rx_pause:
+ ctrl &= (~E1000_CTRL_TFCE);
+ ctrl |= E1000_CTRL_RFCE;
+ break;
+ case e1000_fc_tx_pause:
+ ctrl &= (~E1000_CTRL_RFCE);
+ ctrl |= E1000_CTRL_TFCE;
+ break;
+ case e1000_fc_full:
+ ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
+ break;
+ default:
+ e_dbg("Flow control param set incorrectly\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ ew32(CTRL, ctrl);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_config_fc_after_link_up - Configures flow control after link
+ * @hw: pointer to the HW structure
+ *
+ * Checks the status of auto-negotiation after link up to ensure that the
+ * speed and duplex were not forced. If the link needed to be forced, then
+ * flow control needs to be forced also. If auto-negotiation is enabled
+ * and did not fail, then we configure flow control based on our link
+ * partner.
+ **/
+s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val = E1000_SUCCESS;
+ u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg;
+ u16 speed, duplex;
+
+ /*
+ * Check for the case where we have fiber media and auto-neg failed
+ * so we had to force link. In this case, we need to force the
+ * configuration of the MAC to match the "fc" parameter.
+ */
+ if (mac->autoneg_failed) {
+ if (hw->phy.media_type == e1000_media_type_fiber ||
+ hw->phy.media_type == e1000_media_type_internal_serdes)
+ ret_val = e1000e_force_mac_fc(hw);
+ } else {
+ if (hw->phy.media_type == e1000_media_type_copper)
+ ret_val = e1000e_force_mac_fc(hw);
+ }
+
+ if (ret_val) {
+ e_dbg("Error forcing flow control settings\n");
+ goto out;
+ }
+
+ /*
+ * Check for the case where we have copper media and auto-neg is
+ * enabled. In this case, we need to check and see if Auto-Neg
+ * has completed, and if so, how the PHY and link partner has
+ * flow control configured.
+ */
+ if ((hw->phy.media_type == e1000_media_type_copper) && mac->autoneg) {
+ /*
+ * Read the MII Status Register and check to see if AutoNeg
+ * has completed. We read this twice because this reg has
+ * some "sticky" (latched) bits.
+ */
+ ret_val = e1e_rphy(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ goto out;
+ ret_val = e1e_rphy(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ goto out;
+
+ if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) {
+ e_dbg("Copper PHY and Auto Neg "
+ "has not completed.\n");
+ goto out;
+ }
+
+ /*
+ * The AutoNeg process has completed, so we now need to
+ * read both the Auto Negotiation Advertisement
+ * Register (Address 4) and the Auto_Negotiation Base
+ * Page Ability Register (Address 5) to determine how
+ * flow control was negotiated.
+ */
+ ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV,
+ &mii_nway_adv_reg);
+ if (ret_val)
+ goto out;
+ ret_val = e1e_rphy(hw, PHY_LP_ABILITY,
+ &mii_nway_lp_ability_reg);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Two bits in the Auto Negotiation Advertisement Register
+ * (Address 4) and two bits in the Auto Negotiation Base
+ * Page Ability Register (Address 5) determine flow control
+ * for both the PHY and the link partner. The following
+ * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+ * 1999, describes these PAUSE resolution bits and how flow
+ * control is determined based upon these settings.
+ * NOTE: DC = Don't Care
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+ *-------|---------|-------|---------|--------------------
+ * 0 | 0 | DC | DC | e1000_fc_none
+ * 0 | 1 | 0 | DC | e1000_fc_none
+ * 0 | 1 | 1 | 0 | e1000_fc_none
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ * 1 | 0 | 0 | DC | e1000_fc_none
+ * 1 | DC | 1 | DC | e1000_fc_full
+ * 1 | 1 | 0 | 0 | e1000_fc_none
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ *
+ * Are both PAUSE bits set to 1? If so, this implies
+ * Symmetric Flow Control is enabled at both ends. The
+ * ASM_DIR bits are irrelevant per the spec.
+ *
+ * For Symmetric Flow Control:
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | DC | 1 | DC | E1000_fc_full
+ *
+ */
+ if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+ /*
+ * Now we need to check if the user selected Rx ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == e1000_fc_full) {
+ hw->fc.current_mode = e1000_fc_full;
+ e_dbg("Flow Control = FULL.\r\n");
+ } else {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ e_dbg("Flow Control = "
+ "RX PAUSE frames only.\r\n");
+ }
+ }
+ /*
+ * For receiving PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ */
+ else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ hw->fc.current_mode = e1000_fc_tx_pause;
+ e_dbg("Flow Control = TX PAUSE frames only.\r\n");
+ }
+ /*
+ * For transmitting PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ */
+ else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ e_dbg("Flow Control = RX PAUSE frames only.\r\n");
+ } else {
+ /*
+ * Per the IEEE spec, at this point flow control
+ * should be disabled.
+ */
+ hw->fc.current_mode = e1000_fc_none;
+ e_dbg("Flow Control = NONE.\r\n");
+ }
+
+ /*
+ * Now we need to do one last check... If we auto-
+ * negotiated to HALF DUPLEX, flow control should not be
+ * enabled per IEEE 802.3 spec.
+ */
+ ret_val = mac->ops.get_link_up_info(hw, &speed, &duplex);
+ if (ret_val) {
+ e_dbg("Error getting link speed and duplex\n");
+ goto out;
+ }
+
+ if (duplex == HALF_DUPLEX)
+ hw->fc.current_mode = e1000_fc_none;
+
+ /*
+ * Now we call a subroutine to actually force the MAC
+ * controller to use the correct flow control settings.
+ */
+ ret_val = e1000e_force_mac_fc(hw);
+ if (ret_val) {
+ e_dbg("Error forcing flow control settings\n");
+ goto out;
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_get_speed_and_duplex_copper - Retrieve current speed/duplex
+ * @hw: pointer to the HW structure
+ * @speed: stores the current speed
+ * @duplex: stores the current duplex
+ *
+ * Read the status register for the current speed/duplex and store the current
+ * speed and duplex for copper connections.
+ **/
+s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex)
+{
+ u32 status;
+
+ status = er32(STATUS);
+ if (status & E1000_STATUS_SPEED_1000) {
+ *speed = SPEED_1000;
+ e_dbg("1000 Mbs, ");
+ } else if (status & E1000_STATUS_SPEED_100) {
+ *speed = SPEED_100;
+ e_dbg("100 Mbs, ");
+ } else {
+ *speed = SPEED_10;
+ e_dbg("10 Mbs, ");
+ }
+
+ if (status & E1000_STATUS_FD) {
+ *duplex = FULL_DUPLEX;
+ e_dbg("Full Duplex\n");
+ } else {
+ *duplex = HALF_DUPLEX;
+ e_dbg("Half Duplex\n");
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_get_speed_and_duplex_fiber_generic - Retrieve current speed/duplex
+ * @hw: pointer to the HW structure
+ * @speed: stores the current speed
+ * @duplex: stores the current duplex
+ *
+ * Sets the speed and duplex to gigabit full duplex (the only possible option)
+ * for fiber/serdes links.
+ **/
+s32 e1000e_get_speed_and_duplex_fiber_serdes(struct e1000_hw *hw __unused,
+ u16 *speed, u16 *duplex)
+{
+ *speed = SPEED_1000;
+ *duplex = FULL_DUPLEX;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_get_hw_semaphore - Acquire hardware semaphore
+ * @hw: pointer to the HW structure
+ *
+ * Acquire the HW semaphore to access the PHY or NVM
+ **/
+s32 e1000e_get_hw_semaphore(struct e1000_hw *hw)
+{
+ u32 swsm;
+ s32 ret_val = E1000_SUCCESS;
+ s32 timeout = hw->nvm.word_size + 1;
+ s32 i = 0;
+
+ /* Get the SW semaphore */
+ while (i < timeout) {
+ swsm = er32(SWSM);
+ if (!(swsm & E1000_SWSM_SMBI))
+ break;
+
+ udelay(50);
+ i++;
+ }
+
+ if (i == timeout) {
+ e_dbg("Driver can't access device - SMBI bit is set.\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+ /* Get the FW semaphore. */
+ for (i = 0; i < timeout; i++) {
+ swsm = er32(SWSM);
+ ew32(SWSM, swsm | E1000_SWSM_SWESMBI);
+
+ /* Semaphore acquired if bit latched */
+ if (er32(SWSM) & E1000_SWSM_SWESMBI)
+ break;
+
+ udelay(50);
+ }
+
+ if (i == timeout) {
+ /* Release semaphores */
+ e1000e_put_hw_semaphore(hw);
+ e_dbg("Driver can't access the NVM\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_put_hw_semaphore - Release hardware semaphore
+ * @hw: pointer to the HW structure
+ *
+ * Release hardware semaphore used to access the PHY or NVM
+ **/
+void e1000e_put_hw_semaphore(struct e1000_hw *hw)
+{
+ u32 swsm;
+
+ swsm = er32(SWSM);
+ swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
+ ew32(SWSM, swsm);
+}
+/**
+ * e1000e_get_auto_rd_done - Check for auto read completion
+ * @hw: pointer to the HW structure
+ *
+ * Check EEPROM for Auto Read done bit.
+ **/
+s32 e1000e_get_auto_rd_done(struct e1000_hw *hw)
+{
+ s32 i = 0;
+ s32 ret_val = E1000_SUCCESS;
+
+ while (i < AUTO_READ_DONE_TIMEOUT) {
+ if (er32(EECD) & E1000_EECD_AUTO_RD)
+ break;
+ msleep(1);
+ i++;
+ }
+
+ if (i == AUTO_READ_DONE_TIMEOUT) {
+ e_dbg("Auto read by HW from NVM has not completed.\n");
+ ret_val = -E1000_ERR_RESET;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_valid_led_default - Verify a valid default LED config
+ * @hw: pointer to the HW structure
+ * @data: pointer to the NVM (EEPROM)
+ *
+ * Read the EEPROM for the current default LED configuration. If the
+ * LED configuration is not valid, set to a valid LED configuration.
+ **/
+s32 e1000e_valid_led_default(struct e1000_hw *hw, u16 *data)
+{
+ s32 ret_val;
+
+ ret_val = e1000e_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ goto out;
+ }
+
+ if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF)
+ *data = ID_LED_DEFAULT;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_id_led_init -
+ * @hw: pointer to the HW structure
+ *
+ **/
+s32 e1000e_id_led_init(struct e1000_hw *hw __unused)
+{
+#if 0
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+ const u32 ledctl_mask = 0x000000FF;
+ const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON;
+ const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF;
+ u16 data, i, temp;
+ const u16 led_mask = 0x0F;
+
+ ret_val = hw->nvm.ops.valid_led_default(hw, &data);
+ if (ret_val)
+ goto out;
+
+ mac->ledctl_default = er32(LEDCTL);
+ mac->ledctl_mode1 = mac->ledctl_default;
+ mac->ledctl_mode2 = mac->ledctl_default;
+
+ for (i = 0; i < 4; i++) {
+ temp = (data >> (i << 2)) & led_mask;
+ switch (temp) {
+ case ID_LED_ON1_DEF2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_ON1_OFF2:
+ mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode1 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_OFF1_DEF2:
+ case ID_LED_OFF1_ON2:
+ case ID_LED_OFF1_OFF2:
+ mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode1 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ switch (temp) {
+ case ID_LED_DEF1_ON2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_OFF1_ON2:
+ mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode2 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_DEF1_OFF2:
+ case ID_LED_ON1_OFF2:
+ case ID_LED_OFF1_OFF2:
+ mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode2 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ }
+
+out:
+ return ret_val;
+#endif
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_setup_led_generic - Configures SW controllable LED
+ * @hw: pointer to the HW structure
+ *
+ * This prepares the SW controllable LED for use and saves the current state
+ * of the LED so it can be later restored.
+ **/
+s32 e1000e_setup_led_generic(struct e1000_hw *hw __unused)
+{
+#if 0
+ u32 ledctl;
+ s32 ret_val = E1000_SUCCESS;
+
+ if (hw->mac.ops.setup_led != e1000e_setup_led_generic) {
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ if (hw->phy.media_type == e1000_media_type_fiber) {
+ ledctl = er32(LEDCTL);
+ hw->mac.ledctl_default = ledctl;
+ /* Turn off LED0 */
+ ledctl &= ~(E1000_LEDCTL_LED0_IVRT |
+ E1000_LEDCTL_LED0_BLINK |
+ E1000_LEDCTL_LED0_MODE_MASK);
+ ledctl |= (E1000_LEDCTL_MODE_LED_OFF <<
+ E1000_LEDCTL_LED0_MODE_SHIFT);
+ ew32(LEDCTL, ledctl);
+ } else if (hw->phy.media_type == e1000_media_type_copper) {
+ ew32(LEDCTL, hw->mac.ledctl_mode1);
+ }
+
+out:
+ return ret_val;
+#endif
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_cleanup_led_generic - Set LED config to default operation
+ * @hw: pointer to the HW structure
+ *
+ * Remove the current LED configuration and set the LED configuration
+ * to the default value, saved from the EEPROM.
+ **/
+s32 e1000e_cleanup_led_generic(struct e1000_hw *hw __unused)
+{
+#if 0
+ s32 ret_val = E1000_SUCCESS;
+
+ if (hw->mac.ops.cleanup_led != e1000e_cleanup_led_generic) {
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ ew32(LEDCTL, hw->mac.ledctl_default);
+
+out:
+ return ret_val;
+#endif
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_blink_led - Blink LED
+ * @hw: pointer to the HW structure
+ *
+ * Blink the LEDs which are set to be on.
+ **/
+s32 e1000e_blink_led(struct e1000_hw *hw __unused)
+{
+#if 0
+ u32 ledctl_blink = 0;
+ u32 i;
+
+ if (hw->phy.media_type == e1000_media_type_fiber) {
+ /* always blink LED0 for PCI-E fiber */
+ ledctl_blink = E1000_LEDCTL_LED0_BLINK |
+ (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT);
+ } else {
+ /*
+ * set the blink bit for each LED that's "on" (0x0E)
+ * in ledctl_mode2
+ */
+ ledctl_blink = hw->mac.ledctl_mode2;
+ for (i = 0; i < 4; i++)
+ if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
+ E1000_LEDCTL_MODE_LED_ON)
+ ledctl_blink |= (E1000_LEDCTL_LED0_BLINK <<
+ (i * 8));
+ }
+
+ ew32(LEDCTL, ledctl_blink);
+#endif
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_led_on_generic - Turn LED on
+ * @hw: pointer to the HW structure
+ *
+ * Turn LED on.
+ **/
+s32 e1000e_led_on_generic(struct e1000_hw *hw __unused)
+{
+#if 0
+ u32 ctrl;
+
+ switch (hw->phy.media_type) {
+ case e1000_media_type_fiber:
+ ctrl = er32(CTRL);
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ ew32(CTRL, ctrl);
+ break;
+ case e1000_media_type_copper:
+ ew32(LEDCTL, hw->mac.ledctl_mode2);
+ break;
+ default:
+ break;
+ }
+#endif
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_led_off_generic - Turn LED off
+ * @hw: pointer to the HW structure
+ *
+ * Turn LED off.
+ **/
+s32 e1000e_led_off_generic(struct e1000_hw *hw __unused)
+{
+#if 0
+ u32 ctrl;
+
+ switch (hw->phy.media_type) {
+ case e1000_media_type_fiber:
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ ew32(CTRL, ctrl);
+ break;
+ case e1000_media_type_copper:
+ ew32(LEDCTL, hw->mac.ledctl_mode1);
+ break;
+ default:
+ break;
+ }
+#endif
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_set_pcie_no_snoop - Set PCI-express capabilities
+ * @hw: pointer to the HW structure
+ * @no_snoop: bitmap of snoop events
+ *
+ * Set the PCI-express register to snoop for events enabled in 'no_snoop'.
+ **/
+void e1000e_set_pcie_no_snoop(struct e1000_hw *hw, u32 no_snoop)
+{
+ u32 gcr;
+
+ if (hw->bus.type != e1000_bus_type_pci_express)
+ goto out;
+
+ if (no_snoop) {
+ gcr = er32(GCR);
+ gcr &= ~(PCIE_NO_SNOOP_ALL);
+ gcr |= no_snoop;
+ ew32(GCR, gcr);
+ }
+out:
+ return;
+}
+
+/**
+ * e1000e_disable_pcie_master - Disables PCI-express master access
+ * @hw: pointer to the HW structure
+ *
+ * Returns 0 (E1000_SUCCESS) if successful, else returns -10
+ * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused
+ * the master requests to be disabled.
+ *
+ * Disables PCI-Express master access and verifies there are no pending
+ * requests.
+ **/
+s32 e1000e_disable_pcie_master(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 timeout = MASTER_DISABLE_TIMEOUT;
+ s32 ret_val = E1000_SUCCESS;
+
+ if (hw->bus.type != e1000_bus_type_pci_express)
+ goto out;
+
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_GIO_MASTER_DISABLE;
+ ew32(CTRL, ctrl);
+
+ while (timeout) {
+ if (!(er32(STATUS) &
+ E1000_STATUS_GIO_MASTER_ENABLE))
+ break;
+ udelay(100);
+ timeout--;
+ }
+
+ if (!timeout) {
+ e_dbg("Master requests are pending.\n");
+ ret_val = -E1000_ERR_MASTER_REQUESTS_PENDING;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_reset_adaptive - Reset Adaptive Interframe Spacing
+ * @hw: pointer to the HW structure
+ *
+ * Reset the Adaptive Interframe Spacing throttle to default values.
+ **/
+void e1000e_reset_adaptive(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+
+ if (!mac->adaptive_ifs) {
+ e_dbg("Not in Adaptive IFS mode!\n");
+ goto out;
+ }
+
+ mac->current_ifs_val = 0;
+ mac->ifs_min_val = IFS_MIN;
+ mac->ifs_max_val = IFS_MAX;
+ mac->ifs_step_size = IFS_STEP;
+ mac->ifs_ratio = IFS_RATIO;
+
+ mac->in_ifs_mode = false;
+ ew32(AIT, 0);
+out:
+ return;
+}
+
+/**
+ * e1000e_update_adaptive - Update Adaptive Interframe Spacing
+ * @hw: pointer to the HW structure
+ *
+ * Update the Adaptive Interframe Spacing Throttle value based on the
+ * time between transmitted packets and time between collisions.
+ **/
+void e1000e_update_adaptive(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+
+ if (!mac->adaptive_ifs) {
+ e_dbg("Not in Adaptive IFS mode!\n");
+ goto out;
+ }
+
+ if ((mac->collision_delta * mac->ifs_ratio) > mac->tx_packet_delta) {
+ if (mac->tx_packet_delta > MIN_NUM_XMITS) {
+ mac->in_ifs_mode = true;
+ if (mac->current_ifs_val < mac->ifs_max_val) {
+ if (!mac->current_ifs_val)
+ mac->current_ifs_val = mac->ifs_min_val;
+ else
+ mac->current_ifs_val +=
+ mac->ifs_step_size;
+ ew32(AIT, mac->current_ifs_val);
+ }
+ }
+ } else {
+ if (mac->in_ifs_mode &&
+ (mac->tx_packet_delta <= MIN_NUM_XMITS)) {
+ mac->current_ifs_val = 0;
+ mac->in_ifs_mode = false;
+ ew32(AIT, 0);
+ }
+ }
+out:
+ return;
+}
+
+/**
+ * e1000e_validate_mdi_setting_generic - Verify MDI/MDIx settings
+ * @hw: pointer to the HW structure
+ *
+ * Verify that when not using auto-negotiation that MDI/MDIx is correctly
+ * set, which is forced to MDI mode only.
+ **/
+static s32 e1000e_validate_mdi_setting_generic(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ if (!hw->mac.autoneg && (hw->phy.mdix == 0 || hw->phy.mdix == 3)) {
+ e_dbg("Invalid MDI setting detected\n");
+ hw->phy.mdix = 1;
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#ifndef _E1000E_MAC_H_
+#define _E1000E_MAC_H_
+
+/*
+ * Functions that should not be called directly from drivers but can be used
+ * by other files in this 'shared code'
+ */
+void e1000e_init_mac_ops_generic(struct e1000_hw *hw);
+s32 e1000e_blink_led(struct e1000_hw *hw);
+s32 e1000e_check_for_copper_link(struct e1000_hw *hw);
+s32 e1000e_check_for_fiber_link(struct e1000_hw *hw);
+s32 e1000e_check_for_serdes_link(struct e1000_hw *hw);
+s32 e1000e_cleanup_led_generic(struct e1000_hw *hw);
+s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw);
+s32 e1000e_disable_pcie_master(struct e1000_hw *hw);
+s32 e1000e_force_mac_fc(struct e1000_hw *hw);
+s32 e1000e_get_auto_rd_done(struct e1000_hw *hw);
+s32 e1000e_get_bus_info_pcie(struct e1000_hw *hw);
+void e1000e_set_lan_id_single_port(struct e1000_hw *hw);
+s32 e1000e_get_hw_semaphore(struct e1000_hw *hw);
+s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex);
+s32 e1000e_get_speed_and_duplex_fiber_serdes(struct e1000_hw *hw,
+ u16 *speed, u16 *duplex);
+s32 e1000e_id_led_init(struct e1000_hw *hw);
+s32 e1000e_led_on_generic(struct e1000_hw *hw);
+s32 e1000e_led_off_generic(struct e1000_hw *hw);
+void e1000e_update_mc_addr_list_generic(struct e1000_hw *hw,
+ u8 *mc_addr_list, u32 mc_addr_count);
+s32 e1000e_set_fc_watermarks(struct e1000_hw *hw);
+s32 e1000e_setup_fiber_serdes_link(struct e1000_hw *hw);
+s32 e1000e_setup_led_generic(struct e1000_hw *hw);
+s32 e1000e_setup_link(struct e1000_hw *hw);
+
+void e1000e_clear_hw_cntrs_base(struct e1000_hw *hw);
+void e1000e_clear_vfta_generic(struct e1000_hw *hw);
+void e1000e_config_collision_dist(struct e1000_hw *hw);
+void e1000e_init_rx_addrs(struct e1000_hw *hw, u16 rar_count);
+void e1000e_mta_set_generic(struct e1000_hw *hw, u32 hash_value);
+void e1000e_pcix_mmrbc_workaround_generic(struct e1000_hw *hw);
+void e1000e_put_hw_semaphore(struct e1000_hw *hw);
+void e1000e_rar_set(struct e1000_hw *hw, u8 *addr, u32 index);
+s32 e1000e_check_alt_mac_addr_generic(struct e1000_hw *hw);
+void e1000e_reset_adaptive(struct e1000_hw *hw);
+void e1000e_set_pcie_no_snoop(struct e1000_hw *hw, u32 no_snoop);
+void e1000e_update_adaptive(struct e1000_hw *hw);
+void e1000e_write_vfta_generic(struct e1000_hw *hw, u32 offset, u32 value);
+
+#endif
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ Portions Copyright(c) 2010 Marty Connor <mdc@etherboot.org>
+ Portions Copyright(c) 2010 Entity Cyber, Inc.
+ Portions Copyright(c) 2010 Northrop Grumman Corporation
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#include "e1000e.h"
+
+static s32 e1000e_get_variants_82571(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ static int global_quad_port_a; /* global port a indication */
+ struct pci_device *pdev = adapter->pdev;
+ u16 eeprom_data = 0;
+ int is_port_b = er32(STATUS) & E1000_STATUS_FUNC_1;
+
+ /* tag quad port adapters first, it's used below */
+ switch (pdev->device) {
+ case E1000_DEV_ID_82571EB_QUAD_COPPER:
+ case E1000_DEV_ID_82571EB_QUAD_FIBER:
+ case E1000_DEV_ID_82571EB_QUAD_COPPER_LP:
+ case E1000_DEV_ID_82571PT_QUAD_COPPER:
+ adapter->flags |= FLAG_IS_QUAD_PORT;
+ /* mark the first port */
+ if (global_quad_port_a == 0)
+ adapter->flags |= FLAG_IS_QUAD_PORT_A;
+ /* Reset for multiple quad port adapters */
+ global_quad_port_a++;
+ if (global_quad_port_a == 4)
+ global_quad_port_a = 0;
+ break;
+ default:
+ break;
+ }
+
+ switch (adapter->hw.mac.type) {
+ case e1000_82571:
+ /* these dual ports don't have WoL on port B at all */
+ if (((pdev->device == E1000_DEV_ID_82571EB_FIBER) ||
+ (pdev->device == E1000_DEV_ID_82571EB_SERDES) ||
+ (pdev->device == E1000_DEV_ID_82571EB_COPPER)) &&
+ (is_port_b))
+ adapter->flags &= ~FLAG_HAS_WOL;
+ /* quad ports only support WoL on port A */
+ if (adapter->flags & FLAG_IS_QUAD_PORT &&
+ (!(adapter->flags & FLAG_IS_QUAD_PORT_A)))
+ adapter->flags &= ~FLAG_HAS_WOL;
+ /* Does not support WoL on any port */
+ if (pdev->device == E1000_DEV_ID_82571EB_SERDES_QUAD)
+ adapter->flags &= ~FLAG_HAS_WOL;
+ break;
+
+ case e1000_82573:
+ if (pdev->device == E1000_DEV_ID_82573L) {
+ if (e1000e_read_nvm(&adapter->hw, NVM_INIT_3GIO_3, 1,
+ &eeprom_data) < 0)
+ break;
+ if (!(eeprom_data & NVM_WORD1A_ASPM_MASK)) {
+ adapter->flags |= FLAG_HAS_JUMBO_FRAMES;
+ adapter->max_hw_frame_size = DEFAULT_JUMBO;
+ }
+ }
+ break;
+
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+static struct e1000_info e1000_82571_info = {
+ .mac = e1000_82571,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_HAS_SMART_POWER_DOWN
+ | FLAG_RESET_OVERWRITES_LAA /* errata */
+ | FLAG_TARC_SPEED_MODE_BIT /* errata */
+ | FLAG_APME_CHECK_PORT_B,
+ .pba = 38,
+ .max_hw_frame_size = DEFAULT_JUMBO,
+ .init_ops = e1000e_init_function_pointers_82571,
+ .get_variants = e1000e_get_variants_82571,
+};
+
+static struct e1000_info e1000_82572_info = {
+ .mac = e1000_82572,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_TARC_SPEED_MODE_BIT, /* errata */
+ .pba = 38,
+ .max_hw_frame_size = DEFAULT_JUMBO,
+ .init_ops = e1000e_init_function_pointers_82571,
+ .get_variants = e1000e_get_variants_82571,
+};
+
+static struct e1000_info e1000_82573_info = {
+ .mac = e1000_82573,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_SMART_POWER_DOWN
+ | FLAG_HAS_AMT
+ | FLAG_HAS_ERT
+ | FLAG_HAS_SWSM_ON_LOAD,
+ .pba = 20,
+ .max_hw_frame_size = ETH_FRAME_LEN + ETH_FCS_LEN,
+ .init_ops = e1000e_init_function_pointers_82571,
+ .get_variants = e1000e_get_variants_82571,
+};
+
+static struct e1000_info e1000_82574_info = {
+ .mac = e1000_82574,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+#ifdef CONFIG_E1000E_MSIX
+ | FLAG_HAS_MSIX
+#endif
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_SMART_POWER_DOWN
+ | FLAG_HAS_AMT
+ | FLAG_HAS_CTRLEXT_ON_LOAD,
+ .pba = 20,
+ .max_hw_frame_size = DEFAULT_JUMBO,
+ .init_ops = e1000e_init_function_pointers_82571,
+ .get_variants = e1000e_get_variants_82571,
+};
+
+static struct e1000_info e1000_82583_info = {
+ .mac = e1000_82583,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_SMART_POWER_DOWN
+ | FLAG_HAS_AMT
+ | FLAG_HAS_CTRLEXT_ON_LOAD,
+ .pba = 20,
+ .max_hw_frame_size = ETH_FRAME_LEN + ETH_FCS_LEN,
+ .init_ops = e1000e_init_function_pointers_82571,
+ .get_variants = e1000e_get_variants_82571,
+};
+
+static struct e1000_info e1000_es2_info = {
+ .mac = e1000_80003es2lan,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_RX_NEEDS_RESTART /* errata */
+ | FLAG_TARC_SET_BIT_ZERO /* errata */
+ | FLAG_APME_CHECK_PORT_B
+ | FLAG_DISABLE_FC_PAUSE_TIME /* errata */
+ | FLAG_TIPG_MEDIUM_FOR_80003ESLAN,
+ .pba = 38,
+ .max_hw_frame_size = DEFAULT_JUMBO,
+ .init_ops = e1000e_init_function_pointers_80003es2lan,
+ .get_variants = NULL,
+};
+
+static s32 e1000e_get_variants_ich8lan(struct e1000_adapter *adapter)
+{
+ if (adapter->hw.phy.type == e1000_phy_ife) {
+ adapter->flags &= ~FLAG_HAS_JUMBO_FRAMES;
+ adapter->max_hw_frame_size = ETH_FRAME_LEN + ETH_FCS_LEN;
+ }
+
+ if ((adapter->hw.mac.type == e1000_ich8lan) &&
+ (adapter->hw.phy.type == e1000_phy_igp_3))
+ adapter->flags |= FLAG_LSC_GIG_SPEED_DROP;
+
+ return 0;
+}
+
+static struct e1000_info e1000_ich8_info = {
+ .mac = e1000_ich8lan,
+ .flags = FLAG_HAS_WOL
+ | FLAG_IS_ICH
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_HAS_AMT
+ | FLAG_HAS_FLASH
+ | FLAG_APME_IN_WUC,
+ .pba = 8,
+ .max_hw_frame_size = ETH_FRAME_LEN + ETH_FCS_LEN,
+ .init_ops = e1000e_init_function_pointers_ich8lan,
+ .get_variants = e1000e_get_variants_ich8lan,
+};
+
+static struct e1000_info e1000_ich9_info = {
+ .mac = e1000_ich9lan,
+ .flags = FLAG_HAS_JUMBO_FRAMES
+ | FLAG_IS_ICH
+ | FLAG_HAS_WOL
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_HAS_AMT
+ | FLAG_HAS_ERT
+ | FLAG_HAS_FLASH
+ | FLAG_APME_IN_WUC,
+ .pba = 10,
+ .max_hw_frame_size = DEFAULT_JUMBO,
+ .init_ops = e1000e_init_function_pointers_ich8lan,
+ .get_variants = e1000e_get_variants_ich8lan,
+};
+
+static struct e1000_info e1000_ich10_info = {
+ .mac = e1000_ich10lan,
+ .flags = FLAG_HAS_JUMBO_FRAMES
+ | FLAG_IS_ICH
+ | FLAG_HAS_WOL
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_HAS_AMT
+ | FLAG_HAS_ERT
+ | FLAG_HAS_FLASH
+ | FLAG_APME_IN_WUC,
+ .pba = 10,
+ .max_hw_frame_size = DEFAULT_JUMBO,
+ .init_ops = e1000e_init_function_pointers_ich8lan,
+ .get_variants = e1000e_get_variants_ich8lan,
+};
+
+static struct e1000_info e1000_pch_info = {
+ .mac = e1000_pchlan,
+ .flags = FLAG_IS_ICH
+ | FLAG_HAS_WOL
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_HAS_AMT
+ | FLAG_HAS_FLASH
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_DISABLE_FC_PAUSE_TIME /* errata */
+ | FLAG_APME_IN_WUC,
+ .pba = 26,
+ .max_hw_frame_size = 4096,
+ .init_ops = e1000e_init_function_pointers_ich8lan,
+ .get_variants = e1000e_get_variants_ich8lan,
+};
+
+static const struct e1000_info *e1000_info_tbl[] = {
+ [board_82571] = &e1000_82571_info,
+ [board_82572] = &e1000_82572_info,
+ [board_82573] = &e1000_82573_info,
+ [board_82574] = &e1000_82574_info,
+ [board_82583] = &e1000_82583_info,
+ [board_80003es2lan] = &e1000_es2_info,
+ [board_ich8lan] = &e1000_ich8_info,
+ [board_ich9lan] = &e1000_ich9_info,
+ [board_ich10lan] = &e1000_ich10_info,
+ [board_pchlan] = &e1000_pch_info,
+};
+
+/* Low-level support routines */
+
+s32 e1000e_read_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value)
+{
+ u16 cap_offset;
+
+ cap_offset = pci_find_capability(hw->adapter->pdev, PCI_CAP_ID_EXP);
+ if (!cap_offset)
+ return -E1000_ERR_CONFIG;
+
+ pci_read_config_word(hw->adapter->pdev, cap_offset + reg, value);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_irq_disable - Mask off interrupt generation on the NIC
+ **/
+static void e1000e_irq_disable(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ ew32(IMC, ~0);
+ e1e_flush();
+}
+
+/**
+ * e1000e_irq_enable - Enable default interrupt generation settings
+ **/
+static void e1000e_irq_enable(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ ew32(IMS, IMS_ENABLE_MASK);
+ e1e_flush();
+}
+
+/**
+ * e1000_get_hw_control - get control of the h/w from f/w
+ * @adapter: address of board private structure
+ *
+ * e1000_get_hw_control sets {CTRL_EXT|SWSM}:DRV_LOAD bit.
+ * For ASF and Pass Through versions of f/w this means that
+ * the driver is loaded. For AMT version (only with 82573)
+ * of the f/w this means that the network i/f is open.
+ **/
+static void e1000e_get_hw_control(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl_ext;
+ u32 swsm;
+
+ /* Let firmware know the driver has taken over */
+ if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) {
+ swsm = er32(SWSM);
+ ew32(SWSM, swsm | E1000_SWSM_DRV_LOAD);
+ } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) {
+ ctrl_ext = er32(CTRL_EXT);
+ ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_DRV_LOAD);
+ }
+}
+
+/**
+ * e1000e_power_up_phy - restore link in case the phy was powered down
+ * @adapter: address of board private structure
+ *
+ * The phy may be powered down to save power and turn off link when the
+ * driver is unloaded and wake on lan is not enabled (among others)
+ * *** this routine MUST be followed by a call to e1000e_reset ***
+ **/
+void e1000e_power_up_phy(struct e1000_adapter *adapter)
+{
+ if (adapter->hw.phy.ops.power_up)
+ adapter->hw.phy.ops.power_up(&adapter->hw);
+
+ adapter->hw.mac.ops.setup_link(&adapter->hw);
+}
+
+/**
+ * e1000_power_down_phy - Power down the PHY
+ *
+ * Power down the PHY so no link is implied when interface is down.
+ * The PHY cannot be powered down if management or WoL is active.
+ */
+void e1000e_power_down_phy(struct e1000_adapter *adapter)
+{
+ /* WoL is enabled */
+ if (adapter->wol)
+ return;
+
+ if (adapter->hw.phy.ops.power_down)
+ adapter->hw.phy.ops.power_down(&adapter->hw);
+}
+
+/**
+ * e1000e_reset - bring the hardware into a known good state
+ *
+ * This function boots the hardware and enables some settings that
+ * require a configuration cycle of the hardware - those cannot be
+ * set/changed during runtime. After reset the device needs to be
+ * properly configured for Rx, Tx etc.
+ */
+void e1000e_reset(struct e1000_adapter *adapter)
+{
+ struct e1000_mac_info *mac = &adapter->hw.mac;
+ struct e1000_fc_info *fc = &adapter->hw.fc;
+ u32 pba = adapter->pba;
+ struct e1000_hw *hw = &adapter->hw;
+
+ /* Reset Packet Buffer Allocation to default */
+ ew32(PBA, pba);
+
+ hw->fc.requested_mode = e1000_fc_none;
+ fc->current_mode = fc->requested_mode;
+
+ /* Allow time for pending master requests to run */
+ mac->ops.reset_hw(hw);
+
+ /*
+ * For parts with AMT enabled, let the firmware know
+ * that the network interface is in control
+ */
+ if (adapter->flags & FLAG_HAS_AMT)
+ e1000e_get_hw_control(adapter);
+
+ ew32(WUC, 0);
+ if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP)
+ e1e_wphy(&adapter->hw, BM_WUC, 0);
+
+ if (mac->ops.init_hw(hw))
+ DBG("Hardware Error\n");
+
+ /* additional part of the flow-control workaround above */
+ if (hw->mac.type == e1000_pchlan)
+ ew32(FCRTV_PCH, 0x1000);
+
+ e1000e_reset_adaptive(hw);
+
+ e1000e_get_phy_info(hw);
+
+ if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN) &&
+ !(adapter->flags & FLAG_SMART_POWER_DOWN)) {
+ u16 phy_data = 0;
+ /*
+ * speed up time to link by disabling smart power down, ignore
+ * the return value of this function because there is nothing
+ * different we would do if it failed
+ */
+ e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
+ phy_data &= ~IGP02E1000_PM_SPD;
+ e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
+ }
+}
+
+static int e1000e_sw_init(struct e1000_adapter *adapter)
+{
+ s32 rc;
+
+ /* Set various function pointers */
+ adapter->ei->init_ops(&adapter->hw);
+
+ rc = adapter->hw.mac.ops.init_params(&adapter->hw);
+ if (rc)
+ return rc;
+
+ rc = adapter->hw.nvm.ops.init_params(&adapter->hw);
+ if (rc)
+ return rc;
+
+ rc = adapter->hw.phy.ops.init_params(&adapter->hw);
+ if (rc)
+ return rc;
+
+ /* Explicitly disable IRQ since the NIC can be in any state. */
+ e1000e_irq_disable(adapter);
+
+ return E1000_SUCCESS;
+}
+
+/* TX support routines */
+
+/**
+ * e1000_setup_tx_resources - allocate Tx resources (Descriptors)
+ *
+ * @v adapter e1000 private structure
+ *
+ * @ret rc Returns 0 on success, negative on failure
+ **/
+static int e1000e_setup_tx_resources ( struct e1000_adapter *adapter )
+{
+ DBGP ( "e1000_setup_tx_resources\n" );
+
+ /* Allocate transmit descriptor ring memory.
+ It must not cross a 64K boundary because of hardware errata #23
+ so we use malloc_dma() requesting a 128 byte block that is
+ 128 byte aligned. This should guarantee that the memory
+ allocated will not cross a 64K boundary, because 128 is an
+ even multiple of 65536 ( 65536 / 128 == 512 ), so all possible
+ allocations of 128 bytes on a 128 byte boundary will not
+ cross 64K bytes.
+ */
+
+ adapter->tx_base =
+ malloc_dma ( adapter->tx_ring_size, adapter->tx_ring_size );
+
+ if ( ! adapter->tx_base ) {
+ return -ENOMEM;
+ }
+
+ memset ( adapter->tx_base, 0, adapter->tx_ring_size );
+
+ DBG ( "adapter->tx_base = %#08lx\n", virt_to_bus ( adapter->tx_base ) );
+
+ return 0;
+}
+
+/**
+ * e1000_process_tx_packets - process transmitted packets
+ *
+ * @v netdev network interface device structure
+ **/
+static void e1000e_process_tx_packets ( struct net_device *netdev )
+{
+ struct e1000_adapter *adapter = netdev_priv ( netdev );
+ uint32_t i;
+ uint32_t tx_status;
+ struct e1000_tx_desc *tx_curr_desc;
+
+ /* Check status of transmitted packets
+ */
+ DBG ( "process_tx_packets: tx_head = %d, tx_tail = %d\n", adapter->tx_head,
+ adapter->tx_tail );
+
+ while ( ( i = adapter->tx_head ) != adapter->tx_tail ) {
+
+ tx_curr_desc = ( void * ) ( adapter->tx_base ) +
+ ( i * sizeof ( *adapter->tx_base ) );
+
+ tx_status = tx_curr_desc->upper.data;
+
+ DBG ( " tx_curr_desc = %#08lx\n", virt_to_bus ( tx_curr_desc ) );
+ DBG ( " tx_status = %#08x\n", tx_status );
+
+ /* if the packet at tx_head is not owned by hardware it is for us */
+ if ( ! ( tx_status & E1000_TXD_STAT_DD ) )
+ break;
+
+ DBG ( "Sent packet. tx_head: %d tx_tail: %d tx_status: %#08x\n",
+ adapter->tx_head, adapter->tx_tail, tx_status );
+
+ if ( tx_status & ( E1000_TXD_STAT_EC | E1000_TXD_STAT_LC |
+ E1000_TXD_STAT_TU ) ) {
+ netdev_tx_complete_err ( netdev, adapter->tx_iobuf[i], -EINVAL );
+ DBG ( "Error transmitting packet, tx_status: %#08x\n",
+ tx_status );
+ } else {
+ netdev_tx_complete ( netdev, adapter->tx_iobuf[i] );
+ DBG ( "Success transmitting packet, tx_status: %#08x\n",
+ tx_status );
+ }
+
+ /* Decrement count of used descriptors, clear this descriptor
+ */
+ adapter->tx_fill_ctr--;
+ memset ( tx_curr_desc, 0, sizeof ( *tx_curr_desc ) );
+
+ adapter->tx_head = ( adapter->tx_head + 1 ) % NUM_TX_DESC;
+ }
+}
+
+static void e1000e_free_tx_resources ( struct e1000_adapter *adapter )
+{
+ DBGP ( "e1000_free_tx_resources\n" );
+
+ free_dma ( adapter->tx_base, adapter->tx_ring_size );
+}
+
+/**
+ * e1000_configure_tx - Configure 8254x Transmit Unit after Reset
+ * @adapter: board private structure
+ *
+ * Configure the Tx unit of the MAC after a reset.
+ **/
+static void e1000e_configure_tx ( struct e1000_adapter *adapter )
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 tctl, tipg, tarc;
+ u32 ipgr1, ipgr2;
+
+ DBGP ( "e1000_configure_tx\n" );
+
+ /* disable transmits while setting up the descriptors */
+ tctl = E1000_READ_REG ( hw, E1000_TCTL );
+ E1000_WRITE_REG ( hw, E1000_TCTL, tctl & ~E1000_TCTL_EN );
+ e1e_flush();
+ mdelay(10);
+
+ E1000_WRITE_REG ( hw, E1000_TDBAH(0), 0 );
+ E1000_WRITE_REG ( hw, E1000_TDBAL(0), virt_to_bus ( adapter->tx_base ) );
+ E1000_WRITE_REG ( hw, E1000_TDLEN(0), adapter->tx_ring_size );
+
+ DBG ( "E1000_TDBAL(0): %#08x\n", E1000_READ_REG ( hw, E1000_TDBAL(0) ) );
+ DBG ( "E1000_TDLEN(0): %d\n", E1000_READ_REG ( hw, E1000_TDLEN(0) ) );
+
+ /* Setup the HW Tx Head and Tail descriptor pointers */
+ E1000_WRITE_REG ( hw, E1000_TDH(0), 0 );
+ E1000_WRITE_REG ( hw, E1000_TDT(0), 0 );
+
+ adapter->tx_head = 0;
+ adapter->tx_tail = 0;
+ adapter->tx_fill_ctr = 0;
+
+ /* Set the default values for the Tx Inter Packet Gap timer */
+ tipg = DEFAULT_82543_TIPG_IPGT_COPPER; /* 8 */
+ ipgr1 = DEFAULT_82543_TIPG_IPGR1; /* 8 */
+ ipgr2 = DEFAULT_82543_TIPG_IPGR2; /* 6 */
+
+ if (adapter->flags & FLAG_TIPG_MEDIUM_FOR_80003ESLAN)
+ ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2; /* 7 */
+
+ tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT;
+ tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT;
+ ew32(TIPG, tipg);
+
+ /* Program the Transmit Control Register */
+ tctl = er32(TCTL);
+ tctl &= ~E1000_TCTL_CT;
+ tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC |
+ (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
+
+ if (adapter->flags & FLAG_TARC_SPEED_MODE_BIT) {
+ tarc = er32(TARC(0));
+ /*
+ * set the speed mode bit, we'll clear it if we're not at
+ * gigabit link later
+ */
+#define SPEED_MODE_BIT (1 << 21)
+ tarc |= SPEED_MODE_BIT;
+ ew32(TARC(0), tarc);
+ }
+
+ /* errata: program both queues to unweighted RR */
+ if (adapter->flags & FLAG_TARC_SET_BIT_ZERO) {
+ tarc = er32(TARC(0));
+ tarc |= 1;
+ ew32(TARC(0), tarc);
+ tarc = er32(TARC(1));
+ tarc |= 1;
+ ew32(TARC(1), tarc);
+ }
+
+ /* Setup Transmit Descriptor Settings for eop descriptor */
+ adapter->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS;
+
+ /* enable Report Status bit */
+ adapter->txd_cmd |= E1000_TXD_CMD_RS;
+
+ /*
+ * enable transmits in the hardware, need to do this
+ * after setting TARC(0)
+ */
+ tctl |= E1000_TCTL_EN;
+ ew32(TCTL, tctl);
+ e1e_flush();
+
+ e1000e_config_collision_dist(hw);
+}
+
+/* RX support routines */
+
+static void e1000e_free_rx_resources ( struct e1000_adapter *adapter )
+{
+ int i;
+
+ DBGP ( "e1000_free_rx_resources\n" );
+
+ free_dma ( adapter->rx_base, adapter->rx_ring_size );
+
+ for ( i = 0; i < NUM_RX_DESC; i++ ) {
+ free_iob ( adapter->rx_iobuf[i] );
+ }
+}
+
+/**
+ * e1000_refill_rx_ring - allocate Rx io_buffers
+ *
+ * @v adapter e1000 private structure
+ *
+ * @ret rc Returns 0 on success, negative on failure
+ **/
+static int e1000e_refill_rx_ring ( struct e1000_adapter *adapter )
+{
+ int i, rx_curr;
+ int rc = 0;
+ struct e1000_rx_desc *rx_curr_desc;
+ struct e1000_hw *hw = &adapter->hw;
+ struct io_buffer *iob;
+
+ DBGP ("e1000_refill_rx_ring\n");
+
+ for ( i = 0; i < NUM_RX_DESC; i++ ) {
+ rx_curr = ( ( adapter->rx_curr + i ) % NUM_RX_DESC );
+ rx_curr_desc = adapter->rx_base + rx_curr;
+
+ if ( rx_curr_desc->status & E1000_RXD_STAT_DD )
+ continue;
+
+ if ( adapter->rx_iobuf[rx_curr] != NULL )
+ continue;
+
+ DBG2 ( "Refilling rx desc %d\n", rx_curr );
+
+ iob = alloc_iob ( MAXIMUM_ETHERNET_VLAN_SIZE );
+ adapter->rx_iobuf[rx_curr] = iob;
+
+ if ( ! iob ) {
+ DBG ( "alloc_iob failed\n" );
+ rc = -ENOMEM;
+ break;
+ } else {
+ rx_curr_desc->buffer_addr = virt_to_bus ( iob->data );
+
+ E1000_WRITE_REG ( hw, E1000_RDT(0), rx_curr );
+ }
+ }
+ return rc;
+}
+
+/**
+ * e1000_setup_rx_resources - allocate Rx resources (Descriptors)
+ *
+ * @v adapter e1000 private structure
+ *
+ * @ret rc Returns 0 on success, negative on failure
+ **/
+static int e1000e_setup_rx_resources ( struct e1000_adapter *adapter )
+{
+ int i, rc = 0;
+
+ DBGP ( "e1000_setup_rx_resources\n" );
+
+ /* Allocate receive descriptor ring memory.
+ It must not cross a 64K boundary because of hardware errata
+ */
+
+ adapter->rx_base =
+ malloc_dma ( adapter->rx_ring_size, adapter->rx_ring_size );
+
+ if ( ! adapter->rx_base ) {
+ return -ENOMEM;
+ }
+ memset ( adapter->rx_base, 0, adapter->rx_ring_size );
+
+ for ( i = 0; i < NUM_RX_DESC; i++ ) {
+ /* let e1000_refill_rx_ring() io_buffer allocations */
+ adapter->rx_iobuf[i] = NULL;
+ }
+
+ /* allocate io_buffers */
+ rc = e1000e_refill_rx_ring ( adapter );
+ if ( rc < 0 )
+ e1000e_free_rx_resources ( adapter );
+
+ return rc;
+}
+
+/**
+ * e1000_configure_rx - Configure 8254x Receive Unit after Reset
+ * @adapter: board private structure
+ *
+ * Configure the Rx unit of the MAC after a reset.
+ **/
+static void e1000e_configure_rx ( struct e1000_adapter *adapter )
+{
+ struct e1000_hw *hw = &adapter->hw;
+ uint32_t rctl;
+
+ DBGP ( "e1000_configure_rx\n" );
+
+ /* disable receives while setting up the descriptors */
+ rctl = E1000_READ_REG ( hw, E1000_RCTL );
+ E1000_WRITE_REG ( hw, E1000_RCTL, rctl & ~E1000_RCTL_EN );
+ e1e_flush();
+ mdelay(10);
+
+ adapter->rx_curr = 0;
+
+ /* Setup the HW Rx Head and Tail Descriptor Pointers and
+ * the Base and Length of the Rx Descriptor Ring */
+
+ E1000_WRITE_REG ( hw, E1000_RDBAL(0), virt_to_bus ( adapter->rx_base ) );
+ E1000_WRITE_REG ( hw, E1000_RDBAH(0), 0 );
+ E1000_WRITE_REG ( hw, E1000_RDLEN(0), adapter->rx_ring_size );
+
+ E1000_WRITE_REG ( hw, E1000_RDH(0), 0 );
+ E1000_WRITE_REG ( hw, E1000_RDT(0), NUM_RX_DESC - 1 );
+
+ /* Enable Receives */
+ rctl |= E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_SZ_2048 |
+ E1000_RCTL_MPE;
+ E1000_WRITE_REG ( hw, E1000_RCTL, rctl );
+ e1e_flush();
+
+ DBG ( "E1000_RDBAL(0): %#08x\n", E1000_READ_REG ( hw, E1000_RDBAL(0) ) );
+ DBG ( "E1000_RDLEN(0): %d\n", E1000_READ_REG ( hw, E1000_RDLEN(0) ) );
+ DBG ( "E1000_RCTL: %#08x\n", E1000_READ_REG ( hw, E1000_RCTL ) );
+}
+
+/**
+ * e1000_process_rx_packets - process received packets
+ *
+ * @v netdev network interface device structure
+ **/
+static void e1000e_process_rx_packets ( struct net_device *netdev )
+{
+ struct e1000_adapter *adapter = netdev_priv ( netdev );
+ uint32_t i;
+ uint32_t rx_status;
+ uint32_t rx_len;
+ uint32_t rx_err;
+ struct e1000_rx_desc *rx_curr_desc;
+
+ /* Process received packets
+ */
+ while ( 1 ) {
+
+ i = adapter->rx_curr;
+
+ rx_curr_desc = ( void * ) ( adapter->rx_base ) +
+ ( i * sizeof ( *adapter->rx_base ) );
+ rx_status = rx_curr_desc->status;
+
+ DBG2 ( "Before DD Check RX_status: %#08x\n", rx_status );
+
+ if ( ! ( rx_status & E1000_RXD_STAT_DD ) )
+ break;
+
+ if ( adapter->rx_iobuf[i] == NULL )
+ break;
+
+ DBG ( "E1000_RCTL = %#08x\n", E1000_READ_REG ( &adapter->hw, E1000_RCTL ) );
+
+ rx_len = rx_curr_desc->length;
+
+ DBG ( "Received packet, rx_curr: %d rx_status: %#08x rx_len: %d\n",
+ i, rx_status, rx_len );
+
+ rx_err = rx_curr_desc->errors;
+
+ iob_put ( adapter->rx_iobuf[i], rx_len );
+
+ if ( rx_err & E1000_RXD_ERR_FRAME_ERR_MASK ) {
+
+ netdev_rx_err ( netdev, adapter->rx_iobuf[i], -EINVAL );
+ DBG ( "e1000_poll: Corrupted packet received!"
+ " rx_err: %#08x\n", rx_err );
+ } else {
+ /* Add this packet to the receive queue. */
+ netdev_rx ( netdev, adapter->rx_iobuf[i] );
+ }
+ adapter->rx_iobuf[i] = NULL;
+
+ memset ( rx_curr_desc, 0, sizeof ( *rx_curr_desc ) );
+
+ adapter->rx_curr = ( adapter->rx_curr + 1 ) % NUM_RX_DESC;
+ }
+}
+
+/** Functions that implement the gPXE driver API **/
+
+/**
+ * e1000_close - Disables a network interface
+ *
+ * @v netdev network interface device structure
+ *
+ **/
+static void e1000e_close ( struct net_device *netdev )
+{
+ struct e1000_adapter *adapter = netdev_priv ( netdev );
+ struct e1000_hw *hw = &adapter->hw;
+ uint32_t rctl;
+ uint32_t icr;
+
+ DBGP ( "e1000_close\n" );
+
+ /* Acknowledge interrupts */
+ icr = E1000_READ_REG ( hw, E1000_ICR );
+
+ e1000e_irq_disable ( adapter );
+
+ /* disable receives */
+ rctl = E1000_READ_REG ( hw, E1000_RCTL );
+ E1000_WRITE_REG ( hw, E1000_RCTL, rctl & ~E1000_RCTL_EN );
+ e1e_flush();
+
+ e1000e_reset ( adapter );
+
+ e1000e_free_tx_resources ( adapter );
+ e1000e_free_rx_resources ( adapter );
+}
+
+/**
+ * e1000_transmit - Transmit a packet
+ *
+ * @v netdev Network device
+ * @v iobuf I/O buffer
+ *
+ * @ret rc Returns 0 on success, negative on failure
+ */
+static int e1000e_transmit ( struct net_device *netdev, struct io_buffer *iobuf )
+{
+ struct e1000_adapter *adapter = netdev_priv( netdev );
+ struct e1000_hw *hw = &adapter->hw;
+ uint32_t tx_curr = adapter->tx_tail;
+ struct e1000_tx_desc *tx_curr_desc;
+
+ DBGP ("e1000_transmit\n");
+
+ if ( adapter->tx_fill_ctr == NUM_TX_DESC ) {
+ DBG ("TX overflow\n");
+ return -ENOBUFS;
+ }
+
+ /* Save pointer to iobuf we have been given to transmit,
+ netdev_tx_complete() will need it later
+ */
+ adapter->tx_iobuf[tx_curr] = iobuf;
+
+ tx_curr_desc = ( void * ) ( adapter->tx_base ) +
+ ( tx_curr * sizeof ( *adapter->tx_base ) );
+
+ DBG ( "tx_curr_desc = %#08lx\n", virt_to_bus ( tx_curr_desc ) );
+ DBG ( "tx_curr_desc + 16 = %#08lx\n", virt_to_bus ( tx_curr_desc ) + 16 );
+ DBG ( "iobuf->data = %#08lx\n", virt_to_bus ( iobuf->data ) );
+
+ /* Add the packet to TX ring
+ */
+ tx_curr_desc->buffer_addr = virt_to_bus ( iobuf->data );
+ tx_curr_desc->upper.data = 0;
+ tx_curr_desc->lower.data = adapter->txd_cmd | iob_len ( iobuf );
+
+ DBG ( "TX fill: %d tx_curr: %d addr: %#08lx len: %zd\n", adapter->tx_fill_ctr,
+ tx_curr, virt_to_bus ( iobuf->data ), iob_len ( iobuf ) );
+
+ /* Point to next free descriptor */
+ adapter->tx_tail = ( adapter->tx_tail + 1 ) % NUM_TX_DESC;
+ adapter->tx_fill_ctr++;
+
+ /* Write new tail to NIC, making packet available for transmit
+ */
+ E1000_WRITE_REG ( hw, E1000_TDT(0), adapter->tx_tail );
+ e1e_flush();
+
+ return 0;
+}
+
+/**
+ * e1000_poll - Poll for received packets
+ *
+ * @v netdev Network device
+ */
+static void e1000e_poll ( struct net_device *netdev )
+{
+ struct e1000_adapter *adapter = netdev_priv( netdev );
+ struct e1000_hw *hw = &adapter->hw;
+
+ uint32_t icr;
+
+ DBGP ( "e1000_poll\n" );
+
+ /* Acknowledge interrupts */
+ icr = E1000_READ_REG ( hw, E1000_ICR );
+ if ( ! icr )
+ return;
+
+ DBG ( "e1000_poll: intr_status = %#08x\n", icr );
+
+ e1000e_process_tx_packets ( netdev );
+
+ e1000e_process_rx_packets ( netdev );
+
+ e1000e_refill_rx_ring(adapter);
+}
+
+/**
+ * e1000_irq - enable or Disable interrupts
+ *
+ * @v adapter e1000 adapter
+ * @v action requested interrupt action
+ **/
+static void e1000e_irq ( struct net_device *netdev, int enable )
+{
+ struct e1000_adapter *adapter = netdev_priv ( netdev );
+
+ DBGP ( "e1000_irq\n" );
+
+ if ( enable ) {
+ e1000e_irq_enable ( adapter );
+ } else {
+ e1000e_irq_disable ( adapter );
+ }
+}
+
+static struct net_device_operations e1000e_operations;
+
+/**
+ * e1000_probe - Initial configuration of e1000 NIC
+ *
+ * @v pci PCI device
+ * @v id PCI IDs
+ *
+ * @ret rc Return status code
+ **/
+int e1000e_probe ( struct pci_device *pdev,
+ const struct pci_device_id *ent)
+{
+ int i, err;
+ struct net_device *netdev;
+ struct e1000_adapter *adapter;
+ unsigned long mmio_start, mmio_len;
+ unsigned long flash_start, flash_len;
+ struct e1000_hw *hw;
+ const struct e1000_info *ei = e1000_info_tbl[ent->driver_data];
+
+ DBGP ( "e1000_probe\n" );
+
+ err = -ENOMEM;
+
+ /* Allocate net device ( also allocates memory for netdev->priv
+ and makes netdev-priv point to it ) */
+ netdev = alloc_etherdev ( sizeof ( struct e1000_adapter ) );
+ if ( ! netdev ) {
+ DBG ( "err_alloc_etherdev\n" );
+ goto err_alloc_etherdev;
+ }
+
+ /* Associate e1000-specific network operations operations with
+ * generic network device layer */
+ netdev_init ( netdev, &e1000e_operations );
+
+ /* Associate this network device with given PCI device */
+ pci_set_drvdata ( pdev, netdev );
+ netdev->dev = &pdev->dev;
+
+ /* Initialize driver private storage */
+ adapter = netdev_priv ( netdev );
+ memset ( adapter, 0, ( sizeof ( *adapter ) ) );
+
+ adapter->pdev = pdev;
+
+ adapter->ioaddr = pdev->ioaddr;
+ adapter->hw.io_base = pdev->ioaddr;
+
+ hw = &adapter->hw;
+ hw->device_id = pdev->device;
+
+ adapter->irqno = pdev->irq;
+ adapter->netdev = netdev;
+ adapter->hw.back = adapter;
+
+ adapter->ei = ei;
+ adapter->pba = ei->pba;
+ adapter->flags = ei->flags;
+ adapter->flags2 = ei->flags2;
+
+ adapter->hw.adapter = adapter;
+ adapter->hw.mac.type = ei->mac;
+ adapter->max_hw_frame_size = ETH_FRAME_LEN + ETH_FCS_LEN;
+
+ adapter->tx_ring_size = sizeof ( *adapter->tx_base ) * NUM_TX_DESC;
+ adapter->rx_ring_size = sizeof ( *adapter->rx_base ) * NUM_RX_DESC;
+
+ /* Fix up PCI device */
+ adjust_pci_device ( pdev );
+
+ err = -EIO;
+
+ mmio_start = pci_bar_start ( pdev, PCI_BASE_ADDRESS_0 );
+ mmio_len = pci_bar_size ( pdev, PCI_BASE_ADDRESS_0 );
+
+ DBG ( "mmio_start: %#08lx\n", mmio_start );
+ DBG ( "mmio_len: %#08lx\n", mmio_len );
+
+ adapter->hw.hw_addr = ioremap ( mmio_start, mmio_len );
+ DBG ( "adapter->hw.hw_addr: %p\n", adapter->hw.hw_addr );
+
+ if ( ! adapter->hw.hw_addr ) {
+ DBG ( "err_ioremap\n" );
+ goto err_ioremap;
+ }
+
+ /* Flash BAR mapping depends on mac_type */
+ if ( ( adapter->flags & FLAG_HAS_FLASH) && ( pdev->ioaddr ) ) {
+ flash_start = pci_bar_start ( pdev, PCI_BASE_ADDRESS_1 );
+ flash_len = pci_bar_size ( pdev, PCI_BASE_ADDRESS_1 );
+ adapter->hw.flash_address = ioremap ( flash_start, flash_len );
+ if ( ! adapter->hw.flash_address ) {
+ DBG ( "err_flashmap\n" );
+ goto err_flashmap;
+ }
+ }
+
+ /* setup adapter struct */
+ err = e1000e_sw_init ( adapter );
+ if (err) {
+ DBG ( "err_sw_init\n" );
+ goto err_sw_init;
+ }
+
+ if (ei->get_variants) {
+ err = ei->get_variants(adapter);
+ if (err) {
+ DBG ( "err_hw_initr\n" );
+ goto err_hw_init;
+ }
+ }
+
+ /* Copper options */
+ if (adapter->hw.phy.media_type == e1000_media_type_copper) {
+ adapter->hw.phy.mdix = AUTO_ALL_MODES;
+ adapter->hw.phy.disable_polarity_correction = 0;
+ adapter->hw.phy.ms_type = e1000_ms_hw_default;
+ }
+
+ DBG ( "adapter->hw.mac.type: %#08x\n", adapter->hw.mac.type );
+
+ /* Force auto-negotiation */
+ adapter->hw.mac.autoneg = 1;
+ adapter->fc_autoneg = 1;
+ adapter->hw.phy.autoneg_wait_to_complete = true;
+ adapter->hw.mac.adaptive_ifs = true;
+ adapter->hw.fc.requested_mode = e1000_fc_default;
+ adapter->hw.fc.current_mode = e1000_fc_default;
+
+ /*
+ * before reading the NVM, reset the controller to
+ * put the device in a known good starting state
+ */
+ adapter->hw.mac.ops.reset_hw(&adapter->hw);
+
+ /*
+ * systems with ASPM and others may see the checksum fail on the first
+ * attempt. Let's give it a few tries
+ */
+ for (i = 0;; i++) {
+ if (e1000e_validate_nvm_checksum(&adapter->hw) >= 0)
+ break;
+ if (i == 2) {
+ DBG("The NVM Checksum Is Not Valid\n");
+ err = -EIO;
+ goto err_eeprom;
+ }
+ }
+
+ /* copy the MAC address out of the EEPROM */
+ if ( e1000e_read_mac_addr ( &adapter->hw ) )
+ DBG ( "EEPROM Read Error\n" );
+
+ memcpy ( netdev->hw_addr, adapter->hw.mac.perm_addr, ETH_ALEN );
+
+ /* reset the hardware with the new settings */
+ e1000e_reset ( adapter );
+
+ /* Mark as link up; we don't yet handle link state */
+ netdev_link_up ( netdev );
+
+ if ( ( err = register_netdev ( netdev ) ) != 0) {
+ DBG ( "err_register\n" );
+ goto err_register;
+ }
+
+ for (i = 0; i < 6; i++)
+ DBG ("%02x%s", netdev->ll_addr[i], i == 5 ? "\n" : ":");
+
+ DBG ( "e1000e_probe succeeded!\n" );
+
+ /* No errors, return success */
+ return 0;
+
+/* Error return paths */
+err_register:
+err_hw_init:
+err_eeprom:
+err_flashmap:
+ if (!e1000e_check_reset_block(&adapter->hw))
+ e1000e_phy_hw_reset(&adapter->hw);
+ if (adapter->hw.flash_address)
+ iounmap(adapter->hw.flash_address);
+err_sw_init:
+ iounmap ( adapter->hw.hw_addr );
+err_ioremap:
+ netdev_put ( netdev );
+err_alloc_etherdev:
+ return err;
+}
+
+/**
+ * e1000e_remove - Device Removal Routine
+ *
+ * @v pdev PCI device information struct
+ *
+ **/
+void e1000e_remove ( struct pci_device *pdev )
+{
+ struct net_device *netdev = pci_get_drvdata ( pdev );
+ struct e1000_adapter *adapter = netdev_priv ( netdev );
+
+ DBGP ( "e1000e_remove\n" );
+
+ if ( adapter->hw.flash_address )
+ iounmap ( adapter->hw.flash_address );
+ if ( adapter->hw.hw_addr )
+ iounmap ( adapter->hw.hw_addr );
+
+ unregister_netdev ( netdev );
+ e1000e_reset ( adapter );
+ netdev_nullify ( netdev );
+ netdev_put ( netdev );
+}
+
+/**
+ * e1000e_open - Called when a network interface is made active
+ *
+ * @v netdev network interface device structure
+ * @ret rc Return status code, 0 on success, negative value on failure
+ *
+ **/
+static int e1000e_open ( struct net_device *netdev )
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ int err;
+
+ DBGP ( "e1000e_open\n" );
+
+ /* allocate transmit descriptors */
+ err = e1000e_setup_tx_resources ( adapter );
+ if ( err ) {
+ DBG ( "Error setting up TX resources!\n" );
+ goto err_setup_tx;
+ }
+
+ /* allocate receive descriptors */
+ err = e1000e_setup_rx_resources ( adapter );
+ if ( err ) {
+ DBG ( "Error setting up RX resources!\n" );
+ goto err_setup_rx;
+ }
+
+ e1000e_configure_tx ( adapter );
+
+ e1000e_configure_rx ( adapter );
+
+ DBG ( "E1000_RXDCTL(0): %#08x\n", E1000_READ_REG ( &adapter->hw, E1000_RXDCTL(0) ) );
+
+ return 0;
+
+err_setup_rx:
+ DBG ( "err_setup_rx\n" );
+ e1000e_free_tx_resources ( adapter );
+err_setup_tx:
+ DBG ( "err_setup_tx\n" );
+ e1000e_reset ( adapter );
+
+ return err;
+}
+
+/** e1000e net device operations */
+static struct net_device_operations e1000e_operations = {
+ .open = e1000e_open,
+ .close = e1000e_close,
+ .transmit = e1000e_transmit,
+ .poll = e1000e_poll,
+ .irq = e1000e_irq,
+};
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#if 0
+
+#include "e1000e.h"
+
+static u8 e1000e_calculate_checksum(u8 *buffer, u32 length);
+
+/**
+ * e1000e_calculate_checksum - Calculate checksum for buffer
+ * @buffer: pointer to EEPROM
+ * @length: size of EEPROM to calculate a checksum for
+ *
+ * Calculates the checksum for some buffer on a specified length. The
+ * checksum calculated is returned.
+ **/
+static u8 e1000e_calculate_checksum(u8 *buffer, u32 length)
+{
+ u32 i;
+ u8 sum = 0;
+
+ if (!buffer)
+ return 0;
+ for (i = 0; i < length; i++)
+ sum += buffer[i];
+
+ return (u8) (0 - sum);
+}
+
+/**
+ * e1000e_mng_enable_host_if_generic - Checks host interface is enabled
+ * @hw: pointer to the HW structure
+ *
+ * Returns E1000_success upon success, else E1000_ERR_HOST_INTERFACE_COMMAND
+ *
+ * This function checks whether the HOST IF is enabled for command operation
+ * and also checks whether the previous command is completed. It busy waits
+ * in case of previous command is not completed.
+ **/
+s32 e1000e_mng_enable_host_if_generic(struct e1000_hw *hw)
+{
+ u32 hicr;
+ s32 ret_val = E1000_SUCCESS;
+ u8 i;
+
+ /* Check that the host interface is enabled. */
+ hicr = er32(HICR);
+ if ((hicr & E1000_HICR_EN) == 0) {
+ e_dbg("E1000_HOST_EN bit disabled.\n");
+ ret_val = -E1000_ERR_HOST_INTERFACE_COMMAND;
+ goto out;
+ }
+ /* check the previous command is completed */
+ for (i = 0; i < E1000_MNG_DHCP_COMMAND_TIMEOUT; i++) {
+ hicr = er32(HICR);
+ if (!(hicr & E1000_HICR_C))
+ break;
+ mdelay(1);
+ }
+
+ if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) {
+ e_dbg("Previous command timeout failed .\n");
+ ret_val = -E1000_ERR_HOST_INTERFACE_COMMAND;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_check_mng_mode_generic - Generic check management mode
+ * @hw: pointer to the HW structure
+ *
+ * Reads the firmware semaphore register and returns true (>0) if
+ * manageability is enabled, else false (0).
+ **/
+bool e1000e_check_mng_mode_generic(struct e1000_hw *hw)
+{
+ u32 fwsm;
+
+ fwsm = er32(FWSM);
+ return (fwsm & E1000_FWSM_MODE_MASK) ==
+ (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT);
+}
+
+/**
+ * e1000e_enable_tx_pkt_filtering - Enable packet filtering on TX
+ * @hw: pointer to the HW structure
+ *
+ * Enables packet filtering on transmit packets if manageability is enabled
+ * and host interface is enabled.
+ **/
+bool e1000e_enable_tx_pkt_filtering(struct e1000_hw *hw)
+{
+ struct e1000_host_mng_dhcp_cookie *hdr = &hw->mng_cookie;
+ u32 *buffer = (u32 *)&hw->mng_cookie;
+ u32 offset;
+ s32 ret_val, hdr_csum, csum;
+ u8 i, len;
+ bool tx_filter = true;
+
+ /* No manageability, no filtering */
+ if (!hw->mac.ops.check_mng_mode(hw)) {
+ tx_filter = false;
+ goto out;
+ }
+
+ /*
+ * If we can't read from the host interface for whatever
+ * reason, disable filtering.
+ */
+ ret_val = hw->mac.ops.mng_enable_host_if(hw);
+ if (ret_val != E1000_SUCCESS) {
+ tx_filter = false;
+ goto out;
+ }
+
+ /* Read in the header. Length and offset are in dwords. */
+ len = E1000_MNG_DHCP_COOKIE_LENGTH >> 2;
+ offset = E1000_MNG_DHCP_COOKIE_OFFSET >> 2;
+ for (i = 0; i < len; i++) {
+ *(buffer + i) = E1000_READ_REG_ARRAY_DWORD(hw,
+ E1000_HOST_IF,
+ offset + i);
+ }
+ hdr_csum = hdr->checksum;
+ hdr->checksum = 0;
+ csum = e1000e_calculate_checksum((u8 *)hdr,
+ E1000_MNG_DHCP_COOKIE_LENGTH);
+ /*
+ * If either the checksums or signature don't match, then
+ * the cookie area isn't considered valid, in which case we
+ * take the safe route of assuming Tx filtering is enabled.
+ */
+ if (hdr_csum != csum)
+ goto out;
+ if (hdr->signature != E1000_IAMT_SIGNATURE)
+ goto out;
+
+ /* Cookie area is valid, make the final check for filtering. */
+ if (!(hdr->status & E1000_MNG_DHCP_COOKIE_STATUS_PARSING))
+ tx_filter = false;
+
+out:
+ hw->mac.tx_pkt_filtering = tx_filter;
+ return tx_filter;
+}
+
+/**
+ * e1000e_mng_write_dhcp_info - Writes DHCP info to host interface
+ * @hw: pointer to the HW structure
+ * @buffer: pointer to the host interface
+ * @length: size of the buffer
+ *
+ * Writes the DHCP information to the host interface.
+ **/
+s32 e1000e_mng_write_dhcp_info(struct e1000_hw *hw, u8 *buffer,
+ u16 length)
+{
+ struct e1000_host_mng_command_header hdr;
+ s32 ret_val;
+ u32 hicr;
+
+ hdr.command_id = E1000_MNG_DHCP_TX_PAYLOAD_CMD;
+ hdr.command_length = length;
+ hdr.reserved1 = 0;
+ hdr.reserved2 = 0;
+ hdr.checksum = 0;
+
+ /* Enable the host interface */
+ ret_val = hw->mac.ops.mng_enable_host_if(hw);
+ if (ret_val)
+ goto out;
+
+ /* Populate the host interface with the contents of "buffer". */
+ ret_val = hw->mac.ops.mng_host_if_write(hw, buffer, length,
+ sizeof(hdr), &(hdr.checksum));
+ if (ret_val)
+ goto out;
+
+ /* Write the manageability command header */
+ ret_val = hw->mac.ops.mng_write_cmd_header(hw, &hdr);
+ if (ret_val)
+ goto out;
+
+ /* Tell the ARC a new command is pending. */
+ hicr = er32(HICR);
+ ew32(HICR, hicr | E1000_HICR_C);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_mng_write_cmd_header_generic - Writes manageability command header
+ * @hw: pointer to the HW structure
+ * @hdr: pointer to the host interface command header
+ *
+ * Writes the command header after does the checksum calculation.
+ **/
+s32 e1000e_mng_write_cmd_header_generic(struct e1000_hw *hw,
+ struct e1000_host_mng_command_header *hdr)
+{
+ u16 i, length = sizeof(struct e1000_host_mng_command_header);
+
+ /* Write the whole command header structure with new checksum. */
+
+ hdr->checksum = e1000e_calculate_checksum((u8 *)hdr, length);
+
+ length >>= 2;
+ /* Write the relevant command block into the ram area. */
+ for (i = 0; i < length; i++) {
+ E1000_WRITE_REG_ARRAY_DWORD(hw, E1000_HOST_IF, i,
+ *((u32 *) hdr + i));
+ e1e_flush();
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_mng_host_if_write_generic - Write to the manageability host interface
+ * @hw: pointer to the HW structure
+ * @buffer: pointer to the host interface buffer
+ * @length: size of the buffer
+ * @offset: location in the buffer to write to
+ * @sum: sum of the data (not checksum)
+ *
+ * This function writes the buffer content at the offset given on the host if.
+ * It also does alignment considerations to do the writes in most efficient
+ * way. Also fills up the sum of the buffer in *buffer parameter.
+ **/
+s32 e1000e_mng_host_if_write_generic(struct e1000_hw *hw, u8 *buffer,
+ u16 length, u16 offset, u8 *sum)
+{
+ u8 *tmp;
+ u8 *bufptr = buffer;
+ u32 data = 0;
+ s32 ret_val = E1000_SUCCESS;
+ u16 remaining, i, j, prev_bytes;
+
+ /* sum = only sum of the data and it is not checksum */
+
+ if (length == 0 || offset + length > E1000_HI_MAX_MNG_DATA_LENGTH) {
+ ret_val = -E1000_ERR_PARAM;
+ goto out;
+ }
+
+ tmp = (u8 *)&data;
+ prev_bytes = offset & 0x3;
+ offset >>= 2;
+
+ if (prev_bytes) {
+ data = E1000_READ_REG_ARRAY_DWORD(hw, E1000_HOST_IF, offset);
+ for (j = prev_bytes; j < sizeof(u32); j++) {
+ *(tmp + j) = *bufptr++;
+ *sum += *(tmp + j);
+ }
+ E1000_WRITE_REG_ARRAY_DWORD(hw, E1000_HOST_IF, offset, data);
+ length -= j - prev_bytes;
+ offset++;
+ }
+
+ remaining = length & 0x3;
+ length -= remaining;
+
+ /* Calculate length in DWORDs */
+ length >>= 2;
+
+ /*
+ * The device driver writes the relevant command block into the
+ * ram area.
+ */
+ for (i = 0; i < length; i++) {
+ for (j = 0; j < sizeof(u32); j++) {
+ *(tmp + j) = *bufptr++;
+ *sum += *(tmp + j);
+ }
+
+ E1000_WRITE_REG_ARRAY_DWORD(hw, E1000_HOST_IF, offset + i,
+ data);
+ }
+ if (remaining) {
+ for (j = 0; j < sizeof(u32); j++) {
+ if (j < remaining)
+ *(tmp + j) = *bufptr++;
+ else
+ *(tmp + j) = 0;
+
+ *sum += *(tmp + j);
+ }
+ E1000_WRITE_REG_ARRAY_DWORD(hw, E1000_HOST_IF, offset + i, data);
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_enable_mng_pass_thru - Enable processing of ARP's
+ * @hw: pointer to the HW structure
+ *
+ * Verifies the hardware needs to allow ARPs to be processed by the host.
+ **/
+bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw)
+{
+ u32 manc;
+ u32 fwsm, factps;
+ bool ret_val = false;
+
+ if (!hw->mac.asf_firmware_present)
+ goto out;
+
+ manc = er32(MANC);
+
+ if (!(manc & E1000_MANC_RCV_TCO_EN) ||
+ !(manc & E1000_MANC_EN_MAC_ADDR_FILTER))
+ goto out;
+
+ if (hw->mac.arc_subsystem_valid) {
+ fwsm = er32(FWSM);
+ factps = er32(FACTPS);
+
+ if (!(factps & E1000_FACTPS_MNGCG) &&
+ ((fwsm & E1000_FWSM_MODE_MASK) ==
+ (e1000_mng_mode_pt << E1000_FWSM_MODE_SHIFT))) {
+ ret_val = true;
+ goto out;
+ }
+ } else {
+ if ((manc & E1000_MANC_SMBUS_EN) &&
+ !(manc & E1000_MANC_ASF_EN)) {
+ ret_val = true;
+ goto out;
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+#endif
+
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#ifndef _E1000E_MANAGE_H_
+#define _E1000E_MANAGE_H_
+
+bool e1000e_check_mng_mode_generic(struct e1000_hw *hw);
+bool e1000e_enable_tx_pkt_filtering(struct e1000_hw *hw);
+s32 e1000e_mng_enable_host_if_generic(struct e1000_hw *hw);
+s32 e1000e_mng_host_if_write_generic(struct e1000_hw *hw, u8 *buffer,
+ u16 length, u16 offset, u8 *sum);
+s32 e1000e_mng_write_cmd_header_generic(struct e1000_hw *hw,
+ struct e1000_host_mng_command_header *hdr);
+#if 0
+s32 e1000e_mng_write_dhcp_info(struct e1000_hw *hw,
+ u8 *buffer, u16 length);
+#endif
+bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
+
+enum e1000_mng_mode {
+ e1000_mng_mode_none = 0,
+ e1000_mng_mode_asf,
+ e1000_mng_mode_pt,
+ e1000_mng_mode_ipmi,
+ e1000_mng_mode_host_if_only
+};
+
+#define E1000_FACTPS_MNGCG 0x20000000
+
+#define E1000_FWSM_MODE_MASK 0xE
+#define E1000_FWSM_MODE_SHIFT 1
+
+#define E1000_MNG_IAMT_MODE 0x3
+#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10
+#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0
+#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10
+#define E1000_MNG_DHCP_TX_PAYLOAD_CMD 64
+#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING 0x1
+#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN 0x2
+
+#define E1000_VFTA_ENTRY_SHIFT 5
+#define E1000_VFTA_ENTRY_MASK 0x7F
+#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F
+
+#define E1000_HI_MAX_BLOCK_BYTE_LENGTH 1792 /* Num of bytes in range */
+#define E1000_HI_MAX_BLOCK_DWORD_LENGTH 448 /* Num of dwords in range */
+#define E1000_HI_COMMAND_TIMEOUT 500 /* Process HI command limit */
+
+#define E1000_HICR_EN 0x01 /* Enable bit - RO */
+/* Driver sets this bit when done to put command in RAM */
+#define E1000_HICR_C 0x02
+#define E1000_HICR_SV 0x04 /* Status Validity */
+#define E1000_HICR_FW_RESET_ENABLE 0x40
+#define E1000_HICR_FW_RESET 0x80
+
+/* Intel(R) Active Management Technology signature */
+#define E1000_IAMT_SIGNATURE 0x544D4149
+
+#endif
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#include "e1000e.h"
+
+static void e1000e_stop_nvm(struct e1000_hw *hw);
+static void e1000e_reload_nvm(struct e1000_hw *hw);
+
+/**
+ * e1000e_init_nvm_ops_generic - Initialize NVM function pointers
+ * @hw: pointer to the HW structure
+ *
+ * Setups up the function pointers to no-op functions
+ **/
+void e1000e_init_nvm_ops_generic(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ /* Initialize function pointers */
+ nvm->ops.reload = e1000e_reload_nvm;
+}
+
+/**
+ * e1000e_raise_eec_clk - Raise EEPROM clock
+ * @hw: pointer to the HW structure
+ * @eecd: pointer to the EEPROM
+ *
+ * Enable/Raise the EEPROM clock bit.
+ **/
+static void e1000e_raise_eec_clk(struct e1000_hw *hw, u32 *eecd)
+{
+ *eecd = *eecd | E1000_EECD_SK;
+ ew32(EECD, *eecd);
+ e1e_flush();
+ udelay(hw->nvm.delay_usec);
+}
+
+/**
+ * e1000e_lower_eec_clk - Lower EEPROM clock
+ * @hw: pointer to the HW structure
+ * @eecd: pointer to the EEPROM
+ *
+ * Clear/Lower the EEPROM clock bit.
+ **/
+static void e1000e_lower_eec_clk(struct e1000_hw *hw, u32 *eecd)
+{
+ *eecd = *eecd & ~E1000_EECD_SK;
+ ew32(EECD, *eecd);
+ e1e_flush();
+ udelay(hw->nvm.delay_usec);
+}
+
+/**
+ * e1000e_shift_out_eec_bits - Shift data bits our to the EEPROM
+ * @hw: pointer to the HW structure
+ * @data: data to send to the EEPROM
+ * @count: number of bits to shift out
+ *
+ * We need to shift 'count' bits out to the EEPROM. So, the value in the
+ * "data" parameter will be shifted out to the EEPROM one bit at a time.
+ * In order to do this, "data" must be broken down into bits.
+ **/
+static void e1000e_shift_out_eec_bits(struct e1000_hw *hw, u16 data, u16 count)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 eecd = er32(EECD);
+ u32 mask;
+
+ mask = 0x01 << (count - 1);
+ if (nvm->type == e1000_nvm_eeprom_spi)
+ eecd |= E1000_EECD_DO;
+
+ do {
+ eecd &= ~E1000_EECD_DI;
+
+ if (data & mask)
+ eecd |= E1000_EECD_DI;
+
+ ew32(EECD, eecd);
+ e1e_flush();
+
+ udelay(nvm->delay_usec);
+
+ e1000e_raise_eec_clk(hw, &eecd);
+ e1000e_lower_eec_clk(hw, &eecd);
+
+ mask >>= 1;
+ } while (mask);
+
+ eecd &= ~E1000_EECD_DI;
+ ew32(EECD, eecd);
+}
+
+/**
+ * e1000e_shift_in_eec_bits - Shift data bits in from the EEPROM
+ * @hw: pointer to the HW structure
+ * @count: number of bits to shift in
+ *
+ * In order to read a register from the EEPROM, we need to shift 'count' bits
+ * in from the EEPROM. Bits are "shifted in" by raising the clock input to
+ * the EEPROM (setting the SK bit), and then reading the value of the data out
+ * "DO" bit. During this "shifting in" process the data in "DI" bit should
+ * always be clear.
+ **/
+static u16 e1000e_shift_in_eec_bits(struct e1000_hw *hw, u16 count)
+{
+ u32 eecd;
+ u32 i;
+ u16 data;
+
+ eecd = er32(EECD);
+ eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
+ data = 0;
+
+ for (i = 0; i < count; i++) {
+ data <<= 1;
+ e1000e_raise_eec_clk(hw, &eecd);
+
+ eecd = er32(EECD);
+
+ eecd &= ~E1000_EECD_DI;
+ if (eecd & E1000_EECD_DO)
+ data |= 1;
+
+ e1000e_lower_eec_clk(hw, &eecd);
+ }
+
+ return data;
+}
+
+/**
+ * e1000e_poll_eerd_eewr_done - Poll for EEPROM read/write completion
+ * @hw: pointer to the HW structure
+ * @ee_reg: EEPROM flag for polling
+ *
+ * Polls the EEPROM status bit for either read or write completion based
+ * upon the value of 'ee_reg'.
+ **/
+s32 e1000e_poll_eerd_eewr_done(struct e1000_hw *hw, int ee_reg)
+{
+ u32 attempts = 100000;
+ u32 i, reg = 0;
+ s32 ret_val = -E1000_ERR_NVM;
+
+ for (i = 0; i < attempts; i++) {
+ if (ee_reg == E1000_NVM_POLL_READ)
+ reg = er32(EERD);
+ else
+ reg = er32(EEWR);
+
+ if (reg & E1000_NVM_RW_REG_DONE) {
+ ret_val = E1000_SUCCESS;
+ break;
+ }
+
+ udelay(5);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_acquire_nvm - Generic request for access to EEPROM
+ * @hw: pointer to the HW structure
+ *
+ * Set the EEPROM access request bit and wait for EEPROM access grant bit.
+ * Return successful if access grant bit set, else clear the request for
+ * EEPROM access and return -E1000_ERR_NVM (-1).
+ **/
+s32 e1000e_acquire_nvm(struct e1000_hw *hw)
+{
+ u32 eecd = er32(EECD);
+ s32 timeout = E1000_NVM_GRANT_ATTEMPTS;
+ s32 ret_val = E1000_SUCCESS;
+
+ ew32(EECD, eecd | E1000_EECD_REQ);
+ eecd = er32(EECD);
+ while (timeout) {
+ if (eecd & E1000_EECD_GNT)
+ break;
+ udelay(5);
+ eecd = er32(EECD);
+ timeout--;
+ }
+
+ if (!timeout) {
+ eecd &= ~E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ e_dbg("Could not acquire NVM grant\n");
+ ret_val = -E1000_ERR_NVM;
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_standby_nvm - Return EEPROM to standby state
+ * @hw: pointer to the HW structure
+ *
+ * Return the EEPROM to a standby state.
+ **/
+static void e1000e_standby_nvm(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 eecd = er32(EECD);
+
+ if (nvm->type == e1000_nvm_eeprom_spi) {
+ /* Toggle CS to flush commands */
+ eecd |= E1000_EECD_CS;
+ ew32(EECD, eecd);
+ e1e_flush();
+ udelay(nvm->delay_usec);
+ eecd &= ~E1000_EECD_CS;
+ ew32(EECD, eecd);
+ e1e_flush();
+ udelay(nvm->delay_usec);
+ }
+}
+
+/**
+ * e1000e_stop_nvm - Terminate EEPROM command
+ * @hw: pointer to the HW structure
+ *
+ * Terminates the current command by inverting the EEPROM's chip select pin.
+ **/
+static void e1000e_stop_nvm(struct e1000_hw *hw)
+{
+ u32 eecd;
+
+ eecd = er32(EECD);
+ if (hw->nvm.type == e1000_nvm_eeprom_spi) {
+ /* Pull CS high */
+ eecd |= E1000_EECD_CS;
+ e1000e_lower_eec_clk(hw, &eecd);
+ }
+}
+
+/**
+ * e1000e_release_nvm - Release exclusive access to EEPROM
+ * @hw: pointer to the HW structure
+ *
+ * Stop any current commands to the EEPROM and clear the EEPROM request bit.
+ **/
+void e1000e_release_nvm(struct e1000_hw *hw)
+{
+ u32 eecd;
+
+ e1000e_stop_nvm(hw);
+
+ eecd = er32(EECD);
+ eecd &= ~E1000_EECD_REQ;
+ ew32(EECD, eecd);
+}
+
+/**
+ * e1000e_ready_nvm_eeprom - Prepares EEPROM for read/write
+ * @hw: pointer to the HW structure
+ *
+ * Setups the EEPROM for reading and writing.
+ **/
+static s32 e1000e_ready_nvm_eeprom(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 eecd = er32(EECD);
+ s32 ret_val = E1000_SUCCESS;
+ u16 timeout = 0;
+ u8 spi_stat_reg;
+
+ if (nvm->type == e1000_nvm_eeprom_spi) {
+ /* Clear SK and CS */
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+ ew32(EECD, eecd);
+ udelay(1);
+ timeout = NVM_MAX_RETRY_SPI;
+
+ /*
+ * Read "Status Register" repeatedly until the LSB is cleared.
+ * The EEPROM will signal that the command has been completed
+ * by clearing bit 0 of the internal status register. If it's
+ * not cleared within 'timeout', then error out.
+ */
+ while (timeout) {
+ e1000e_shift_out_eec_bits(hw, NVM_RDSR_OPCODE_SPI,
+ hw->nvm.opcode_bits);
+ spi_stat_reg = (u8)e1000e_shift_in_eec_bits(hw, 8);
+ if (!(spi_stat_reg & NVM_STATUS_RDY_SPI))
+ break;
+
+ udelay(5);
+ e1000e_standby_nvm(hw);
+ timeout--;
+ }
+
+ if (!timeout) {
+ e_dbg("SPI NVM Status error\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_nvm_eerd - Reads EEPROM using EERD register
+ * @hw: pointer to the HW structure
+ * @offset: offset of word in the EEPROM to read
+ * @words: number of words to read
+ * @data: word read from the EEPROM
+ *
+ * Reads a 16 bit word from the EEPROM using the EERD register.
+ **/
+s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 i, eerd = 0;
+ s32 ret_val = E1000_SUCCESS;
+
+ /*
+ * A check for invalid values: offset too large, too many words,
+ * too many words for the offset, and not enough words.
+ */
+ if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) ||
+ (words == 0)) {
+ e_dbg("nvm parameter(s) out of bounds\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+ for (i = 0; i < words; i++) {
+ eerd = ((offset+i) << E1000_NVM_RW_ADDR_SHIFT) +
+ E1000_NVM_RW_REG_START;
+
+ ew32(EERD, eerd);
+ ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_READ);
+ if (ret_val)
+ break;
+
+ data[i] = (er32(EERD) >>
+ E1000_NVM_RW_REG_DATA);
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_write_nvm_spi - Write to EEPROM using SPI
+ * @hw: pointer to the HW structure
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: 16 bit word(s) to be written to the EEPROM
+ *
+ * Writes data to EEPROM at offset using SPI interface.
+ *
+ * If e1000e_update_nvm_checksum is not called after this function , the
+ * EEPROM will most likely contain an invalid checksum.
+ **/
+s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ s32 ret_val;
+ u16 widx = 0;
+
+ /*
+ * A check for invalid values: offset too large, too many words,
+ * and not enough words.
+ */
+ if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) ||
+ (words == 0)) {
+ e_dbg("nvm parameter(s) out of bounds\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+ ret_val = nvm->ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ while (widx < words) {
+ u8 write_opcode = NVM_WRITE_OPCODE_SPI;
+
+ ret_val = e1000e_ready_nvm_eeprom(hw);
+ if (ret_val)
+ goto release;
+
+ e1000e_standby_nvm(hw);
+
+ /* Send the WRITE ENABLE command (8 bit opcode) */
+ e1000e_shift_out_eec_bits(hw, NVM_WREN_OPCODE_SPI,
+ nvm->opcode_bits);
+
+ e1000e_standby_nvm(hw);
+
+ /*
+ * Some SPI eeproms use the 8th address bit embedded in the
+ * opcode
+ */
+ if ((nvm->address_bits == 8) && (offset >= 128))
+ write_opcode |= NVM_A8_OPCODE_SPI;
+
+ /* Send the Write command (8-bit opcode + addr) */
+ e1000e_shift_out_eec_bits(hw, write_opcode, nvm->opcode_bits);
+ e1000e_shift_out_eec_bits(hw, (u16)((offset + widx) * 2),
+ nvm->address_bits);
+
+ /* Loop to allow for up to whole page write of eeprom */
+ while (widx < words) {
+ u16 word_out = data[widx];
+ word_out = (word_out >> 8) | (word_out << 8);
+ e1000e_shift_out_eec_bits(hw, word_out, 16);
+ widx++;
+
+ if ((((offset + widx) * 2) % nvm->page_size) == 0) {
+ e1000e_standby_nvm(hw);
+ break;
+ }
+ }
+ }
+
+ msleep(10);
+release:
+ nvm->ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_pba_num - Read device part number
+ * @hw: pointer to the HW structure
+ * @pba_num: pointer to device part number
+ *
+ * Reads the product board assembly (PBA) number from the EEPROM and stores
+ * the value in pba_num.
+ **/
+s32 e1000e_read_pba_num(struct e1000_hw *hw, u32 *pba_num)
+{
+ s32 ret_val;
+ u16 nvm_data;
+
+ ret_val = e1000e_read_nvm(hw, NVM_PBA_OFFSET_0, 1, &nvm_data);
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ goto out;
+ }
+ *pba_num = (u32)(nvm_data << 16);
+
+ ret_val = e1000e_read_nvm(hw, NVM_PBA_OFFSET_1, 1, &nvm_data);
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ goto out;
+ }
+ *pba_num |= nvm_data;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_mac_addr_generic - Read device MAC address
+ * @hw: pointer to the HW structure
+ *
+ * Reads the device MAC address from the EEPROM and stores the value.
+ * Since devices with two ports use the same EEPROM, we increment the
+ * last bit in the MAC address for the second port.
+ **/
+s32 e1000e_read_mac_addr_generic(struct e1000_hw *hw)
+{
+ u32 rar_high;
+ u32 rar_low;
+ u16 i;
+
+ rar_high = er32(RAH(0));
+ rar_low = er32(RAL(0));
+
+ for (i = 0; i < E1000_RAL_MAC_ADDR_LEN; i++)
+ hw->mac.perm_addr[i] = (u8)(rar_low >> (i*8));
+
+ for (i = 0; i < E1000_RAH_MAC_ADDR_LEN; i++)
+ hw->mac.perm_addr[i+4] = (u8)(rar_high >> (i*8));
+
+ for (i = 0; i < ETH_ADDR_LEN; i++)
+ hw->mac.addr[i] = hw->mac.perm_addr[i];
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_validate_nvm_checksum_generic - Validate EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Calculates the EEPROM checksum by reading/adding each word of the EEPROM
+ * and then verifies that the sum of the EEPROM is equal to 0xBABA.
+ **/
+s32 e1000e_validate_nvm_checksum_generic(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 checksum = 0;
+ u16 i, nvm_data;
+
+ for (i = 0; i < (NVM_CHECKSUM_REG + 1); i++) {
+ ret_val = e1000e_read_nvm(hw, i, 1, &nvm_data);
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ goto out;
+ }
+ checksum += nvm_data;
+ }
+
+ if (checksum != (u16) NVM_SUM) {
+ e_dbg("NVM Checksum Invalid\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_update_nvm_checksum_generic - Update EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Updates the EEPROM checksum by reading/adding each word of the EEPROM
+ * up to the checksum. Then calculates the EEPROM checksum and writes the
+ * value to the EEPROM.
+ **/
+s32 e1000e_update_nvm_checksum_generic(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 checksum = 0;
+ u16 i, nvm_data;
+
+ for (i = 0; i < NVM_CHECKSUM_REG; i++) {
+ ret_val = e1000e_read_nvm(hw, i, 1, &nvm_data);
+ if (ret_val) {
+ e_dbg("NVM Read Error while updating checksum.\n");
+ goto out;
+ }
+ checksum += nvm_data;
+ }
+ checksum = (u16) NVM_SUM - checksum;
+ ret_val = e1000e_write_nvm(hw, NVM_CHECKSUM_REG, 1, &checksum);
+ if (ret_val)
+ e_dbg("NVM Write Error while updating checksum.\n");
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_reload_nvm - Reloads EEPROM
+ * @hw: pointer to the HW structure
+ *
+ * Reloads the EEPROM by setting the "Reinitialize from EEPROM" bit in the
+ * extended control register.
+ **/
+static void e1000e_reload_nvm(struct e1000_hw *hw)
+{
+ u32 ctrl_ext;
+
+ udelay(10);
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+ ew32(CTRL_EXT, ctrl_ext);
+ e1e_flush();
+}
+
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#ifndef _E1000E_NVM_H_
+#define _E1000E_NVM_H_
+
+void e1000e_init_nvm_ops_generic(struct e1000_hw *hw);
+s32 e1000e_acquire_nvm(struct e1000_hw *hw);
+
+s32 e1000e_poll_eerd_eewr_done(struct e1000_hw *hw, int ee_reg);
+s32 e1000e_read_mac_addr_generic(struct e1000_hw *hw);
+s32 e1000e_read_pba_num(struct e1000_hw *hw, u32 *pba_num);
+s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data);
+s32 e1000e_valid_led_default(struct e1000_hw *hw, u16 *data);
+s32 e1000e_validate_nvm_checksum_generic(struct e1000_hw *hw);
+s32 e1000e_write_nvm_eewr(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data);
+s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data);
+s32 e1000e_update_nvm_checksum_generic(struct e1000_hw *hw);
+void e1000e_release_nvm(struct e1000_hw *hw);
+
+#define E1000_STM_OPCODE 0xDB00
+
+#endif
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#include "e1000e.h"
+
+static s32 e1000e_copper_link_autoneg(struct e1000_hw *hw);
+static s32 e1000e_phy_setup_autoneg(struct e1000_hw *hw);
+static u32 e1000e_get_phy_addr_for_bm_page(u32 page, u32 reg);
+static s32 e1000e_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read);
+static u32 e1000e_get_phy_addr_for_hv_page(u32 page);
+static s32 e1000e_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read);
+#if 0
+/* Cable length tables */
+static const u16 e1000_m88_cable_length_table[] =
+ { 0, 50, 80, 110, 140, 140, E1000_CABLE_LENGTH_UNDEFINED };
+#define M88E1000_CABLE_LENGTH_TABLE_SIZE \
+ (sizeof(e1000_m88_cable_length_table) / \
+ sizeof(e1000_m88_cable_length_table[0]))
+
+static const u16 e1000_igp_2_cable_length_table[] =
+ { 0, 0, 0, 0, 0, 0, 0, 0, 3, 5, 8, 11, 13, 16, 18, 21,
+ 0, 0, 0, 3, 6, 10, 13, 16, 19, 23, 26, 29, 32, 35, 38, 41,
+ 6, 10, 14, 18, 22, 26, 30, 33, 37, 41, 44, 48, 51, 54, 58, 61,
+ 21, 26, 31, 35, 40, 44, 49, 53, 57, 61, 65, 68, 72, 75, 79, 82,
+ 40, 45, 51, 56, 61, 66, 70, 75, 79, 83, 87, 91, 94, 98, 101, 104,
+ 60, 66, 72, 77, 82, 87, 92, 96, 100, 104, 108, 111, 114, 117, 119, 121,
+ 83, 89, 95, 100, 105, 109, 113, 116, 119, 122, 124,
+ 104, 109, 114, 118, 121, 124};
+#define IGP02E1000_CABLE_LENGTH_TABLE_SIZE \
+ (sizeof(e1000_igp_2_cable_length_table) / \
+ sizeof(e1000_igp_2_cable_length_table[0]))
+#endif
+
+/**
+ * e1000e_check_reset_block_generic - Check if PHY reset is blocked
+ * @hw: pointer to the HW structure
+ *
+ * Read the PHY management control register and check whether a PHY reset
+ * is blocked. If a reset is not blocked return E1000_SUCCESS, otherwise
+ * return E1000_BLK_PHY_RESET (12).
+ **/
+s32 e1000e_check_reset_block_generic(struct e1000_hw *hw)
+{
+ u32 manc;
+
+ manc = er32(MANC);
+
+ return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ?
+ E1000_BLK_PHY_RESET : E1000_SUCCESS;
+}
+
+/**
+ * e1000e_get_phy_id - Retrieve the PHY ID and revision
+ * @hw: pointer to the HW structure
+ *
+ * Reads the PHY registers and stores the PHY ID and possibly the PHY
+ * revision in the hardware structure.
+ **/
+s32 e1000e_get_phy_id(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+ u16 phy_id;
+ u16 retry_count = 0;
+
+ if (!(phy->ops.read_reg))
+ goto out;
+
+ while (retry_count < 2) {
+ ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+ if (ret_val)
+ goto out;
+
+ phy->id = (u32)(phy_id << 16);
+ udelay(20);
+ ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+ if (ret_val)
+ goto out;
+
+ phy->id |= (u32)(phy_id & PHY_REVISION_MASK);
+ phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+
+ if (phy->id != 0 && phy->id != PHY_REVISION_MASK)
+ goto out;
+
+ /*
+ * If the PHY ID is still unknown, we may have an 82577
+ * without link. We will try again after setting Slow MDIC
+ * mode. No harm in trying again in this case since the PHY
+ * ID is unknown at this point anyway.
+ */
+ ret_val = phy->ops.acquire(hw);
+ if (ret_val)
+ goto out;
+ ret_val = e1000e_set_mdio_slow_mode_hv(hw, true);
+ if (ret_val)
+ goto out;
+ phy->ops.release(hw);
+
+ retry_count++;
+ }
+out:
+ /* Revert to MDIO fast mode, if applicable */
+ if (retry_count) {
+ ret_val = phy->ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000e_set_mdio_slow_mode_hv(hw, false);
+ phy->ops.release(hw);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_phy_reset_dsp - Reset PHY DSP
+ * @hw: pointer to the HW structure
+ *
+ * Reset the digital signal processor.
+ **/
+s32 e1000e_phy_reset_dsp(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ if (!(hw->phy.ops.write_reg))
+ goto out;
+
+ ret_val = e1e_wphy(hw, M88E1000_PHY_GEN_CONTROL, 0xC1);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1e_wphy(hw, M88E1000_PHY_GEN_CONTROL, 0);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_phy_reg_mdic - Read MDI control register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the MDI control register in the PHY at offset and stores the
+ * information read to data.
+ **/
+s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 i, mdic = 0;
+ s32 ret_val = E1000_SUCCESS;
+
+ /*
+ * Set up Op-code, Phy Address, and register offset in the MDI
+ * Control register. The MAC will take care of interfacing with the
+ * PHY to retrieve the desired data.
+ */
+ mdic = ((offset << E1000_MDIC_REG_SHIFT) |
+ (phy->addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_READ));
+
+ ew32(MDIC, mdic);
+
+ /*
+ * Poll the ready bit to see if the MDI read completed
+ * Increasing the time out as testing showed failures with
+ * the lower time out
+ */
+ for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
+ udelay(50);
+ mdic = er32(MDIC);
+ if (mdic & E1000_MDIC_READY)
+ break;
+ }
+ if (!(mdic & E1000_MDIC_READY)) {
+ e_dbg("MDI Read did not complete\n");
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+ if (mdic & E1000_MDIC_ERROR) {
+ e_dbg("MDI Error\n");
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+ *data = (u16) mdic;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_write_phy_reg_mdic - Write MDI control register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write to register at offset
+ *
+ * Writes data to MDI control register in the PHY at offset.
+ **/
+s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 i, mdic = 0;
+ s32 ret_val = E1000_SUCCESS;
+
+ /*
+ * Set up Op-code, Phy Address, and register offset in the MDI
+ * Control register. The MAC will take care of interfacing with the
+ * PHY to retrieve the desired data.
+ */
+ mdic = (((u32)data) |
+ (offset << E1000_MDIC_REG_SHIFT) |
+ (phy->addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_WRITE));
+
+ ew32(MDIC, mdic);
+
+ /*
+ * Poll the ready bit to see if the MDI read completed
+ * Increasing the time out as testing showed failures with
+ * the lower time out
+ */
+ for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
+ udelay(50);
+ mdic = er32(MDIC);
+ if (mdic & E1000_MDIC_READY)
+ break;
+ }
+ if (!(mdic & E1000_MDIC_READY)) {
+ e_dbg("MDI Write did not complete\n");
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+ if (mdic & E1000_MDIC_ERROR) {
+ e_dbg("MDI Error\n");
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_phy_reg_m88 - Read m88 PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting.
+ **/
+s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ if (!(hw->phy.ops.acquire))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_write_phy_reg_m88 - Write m88 PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ if (!(hw->phy.ops.acquire))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * __e1000e_read_phy_reg_igp - Read igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ * @locked: semaphore has already been acquired or not
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and stores the retrieved information in data. Release any acquired
+ * semaphores before exiting.
+ **/
+static s32 __e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data,
+ bool locked)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ if (!locked) {
+ if (!(hw->phy.ops.acquire))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (u16)offset);
+ if (ret_val)
+ goto release;
+ }
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+release:
+ if (!locked)
+ hw->phy.ops.release(hw);
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_phy_reg_igp - Read igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore then reads the PHY register at offset and stores the
+ * retrieved information in data.
+ * Release the acquired semaphore before exiting.
+ **/
+s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000e_read_phy_reg_igp(hw, offset, data, false);
+}
+
+/**
+ * e1000e_read_phy_reg_igp_locked - Read igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the PHY register at offset and stores the retrieved information
+ * in data. Assumes semaphore already acquired.
+ **/
+s32 e1000e_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000e_read_phy_reg_igp(hw, offset, data, true);
+}
+
+/**
+ * e1000e_write_phy_reg_igp - Write igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ * @locked: semaphore has already been acquired or not
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+static s32 __e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data,
+ bool locked)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ if (!locked) {
+ if (!(hw->phy.ops.acquire))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (u16)offset);
+ if (ret_val)
+ goto release;
+ }
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+release:
+ if (!locked)
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_write_phy_reg_igp - Write igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000e_write_phy_reg_igp(hw, offset, data, false);
+}
+
+/**
+ * e1000e_write_phy_reg_igp_locked - Write igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Writes the data to PHY register at the offset.
+ * Assumes semaphore already acquired.
+ **/
+s32 e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000e_write_phy_reg_igp(hw, offset, data, true);
+}
+
+/**
+ * __e1000e_read_kmrn_reg - Read kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ * @locked: semaphore has already been acquired or not
+ *
+ * Acquires semaphore, if necessary. Then reads the PHY register at offset
+ * using the kumeran interface. The information retrieved is stored in data.
+ * Release any acquired semaphores before exiting.
+ **/
+static s32 __e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data,
+ bool locked)
+{
+ u32 kmrnctrlsta;
+ s32 ret_val = E1000_SUCCESS;
+
+ if (!locked) {
+ if (!(hw->phy.ops.acquire))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
+ E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN;
+ ew32(KMRNCTRLSTA, kmrnctrlsta);
+
+ udelay(2);
+
+ kmrnctrlsta = er32(KMRNCTRLSTA);
+ *data = (u16)kmrnctrlsta;
+
+ if (!locked)
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_kmrn_reg - Read kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore then reads the PHY register at offset using the
+ * kumeran interface. The information retrieved is stored in data.
+ * Release the acquired semaphore before exiting.
+ **/
+s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000e_read_kmrn_reg(hw, offset, data, false);
+}
+
+/**
+ * e1000e_read_kmrn_reg_locked - Read kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the PHY register at offset using the kumeran interface. The
+ * information retrieved is stored in data.
+ * Assumes semaphore already acquired.
+ **/
+s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000e_read_kmrn_reg(hw, offset, data, true);
+}
+
+/**
+ * __e1000e_write_kmrn_reg - Write kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ * @locked: semaphore has already been acquired or not
+ *
+ * Acquires semaphore, if necessary. Then write the data to PHY register
+ * at the offset using the kumeran interface. Release any acquired semaphores
+ * before exiting.
+ **/
+static s32 __e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data,
+ bool locked)
+{
+ u32 kmrnctrlsta;
+ s32 ret_val = E1000_SUCCESS;
+
+ if (!locked) {
+ if (!(hw->phy.ops.acquire))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
+ E1000_KMRNCTRLSTA_OFFSET) | data;
+ ew32(KMRNCTRLSTA, kmrnctrlsta);
+
+ udelay(2);
+
+ if (!locked)
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_write_kmrn_reg - Write kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore then writes the data to the PHY register at the offset
+ * using the kumeran interface. Release the acquired semaphore before exiting.
+ **/
+s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000e_write_kmrn_reg(hw, offset, data, false);
+}
+
+/**
+ * e1000e_write_kmrn_reg_locked - Write kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Write the data to PHY register at the offset using the kumeran interface.
+ * Assumes semaphore already acquired.
+ **/
+s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000e_write_kmrn_reg(hw, offset, data, true);
+}
+
+/**
+ * e1000e_copper_link_setup_82577 - Setup 82577 PHY for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Sets up Carrier-sense on Transmit and downshift values.
+ **/
+s32 e1000e_copper_link_setup_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+
+ if (phy->reset_disable) {
+ ret_val = E1000_SUCCESS;
+ goto out;
+ }
+
+ /* Enable CRS on TX. This must be set for half-duplex operation. */
+ ret_val = e1e_rphy(hw, I82577_CFG_REG, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data |= I82577_CFG_ASSERT_CRS_ON_TX;
+
+ /* Enable downshift */
+ phy_data |= I82577_CFG_ENABLE_DOWNSHIFT;
+
+ ret_val = e1e_wphy(hw, I82577_CFG_REG, phy_data);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_copper_link_setup_m88 - Setup m88 PHY's for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Sets up MDI/MDI-X and polarity for m88 PHY's. If necessary, transmit clock
+ * and downshift values are set also.
+ **/
+s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+
+ if (phy->reset_disable) {
+ ret_val = E1000_SUCCESS;
+ goto out;
+ }
+
+ /* Enable CRS on TX. This must be set for half-duplex operation. */
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ /* For BM PHY this bit is downshift enable */
+ if (phy->type != e1000_phy_bm)
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+
+ /*
+ * Options:
+ * MDI/MDI-X = 0 (default)
+ * 0 - Auto for all speeds
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+ */
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+
+ switch (phy->mdix) {
+ case 1:
+ phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
+ break;
+ case 2:
+ phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
+ break;
+ case 3:
+ phy_data |= M88E1000_PSCR_AUTO_X_1000T;
+ break;
+ case 0:
+ default:
+ phy_data |= M88E1000_PSCR_AUTO_X_MODE;
+ break;
+ }
+
+ /*
+ * Options:
+ * disable_polarity_correction = 0 (default)
+ * Automatic Correction for Reversed Cable Polarity
+ * 0 - Disabled
+ * 1 - Enabled
+ */
+ phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
+ if (phy->disable_polarity_correction == 1)
+ phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
+
+ /* Enable downshift on BM (disabled by default) */
+ if (phy->type == e1000_phy_bm)
+ phy_data |= BME1000_PSCR_ENABLE_DOWNSHIFT;
+
+ ret_val = e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ goto out;
+
+ if ((phy->type == e1000_phy_m88) &&
+ (phy->revision < E1000_REVISION_4) &&
+ (phy->id != BME1000_E_PHY_ID_R2)) {
+ /*
+ * Force TX_CLK in the Extended PHY Specific Control Register
+ * to 25MHz clock.
+ */
+ ret_val = e1e_rphy(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+
+ if ((phy->revision == E1000_REVISION_2) &&
+ (phy->id == M88E1111_I_PHY_ID)) {
+ /* 82573L PHY - set the downshift counter to 5x. */
+ phy_data &= ~M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK;
+ phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X;
+ } else {
+ /* Configure Master and Slave downshift values */
+ phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
+ M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
+ phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
+ M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
+ }
+ ret_val = e1e_wphy(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ goto out;
+ }
+
+ if ((phy->type == e1000_phy_bm) && (phy->id == BME1000_E_PHY_ID_R2)) {
+ /* Set PHY page 0, register 29 to 0x0003 */
+ ret_val = e1e_wphy(hw, 29, 0x0003);
+ if (ret_val)
+ goto out;
+
+ /* Set PHY page 0, register 30 to 0x0000 */
+ ret_val = e1e_wphy(hw, 30, 0x0000);
+ if (ret_val)
+ goto out;
+ }
+
+ /* Commit the changes. */
+ ret_val = e1000e_commit_phy(hw);
+ if (ret_val) {
+ e_dbg("Error committing the PHY changes\n");
+ goto out;
+ }
+
+ if (phy->type == e1000_phy_82578) {
+ ret_val = e1e_rphy(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ /* 82578 PHY - set the downshift count to 1x. */
+ phy_data |= I82578_EPSCR_DOWNSHIFT_ENABLE;
+ phy_data &= ~I82578_EPSCR_DOWNSHIFT_COUNTER_MASK;
+ ret_val = e1e_wphy(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_copper_link_setup_igp - Setup igp PHY's for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Sets up LPLU, MDI/MDI-X, polarity, Smartspeed and Master/Slave config for
+ * igp PHY's.
+ **/
+s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+
+ if (phy->reset_disable) {
+ ret_val = E1000_SUCCESS;
+ goto out;
+ }
+
+ ret_val = e1000e_phy_hw_reset(hw);
+ if (ret_val) {
+ e_dbg("Error resetting the PHY.\n");
+ goto out;
+ }
+
+ /*
+ * Wait 100ms for MAC to configure PHY from NVM settings, to avoid
+ * timeout issues when LFS is enabled.
+ */
+ msleep(100);
+
+ /*
+ * The NVM settings will configure LPLU in D3 for
+ * non-IGP1 PHYs.
+ */
+ if (phy->type == e1000_phy_igp) {
+ /* disable lplu d3 during driver init */
+ ret_val = hw->phy.ops.set_d3_lplu_state(hw, false);
+ if (ret_val) {
+ e_dbg("Error Disabling LPLU D3\n");
+ goto out;
+ }
+ }
+
+ /* disable lplu d0 during driver init */
+ if (hw->phy.ops.set_d0_lplu_state) {
+ ret_val = hw->phy.ops.set_d0_lplu_state(hw, false);
+ if (ret_val) {
+ e_dbg("Error Disabling LPLU D0\n");
+ goto out;
+ }
+ }
+ /* Configure mdi-mdix settings */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CTRL, &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+
+ switch (phy->mdix) {
+ case 1:
+ data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 2:
+ data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 0:
+ default:
+ data |= IGP01E1000_PSCR_AUTO_MDIX;
+ break;
+ }
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CTRL, data);
+ if (ret_val)
+ goto out;
+
+ /* set auto-master slave resolution settings */
+ if (hw->mac.autoneg) {
+ /*
+ * when autonegotiation advertisement is only 1000Mbps then we
+ * should disable SmartSpeed and enable Auto MasterSlave
+ * resolution as hardware default.
+ */
+ if (phy->autoneg_advertised == ADVERTISE_1000_FULL) {
+ /* Disable SmartSpeed */
+ ret_val = e1e_rphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ goto out;
+
+ /* Set auto Master/Slave resolution process */
+ ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~CR_1000T_MS_ENABLE;
+ ret_val = e1e_wphy(hw, PHY_1000T_CTRL, data);
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &data);
+ if (ret_val)
+ goto out;
+
+ /* load defaults for future use */
+ phy->original_ms_type = (data & CR_1000T_MS_ENABLE) ?
+ ((data & CR_1000T_MS_VALUE) ?
+ e1000_ms_force_master :
+ e1000_ms_force_slave) :
+ e1000_ms_auto;
+
+ switch (phy->ms_type) {
+ case e1000_ms_force_master:
+ data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_force_slave:
+ data |= CR_1000T_MS_ENABLE;
+ data &= ~(CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_auto:
+ data &= ~CR_1000T_MS_ENABLE;
+ default:
+ break;
+ }
+ ret_val = e1e_wphy(hw, PHY_1000T_CTRL, data);
+ if (ret_val)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_copper_link_autoneg - Setup/Enable autoneg for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Performs initial bounds checking on autoneg advertisement parameter, then
+ * configure to advertise the full capability. Setup the PHY to autoneg
+ * and restart the negotiation process between the link partner. If
+ * autoneg_wait_to_complete, then wait for autoneg to complete before exiting.
+ **/
+static s32 e1000e_copper_link_autoneg(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_ctrl;
+
+ /*
+ * Perform some bounds checking on the autoneg advertisement
+ * parameter.
+ */
+ phy->autoneg_advertised &= phy->autoneg_mask;
+
+ /*
+ * If autoneg_advertised is zero, we assume it was not defaulted
+ * by the calling code so we set to advertise full capability.
+ */
+ if (phy->autoneg_advertised == 0)
+ phy->autoneg_advertised = phy->autoneg_mask;
+
+ e_dbg("Reconfiguring auto-neg advertisement params\n");
+ ret_val = e1000e_phy_setup_autoneg(hw);
+ if (ret_val) {
+ e_dbg("Error Setting up Auto-Negotiation\n");
+ goto out;
+ }
+ e_dbg("Restarting Auto-Neg\n");
+
+ /*
+ * Restart auto-negotiation by setting the Auto Neg Enable bit and
+ * the Auto Neg Restart bit in the PHY control register.
+ */
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_ctrl);
+ if (ret_val)
+ goto out;
+
+ phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
+ ret_val = e1e_wphy(hw, PHY_CONTROL, phy_ctrl);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Does the user want to wait for Auto-Neg to complete here, or
+ * check at a later time (for example, callback routine).
+ */
+ if (phy->autoneg_wait_to_complete) {
+ ret_val = hw->mac.ops.wait_autoneg(hw);
+ if (ret_val) {
+ e_dbg("Error while waiting for "
+ "autoneg to complete\n");
+ goto out;
+ }
+ }
+
+ hw->mac.get_link_status = true;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_phy_setup_autoneg - Configure PHY for auto-negotiation
+ * @hw: pointer to the HW structure
+ *
+ * Reads the MII auto-neg advertisement register and/or the 1000T control
+ * register and if the PHY is already setup for auto-negotiation, then
+ * return successful. Otherwise, setup advertisement and flow control to
+ * the appropriate values for the wanted auto-negotiation.
+ **/
+static s32 e1000e_phy_setup_autoneg(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 mii_autoneg_adv_reg;
+ u16 mii_1000t_ctrl_reg = 0;
+
+ phy->autoneg_advertised &= phy->autoneg_mask;
+
+ /* Read the MII Auto-Neg Advertisement Register (Address 4). */
+ ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
+ if (ret_val)
+ goto out;
+
+ if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
+ /* Read the MII 1000Base-T Control Register (Address 9). */
+ ret_val = e1e_rphy(hw, PHY_1000T_CTRL,
+ &mii_1000t_ctrl_reg);
+ if (ret_val)
+ goto out;
+ }
+
+ /*
+ * Need to parse both autoneg_advertised and fc and set up
+ * the appropriate PHY registers. First we will parse for
+ * autoneg_advertised software override. Since we can advertise
+ * a plethora of combinations, we need to check each bit
+ * individually.
+ */
+
+ /*
+ * First we clear all the 10/100 mb speed bits in the Auto-Neg
+ * Advertisement Register (Address 4) and the 1000 mb speed bits in
+ * the 1000Base-T Control Register (Address 9).
+ */
+ mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS |
+ NWAY_AR_100TX_HD_CAPS |
+ NWAY_AR_10T_FD_CAPS |
+ NWAY_AR_10T_HD_CAPS);
+ mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS);
+
+ e_dbg("autoneg_advertised %x\n", phy->autoneg_advertised);
+
+ /* Do we want to advertise 10 Mb Half Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_10_HALF) {
+ e_dbg("Advertise 10mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+ }
+
+ /* Do we want to advertise 10 Mb Full Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_10_FULL) {
+ e_dbg("Advertise 10mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
+ }
+
+ /* Do we want to advertise 100 Mb Half Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_100_HALF) {
+ e_dbg("Advertise 100mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
+ }
+
+ /* Do we want to advertise 100 Mb Full Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_100_FULL) {
+ e_dbg("Advertise 100mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
+ }
+
+ /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
+ if (phy->autoneg_advertised & ADVERTISE_1000_HALF)
+ e_dbg("Advertise 1000mb Half duplex request denied!\n");
+
+ /* Do we want to advertise 1000 Mb Full Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_1000_FULL) {
+ e_dbg("Advertise 1000mb Full duplex\n");
+ mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+ }
+
+ /*
+ * Check for a software override of the flow control settings, and
+ * setup the PHY advertisement registers accordingly. If
+ * auto-negotiation is enabled, then software will have to set the
+ * "PAUSE" bits to the correct value in the Auto-Negotiation
+ * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-
+ * negotiation.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * but we do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ * other: No software override. The flow control configuration
+ * in the EEPROM is used.
+ */
+ switch (hw->fc.current_mode) {
+ case e1000_fc_none:
+ /*
+ * Flow control (Rx & Tx) is completely disabled by a
+ * software over-ride.
+ */
+ mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ case e1000_fc_rx_pause:
+ /*
+ * Rx Flow control is enabled, and Tx Flow control is
+ * disabled, by a software over-ride.
+ *
+ * Since there really isn't a way to advertise that we are
+ * capable of Rx Pause ONLY, we will advertise that we
+ * support both symmetric and asymmetric Rx PAUSE. Later
+ * (in e1000e_config_fc_after_link_up) we will disable the
+ * hw's ability to send PAUSE frames.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ case e1000_fc_tx_pause:
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is
+ * disabled, by a software over-ride.
+ */
+ mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
+ mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
+ break;
+ case e1000_fc_full:
+ /*
+ * Flow control (both Rx and Tx) is enabled by a software
+ * over-ride.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ default:
+ e_dbg("Flow control param set incorrectly\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ ret_val = e1e_wphy(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+ if (ret_val)
+ goto out;
+
+ e_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
+
+ if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
+ ret_val = e1e_wphy(hw,
+ PHY_1000T_CTRL,
+ mii_1000t_ctrl_reg);
+ if (ret_val)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_setup_copper_link - Configure copper link settings
+ * @hw: pointer to the HW structure
+ *
+ * Calls the appropriate function to configure the link for auto-neg or forced
+ * speed and duplex. Then we check for link, once link is established calls
+ * to configure collision distance and flow control are called. If link is
+ * not established, we return -E1000_ERR_PHY (-2).
+ **/
+s32 e1000e_setup_copper_link(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ bool link;
+
+ if (hw->mac.autoneg) {
+ /*
+ * Setup autoneg and flow control advertisement and perform
+ * autonegotiation.
+ */
+ ret_val = e1000e_copper_link_autoneg(hw);
+ if (ret_val)
+ goto out;
+ } else {
+#if 0
+ /*
+ * PHY will be set to 10H, 10F, 100H or 100F
+ * depending on user settings.
+ */
+ e_dbg("Forcing Speed and Duplex\n");
+ ret_val = hw->phy.ops.force_speed_duplex(hw);
+ if (ret_val) {
+ e_dbg("Error Forcing Speed and Duplex\n");
+ goto out;
+ }
+#endif
+ }
+
+ /*
+ * Check link status. Wait up to 100 microseconds for link to become
+ * valid.
+ */
+ ret_val = e1000e_phy_has_link_generic(hw,
+ COPPER_LINK_UP_LIMIT,
+ 10,
+ &link);
+ if (ret_val)
+ goto out;
+
+ if (link) {
+ e_dbg("Valid link established!!!\n");
+ e1000e_config_collision_dist(hw);
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ } else {
+ e_dbg("Unable to establish link!!!\n");
+ }
+
+out:
+ return ret_val;
+}
+
+#if 0
+/**
+ * e1000e_phy_force_speed_duplex_igp - Force speed/duplex for igp PHY
+ * @hw: pointer to the HW structure
+ *
+ * Calls the PHY setup function to force speed and duplex. Clears the
+ * auto-crossover to force MDI manually. Waits for link and returns
+ * successful if link up is successful, else -E1000_ERR_PHY (-2).
+ **/
+s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
+
+ ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Clear Auto-Crossover to force MDI manually. IGP requires MDI
+ * forced whenever speed and duplex are forced.
+ */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+ phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ if (ret_val)
+ goto out;
+
+ e_dbg("IGP PSCR: %X\n", phy_data);
+
+ udelay(1);
+
+ if (phy->autoneg_wait_to_complete) {
+ e_dbg("Waiting for forced speed/duplex link on IGP phy.\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+
+ if (!link)
+ e_dbg("Link taking longer than expected.\n");
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+#endif
+
+#if 0
+/**
+ * e1000e_phy_force_speed_duplex_m88 - Force speed/duplex for m88 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Calls the PHY setup function to force speed and duplex. Clears the
+ * auto-crossover to force MDI manually. Resets the PHY to commit the
+ * changes. If time expires while waiting for link up, we reset the DSP.
+ * After reset, TX_CLK and CRS on Tx must be set. Return successful upon
+ * successful completion, else return corresponding error code.
+ **/
+s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+ /*
+ * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ * forced whenever speed and duplex are forced.
+ */
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+ ret_val = e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ goto out;
+
+ e_dbg("M88E1000 PSCR: %X\n", phy_data);
+
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
+
+ ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+ if (ret_val)
+ goto out;
+
+ /* Reset the phy to commit changes. */
+ ret_val = e1000e_commit_phy(hw);
+ if (ret_val)
+ goto out;
+
+ if (phy->autoneg_wait_to_complete) {
+ e_dbg("Waiting for forced speed/duplex link on M88 phy.\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
+ 100000, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link) {
+ /*
+ * We didn't get link.
+ * Reset the DSP and cross our fingers.
+ */
+ ret_val = e1e_wphy(hw,
+ M88E1000_PHY_PAGE_SELECT,
+ 0x001d);
+ if (ret_val)
+ goto out;
+ ret_val = e1000e_phy_reset_dsp(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
+ 100000, &link);
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1e_rphy(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Resetting the phy means we need to re-force TX_CLK in the
+ * Extended PHY Specific Control Register to 25MHz clock from
+ * the reset value of 2.5MHz.
+ */
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+ ret_val = e1e_wphy(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ goto out;
+
+ /*
+ * In addition, we must re-enable CRS on Tx for both half and full
+ * duplex.
+ */
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+ ret_val = e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+
+out:
+ return ret_val;
+}
+#endif
+
+#if 0
+/**
+ * e1000e_phy_force_speed_duplex_ife - Force PHY speed & duplex
+ * @hw: pointer to the HW structure
+ *
+ * Forces the speed and duplex settings of the PHY.
+ * This is a function pointer entry point only called by
+ * PHY setup routines.
+ **/
+s32 e1000e_phy_force_speed_duplex_ife(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+ if (phy->type != e1000_phy_ife) {
+ ret_val = e1000e_phy_force_speed_duplex_igp(hw);
+ goto out;
+ }
+
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &data);
+ if (ret_val)
+ goto out;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &data);
+
+ ret_val = e1e_wphy(hw, PHY_CONTROL, data);
+ if (ret_val)
+ goto out;
+
+ /* Disable MDI-X support for 10/100 */
+ ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~IFE_PMC_AUTO_MDIX;
+ data &= ~IFE_PMC_FORCE_MDIX;
+
+ ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, data);
+ if (ret_val)
+ goto out;
+
+ e_dbg("IFE PMC: %X\n", data);
+
+ udelay(1);
+
+ if (phy->autoneg_wait_to_complete) {
+ e_dbg("Waiting for forced speed/duplex link on IFE phy.\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+
+ if (!link)
+ e_dbg("Link taking longer than expected.\n");
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+#endif
+
+#if 0
+/**
+ * e1000e_phy_force_speed_duplex_setup - Configure forced PHY speed/duplex
+ * @hw: pointer to the HW structure
+ * @phy_ctrl: pointer to current value of PHY_CONTROL
+ *
+ * Forces speed and duplex on the PHY by doing the following: disable flow
+ * control, force speed/duplex on the MAC, disable auto speed detection,
+ * disable auto-negotiation, configure duplex, configure speed, configure
+ * the collision distance, write configuration to CTRL register. The
+ * caller must write to the PHY_CONTROL register for these settings to
+ * take affect.
+ **/
+void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 ctrl;
+
+ /* Turn off flow control when forcing speed/duplex */
+ hw->fc.current_mode = e1000_fc_none;
+
+ /* Force speed/duplex on the mac */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ctrl &= ~E1000_CTRL_SPD_SEL;
+
+ /* Disable Auto Speed Detection */
+ ctrl &= ~E1000_CTRL_ASDE;
+
+ /* Disable autoneg on the phy */
+ *phy_ctrl &= ~MII_CR_AUTO_NEG_EN;
+
+ /* Forcing Full or Half Duplex? */
+ if (mac->forced_speed_duplex & E1000_ALL_HALF_DUPLEX) {
+ ctrl &= ~E1000_CTRL_FD;
+ *phy_ctrl &= ~MII_CR_FULL_DUPLEX;
+ e_dbg("Half Duplex\n");
+ } else {
+ ctrl |= E1000_CTRL_FD;
+ *phy_ctrl |= MII_CR_FULL_DUPLEX;
+ e_dbg("Full Duplex\n");
+ }
+
+ /* Forcing 10mb or 100mb? */
+ if (mac->forced_speed_duplex & E1000_ALL_100_SPEED) {
+ ctrl |= E1000_CTRL_SPD_100;
+ *phy_ctrl |= MII_CR_SPEED_100;
+ *phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
+ e_dbg("Forcing 100mb\n");
+ } else {
+ ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
+ *phy_ctrl |= MII_CR_SPEED_10;
+ *phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
+ e_dbg("Forcing 10mb\n");
+ }
+
+ e1000e_config_collision_dist(hw);
+
+ ew32(CTRL, ctrl);
+}
+#endif
+
+/**
+ * e1000e_set_d3_lplu_state - Sets low power link up state for D3
+ * @hw: pointer to the HW structure
+ * @active: boolean used to enable/disable lplu
+ *
+ * Success returns 0, Failure returns 1
+ *
+ * The low power link up (lplu) state is set to the power management level D3
+ * and SmartSpeed is disabled when active is true, else clear lplu for D3
+ * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU
+ * is used during Dx states where the power conservation is most important.
+ * During driver activity, SmartSpeed should be enabled so performance is
+ * maintained.
+ **/
+s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+ u16 data;
+
+ if (!(hw->phy.ops.read_reg))
+ goto out;
+
+ ret_val = e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &data);
+ if (ret_val)
+ goto out;
+
+ if (!active) {
+ data &= ~IGP02E1000_PM_D3_LPLU;
+ ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT,
+ data);
+ if (ret_val)
+ goto out;
+ /*
+ * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1e_rphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ goto out;
+ } else if (phy->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1e_rphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ goto out;
+ }
+ } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) ||
+ (phy->autoneg_advertised == E1000_ALL_NOT_GIG) ||
+ (phy->autoneg_advertised == E1000_ALL_10_SPEED)) {
+ data |= IGP02E1000_PM_D3_LPLU;
+ ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT,
+ data);
+ if (ret_val)
+ goto out;
+
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_check_downshift - Checks whether a downshift in speed occurred
+ * @hw: pointer to the HW structure
+ *
+ * Success returns 0, Failure returns 1
+ *
+ * A downshift is detected by querying the PHY link health.
+ **/
+s32 e1000e_check_downshift(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, offset, mask;
+
+ switch (phy->type) {
+ case e1000_phy_m88:
+ case e1000_phy_gg82563:
+ case e1000_phy_bm:
+ case e1000_phy_82578:
+ offset = M88E1000_PHY_SPEC_STATUS;
+ mask = M88E1000_PSSR_DOWNSHIFT;
+ break;
+ case e1000_phy_igp_2:
+ case e1000_phy_igp:
+ case e1000_phy_igp_3:
+ offset = IGP01E1000_PHY_LINK_HEALTH;
+ mask = IGP01E1000_PLHR_SS_DOWNGRADE;
+ break;
+ default:
+ /* speed downshift not supported */
+ phy->speed_downgraded = false;
+ ret_val = E1000_SUCCESS;
+ goto out;
+ }
+
+ ret_val = e1e_rphy(hw, offset, &phy_data);
+
+ if (!ret_val)
+ phy->speed_downgraded = (phy_data & mask) ? true : false;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_check_polarity_m88 - Checks the polarity.
+ * @hw: pointer to the HW structure
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ *
+ * Polarity is determined based on the PHY specific status register.
+ **/
+s32 e1000e_check_polarity_m88(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_STATUS, &data);
+
+ if (!ret_val)
+ phy->cable_polarity = (data & M88E1000_PSSR_REV_POLARITY)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+
+ return ret_val;
+}
+
+/**
+ * e1000e_check_polarity_igp - Checks the polarity.
+ * @hw: pointer to the HW structure
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ *
+ * Polarity is determined based on the PHY port status register, and the
+ * current speed (since there is no polarity at 100Mbps).
+ **/
+s32 e1000e_check_polarity_igp(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data, offset, mask;
+
+ /*
+ * Polarity is determined based on the speed of
+ * our connection.
+ */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_STATUS, &data);
+ if (ret_val)
+ goto out;
+
+ if ((data & IGP01E1000_PSSR_SPEED_MASK) ==
+ IGP01E1000_PSSR_SPEED_1000MBPS) {
+ offset = IGP01E1000_PHY_PCS_INIT_REG;
+ mask = IGP01E1000_PHY_POLARITY_MASK;
+ } else {
+ /*
+ * This really only applies to 10Mbps since
+ * there is no polarity for 100Mbps (always 0).
+ */
+ offset = IGP01E1000_PHY_PORT_STATUS;
+ mask = IGP01E1000_PSSR_POLARITY_REVERSED;
+ }
+
+ ret_val = e1e_rphy(hw, offset, &data);
+
+ if (!ret_val)
+ phy->cable_polarity = (data & mask)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_check_polarity_ife - Check cable polarity for IFE PHY
+ * @hw: pointer to the HW structure
+ *
+ * Polarity is determined on the polarity reversal feature being enabled.
+ **/
+s32 e1000e_check_polarity_ife(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, offset, mask;
+
+ /*
+ * Polarity is determined based on the reversal feature being enabled.
+ */
+ if (phy->polarity_correction) {
+ offset = IFE_PHY_EXTENDED_STATUS_CONTROL;
+ mask = IFE_PESC_POLARITY_REVERSED;
+ } else {
+ offset = IFE_PHY_SPECIAL_CONTROL;
+ mask = IFE_PSC_FORCE_POLARITY;
+ }
+
+ ret_val = e1e_rphy(hw, offset, &phy_data);
+
+ if (!ret_val)
+ phy->cable_polarity = (phy_data & mask)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+
+ return ret_val;
+}
+
+/**
+ * e1000e_wait_autoneg - Wait for auto-neg completion
+ * @hw: pointer to the HW structure
+ *
+ * Waits for auto-negotiation to complete or for the auto-negotiation time
+ * limit to expire, which ever happens first.
+ **/
+s32 e1000e_wait_autoneg(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 i, phy_status;
+
+ if (!(hw->phy.ops.read_reg))
+ return E1000_SUCCESS;
+
+ /* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */
+ for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) {
+ ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ if (ret_val)
+ break;
+ ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ if (ret_val)
+ break;
+ if (phy_status & MII_SR_AUTONEG_COMPLETE)
+ break;
+ msleep(100);
+ }
+
+ /*
+ * PHY_AUTO_NEG_TIME expiration doesn't guarantee auto-negotiation
+ * has completed.
+ */
+ return ret_val;
+}
+
+/**
+ * e1000e_phy_has_link_generic - Polls PHY for link
+ * @hw: pointer to the HW structure
+ * @iterations: number of times to poll for link
+ * @usec_interval: delay between polling attempts
+ * @success: pointer to whether polling was successful or not
+ *
+ * Polls the PHY status register for link, 'iterations' number of times.
+ **/
+s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
+ u32 usec_interval, bool *success)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 i, phy_status;
+
+ if (!(hw->phy.ops.read_reg))
+ return E1000_SUCCESS;
+
+ for (i = 0; i < iterations; i++) {
+ /*
+ * Some PHYs require the PHY_STATUS register to be read
+ * twice due to the link bit being sticky. No harm doing
+ * it across the board.
+ */
+ ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ if (ret_val) {
+ /*
+ * If the first read fails, another entity may have
+ * ownership of the resources, wait and try again to
+ * see if they have relinquished the resources yet.
+ */
+ udelay(usec_interval);
+ }
+ ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ if (ret_val)
+ break;
+ if (phy_status & MII_SR_LINK_STATUS)
+ break;
+ if (usec_interval >= 1000)
+ mdelay(usec_interval/1000);
+ else
+ udelay(usec_interval);
+ }
+
+ *success = (i < iterations) ? true : false;
+
+ return ret_val;
+}
+
+#if 0
+/**
+ * e1000e_get_cable_length_m88 - Determine cable length for m88 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Reads the PHY specific status register to retrieve the cable length
+ * information. The cable length is determined by averaging the minimum and
+ * maximum values to get the "average" cable length. The m88 PHY has four
+ * possible cable length values, which are:
+ * Register Value Cable Length
+ * 0 < 50 meters
+ * 1 50 - 80 meters
+ * 2 80 - 110 meters
+ * 3 110 - 140 meters
+ * 4 > 140 meters
+ **/
+s32 e1000e_get_cable_length_m88(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, index;
+
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if (ret_val)
+ goto out;
+
+ index = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
+ M88E1000_PSSR_CABLE_LENGTH_SHIFT;
+ if (index >= M88E1000_CABLE_LENGTH_TABLE_SIZE - 1) {
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+
+ phy->min_cable_length = e1000_m88_cable_length_table[index];
+ phy->max_cable_length = e1000_m88_cable_length_table[index + 1];
+
+ phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2;
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_get_cable_length_igp_2 - Determine cable length for igp2 PHY
+ * @hw: pointer to the HW structure
+ *
+ * The automatic gain control (agc) normalizes the amplitude of the
+ * received signal, adjusting for the attenuation produced by the
+ * cable. By reading the AGC registers, which represent the
+ * combination of coarse and fine gain value, the value can be put
+ * into a lookup table to obtain the approximate cable length
+ * for each channel.
+ **/
+s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+ u16 phy_data, i, agc_value = 0;
+ u16 cur_agc_index, max_agc_index = 0;
+ u16 min_agc_index = IGP02E1000_CABLE_LENGTH_TABLE_SIZE - 1;
+ u16 agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] =
+ {IGP02E1000_PHY_AGC_A,
+ IGP02E1000_PHY_AGC_B,
+ IGP02E1000_PHY_AGC_C,
+ IGP02E1000_PHY_AGC_D};
+
+ /* Read the AGC registers for all channels */
+ for (i = 0; i < IGP02E1000_PHY_CHANNEL_NUM; i++) {
+ ret_val = e1e_rphy(hw, agc_reg_array[i], &phy_data);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Getting bits 15:9, which represent the combination of
+ * coarse and fine gain values. The result is a number
+ * that can be put into the lookup table to obtain the
+ * approximate cable length.
+ */
+ cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) &
+ IGP02E1000_AGC_LENGTH_MASK;
+
+ /* Array index bound check. */
+ if ((cur_agc_index >= IGP02E1000_CABLE_LENGTH_TABLE_SIZE) ||
+ (cur_agc_index == 0)) {
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+
+ /* Remove min & max AGC values from calculation. */
+ if (e1000_igp_2_cable_length_table[min_agc_index] >
+ e1000_igp_2_cable_length_table[cur_agc_index])
+ min_agc_index = cur_agc_index;
+ if (e1000_igp_2_cable_length_table[max_agc_index] <
+ e1000_igp_2_cable_length_table[cur_agc_index])
+ max_agc_index = cur_agc_index;
+
+ agc_value += e1000_igp_2_cable_length_table[cur_agc_index];
+ }
+
+ agc_value -= (e1000_igp_2_cable_length_table[min_agc_index] +
+ e1000_igp_2_cable_length_table[max_agc_index]);
+ agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2);
+
+ /* Calculate cable length with the error range of +/- 10 meters. */
+ phy->min_cable_length = ((agc_value - IGP02E1000_AGC_RANGE) > 0) ?
+ (agc_value - IGP02E1000_AGC_RANGE) : 0;
+ phy->max_cable_length = agc_value + IGP02E1000_AGC_RANGE;
+
+ phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2;
+
+out:
+ return ret_val;
+}
+#endif
+
+/**
+ * e1000e_get_phy_info_m88 - Retrieve PHY information
+ * @hw: pointer to the HW structure
+ *
+ * Valid for only copper links. Read the PHY status register (sticky read)
+ * to verify that link is up. Read the PHY special control register to
+ * determine the polarity and 10base-T extended distance. Read the PHY
+ * special status register to determine MDI/MDIx and current speed. If
+ * speed is 1000, then determine cable length, local and remote receiver.
+ **/
+s32 e1000e_get_phy_info_m88(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+ if (phy->media_type != e1000_media_type_copper) {
+ e_dbg("Phy info is only valid for copper media\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link) {
+ e_dbg("Phy info is only valid if link is up\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy->polarity_correction = (phy_data & M88E1000_PSCR_POLARITY_REVERSAL)
+ ? true : false;
+
+ ret_val = e1000e_check_polarity_m88(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy->is_mdix = (phy_data & M88E1000_PSSR_MDIX) ? true : false;
+
+ if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) {
+#if 0
+ ret_val = e1000e_get_cable_length(hw);
+#endif
+ ret_val = -E1000_ERR_CONFIG;
+ if (ret_val)
+ goto out;
+#if 0
+ ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+
+ phy->remote_rx = (phy_data & SR_1000T_REMOTE_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+#endif
+ } else {
+ /* Set values to "undefined" */
+ phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+ phy->local_rx = e1000_1000t_rx_status_undefined;
+ phy->remote_rx = e1000_1000t_rx_status_undefined;
+ }
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_get_phy_info_igp - Retrieve igp PHY information
+ * @hw: pointer to the HW structure
+ *
+ * Read PHY status to determine if link is up. If link is up, then
+ * set/determine 10base-T extended distance and polarity correction. Read
+ * PHY port status to determine MDI/MDIx and speed. Based on the speed,
+ * determine on the cable length, local and remote receiver.
+ **/
+s32 e1000e_get_phy_info_igp(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link) {
+ e_dbg("Phy info is only valid if link is up\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ phy->polarity_correction = true;
+
+ ret_val = e1000e_check_polarity_igp(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_STATUS, &data);
+ if (ret_val)
+ goto out;
+
+ phy->is_mdix = (data & IGP01E1000_PSSR_MDIX) ? true : false;
+
+ if ((data & IGP01E1000_PSSR_SPEED_MASK) ==
+ IGP01E1000_PSSR_SPEED_1000MBPS) {
+#if 0
+ ret_val = phy->ops.get_cable_length(hw);
+#endif
+ ret_val = -E1000_ERR_CONFIG;
+ if (ret_val)
+ goto out;
+#if 0
+ ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &data);
+ if (ret_val)
+ goto out;
+
+ phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+
+ phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+#endif
+ } else {
+ phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+ phy->local_rx = e1000_1000t_rx_status_undefined;
+ phy->remote_rx = e1000_1000t_rx_status_undefined;
+ }
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_phy_sw_reset - PHY software reset
+ * @hw: pointer to the HW structure
+ *
+ * Does a software reset of the PHY by reading the PHY control register and
+ * setting/write the control register reset bit to the PHY.
+ **/
+s32 e1000e_phy_sw_reset(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 phy_ctrl;
+
+ if (!(hw->phy.ops.read_reg))
+ goto out;
+
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_ctrl);
+ if (ret_val)
+ goto out;
+
+ phy_ctrl |= MII_CR_RESET;
+ ret_val = e1e_wphy(hw, PHY_CONTROL, phy_ctrl);
+ if (ret_val)
+ goto out;
+
+ udelay(1);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_phy_hw_reset_generic - PHY hardware reset
+ * @hw: pointer to the HW structure
+ *
+ * Verify the reset block is not blocking us from resetting. Acquire
+ * semaphore (if necessary) and read/set/write the device control reset
+ * bit in the PHY. Wait the appropriate delay time for the device to
+ * reset and release the semaphore (if necessary).
+ **/
+s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+ u32 ctrl;
+
+ ret_val = e1000e_check_reset_block(hw);
+ if (ret_val) {
+ ret_val = E1000_SUCCESS;
+ goto out;
+ }
+
+ ret_val = phy->ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ ctrl = er32(CTRL);
+ ew32(CTRL, ctrl | E1000_CTRL_PHY_RST);
+ e1e_flush();
+
+ udelay(phy->reset_delay_us);
+
+ ew32(CTRL, ctrl);
+ e1e_flush();
+
+ udelay(150);
+
+ phy->ops.release(hw);
+
+ ret_val = phy->ops.get_cfg_done(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_get_cfg_done - Generic configuration done
+ * @hw: pointer to the HW structure
+ *
+ * Generic function to wait 10 milli-seconds for configuration to complete
+ * and return success.
+ **/
+s32 e1000e_get_cfg_done(struct e1000_hw *hw __unused)
+{
+ mdelay(10);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_phy_init_script_igp3 - Inits the IGP3 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Initializes a Intel Gigabit PHY3 when an EEPROM is not present.
+ **/
+s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw)
+{
+ e_dbg("Running IGP 3 PHY init script\n");
+
+ /* PHY init IGP 3 */
+ /* Enable rise/fall, 10-mode work in class-A */
+ e1e_wphy(hw, 0x2F5B, 0x9018);
+ /* Remove all caps from Replica path filter */
+ e1e_wphy(hw, 0x2F52, 0x0000);
+ /* Bias trimming for ADC, AFE and Driver (Default) */
+ e1e_wphy(hw, 0x2FB1, 0x8B24);
+ /* Increase Hybrid poly bias */
+ e1e_wphy(hw, 0x2FB2, 0xF8F0);
+ /* Add 4% to Tx amplitude in Gig mode */
+ e1e_wphy(hw, 0x2010, 0x10B0);
+ /* Disable trimming (TTT) */
+ e1e_wphy(hw, 0x2011, 0x0000);
+ /* Poly DC correction to 94.6% + 2% for all channels */
+ e1e_wphy(hw, 0x20DD, 0x249A);
+ /* ABS DC correction to 95.9% */
+ e1e_wphy(hw, 0x20DE, 0x00D3);
+ /* BG temp curve trim */
+ e1e_wphy(hw, 0x28B4, 0x04CE);
+ /* Increasing ADC OPAMP stage 1 currents to max */
+ e1e_wphy(hw, 0x2F70, 0x29E4);
+ /* Force 1000 ( required for enabling PHY regs configuration) */
+ e1e_wphy(hw, 0x0000, 0x0140);
+ /* Set upd_freq to 6 */
+ e1e_wphy(hw, 0x1F30, 0x1606);
+ /* Disable NPDFE */
+ e1e_wphy(hw, 0x1F31, 0xB814);
+ /* Disable adaptive fixed FFE (Default) */
+ e1e_wphy(hw, 0x1F35, 0x002A);
+ /* Enable FFE hysteresis */
+ e1e_wphy(hw, 0x1F3E, 0x0067);
+ /* Fixed FFE for short cable lengths */
+ e1e_wphy(hw, 0x1F54, 0x0065);
+ /* Fixed FFE for medium cable lengths */
+ e1e_wphy(hw, 0x1F55, 0x002A);
+ /* Fixed FFE for long cable lengths */
+ e1e_wphy(hw, 0x1F56, 0x002A);
+ /* Enable Adaptive Clip Threshold */
+ e1e_wphy(hw, 0x1F72, 0x3FB0);
+ /* AHT reset limit to 1 */
+ e1e_wphy(hw, 0x1F76, 0xC0FF);
+ /* Set AHT master delay to 127 msec */
+ e1e_wphy(hw, 0x1F77, 0x1DEC);
+ /* Set scan bits for AHT */
+ e1e_wphy(hw, 0x1F78, 0xF9EF);
+ /* Set AHT Preset bits */
+ e1e_wphy(hw, 0x1F79, 0x0210);
+ /* Change integ_factor of channel A to 3 */
+ e1e_wphy(hw, 0x1895, 0x0003);
+ /* Change prop_factor of channels BCD to 8 */
+ e1e_wphy(hw, 0x1796, 0x0008);
+ /* Change cg_icount + enable integbp for channels BCD */
+ e1e_wphy(hw, 0x1798, 0xD008);
+ /*
+ * Change cg_icount + enable integbp + change prop_factor_master
+ * to 8 for channel A
+ */
+ e1e_wphy(hw, 0x1898, 0xD918);
+ /* Disable AHT in Slave mode on channel A */
+ e1e_wphy(hw, 0x187A, 0x0800);
+ /*
+ * Enable LPLU and disable AN to 1000 in non-D0a states,
+ * Enable SPD+B2B
+ */
+ e1e_wphy(hw, 0x0019, 0x008D);
+ /* Enable restart AN on an1000_dis change */
+ e1e_wphy(hw, 0x001B, 0x2080);
+ /* Enable wh_fifo read clock in 10/100 modes */
+ e1e_wphy(hw, 0x0014, 0x0045);
+ /* Restart AN, Speed selection is 1000 */
+ e1e_wphy(hw, 0x0000, 0x1340);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000e_get_phy_type_from_id - Get PHY type from id
+ * @phy_id: phy_id read from the phy
+ *
+ * Returns the phy type from the id.
+ **/
+enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id)
+{
+ enum e1000_phy_type phy_type = e1000_phy_unknown;
+
+ switch (phy_id) {
+ case M88E1000_I_PHY_ID:
+ case M88E1000_E_PHY_ID:
+ case M88E1111_I_PHY_ID:
+ case M88E1011_I_PHY_ID:
+ phy_type = e1000_phy_m88;
+ break;
+ case IGP01E1000_I_PHY_ID: /* IGP 1 & 2 share this */
+ phy_type = e1000_phy_igp_2;
+ break;
+ case GG82563_E_PHY_ID:
+ phy_type = e1000_phy_gg82563;
+ break;
+ case IGP03E1000_E_PHY_ID:
+ phy_type = e1000_phy_igp_3;
+ break;
+ case IFE_E_PHY_ID:
+ case IFE_PLUS_E_PHY_ID:
+ case IFE_C_E_PHY_ID:
+ phy_type = e1000_phy_ife;
+ break;
+ case BME1000_E_PHY_ID:
+ case BME1000_E_PHY_ID_R2:
+ phy_type = e1000_phy_bm;
+ break;
+ case I82578_E_PHY_ID:
+ phy_type = e1000_phy_82578;
+ break;
+ case I82577_E_PHY_ID:
+ phy_type = e1000_phy_82577;
+ break;
+ default:
+ phy_type = e1000_phy_unknown;
+ break;
+ }
+ return phy_type;
+}
+
+/**
+ * e1000e_determine_phy_address - Determines PHY address.
+ * @hw: pointer to the HW structure
+ *
+ * This uses a trial and error method to loop through possible PHY
+ * addresses. It tests each by reading the PHY ID registers and
+ * checking for a match.
+ **/
+s32 e1000e_determine_phy_address(struct e1000_hw *hw)
+{
+ s32 ret_val = -E1000_ERR_PHY_TYPE;
+ u32 phy_addr = 0;
+ u32 i;
+ enum e1000_phy_type phy_type = e1000_phy_unknown;
+
+ hw->phy.id = phy_type;
+
+ for (phy_addr = 0; phy_addr < E1000_MAX_PHY_ADDR; phy_addr++) {
+ hw->phy.addr = phy_addr;
+ i = 0;
+
+ do {
+ e1000e_get_phy_id(hw);
+ phy_type = e1000e_get_phy_type_from_id(hw->phy.id);
+
+ /*
+ * If phy_type is valid, break - we found our
+ * PHY address
+ */
+ if (phy_type != e1000_phy_unknown) {
+ ret_val = E1000_SUCCESS;
+ goto out;
+ }
+ msleep(1);
+ i++;
+ } while (i < 10);
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_get_phy_addr_for_bm_page - Retrieve PHY page address
+ * @page: page to access
+ *
+ * Returns the phy address for the page requested.
+ **/
+static u32 e1000e_get_phy_addr_for_bm_page(u32 page, u32 reg)
+{
+ u32 phy_addr = 2;
+
+ if ((page >= 768) || (page == 0 && reg == 25) || (reg == 31))
+ phy_addr = 1;
+
+ return phy_addr;
+}
+
+/**
+ * e1000e_write_phy_reg_bm - Write BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ s32 ret_val;
+ u32 page_select = 0;
+ u32 page = offset >> IGP_PAGE_SHIFT;
+ u32 page_shift = 0;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000e_access_phy_wakeup_reg_bm(hw, offset, &data,
+ false);
+ goto out;
+ }
+
+ hw->phy.addr = e1000e_get_phy_addr_for_bm_page(page, offset);
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ /*
+ * Page select is register 31 for phy address 1 and 22 for
+ * phy address 2 and 3. Page select is shifted only for
+ * phy address 1.
+ */
+ if (hw->phy.addr == 1) {
+ page_shift = IGP_PAGE_SHIFT;
+ page_select = IGP01E1000_PHY_PAGE_SELECT;
+ } else {
+ page_shift = 0;
+ page_select = BM_PHY_PAGE_SELECT;
+ }
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select,
+ (page << page_shift));
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+out:
+ hw->phy.ops.release(hw);
+ return ret_val;
+}
+
+/**
+ * e1000e_read_phy_reg_bm - Read BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting.
+ **/
+s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ s32 ret_val;
+ u32 page_select = 0;
+ u32 page = offset >> IGP_PAGE_SHIFT;
+ u32 page_shift = 0;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000e_access_phy_wakeup_reg_bm(hw, offset, data,
+ true);
+ goto out;
+ }
+
+ hw->phy.addr = e1000e_get_phy_addr_for_bm_page(page, offset);
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ /*
+ * Page select is register 31 for phy address 1 and 22 for
+ * phy address 2 and 3. Page select is shifted only for
+ * phy address 1.
+ */
+ if (hw->phy.addr == 1) {
+ page_shift = IGP_PAGE_SHIFT;
+ page_select = IGP01E1000_PHY_PAGE_SELECT;
+ } else {
+ page_shift = 0;
+ page_select = BM_PHY_PAGE_SELECT;
+ }
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select,
+ (page << page_shift));
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+out:
+ hw->phy.ops.release(hw);
+ return ret_val;
+}
+
+/**
+ * e1000e_read_phy_reg_bm2 - Read BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting.
+ **/
+s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ s32 ret_val;
+ u16 page = (u16)(offset >> IGP_PAGE_SHIFT);
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000e_access_phy_wakeup_reg_bm(hw, offset, data,
+ true);
+ goto out;
+ }
+
+ hw->phy.addr = 1;
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_PHY_PAGE_SELECT,
+ page);
+
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+out:
+ hw->phy.ops.release(hw);
+ return ret_val;
+}
+
+/**
+ * e1000e_write_phy_reg_bm2 - Write BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ s32 ret_val;
+ u16 page = (u16)(offset >> IGP_PAGE_SHIFT);
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000e_access_phy_wakeup_reg_bm(hw, offset, &data,
+ false);
+ goto out;
+ }
+
+ hw->phy.addr = 1;
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_PHY_PAGE_SELECT,
+ page);
+
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+out:
+ hw->phy.ops.release(hw);
+ return ret_val;
+}
+
+/**
+ * e1000e_access_phy_wakeup_reg_bm - Read BM PHY wakeup register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read or written
+ * @data: pointer to the data to read or write
+ * @read: determines if operation is read or write
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting. Note that procedure to read the wakeup
+ * registers are different. It works as such:
+ * 1) Set page 769, register 17, bit 2 = 1
+ * 2) Set page to 800 for host (801 if we were manageability)
+ * 3) Write the address using the address opcode (0x11)
+ * 4) Read or write the data using the data opcode (0x12)
+ * 5) Restore 769_17.2 to its original value
+ *
+ * Assumes semaphore already acquired.
+ **/
+static s32 e1000e_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read)
+{
+ s32 ret_val;
+ u16 reg = BM_PHY_REG_NUM(offset);
+ u16 phy_reg = 0;
+
+ /* Gig must be disabled for MDIO accesses to page 800 */
+ if ((hw->mac.type == e1000_pchlan) &&
+ (!(er32(PHY_CTRL) & E1000_PHY_CTRL_GBE_DISABLE)))
+ e_dbg("Attempting to access page 800 while gig enabled.\n");
+
+ /* All operations in this function are phy address 1 */
+ hw->phy.addr = 1;
+
+ /* Set page 769 */
+ e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, &phy_reg);
+ if (ret_val) {
+ e_dbg("Could not read PHY page 769\n");
+ goto out;
+ }
+
+ /* First clear bit 4 to avoid a power state change */
+ phy_reg &= ~(BM_WUC_HOST_WU_BIT);
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+ if (ret_val) {
+ e_dbg("Could not clear PHY page 769 bit 4\n");
+ goto out;
+ }
+
+ /* Write bit 2 = 1, and clear bit 4 to 769_17 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG,
+ phy_reg | BM_WUC_ENABLE_BIT);
+ if (ret_val) {
+ e_dbg("Could not write PHY page 769 bit 2\n");
+ goto out;
+ }
+
+ /* Select page 800 */
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_PAGE << IGP_PAGE_SHIFT));
+
+ /* Write the page 800 offset value using opcode 0x11 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ADDRESS_OPCODE, reg);
+ if (ret_val) {
+ e_dbg("Could not write address opcode to page 800\n");
+ goto out;
+ }
+
+ if (read) {
+ /* Read the page 800 value using opcode 0x12 */
+ ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE,
+ data);
+ } else {
+ /* Write the page 800 value using opcode 0x12 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE,
+ *data);
+ }
+
+ if (ret_val) {
+ e_dbg("Could not access data value from page 800\n");
+ goto out;
+ }
+
+ /*
+ * Restore 769_17.2 to its original value
+ * Set page 769
+ */
+ e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
+
+ /* Clear 769_17.2 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+ if (ret_val) {
+ e_dbg("Could not clear PHY page 769 bit 2\n");
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_power_up_phy_copper - Restore copper link in case of PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, restore the link to previous
+ * settings.
+ **/
+void e1000e_power_up_phy_copper(struct e1000_hw *hw)
+{
+ u16 mii_reg = 0;
+
+ /* The PHY will retain its settings across a power down/up cycle */
+ e1e_rphy(hw, PHY_CONTROL, &mii_reg);
+ mii_reg &= ~MII_CR_POWER_DOWN;
+ e1e_wphy(hw, PHY_CONTROL, mii_reg);
+}
+
+/**
+ * e1000e_power_down_phy_copper - Restore copper link in case of PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, restore the link to previous
+ * settings.
+ **/
+void e1000e_power_down_phy_copper(struct e1000_hw *hw)
+{
+ u16 mii_reg = 0;
+
+ /* The PHY will retain its settings across a power down/up cycle */
+ e1e_rphy(hw, PHY_CONTROL, &mii_reg);
+ mii_reg |= MII_CR_POWER_DOWN;
+ e1e_wphy(hw, PHY_CONTROL, mii_reg);
+ msleep(1);
+}
+
+/**
+ * e1000e_set_mdio_slow_mode_hv - Set slow MDIO access mode
+ * @hw: pointer to the HW structure
+ * @slow: true for slow mode, false for normal mode
+ *
+ * Assumes semaphore already acquired.
+ **/
+s32 e1000e_set_mdio_slow_mode_hv(struct e1000_hw *hw, bool slow)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 data = 0;
+
+ /* Set MDIO mode - page 769, register 16: 0x2580==slow, 0x2180==fast */
+ hw->phy.addr = 1;
+ ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_PORT_CTRL_PAGE << IGP_PAGE_SHIFT));
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_CS_CTRL1,
+ (0x2180 | (slow << 10)));
+ if (ret_val)
+ goto out;
+
+ /* dummy read when reverting to fast mode - throw away result */
+ if (!slow)
+ ret_val = e1000e_read_phy_reg_mdic(hw, BM_CS_CTRL1, &data);
+
+out:
+ return ret_val;
+}
+
+/**
+ * __e1000e_read_phy_reg_hv - Read HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ * @locked: semaphore has already been acquired or not
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and stores the retrieved information in data. Release any acquired
+ * semaphore before exiting.
+ **/
+static s32 __e1000e_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data,
+ bool locked)
+{
+ s32 ret_val;
+ u16 page = BM_PHY_REG_PAGE(offset);
+ u16 reg = BM_PHY_REG_NUM(offset);
+ bool in_slow_mode = false;
+
+ if (!locked) {
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Workaround failure in MDIO access while cable is disconnected */
+ if ((hw->phy.type == e1000_phy_82577) &&
+ !(er32(STATUS) & E1000_STATUS_LU)) {
+ ret_val = e1000e_set_mdio_slow_mode_hv(hw, true);
+ if (ret_val)
+ goto out;
+
+ in_slow_mode = true;
+ }
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000e_access_phy_wakeup_reg_bm(hw, offset,
+ data, true);
+ goto out;
+ }
+
+ if (page > 0 && page < HV_INTC_FC_PAGE_START) {
+ ret_val = e1000e_access_phy_debug_regs_hv(hw, offset,
+ data, true);
+ goto out;
+ }
+
+ hw->phy.addr = e1000e_get_phy_addr_for_hv_page(page);
+
+ if (page == HV_INTC_FC_PAGE_START)
+ page = 0;
+
+ if (reg > MAX_PHY_MULTI_PAGE_REG) {
+ u32 phy_addr = hw->phy.addr;
+
+ hw->phy.addr = 1;
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (page << IGP_PAGE_SHIFT));
+ hw->phy.addr = phy_addr;
+
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
+ data);
+out:
+ /* Revert to MDIO fast mode, if applicable */
+ if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
+ ret_val |= e1000e_set_mdio_slow_mode_hv(hw, false);
+
+ if (!locked)
+ hw->phy.ops.release(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_read_phy_reg_hv - Read HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore then reads the PHY register at offset and stores
+ * the retrieved information in data. Release the acquired semaphore
+ * before exiting.
+ **/
+s32 e1000e_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000e_read_phy_reg_hv(hw, offset, data, false);
+}
+
+/**
+ * e1000e_read_phy_reg_hv_locked - Read HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the PHY register at offset and stores the retrieved information
+ * in data. Assumes semaphore already acquired.
+ **/
+s32 e1000e_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000e_read_phy_reg_hv(hw, offset, data, true);
+}
+
+/**
+ * __e1000e_write_phy_reg_hv - Write HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ * @locked: semaphore has already been acquired or not
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+static s32 __e1000e_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data,
+ bool locked)
+{
+ s32 ret_val;
+ u16 page = BM_PHY_REG_PAGE(offset);
+ u16 reg = BM_PHY_REG_NUM(offset);
+ bool in_slow_mode = false;
+
+ if (!locked) {
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Workaround failure in MDIO access while cable is disconnected */
+ if ((hw->phy.type == e1000_phy_82577) &&
+ !(er32(STATUS) & E1000_STATUS_LU)) {
+ ret_val = e1000e_set_mdio_slow_mode_hv(hw, true);
+ if (ret_val)
+ goto out;
+
+ in_slow_mode = true;
+ }
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000e_access_phy_wakeup_reg_bm(hw, offset,
+ &data, false);
+ goto out;
+ }
+
+ if (page > 0 && page < HV_INTC_FC_PAGE_START) {
+ ret_val = e1000e_access_phy_debug_regs_hv(hw, offset,
+ &data, false);
+ goto out;
+ }
+
+ hw->phy.addr = e1000e_get_phy_addr_for_hv_page(page);
+
+ if (page == HV_INTC_FC_PAGE_START)
+ page = 0;
+
+ /*
+ * Workaround MDIO accesses being disabled after entering IEEE Power
+ * Down (whenever bit 11 of the PHY Control register is set)
+ */
+ if ((hw->phy.type == e1000_phy_82578) &&
+ (hw->phy.revision >= 1) &&
+ (hw->phy.addr == 2) &&
+ ((MAX_PHY_REG_ADDRESS & reg) == 0) &&
+ (data & (1 << 11))) {
+ u16 data2 = 0x7EFF;
+ ret_val = e1000e_access_phy_debug_regs_hv(hw, (1 << 6) | 0x3,
+ &data2, false);
+ if (ret_val)
+ goto out;
+ }
+
+ if (reg > MAX_PHY_MULTI_PAGE_REG) {
+ u32 phy_addr = hw->phy.addr;
+
+ hw->phy.addr = 1;
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (page << IGP_PAGE_SHIFT));
+ hw->phy.addr = phy_addr;
+
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
+ data);
+
+out:
+ /* Revert to MDIO fast mode, if applicable */
+ if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
+ ret_val |= e1000e_set_mdio_slow_mode_hv(hw, false);
+
+ if (!locked)
+ hw->phy.ops.release(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_write_phy_reg_hv - Write HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore then writes the data to PHY register at the offset.
+ * Release the acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000e_write_phy_reg_hv(hw, offset, data, false);
+}
+
+/**
+ * e1000e_write_phy_reg_hv_locked - Write HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Writes the data to PHY register at the offset. Assumes semaphore
+ * already acquired.
+ **/
+s32 e1000e_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000e_write_phy_reg_hv(hw, offset, data, true);
+}
+
+/**
+ * e1000e_get_phy_addr_for_hv_page - Get PHY adrress based on page
+ * @page: page to be accessed
+ **/
+static u32 e1000e_get_phy_addr_for_hv_page(u32 page)
+{
+ u32 phy_addr = 2;
+
+ if (page >= HV_INTC_FC_PAGE_START)
+ phy_addr = 1;
+
+ return phy_addr;
+}
+
+/**
+ * e1000e_access_phy_debug_regs_hv - Read HV PHY vendor specific high registers
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read or written
+ * @data: pointer to the data to be read or written
+ * @read: determines if operation is read or written
+ *
+ * Reads the PHY register at offset and stores the retreived information
+ * in data. Assumes semaphore already acquired. Note that the procedure
+ * to read these regs uses the address port and data port to read/write.
+ **/
+static s32 e1000e_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read)
+{
+ s32 ret_val;
+ u32 addr_reg = 0;
+ u32 data_reg = 0;
+
+ /* This takes care of the difference with desktop vs mobile phy */
+ addr_reg = (hw->phy.type == e1000_phy_82578) ?
+ I82578_ADDR_REG : I82577_ADDR_REG;
+ data_reg = addr_reg + 1;
+
+ /* All operations in this function are phy address 2 */
+ hw->phy.addr = 2;
+
+ /* masking with 0x3F to remove the page from offset */
+ ret_val = e1000e_write_phy_reg_mdic(hw, addr_reg, (u16)offset & 0x3F);
+ if (ret_val) {
+ e_dbg("Could not write PHY the HV address register\n");
+ goto out;
+ }
+
+ /* Read or write the data value next */
+ if (read)
+ ret_val = e1000e_read_phy_reg_mdic(hw, data_reg, data);
+ else
+ ret_val = e1000e_write_phy_reg_mdic(hw, data_reg, *data);
+
+ if (ret_val) {
+ e_dbg("Could not read data value from HV data register\n");
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_link_stall_workaround_hv - Si workaround
+ * @hw: pointer to the HW structure
+ *
+ * This function works around a Si bug where the link partner can get
+ * a link up indication before the PHY does. If small packets are sent
+ * by the link partner they can be placed in the packet buffer without
+ * being properly accounted for by the PHY and will stall preventing
+ * further packets from being received. The workaround is to clear the
+ * packet buffer after the PHY detects link up.
+ **/
+s32 e1000e_link_stall_workaround_hv(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u16 data;
+
+ if (hw->phy.type != e1000_phy_82578)
+ goto out;
+
+ /* Do not apply workaround if in PHY loopback bit 14 set */
+ e1e_rphy(hw, PHY_CONTROL, &data);
+ if (data & PHY_CONTROL_LB)
+ goto out;
+
+ /* check if link is up and at 1Gbps */
+ ret_val = e1e_rphy(hw, BM_CS_STATUS, &data);
+ if (ret_val)
+ goto out;
+
+ data &= BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_MASK;
+
+ if (data != (BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_1000))
+ goto out;
+
+ msleep(200);
+
+ /* flush the packets in the fifo buffer */
+ ret_val = e1e_wphy(hw, HV_MUX_DATA_CTRL,
+ HV_MUX_DATA_CTRL_GEN_TO_MAC |
+ HV_MUX_DATA_CTRL_FORCE_SPEED);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1e_wphy(hw, HV_MUX_DATA_CTRL,
+ HV_MUX_DATA_CTRL_GEN_TO_MAC);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_check_polarity_82577 - Checks the polarity.
+ * @hw: pointer to the HW structure
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ *
+ * Polarity is determined based on the PHY specific status register.
+ **/
+s32 e1000e_check_polarity_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+
+ ret_val = e1e_rphy(hw, I82577_PHY_STATUS_2, &data);
+
+ if (!ret_val)
+ phy->cable_polarity = (data & I82577_PHY_STATUS2_REV_POLARITY)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+
+ return ret_val;
+}
+
+#if 0
+/**
+ * e1000e_phy_force_speed_duplex_82577 - Force speed/duplex for I82577 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Calls the PHY setup function to force speed and duplex. Clears the
+ * auto-crossover to force MDI manually. Waits for link and returns
+ * successful if link up is successful, else -E1000_ERR_PHY (-2).
+ **/
+s32 e1000e_phy_force_speed_duplex_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
+
+ ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Clear Auto-Crossover to force MDI manually. 82577 requires MDI
+ * forced whenever speed and duplex are forced.
+ */
+ ret_val = e1e_rphy(hw, I82577_PHY_CTRL_2, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data &= ~I82577_PHY_CTRL2_AUTO_MDIX;
+ phy_data &= ~I82577_PHY_CTRL2_FORCE_MDI_MDIX;
+
+ ret_val = e1e_wphy(hw, I82577_PHY_CTRL_2, phy_data);
+ if (ret_val)
+ goto out;
+
+ e_dbg("I82577_PHY_CTRL_2: %X\n", phy_data);
+
+ udelay(1);
+
+ if (phy->autoneg_wait_to_complete) {
+ e_dbg("Waiting for forced speed/duplex link on 82577 phy\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+
+ if (!link)
+ e_dbg("Link taking longer than expected.\n");
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+#endif
+
+/**
+ * e1000e_get_phy_info_82577 - Retrieve I82577 PHY information
+ * @hw: pointer to the HW structure
+ *
+ * Read PHY status to determine if link is up. If link is up, then
+ * set/determine 10base-T extended distance and polarity correction. Read
+ * PHY port status to determine MDI/MDIx and speed. Based on the speed,
+ * determine on the cable length, local and remote receiver.
+ **/
+s32 e1000e_get_phy_info_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link) {
+ e_dbg("Phy info is only valid if link is up\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ phy->polarity_correction = true;
+
+ ret_val = e1000e_check_polarity_82577(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1e_rphy(hw, I82577_PHY_STATUS_2, &data);
+ if (ret_val)
+ goto out;
+
+ phy->is_mdix = (data & I82577_PHY_STATUS2_MDIX) ? true : false;
+
+ if ((data & I82577_PHY_STATUS2_SPEED_MASK) ==
+ I82577_PHY_STATUS2_SPEED_1000MBPS) {
+#if 0
+ ret_val = e1000e_get_cable_length(hw);
+#endif
+ ret_val = -E1000_ERR_CONFIG;
+ if (ret_val)
+ goto out;
+#if 0
+ ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &data);
+ if (ret_val)
+ goto out;
+
+ phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+
+ phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+#endif
+ } else {
+ phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+ phy->local_rx = e1000_1000t_rx_status_undefined;
+ phy->remote_rx = e1000_1000t_rx_status_undefined;
+ }
+out:
+ return ret_val;
+}
+
+#if 0
+/**
+ * e1000e_get_cable_length_82577 - Determine cable length for 82577 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Reads the diagnostic status register and verifies result is valid before
+ * placing it in the phy_cable_length field.
+ **/
+s32 e1000e_get_cable_length_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, length;
+
+ ret_val = e1e_rphy(hw, I82577_PHY_DIAG_STATUS, &phy_data);
+ if (ret_val)
+ goto out;
+
+ length = (phy_data & I82577_DSTATUS_CABLE_LENGTH) >>
+ I82577_DSTATUS_CABLE_LENGTH_SHIFT;
+
+ if (length == E1000_CABLE_LENGTH_UNDEFINED)
+ ret_val = -E1000_ERR_PHY;
+
+ phy->cable_length = length;
+
+out:
+ return ret_val;
+}
+#endif
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#ifndef _E1000E_PHY_H_
+#define _E1000E_PHY_H_
+
+void e1000e_init_phy_ops_generic(struct e1000_hw *hw);
+s32 e1000e_check_downshift(struct e1000_hw *hw);
+s32 e1000e_check_polarity_m88(struct e1000_hw *hw);
+s32 e1000e_check_polarity_igp(struct e1000_hw *hw);
+s32 e1000e_check_polarity_ife(struct e1000_hw *hw);
+s32 e1000e_check_reset_block_generic(struct e1000_hw *hw);
+s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw);
+s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw);
+#if 0
+s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw);
+s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw);
+s32 e1000e_phy_force_speed_duplex_ife(struct e1000_hw *hw);
+#endif
+#if 0
+s32 e1000e_get_cable_length_m88(struct e1000_hw *hw);
+s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw);
+#endif
+s32 e1000e_get_cfg_done(struct e1000_hw *hw);
+s32 e1000e_get_phy_id(struct e1000_hw *hw);
+s32 e1000e_get_phy_info_igp(struct e1000_hw *hw);
+s32 e1000e_get_phy_info_m88(struct e1000_hw *hw);
+s32 e1000e_phy_sw_reset(struct e1000_hw *hw);
+#if 0
+void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl);
+#endif
+s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw);
+s32 e1000e_phy_reset_dsp(struct e1000_hw *hw);
+s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active);
+s32 e1000e_setup_copper_link(struct e1000_hw *hw);
+s32 e1000e_wait_autoneg(struct e1000_hw *hw);
+s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_phy_reset_dsp(struct e1000_hw *hw);
+s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
+ u32 usec_interval, bool *success);
+s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw);
+enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id);
+s32 e1000e_determine_phy_address(struct e1000_hw *hw);
+s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data);
+void e1000e_power_up_phy_copper(struct e1000_hw *hw);
+void e1000e_power_down_phy_copper(struct e1000_hw *hw);
+s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_set_mdio_slow_mode_hv(struct e1000_hw *hw, bool slow);
+s32 e1000e_link_stall_workaround_hv(struct e1000_hw *hw);
+s32 e1000e_copper_link_setup_82577(struct e1000_hw *hw);
+s32 e1000e_check_polarity_82577(struct e1000_hw *hw);
+s32 e1000e_get_phy_info_82577(struct e1000_hw *hw);
+#if 0
+s32 e1000e_phy_force_speed_duplex_82577(struct e1000_hw *hw);
+#endif
+#if 0
+s32 e1000e_get_cable_length_82577(struct e1000_hw *hw);
+#endif
+
+#define E1000_MAX_PHY_ADDR 4
+
+/* IGP01E1000 Specific Registers */
+#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* Port Config */
+#define IGP01E1000_PHY_PORT_STATUS 0x11 /* Status */
+#define IGP01E1000_PHY_PORT_CTRL 0x12 /* Control */
+#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health */
+#define IGP01E1000_GMII_FIFO 0x14 /* GMII FIFO */
+#define IGP01E1000_PHY_CHANNEL_QUALITY 0x15 /* PHY Channel Quality */
+#define IGP02E1000_PHY_POWER_MGMT 0x19 /* Power Management */
+#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* Page Select */
+#define BM_PHY_PAGE_SELECT 22 /* Page Select for BM */
+#define IGP_PAGE_SHIFT 5
+#define PHY_REG_MASK 0x1F
+
+/* BM/HV Specific Registers */
+#define BM_PORT_CTRL_PAGE 769
+#define BM_PCIE_PAGE 770
+#define BM_WUC_PAGE 800
+#define BM_WUC_ADDRESS_OPCODE 0x11
+#define BM_WUC_DATA_OPCODE 0x12
+#define BM_WUC_ENABLE_PAGE BM_PORT_CTRL_PAGE
+#define BM_WUC_ENABLE_REG 17
+#define BM_WUC_ENABLE_BIT (1 << 2)
+#define BM_WUC_HOST_WU_BIT (1 << 4)
+
+#define PHY_UPPER_SHIFT 21
+#define BM_PHY_REG(page, reg) \
+ (((reg) & MAX_PHY_REG_ADDRESS) |\
+ (((page) & 0xFFFF) << PHY_PAGE_SHIFT) |\
+ (((reg) & ~MAX_PHY_REG_ADDRESS) << (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)))
+#define BM_PHY_REG_PAGE(offset) \
+ ((u16)(((offset) >> PHY_PAGE_SHIFT) & 0xFFFF))
+#define BM_PHY_REG_NUM(offset) \
+ ((u16)(((offset) & MAX_PHY_REG_ADDRESS) |\
+ (((offset) >> (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)) &\
+ ~MAX_PHY_REG_ADDRESS)))
+
+#define HV_INTC_FC_PAGE_START 768
+#define I82578_ADDR_REG 29
+#define I82577_ADDR_REG 16
+#define I82577_CFG_REG 22
+#define I82577_CFG_ASSERT_CRS_ON_TX (1 << 15)
+#define I82577_CFG_ENABLE_DOWNSHIFT (3 << 10) /* auto downshift 100/10 */
+#define I82577_CTRL_REG 23
+
+/* 82577 specific PHY registers */
+#define I82577_PHY_CTRL_2 18
+#define I82577_PHY_LBK_CTRL 19
+#define I82577_PHY_STATUS_2 26
+#define I82577_PHY_DIAG_STATUS 31
+
+/* I82577 PHY Status 2 */
+#define I82577_PHY_STATUS2_REV_POLARITY 0x0400
+#define I82577_PHY_STATUS2_MDIX 0x0800
+#define I82577_PHY_STATUS2_SPEED_MASK 0x0300
+#define I82577_PHY_STATUS2_SPEED_1000MBPS 0x0200
+#define I82577_PHY_STATUS2_SPEED_100MBPS 0x0100
+
+/* I82577 PHY Control 2 */
+#define I82577_PHY_CTRL2_AUTO_MDIX 0x0400
+#define I82577_PHY_CTRL2_FORCE_MDI_MDIX 0x0200
+
+/* I82577 PHY Diagnostics Status */
+#define I82577_DSTATUS_CABLE_LENGTH 0x03FC
+#define I82577_DSTATUS_CABLE_LENGTH_SHIFT 2
+
+/* BM PHY Copper Specific Control 1 */
+#define BM_CS_CTRL1 16
+#define BM_CS_CTRL1_ENERGY_DETECT 0x0300 /* Enable Energy Detect */
+
+/* BM PHY Copper Specific Status */
+#define BM_CS_STATUS 17
+#define BM_CS_STATUS_ENERGY_DETECT 0x0010 /* Energy Detect Status */
+#define BM_CS_STATUS_LINK_UP 0x0400
+#define BM_CS_STATUS_RESOLVED 0x0800
+#define BM_CS_STATUS_SPEED_MASK 0xC000
+#define BM_CS_STATUS_SPEED_1000 0x8000
+
+/* 82577 Mobile Phy Status Register */
+#define HV_M_STATUS 26
+#define HV_M_STATUS_AUTONEG_COMPLETE 0x1000
+#define HV_M_STATUS_SPEED_MASK 0x0300
+#define HV_M_STATUS_SPEED_1000 0x0200
+#define HV_M_STATUS_LINK_UP 0x0040
+
+#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4
+#define IGP01E1000_PHY_POLARITY_MASK 0x0078
+
+#define IGP01E1000_PSCR_AUTO_MDIX 0x1000
+#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0=MDI, 1=MDIX */
+
+#define IGP01E1000_PSCFR_SMART_SPEED 0x0080
+
+/* Enable flexible speed on link-up */
+#define IGP01E1000_GMII_FLEX_SPD 0x0010
+#define IGP01E1000_GMII_SPD 0x0020 /* Enable SPD */
+
+#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */
+#define IGP02E1000_PM_D0_LPLU 0x0002 /* For D0a states */
+#define IGP02E1000_PM_D3_LPLU 0x0004 /* For all other states */
+
+#define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000
+
+#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002
+#define IGP01E1000_PSSR_MDIX 0x0800
+#define IGP01E1000_PSSR_SPEED_MASK 0xC000
+#define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000
+
+#define IGP02E1000_PHY_CHANNEL_NUM 4
+#define IGP02E1000_PHY_AGC_A 0x11B1
+#define IGP02E1000_PHY_AGC_B 0x12B1
+#define IGP02E1000_PHY_AGC_C 0x14B1
+#define IGP02E1000_PHY_AGC_D 0x18B1
+
+#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Course - 15:13, Fine - 12:9 */
+#define IGP02E1000_AGC_LENGTH_MASK 0x7F
+#define IGP02E1000_AGC_RANGE 15
+
+#define IGP03E1000_PHY_MISC_CTRL 0x1B
+#define IGP03E1000_PHY_MISC_DUPLEX_MANUAL_SET 0x1000 /* Manually Set Duplex */
+
+#define E1000_CABLE_LENGTH_UNDEFINED 0xFF
+
+#define E1000_KMRNCTRLSTA_OFFSET 0x001F0000
+#define E1000_KMRNCTRLSTA_OFFSET_SHIFT 16
+#define E1000_KMRNCTRLSTA_REN 0x00200000
+#define E1000_KMRNCTRLSTA_DIAG_OFFSET 0x3 /* Kumeran Diagnostic */
+#define E1000_KMRNCTRLSTA_TIMEOUTS 0x4 /* Kumeran Timeouts */
+#define E1000_KMRNCTRLSTA_INBAND_PARAM 0x9 /* Kumeran InBand Parameters */
+#define E1000_KMRNCTRLSTA_DIAG_NELPBK 0x1000 /* Nearend Loopback mode */
+#define E1000_KMRNCTRLSTA_K1_CONFIG 0x7
+#define E1000_KMRNCTRLSTA_K1_ENABLE 0x0002
+
+#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10
+#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY Special Control */
+#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY Special and LED Control */
+#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control */
+
+/* IFE PHY Extended Status Control */
+#define IFE_PESC_POLARITY_REVERSED 0x0100
+
+/* IFE PHY Special Control */
+#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010
+#define IFE_PSC_FORCE_POLARITY 0x0020
+#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100
+
+/* IFE PHY Special Control and LED Control */
+#define IFE_PSCL_PROBE_MODE 0x0020
+#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */
+#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */
+
+/* IFE PHY MDIX Control */
+#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */
+#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDI-X, 0=force MDI */
+#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable auto MDI/MDI-X, 0=disable */
+
+#endif
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+FILE_LICENCE ( GPL2_OR_LATER );
+
+#ifndef _E1000E_REGS_H_
+#define _E1000E_REGS_H_
+
+#define E1000_CTRL 0x00000 /* Device Control - RW */
+#define E1000_CTRL_DUP 0x00004 /* Device Control Duplicate (Shadow) - RW */
+#define E1000_STATUS 0x00008 /* Device Status - RO */
+#define E1000_EECD 0x00010 /* EEPROM/Flash Control - RW */
+#define E1000_EERD 0x00014 /* EEPROM Read - RW */
+#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */
+#define E1000_FLA 0x0001C /* Flash Access - RW */
+#define E1000_MDIC 0x00020 /* MDI Control - RW */
+#define E1000_SCTL 0x00024 /* SerDes Control - RW */
+#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */
+#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */
+#define E1000_FEXT 0x0002C /* Future Extended - RW */
+#define E1000_FEXTNVM 0x00028 /* Future Extended NVM - RW */
+#define E1000_FCT 0x00030 /* Flow Control Type - RW */
+#define E1000_CONNSW 0x00034 /* Copper/Fiber switch control - RW */
+#define E1000_VET 0x00038 /* VLAN Ether Type - RW */
+#define E1000_ICR 0x000C0 /* Interrupt Cause Read - R/clr */
+#define E1000_ITR 0x000C4 /* Interrupt Throttling Rate - RW */
+#define E1000_ICS 0x000C8 /* Interrupt Cause Set - WO */
+#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */
+#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */
+#define E1000_IAM 0x000E0 /* Interrupt Acknowledge Auto Mask */
+#define E1000_IVAR 0x000E4 /* Interrupt Vector Allocation Register - RW */
+#define E1000_SVCR 0x000F0
+#define E1000_SVT 0x000F4
+#define E1000_RCTL 0x00100 /* Rx Control - RW */
+#define E1000_FCTTV 0x00170 /* Flow Control Transmit Timer Value - RW */
+#define E1000_TXCW 0x00178 /* Tx Configuration Word - RW */
+#define E1000_RXCW 0x00180 /* Rx Configuration Word - RO */
+#define E1000_PBA_ECC 0x01100 /* PBA ECC Register */
+#define E1000_TCTL 0x00400 /* Tx Control - RW */
+#define E1000_TCTL_EXT 0x00404 /* Extended Tx Control - RW */
+#define E1000_TIPG 0x00410 /* Tx Inter-packet gap -RW */
+#define E1000_TBT 0x00448 /* Tx Burst Timer - RW */
+#define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */
+#define E1000_LEDCTL 0x00E00 /* LED Control - RW */
+#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */
+#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */
+#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */
+#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */
+#define E1000_PBS 0x01008 /* Packet Buffer Size */
+#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */
+#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */
+#define E1000_FLASHT 0x01028 /* FLASH Timer Register */
+#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */
+#define E1000_FLSWCTL 0x01030 /* FLASH control register */
+#define E1000_FLSWDATA 0x01034 /* FLASH data register */
+#define E1000_FLSWCNT 0x01038 /* FLASH Access Counter */
+#define E1000_FLOP 0x0103C /* FLASH Opcode Register */
+#define E1000_I2CCMD 0x01028 /* SFPI2C Command Register - RW */
+#define E1000_I2CPARAMS 0x0102C /* SFPI2C Parameters Register - RW */
+#define E1000_WDSTP 0x01040 /* Watchdog Setup - RW */
+#define E1000_SWDSTS 0x01044 /* SW Device Status - RW */
+#define E1000_FRTIMER 0x01048 /* Free Running Timer - RW */
+#define E1000_ERT 0x02008 /* Early Rx Threshold - RW */
+#define E1000_FCRTL 0x02160 /* Flow Control Receive Threshold Low - RW */
+#define E1000_FCRTH 0x02168 /* Flow Control Receive Threshold High - RW */
+#define E1000_PSRCTL 0x02170 /* Packet Split Receive Control - RW */
+#define E1000_RDFPCQ(_n) (0x02430 + (0x4 * (_n)))
+#define E1000_PBRTH 0x02458 /* PB Rx Arbitration Threshold - RW */
+#define E1000_FCRTV 0x02460 /* Flow Control Refresh Timer Value - RW */
+/* Split and Replication Rx Control - RW */
+#define E1000_RDPUMB 0x025CC /* DMA Rx Descriptor uC Mailbox - RW */
+#define E1000_RDPUAD 0x025D0 /* DMA Rx Descriptor uC Addr Command - RW */
+#define E1000_RDPUWD 0x025D4 /* DMA Rx Descriptor uC Data Write - RW */
+#define E1000_RDPURD 0x025D8 /* DMA Rx Descriptor uC Data Read - RW */
+#define E1000_RDPUCTL 0x025DC /* DMA Rx Descriptor uC Control - RW */
+#define E1000_RDTR 0x02820 /* Rx Delay Timer - RW */
+#define E1000_RADV 0x0282C /* Rx Interrupt Absolute Delay Timer - RW */
+/*
+ * Convenience macros
+ *
+ * Note: "_n" is the queue number of the register to be written to.
+ *
+ * Example usage:
+ * E1000_RDBAL_REG(current_rx_queue)
+ */
+#define E1000_RDBAL(_n) ((_n) < 4 ? (0x02800 + ((_n) * 0x100)) : \
+ (0x0C000 + ((_n) * 0x40)))
+#define E1000_RDBAH(_n) ((_n) < 4 ? (0x02804 + ((_n) * 0x100)) : \
+ (0x0C004 + ((_n) * 0x40)))
+#define E1000_RDLEN(_n) ((_n) < 4 ? (0x02808 + ((_n) * 0x100)) : \
+ (0x0C008 + ((_n) * 0x40)))
+#define E1000_SRRCTL(_n) ((_n) < 4 ? (0x0280C + ((_n) * 0x100)) : \
+ (0x0C00C + ((_n) * 0x40)))
+#define E1000_RDH(_n) ((_n) < 4 ? (0x02810 + ((_n) * 0x100)) : \
+ (0x0C010 + ((_n) * 0x40)))
+#define E1000_RXCTL(_n) ((_n) < 4 ? (0x02814 + ((_n) * 0x100)) : \
+ (0x0C014 + ((_n) * 0x40)))
+#define E1000_DCA_RXCTRL(_n) E1000_RXCTL(_n)
+#define E1000_RDT(_n) ((_n) < 4 ? (0x02818 + ((_n) * 0x100)) : \
+ (0x0C018 + ((_n) * 0x40)))
+#define E1000_RXDCTL(_n) ((_n) < 4 ? (0x02828 + ((_n) * 0x100)) : \
+ (0x0C028 + ((_n) * 0x40)))
+#define E1000_RQDPC(_n) ((_n) < 4 ? (0x02830 + ((_n) * 0x100)) : \
+ (0x0C030 + ((_n) * 0x40)))
+#define E1000_TDBAL(_n) ((_n) < 4 ? (0x03800 + ((_n) * 0x100)) : \
+ (0x0E000 + ((_n) * 0x40)))
+#define E1000_TDBAH(_n) ((_n) < 4 ? (0x03804 + ((_n) * 0x100)) : \
+ (0x0E004 + ((_n) * 0x40)))
+#define E1000_TDLEN(_n) ((_n) < 4 ? (0x03808 + ((_n) * 0x100)) : \
+ (0x0E008 + ((_n) * 0x40)))
+#define E1000_TDH(_n) ((_n) < 4 ? (0x03810 + ((_n) * 0x100)) : \
+ (0x0E010 + ((_n) * 0x40)))
+#define E1000_TXCTL(_n) ((_n) < 4 ? (0x03814 + ((_n) * 0x100)) : \
+ (0x0E014 + ((_n) * 0x40)))
+#define E1000_DCA_TXCTRL(_n) E1000_TXCTL(_n)
+#define E1000_TDT(_n) ((_n) < 4 ? (0x03818 + ((_n) * 0x100)) : \
+ (0x0E018 + ((_n) * 0x40)))
+#define E1000_TXDCTL(_n) ((_n) < 4 ? (0x03828 + ((_n) * 0x100)) : \
+ (0x0E028 + ((_n) * 0x40)))
+#define E1000_TDWBAL(_n) ((_n) < 4 ? (0x03838 + ((_n) * 0x100)) : \
+ (0x0E038 + ((_n) * 0x40)))
+#define E1000_TDWBAH(_n) ((_n) < 4 ? (0x0383C + ((_n) * 0x100)) : \
+ (0x0E03C + ((_n) * 0x40)))
+#define E1000_TARC(_n) (0x03840 + ((_n) * 0x100))
+#define E1000_RSRPD 0x02C00 /* Rx Small Packet Detect - RW */
+#define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */
+#define E1000_TXDMAC 0x03000 /* Tx DMA Control - RW */
+#define E1000_KABGTXD 0x03004 /* AFE Band Gap Transmit Ref Data */
+#define E1000_PSRTYPE(_i) (0x05480 + ((_i) * 4))
+#define E1000_RAL(_i) (((_i) <= 15) ? (0x05400 + ((_i) * 8)) : \
+ (0x054E0 + ((_i - 16) * 8)))
+#define E1000_RAH(_i) (((_i) <= 15) ? (0x05404 + ((_i) * 8)) : \
+ (0x054E4 + ((_i - 16) * 8)))
+#define E1000_IP4AT_REG(_i) (0x05840 + ((_i) * 8))
+#define E1000_IP6AT_REG(_i) (0x05880 + ((_i) * 4))
+#define E1000_WUPM_REG(_i) (0x05A00 + ((_i) * 4))
+#define E1000_FFMT_REG(_i) (0x09000 + ((_i) * 8))
+#define E1000_FFVT_REG(_i) (0x09800 + ((_i) * 8))
+#define E1000_FFLT_REG(_i) (0x05F00 + ((_i) * 8))
+#define E1000_TDFH 0x03410 /* Tx Data FIFO Head - RW */
+#define E1000_TDFT 0x03418 /* Tx Data FIFO Tail - RW */
+#define E1000_TDFHS 0x03420 /* Tx Data FIFO Head Saved - RW */
+#define E1000_TDFTS 0x03428 /* Tx Data FIFO Tail Saved - RW */
+#define E1000_TDFPC 0x03430 /* Tx Data FIFO Packet Count - RW */
+#define E1000_TDPUMB 0x0357C /* DMA Tx Descriptor uC Mail Box - RW */
+#define E1000_TDPUAD 0x03580 /* DMA Tx Descriptor uC Addr Command - RW */
+#define E1000_TDPUWD 0x03584 /* DMA Tx Descriptor uC Data Write - RW */
+#define E1000_TDPURD 0x03588 /* DMA Tx Descriptor uC Data Read - RW */
+#define E1000_TDPUCTL 0x0358C /* DMA Tx Descriptor uC Control - RW */
+#define E1000_DTXCTL 0x03590 /* DMA Tx Control - RW */
+#define E1000_TIDV 0x03820 /* Tx Interrupt Delay Value - RW */
+#define E1000_TADV 0x0382C /* Tx Interrupt Absolute Delay Val - RW */
+#define E1000_TSPMT 0x03830 /* TCP Segmentation PAD & Min Threshold - RW */
+#define E1000_CRCERRS 0x04000 /* CRC Error Count - R/clr */
+#define E1000_ALGNERRC 0x04004 /* Alignment Error Count - R/clr */
+#define E1000_SYMERRS 0x04008 /* Symbol Error Count - R/clr */
+#define E1000_RXERRC 0x0400C /* Receive Error Count - R/clr */
+#define E1000_MPC 0x04010 /* Missed Packet Count - R/clr */
+#define E1000_SCC 0x04014 /* Single Collision Count - R/clr */
+#define E1000_ECOL 0x04018 /* Excessive Collision Count - R/clr */
+#define E1000_MCC 0x0401C /* Multiple Collision Count - R/clr */
+#define E1000_LATECOL 0x04020 /* Late Collision Count - R/clr */
+#define E1000_COLC 0x04028 /* Collision Count - R/clr */
+#define E1000_DC 0x04030 /* Defer Count - R/clr */
+#define E1000_TNCRS 0x04034 /* Tx-No CRS - R/clr */
+#define E1000_SEC 0x04038 /* Sequence Error Count - R/clr */
+#define E1000_CEXTERR 0x0403C /* Carrier Extension Error Count - R/clr */
+#define E1000_RLEC 0x04040 /* Receive Length Error Count - R/clr */
+#define E1000_XONRXC 0x04048 /* XON Rx Count - R/clr */
+#define E1000_XONTXC 0x0404C /* XON Tx Count - R/clr */
+#define E1000_XOFFRXC 0x04050 /* XOFF Rx Count - R/clr */
+#define E1000_XOFFTXC 0x04054 /* XOFF Tx Count - R/clr */
+#define E1000_FCRUC 0x04058 /* Flow Control Rx Unsupported Count- R/clr */
+#define E1000_PRC64 0x0405C /* Packets Rx (64 bytes) - R/clr */
+#define E1000_PRC127 0x04060 /* Packets Rx (65-127 bytes) - R/clr */
+#define E1000_PRC255 0x04064 /* Packets Rx (128-255 bytes) - R/clr */
+#define E1000_PRC511 0x04068 /* Packets Rx (255-511 bytes) - R/clr */
+#define E1000_PRC1023 0x0406C /* Packets Rx (512-1023 bytes) - R/clr */
+#define E1000_PRC1522 0x04070 /* Packets Rx (1024-1522 bytes) - R/clr */
+#define E1000_GPRC 0x04074 /* Good Packets Rx Count - R/clr */
+#define E1000_BPRC 0x04078 /* Broadcast Packets Rx Count - R/clr */
+#define E1000_MPRC 0x0407C /* Multicast Packets Rx Count - R/clr */
+#define E1000_GPTC 0x04080 /* Good Packets Tx Count - R/clr */
+#define E1000_GORCL 0x04088 /* Good Octets Rx Count Low - R/clr */
+#define E1000_GORCH 0x0408C /* Good Octets Rx Count High - R/clr */
+#define E1000_GOTCL 0x04090 /* Good Octets Tx Count Low - R/clr */
+#define E1000_GOTCH 0x04094 /* Good Octets Tx Count High - R/clr */
+#define E1000_RNBC 0x040A0 /* Rx No Buffers Count - R/clr */
+#define E1000_RUC 0x040A4 /* Rx Undersize Count - R/clr */
+#define E1000_RFC 0x040A8 /* Rx Fragment Count - R/clr */
+#define E1000_ROC 0x040AC /* Rx Oversize Count - R/clr */
+#define E1000_RJC 0x040B0 /* Rx Jabber Count - R/clr */
+#define E1000_MGTPRC 0x040B4 /* Management Packets Rx Count - R/clr */
+#define E1000_MGTPDC 0x040B8 /* Management Packets Dropped Count - R/clr */
+#define E1000_MGTPTC 0x040BC /* Management Packets Tx Count - R/clr */
+#define E1000_TORL 0x040C0 /* Total Octets Rx Low - R/clr */
+#define E1000_TORH 0x040C4 /* Total Octets Rx High - R/clr */
+#define E1000_TOTL 0x040C8 /* Total Octets Tx Low - R/clr */
+#define E1000_TOTH 0x040CC /* Total Octets Tx High - R/clr */
+#define E1000_TPR 0x040D0 /* Total Packets Rx - R/clr */
+#define E1000_TPT 0x040D4 /* Total Packets Tx - R/clr */
+#define E1000_PTC64 0x040D8 /* Packets Tx (64 bytes) - R/clr */
+#define E1000_PTC127 0x040DC /* Packets Tx (65-127 bytes) - R/clr */
+#define E1000_PTC255 0x040E0 /* Packets Tx (128-255 bytes) - R/clr */
+#define E1000_PTC511 0x040E4 /* Packets Tx (256-511 bytes) - R/clr */
+#define E1000_PTC1023 0x040E8 /* Packets Tx (512-1023 bytes) - R/clr */
+#define E1000_PTC1522 0x040EC /* Packets Tx (1024-1522 Bytes) - R/clr */
+#define E1000_MPTC 0x040F0 /* Multicast Packets Tx Count - R/clr */
+#define E1000_BPTC 0x040F4 /* Broadcast Packets Tx Count - R/clr */
+#define E1000_TSCTC 0x040F8 /* TCP Segmentation Context Tx - R/clr */
+#define E1000_TSCTFC 0x040FC /* TCP Segmentation Context Tx Fail - R/clr */
+#define E1000_IAC 0x04100 /* Interrupt Assertion Count */
+#define E1000_ICRXPTC 0x04104 /* Interrupt Cause Rx Pkt Timer Expire Count */
+#define E1000_ICRXATC 0x04108 /* Interrupt Cause Rx Abs Timer Expire Count */
+#define E1000_ICTXPTC 0x0410C /* Interrupt Cause Tx Pkt Timer Expire Count */
+#define E1000_ICTXATC 0x04110 /* Interrupt Cause Tx Abs Timer Expire Count */
+#define E1000_ICTXQEC 0x04118 /* Interrupt Cause Tx Queue Empty Count */
+#define E1000_ICTXQMTC 0x0411C /* Interrupt Cause Tx Queue Min Thresh Count */
+#define E1000_ICRXDMTC 0x04120 /* Interrupt Cause Rx Desc Min Thresh Count */
+#define E1000_ICRXOC 0x04124 /* Interrupt Cause Receiver Overrun Count */
+#define E1000_CRC_OFFSET 0x05F50 /* CRC Offset register */
+
+#define E1000_PCS_CFG0 0x04200 /* PCS Configuration 0 - RW */
+#define E1000_PCS_LCTL 0x04208 /* PCS Link Control - RW */
+#define E1000_PCS_LSTAT 0x0420C /* PCS Link Status - RO */
+#define E1000_CBTMPC 0x0402C /* Circuit Breaker Tx Packet Count */
+#define E1000_HTDPMC 0x0403C /* Host Transmit Discarded Packets */
+#define E1000_CBRDPC 0x04044 /* Circuit Breaker Rx Dropped Count */
+#define E1000_CBRMPC 0x040FC /* Circuit Breaker Rx Packet Count */
+#define E1000_RPTHC 0x04104 /* Rx Packets To Host */
+#define E1000_HGPTC 0x04118 /* Host Good Packets Tx Count */
+#define E1000_HTCBDPC 0x04124 /* Host Tx Circuit Breaker Dropped Count */
+#define E1000_HGORCL 0x04128 /* Host Good Octets Received Count Low */
+#define E1000_HGORCH 0x0412C /* Host Good Octets Received Count High */
+#define E1000_HGOTCL 0x04130 /* Host Good Octets Transmit Count Low */
+#define E1000_HGOTCH 0x04134 /* Host Good Octets Transmit Count High */
+#define E1000_LENERRS 0x04138 /* Length Errors Count */
+#define E1000_SCVPC 0x04228 /* SerDes/SGMII Code Violation Pkt Count */
+#define E1000_HRMPC 0x0A018 /* Header Redirection Missed Packet Count */
+#define E1000_PCS_ANADV 0x04218 /* AN advertisement - RW */
+#define E1000_PCS_LPAB 0x0421C /* Link Partner Ability - RW */
+#define E1000_PCS_NPTX 0x04220 /* AN Next Page Transmit - RW */
+#define E1000_PCS_LPABNP 0x04224 /* Link Partner Ability Next Page - RW */
+#define E1000_1GSTAT_RCV 0x04228 /* 1GSTAT Code Violation Packet Count - RW */
+#define E1000_RXCSUM 0x05000 /* Rx Checksum Control - RW */
+#define E1000_RLPML 0x05004 /* Rx Long Packet Max Length */
+#define E1000_RFCTL 0x05008 /* Receive Filter Control*/
+#define E1000_MTA 0x05200 /* Multicast Table Array - RW Array */
+#define E1000_RA 0x05400 /* Receive Address - RW Array */
+#define E1000_VFTA 0x05600 /* VLAN Filter Table Array - RW Array */
+#define E1000_VT_CTL 0x0581C /* VMDq Control - RW */
+#define E1000_VFQA0 0x0B000 /* VLAN Filter Queue Array 0 - RW Array */
+#define E1000_VFQA1 0x0B200 /* VLAN Filter Queue Array 1 - RW Array */
+#define E1000_WUC 0x05800 /* Wakeup Control - RW */
+#define E1000_WUFC 0x05808 /* Wakeup Filter Control - RW */
+#define E1000_WUS 0x05810 /* Wakeup Status - RO */
+#define E1000_MANC 0x05820 /* Management Control - RW */
+#define E1000_IPAV 0x05838 /* IP Address Valid - RW */
+#define E1000_IP4AT 0x05840 /* IPv4 Address Table - RW Array */
+#define E1000_IP6AT 0x05880 /* IPv6 Address Table - RW Array */
+#define E1000_WUPL 0x05900 /* Wakeup Packet Length - RW */
+#define E1000_WUPM 0x05A00 /* Wakeup Packet Memory - RO A */
+#define E1000_PBACL 0x05B68 /* MSIx PBA Clear - Read/Write 1's to clear */
+#define E1000_FFLT 0x05F00 /* Flexible Filter Length Table - RW Array */
+#define E1000_HOST_IF 0x08800 /* Host Interface */
+#define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */
+#define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */
+
+#define E1000_KMRNCTRLSTA 0x00034 /* MAC-PHY interface - RW */
+#define E1000_MDPHYA 0x0003C /* PHY address - RW */
+#define E1000_MANC2H 0x05860 /* Management Control To Host - RW */
+#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */
+#define E1000_CCMCTL 0x05B48 /* CCM Control Register */
+#define E1000_GIOCTL 0x05B44 /* GIO Analog Control Register */
+#define E1000_SCCTL 0x05B4C /* PCIc PLL Configuration Register */
+#define E1000_GCR 0x05B00 /* PCI-Ex Control */
+#define E1000_GCR2 0x05B64 /* PCI-Ex Control #2 */
+#define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */
+#define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */
+#define E1000_GSCL_3 0x05B18 /* PCI-Ex Statistic Control #3 */
+#define E1000_GSCL_4 0x05B1C /* PCI-Ex Statistic Control #4 */
+#define E1000_FACTPS 0x05B30 /* Function Active and Power State to MNG */
+#define E1000_SWSM 0x05B50 /* SW Semaphore */
+#define E1000_FWSM 0x05B54 /* FW Semaphore */
+#define E1000_SWSM2 0x05B58 /* Driver-only SW semaphore (not used by BOOT agents) */
+#define E1000_DCA_ID 0x05B70 /* DCA Requester ID Information - RO */
+#define E1000_DCA_CTRL 0x05B74 /* DCA Control - RW */
+#define E1000_FFLT_DBG 0x05F04 /* Debug Register */
+#define E1000_HICR 0x08F00 /* Host Interface Control */
+
+/* RSS registers */
+#define E1000_CPUVEC 0x02C10 /* CPU Vector Register - RW */
+#define E1000_MRQC 0x05818 /* Multiple Receive Control - RW */
+#define E1000_IMIR(_i) (0x05A80 + ((_i) * 4)) /* Immediate Interrupt */
+#define E1000_IMIREXT(_i) (0x05AA0 + ((_i) * 4)) /* Immediate Interrupt Ext*/
+#define E1000_IMIRVP 0x05AC0 /* Immediate Interrupt Rx VLAN Priority - RW */
+#define E1000_MSIXBM(_i) (0x01600 + ((_i) * 4)) /* MSI-X Allocation Register
+ * (_i) - RW */
+#define E1000_MSIXTADD(_i) (0x0C000 + ((_i) * 0x10)) /* MSI-X Table entry addr
+ * low reg - RW */
+#define E1000_MSIXTUADD(_i) (0x0C004 + ((_i) * 0x10)) /* MSI-X Table entry addr
+ * upper reg - RW */
+#define E1000_MSIXTMSG(_i) (0x0C008 + ((_i) * 0x10)) /* MSI-X Table entry
+ * message reg - RW */
+#define E1000_MSIXVCTRL(_i) (0x0C00C + ((_i) * 0x10)) /* MSI-X Table entry
+ * vector ctrl reg - RW */
+#define E1000_MSIXPBA 0x0E000 /* MSI-X Pending bit array */
+#define E1000_RETA(_i) (0x05C00 + ((_i) * 4)) /* Redirection Table - RW */
+#define E1000_RSSRK(_i) (0x05C80 + ((_i) * 4)) /* RSS Random Key - RW */
+#define E1000_RSSIM 0x05864 /* RSS Interrupt Mask */
+#define E1000_RSSIR 0x05868 /* RSS Interrupt Request */
+#define E1000_RXMTRL 0x0B634 /* Time sync Rx EtherType and Msg Type - RW */
+#define E1000_RXUDP 0x0B638 /* Time Sync Rx UDP Port - RW */
+
+#endif
#define ERRFILE_w89c840 ( ERRFILE_DRIVER | 0x00460000 )
#define ERRFILE_ipoib ( ERRFILE_DRIVER | 0x00470000 )
#define ERRFILE_e1000_main ( ERRFILE_DRIVER | 0x00480000 )
+#define ERRFILE_e1000e_main ( ERRFILE_DRIVER | 0x00490000 )
#define ERRFILE_mtnic ( ERRFILE_DRIVER | 0x004a0000 )
#define ERRFILE_phantom ( ERRFILE_DRIVER | 0x004b0000 )
#define ERRFILE_ne2k_isa ( ERRFILE_DRIVER | 0x004c0000 )
projects / thirdparty / ipxe.git / commitdiff
