Merge tag 'qcom-arm64-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git...

Qualcomm ARM64 DT updates for v5.19

This adds MDIO bus description on the IPQ6018 platform.

On MSM8916 the BAM-DMUX WWAN network device is added and the Huawei
Ascend G7 gains sound card definition and clarified installation
instructions.

MSM8992 and MSM8994 continues to be worked on, gaining multimedia clock
controller, on-chip memory, watchdog and various cleanup changes. The
Xiaomi Mi 4C gains CPU regulators and fixes to the framebuffer
definition, while Huawei Nexus 6P gains eMMC support.

On MSM8996 the modem and sensor remtoeprocs are added and enabled in the
Dragonboard 820c and the Xiaomi devices.

On MSM8998 a few newly added clocks related to the sensor subsystem bus
are marked as protected by default and the OnePlus devices gains NFC.

The SC7180 platform and devices thereon are further polished and
limozeen moves to using edp-panel for EDID-based detection, over
statically defined panels.

On SC7280 GPI DMA, WiFi remoteproc and network device, LPASS audio
clocks, resets for SDCC controllers and a new CRD revision are added. A
supply glitch on the PCIe power and a current leak for Bluetooth during
suspend are corrected. The Herobrine board gains eDP support and the IDP
gains backlight. USB is marked wakeup capable.

On SDM845 the IPA, WLED based backlight and second WiFi channel are
enabled for Xiaomi Pocophone F1, the firmware name is modified to not
conflict with other boards.  On RB3 the CAN bus controller is added and
the WiFi calibration variant is defined to allow adding the board's
calibration information into linux-firmware.

SM6350 gains I2C busses, UFS and WiFi support, and the numbering of
uart9 is corrected.

On SM7225 and the Fairphone 4 UFS, WiFi and haptics are enabled.

On SM8150 PCIe, Ethernet and uSD card support is added, and enabled for
the SA8155p ADP board. The PDC interrupt controller is also added and
described as wakup interrupt parent for TLMM.

Camera subsystem and control interface are defined for SM8250. On the
Sony Xperia 1 II the audio amplifiers are enabled.

On SM8350 GPI DMA engines are added and linked to the I2C and SPI
serial engines. Surface Duo 2 gains battery charger support.

On SM8450 the two PCIe controller/PHYs are enabled, GPI DMA and QUP
serial engine instances are added. Remoteproc instances are enabled on
SM8450 HDK.

Last, but not least, a number of DeviceTree validation errors across
various boards are corrected.

* tag 'qcom-arm64-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (150 commits)
  arm64: dts: qcom: Only include sc7180.dtsi in sc7180-trogdor.dtsi
  arm64: dts: qcom: sc7180-trogdor: Simplify spi0/spi6 labeling
  arm64: dts: qcom: sc7180-trogdor: Simplify trackpad enabling
  arm64: dts: qcom: sc7280: eDP for herobrine boards
  arm64: dts: qcom: sa8155p-adp: Disable multiple Tx and Rx queues for ethernet IP
  arm64: dts: qcom: sm8150: Fix iommu sid value for SDC2 controller
  arm64: dts: qcom: sm8350-duo2: enable battery charger
  arm64: dts: qcom: Enable pm8350c pwm for sc7280-idp2
  arm64: dts: qcom: pm8350c: Add pwm support
  arm64: dts: qcom: sc7280-qcard: Configure CTS pin to bias-bus-hold for bluetooth
  arm64: dts: qcom: sc7280-idp: Configure CTS pin to bias-bus-hold for bluetooth
  arm64: dts: qcom: sc7180: Remove ipa interconnect node
  arm64: dts: qcom: sc7280-idp: Enable GPI DMAs
  arm64: dts: qcom: sc7280: Add GENI I2C/SPI DMA channels
  arm64: dts: qcom: sc7280: Add GPI DMAengines
  arm64: dts: qcom: sm8450: Fix qmp phy node (use phy@ instead of lanes@)
  arm64: dts: qcom: db845c: Add support for MCP2517FD
  arm64: dts: qcom: qrb5165-rb5: Fix can-clock node name
  arm64: dts: qcom: sc7280: Add SAR sensors to herobrine crd
  arm64: dts: qcom: sm8250: camss: Add CCI definitions
  ...

Link: https://lore.kernel.org/r/20220509204451.325675-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>