--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "ASUS Lyra Mini MAP-AC1300";
+ compatible = "asus,map-ac1300";
+
+ aliases {
+ led-boot = &led_blue0;
+ led-failsafe = &led_red0;
+ led-running = &led_blue0;
+ led-upgrade = &led_red0;
+ ethernet1 = &swport4;
+ label-mac-device = &wifi0;
+ };
+
+ soc {
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&prng {
+ status = "okay";
+};
+
+&crypto {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ status = "okay";
+
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>,
+ <&tlmm 1 GPIO_ACTIVE_LOW>;
+
+ flash@0 {
+ /*
+ * U-boot looks for "n25q128a11" node,
+ * if we don't have it, it will spit out the following warning:
+ * "ipq: fdt fixup unable to find compatible node".
+ */
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ linux,modalias = "m25p80", "mx25l1606e", "n25q128a11";
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ partition@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ partition@d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ partition@e0000 {
+ label = "APPSBLENV"; /* uboot env*/
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+ partition@f0000 {
+ label = "APPSBL"; /* uboot */
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+ partition@170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+ /* 0x00180000 - 0x00200000 unused */
+ };
+ };
+
+ spi-nand@1 {
+ compatible = "spi-nand";
+ reg = <1>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ compatible = "linux,ubi";
+ reg = <0x00000000 0x08000000>;
+ label = "ubi";
+
+ volumes {
+ ubi_factory: ubi-volume-factory {
+ volname = "Factory";
+ };
+ };
+ };
+ };
+ };
+};
+
+&ubi_factory {
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ precal_factory_1000: precal@1000 {
+ reg = <0x1000 0x2f20>;
+ };
+
+ macaddr_factory_1006: macaddr@1006 {
+ reg = <0x1006 0x6>;
+ };
+
+ precal_factory_5000: precal@5000 {
+ reg = <0x5000 0x2f20>;
+ };
+
+ macaddr_factory_5006: macaddr@5006 {
+ reg = <0x5006 0x6>;
+ };
+ };
+};
+
+&tlmm {
+ i2c_0_pins: i2c_0_pinmux {
+ pinmux {
+ function = "blsp_i2c0";
+ pins = "gpio58", "gpio59";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ mux {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ mux_cs {
+ function = "gpio";
+ pins = "gpio54", "gpio1";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+
+ nvmem-cell-names = "pre-calibration";
+ nvmem-cells = <&precal_factory_1000>;
+ qcom,ath10k-calibration-variant = "ASUS-MAP-AC1300";
+};
+
+&wifi1 {
+ status = "okay";
+
+ nvmem-cell-names = "pre-calibration";
+ nvmem-cells = <&precal_factory_5000>;
+ qcom,ath10k-calibration-variant = "ASUS-MAP-AC1300";
+};
+
+&usb2_hs_phy {
+ /* Bluetooth module attached via USB */
+ status = "okay";
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&blsp1_i2c3 {
+ status = "okay";
+
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+
+ led-controller@32 {
+ /* 9-channel RGB LED controller */
+ compatible = "national,lp5523";
+ reg = <0x32>;
+ clock-mode = /bits/ 8 <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /*
+ * There is only one single extremely bright RGB-LED.
+ * The RGB-color channels are running in parallel to
+ * increase the current delivery capabilities beyond
+ * what a single PWM-output of the controller can do.
+ */
+
+ led_blue0: led@0 {
+ chan-name = "blue-0";
+ led-cur = /bits/ 8 <0x80>;
+ max-cur = /bits/ 8 <0xff>;
+ reg = <0>;
+ color = <LED_COLOR_ID_BLUE>;
+ function-enumerator = <0>;
+ };
+
+ led@1 {
+ chan-name = "blue-1";
+ led-cur = /bits/ 8 <0x80>;
+ max-cur = /bits/ 8 <0xff>;
+ reg = <1>;
+ color = <LED_COLOR_ID_BLUE>;
+ function-enumerator = <1>;
+ };
+
+ led@2 {
+ chan-name = "blue-2";
+ led-cur = /bits/ 8 <0x80>;
+ max-cur = /bits/ 8 <0xff>;
+ reg = <2>;
+ color = <LED_COLOR_ID_BLUE>;
+ function-enumerator = <2>;
+ };
+
+ led_green0: led@3 {
+ chan-name = "green-0";
+ led-cur = /bits/ 8 <0x80>;
+ max-cur = /bits/ 8 <0xff>;
+ reg = <3>;
+ color = <LED_COLOR_ID_GREEN>;
+ function-enumerator = <0>;
+ };
+
+ led@4 {
+ chan-name = "green-1";
+ led-cur = /bits/ 8 <0x80>;
+ max-cur = /bits/ 8 <0xff>;
+ reg = <4>;
+ color = <LED_COLOR_ID_GREEN>;
+ function-enumerator = <1>;
+ };
+
+ led@5 {
+ chan-name = "green-2";
+ led-cur = /bits/ 8 <0x80>;
+ max-cur = /bits/ 8 <0xff>;
+ reg = <5>;
+ color = <LED_COLOR_ID_GREEN>;
+ function-enumerator = <2>;
+ };
+
+ led_red0: led@6 {
+ chan-name = "red-0";
+ led-cur = /bits/ 8 <0x80>;
+ max-cur = /bits/ 8 <0xff>;
+ reg = <6>;
+ color = <LED_COLOR_ID_RED>;
+ function-enumerator = <0>;
+ };
+
+ led@7 {
+ chan-name = "red-1";
+ led-cur = /bits/ 8 <0x80>;
+ max-cur = /bits/ 8 <0xff>;
+ reg = <7>;
+ color = <LED_COLOR_ID_RED>;
+ function-enumerator = <1>;
+ };
+
+ led@8 {
+ chan-name = "red-2";
+ led-cur = /bits/ 8 <0x80>;
+ max-cur = /bits/ 8 <0xff>;
+ reg = <8>;
+ color = <LED_COLOR_ID_RED>;
+ function-enumerator = <2>;
+ };
+ };
+};
+
+&blsp1_uart1 {
+ status = "okay";
+
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+};
+
+&mdio {
+ status = "okay";
+};
+
+&gmac {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_factory_1006 1>;
+ nvmem-cell-names = "mac-address";
+};
+
+&switch {
+ status = "okay";
+};
+
+&swport4 {
+ status = "okay";
+
+ label = "wan";
+ nvmem-cells = <&macaddr_factory_1006 3>;
+ nvmem-cell-names = "mac-address";
+};
+
+&swport5 {
+ status = "okay";
+
+ label = "lan";
+};
projects / thirdparty / openwrt.git / commitdiff
