From: Raphael Gallais-Pou Date: Fri, 12 Sep 2025 11:36:10 +0000 (+0200) Subject: media: doc/dt-bindings: remove support of stih407-c8sectpfe X-Git-Tag: v6.19-rc1~159^2~225 X-Git-Url: http://git.ipfire.org/?a=commitdiff_plain;h=203ee65bfdb29753d1a4d2f8efba6c0c7eccdd71;p=thirdparty%2Fkernel%2Flinux.git media: doc/dt-bindings: remove support of stih407-c8sectpfe Remove files documentation from stih407-c8sectpfe driver. Signed-off-by: Raphael Gallais-Pou Reviewed-by: Patrice Chotard Acked-by: Rob Herring (Arm) Signed-off-by: Hans Verkuil [hverkuil: slight change of the Subject, mention doc changes as well] --- diff --git a/Documentation/admin-guide/media/platform-cardlist.rst b/Documentation/admin-guide/media/platform-cardlist.rst index 1230ae4037ad5..63f4b19c3628f 100644 --- a/Documentation/admin-guide/media/platform-cardlist.rst +++ b/Documentation/admin-guide/media/platform-cardlist.rst @@ -18,8 +18,6 @@ am437x-vpfe TI AM437x VPFE aspeed-video Aspeed AST2400 and AST2500 atmel-isc ATMEL Image Sensor Controller (ISC) atmel-isi ATMEL Image Sensor Interface (ISI) -c8sectpfe SDR platform devices -c8sectpfe SDR platform devices cafe_ccic Marvell 88ALP01 (Cafe) CMOS Camera Controller cdns-csi2rx Cadence MIPI-CSI2 RX Controller cdns-csi2tx Cadence MIPI-CSI2 TX Controller diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt deleted file mode 100644 index 880d4d70c9fd7..0000000000000 --- a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt +++ /dev/null @@ -1,88 +0,0 @@ -STMicroelectronics STi c8sectpfe binding -============================================ - -This document describes the c8sectpfe device bindings that is used to get transport -stream data into the SoC on the TS pins, and into DDR for further processing. - -It is typically used in conjunction with one or more demodulator and tuner devices -which converts from the RF to digital domain. Demodulators and tuners are usually -located on an external DVB frontend card connected to SoC TS input pins. - -Currently 7 TS input (tsin) channels are supported on the stih407 family SoC. - -Required properties (controller (parent) node): -- compatible : Should be "stih407-c8sectpfe" - -- reg : Address and length of register sets for each device in - "reg-names" - -- reg-names : The names of the register addresses corresponding to the - registers filled in "reg": - - c8sectpfe: c8sectpfe registers - - c8sectpfe-ram: c8sectpfe internal sram - -- clocks : phandle list of c8sectpfe clocks -- clock-names : should be "c8sectpfe" -See: Documentation/devicetree/bindings/clock/clock-bindings.txt - -- pinctrl-names : a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num) - must be defined for each tsin child node. -- pinctrl-0 : phandle referencing pin configuration for this tsin configuration -See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt - - -Required properties (tsin (child) node): - -- tsin-num : tsin id of the InputBlock (must be between 0 to 6) -- i2c-bus : phandle to the I2C bus DT node which the demodulators & tuners on this tsin channel are connected. -- reset-gpios : reset gpio for this tsin channel. - -Optional properties (tsin (child) node): - -- invert-ts-clk : Bool property to control sense of ts input clock (data stored on falling edge of clk). -- serial-not-parallel : Bool property to configure input bus width (serial on ts_data<7>). -- async-not-sync : Bool property to control if data is received in asynchronous mode - (all bits/bytes with ts_valid or ts_packet asserted are valid). - -- dvb-card : Describes the NIM card connected to this tsin channel. - -Example: - -/* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */ - - c8sectpfe@8a20000 { - compatible = "st,stih407-c8sectpfe"; - reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>; - reg-names = "stfe", "stfe-ram"; - interrupts = , ; - interrupt-names = "stfe-error-irq", "stfe-idle-irq"; - pinctrl-0 = <&pinctrl_tsin0_serial>; - pinctrl-1 = <&pinctrl_tsin0_parallel>; - pinctrl-2 = <&pinctrl_tsin3_serial>; - pinctrl-3 = <&pinctrl_tsin4_serial_alt3>; - pinctrl-4 = <&pinctrl_tsin5_serial_alt1>; - pinctrl-names = "tsin0-serial", - "tsin0-parallel", - "tsin3-serial", - "tsin4-serial", - "tsin5-serial"; - clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>; - clock-names = "c8sectpfe"; - - /* tsin0 is TSA on NIMA */ - tsin0: port@0 { - tsin-num = <0>; - serial-not-parallel; - i2c-bus = <&ssc2>; - reset-gpios = <&pio15 4 GPIO_ACTIVE_HIGH>; - dvb-card = ; - }; - - tsin3: port@3 { - tsin-num = <3>; - serial-not-parallel; - i2c-bus = <&ssc3>; - reset-gpios = <&pio15 7 GPIO_ACTIVE_HIGH>; - dvb-card = ; - }; - };