From: Frank Li <Frank.Li@nxp.com>
Date: Tue, 28 Oct 2025 20:30:42 +0000 (-0400)
Subject: arm64: dts: imx8qm-mek: add state_100mhz and state_200mhz for usdhc
X-Git-Tag: v6.19-rc1~100^2~20^2~50
X-Git-Url: http://git.ipfire.org/?a=commitdiff_plain;h=2984af793281bc269fc8de3a204400fbfdbe42a7;p=thirdparty%2Flinux.git

arm64: dts: imx8qm-mek: add state_100mhz and state_200mhz for usdhc

default, state_100mhz and state_200mhz use the same settings. But current
driver use these to indicate if sd3.0 support.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
---

diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index 09b01e56ea004..0371de764e24c 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -811,8 +811,10 @@
 };
 
 &usdhc1 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1>;
+	pinctrl-2 = <&pinctrl_usdhc1>;
 	bus-width = <8>;
 	no-sd;
 	no-sdio;
@@ -821,8 +823,10 @@
 };
 
 &usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
 	bus-width = <4>;
 	vmmc-supply = <&reg_usdhc2_vmmc>;
 	cd-gpios = <&lsio_gpio5 22 GPIO_ACTIVE_LOW>;
@@ -1239,4 +1243,12 @@
 			IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000021
 		>;
 	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			IMX8QM_USDHC1_DATA6_LSIO_GPIO5_IO21			0x00000021
+			IMX8QM_USDHC1_DATA7_LSIO_GPIO5_IO22			0x00000021
+			IMX8QM_USDHC1_RESET_B_LSIO_GPIO4_IO07			0x00000021
+		>;
+	};
 };