From: Vincent Bernat Date: Sat, 6 Aug 2016 22:03:16 +0000 (+0200) Subject: include: update linux/ethtool.h to 4.7 X-Git-Tag: 0.9.5~23 X-Git-Url: http://git.ipfire.org/?a=commitdiff_plain;h=34c87bbd874746aca30b89e604c7c94cab1257a8;p=thirdparty%2Flldpd.git include: update linux/ethtool.h to 4.7 This is needed to support ETHTOOL_GLINKSETTINGS. --- diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h index 0e90e9b5..21e4384d 100644 --- a/include/linux/ethtool.h +++ b/include/linux/ethtool.h @@ -10,45 +10,112 @@ * Portions Copyright (C) Sun Microsystems 2008 */ -#ifndef _LINUX_ETHTOOL_H -#define _LINUX_ETHTOOL_H +#ifndef _UAPI_LINUX_ETHTOOL_H +#define _UAPI_LINUX_ETHTOOL_H #include #include -/* This should work for both 32 and 64 bit userland. */ +#ifndef __KERNEL__ +#include /* for INT_MAX */ +#endif + +/* All structures exposed to userland should be defined such that they + * have the same layout for 32-bit and 64-bit userland. + */ + +/** + * struct ethtool_cmd - DEPRECATED, link control and status + * This structure is DEPRECATED, please use struct ethtool_link_settings. + * @cmd: Command number = %ETHTOOL_GSET or %ETHTOOL_SSET + * @supported: Bitmask of %SUPPORTED_* flags for the link modes, + * physical connectors and other link features for which the + * interface supports autonegotiation or auto-detection. + * Read-only. + * @advertising: Bitmask of %ADVERTISED_* flags for the link modes, + * physical connectors and other link features that are + * advertised through autonegotiation or enabled for + * auto-detection. + * @speed: Low bits of the speed, 1Mb units, 0 to INT_MAX or SPEED_UNKNOWN + * @duplex: Duplex mode; one of %DUPLEX_* + * @port: Physical connector type; one of %PORT_* + * @phy_address: MDIO address of PHY (transceiver); 0 or 255 if not + * applicable. For clause 45 PHYs this is the PRTAD. + * @transceiver: Historically used to distinguish different possible + * PHY types, but not in a consistent way. Deprecated. + * @autoneg: Enable/disable autonegotiation and auto-detection; + * either %AUTONEG_DISABLE or %AUTONEG_ENABLE + * @mdio_support: Bitmask of %ETH_MDIO_SUPPORTS_* flags for the MDIO + * protocols supported by the interface; 0 if unknown. + * Read-only. + * @maxtxpkt: Historically used to report TX IRQ coalescing; now + * obsoleted by &struct ethtool_coalesce. Read-only; deprecated. + * @maxrxpkt: Historically used to report RX IRQ coalescing; now + * obsoleted by &struct ethtool_coalesce. Read-only; deprecated. + * @speed_hi: High bits of the speed, 1Mb units, 0 to INT_MAX or SPEED_UNKNOWN + * @eth_tp_mdix: Ethernet twisted-pair MDI(-X) status; one of + * %ETH_TP_MDI_*. If the status is unknown or not applicable, the + * value will be %ETH_TP_MDI_INVALID. Read-only. + * @eth_tp_mdix_ctrl: Ethernet twisted pair MDI(-X) control; one of + * %ETH_TP_MDI_*. If MDI(-X) control is not implemented, reads + * yield %ETH_TP_MDI_INVALID and writes may be ignored or rejected. + * When written successfully, the link should be renegotiated if + * necessary. + * @lp_advertising: Bitmask of %ADVERTISED_* flags for the link modes + * and other link features that the link partner advertised + * through autonegotiation; 0 if unknown or not applicable. + * Read-only. + * + * The link speed in Mbps is split between @speed and @speed_hi. Use + * the ethtool_cmd_speed() and ethtool_cmd_speed_set() functions to + * access it. + * + * If autonegotiation is disabled, the speed and @duplex represent the + * fixed link mode and are writable if the driver supports multiple + * link modes. If it is enabled then they are read-only; if the link + * is up they represent the negotiated link mode; if the link is down, + * the speed is 0, %SPEED_UNKNOWN or the highest enabled speed and + * @duplex is %DUPLEX_UNKNOWN or the best enabled duplex mode. + * + * Some hardware interfaces may have multiple PHYs and/or physical + * connectors fitted or do not allow the driver to detect which are + * fitted. For these interfaces @port and/or @phy_address may be + * writable, possibly dependent on @autoneg being %AUTONEG_DISABLE. + * Otherwise, attempts to write different values may be ignored or + * rejected. + * + * Users should assume that all fields not marked read-only are + * writable and subject to validation by the driver. They should use + * %ETHTOOL_GSET to get the current values before making specific + * changes and then applying them with %ETHTOOL_SSET. + * + * Drivers that implement set_settings() should validate all fields + * other than @cmd that are not described as read-only or deprecated, + * and must ignore all fields described as read-only. + * + * Deprecated fields should be ignored by both users and drivers. + */ struct ethtool_cmd { __u32 cmd; - __u32 supported; /* Features this interface supports */ - __u32 advertising; /* Features this interface advertises */ - __u16 speed; /* The forced speed (lower bits) in - * Mbps. Please use - * ethtool_cmd_speed()/_set() to - * access it */ - __u8 duplex; /* Duplex, half or full */ - __u8 port; /* Which connector port */ - __u8 phy_address; /* MDIO PHY address (PRTAD for clause 45). - * May be read-only or read-write - * depending on the driver. - */ - __u8 transceiver; /* Which transceiver to use */ - __u8 autoneg; /* Enable or disable autonegotiation */ - __u8 mdio_support; /* MDIO protocols supported. Read-only. - * Not set by all drivers. - */ - __u32 maxtxpkt; /* Tx pkts before generating tx int */ - __u32 maxrxpkt; /* Rx pkts before generating rx int */ - __u16 speed_hi; /* The forced speed (upper - * bits) in Mbps. Please use - * ethtool_cmd_speed()/_set() to - * access it */ + __u32 supported; + __u32 advertising; + __u16 speed; + __u8 duplex; + __u8 port; + __u8 phy_address; + __u8 transceiver; + __u8 autoneg; + __u8 mdio_support; + __u32 maxtxpkt; + __u32 maxrxpkt; + __u16 speed_hi; __u8 eth_tp_mdix; - __u8 reserved2; - __u32 lp_advertising; /* Features the link partner advertises */ + __u8 eth_tp_mdix_ctrl; + __u32 lp_advertising; __u32 reserved[2]; }; -static __inline__ void ethtool_cmd_speed_set(struct ethtool_cmd *ep, +static inline void ethtool_cmd_speed_set(struct ethtool_cmd *ep, __u32 speed) { @@ -56,7 +123,7 @@ static __inline__ void ethtool_cmd_speed_set(struct ethtool_cmd *ep, ep->speed_hi = (__u16)(speed >> 16); } -static __inline__ __u32 ethtool_cmd_speed(const struct ethtool_cmd *ep) +static inline __u32 ethtool_cmd_speed(const struct ethtool_cmd *ep) { return (ep->speed_hi << 16) | ep->speed; } @@ -77,37 +144,70 @@ static __inline__ __u32 ethtool_cmd_speed(const struct ethtool_cmd *ep) #define ETHTOOL_FWVERS_LEN 32 #define ETHTOOL_BUSINFO_LEN 32 -/* these strings are set to whatever the driver author decides... */ +#define ETHTOOL_EROMVERS_LEN 32 + +/** + * struct ethtool_drvinfo - general driver and device information + * @cmd: Command number = %ETHTOOL_GDRVINFO + * @driver: Driver short name. This should normally match the name + * in its bus driver structure (e.g. pci_driver::name). Must + * not be an empty string. + * @version: Driver version string; may be an empty string + * @fw_version: Firmware version string; may be an empty string + * @erom_version: Expansion ROM version string; may be an empty string + * @bus_info: Device bus address. This should match the dev_name() + * string for the underlying bus device, if there is one. May be + * an empty string. + * @n_priv_flags: Number of flags valid for %ETHTOOL_GPFLAGS and + * %ETHTOOL_SPFLAGS commands; also the number of strings in the + * %ETH_SS_PRIV_FLAGS set + * @n_stats: Number of u64 statistics returned by the %ETHTOOL_GSTATS + * command; also the number of strings in the %ETH_SS_STATS set + * @testinfo_len: Number of results returned by the %ETHTOOL_TEST + * command; also the number of strings in the %ETH_SS_TEST set + * @eedump_len: Size of EEPROM accessible through the %ETHTOOL_GEEPROM + * and %ETHTOOL_SEEPROM commands, in bytes + * @regdump_len: Size of register dump returned by the %ETHTOOL_GREGS + * command, in bytes + * + * Users can use the %ETHTOOL_GSSET_INFO command to get the number of + * strings in any string set (from Linux 2.6.34). + * + * Drivers should set at most @driver, @version, @fw_version and + * @bus_info in their get_drvinfo() implementation. The ethtool + * core fills in the other fields using other driver operations. + */ struct ethtool_drvinfo { __u32 cmd; - char driver[32]; /* driver short name, "tulip", "eepro100" */ - char version[32]; /* driver version string */ - char fw_version[ETHTOOL_FWVERS_LEN]; /* firmware version string */ - char bus_info[ETHTOOL_BUSINFO_LEN]; /* Bus info for this IF. */ - /* For PCI devices, use pci_name(pci_dev). */ - char reserved1[32]; + char driver[32]; + char version[32]; + char fw_version[ETHTOOL_FWVERS_LEN]; + char bus_info[ETHTOOL_BUSINFO_LEN]; + char erom_version[ETHTOOL_EROMVERS_LEN]; char reserved2[12]; - /* - * Some struct members below are filled in - * using ops->get_sset_count(). Obtaining - * this info from ethtool_drvinfo is now - * deprecated; Use ETHTOOL_GSSET_INFO - * instead. - */ - __u32 n_priv_flags; /* number of flags valid in ETHTOOL_GPFLAGS */ - __u32 n_stats; /* number of u64's from ETHTOOL_GSTATS */ + __u32 n_priv_flags; + __u32 n_stats; __u32 testinfo_len; - __u32 eedump_len; /* Size of data from ETHTOOL_GEEPROM (bytes) */ - __u32 regdump_len; /* Size of data from ETHTOOL_GREGS (bytes) */ + __u32 eedump_len; + __u32 regdump_len; }; #define SOPASS_MAX 6 -/* wake-on-lan settings */ + +/** + * struct ethtool_wolinfo - Wake-On-Lan configuration + * @cmd: Command number = %ETHTOOL_GWOL or %ETHTOOL_SWOL + * @supported: Bitmask of %WAKE_* flags for supported Wake-On-Lan modes. + * Read-only. + * @wolopts: Bitmask of %WAKE_* flags for enabled Wake-On-Lan modes. + * @sopass: SecureOn(tm) password; meaningful only if %WAKE_MAGICSECURE + * is set in @wolopts. + */ struct ethtool_wolinfo { __u32 cmd; __u32 supported; __u32 wolopts; - __u8 sopass[SOPASS_MAX]; /* SecureOn(tm) password */ + __u8 sopass[SOPASS_MAX]; }; /* for passing single values */ @@ -116,20 +216,83 @@ struct ethtool_value { __u32 data; }; -/* for passing big chunks of data */ +enum tunable_id { + ETHTOOL_ID_UNSPEC, + ETHTOOL_RX_COPYBREAK, + ETHTOOL_TX_COPYBREAK, + /* + * Add your fresh new tubale attribute above and remember to update + * tunable_strings[] in net/core/ethtool.c + */ + __ETHTOOL_TUNABLE_COUNT, +}; + +enum tunable_type_id { + ETHTOOL_TUNABLE_UNSPEC, + ETHTOOL_TUNABLE_U8, + ETHTOOL_TUNABLE_U16, + ETHTOOL_TUNABLE_U32, + ETHTOOL_TUNABLE_U64, + ETHTOOL_TUNABLE_STRING, + ETHTOOL_TUNABLE_S8, + ETHTOOL_TUNABLE_S16, + ETHTOOL_TUNABLE_S32, + ETHTOOL_TUNABLE_S64, +}; + +struct ethtool_tunable { + __u32 cmd; + __u32 id; + __u32 type_id; + __u32 len; + void *data[0]; +}; + +/** + * struct ethtool_regs - hardware register dump + * @cmd: Command number = %ETHTOOL_GREGS + * @version: Dump format version. This is driver-specific and may + * distinguish different chips/revisions. Drivers must use new + * version numbers whenever the dump format changes in an + * incompatible way. + * @len: On entry, the real length of @data. On return, the number of + * bytes used. + * @data: Buffer for the register dump + * + * Users should use %ETHTOOL_GDRVINFO to find the maximum length of + * a register dump for the interface. They must allocate the buffer + * immediately following this structure. + */ struct ethtool_regs { __u32 cmd; - __u32 version; /* driver-specific, indicates different chips/revs */ - __u32 len; /* bytes */ + __u32 version; + __u32 len; __u8 data[0]; }; -/* for passing EEPROM chunks */ +/** + * struct ethtool_eeprom - EEPROM dump + * @cmd: Command number = %ETHTOOL_GEEPROM, %ETHTOOL_GMODULEEEPROM or + * %ETHTOOL_SEEPROM + * @magic: A 'magic cookie' value to guard against accidental changes. + * The value passed in to %ETHTOOL_SEEPROM must match the value + * returned by %ETHTOOL_GEEPROM for the same device. This is + * unused when @cmd is %ETHTOOL_GMODULEEEPROM. + * @offset: Offset within the EEPROM to begin reading/writing, in bytes + * @len: On entry, number of bytes to read/write. On successful + * return, number of bytes actually read/written. In case of + * error, this may indicate at what point the error occurred. + * @data: Buffer to read/write from + * + * Users may use %ETHTOOL_GDRVINFO or %ETHTOOL_GMODULEINFO to find + * the length of an on-board or module EEPROM, respectively. They + * must allocate the buffer immediately following this structure. + */ struct ethtool_eeprom { __u32 cmd; __u32 magic; - __u32 offset; /* in bytes */ - __u32 len; /* in bytes */ + __u32 offset; + __u32 len; __u8 data[0]; }; @@ -227,17 +390,18 @@ struct ethtool_modinfo { * @rate_sample_interval: How often to do adaptive coalescing packet rate * sampling, measured in seconds. Must not be zero. * - * Each pair of (usecs, max_frames) fields specifies this exit - * condition for interrupt coalescing: + * Each pair of (usecs, max_frames) fields specifies that interrupts + * should be coalesced until * (usecs > 0 && time_since_first_completion >= usecs) || * (max_frames > 0 && completed_frames >= max_frames) + * * It is illegal to set both usecs and max_frames to zero as this * would cause interrupts to never be generated. To disable * coalescing, set usecs = 0 and max_frames = 1. * * Some implementations ignore the value of max_frames and use the - * condition: - * time_since_first_completion >= usecs + * condition time_since_first_completion >= usecs + * * This is deprecated. Drivers for hardware that does not support * counting completions should validate that max_frames == !rx_usecs. * @@ -277,22 +441,37 @@ struct ethtool_coalesce { __u32 rate_sample_interval; }; -/* for configuring RX/TX ring parameters */ +/** + * struct ethtool_ringparam - RX/TX ring parameters + * @cmd: Command number = %ETHTOOL_GRINGPARAM or %ETHTOOL_SRINGPARAM + * @rx_max_pending: Maximum supported number of pending entries per + * RX ring. Read-only. + * @rx_mini_max_pending: Maximum supported number of pending entries + * per RX mini ring. Read-only. + * @rx_jumbo_max_pending: Maximum supported number of pending entries + * per RX jumbo ring. Read-only. + * @tx_max_pending: Maximum supported number of pending entries per + * TX ring. Read-only. + * @rx_pending: Current maximum number of pending entries per RX ring + * @rx_mini_pending: Current maximum number of pending entries per RX + * mini ring + * @rx_jumbo_pending: Current maximum number of pending entries per RX + * jumbo ring + * @tx_pending: Current maximum supported number of pending entries + * per TX ring + * + * If the interface does not have separate RX mini and/or jumbo rings, + * @rx_mini_max_pending and/or @rx_jumbo_max_pending will be 0. + * + * There may also be driver-dependent minimum values for the number + * of entries per ring. + */ struct ethtool_ringparam { - __u32 cmd; /* ETHTOOL_{G,S}RINGPARAM */ - - /* Read only attributes. These indicate the maximum number - * of pending RX/TX ring entries the driver will allow the - * user to set. - */ + __u32 cmd; __u32 rx_max_pending; __u32 rx_mini_max_pending; __u32 rx_jumbo_max_pending; __u32 tx_max_pending; - - /* Values changeable by the user. The valid values are - * in the range 1 to the "*_max_pending" counterpart above. - */ __u32 rx_pending; __u32 rx_mini_pending; __u32 rx_jumbo_pending; @@ -327,51 +506,101 @@ struct ethtool_channels { __u32 combined_count; }; -/* for configuring link flow control parameters */ +/** + * struct ethtool_pauseparam - Ethernet pause (flow control) parameters + * @cmd: Command number = %ETHTOOL_GPAUSEPARAM or %ETHTOOL_SPAUSEPARAM + * @autoneg: Flag to enable autonegotiation of pause frame use + * @rx_pause: Flag to enable reception of pause frames + * @tx_pause: Flag to enable transmission of pause frames + * + * Drivers should reject a non-zero setting of @autoneg when + * autoneogotiation is disabled (or not supported) for the link. + * + * If the link is autonegotiated, drivers should use + * mii_advertise_flowctrl() or similar code to set the advertised + * pause frame capabilities based on the @rx_pause and @tx_pause flags, + * even if @autoneg is zero. They should also allow the advertised + * pause frame capabilities to be controlled directly through the + * advertising field of &struct ethtool_cmd. + * + * If @autoneg is non-zero, the MAC is configured to send and/or + * receive pause frames according to the result of autonegotiation. + * Otherwise, it is configured directly based on the @rx_pause and + * @tx_pause flags. + */ struct ethtool_pauseparam { - __u32 cmd; /* ETHTOOL_{G,S}PAUSEPARAM */ - - /* If the link is being auto-negotiated (via ethtool_cmd.autoneg - * being true) the user may set 'autoneg' here non-zero to have the - * pause parameters be auto-negotiated too. In such a case, the - * {rx,tx}_pause values below determine what capabilities are - * advertised. - * - * If 'autoneg' is zero or the link is not being auto-negotiated, - * then {rx,tx}_pause force the driver to use/not-use pause - * flow control. - */ + __u32 cmd; __u32 autoneg; __u32 rx_pause; __u32 tx_pause; }; #define ETH_GSTRING_LEN 32 + +/** + * enum ethtool_stringset - string set ID + * @ETH_SS_TEST: Self-test result names, for use with %ETHTOOL_TEST + * @ETH_SS_STATS: Statistic names, for use with %ETHTOOL_GSTATS + * @ETH_SS_PRIV_FLAGS: Driver private flag names, for use with + * %ETHTOOL_GPFLAGS and %ETHTOOL_SPFLAGS + * @ETH_SS_NTUPLE_FILTERS: Previously used with %ETHTOOL_GRXNTUPLE; + * now deprecated + * @ETH_SS_FEATURES: Device feature names + * @ETH_SS_RSS_HASH_FUNCS: RSS hush function names + * @ETH_SS_PHY_STATS: Statistic names, for use with %ETHTOOL_GPHYSTATS + */ enum ethtool_stringset { ETH_SS_TEST = 0, ETH_SS_STATS, ETH_SS_PRIV_FLAGS, - ETH_SS_NTUPLE_FILTERS, /* Do not use, GRXNTUPLE is now deprecated */ + ETH_SS_NTUPLE_FILTERS, ETH_SS_FEATURES, + ETH_SS_RSS_HASH_FUNCS, + ETH_SS_TUNABLES, + ETH_SS_PHY_STATS, }; -/* for passing string sets for data tagging */ +/** + * struct ethtool_gstrings - string set for data tagging + * @cmd: Command number = %ETHTOOL_GSTRINGS + * @string_set: String set ID; one of &enum ethtool_stringset + * @len: On return, the number of strings in the string set + * @data: Buffer for strings. Each string is null-padded to a size of + * %ETH_GSTRING_LEN. + * + * Users must use %ETHTOOL_GSSET_INFO to find the number of strings in + * the string set. They must allocate a buffer of the appropriate + * size immediately following this structure. + */ struct ethtool_gstrings { - __u32 cmd; /* ETHTOOL_GSTRINGS */ - __u32 string_set; /* string set id e.c. ETH_SS_TEST, etc*/ - __u32 len; /* number of strings in the string set */ + __u32 cmd; + __u32 string_set; + __u32 len; __u8 data[0]; }; +/** + * struct ethtool_sset_info - string set information + * @cmd: Command number = %ETHTOOL_GSSET_INFO + * @sset_mask: On entry, a bitmask of string sets to query, with bits + * numbered according to &enum ethtool_stringset. On return, a + * bitmask of those string sets queried that are supported. + * @data: Buffer for string set sizes. On return, this contains the + * size of each string set that was queried and supported, in + * order of ID. + * + * Example: The user passes in @sset_mask = 0x7 (sets 0, 1, 2) and on + * return @sset_mask == 0x6 (sets 1, 2). Then @data[0] contains the + * size of set 1 and @data[1] contains the size of set 2. + * + * Users must allocate a buffer of the appropriate size (4 * number of + * sets queried) immediately following this structure. + */ struct ethtool_sset_info { - __u32 cmd; /* ETHTOOL_GSSET_INFO */ + __u32 cmd; __u32 reserved; - __u64 sset_mask; /* input: each bit selects an sset to query */ - /* output: each bit a returned sset */ - __u32 data[0]; /* ETH_SS_xxx count, in order, based on bits - in sset_mask. One bit implies one - __u32, two bits implies two - __u32's, etc. */ + __u64 sset_mask; + __u32 data[0]; }; /** @@ -391,24 +620,58 @@ enum ethtool_test_flags { ETH_TEST_FL_EXTERNAL_LB_DONE = (1 << 3), }; -/* for requesting NIC test and getting results*/ +/** + * struct ethtool_test - device self-test invocation + * @cmd: Command number = %ETHTOOL_TEST + * @flags: A bitmask of flags from &enum ethtool_test_flags. Some + * flags may be set by the user on entry; others may be set by + * the driver on return. + * @len: On return, the number of test results + * @data: Array of test results + * + * Users must use %ETHTOOL_GSSET_INFO or %ETHTOOL_GDRVINFO to find the + * number of test results that will be returned. They must allocate a + * buffer of the appropriate size (8 * number of results) immediately + * following this structure. + */ struct ethtool_test { - __u32 cmd; /* ETHTOOL_TEST */ - __u32 flags; /* ETH_TEST_FL_xxx */ + __u32 cmd; + __u32 flags; __u32 reserved; - __u32 len; /* result length, in number of u64 elements */ + __u32 len; __u64 data[0]; }; -/* for dumping NIC-specific statistics */ +/** + * struct ethtool_stats - device-specific statistics + * @cmd: Command number = %ETHTOOL_GSTATS + * @n_stats: On return, the number of statistics + * @data: Array of statistics + * + * Users must use %ETHTOOL_GSSET_INFO or %ETHTOOL_GDRVINFO to find the + * number of statistics that will be returned. They must allocate a + * buffer of the appropriate size (8 * number of statistics) + * immediately following this structure. + */ struct ethtool_stats { - __u32 cmd; /* ETHTOOL_GSTATS */ - __u32 n_stats; /* number of u64's being returned */ + __u32 cmd; + __u32 n_stats; __u64 data[0]; }; +/** + * struct ethtool_perm_addr - permanent hardware address + * @cmd: Command number = %ETHTOOL_GPERMADDR + * @size: On entry, the size of the buffer. On return, the size of the + * address. The command fails if the buffer is too small. + * @data: Buffer for the address + * + * Users must allocate the buffer immediately following this structure. + * A buffer size of %MAX_ADDR_LEN should be sufficient for any address + * type. + */ struct ethtool_perm_addr { - __u32 cmd; /* ETHTOOL_GPERMADDR */ + __u32 cmd; __u32 size; __u8 data[0]; }; @@ -490,6 +753,56 @@ struct ethtool_usrip4_spec { __u8 proto; }; +/** + * struct ethtool_tcpip6_spec - flow specification for TCP/IPv6 etc. + * @ip6src: Source host + * @ip6dst: Destination host + * @psrc: Source port + * @pdst: Destination port + * @tclass: Traffic Class + * + * This can be used to specify a TCP/IPv6, UDP/IPv6 or SCTP/IPv6 flow. + */ +struct ethtool_tcpip6_spec { + __be32 ip6src[4]; + __be32 ip6dst[4]; + __be16 psrc; + __be16 pdst; + __u8 tclass; +}; + +/** + * struct ethtool_ah_espip6_spec - flow specification for IPsec/IPv6 + * @ip6src: Source host + * @ip6dst: Destination host + * @spi: Security parameters index + * @tclass: Traffic Class + * + * This can be used to specify an IPsec transport or tunnel over IPv6. + */ +struct ethtool_ah_espip6_spec { + __be32 ip6src[4]; + __be32 ip6dst[4]; + __be32 spi; + __u8 tclass; +}; + +/** + * struct ethtool_usrip6_spec - general flow specification for IPv6 + * @ip6src: Source host + * @ip6dst: Destination host + * @l4_4_bytes: First 4 bytes of transport (layer 4) header + * @tclass: Traffic Class + * @l4_proto: Transport protocol number (nexthdr after any Extension Headers) + */ +struct ethtool_usrip6_spec { + __be32 ip6src[4]; + __be32 ip6dst[4]; + __be32 l4_4_bytes; + __u8 tclass; + __u8 l4_proto; +}; + union ethtool_flow_union { struct ethtool_tcpip4_spec tcp_ip4_spec; struct ethtool_tcpip4_spec udp_ip4_spec; @@ -497,14 +810,33 @@ union ethtool_flow_union { struct ethtool_ah_espip4_spec ah_ip4_spec; struct ethtool_ah_espip4_spec esp_ip4_spec; struct ethtool_usrip4_spec usr_ip4_spec; + struct ethtool_tcpip6_spec tcp_ip6_spec; + struct ethtool_tcpip6_spec udp_ip6_spec; + struct ethtool_tcpip6_spec sctp_ip6_spec; + struct ethtool_ah_espip6_spec ah_ip6_spec; + struct ethtool_ah_espip6_spec esp_ip6_spec; + struct ethtool_usrip6_spec usr_ip6_spec; struct ethhdr ether_spec; - __u8 hdata[60]; + __u8 hdata[52]; }; +/** + * struct ethtool_flow_ext - additional RX flow fields + * @h_dest: destination MAC address + * @vlan_etype: VLAN EtherType + * @vlan_tci: VLAN tag control information + * @data: user defined data + * + * Note, @vlan_etype, @vlan_tci, and @data are only valid if %FLOW_EXT + * is set in &struct ethtool_rx_flow_spec @flow_type. + * @h_dest is valid if %FLOW_MAC_EXT is set. + */ struct ethtool_flow_ext { - __be16 vlan_etype; - __be16 vlan_tci; - __be32 data[2]; + __u8 padding[2]; + unsigned char h_dest[ETH_ALEN]; + __be16 vlan_etype; + __be16 vlan_tci; + __be32 data[2]; }; /** @@ -515,7 +847,8 @@ struct ethtool_flow_ext { * @m_u: Masks for flow field bits to be matched * @m_ext: Masks for additional field bits to be matched * Note, all additional fields must be ignored unless @flow_type - * includes the %FLOW_EXT flag. + * includes the %FLOW_EXT or %FLOW_MAC_EXT flag + * (see &struct ethtool_flow_ext description). * @ring_cookie: RX ring/queue index to deliver to, or %RX_CLS_FLOW_DISC * if packets should be discarded * @location: Location of rule in the table. Locations must be @@ -532,6 +865,31 @@ struct ethtool_rx_flow_spec { __u32 location; }; +/* How rings are layed out when accessing virtual functions or + * offloaded queues is device specific. To allow users to do flow + * steering and specify these queues the ring cookie is partitioned + * into a 32bit queue index with an 8 bit virtual function id. + * This also leaves the 3bytes for further specifiers. It is possible + * future devices may support more than 256 virtual functions if + * devices start supporting PCIe w/ARI. However at the moment I + * do not know of any devices that support this so I do not reserve + * space for this at this time. If a future patch consumes the next + * byte it should be aware of this possiblity. + */ +#define ETHTOOL_RX_FLOW_SPEC_RING 0x00000000FFFFFFFFLL +#define ETHTOOL_RX_FLOW_SPEC_RING_VF 0x000000FF00000000LL +#define ETHTOOL_RX_FLOW_SPEC_RING_VF_OFF 32 +static inline __u64 ethtool_get_flow_spec_ring(__u64 ring_cookie) +{ + return ETHTOOL_RX_FLOW_SPEC_RING & ring_cookie; +}; + +static inline __u64 ethtool_get_flow_spec_ring_vf(__u64 ring_cookie) +{ + return (ETHTOOL_RX_FLOW_SPEC_RING_VF & ring_cookie) >> + ETHTOOL_RX_FLOW_SPEC_RING_VF_OFF; +}; + /** * struct ethtool_rxnfc - command to get or set RX flow classification rules * @cmd: Specific command number - %ETHTOOL_GRXFH, %ETHTOOL_SRXFH, @@ -577,7 +935,7 @@ struct ethtool_rx_flow_spec { * %ETHTOOL_SRXCLSRLINS may add the rule at any suitable unused * location, and may remove a rule at a later location (lower * priority) that matches exactly the same set of flows. The special - * values are: %RX_CLS_LOC_ANY, selecting any location; + * values are %RX_CLS_LOC_ANY, selecting any location; * %RX_CLS_LOC_FIRST, selecting the first suitable location (maximum * priority); and %RX_CLS_LOC_LAST, selecting the last suitable * location (minimum priority). Additional special values may be @@ -613,6 +971,42 @@ struct ethtool_rxfh_indir { __u32 ring_index[0]; }; +/** + * struct ethtool_rxfh - command to get/set RX flow hash indir or/and hash key. + * @cmd: Specific command number - %ETHTOOL_GRSSH or %ETHTOOL_SRSSH + * @rss_context: RSS context identifier. + * @indir_size: On entry, the array size of the user buffer for the + * indirection table, which may be zero, or (for %ETHTOOL_SRSSH), + * %ETH_RXFH_INDIR_NO_CHANGE. On return from %ETHTOOL_GRSSH, + * the array size of the hardware indirection table. + * @key_size: On entry, the array size of the user buffer for the hash key, + * which may be zero. On return from %ETHTOOL_GRSSH, the size of the + * hardware hash key. + * @hfunc: Defines the current RSS hash function used by HW (or to be set to). + * Valid values are one of the %ETH_RSS_HASH_*. + * @rsvd: Reserved for future extensions. + * @rss_config: RX ring/queue index for each hash value i.e., indirection table + * of @indir_size __u32 elements, followed by hash key of @key_size + * bytes. + * + * For %ETHTOOL_GRSSH, a @indir_size and key_size of zero means that only the + * size should be returned. For %ETHTOOL_SRSSH, an @indir_size of + * %ETH_RXFH_INDIR_NO_CHANGE means that indir table setting is not requested + * and a @indir_size of zero means the indir table should be reset to default + * values. An hfunc of zero means that hash function setting is not requested. + */ +struct ethtool_rxfh { + __u32 cmd; + __u32 rss_context; + __u32 indir_size; + __u32 key_size; + __u8 hfunc; + __u8 rsvd8[3]; + __u32 rsvd32; + __u32 rss_config[0]; +}; +#define ETH_RXFH_INDIR_NO_CHANGE 0xffffffff + /** * struct ethtool_rx_ntuple_flow_spec - specification for RX flow filter * @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW @@ -688,9 +1082,6 @@ struct ethtool_flash { * for %ETHTOOL_GET_DUMP_FLAG command * @data: data collected for get dump data operation */ - -#define ETH_FW_DUMP_DISABLE 0 - struct ethtool_dump { __u32 cmd; __u32 version; @@ -699,6 +1090,8 @@ struct ethtool_dump { __u8 data[0]; }; +#define ETH_FW_DUMP_DISABLE 0 + /* for returning and changing feature sets */ /** @@ -718,8 +1111,9 @@ struct ethtool_get_features_block { /** * struct ethtool_gfeatures - command to get state of device's features * @cmd: command number = %ETHTOOL_GFEATURES - * @size: in: number of elements in the features[] array; - * out: number of elements in features[] needed to hold all features + * @size: On entry, the number of elements in the features[] array; + * on return, the number of elements in features[] needed to hold + * all features * @features: state of features */ struct ethtool_gfeatures { @@ -762,6 +1156,11 @@ struct ethtool_sfeatures { * the 'hwtstamp_tx_types' and 'hwtstamp_rx_filters' enumeration values, * respectively. For example, if the device supports HWTSTAMP_TX_ON, * then (1 << HWTSTAMP_TX_ON) in 'tx_types' will be set. + * + * Drivers should only report the filters they actually support without + * upscaling in the SIOCSHWTSTAMP ioctl. If the SIOCSHWSTAMP request for + * HWTSTAMP_FILTER_V1_SYNC is supported by HWTSTAMP_FILTER_V1_EVENT, then the + * driver should only report HWTSTAMP_FILTER_V1_EVENT in this op. */ struct ethtool_ts_info { __u32 cmd; @@ -808,10 +1207,31 @@ enum ethtool_sfeatures_retval_bits { #define ETHTOOL_F_WISH (1 << ETHTOOL_F_WISH__BIT) #define ETHTOOL_F_COMPAT (1 << ETHTOOL_F_COMPAT__BIT) +#define MAX_NUM_QUEUE 4096 + +#if 0 +/** + * struct ethtool_per_queue_op - apply sub command to the queues in mask. + * @cmd: ETHTOOL_PERQUEUE + * @sub_command: the sub command which apply to each queues + * @queue_mask: Bitmap of the queues which sub command apply to + * @data: A complete command structure following for each of the queues addressed + */ +struct ethtool_per_queue_op { + __u32 cmd; + __u32 sub_command; + __u32 queue_mask[__KERNEL_DIV_ROUND_UP(MAX_NUM_QUEUE, 32)]; + char data[]; +}; +#endif /* CMDs currently supported */ -#define ETHTOOL_GSET 0x00000001 /* Get settings. */ -#define ETHTOOL_SSET 0x00000002 /* Set settings. */ +#define ETHTOOL_GSET 0x00000001 /* DEPRECATED, Get settings. + * Please use ETHTOOL_GLINKSETTINGS + */ +#define ETHTOOL_SSET 0x00000002 /* DEPRECATED, Set settings. + * Please use ETHTOOL_SLINKSETTINGS + */ #define ETHTOOL_GDRVINFO 0x00000003 /* Get driver info. */ #define ETHTOOL_GREGS 0x00000004 /* Get NIC registers. */ #define ETHTOOL_GWOL 0x00000005 /* Get wake-on-lan options. */ @@ -885,67 +1305,156 @@ enum ethtool_sfeatures_retval_bits { #define ETHTOOL_GEEE 0x00000044 /* Get EEE settings */ #define ETHTOOL_SEEE 0x00000045 /* Set EEE settings */ +#define ETHTOOL_GRSSH 0x00000046 /* Get RX flow hash configuration */ +#define ETHTOOL_SRSSH 0x00000047 /* Set RX flow hash configuration */ +#define ETHTOOL_GTUNABLE 0x00000048 /* Get tunable configuration */ +#define ETHTOOL_STUNABLE 0x00000049 /* Set tunable configuration */ +#define ETHTOOL_GPHYSTATS 0x0000004a /* get PHY-specific statistics */ + +#define ETHTOOL_PERQUEUE 0x0000004b /* Set per queue options */ + +#define ETHTOOL_GLINKSETTINGS 0x0000004c /* Get ethtool_link_settings */ +#define ETHTOOL_SLINKSETTINGS 0x0000004d /* Set ethtool_link_settings */ + + /* compatibility with older code */ #define SPARC_ETH_GSET ETHTOOL_GSET #define SPARC_ETH_SSET ETHTOOL_SSET -/* Indicates what features are supported by the interface. */ -#define SUPPORTED_10baseT_Half (1 << 0) -#define SUPPORTED_10baseT_Full (1 << 1) -#define SUPPORTED_100baseT_Half (1 << 2) -#define SUPPORTED_100baseT_Full (1 << 3) -#define SUPPORTED_1000baseT_Half (1 << 4) -#define SUPPORTED_1000baseT_Full (1 << 5) -#define SUPPORTED_Autoneg (1 << 6) -#define SUPPORTED_TP (1 << 7) -#define SUPPORTED_AUI (1 << 8) -#define SUPPORTED_MII (1 << 9) -#define SUPPORTED_FIBRE (1 << 10) -#define SUPPORTED_BNC (1 << 11) -#define SUPPORTED_10000baseT_Full (1 << 12) -#define SUPPORTED_Pause (1 << 13) -#define SUPPORTED_Asym_Pause (1 << 14) -#define SUPPORTED_2500baseX_Full (1 << 15) -#define SUPPORTED_Backplane (1 << 16) -#define SUPPORTED_1000baseKX_Full (1 << 17) -#define SUPPORTED_10000baseKX4_Full (1 << 18) -#define SUPPORTED_10000baseKR_Full (1 << 19) -#define SUPPORTED_10000baseR_FEC (1 << 20) -#define SUPPORTED_20000baseMLD2_Full (1 << 21) -#define SUPPORTED_20000baseKR2_Full (1 << 22) -#define SUPPORTED_40000baseKR4_Full (1 << 23) -#define SUPPORTED_40000baseCR4_Full (1 << 24) -#define SUPPORTED_40000baseSR4_Full (1 << 25) -#define SUPPORTED_40000baseLR4_Full (1 << 26) - -/* Indicates what features are advertised by the interface. */ -#define ADVERTISED_10baseT_Half (1 << 0) -#define ADVERTISED_10baseT_Full (1 << 1) -#define ADVERTISED_100baseT_Half (1 << 2) -#define ADVERTISED_100baseT_Full (1 << 3) -#define ADVERTISED_1000baseT_Half (1 << 4) -#define ADVERTISED_1000baseT_Full (1 << 5) -#define ADVERTISED_Autoneg (1 << 6) -#define ADVERTISED_TP (1 << 7) -#define ADVERTISED_AUI (1 << 8) -#define ADVERTISED_MII (1 << 9) -#define ADVERTISED_FIBRE (1 << 10) -#define ADVERTISED_BNC (1 << 11) -#define ADVERTISED_10000baseT_Full (1 << 12) -#define ADVERTISED_Pause (1 << 13) -#define ADVERTISED_Asym_Pause (1 << 14) -#define ADVERTISED_2500baseX_Full (1 << 15) -#define ADVERTISED_Backplane (1 << 16) -#define ADVERTISED_1000baseKX_Full (1 << 17) -#define ADVERTISED_10000baseKX4_Full (1 << 18) -#define ADVERTISED_10000baseKR_Full (1 << 19) -#define ADVERTISED_10000baseR_FEC (1 << 20) -#define ADVERTISED_20000baseMLD2_Full (1 << 21) -#define ADVERTISED_20000baseKR2_Full (1 << 22) -#define ADVERTISED_40000baseKR4_Full (1 << 23) -#define ADVERTISED_40000baseCR4_Full (1 << 24) -#define ADVERTISED_40000baseSR4_Full (1 << 25) -#define ADVERTISED_40000baseLR4_Full (1 << 26) +/* Link mode bit indices */ +enum ethtool_link_mode_bit_indices { + ETHTOOL_LINK_MODE_10baseT_Half_BIT = 0, + ETHTOOL_LINK_MODE_10baseT_Full_BIT = 1, + ETHTOOL_LINK_MODE_100baseT_Half_BIT = 2, + ETHTOOL_LINK_MODE_100baseT_Full_BIT = 3, + ETHTOOL_LINK_MODE_1000baseT_Half_BIT = 4, + ETHTOOL_LINK_MODE_1000baseT_Full_BIT = 5, + ETHTOOL_LINK_MODE_Autoneg_BIT = 6, + ETHTOOL_LINK_MODE_TP_BIT = 7, + ETHTOOL_LINK_MODE_AUI_BIT = 8, + ETHTOOL_LINK_MODE_MII_BIT = 9, + ETHTOOL_LINK_MODE_FIBRE_BIT = 10, + ETHTOOL_LINK_MODE_BNC_BIT = 11, + ETHTOOL_LINK_MODE_10000baseT_Full_BIT = 12, + ETHTOOL_LINK_MODE_Pause_BIT = 13, + ETHTOOL_LINK_MODE_Asym_Pause_BIT = 14, + ETHTOOL_LINK_MODE_2500baseX_Full_BIT = 15, + ETHTOOL_LINK_MODE_Backplane_BIT = 16, + ETHTOOL_LINK_MODE_1000baseKX_Full_BIT = 17, + ETHTOOL_LINK_MODE_10000baseKX4_Full_BIT = 18, + ETHTOOL_LINK_MODE_10000baseKR_Full_BIT = 19, + ETHTOOL_LINK_MODE_10000baseR_FEC_BIT = 20, + ETHTOOL_LINK_MODE_20000baseMLD2_Full_BIT = 21, + ETHTOOL_LINK_MODE_20000baseKR2_Full_BIT = 22, + ETHTOOL_LINK_MODE_40000baseKR4_Full_BIT = 23, + ETHTOOL_LINK_MODE_40000baseCR4_Full_BIT = 24, + ETHTOOL_LINK_MODE_40000baseSR4_Full_BIT = 25, + ETHTOOL_LINK_MODE_40000baseLR4_Full_BIT = 26, + ETHTOOL_LINK_MODE_56000baseKR4_Full_BIT = 27, + ETHTOOL_LINK_MODE_56000baseCR4_Full_BIT = 28, + ETHTOOL_LINK_MODE_56000baseSR4_Full_BIT = 29, + ETHTOOL_LINK_MODE_56000baseLR4_Full_BIT = 30, + ETHTOOL_LINK_MODE_25000baseCR_Full_BIT = 31, + ETHTOOL_LINK_MODE_25000baseKR_Full_BIT = 32, + ETHTOOL_LINK_MODE_25000baseSR_Full_BIT = 33, + ETHTOOL_LINK_MODE_50000baseCR2_Full_BIT = 34, + ETHTOOL_LINK_MODE_50000baseKR2_Full_BIT = 35, + ETHTOOL_LINK_MODE_100000baseKR4_Full_BIT = 36, + ETHTOOL_LINK_MODE_100000baseSR4_Full_BIT = 37, + ETHTOOL_LINK_MODE_100000baseCR4_Full_BIT = 38, + ETHTOOL_LINK_MODE_100000baseLR4_ER4_Full_BIT = 39, + + /* Last allowed bit for __ETHTOOL_LINK_MODE_LEGACY_MASK is bit + * 31. Please do NOT define any SUPPORTED_* or ADVERTISED_* + * macro for bits > 31. The only way to use indices > 31 is to + * use the new ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. + */ + + __ETHTOOL_LINK_MODE_LAST + = ETHTOOL_LINK_MODE_100000baseLR4_ER4_Full_BIT, +}; + +#define __ETHTOOL_LINK_MODE_LEGACY_MASK(base_name) \ + (1UL << (ETHTOOL_LINK_MODE_ ## base_name ## _BIT)) + +/* DEPRECATED macros. Please migrate to + * ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. Please do NOT + * define any new SUPPORTED_* macro for bits > 31. + */ +#define SUPPORTED_10baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Half) +#define SUPPORTED_10baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Full) +#define SUPPORTED_100baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Half) +#define SUPPORTED_100baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Full) +#define SUPPORTED_1000baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Half) +#define SUPPORTED_1000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Full) +#define SUPPORTED_Autoneg __ETHTOOL_LINK_MODE_LEGACY_MASK(Autoneg) +#define SUPPORTED_TP __ETHTOOL_LINK_MODE_LEGACY_MASK(TP) +#define SUPPORTED_AUI __ETHTOOL_LINK_MODE_LEGACY_MASK(AUI) +#define SUPPORTED_MII __ETHTOOL_LINK_MODE_LEGACY_MASK(MII) +#define SUPPORTED_FIBRE __ETHTOOL_LINK_MODE_LEGACY_MASK(FIBRE) +#define SUPPORTED_BNC __ETHTOOL_LINK_MODE_LEGACY_MASK(BNC) +#define SUPPORTED_10000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseT_Full) +#define SUPPORTED_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Pause) +#define SUPPORTED_Asym_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Asym_Pause) +#define SUPPORTED_2500baseX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(2500baseX_Full) +#define SUPPORTED_Backplane __ETHTOOL_LINK_MODE_LEGACY_MASK(Backplane) +#define SUPPORTED_1000baseKX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseKX_Full) +#define SUPPORTED_10000baseKX4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKX4_Full) +#define SUPPORTED_10000baseKR_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKR_Full) +#define SUPPORTED_10000baseR_FEC __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseR_FEC) +#define SUPPORTED_20000baseMLD2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseMLD2_Full) +#define SUPPORTED_20000baseKR2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseKR2_Full) +#define SUPPORTED_40000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseKR4_Full) +#define SUPPORTED_40000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseCR4_Full) +#define SUPPORTED_40000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseSR4_Full) +#define SUPPORTED_40000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseLR4_Full) +#define SUPPORTED_56000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseKR4_Full) +#define SUPPORTED_56000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseCR4_Full) +#define SUPPORTED_56000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseSR4_Full) +#define SUPPORTED_56000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseLR4_Full) +/* Please do not define any new SUPPORTED_* macro for bits > 31, see + * notice above. + */ + +/* + * DEPRECATED macros. Please migrate to + * ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. Please do NOT + * define any new ADERTISE_* macro for bits > 31. + */ +#define ADVERTISED_10baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Half) +#define ADVERTISED_10baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Full) +#define ADVERTISED_100baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Half) +#define ADVERTISED_100baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Full) +#define ADVERTISED_1000baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Half) +#define ADVERTISED_1000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Full) +#define ADVERTISED_Autoneg __ETHTOOL_LINK_MODE_LEGACY_MASK(Autoneg) +#define ADVERTISED_TP __ETHTOOL_LINK_MODE_LEGACY_MASK(TP) +#define ADVERTISED_AUI __ETHTOOL_LINK_MODE_LEGACY_MASK(AUI) +#define ADVERTISED_MII __ETHTOOL_LINK_MODE_LEGACY_MASK(MII) +#define ADVERTISED_FIBRE __ETHTOOL_LINK_MODE_LEGACY_MASK(FIBRE) +#define ADVERTISED_BNC __ETHTOOL_LINK_MODE_LEGACY_MASK(BNC) +#define ADVERTISED_10000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseT_Full) +#define ADVERTISED_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Pause) +#define ADVERTISED_Asym_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Asym_Pause) +#define ADVERTISED_2500baseX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(2500baseX_Full) +#define ADVERTISED_Backplane __ETHTOOL_LINK_MODE_LEGACY_MASK(Backplane) +#define ADVERTISED_1000baseKX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseKX_Full) +#define ADVERTISED_10000baseKX4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKX4_Full) +#define ADVERTISED_10000baseKR_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKR_Full) +#define ADVERTISED_10000baseR_FEC __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseR_FEC) +#define ADVERTISED_20000baseMLD2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseMLD2_Full) +#define ADVERTISED_20000baseKR2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseKR2_Full) +#define ADVERTISED_40000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseKR4_Full) +#define ADVERTISED_40000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseCR4_Full) +#define ADVERTISED_40000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseSR4_Full) +#define ADVERTISED_40000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseLR4_Full) +#define ADVERTISED_56000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseKR4_Full) +#define ADVERTISED_56000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseCR4_Full) +#define ADVERTISED_56000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseSR4_Full) +#define ADVERTISED_56000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseLR4_Full) +/* Please do not define any new ADVERTISED_* macro for bits > 31, see + * notice above. + */ /* The following are all involved in forcing a particular link * mode for the device for setting things. When getting the @@ -953,19 +1462,44 @@ enum ethtool_sfeatures_retval_bits { * it was forced up into this mode or autonegotiated. */ -/* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */ +/* The forced speed, in units of 1Mb. All values 0 to INT_MAX are legal. */ #define SPEED_10 10 #define SPEED_100 100 #define SPEED_1000 1000 #define SPEED_2500 2500 +#define SPEED_5000 5000 #define SPEED_10000 10000 +#define SPEED_20000 20000 +#define SPEED_25000 25000 +#define SPEED_40000 40000 +#define SPEED_50000 50000 +#define SPEED_56000 56000 +#define SPEED_100000 100000 + #define SPEED_UNKNOWN -1 +static inline int ethtool_validate_speed(__u32 speed) +{ + return speed <= INT_MAX || speed == SPEED_UNKNOWN; +} + /* Duplex, half or full. */ #define DUPLEX_HALF 0x00 #define DUPLEX_FULL 0x01 #define DUPLEX_UNKNOWN 0xff +static inline int ethtool_validate_duplex(__u8 duplex) +{ + switch (duplex) { + case DUPLEX_HALF: + case DUPLEX_FULL: + case DUPLEX_UNKNOWN: + return 1; + } + + return 0; +} + /* Which connector port. */ #define PORT_TP 0x00 #define PORT_AUI 0x01 @@ -977,22 +1511,23 @@ enum ethtool_sfeatures_retval_bits { #define PORT_OTHER 0xff /* Which transceiver to use. */ -#define XCVR_INTERNAL 0x00 -#define XCVR_EXTERNAL 0x01 +#define XCVR_INTERNAL 0x00 /* PHY and MAC are in the same package */ +#define XCVR_EXTERNAL 0x01 /* PHY and MAC are in different packages */ #define XCVR_DUMMY1 0x02 #define XCVR_DUMMY2 0x03 #define XCVR_DUMMY3 0x04 -/* Enable or disable autonegotiation. If this is set to enable, - * the forced link modes above are completely ignored. - */ +/* Enable or disable autonegotiation. */ #define AUTONEG_DISABLE 0x00 #define AUTONEG_ENABLE 0x01 -/* Mode MDI or MDI-X */ -#define ETH_TP_MDI_INVALID 0x00 -#define ETH_TP_MDI 0x01 -#define ETH_TP_MDI_X 0x02 +/* MDI or MDI-X status/control - if MDI/MDI_X/AUTO is set then + * the driver is required to renegotiate link + */ +#define ETH_TP_MDI_INVALID 0x00 /* status: unknown; control: unsupported */ +#define ETH_TP_MDI 0x01 /* status: MDI; control: force MDI */ +#define ETH_TP_MDI_X 0x02 /* status: MDI-X; control: force MDI-X */ +#define ETH_TP_MDI_AUTO 0x03 /* control: auto-select */ /* Wake-On-Lan options. */ #define WAKE_PHY (1 << 0) @@ -1008,20 +1543,23 @@ enum ethtool_sfeatures_retval_bits { #define UDP_V4_FLOW 0x02 /* hash or spec (udp_ip4_spec) */ #define SCTP_V4_FLOW 0x03 /* hash or spec (sctp_ip4_spec) */ #define AH_ESP_V4_FLOW 0x04 /* hash only */ -#define TCP_V6_FLOW 0x05 /* hash only */ -#define UDP_V6_FLOW 0x06 /* hash only */ -#define SCTP_V6_FLOW 0x07 /* hash only */ +#define TCP_V6_FLOW 0x05 /* hash or spec (tcp_ip6_spec; nfc only) */ +#define UDP_V6_FLOW 0x06 /* hash or spec (udp_ip6_spec; nfc only) */ +#define SCTP_V6_FLOW 0x07 /* hash or spec (sctp_ip6_spec; nfc only) */ #define AH_ESP_V6_FLOW 0x08 /* hash only */ #define AH_V4_FLOW 0x09 /* hash or spec (ah_ip4_spec) */ #define ESP_V4_FLOW 0x0a /* hash or spec (esp_ip4_spec) */ -#define AH_V6_FLOW 0x0b /* hash only */ -#define ESP_V6_FLOW 0x0c /* hash only */ -#define IP_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */ +#define AH_V6_FLOW 0x0b /* hash or spec (ah_ip6_spec; nfc only) */ +#define ESP_V6_FLOW 0x0c /* hash or spec (esp_ip6_spec; nfc only) */ +#define IPV4_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */ +#define IP_USER_FLOW IPV4_USER_FLOW +#define IPV6_USER_FLOW 0x0e /* spec only (usr_ip6_spec; nfc only) */ #define IPV4_FLOW 0x10 /* hash only */ #define IPV6_FLOW 0x11 /* hash only */ #define ETHER_FLOW 0x12 /* spec only (ether_spec) */ /* Flag to enable additional fields in struct ethtool_rx_flow_spec */ #define FLOW_EXT 0x80000000 +#define FLOW_MAC_EXT 0x40000000 /* L3-L4 network traffic flow hash options */ #define RXH_L2DA (1 << 1) @@ -1046,6 +1584,10 @@ enum ethtool_sfeatures_retval_bits { #define ETH_MODULE_SFF_8079_LEN 256 #define ETH_MODULE_SFF_8472 0x2 #define ETH_MODULE_SFF_8472_LEN 512 +#define ETH_MODULE_SFF_8636 0x3 +#define ETH_MODULE_SFF_8636_LEN 256 +#define ETH_MODULE_SFF_8436 0x4 +#define ETH_MODULE_SFF_8436_LEN 256 /* Reset flags */ /* The reset() operation must clear the flags for the components which @@ -1077,4 +1619,123 @@ enum ethtool_reset_flags { }; #define ETH_RESET_SHARED_SHIFT 16 -#endif /* _LINUX_ETHTOOL_H */ + +/** + * struct ethtool_link_settings - link control and status + * + * IMPORTANT, Backward compatibility notice: When implementing new + * user-space tools, please first try %ETHTOOL_GLINKSETTINGS, and + * if it succeeds use %ETHTOOL_SLINKSETTINGS to change link + * settings; do not use %ETHTOOL_SSET if %ETHTOOL_GLINKSETTINGS + * succeeded: stick to %ETHTOOL_GLINKSETTINGS/%SLINKSETTINGS in + * that case. Conversely, if %ETHTOOL_GLINKSETTINGS fails, use + * %ETHTOOL_GSET to query and %ETHTOOL_SSET to change link + * settings; do not use %ETHTOOL_SLINKSETTINGS if + * %ETHTOOL_GLINKSETTINGS failed: stick to + * %ETHTOOL_GSET/%ETHTOOL_SSET in that case. + * + * @cmd: Command number = %ETHTOOL_GLINKSETTINGS or %ETHTOOL_SLINKSETTINGS + * @speed: Link speed (Mbps) + * @duplex: Duplex mode; one of %DUPLEX_* + * @port: Physical connector type; one of %PORT_* + * @phy_address: MDIO address of PHY (transceiver); 0 or 255 if not + * applicable. For clause 45 PHYs this is the PRTAD. + * @autoneg: Enable/disable autonegotiation and auto-detection; + * either %AUTONEG_DISABLE or %AUTONEG_ENABLE + * @mdio_support: Bitmask of %ETH_MDIO_SUPPORTS_* flags for the MDIO + * protocols supported by the interface; 0 if unknown. + * Read-only. + * @eth_tp_mdix: Ethernet twisted-pair MDI(-X) status; one of + * %ETH_TP_MDI_*. If the status is unknown or not applicable, the + * value will be %ETH_TP_MDI_INVALID. Read-only. + * @eth_tp_mdix_ctrl: Ethernet twisted pair MDI(-X) control; one of + * %ETH_TP_MDI_*. If MDI(-X) control is not implemented, reads + * yield %ETH_TP_MDI_INVALID and writes may be ignored or rejected. + * When written successfully, the link should be renegotiated if + * necessary. + * @link_mode_masks_nwords: Number of 32-bit words for each of the + * supported, advertising, lp_advertising link mode bitmaps. For + * %ETHTOOL_GLINKSETTINGS: on entry, number of words passed by user + * (>= 0); on return, if handshake in progress, negative if + * request size unsupported by kernel: absolute value indicates + * kernel expected size and all the other fields but cmd + * are 0; otherwise (handshake completed), strictly positive + * to indicate size used by kernel and cmd field stays + * %ETHTOOL_GLINKSETTINGS, all other fields populated by driver. For + * %ETHTOOL_SLINKSETTINGS: must be valid on entry, ie. a positive + * value returned previously by %ETHTOOL_GLINKSETTINGS, otherwise + * refused. For drivers: ignore this field (use kernel's + * __ETHTOOL_LINK_MODE_MASK_NBITS instead), any change to it will + * be overwritten by kernel. + * @supported: Bitmap with each bit meaning given by + * %ethtool_link_mode_bit_indices for the link modes, physical + * connectors and other link features for which the interface + * supports autonegotiation or auto-detection. Read-only. + * @advertising: Bitmap with each bit meaning given by + * %ethtool_link_mode_bit_indices for the link modes, physical + * connectors and other link features that are advertised through + * autonegotiation or enabled for auto-detection. + * @lp_advertising: Bitmap with each bit meaning given by + * %ethtool_link_mode_bit_indices for the link modes, and other + * link features that the link partner advertised through + * autonegotiation; 0 if unknown or not applicable. Read-only. + * + * If autonegotiation is disabled, the speed and @duplex represent the + * fixed link mode and are writable if the driver supports multiple + * link modes. If it is enabled then they are read-only; if the link + * is up they represent the negotiated link mode; if the link is down, + * the speed is 0, %SPEED_UNKNOWN or the highest enabled speed and + * @duplex is %DUPLEX_UNKNOWN or the best enabled duplex mode. + * + * Some hardware interfaces may have multiple PHYs and/or physical + * connectors fitted or do not allow the driver to detect which are + * fitted. For these interfaces @port and/or @phy_address may be + * writable, possibly dependent on @autoneg being %AUTONEG_DISABLE. + * Otherwise, attempts to write different values may be ignored or + * rejected. + * + * Deprecated %ethtool_cmd fields transceiver, maxtxpkt and maxrxpkt + * are not available in %ethtool_link_settings. Until all drivers are + * converted to ignore them or to the new %ethtool_link_settings API, + * for both queries and changes, users should always try + * %ETHTOOL_GLINKSETTINGS first, and if it fails with -ENOTSUPP stick + * only to %ETHTOOL_GSET and %ETHTOOL_SSET consistently. If it + * succeeds, then users should stick to %ETHTOOL_GLINKSETTINGS and + * %ETHTOOL_SLINKSETTINGS (which would support drivers implementing + * either %ethtool_cmd or %ethtool_link_settings). + * + * Users should assume that all fields not marked read-only are + * writable and subject to validation by the driver. They should use + * %ETHTOOL_GLINKSETTINGS to get the current values before making specific + * changes and then applying them with %ETHTOOL_SLINKSETTINGS. + * + * Drivers that implement %get_link_ksettings and/or + * %set_link_ksettings should ignore the @cmd + * and @link_mode_masks_nwords fields (any change to them overwritten + * by kernel), and rely only on kernel's internal + * %__ETHTOOL_LINK_MODE_MASK_NBITS and + * %ethtool_link_mode_mask_t. Drivers that implement + * %set_link_ksettings() should validate all fields other than @cmd + * and @link_mode_masks_nwords that are not described as read-only or + * deprecated, and must ignore all fields described as read-only. + */ +struct ethtool_link_settings { + __u32 cmd; + __u32 speed; + __u8 duplex; + __u8 port; + __u8 phy_address; + __u8 autoneg; + __u8 mdio_support; + __u8 eth_tp_mdix; + __u8 eth_tp_mdix_ctrl; + __s8 link_mode_masks_nwords; + __u32 reserved[8]; + __u32 link_mode_masks[0]; + /* layout of link_mode_masks fields: + * __u32 map_supported[link_mode_masks_nwords]; + * __u32 map_advertising[link_mode_masks_nwords]; + * __u32 map_lp_advertising[link_mode_masks_nwords]; + */ +}; +#endif /* _UAPI_LINUX_ETHTOOL_H */