From: Russell King (Oracle) Date: Thu, 1 May 2025 11:45:01 +0000 (+0100) Subject: net: stmmac: use a local variable for priv->phylink_config X-Git-Tag: v6.16-rc1~132^2~177^2~5 X-Git-Url: http://git.ipfire.org/?a=commitdiff_plain;h=5ad39ceaea00e3606491fdec9f68722811330577;p=thirdparty%2Flinux.git net: stmmac: use a local variable for priv->phylink_config Use a local variable for priv->phylink_config in stmmac_phy_setup() which makes the code a bit easier to read, allowing some lines to be merged. Signed-off-by: Russell King (Oracle) Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/E1uASLd-0021QR-Cu@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski --- diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index f59a2363f1506..fe7f9e3a92a56 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -1259,19 +1259,22 @@ static int stmmac_phy_setup(struct stmmac_priv *priv) { struct stmmac_mdio_bus_data *mdio_bus_data; int mode = priv->plat->phy_interface; + struct phylink_config *config; struct fwnode_handle *fwnode; struct phylink_pcs *pcs; struct phylink *phylink; - priv->phylink_config.dev = &priv->dev->dev; - priv->phylink_config.type = PHYLINK_NETDEV; - priv->phylink_config.mac_managed_pm = true; + config = &priv->phylink_config; + + config->dev = &priv->dev->dev; + config->type = PHYLINK_NETDEV; + config->mac_managed_pm = true; /* Stmmac always requires an RX clock for hardware initialization */ - priv->phylink_config.mac_requires_rxc = true; + config->mac_requires_rxc = true; if (!(priv->plat->flags & STMMAC_FLAG_RX_CLK_RUNS_IN_LPI)) - priv->phylink_config.eee_rx_clk_stop_enable = true; + config->eee_rx_clk_stop_enable = true; /* Set the default transmit clock stop bit based on the platform glue */ priv->tx_lpi_clk_stop = priv->plat->flags & @@ -1279,13 +1282,12 @@ static int stmmac_phy_setup(struct stmmac_priv *priv) mdio_bus_data = priv->plat->mdio_bus_data; if (mdio_bus_data) - priv->phylink_config.default_an_inband = - mdio_bus_data->default_an_inband; + config->default_an_inband = mdio_bus_data->default_an_inband; /* Set the platform/firmware specified interface mode. Note, phylink * deals with the PHY interface mode, not the MAC interface mode. */ - __set_bit(mode, priv->phylink_config.supported_interfaces); + __set_bit(mode, config->supported_interfaces); /* If we have an xpcs, it defines which PHY interfaces are supported. */ if (priv->hw->xpcs) @@ -1294,29 +1296,26 @@ static int stmmac_phy_setup(struct stmmac_priv *priv) pcs = priv->hw->phylink_pcs; if (pcs) - phy_interface_or(priv->phylink_config.supported_interfaces, - priv->phylink_config.supported_interfaces, + phy_interface_or(config->supported_interfaces, + config->supported_interfaces, pcs->supported_interfaces); if (priv->dma_cap.eee) { /* Assume all supported interfaces also support LPI */ - memcpy(priv->phylink_config.lpi_interfaces, - priv->phylink_config.supported_interfaces, - sizeof(priv->phylink_config.lpi_interfaces)); + memcpy(config->lpi_interfaces, config->supported_interfaces, + sizeof(config->lpi_interfaces)); /* All full duplex speeds above 100Mbps are supported */ - priv->phylink_config.lpi_capabilities = ~(MAC_1000FD - 1) | - MAC_100FD; - priv->phylink_config.lpi_timer_default = eee_timer * 1000; - priv->phylink_config.eee_enabled_default = true; + config->lpi_capabilities = ~(MAC_1000FD - 1) | MAC_100FD; + config->lpi_timer_default = eee_timer * 1000; + config->eee_enabled_default = true; } fwnode = priv->plat->port_node; if (!fwnode) fwnode = dev_fwnode(priv->device); - phylink = phylink_create(&priv->phylink_config, fwnode, - mode, &stmmac_phylink_mac_ops); + phylink = phylink_create(config, fwnode, mode, &stmmac_phylink_mac_ops); if (IS_ERR(phylink)) return PTR_ERR(phylink);