From: Imre Deak Date: Tue, 8 Jul 2025 21:23:31 +0000 (+0300) Subject: drm/dp: Change AUX DPCD probe address from LANE0_1_STATUS to TRAINING_PATTERN_SET X-Git-Tag: v6.16-rc7~29^2~3^2 X-Git-Url: http://git.ipfire.org/?a=commitdiff_plain;h=d34d6feaf4a76833effcec0b148b65946b04cde8;p=thirdparty%2Flinux.git drm/dp: Change AUX DPCD probe address from LANE0_1_STATUS to TRAINING_PATTERN_SET Commit a3ef3c2da675 ("drm/dp: Change AUX DPCD probe address from DPCD_REV to LANE0_1_STATUS") stopped using the DPCD_REV register for DPCD probing, since this results in link training failures at least when using an Intel Barlow Ridge TBT hub at UHBR link rates (the DP_INTRA_HOP_AUX_REPLY_INDICATION never getting cleared after the failed link training). Since accessing DPCD_REV during link training is prohibited by the DP Standard, LANE0_1_STATUS (0x202) was used instead, as it falls within the Standard's valid register address range (0x102-0x106, 0x202-0x207, 0x200c-0x200f, 0x2216) and it fixed the link training on the above TBT hub. However, reading the LANE0_1_STATUS register also has a side-effect at least on a Novatek eDP panel, as reported on the Closes: link below, resulting in screen flickering on that panel. One clear side-effect when doing the 1-byte probe reads from LANE0_1_STATUS during link training before reading out the full 6 byte link status starting at the same address is that the panel will report the link training as completed with voltage swing 0. This is different from the normal, flicker-free scenario when no DPCD probing is done, the panel reporting the link training complete with voltage swing 2. Using the TRAINING_PATTERN_SET register for DPCD probing doesn't have the above side-effect, the panel will link train with voltage swing 2 as expected and it will stay flicker-free. This register is also in the above valid register range and is unlikely to have a side-effect as that of LANE0_1_STATUS: Reading LANE0_1_STATUS is part of the link training CR/EQ sequences and so it may cause a state change in the sink - even if inadvertently as I suspect in the case of the above Novatek panel. As opposed to this, reading TRAINING_PATTERN_SET is not part of the link training sequence (it must be only written once at the beginning of the CR/EQ sequences), so it's unlikely to cause any state change in the sink. As a side-note, this Novatek panel also lacks support for TPS3, while claiming support for HBR2, which violates the DP Standard (the Standard mandating TPS3 for HBR2). Besides the Novatek panel (PSR 1), which this change fixes, I also verified the change on a Samsung (PSR 1) and an Analogix (PSR 2) eDP panel as well as on the Intel Barlow Ridge TBT hub. Note that in the drm-tip tree (targeting the v6.17 kernel version) the i915 and xe drivers keep DPCD probing enabled only for the panel known to require this (HP ZR24w), hence those drivers in drm-tip are not affected by the above problem. Cc: Ville Syrjälä Cc: Jani Nikula Fixes: a3ef3c2da675 ("drm/dp: Change AUX DPCD probe address from DPCD_REV to LANE0_1_STATUS") Reported-and-tested-by: Paul Menzel Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14558 Reviewed-by: Jonathan Cavitt Acked-by: Thomas Zimmermann Link: https://lore.kernel.org/r/20250708212331.112898-1-imre.deak@intel.com (cherry picked from commit bba9aa41654036534d86b198f5647a9ce15ebd7f) [Imre: Rebased on drm-intel-fixes] Signed-off-by: Imre Deak Signed-off-by: Rodrigo Vivi [Rodrigo: Changed original commit hash to match with the one propagated in fixes] --- diff --git a/drivers/gpu/drm/display/drm_dp_helper.c b/drivers/gpu/drm/display/drm_dp_helper.c index dc622c78db9d..ea78c6c8ca7a 100644 --- a/drivers/gpu/drm/display/drm_dp_helper.c +++ b/drivers/gpu/drm/display/drm_dp_helper.c @@ -725,7 +725,7 @@ ssize_t drm_dp_dpcd_read(struct drm_dp_aux *aux, unsigned int offset, * monitor doesn't power down exactly after the throw away read. */ if (!aux->is_remote) { - ret = drm_dp_dpcd_probe(aux, DP_LANE0_1_STATUS); + ret = drm_dp_dpcd_probe(aux, DP_TRAINING_PATTERN_SET); if (ret < 0) return ret; }