From: Josua Mayer Date: Sun, 24 May 2026 14:54:48 +0000 (+0200) Subject: arm64: dts: Add support for LX2160 Twins board in single configuration X-Git-Url: http://git.ipfire.org/?a=commitdiff_plain;h=df70a90b032f641643312aaf32442a2018b4bc3d;p=thirdparty%2Flinux.git arm64: dts: Add support for LX2160 Twins board in single configuration Add support for the SolidRun LX2160A Twins board in its single cpu configuration. The twins board is designed to host a pair of LX2160A CEX-7 modules, sharing a single PCI-E connector in multi-host mode. It may be assembled in two configurations (different assembly options facilitating signal re-routing), with a single or with dual CEX-7 module. Their marketing names are: - SolidWAN Single LX2160 - SolidWAN Dual LX2160 Add the single configuration, featuring: - 8x SFP (1Gbps) - 8x SFP+ (1/10Gbps) - PCI-E OCP card connector - USB-3.0 front-panel header with single port - microSD - dual hot-swappable power supplies Signed-off-by: Josua Mayer Signed-off-by: Frank Li --- diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 049eebda314d..aaebad5e6427 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -51,6 +51,8 @@ DTC_FLAGS_fsl-lx2160a-bluebox3-rev-a := -Wno-interrupt_map dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb DTC_FLAGS_fsl-lx2160a-clearfog-cx := -Wno-interrupt_map dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb +DTC_FLAGS_fsl-lx2160a-half-twins := -Wno-interrupt_map +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-half-twins.dtb DTC_FLAGS_fsl-lx2160a-honeycomb := -Wno-interrupt_map dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb DTC_FLAGS_fsl-lx2160a-qds := -Wno-interrupt_map diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi index 2c86734c39ab..16caa281ece0 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi @@ -65,7 +65,7 @@ #size-cells = <0>; reg = <0x77>; - i2c@0 { + ddr_i2c: i2c@0 { #address-cells = <1>; #size-cells = <0>; reg = <0>; @@ -91,7 +91,7 @@ }; }; - i2c@1 { + fan_i2c: i2c@1 { #address-cells = <1>; #size-cells = <0>; reg = <1>; @@ -102,7 +102,7 @@ }; }; - i2c@2 { + power_i2c: i2c@2 { #address-cells = <1>; #size-cells = <0>; reg = <2>; @@ -113,7 +113,7 @@ }; }; - i2c@3 { + i2c_smb: i2c@3 { #address-cells = <1>; #size-cells = <0>; reg = <3>; diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-half-twins.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-half-twins.dts new file mode 100644 index 000000000000..d16e27307275 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-half-twins.dts @@ -0,0 +1,830 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +// +// Device Tree file for single LX2160A CEX-7 on Twins board. +// +// Copyright 2022 SolidRun Ltd. + +/dts-v1/; + +#include + +#include "fsl-lx2160a-rev2.dtsi" +#include "fsl-lx2160a-cex7.dtsi" + +/ { + compatible = "solidrun,twins-single", "solidrun,lx2160a-cex7", "fsl,lx2160a"; + model = "SolidRun LX2160A SolidWAN Single"; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + gpio4 = &expander0; + gpio5 = &expander1; + gpio6 = &expander2; + gpio7 = &expander3; + i2c0 = &i2c0; + i2c1 = &i2c2; + i2c2 = &i2c4; + i2c3 = &fan_i2c; + i2c4 = &power_i2c; + i2c5 = &i2c_smb; + i2c6 = &sfp0_i2c; + i2c7 = &sfp1_i2c; + i2c8 = &sfp2_i2c; + i2c9 = &sfp3_i2c; + i2c10 = &twins_sfp_c1_at_i2c; + i2c11 = &twins_sfp_c1_ab_i2c; + i2c12 = &twins_sfp_c1_bt_i2c; + i2c13 = &twins_sfp_c1_bb_i2c; + i2c14 = &twins_sfp_c2_at_i2c; + i2c15 = &twins_sfp_c2_ab_i2c; + i2c16 = &twins_sfp_c2_bt_i2c; + i2c17 = &twins_sfp_c2_bb_i2c; + i2c18 = &twins_sfp_c3_at_i2c; + i2c19 = &twins_sfp_c3_ab_i2c; + i2c20 = &twins_sfp_c3_bt_i2c; + i2c21 = &twins_sfp_c3_bb_i2c; + i2c22 = &htwins_sfp_c3_at_i2c; + i2c23 = &htwins_sfp_c3_ab_i2c; + i2c24 = &htwins_sfp_c3_bt_i2c; + i2c25 = &htwins_sfp_c3_bb_i2c; + i2c26 = &ddr_i2c; + mmc0 = &esdhc0; + mmc1 = &esdhc1; + serial0 = &uart0; + serial1 = &uart1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led_ht_c3_bt: led-sfp-1 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + gpios = <&expander3 14 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac5>; + linux,default-trigger = "netdev"; + }; + + led_ht_c3_bb: led-sfp-2 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + gpios = <&expander3 13 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac15>; + linux,default-trigger = "netdev"; + }; + + led_ht_c3_at: led-sfp-3 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <3>; + gpios = <&expander3 11 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac6>; + linux,default-trigger = "netdev"; + }; + + led_ht_c3_ab: led-sfp-4 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <4>; + gpios = <&expander3 12 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac11>; + linux,default-trigger = "netdev"; + }; + + led_c1_bt: led-sfp-9 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <9>; + gpios = <&expander1 4 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac4>; + linux,default-trigger = "netdev"; + }; + + led_c1_bb: led-sfp-10 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <10>; + gpios = <&expander1 3 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac17>; + linux,default-trigger = "netdev"; + }; + + led_c1_at: led-sfp-11 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <11>; + gpios = <&expander1 1 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac3>; + linux,default-trigger = "netdev"; + }; + + led_c1_ab: led-sfp-12 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <12>; + gpios = <&expander1 2 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac12>; + linux,default-trigger = "netdev"; + }; + + led_c2_bt: led-sfp-13 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <13>; + gpios = <&expander1 10 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac8>; + linux,default-trigger = "netdev"; + }; + + led_c2_bb: led-sfp-14 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <14>; + gpios = <&expander1 9 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac16>; + linux,default-trigger = "netdev"; + }; + + led_c2_at: led-sfp-15 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <15>; + gpios = <&expander1 5 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac7>; + linux,default-trigger = "netdev"; + }; + + led_c2_ab: led-sfp-16 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <16>; + gpios = <&expander1 6 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac18>; + linux,default-trigger = "netdev"; + }; + + led_c3_bt: led-sfp-17 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <17>; + gpios = <&expander1 14 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac10>; + linux,default-trigger = "netdev"; + }; + + led_c3_bb: led-sfp-18 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <18>; + gpios = <&expander1 13 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac14>; + linux,default-trigger = "netdev"; + }; + + led_c3_at: led-sfp-19 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <19>; + gpios = <&expander1 11 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac9>; + linux,default-trigger = "netdev"; + }; + + led_c3_ab: led-sfp-20 { + color = ; + default-state = "off"; + function = LED_FUNCTION_LAN; + function-enumerator = <20>; + gpios = <&expander1 12 GPIO_ACTIVE_LOW>; + trigger-sources = <&dpmac13>; + linux,default-trigger = "netdev"; + }; + + led-status { + color = ; + default-state = "off"; + function = LED_FUNCTION_STATUS; + function-enumerator = <0>; + gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + + led-status-twin { + color = ; + default-state = "off"; + function = LED_FUNCTION_STATUS; + function-enumerator = <1>; + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; + }; + + led-fault { + color = ; + default-state = "off"; + function = LED_FUNCTION_FAULT; + function-enumerator = <0>; + gpios = <&gpio2 11 GPIO_ACTIVE_LOW>; + panic-indicator; + }; + + led-fault-twin { + color = ; + default-state = "off"; + function = LED_FUNCTION_FAULT; + function-enumerator = <1>; + gpios = <&gpio2 9 GPIO_ACTIVE_LOW>; + }; + }; + + mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + /* + * This gpio controlled mux can route the tacho signals of 6 PWM FAN connectors + * to the tacho inputs of both CEX-7 modules (twins). + * + * The first twin controls this mux and monitors four fan connectors, two intended + * for itself, and two for the OCP card. + * + * The second twin monitors only two fan connectors intended for itself. + * + * The table below maps selector GPIO states to monitored fan connector per twin: + * + * | SEL1 | SEL0 | Twin 1 | Twin 2 | + * | ---: | ---: | :------| ------ | + * | 0 | 0 | J10 | J5024 | + * | 0 | 1 | J5016 | J5024 | + * | 1 | 0 | J5026 | J5025 | + * | 1 | 1 | J5013 | J5025 | + */ + mux-gpios = <&expander0 8 GPIO_ACTIVE_HIGH>, /* SEL0 */ + <&expander0 15 GPIO_ACTIVE_HIGH>; /* SEL1 */ + }; + + ht_c3_bt_sfp: sfp-1 { + compatible = "sff,sfp"; + i2c-bus = <&htwins_sfp_c3_bt_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander2 13 GPIO_ACTIVE_LOW>; + }; + + ht_c3_bb_sfp: sfp-2 { + compatible = "sff,sfp"; + i2c-bus = <&htwins_sfp_c3_bb_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander2 14 GPIO_ACTIVE_LOW>; + }; + + ht_c3_at_sfp: sfp-3 { + compatible = "sff,sfp"; + i2c-bus = <&htwins_sfp_c3_at_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander2 11 GPIO_ACTIVE_LOW>; + }; + + ht_c3_ab_sfp: sfp-4 { + compatible = "sff,sfp"; + i2c-bus = <&htwins_sfp_c3_ab_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander2 12 GPIO_ACTIVE_LOW>; + }; + + c1_bt_sfp: sfp-9 { + compatible = "sff,sfp"; + i2c-bus = <&twins_sfp_c1_bt_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander0 3 GPIO_ACTIVE_LOW>; + }; + + c1_bb_sfp: sfp-10 { + compatible = "sff,sfp"; + i2c-bus = <&twins_sfp_c1_bb_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander0 4 GPIO_ACTIVE_LOW>; + }; + + c1_at_sfp: sfp-11 { + compatible = "sff,sfp"; + i2c-bus = <&twins_sfp_c1_at_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander0 1 GPIO_ACTIVE_LOW>; + }; + + c1_ab_sfp: sfp-12 { + compatible = "sff,sfp"; + i2c-bus = <&twins_sfp_c1_ab_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander0 2 GPIO_ACTIVE_LOW>; + }; + + c2_bt_sfp: sfp-13 { + compatible = "sff,sfp"; + i2c-bus = <&twins_sfp_c2_bt_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander0 9 GPIO_ACTIVE_LOW>; + }; + + c2_bb_sfp: sfp-14 { + compatible = "sff,sfp"; + i2c-bus = <&twins_sfp_c2_bb_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander0 10 GPIO_ACTIVE_LOW>; + }; + + c2_at_sfp: sfp-15 { + compatible = "sff,sfp"; + i2c-bus = <&twins_sfp_c2_at_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander0 5 GPIO_ACTIVE_LOW>; + }; + + c2_ab_sfp: sfp-16 { + compatible = "sff,sfp"; + i2c-bus = <&twins_sfp_c2_ab_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander0 6 GPIO_ACTIVE_LOW>; + }; + + c3_bt_sfp: sfp-17 { + compatible = "sff,sfp"; + i2c-bus = <&twins_sfp_c3_bt_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander0 13 GPIO_ACTIVE_LOW>; + }; + + c3_bb_sfp: sfp-18 { + compatible = "sff,sfp"; + i2c-bus = <&twins_sfp_c3_bb_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander0 14 GPIO_ACTIVE_LOW>; + }; + + c3_at_sfp: sfp-19 { + compatible = "sff,sfp"; + i2c-bus = <&twins_sfp_c3_at_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander0 11 GPIO_ACTIVE_LOW>; + }; + + c3_ab_sfp: sfp-20 { + compatible = "sff,sfp"; + i2c-bus = <&twins_sfp_c3_ab_i2c>; + maximum-power-milliwatt = <2000>; + mod-def0-gpios = <&expander0 12 GPIO_ACTIVE_LOW>; + }; +}; + +/* + * This board supports industrial grade temperatures, + * the LX2160A SoC maximum junction temperature is 105°C. + * + * Raise thermal thresholds to allow operation near maximum temperature. + */ +&ccn_dpaa_alert { + temperature = <100000>; +}; + +&ccn_dpaa_crit { + temperature = <105000>; +}; + +&cluster2_3_alert { + temperature = <100000>; +}; + +&cluster2_3_crit { + temperature = <105000>; +}; + +&cluster4_alert { + temperature = <100000>; +}; + +&cluster4_crit { + temperature = <105000>; +}; + +&cluster5_alert { + temperature = <100000>; +}; + +&cluster5_crit { + temperature = <105000>; +}; + +&cluster6_7_alert { + temperature = <100000>; +}; + +&cluster6_7_crit { + temperature = <105000>; +}; + +&dce_qbman_alert { + temperature = <100000>; +}; + +&dce_qbman_crit { + temperature = <105000>; +}; + +/* sfp port 11 */ +&dpmac3 { + managed = "in-band-status"; + phys = <&serdes_1 7>; + sfp = <&c1_at_sfp>; +}; + +/* sfp port 9 */ +&dpmac4 { + managed = "in-band-status"; + phys = <&serdes_1 6>; + sfp = <&c1_bt_sfp>; +}; + +/* sfp port 1 */ +&dpmac5 { + managed = "in-band-status"; + phys = <&serdes_1 5>; + sfp = <&ht_c3_bt_sfp>; +}; + +/* sfp port 3 */ +&dpmac6 { + managed = "in-band-status"; + phys = <&serdes_1 4>; + sfp = <&ht_c3_at_sfp>; +}; + +/* sfp port 15 */ +&dpmac7 { + managed = "in-band-status"; + phys = <&serdes_1 3>; + sfp = <&c2_at_sfp>; +}; + +/* sfp port 13 */ +&dpmac8 { + managed = "in-band-status"; + phys = <&serdes_1 2>; + sfp = <&c2_bt_sfp>; +}; + +/* sfp port 19 */ +&dpmac9 { + managed = "in-band-status"; + phys = <&serdes_1 1>; + sfp = <&c3_at_sfp>; +}; + +/* sfp port 17 */ +&dpmac10 { + managed = "in-band-status"; + phys = <&serdes_1 0>; + sfp = <&c3_bt_sfp>; +}; + +/* sfp port 4 */ +&dpmac11 { + managed = "in-band-status"; + phys = <&serdes_2 0>; + sfp = <&ht_c3_ab_sfp>; +}; + +/* sfp port 12 */ +&dpmac12 { + managed = "in-band-status"; + phys = <&serdes_2 1>; + sfp = <&c1_ab_sfp>; +}; + +/* sfp port 20 */ +&dpmac13 { + managed = "in-band-status"; + phys = <&serdes_2 6>; + sfp = <&c3_ab_sfp>; +}; + +/* sfp port 18 */ +&dpmac14 { + managed = "in-band-status"; + phys = <&serdes_2 7>; + sfp = <&c3_bb_sfp>; +}; + +/* sfp port 2 */ +&dpmac15 { + managed = "in-band-status"; + phys = <&serdes_2 4>; + sfp = <&ht_c3_bb_sfp>; +}; + +/* sfp port 14 */ +&dpmac16 { + managed = "in-band-status"; + phys = <&serdes_2 5>; + sfp = <&c2_bb_sfp>; +}; + +/* sfp port 10 */ +&dpmac17 { + /* override connection to on-COM phy */ + /delete-property/ phy-handle; + /delete-property/ phy-connection-type; + managed = "in-band-status"; + phys = <&serdes_2 2>; + sfp = <&c1_bb_sfp>; +}; + +/* sfp port 16 */ +&dpmac18 { + managed = "in-band-status"; + phys = <&serdes_2 3>; + sfp = <&c2_ab_sfp>; +}; + +&esdhc0 { + pinctrl-0 = <&esdhc0_cd_wp_pins>, <&esdhc0_cmd_data30_clk_vsel_pins>; + pinctrl-names = "default"; + /* + * Disable 1.8V modes so that microsd state is same between + * power-on-reset, u-boot and linux. + * This avoids sporadic read errors after hard reset with some cards. + */ + no-1-8-v; + status = "okay"; +}; + +&i2c2 { + expander0: gpio@20 { + compatible = "nxp,pca9555"; + reg = <0x20>; + #gpio-cells = <2>; + gpio-controller; + }; + + expander1: gpio@21 { + compatible = "nxp,pca9555"; + reg = <0x21>; + #gpio-cells = <2>; + gpio-controller; + }; + + expander2: gpio@24 { + compatible = "nxp,pca9555"; + reg = <0x24>; + #gpio-cells = <2>; + gpio-controller; + }; + + expander3: gpio@25 { + compatible = "nxp,pca9555"; + reg = <0x25>; + #gpio-cells = <2>; + gpio-controller; + }; + + /* Half twins configuration; take over c3 from the other twin side */ + i2c-mux@73 { + compatible = "nxp,pca9547"; + reg = <0x73>; + #address-cells = <1>; + #size-cells = <0>; + i2c-mux-idle-disconnect; + + htwins_sfp_c3_at_i2c: i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + }; + + htwins_sfp_c3_ab_i2c: i2c@4 { + reg = <4>; + #address-cells = <1>; + #size-cells = <0>; + }; + + htwins_sfp_c3_bt_i2c: i2c@5 { + reg = <5>; + #address-cells = <1>; + #size-cells = <0>; + }; + + htwins_sfp_c3_bb_i2c: i2c@6 { + reg = <6>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + i2c-mux@76 { + compatible = "nxp,pca9547"; + reg = <0x76>; + #address-cells = <1>; + #size-cells = <0>; + i2c-mux-idle-disconnect; + + twins_sfp_c1_at_i2c: i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + twins_sfp_c1_ab_i2c: i2c@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + twins_sfp_c1_bt_i2c: i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + }; + + twins_sfp_c1_bb_i2c: i2c@4 { + reg = <4>; + #address-cells = <1>; + #size-cells = <0>; + }; + + twins_sfp_c2_at_i2c: i2c@5 { + reg = <5>; + #address-cells = <1>; + #size-cells = <0>; + }; + + twins_sfp_c2_ab_i2c: i2c@6 { + reg = <6>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + i2c-mux@77 { + compatible = "nxp,pca9547"; + reg = <0x77>; + #address-cells = <1>; + #size-cells = <0>; + i2c-mux-idle-disconnect; + + twins_sfp_c2_bt_i2c: i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + twins_sfp_c2_bb_i2c: i2c@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + twins_sfp_c3_at_i2c: i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + }; + + twins_sfp_c3_ab_i2c: i2c@4 { + reg = <4>; + #address-cells = <1>; + #size-cells = <0>; + }; + + twins_sfp_c3_bt_i2c: i2c@5 { + reg = <5>; + #address-cells = <1>; + #size-cells = <0>; + }; + + twins_sfp_c3_bb_i2c: i2c@6 { + reg = <6>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; +}; + +&pcie5 { + status = "okay"; +}; + +&pcs_mdio3 { + status = "okay"; +}; + +&pcs_mdio4 { + status = "okay"; +}; + +&pcs_mdio5 { + status = "okay"; +}; + +&pcs_mdio6 { + status = "okay"; +}; + +&pcs_mdio7 { + status = "okay"; +}; + +&pcs_mdio8 { + status = "okay"; +}; + +&pcs_mdio9 { + status = "okay"; +}; + +&pcs_mdio10 { + status = "okay"; +}; + +&pcs_mdio11 { + status = "okay"; +}; + +&pcs_mdio12 { + status = "okay"; +}; + +&pcs_mdio13 { + status = "okay"; +}; + +&pcs_mdio14 { + status = "okay"; +}; + +&pcs_mdio15 { + status = "okay"; +}; + +&pcs_mdio16 { + status = "okay"; +}; + +&pcs_mdio17 { + status = "okay"; +}; + +&pcs_mdio18 { + status = "okay"; +}; + +&rgmii_phy1 { + /* + * COM has a phy at address 1 connected to SoC Ethernet Controller 1. + * It competes for WRIOP MAC17, and no connector has been wired. + */ + status = "disabled"; +}; + +&serdes_2 { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&wriop_alert { + temperature = <100000>; +}; + +&wriop_crit { + temperature = <105000>; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi index 479982948ee5..1d73abffa6b7 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi @@ -499,13 +499,13 @@ thermal-sensors = <&tmu 1>; trips { - ddr-cluster5-alert { + cluster5_alert: ddr-cluster5-alert { temperature = <85000>; hysteresis = <2000>; type = "passive"; }; - ddr-cluster5-crit { + cluster5_crit: ddr-cluster5-crit { temperature = <95000>; hysteresis = <2000>; type = "critical"; @@ -519,13 +519,13 @@ thermal-sensors = <&tmu 2>; trips { - wriop-alert { + wriop_alert: wriop-alert { temperature = <85000>; hysteresis = <2000>; type = "passive"; }; - wriop-crit { + wriop_crit: wriop-crit { temperature = <95000>; hysteresis = <2000>; type = "critical"; @@ -539,13 +539,13 @@ thermal-sensors = <&tmu 3>; trips { - dce-qbman-alert { + dce_qbman_alert: dce-qbman-alert { temperature = <85000>; hysteresis = <2000>; type = "passive"; }; - dce-qbman-crit { + dce_qbman_crit: dce-qbman-crit { temperature = <95000>; hysteresis = <2000>; type = "critical"; @@ -559,13 +559,13 @@ thermal-sensors = <&tmu 4>; trips { - ccn-dpaa-alert { + ccn_dpaa_alert: ccn-dpaa-alert { temperature = <85000>; hysteresis = <2000>; type = "passive"; }; - ccn-dpaa-crit { + ccn_dpaa_crit: ccn-dpaa-crit { temperature = <95000>; hysteresis = <2000>; type = "critical"; @@ -579,13 +579,13 @@ thermal-sensors = <&tmu 5>; trips { - clust4-hsio3-alert { + cluster4_alert: clust4-hsio3-alert { temperature = <85000>; hysteresis = <2000>; type = "passive"; }; - clust4-hsio3-crit { + cluster4_crit: clust4-hsio3-crit { temperature = <95000>; hysteresis = <2000>; type = "critical"; @@ -599,13 +599,13 @@ thermal-sensors = <&tmu 6>; trips { - cluster2-3-alert { + cluster2_3_alert: cluster2-3-alert { temperature = <85000>; hysteresis = <2000>; type = "passive"; }; - cluster2-3-crit { + cluster2_3_crit: cluster2-3-crit { temperature = <95000>; hysteresis = <2000>; type = "critical";