From: Rhnn Hur Date: Sun, 20 Oct 2024 11:14:28 +0000 (+0900) Subject: mediatek: filogic: add support for ipTIME AX3000M X-Git-Url: http://git.ipfire.org/?a=commitdiff_plain;h=refs%2Fpull%2F16643%2Fhead;p=thirdparty%2Fopenwrt.git mediatek: filogic: add support for ipTIME AX3000M ipTIME AX3000M is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7981B. (Filogic 820) Specifications: * SoC: MetiaTek MT7981B * RAM: 256MiB * Flash: ESMT SPI-NAND F50L1G41LB 128MiB * Wi-Fi: * MediaTek MT7915E: 2.4GHz and 5GHz * Ethernet: 5x 1GbE * Switch: MediaTek MT7531 * USB: 1x 3.0 * UART: J4 (115200 baud) * LED: * PWR: VCC * CPU, 2.4G, 5G: GPIO * LAN 1-4, WAN: Controlled by Switch MAC Addresses: * 2.4G, 5G: B0:XX:XX:04:2A:60 (factory 0x4) * WAN: B0:XX:XX:04:2A:61 (factory 0x4, +1) * LAN: B0:XX:XX:04:2A:63 (factory 0x4, +3) MTD Partitions: * 0x000000000000-0x000000100000 : "BL2" * 0x000000100000-0x000000180000 : "u-boot-env" * 0x000000180000-0x000000380000 : "Factory" * 0x000000380000-0x000000580000 : "FIP" * 0x000000580000-0x000007380000 : "ubi" UBI Partitions (Dynamic): * id: 0, kernel2 * id: 1, kernel * id: 2, rootfs * id: 3, rootfs_data * id: 4, rootfs2 Installation: * Upload factory image through the tftp recovery mode. Notes: * This device has a dual-boot partition scheme, if installing with the stock web interface method will flash only on the inactive ubi partitions which are kernel and rootfs, newly flashed kernel didn't know the proper rootfs partition so the booted kernel will panic. Tested-by: Rhnn Hur Signed-off-by: Rhnn Hur Link: https://github.com/openwrt/openwrt/pull/16643 Signed-off-by: Hauke Mehrtens --- diff --git a/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic index d07a3d1dcff..0a5c6004de9 100644 --- a/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic @@ -81,7 +81,8 @@ jdcloud,re-cp-03) ;; esac ;; -comfast,cf-e393ax) +comfast,cf-e393ax|\ +iptime,ax3000m) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x80000" ;; cetron,ct3003|\ diff --git a/target/linux/mediatek/dts/mt7981b-iptime-ax3000m.dts b/target/linux/mediatek/dts/mt7981b-iptime-ax3000m.dts new file mode 100644 index 00000000000..a893fc3dc79 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-iptime-ax3000m.dts @@ -0,0 +1,264 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; +#include +#include +#include "mt7981b.dtsi" + +/ { + model = "ipTIME AX3000M"; + compatible = "iptime,ax3000m", "mediatek,mt7981"; + + aliases { + label-mac-device = &gmac0; + led-boot = &led_cpu; + led-failsafe = &led_cpu; + led-running = &led_cpu; + led-upgrade = &led_cpu; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " ubi.mtd=ubi rootfstype=squashfs"; + }; + + memory@40000000 { + reg = <0 0x40000000 0 0x10000000>; + device_type = "memory"; + }; + + leds { + compatible = "gpio-leds"; + + led_cpu: cpu { + function = LED_FUNCTION_CPU; + color = ; + gpios = <&pio 15 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + function = "LED_FUNCTION_WLAN_2GHZ"; + color = ; + gpios = <&pio 34 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + function = "LED_FUNCTION_WLAN_5GHZ"; + color = ; + gpios = <&pio 35 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&pio 0 GPIO_ACTIVE_HIGH>; + linux,code = ; + }; + }; +}; + +&pio { + nand_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = ; + bias-pull-up = ; + }; + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = ; + bias-pull-down = ; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins &gbe_led0_pins>; + + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cells = <&macaddr_factory_4 3>; + nvmem-cell-names = "mac-address"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + label = "wan"; + phy-mode = "gmii"; + phy-handle = <&int_gbe_phy>; + + nvmem-cells = <&macaddr_factory_4 1>; + nvmem-cell-names = "mac-address"; + }; +}; + +&mdio_bus { + switch: switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan4"; + }; + + port@1 { + reg = <1>; + label = "lan3"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan1"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; +}; + +&spi0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins>; + + spi_nand@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + reg = <0>; + + spi-max-frequency = <52000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + mediatek,bmt-remap-range = <0x000000 0x580000>; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x00 0x100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x100000 0x80000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x200000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_factory_4: macaddr@4 { + compatible = "mac-base"; + reg = <0x4 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x580000 0x6e00000>; + }; + }; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&xhci { + status = "okay"; +}; + +&wifi { + status = "okay"; + + band@0 { + reg = <0>; + nvmem-cells = <&macaddr_factory_4 0>; + nvmem-cell-names = "mac-address"; + }; + + band@1 { + reg = <1>; + nvmem-cells = <&macaddr_factory_4 0>; + nvmem-cell-names = "mac-address"; + }; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index c26ccf1d287..da0323dae08 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -119,6 +119,7 @@ case "$board" in addr=$(mtd_get_mac_binary "Factory" 0x4) [ "$PHYNBR" = "1" ] && macaddr_setbit_la $addr > /sys${DEVPATH}/macaddress ;; + iptime,ax3000m|\ iptime,ax3000sm) addr=$(mtd_get_mac_binary "Factory" 0x4) [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_unsetbit $(macaddr_unsetbit $(macaddr_unsetbit $(macaddr_setbit $addr 26) 25) 27) 28) > \ diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index c26b46624ab..06fad5b2f51 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -1273,6 +1273,26 @@ define Device/iptime_ax3000sm endef TARGET_DEVICES += iptime_ax3000sm +define Device/iptime_ax3000m + DEVICE_VENDOR := ipTIME + DEVICE_MODEL := AX3000M + DEVICE_DTS := mt7981b-iptime-ax3000m + DEVICE_DTS_DIR := ../dts + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 32768k + KERNEL := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k + IMAGES := factory.bin sysupgrade.bin + IMAGE/factory.bin := sysupgrade-tar | append-metadata | check-size | iptime-crc32 ax3000m + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware + SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-rfb +endef +TARGET_DEVICES += iptime_ax3000m + define Device/jcg_q30-pro DEVICE_VENDOR := JCG DEVICE_MODEL := Q30 PRO