Iris driver doesn't support non-PAS/TZ setup for setting up the Iris
core. It's expected that the ABI that is going to be used in a long-term
would be different from the defined venus-firmware subnode.
Granted that the SC7280 Chromebooks were cancelled before reaching wide
audience and granted the feature ABI changes, drop venus configuration
for SC7280 ChromeOS devices.
Suggested-by: Stephan Gerhold <stephan.gerhold@linaro.org> Cc: Douglas Anderson <dianders@chromium.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Acked-by: Douglas Anderson <dianders@chromium.org> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260131-venus-iris-flip-switch-v4-1-e10b886771e1@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There are variants from MSM8917 wingtech xiaomis what
are using goodix touch controller instead of focaltech.
Add goodix node for make it able to use touch on all
variants.
Barnabás Czémán [Sun, 15 Mar 2026 16:26:20 +0000 (17:26 +0100)]
arm64: dts: qcom: Make a common base from Redmi 5A
Redmi 5A was made by wingtech like Redmi 4A (rolex) and Redmi GO (tiare).
They are very similar, make a common base from riva for avoid
unnecessary code duplications.
Barnabás Czémán [Sun, 15 Mar 2026 16:26:19 +0000 (17:26 +0100)]
arm64: dts: qcom: msm8917-xiaomi-riva: Fix board-id for all bootloader
Redmi 5A comes with multiple bootloader versions where the expected
board-id is different.
Change the board-id to unified form what works on both bootloader
version.
Neil Armstrong [Thu, 19 Mar 2026 08:55:10 +0000 (09:55 +0100)]
arm64: dts: qcom: sm8650: Add sound DAI prefix for DP
Sound DAI devices exposing same set of mixers, e.g. each DisplayPort
controller, need to add dedicated prefix for these mixers to avoid
conflicts and to allow ALSA to properly configure given instance.
David Heidelberg [Fri, 20 Mar 2026 17:33:11 +0000 (18:33 +0100)]
arm64: dts: qcom: sdm845-xiaomi-beryllium: Mark l1a regulator as powered during boot
The regulator must be on, since it provides the display subsystem and
therefore the bootloader had turned it on before Linux booted.
Fixes: 77809cf74a8c ("arm64: dts: qcom: Add support for Xiaomi Poco F1 (Beryllium)") Signed-off-by: David Heidelberg <david@ixit.cz> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260320-beryllium-booton-v2-1-931d1be21eae@ixit.cz Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Krishna Kurapati [Mon, 23 Mar 2026 10:31:19 +0000 (16:01 +0530)]
arm64: dts: qcom: hamoa/purwa: Flatten usb controller nodes
Flatten usb controller nodes and update to using latest bindings and
flattened driver approach.
Tested this patch on CRD platform. For testing purpose, modified dr_mode
property and added usb-role-switch property to the 3 super speed capable
DRD controllers and valdiated both host and device mode. Also validated
host mode on the multiport controller.
The pinctrl nodes from sm6350.dtsi already contain a bias-* property, so
that needs to be deleted, otherwise the dtb will contain two conflicting
bias-* properties.
Vishnu Saini [Wed, 18 Mar 2026 19:08:19 +0000 (00:38 +0530)]
arm64: dts: qcom: monaco-evk: add lt8713sx bridge with displayport
Monaco-evk has LT8713sx which act as DP to 3 DP output
converter. Edp PHY from monaco soc is connected to lt8713sx
as input and output of lt8713sx is connected to 3 mini DP ports.
Two ports are available in mainboard and one port
is available on Mezz board.
lt8713sx is connected to soc over i2c0 and with reset gpio
connected to pin6 of ioexpander5.
Enable the edp nodes from monaco and enable lontium lt8713sx
bridge node.
Change the uart instances:
- uart6 is for bluetooth
- uart9 is for serial console (available on the uSD pinout)
Most OSes assume serial0 is for console UART. Bluetooth interface uses
UART interface. uart6 is standard debug console and uart9 bluetooth on
SDM845 devices.
The alert-slider is a tri-state sound profile switch found on the
OnePlus 6, Android maps the states to "silent", "vibrate" and "ring".
Expose them as ABS_SND_PROFILE events.
The previous GPIO numbers were wrong. Update them to the correct ones.
Abel Vesa [Fri, 20 Mar 2026 11:16:44 +0000 (13:16 +0200)]
arm64: dts: qcom: glymur-crd: Enable eDP display support
Enable the MDSS (Mobile Display SubSystem), the third DisplayPort
controller, and its PHY to drive the onboard eDP panel on the Glymur
CRD platform. Also describe the regulator supplying panel power.
The MDSS (Mobile Display SubSystem) on Glymur provides four DisplayPort
controllers. Describe them together with the display controller and eDP
PHY. Also add the combo PHY link and vco_div clocks to the display clock
controller, and connect the PHYs and DP endpoints in the graph.
Wesley Cheng [Fri, 20 Mar 2026 10:56:53 +0000 (12:56 +0200)]
arm64: dts: qcom: glymur-crd: Enable USB support
The Qualcomm Glymur Compute Reference Device comes with two Type-C ports,
one USB Type-A port, and a fingerprint reader connected over USB. Each
Type-C port is connected to one USB combo PHY and one M31 eUSB2 PHY. The
Type-A port is connected to the USB multi-port controller through one M31
eUSB2 PHY and one USB3 UNI PHY. The fingerprint reader is connected to the
USB_2 controller.
All M31 eUSB2 PHYs have associated eUSB2-to-USB 2.0 repeaters, which are
either integrated in SMB2370 PMICs or provided by dedicated NXP PTN3222
devices.
Enable all required controllers, PHYs, and repeaters, while specifying
their supplies. Also describe the PMIC GLINK graph for the Type-C
connectors.
Signed-off-by: Wesley Cheng <wesley.cheng@oss.qualcomm.com> Co-developed-by: Abel Vesa <abel.vesa@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Tested-by: Pankaj Patil <pankaj.patil@oss.qualcomm.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260320-dts-qcom-glymur-add-usb-support-v7-2-ba367eda6010@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Wesley Cheng [Fri, 20 Mar 2026 10:56:52 +0000 (12:56 +0200)]
arm64: dts: qcom: glymur: Add USB related nodes
The Glymur USB subsystem contains three USB 3.2 Gen 2 controllers,
one USB 3.2 multi-port controller, and one USB 2.0-only controller.
This includes five SS USB QMP PHYs (three combo and two UNI) and six M31
eUSB2 PHYs.
All controllers are based on SNPS DWC3, so describe them as Qualcomm
flattened DWC3 nodes.
Signed-off-by: Wesley Cheng <wesley.cheng@oss.qualcomm.com> Co-developed-by: Abel Vesa <abel.vesa@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Tested-by: Pankaj Patil <pankaj.patil@oss.qualcomm.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260320-dts-qcom-glymur-add-usb-support-v7-1-ba367eda6010@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Jishnu Prakash [Mon, 23 Mar 2026 06:19:41 +0000 (23:19 -0700)]
arm64: dts: qcom: kaanapali: Add PMIC devices
Add a spmi-pmic-arb device for the SPMI PMIC arbiter found on Kaanapali.
It has two subnodes corresponding to the SPMI0 bus controller and the
SPMI1 bus controller.
Also add dtsi files for PMH0104, PMH0110, PMD8028, PMIH0108, PMR735D
and PM8010 along with temp-alarm and GPIO nodes under them, which are
needed on Kaanapali.
Taniya Das [Wed, 25 Feb 2026 07:19:24 +0000 (23:19 -0800)]
arm64: dts: qcom: kaanapali: Add support for MM clock controllers for Kaanapali
Add the device nodes for the multimedia clock controllers (cambistmclkcc,
camcc, dispcc, videocc, gpucc and gxclkctl).
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com> Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260224-knp-dts-misc-v6-9-79d20dab8a60@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Prasad Kumpatla [Wed, 25 Feb 2026 07:19:23 +0000 (23:19 -0800)]
arm64: dts: qcom: kaanapali-mtp: Add audio support (WSA8845, WCD9395, DMIC)
Add support for audio on the Kaanapali MTP platform by introducing device
tree nodes for WSA8845 smart speaker amplifier for playback, DMIC
microphone for capture, and sound card routing. The WCD9395 codec is add
to supply MIC-BIAS, for enabling onboard microphone capture.
Prasad Kumpatla [Wed, 25 Feb 2026 07:19:20 +0000 (23:19 -0800)]
arm64: dts: qcom: kaanapali: Add support for audio
Introduce audio support for Kaanapali SoC by adding LPASS macro codecs,
TLMM pin controller and SoundWire controller with similar hardware
implementation to SM8750 platform. Also add GPR (Generic Pack Router) node
along with support for APM (Audio Process Manager) and PRM
(Proxy Resource Manager) audio services.
Signed-off-by: Prasad Kumpatla <prasad.kumpatla@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com> Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260224-knp-dts-misc-v6-5-79d20dab8a60@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
arm64: dts: qcom: kaanapali: Add TSENS and thermal zones
The Kaanapali includes seven TSENS instances, with a total of 55 thermal
sensors distributed across various locations on the SoC.
The TSENS max/reset threshold is configured to 130°C in the hardware.
Enable all TSENS instances, and define the thermal zones with a hot trip
at 120°C and critical trip at 125°C.
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manaf.pallikunhi@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260224-knp-dts-misc-v6-3-79d20dab8a60@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
arm64: dts: qcom: kaanapali: Add QUPv3 configuration for serial engines
Add device tree support for QUPv3 serial engine protocols on Kaanapali.
Kaanapali has 24 QUP serial engines across 4 QUP wrappers, each with
support of GPI DMA engines, and it also includes 5 I2C hubs.
Jie Gan [Wed, 25 Feb 2026 07:19:16 +0000 (23:19 -0800)]
arm64: dts: qcom: kaanapali: add coresight nodes
Add CoreSight nodes to enable trace paths such as TPDM->ETF and STM->ETF.
These devices are part of the AOSS, CDSP, QDSS, modem and some small
subsystems, such as DCC, GCC, ipcc and so on.
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com> Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260224-knp-dts-misc-v6-1-79d20dab8a60@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Pradeep P V K [Wed, 11 Feb 2026 13:29:25 +0000 (18:59 +0530)]
arm64: dts: qcom: hamoa: Add UFS nodes for x1e80100 SoC
Add UFS host controller and PHY nodes for x1e80100 SoC.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com> Reviewed-by: Taniya Das <taniya.das@oss.qualcomm.com> Reviewed-by: Manivannan Sadhasivam <mani@kernel.org> Signed-off-by: Pradeep P V K <pradeep.pragallapati@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260211132926.3716716-3-pradeep.pragallapati@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Loic Poulain [Fri, 13 Mar 2026 10:38:21 +0000 (10:38 +0000)]
arm64: dts: qcom: Add Arduino Monza (VENTUNO Q) board support
Add device tree support for the Arduino VENTUNO Q board,
based on the Qualcomm QCS8300 (Monaco) SoC.
The board features a Qualcomm Monza SoM and integrates various
peripherals, including:
- USB Type‑C connector with dual‑role support
- ADV7535 DSI‑to‑HDMI bridge
- MAX98091 audio codec
- 2.5G Ethernet PHY (HSGMII)
- PCIe0 (to onboard WiFi chipset and USB bridge)
- PCIe1 (to M2/nvme)
- Button (via GPIO‑keys)
Loic Poulain [Fri, 13 Mar 2026 10:38:19 +0000 (10:38 +0000)]
arm64: dts: qcom: Add Monaco Monza SoM
The Monaco Monza SoM is a compact computing module that integrates a
Monaco/QCS8300 System on Chip (SoC), along with essential components
optimized for IoT applications. It is designed to be mounted on
carrier boards, enabling the development of complete embedded systems.
The following components are described:
- Fixed S2S 1.8V rail
- PMM8654AU RPMh regulators (PMIC A and PMIC C)
- Display subsystem/phy supplies (DSI, DP)
- Enable GPU, GPI DMA, IRIS
- PCIe Gen4 for both controllers and PHY supply hookups
- QUPv3 firmware declarations
- REFGEN always-on workaround for USB2 HS PHY
- Remoteproc firmware names for ADSP, CDSP and GPDSP
- Ethernet SERDES supplies
- USB HS/SS PHY regulators
- On-SoM eMMC
arm64: dts: qcom: qcs6490-rb3gen2-industrial-mezzanine: Add second TC9563 PCIe switch node for PCIe1
Add a node for the second TC9563 PCIe switch on PCIe1, which is connected
in cascade to the first TC9563 switch via the former's downstream port.
Two embedded Ethernet devices are present on one of the downstream
ports of this second switch as well. All the ports present in the
node represent the downstream ports and embedded endpoints.
The second TC9563 is powered up via the same LDO regulators as the first
one, and these can be controlled via two GPIOs, which are already present
as fixed regulators. This TC9563 can also be configured through I2C.
Add a node for the TC9563 PCIe switch connected to PCIe0. The switch
has three downstream ports.Two embedded Ethernet devices are present
on one of the downstream ports. The other downstream ports route to
M.2 E key and PCIe x4 connector respectively. All the ports present
in the node represent the downstream ports and embedded endpoints.
Power to the TC9563 is supplied through two LDO regulators, which
are on by default and are added as fixed regulators. TC9563 can be
configured through I2C.
Since PCIe0 now routes to TC9563 instead of WCN6750, disable the
WCN6750 and WPSS device tree nodes to reflect the actual hardware
configuration and avoid probing issues.
The restriction on UHS-I speed modes was added to all SM8650 platforms
by copying it from SM8450 and SM8550 dtsi files, and it was an actually
reproducible problem due to the overclocking of SD cards. Since the latter
issue has been fixed in the SM8650 GCC driver, UHS-I speed modes are
working fine on SM8650 boards, below is the test performed on SM8650-HDK:
SDR50 speed mode:
mmc0: new UHS-I speed SDR50 SDHC card at address 0001
mmcblk0: mmc0:0001 00000 14.6 GiB
mmcblk0: p1
% dd if=/dev/mmcblk0p1 of=/dev/null bs=1M count=1024
1024+0 records in
1024+0 records out 1073741824 bytes (1.1 GB, 1.0 GiB) copied, 24.8086 s, 43.3 MB/s
SDR104 speed mode:
mmc0: new UHS-I speed SDR104 SDHC card at address 59b4
mmcblk0: mmc0:59b4 USDU1 28.3 GiB
mmcblk0: p1
% dd if=/dev/mmcblk0p1 of=/dev/null bs=1M count=1024
1024+0 records in
1024+0 records out 1073741824 bytes (1.1 GB, 1.0 GiB) copied, 12.9448 s, 82.9 MB/s
Unset the UHS-I speed mode restrictions from the SM8550 platform dtsi
file, there is no indication that the SDHC controller is broken.
Fixes: 10e024671295 ("arm64: dts: qcom: sm8650: add interconnect dependent device nodes") Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Link: https://lore.kernel.org/r/20260314023715.357512-7-vladimir.zapolskiy@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The restriction on UHS-I speed modes was added to all SM8550 platforms
by copying it from SM8450 dtsi file, and due to the overclocking of SD
cards it was an actually reproducible problem. Since the latter issue
has been fixed, UHS-I speed modes are working fine on SM8550 boards,
below is the test performed on SM8550-HDK:
SDR50 speed mode:
mmc0: new UHS-I speed SDR50 SDHC card at address 0001
mmcblk0: mmc0:0001 00000 14.6 GiB
mmcblk0: p1
% dd if=/dev/mmcblk0p1 of=/dev/null bs=1M count=1024
1024+0 records in
1024+0 records out 1073741824 bytes (1.1 GB, 1.0 GiB) copied, 23.5468 s, 45.6 MB/s
SDR104 speed mode:
mmc0: new UHS-I speed SDR104 SDHC card at address 59b4
mmcblk0: mmc0:59b4 USDU1 28.3 GiB
mmcblk0: p1
% dd if=/dev/mmcblk0p1 of=/dev/null bs=1M count=1024
1024+0 records in
1024+0 records out 1073741824 bytes (1.1 GB, 1.0 GiB) copied, 11.9819 s, 89.6 MB/s
Unset the UHS-I speed mode restrictions from the SM8550 platform dtsi
file, there is no indication that the SDHC controller is broken.
Fixes: ffc50b2d3828 ("arm64: dts: qcom: Add base SM8550 dtsi") Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Link: https://lore.kernel.org/r/20260314023715.357512-6-vladimir.zapolskiy@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The reported problem of some non-working UHS-I speed modes on SM8450
originates in commit 0a631a36f724 ("arm64: dts: qcom: Add device tree
for Sony Xperia 1 IV"), and then it was spread to all SM8450 powered
platforms by commit 9d561dc4e5cc ("arm64: dts: qcom: sm8450: disable
SDHCI SDR104/SDR50 on all boards").
The tests show that the rootcause of the problem was related to an
overclocking of SD cards, and it's fixed later on by commit a27ac3806b0a
("clk: qcom: gcc-sm8450: Use floor ops for SDCC RCGs").
Since then both SDR50 and SDR104 speed modes are working fine on SM8450,
tested on SM8450-HDK:
SDR50 speed mode:
mmc0: new UHS-I speed SDR50 SDHC card at address 0001
mmcblk0: mmc0:0001 00000 14.6 GiB
mmcblk0: p1
% dd if=/dev/mmcblk0p1 of=/dev/null bs=1M count=1024
1024+0 records in
1024+0 records out 1073741824 bytes (1.1 GB, 1.0 GiB) copied, 24.6254 s, 43.6 MB/s
SDR104 speed mode:
mmc0: new UHS-I speed SDR104 SDHC card at address 59b4
mmcblk0: mmc0:59b4 USDU1 28.3 GiB
mmcblk0: p1
% dd if=/dev/mmcblk0p1 of=/dev/null bs=1M count=1024
1024+0 records in
1024+0 records out 1073741824 bytes (1.1 GB, 1.0 GiB) copied, 12.3266 s, 87.1 MB/s
Remove the restrictions on SD card speed modes from the SM8450 platform
dtsi file and enable UHS-I speed modes.
Fixes: 9d561dc4e5cc ("arm64: dts: qcom: sm8450: disable SDHCI SDR104/SDR50 on all boards") Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Link: https://lore.kernel.org/r/20260314023715.357512-5-vladimir.zapolskiy@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
arm64: dts: qcom: hamoa: Fix xo clock supply of platform SD host controller
The expected frequency of SD host controller core supply clock is 19.2MHz,
while RPMH_CXO_CLK clock frequency on SM8650 platform is 38.4MHz.
Apparently the overclocked supply clock could be good enough on some
boards and even with the most of SD cards, however some low-end UHS-I
SD cards in SDR104 mode of the host controller produce I/O errors in
runtime, fortunately this problem is gone, if the "xo" clock frequency
matches the expected 19.2MHz clock rate.
Fixes: ffb21c1e19b1 ("arm64: dts: qcom: x1e80100: Describe the SDHC controllers") Reported-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20260314023715.357512-4-vladimir.zapolskiy@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
arm64: dts: qcom: sm8650: Fix xo clock supply of SD host controller
The expected frequency of SD host controller core supply clock is 19.2MHz,
while RPMH_CXO_CLK clock frequency on SM8650 platform is 38.4MHz.
Apparently the overclocked supply clock could be good enough on some
boards and even with the most of SD cards, however some low-end UHS-I
SD cards in SDR104 mode of the host controller produce I/O errors in
runtime, fortunately this problem is gone, if the "xo" clock frequency
matches the expected 19.2MHz clock rate.
Fixes: 10e024671295 ("arm64: dts: qcom: sm8650: add interconnect dependent device nodes") Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20260314023715.357512-3-vladimir.zapolskiy@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
arm64: dts: qcom: sm8550: Fix xo clock supply of platform SD host controller
The expected frequency of SD host controller core supply clock is 19.2MHz,
while RPMH_CXO_CLK clock frequency on SM8650 platform is 38.4MHz.
Apparently the overclocked supply clock could be good enough on some
boards and even with the most of SD cards, however some low-end UHS-I
SD cards in SDR104 mode of the host controller produce I/O errors in
runtime, fortunately this problem is gone, if the "xo" clock frequency
matches the expected 19.2MHz clock rate.
Fixes: ffc50b2d3828 ("arm64: dts: qcom: Add base SM8550 dtsi") Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20260314023715.357512-2-vladimir.zapolskiy@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Konrad Dybcio [Tue, 17 Mar 2026 14:41:16 +0000 (15:41 +0100)]
arm64: dts: qcom: sm8450: Fix GIC_ITS range length
Currently, the GITS_SGIR register is cut off. Fix it up.
Fixes: fc8b0b9b630d ("arm64: dts: qcom: sm8450 add ITS device tree node") Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260317-topic-its_range_fixup-v1-3-49be8076adb1@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
arm64: dts: qcom: sm8750-mtp: Enable USB headset and Type-C accessory mode
MTP8750 does not have audio jack connected and relies on USB mux
(WCD9395). Add necessary nodes for proper audio headset support along
with USB Type-C accessory mode and orientation.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260317-sm8750-display-dts-v5-3-fb53371e251c@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Dmitry Baryshkov [Fri, 13 Mar 2026 15:27:13 +0000 (17:27 +0200)]
arm64: dts: qcom: sm8750: correct Iris corners for the MXC rail
The corners of the MVS0 / MVS0C clocks on the MMCX rail don't always
match the PLL corners on the MXC rail. Correct the performance corners
for the MXC rail following the PLL documentation.
Dmitry Baryshkov [Fri, 13 Mar 2026 15:27:12 +0000 (17:27 +0200)]
arm64: dts: qcom: sm8650: correct Iris corners for the MXC rail
The corners of the MVS0 / MVS0C clocks on the MMCX rail don't always
match the PLL corners on the MXC rail. Correct the performance corners
for the MXC rail following the PLL documentation.
Dmitry Baryshkov [Fri, 13 Mar 2026 15:27:11 +0000 (17:27 +0200)]
arm64: dts: qcom: sm8550: correct Iris corners for the MXC rail
The corners of the MVS0 / MVS0C clocks on the MMCX rail don't always
match the PLL corners on the MXC rail. Correct the performance corners
for the MXC rail following the PLL documentation.
Dmitry Baryshkov [Fri, 13 Mar 2026 15:27:10 +0000 (17:27 +0200)]
arm64: dts: qcom: monaco: correct Iris corners for the MXC rail
The corners of the MVS0 / MVS0C clocks on the MMCX rail don't always
match the PLL corners on the MXC rail. Correct the performance corners
for the MXC rail following the PLL documentation.
Dmitry Baryshkov [Fri, 13 Mar 2026 15:27:09 +0000 (17:27 +0200)]
arm64: dts: qcom: lemans: correct Iris corners for the MXC rail
The corners of the MVS0 / MVS0C clocks on the MMCX rail don't always
match the PLL corners on the MXC rail. Correct the performance corners
for the MXC rail following the PLL documentation.
Fixes: 7bc95052c64f ("arm64: dts: qcom: sa8775p: add support for video node") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260313-iris-fix-corners-v1-2-32a393c25dda@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Dmitry Baryshkov [Fri, 13 Mar 2026 15:27:08 +0000 (17:27 +0200)]
arm64: dts: qcom: hamoa: correct Iris corners for the MXC rail
The corners of the MVS0 / MVS0C clocks on the MMCX rail don't always
match the PLL corners on the MXC rail. Correct the performance corners
for the MXC rail following the PLL documentation.
Abel Vesa [Wed, 18 Mar 2026 10:19:34 +0000 (12:19 +0200)]
arm64: dts: qcom: eliza: Enable Eliza MTP board support
The MTP is a one of the boards that comes with the Eliza SoC.
So add dedicated board dts for it.
The initial support enables:
- UART debug console
- Ob-board UFS storage
- Qualcomm RPMh regulators (PMIC) and VPH_PWR
- board specific clocks & reserved GPIO ranges
Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260318-eliza-base-dt-v3-3-8a50bd2201ed@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Abel Vesa [Wed, 18 Mar 2026 10:19:33 +0000 (12:19 +0200)]
arm64: dts: qcom: Introduce Eliza Soc base dtsi
Introduce the initial support for the Qualcomm Eliza SoC. It comes in
different flavors. There is SM7750 for mobiles and then QC7790S/M for IoT.
Describe the common parts under a common dtsi.
The initial submission enables support for:
- CPU nodes with cpufreq and cpuidle support
- Global Clock Controller (GCC)
- Resource State Coordinator (RSC) with clock controller & genpd provider
- Interrupt controller
- Power Domain Controller (PDC)
- Vendor specific SMMU
- SPMI bus arbiter
- Top Control and Status Register (TCSR)
- Top Level Mode Multiplexer (TLMM)
- Debug UART
- Reserved memory nodes
- Interconnect providers
- System timer
- UFS
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260318-eliza-base-dt-v3-2-8a50bd2201ed@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Abel Vesa [Wed, 18 Mar 2026 10:19:32 +0000 (12:19 +0200)]
dt-bindings: arm: qcom: Document Eliza SoC and its MTP board
Qualcomm Eliza SoC comes with different flavors. There is SM7750 for
mobiles and then QC7790S/M for IoT. One of the boards that comes with
Eliza SoC is the MTP.
So document both the SoC and MTP board compatibles.
Bjorn Andersson [Thu, 19 Mar 2026 02:26:37 +0000 (21:26 -0500)]
Merge branch 'icc-eliza' of https://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into HEAD
Merge the Eliza interconnect DeviceTree bindings from topic branch, in
order to introduce the interconnect constants used in the Eliza
DeviceTree source.
Introduce support for the Mahua SoC and the CRD based on it. Some of
the notable differences are the absent CPU cluster, interconnect, TLMM,
thermal zones and adjusted PCIe west clocks. Everything else should
work as-is.
dt-bindings: arm: qcom: Document Mahua SoC and board
Mahua is a derivative of Glymur SoC with the third CPU cluster disabled.
Document the compatible strings for the Mahua SoC and the Compute
Reference Device (CRD) board based on it.
Wei Deng [Mon, 2 Mar 2026 02:46:58 +0000 (08:16 +0530)]
arm64: dts: qcom: qcs8300-ride: Enable Bluetooth support
Enable BT on qcs8300-ride by adding a BT device tree node.
Since the platform uses the QCA6698 Bluetooth chip. While
the QCA6698 shares the same IP core as the WCN6855, it has
different RF components and RAM sizes, requiring new firmware
files. Use the firmware-name property to specify the NVM and
rampatch firmware to load.
Tobias Heider [Thu, 26 Feb 2026 14:04:30 +0000 (15:04 +0100)]
arm64: dts: qcom: add missing denali-oled.dtb to Makefile
The DeviceTree for the OLED variant of the Microsoft Surface Pro 11th
Edition was originally added in commit '0d72ccaa1e84 ("arm64: dts: qcom:
Add support for X1-based Surface Pro 11")'. The original patch on the
mailing list also added the new device tree to the Makefile but that
part seems to have been dropped (by accident) when it got merged.
Signed-off-by: Tobias Heider <tobias.heider@canonical.com> Fixes: 0d72ccaa1e84 ("arm64: dts: qcom: Add support for X1-based Surface Pro 11") Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260226140429.232544-3-tobias.heider@canonical.com
[bjorn: Rewrote commit message reference to offending commit] Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Erikas Bitovtas [Wed, 25 Feb 2026 14:43:24 +0000 (16:43 +0200)]
arm64: dts: qcom: msm8939-asus-z00t: add ambient light and proximity sensor
This device uses Capella CM36686 as its ambient light and proximity
sensor. It is fully compatible with Vishay VCNL4040. Downstream device
tree reports Capella CM36283, but upon probe, a device ID for CM36686 is
actually found. This commit adds support for Capella CM36686 ambient
light and proximity sensor.
projects / thirdparty / kernel / linux.git / log
