e1000e: fix cyclic resets at link up with active tx
I'm seeing series of e1000e resets (sometimes endless) at system boot
if something generates tx traffic at this time. In my case this is
netconsole who sends message "e1000e 0000:02:00.0: Some CPU C-states
have been disabled in order to enable jumbo frames" from e1000e itself.
As result e1000_watchdog_task sees used tx buffer while carrier is off
and start this reset cycle again.
[ 17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000
[ 23.033336] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 27.174495] 8021q: 802.1Q VLAN Support v1.8
[ 27.174513] 8021q: adding VLAN 0 to HW filter on device eth1
[ 30.671724] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation
[ 30.898564] netpoll: netconsole: local port 6666
[ 30.898566] netpoll: netconsole: local IPv6 address 2a02:6b8:0:80b:beae:c5ff:fe28:23f8
[ 30.898567] netpoll: netconsole: interface 'eth1'
[ 30.898568] netpoll: netconsole: remote port 6666
[ 30.898568] netpoll: netconsole: remote IPv6 address 2a02:6b8:b000:605c:e61d:2dff:fe03:3790
[ 30.898569] netpoll: netconsole: remote ethernet address b0:a8:6e:f4:ff:c0
[ 30.917747] console [netcon0] enabled
[ 30.917749] netconsole: network logging started
[ 31.453353] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.185730] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.321840] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.465822] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.597423] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.745417] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.877356] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.005441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.157376] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.289362] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.417441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
This patch flushes tx buffers only once when carrier is off
rather than at each watchdog iteration.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Sun, 13 Jan 2019 09:22:31 +0000 (11:22 +0200)]
igc: Remove unneeded code
Remove the 'igc_get_link_up_info_base method' from igc_base.c file.
Use the 'igc_get_speed_and_duplex_copper' method directly and reduce
the code redundancy.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher [Fri, 4 Jan 2019 01:17:03 +0000 (17:17 -0800)]
e1000e: fix a missing check for return value
The change is based on the issue found by Kangjie Lu <kjlu@umn.edu> where
we not checking the return value of a register read/write which could result
in a NULL pointer dereference if the read/write fails.
Since we are only trying to disable the far-end loopback, if the read
and write of register fails, we do not want to bail out of the function.
We just want to log that it failed to disable and continue on.
CC: Sasha Neftin <sasha.neftin@intel.com> CC: Kangjie Lu <kjlu@umn.edu> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Fri, 4 Jan 2019 00:49:02 +0000 (16:49 -0800)]
fm10k: TRIVIAL cleanup of extra spacing in function comment
The function comment for fm10k_iov_msg_msix_pf has an extra space in
a sentence, which is unnecessary.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jiri Kosina [Wed, 2 Jan 2019 19:20:33 +0000 (20:20 +0100)]
ixgbe: remove magic constant in ixgbe_reset_hw_82599()
ixgbe_reset_hw_82599() resets the value of hw->mac.num_rar_entries to
pre-defined value of 128. Let's get rid of that hardcoded literal, and use
IXGBE_82599_RAR_ENTRIES instead, the same way the normal initialization
path does.
Signed-off-by: Jiri Kosina <jkosina@suse.cz> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Tue, 18 Dec 2018 09:29:54 +0000 (11:29 +0200)]
igc: Fix code redundancy
Remove redundant igc_check_for_link_base code and replace it with
an igc_check_for_copper_link method.
Fix duplication of IGC_ADVTXD_PAYLEN_SHIFT mask declaration.
Remove obsolete IGC_SCVPC register definition.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Tue, 11 Dec 2018 16:55:41 +0000 (18:55 +0200)]
igc: Remove unreachable code from igc_phy.c file
Address community comment.
Remove the unreachable code leads to the static checker warning.
PHY functionality will be added later per demand.
Reported by Dan Carpenter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kai-Heng Feng [Tue, 11 Dec 2018 07:59:37 +0000 (15:59 +0800)]
e1000e: Exclude device from suspend direct complete optimization
e1000e sets different WoL settings in system suspend callback and
runtime suspend callback.
The suspend direct complete optimization leaves e1000e in runtime
suspended state with wrong WoL setting during system suspend.
To fix this, we need to disable suspend direct complete optimization to
let e1000e always use suspend callback to set correct WoL during system
suspend.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Russell King [Mon, 4 Feb 2019 23:35:59 +0000 (23:35 +0000)]
net: marvell: mvpp2: fix lack of link interrupts
Sven Auhagen reports that if he changes a SFP+ module for a SFP module
on the Macchiatobin Single Shot, the link does not come back up. For
Sven, it is as easy as:
- Insert a SFP+ module connected, and use ping6 to verify link is up.
- Remove SFP+ module
- Insert SFP 1000base-X module use ping6 to verify link is up: Link
up event did not trigger and the link is down
but that doesn't show the problem for me. Locally, this has been
reproduced by:
- Boot with no modules.
- Insert SFP+ module, confirm link is up.
- Replace module with 25000base-X module. Confirm link is up.
- Set remote end down, link is reported as dropped at both ends.
- Set remote end up, link is reported up at remote end, but not local
end due to lack of link interrupt.
Fix this by setting up both GMAC and XLG interrupts for port 0, but
only unmasking the appropriate interrupt according to the current mode
set in the mac_config() method. However, only do the mask/unmask
dance when we are really changing the link mode to avoid missing any
link interrupts.
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 4 Feb 2019 23:35:54 +0000 (23:35 +0000)]
net: marvell: mvpp2: use phy_interface_mode_is_8023z() helper
Use the phy_interface_mode_is_8023z() helper for detecting interface
modes that use 802.3z serial encoding. This is equivalent to testing
for both 1000base-X and 2500base-X.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 Feb 2019 18:34:34 +0000 (10:34 -0800)]
Merge branch 'nixge-Fixed-link-support'
Moritz Fischer says:
====================
nixge: Fixed-link support
This series adds fixed-link support to nixge.
The first patch corrects the binding to correctly reflect
hardware that does not come with MDIO cores instantiated.
The second patch adds fixed link support to the driver.
The third patch updates the binding document with the now
optional (formerly required) phy-handle property and references
the fixed-link docs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Moritz Fischer [Mon, 4 Feb 2019 17:30:38 +0000 (09:30 -0800)]
net: nixge: Make mdio child node optional
Make MDIO child optional and only instantiate the
MDIO bus if the child is actually present.
There are currently no (in-tree) users of this
binding; all (out-of-tree) users use overlays that
get shipped together with the FPGA images that contain
the IP.
This will significantly increase maintainabilty
of future revisions of this IP.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Moritz Fischer <mdf@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Mon, 4 Feb 2019 10:26:18 +0000 (11:26 +0100)]
net: phy: fixed-phy: Drop GPIO from fixed_phy_add()
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Tonghao Zhang [Tue, 29 Jan 2019 21:23:24 +0000 (13:23 -0800)]
net/mlx5: Fix code style issue in mlx driver
Add the tab before '}' and keep the code style consistent.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Here's a set of 7 patches against DaveM's 'net-next.git' repo. I'm implemeting
the simple RX checksum offload (like was done for the 'ravb' driver by Simon
Horman); it has been only tested on the R8A7740 and R8A77980 SoCs, the other
SoCs should just work (according to their manuals)...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Mon, 4 Feb 2019 18:08:54 +0000 (21:08 +0300)]
sh_eth: offload RX checksum on R8A7740
The R-Mobile A1 (R8A7740) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MAC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Mon, 4 Feb 2019 18:06:52 +0000 (21:06 +0300)]
sh_eth: RX checksum offload support
Add support for the RX checksum offload. This is enabled by default and
may be disabled and re-enabled using 'ethtool':
# ethtool -K eth0 rx off
# ethtool -K eth0 rx on
Some Ether MACs provide a simple checksumming scheme which appears to be
completely compatible with CHECKSUM_COMPLETE: sum of all packet data after
the L2 header is appended to packet data; this may be trivially read by
the driver and used to update the skb accordingly. The same checksumming
scheme is implemented in the EtherAVB MACs and now supported by the 'ravb'
driver.
In terms of performance, throughput is close to gigabit line rate with the
RX checksum offload both enabled and disabled. The 'perf' output, however,
appears to indicate that significantly less time is spent in do_csum() --
this is as expected.
Test results with RX checksum offload enabled:
~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
Sergei Shtylyov [Mon, 4 Feb 2019 18:05:55 +0000 (21:05 +0300)]
sh_eth: rename sh_eth_cpu_data::hw_checksum
Commit 62e04b7e0e3c ("sh_eth: rename 'sh_eth_cpu_data::hw_crc'") renamed
the field to 'hw_checksum' for the Ether DMAC "intelligent checksum",
however some Ether MACs implement a simpler checksumming scheme, so that
name now seems misleading. Rename that field to 'csmr' as the "intelligent
checksum" is always controlled by the CSMR register.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 887feae36aee ("socket: Add SO_TIMESTAMP[NS]_NEW") Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 Feb 2019 04:25:31 +0000 (20:25 -0800)]
net: Fix fall through warning in y2038 tstamp changes.
net/core/sock.c: In function 'sock_setsockopt':
net/core/sock.c:914:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
sock_set_flag(sk, SOCK_TSTAMP_NEW);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/core/sock.c:915:2: note: here
case SO_TIMESTAMPING_OLD:
^~~~
Fixes: 9718475e6908 ("socket: Add SO_TIMESTAMPING_NEW") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 3 Feb 2019 22:31:04 +0000 (14:31 -0800)]
Merge branch 'phy-aquantia-improvements'
Heiner Kallweit says:
====================
net: phy: aquantia: number of improvements
This patch series is based on work from Andrew. I adjusted and added
certain parts. The series improves few aspects of driver, no functional
change intended.
v2:
- add my SoB to patch 1
- leave kernel.h in in patch 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 3 Feb 2019 20:19:06 +0000 (21:19 +0100)]
net: phy: aquantia: replace magic numbers with constants
Replace magic numbers with proper constants. The original patch is
from Andrew, I extended / adjusted certain parts:
- Use decimal bit numbers. The datasheet uses hex bit numbers 0 .. F.
- Order defines from highest to lowest bit numbers
- correct some typos
- add constant MDIO_AN_TX_VEND_INT_MASK2_LINK
- Remove few functional improvements from the patch, they will come as
a separate patch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 3 Feb 2019 20:16:18 +0000 (21:16 +0100)]
net: phy: aquantia: Shorten name space prefix to aqr_
aquantia_ as a name space prefix is rather long, resulting in lots of
lines needing wrapping, reducing readability. Use the prefix aqr_
instead, which fits with the vendor naming there devices aqr107, for
example.
v2:
- add SoB from Heiner
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sat, 2 Feb 2019 01:56:28 +0000 (17:56 -0800)]
net: devlink: report cell size of shared buffers
Shared buffer allocation is usually done in cell increments.
Drivers will either round up the allocation or refuse the
configuration if it's not an exact multiple of cell size.
Drivers know exactly the cell size of shared buffer, so help
out users by providing this information in dumps.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The series introduces new socket timestamps that are
y2038 safe.
The time data types used for the existing socket timestamp
options: SO_TIMESTAMP, SO_TIMESTAMPNS and SO_TIMESTAMPING
are not y2038 safe. The series introduces SO_TIMESTAMP_NEW,
SO_TIMESTAMPNS_NEW and SO_TIMESTAMPING_NEW to replace these.
These new timestamps can be used on all architectures.
The alternative considered was to extend the sys_setsockopt()
by using the flags. We did not receive any strong opinions about
either of the approaches. Hence, this was chosen, as glibc folks
preferred this.
The series does not deal with updating the internal kernel socket
calls like rxrpc to make them y2038 safe. This will be dealt
with separately.
Note that the timestamps behavior already does not match the
man page specific behavior:
SIOCGSTAMP
This ioctl should only be used if the socket option SO_TIMESTAMP
is not set on the socket. Otherwise, it returns the timestamp of
the last packet that was received while SO_TIMESTAMP was not set,
or it fails if no such packet has been received,
(i.e., ioctl(2) returns -1 with errno set to ENOENT).
The recommendation is to update the man page to remove the above statement.
The overview of the socket timestamp series is as below:
1. Delete asm specific socket.h when possible.
2. Support SO/SCM_TIMESTAMP* options only in userspace.
3. Rename current SO/SCM_TIMESTAMP* to SO/SCM_TIMESTAMP*_OLD.
3. Alter socket options so that SOCK_RCVTSTAMPNS does
not rely on SOCK_RCVTSTAMP.
4. Introduce y2038 safe types for socket timestamp.
5. Introduce new y2038 safe socket options SO/SCM_TIMESTAMP*_NEW.
6. Intorduce new y2038 safe socket timeout options.
Changes since v4:
* Fixed the typo in calling sock_get_timeout()
Changes since v3:
* Rebased onto net-next and fixups as per review comments
* Merged the socket timeout series
* Integrated Arnd's patch to simplify compat handling of timeout syscalls
Changes since v2:
* Removed extra functions to reduce diff churn as per code review
Changes since v1:
* Dropped the change to disentangle sock flags
* Renamed sock_timeval to __kernel_sock_timeval
* Updated a few comments
* Added documentation changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Deepa Dinamani [Sat, 2 Feb 2019 15:34:53 +0000 (07:34 -0800)]
socket: Rename SO_RCVTIMEO/ SO_SNDTIMEO with _OLD suffixes
SO_RCVTIMEO and SO_SNDTIMEO socket options use struct timeval
as the time format. struct timeval is not y2038 safe.
The subsequent patches in the series add support for new socket
timeout options with _NEW suffix that will use y2038 safe
data structures. Although the existing struct timeval layout
is sufficiently wide to represent timeouts, because of the way
libc will interpret time_t based on user defined flag, these
new flags provide a way of having a structure that is the same
for all architectures consistently.
Rename the existing options with _OLD suffix forms so that the
right option is enabled for userspace applications according
to the architecture and time_t definition of libc.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Cc: ccaulfie@redhat.com Cc: deller@gmx.de Cc: paulus@samba.org Cc: ralf@linux-mips.org Cc: rth@twiddle.net Cc: cluster-devel@redhat.com Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-alpha@vger.kernel.org Cc: linux-arch@vger.kernel.org Cc: linux-mips@vger.kernel.org Cc: linux-parisc@vger.kernel.org Cc: sparclinux@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Deepa Dinamani [Sat, 2 Feb 2019 15:34:52 +0000 (07:34 -0800)]
socket: Update timestamping Documentation
With the new y2038 safe timestamping options added, update the
documentation to reflect the changes.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Deepa Dinamani [Sat, 2 Feb 2019 15:34:50 +0000 (07:34 -0800)]
socket: Add SO_TIMESTAMP[NS]_NEW
Add SO_TIMESTAMP_NEW and SO_TIMESTAMPNS_NEW variants of
socket timestamp options.
These are the y2038 safe versions of the SO_TIMESTAMP_OLD
and SO_TIMESTAMPNS_OLD for all architectures.
Note that the format of scm_timestamping.ts[0] is not changed
in this patch.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Cc: jejb@parisc-linux.org Cc: ralf@linux-mips.org Cc: rth@twiddle.net Cc: linux-alpha@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-parisc@vger.kernel.org Cc: linux-rdma@vger.kernel.org Cc: netdev@vger.kernel.org Cc: sparclinux@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Deepa Dinamani [Sat, 2 Feb 2019 15:34:49 +0000 (07:34 -0800)]
socket: Add struct __kernel_sock_timeval
The new type is meant to be used as a y2038 safe structure
to be used as part of cmsg data.
Presently the SO_TIMESTAMP socket option uses struct timeval
for timestamps. This is not y2038 safe.
Subsequent patches in the series add new y2038 safe socket
option to be used in the place of SO_TIMESTAMP_OLD.
struct __kernel_sock_timeval will be used as the timestamp
format at that time.
struct __kernel_sock_timeval also maintains the same layout
across 32 bit and 64 bit ABIs.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Deepa Dinamani [Sat, 2 Feb 2019 15:34:48 +0000 (07:34 -0800)]
socket: Use old_timeval types for socket timestamps
As part of y2038 solution, all internal uses of
struct timeval are replaced by struct __kernel_old_timeval
and struct compat_timeval by struct old_timeval32.
Make socket timestamps use these new types.
This is mainly to be able to verify that the kernel build
is y2038 safe when such non y2038 safe types are not
supported anymore.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Cc: isdn@linux-pingi.de Signed-off-by: David S. Miller <davem@davemloft.net>
Deepa Dinamani [Sat, 2 Feb 2019 15:34:47 +0000 (07:34 -0800)]
arch: sparc: Override struct __kernel_old_timeval
struct __kernel_old_timeval is supposed to have the same
layout as struct timeval. But, it was inadvarently missed
that __kernel_suseconds has a different definition for
sparc64.
Provide an asm-specific override that fixes it.
Reported-by: Arnd Bergmann <arnd@arndb.de> Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Cc: sparclinux@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Deepa Dinamani [Sat, 2 Feb 2019 15:34:46 +0000 (07:34 -0800)]
sockopt: Rename SO_TIMESTAMP* to SO_TIMESTAMP*_OLD
SO_TIMESTAMP, SO_TIMESTAMPNS and SO_TIMESTAMPING options, the
way they are currently defined, are not y2038 safe.
Subsequent patches in the series add new y2038 safe versions
of these options which provide 64 bit timestamps on all
architectures uniformly.
Hence, rename existing options with OLD tag suffixes.
Also note that kernel will not use the untagged SO_TIMESTAMP*
and SCM_TIMESTAMP* options internally anymore.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Cc: deller@gmx.de Cc: dhowells@redhat.com Cc: jejb@parisc-linux.org Cc: ralf@linux-mips.org Cc: rth@twiddle.net Cc: linux-afs@lists.infradead.org Cc: linux-alpha@vger.kernel.org Cc: linux-arch@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-parisc@vger.kernel.org Cc: linux-rdma@vger.kernel.org Cc: sparclinux@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Deepa Dinamani [Sat, 2 Feb 2019 15:34:45 +0000 (07:34 -0800)]
arch: Use asm-generic/socket.h when possible
Many architectures maintain an arch specific copy of the
file even though there are no differences with the asm-generic
one. Allow these architectures to use the generic one instead.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> Acked-by: Willem de Bruijn <willemb@google.com> Cc: chris@zankel.net Cc: fenghua.yu@intel.com Cc: tglx@linutronix.de Cc: schwidefsky@de.ibm.com Cc: linux-ia64@vger.kernel.org Cc: linux-xtensa@linux-xtensa.org Cc: linux-s390@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sat, 2 Feb 2019 15:34:44 +0000 (07:34 -0800)]
socket: move compat timeout handling into sock.c
This is a cleanup to prepare for the addition of 64-bit time_t
in O_SNDTIMEO/O_RCVTIMEO. The existing compat handler seems
unnecessarily complex and error-prone, moving it all into the
main setsockopt()/getsockopt() implementation requires half
as much code and is easier to extend.
32-bit user space can now use old_timeval32 on both 32-bit
and 64-bit machines, while 64-bit code can use
__old_kernel_timeval.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Deepa Dinamani [Sat, 2 Feb 2019 15:34:43 +0000 (07:34 -0800)]
selftests: add missing include unistd
Compiling rxtimestamp.c generates error messages due to
non-existing declaration for write() library call.
Add missing unistd.h include to provide the declaration and
silence the error.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()
{t4/t4_vf}_change_mac() API's were only doing additions to MPS_TCAM.
This will fail, when the number of tcam entries is limited particularly
in vf's.
This fix programs hash region with the mac address, when TCAM
addtion fails for {t4/t4vf}_change_mac(). Since the locally maintained
driver list for hash entries is shared across mac_{sync/unsync}(),
added an extra parameter if_mac to track the address added thorugh
{t4/t4vf}_change_mac()
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Chron [Thu, 31 Jan 2019 23:00:40 +0000 (15:00 -0800)]
ipv4/igmp: Don't drop IGMP pkt with zeros src addr
Don't drop IGMP packets with a source address of all zeros which are
IGMP proxy reports. This is documented in Section 2.1.1 IGMP
Forwarding Rules of RFC 4541 IGMP and MLD Snooping Switches
Considerations.
Signed-off-by: Edward Chron <echron@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 3 Feb 2019 15:07:33 +0000 (16:07 +0100)]
net: phy: realtek: add generic Realtek PHY driver
The integrated PHY's of later RTL8168 network chips report the generic
PHYID 0x001cc800 (Realtek OUI, model and revision number both set to
zero) and therefore currently the genphy driver is used.
To be able to use the paged version of e.g. phy_write() we need a
PHY driver with the read_page and write_page callbacks implemented.
So basically make a copy of the genphy driver, just with the
read_page and write_page callbacks being set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Sat, 2 Feb 2019 11:41:29 +0000 (11:41 +0000)]
atl1c: fix indentation issue on an if statement
An if statement is indented one level too deep, fix this by removing
the extra tabs. Also add some spaces to the dev_warn arguments to clean
up checkpatch warnings.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
liuzhongzhu [Sat, 2 Feb 2019 14:39:37 +0000 (22:39 +0800)]
net: hns3: MAC table entry count function increases operation 0 value protection measures
When updating the available MAC VLAN table counts,
MAC VLAN table entry count function adds
operation 0 value protection measures.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
liuzhongzhu [Sat, 2 Feb 2019 14:39:36 +0000 (22:39 +0800)]
net: hns3: modify the upper limit judgment condition
In order to prevent the variable anomaly from being larger than desc_num,
the upper limit judgment condition becomes >=.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Sat, 2 Feb 2019 14:39:35 +0000 (22:39 +0800)]
net: hns3: don't allow user to change vlan filter state
When user disables vlan filter, and adds vlan device, it won't
notify the driver the update the vlan filter. In this case, when
user enables vlan filter again, the packets with new vlan tag
will be filtered by vlan filter.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
liuzhongzhu [Sat, 2 Feb 2019 14:39:34 +0000 (22:39 +0800)]
net: hns3: optimize the maximum TC macro
Multiple macros with the largest number of TCs in the system,
optimized to HCLGE_MAX_TC_NUM.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Sat, 2 Feb 2019 14:39:32 +0000 (22:39 +0800)]
net: hns3: fix a wrong checking in the hclge_tx_buffer_calc()
Only the TC is enabled, we need to check whether the buffer is enough,
otherwise it may lead to a wrong -ENOMEM case.
Fixes: 9ffe79a9c2ee ("net: hns3: Support for dynamically assigning tx buffer to TC") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Weihang Li [Sat, 2 Feb 2019 14:39:31 +0000 (22:39 +0800)]
net: hns3: move some set_bit statement into hclge_prepare_mac_addr
This patch does not change the code logic. There are some same
set_bit statements called by add/rm_uc/mc_addr_common, and move
this statements into hclge_prepare_mac_addr to reduce duplicate
code.
Signed-off-by: Weihang Li <liweihang@hisilicon.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Weihang Li [Sat, 2 Feb 2019 14:39:30 +0000 (22:39 +0800)]
net: hns3: add hclge_cmd_check_retval() to parse comman's return value
For simplifying the code, this patch adds hclge_cmd_check_retval() to
check the return value of the command.
Also, according the IMP's description, when there are several descriptors
in a command, then the IMP will save the return value on the last
description, so hclge_cmd_check_retval() just check the last one for this
case.
Signed-off-by: Weihang Li <liweihang@hisilicon.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Sat, 2 Feb 2019 14:39:29 +0000 (22:39 +0800)]
net: hns3: code optimization for hclge_rx_buffer_calc
There are four steps to calcuate the rx private buffer, each step
can be done in a function to avoid code duplication and aid code
readability.
This patch adds three separate functions do the job. Also, the
function name more or less make the comment redundant, so remove
some obvious comment.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yonglong Liu [Sat, 2 Feb 2019 14:39:28 +0000 (22:39 +0800)]
net: hns3: Modify parameter type from int to bool in set_gro_en
The second parameter to the hook function set_gro_en is always passed in
true/false, so modify it's type from int to bool.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Sat, 2 Feb 2019 14:39:27 +0000 (22:39 +0800)]
net: hns3: fix an issue for hns3_update_new_int_gl
HNS3 supports setting rx-usecs|tx-usecs as 0, but it will not
update dynamically when adaptive-tx or adaptive-rx is enable.
This patch removes the Redundant check.
Fixes: a95e1f8666e9 ("net: hns3: change the time interval of int_gl calculating") Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Sat, 2 Feb 2019 14:39:26 +0000 (22:39 +0800)]
net: hns3: fix a code style issue for hns3_update_new_int_gl()
Use the same code style for rx_group and tx_group in the
hns3_update_new_int_gl().
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For BPF_RSH | BPF_K, it could be implemented using NFP direct shift
instruction. For the other BPF_X shifts, NFP indirect shifts sequences need
to be used.
Separate code-gen hook is assigned to each instruction to make the
implementation clear.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Jiong Wang <jiong.wang@netronome.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Jiong Wang [Fri, 1 Feb 2019 22:39:28 +0000 (22:39 +0000)]
nfp: bpf: correct the behavior for shifts by zero
Shifts by zero do nothing, and should be treated as nops.
Even though compiler is not supposed to generate such instructions and
manual written assembly is unlikely to have them, but they are legal
instructions and have defined behavior.
This patch correct existing shifts code-gen to make sure they do nothing
when shift amount is zero except when the instruction is ALU32 for which
high bits need to be cleared.
For shift amount bigger than type size, already, NFP JIT back-end errors
out for immediate shift and only low 5 bits will be taken into account for
indirect shift which is the same as x86.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Jiong Wang <jiong.wang@netronome.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
====================
devlink: add device (driver) information API
fw_version field in ethtool -i does not suit modern needs with 31
characters being quite limiting on more complex systems. There is
also no distinction between the running and flashed versions of
the firmware.
Since the driver information pertains to the entire device, rather
than a particular netdev, it seems wise to move it do devlink, at
the same time fixing the aforementioned issues.
The new API allows exposing the device serial number and versions
of the components of the card - both hardware, firmware (running
and flashed). Driver authors can choose descriptive identifiers
for the version fields. A few version identifiers which seemed
relevant for most devices have been added to the global devlink
header.
Last patch also includes a compat code for ethtool. If driver
reports no fw_version via the traditional ethtool API, ethtool
can call into devlink and try to cram as many versions as possible
into the 31 characters.
v4:
- use IS_REACHABLE instead of IS_ENABLED in last patch.
v3 (Jiri):
- rename various functions and attributes;
- break out the version helpers per-type;
- make the compat code parse a dump instead of special casing
in each helper;
- move generic version defines to a separate patch.
v2:
- rebase.
this non-RFC, v3 some would say:
- add three more versions in the NFP patches;
- add last patch (ethool compat) - Andrew & Michal.
RFCv2:
- use one driver op;
- allow longer serial number;
- wrap the skb into an opaque request struct;
- add some common identifier into the devlink header.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 31 Jan 2019 18:50:47 +0000 (10:50 -0800)]
ethtool: add compat for devlink info
If driver did not fill the fw_version field, try to call into
the new devlink get_info op and collect the versions that way.
We assume ethtool was always reporting running versions.
v4:
- use IS_REACHABLE() to avoid problems with DEVLINK=m (kbuildbot).
v3 (Jiri):
- do a dump and then parse it instead of special handling;
- concatenate all versions (well, all that fit :)).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 31 Jan 2019 18:50:46 +0000 (10:50 -0800)]
nfp: devlink: report the running and flashed versions
Report versions of firmware components using the new NSP command.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 31 Jan 2019 18:50:44 +0000 (10:50 -0800)]
nfp: devlink: report fixed versions
Report information about the hardware.
RFCv2:
- add defines for board IDs which are likely to be reusable for
other drivers (Jiri).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 31 Jan 2019 18:50:43 +0000 (10:50 -0800)]
nfp: devlink: report driver name and serial number
Report the basic info through new devlink info API.
RFCv2:
- add driver name;
- align serial to core changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 31 Jan 2019 18:50:42 +0000 (10:50 -0800)]
devlink: add generic info version names
Add defines and docs for generic info versions.
v3:
- add docs;
- separate patch (Jiri).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 31 Jan 2019 18:50:41 +0000 (10:50 -0800)]
devlink: add version reporting to devlink info API
ethtool -i has a few fixed-size fields which can be used to report
firmware version and expansion ROM version. Unfortunately, modern
hardware has more firmware components. There is usually some
datapath microcode, management controller, PXE drivers, and a
CPLD load. Running ethtool -i on modern controllers reveals the
fact that vendors cram multiple values into firmware version field.
Here are some examples from systems I could lay my hands on quickly:
Add a new devlink API to allow retrieving multiple versions, and
provide user-readable name for those versions.
While at it break down the versions into three categories:
- fixed - this is the board/fixed component version, usually vendors
report information like the board version in the PCI VPD,
but it will benefit from naming and common API as well;
- running - this is the running firmware version;
- stored - this is firmware in the flash, after firmware update
this value will reflect the flashed version, while the
running version may only be updated after reboot.
v3:
- add per-type helpers instead of using the special argument (Jiri).
RFCv2:
- remove the nesting in attr DEVLINK_ATTR_INFO_VERSIONS (now
versions are mixed with other info attrs)l
- have the driver report versions from the same callback as
other info.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 31 Jan 2019 18:50:40 +0000 (10:50 -0800)]
devlink: add device information API
ethtool -i has served us well for a long time, but its showing
its limitations more and more. The device information should
also be reported per device not per-netdev.
Lay foundation for a simple devlink-based way of reading device
info. Add driver name and device serial number as initial pieces
of information exposed via this new API.
v3:
- rename helpers (Jiri);
- rename driver name attr (Jiri);
- remove double spacing in commit message (Jiri).
RFC v2:
- wrap the skb into an opaque structure (Jiri);
- allow the serial number of be any length (Jiri & Andrew);
- add driver name (Jonathan).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 1 Feb 2019 23:26:37 +0000 (15:26 -0800)]
Merge branch 'selftests-Various-fixes'
Petr Machata says:
====================
selftests: Various fixes
This patch set contains various fixes whose common denominator is
improving quality of forwarding and mlxsw selftests.
Most of the fixes are improvements in determinism (such that timing and
latency don't impact the test performance). These were prompted by
regular runs of the test suite on a hardware emulator, the performance
of which is necessarily lower than that of the real device.
Patches #1 (from Ido), #2 and #3 make changes to ping limits.
Patches #4 and #5 add more sleep in places where things need more time
to finish.
Patches #6 and #7 fix two tests in the suite of mirror-to-gretap tests
where underlay involves a VLAN device over an 802.1q bridge.
Patches #8, #9 and #10 fix bugs in mirror-to-gretap test where underlay
involves a LAG device.
Patch #11 fixes a missed RET initialization in mirror-to-gretap flower
test.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 31 Jan 2019 22:35:27 +0000 (22:35 +0000)]
selftests: forwarding: mirror_gre_flower: Fix test result handling
The global variable RET needs to be initialized before each call to
log_test. This test case sets it once before running the tests, but then
calls log_tests for every individual test. Thus a failure in one of the
tests causes spurious failures in follow-up tests as well.
Fix by moving the initialization of RET from test_all() to
full_test_span_gre_dir_acl(), a function that implements the test.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This test sets up mirroring such that it mirrors all overlay traffic.
That includes ARP, which causes occasional miscounts and spurious
failures. Ignore ARP explicitly to avoid these problems.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
After one LAG slave is downed and another upped, it takes a while for
the neighbor on a bridge to time out and get renegotiated. The test does
prompt update of FDB entries by arpinging. But because the neighbor
still references another address, offloading is not possible, and some
packets may end up not being mirrored.
To force the neighbor renegotiation, simply flush the neighbor table at
the bridge.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 31 Jan 2019 22:35:21 +0000 (22:35 +0000)]
selftests: forwarding: mirror_gre_vlan_bridge_1q: Fix roaming test
ARP or ND traffic can cause spurious migration of FDB back to $swp3.
Mirroring is then updated in accordance with the change, and mirrored
packets are seen at h3, causing a failure.
Detect the case of this spurious roaming, and retry the test.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 31 Jan 2019 22:35:18 +0000 (22:35 +0000)]
selftests: forwarding: mirror_gre_vlan_bridge_1q: Fix untagged test
The untagged egress test sets up mirroring to {,ip6}gretap such that the
underlay goes through a bridge. Then VLAN flags are manipulated to test
that the traffic leaves the bridge 802.1q-tagged or not, as appropriate.
However, when a neighbor expires at the time that the bridge VLAN is
configured as PVID and egress untagged, the following discovery process
can't finish, because the IP address on H3 is still at the VLAN-tagged
netdevice. This manifests by occasional failures where only several of
the 10 required packets get through.
Therefore, when reconfiguring the VLAN flags, move the IP address to the
appropriate device in the H3 VRF.
In addition to that, take this opportunity to embed an ASCII art diagram
to make the topology move obvious.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 31 Jan 2019 22:35:17 +0000 (22:35 +0000)]
selftests: forwarding: mirror_lib: Wait for tardy mirrored packets
When running in an environment with poor performance (such as a
simulator), processing mirrored packets can take a while. Evaluating the
condition too soon leads to spurious "seen 9, expected 10" failures as
the last packet doesn't have enough time to get mirrored and the mirror
to arrive and bump the observed counters.
Wait for one ping interval before evaluating the test.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 31 Jan 2019 22:35:15 +0000 (22:35 +0000)]
selftests: forwarding: mirror_gre_changes: Fix TTL test
When running in a simulator, the TTL change takes a while to settle and
during this time the performance of the packet processing is lowered.
The resulting instability leads to ping sending more packets as it
assumes some have been dropped. This then leads to regular spurious
failures as more packets than expected are observed.
Sleep a bit to give the system time to stabilize.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 31 Jan 2019 22:35:14 +0000 (22:35 +0000)]
selftests: mlxsw: Update ping limits
The current ping intervals are too short for running mirroring tests in
simulator. This leads to ping sending a follow-up ping before the reply
arrives, thus sending more than the requested 10 ICMP requests. This
traffic is seen at the counters, and causes spurious failures.
Bump interval and timeout numbers 5x in mirroring tests to address the
spurious failures.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The current ping intervals are too short for running mirroring tests in
simulator. This leads to ping sending a follow-up ping before the reply
arrives, thus sending more than the requested 10 ICMP requests. Those
are mirrored, and over a certain threshold the test case run is
considered a failure, because too much traffic is observed.
Bump interval and timeout numbers 5x in mirroring tests to address the
spurious failures.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 31 Jan 2019 22:35:10 +0000 (22:35 +0000)]
selftests: forwarding: Make ping timeout configurable
The current timeout (2 seconds) proved to be too low for some (emulated)
systems where we run the tests.
Make the timeout configurable and default to 5 seconds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
commit 3fb72f1e6e61 ("ipconfig wait for carrier") added a
"wait for carrier" policy, with a fixed worst case maximum wait
of two minutes.
Now make the wait for carrier timeout configurable on the kernel
commandline and use the 120s as the default.
The timeout messages introduced with
commit 5e404cd65860 ("ipconfig: add informative timeout messages while
waiting for carrier") are done in a fixed interval of 20 seconds, just
like they were before (240/12).
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / thirdparty / kernel / stable.git / log
