In commit 8a3b4c17f863 ("drm/msm/dp: employ bridge mechanism for display
enable and disable") the DP driver received a drm_bridge instance, which
is always attached to the encoder as a root bridge. However it conflicts
with the panel_bridge support for eDP panels. The panel bridge attaches
to the encoder before the "dp" bridge (DP driver's drm_bridge instance
created in msm_dp_bridge_init()) has a chance to do so. Change
panel bridge attachment to come after the "dp" bridge attachment (and to
use it as a previous bridge).
Fixes: 8a3b4c17f863 ("drm/msm/dp: employ bridge mechanism for display enable and disable") Cc: Kuogee Hsieh <quic_khsieh@quicinc.com> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20220211224006.1797846-2-dmitry.baryshkov@linaro.org
[db: fixed commit message according to Stephen's suggestions] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
DP audio enablement code which is comparing intf_type,
DRM_MODE_ENCODER_TMDS (= 2) with DRM_MODE_CONNECTOR_DisplayPort (= 10).
Which would never succeed. Fix it to check for DRM_MODE_ENCODER_TMDS.
Fixes: d13e36d7d222 ("drm/msm/dp: add audio support for Display Port on MSM") Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20220217035358.465904-2-dmitry.baryshkov@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The dsi_7nm_phy_enable() disagrees with downstream for
glbl_str_swi_cal_sel_ctrl and glbl_hstx_str_ctrl_0 values. Update
programmed settings to match downstream driver. To remove the
possibility for such errors in future drop less_than_1500_mhz
assignment and specify settings explicitly.
All DSI PHY/PLL drivers were referencing their VCO parent clock by a
global name, most of which don't exist or have been renamed. These
clock drivers seem to function fine without that except the 14nm driver
for sdm6xx [1].
At the same time all DTs provide a "ref" clock as per the requirements
of dsi-phy-common.yaml, but the clock is never used. This patchset puts
that clock to use without relying on a global clock name, so that all
dependencies are explicitly defined in DT (the firmware) in the end.
Note that this patch intentionally breaks older firmware (DT) that
relies on the clock to be found globally instead. The only affected
platform is msm8974 [2] for whose dsi_phy_28nm a .name="xo" fallback is
left in place to accommodate a more graceful transition period. All
other platforms had the "ref" clock added to their phy node since its
inception, or in a followup patch some time after. These patches
wrongly assumed that the "ref" clock was actively used and have hence
been listed as "Fixes:" below.
Furthermore apq8064 was providing the wrong 19.2MHz cxo instead of
27MHz pxo clock, which has been addressed in [3].
It is expected that both [2] and [3] are applied to the tree well in
advance of this patch such that any actual breakage is extremely
unlikely, but might still occur if kernel upgrades are performed without
the DT to match. After some time the fallback for msm8974 can be
removed again as well.
Fixes: 79e51645a1dd ("arm64: dts: qcom: msm8916: Set 'xo_board' as ref clock of the DSI PHY") Fixes: 6969d1d9c615 ("ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY") Fixes: 0c0e72705a33 ("arm64: dts: sdm845: Set 'bi_tcxo' as ref clock of the DSI PHYs") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210911131922.387964-2-marijn.suijten@somainline.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some of DP link compliant test expects to return fail-safe mode
if prefer detailed timing mode can not be supported by mainlink's
lane and rate after link training. Therefore add fail-safe mode
into connector mode list as backup mode. This patch fixes test
case 4.2.2.1.
Changes in v2:
-- add Fixes text string
Fixes: 4b85d405cfe9 ( "drm/msm/dp: reduce link rate if failed at link training 1") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1643066274-25814-1-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Each DP link training contains link training 1 followed by link
training 2. There is maximum of 5 retries of DP link training
before declared link training failed. It is required to stop link
training at end of link training 2 if it is failed so that next
link training 1 can start freshly. This patch fixes link compliance
test case 4.3.1.13 (Source Device Link Training EQ Fallback Test).
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read
Fixes: 2e0adc765d88 ("drm/msm/dp: do not end dp link training until video is ready") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-5-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
DP CTS test case 4.2.2.6 has valid edid with bad checksum on purpose
and expect DP source return correct checksum. During drm edid read,
correct edid checksum is calculated and stored at
connector::real_edid_checksum.
The problem is struct dp_panel::connector never be assigned, instead the
connector is stored in struct msm_dp::connector. When we run compliance
testing test case 4.2.2.6 dp_panel_handle_sink_request() won't have a valid
edid set in struct dp_panel::edid so we'll try to use the connectors
real_edid_checksum and hit a NULL pointer dereference error because the
connector pointer is never assigned.
Changes in V2:
-- populate panel connector at msm_dp_modeset_init() instead of at dp_panel_read_sink_caps()
Changes in V3:
-- remove unhelpful kernel crash trace commit text
-- remove renaming dp_display parameter to dp
Changes in V4:
-- add more details to commit text
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read
Current DP drivers have regulators, clocks, irq and phy are grouped
together within a function and executed not in a symmetric manner.
This increase difficulty of code maintenance and limited code scalability.
This patch divides the driver life cycle of operation into four states,
resume (including booting up), dongle plugin, dongle unplugged and suspend.
Regulators, core clocks and irq are grouped together and enabled at resume
(or booting up) so that the DP controller is armed and ready to receive HPD
plugin interrupts. HPD plugin interrupt is generated when a dongle plugs
into DUT (device under test). Once HPD plugin interrupt is received, DP
controller will initialize phy so that dpcd read/write will function and
following link training can be proceeded successfully. DP phy will be
disabled after main link is teared down at end of unplugged HPD interrupt
handle triggered by dongle unplugged out of DUT. Finally regulators, code
clocks and irq are disabled at corresponding suspension.
Changes in V2:
-- removed unnecessary dp_ctrl NULL check
-- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs
-- remove flip parameter out of dp_ctrl_irq_enable()
-- add fixes tag
Changes in V3:
-- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at
dp_display_host_init() for eDP
Changes in V4:
-- rewording commit text to match this commit changes
Changes in V5:
-- rebase on top of msm-next branch
Changes in V6:
-- delete flip variable
Changes in V7:
-- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl()
Changes in V8:
-- add more detail comment regrading dp phy at dp_display_host_init()
Changes in V9:
-- remove set phy_initialized to false when -ECONNRESET detected
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately
if aux read
Changes in v12:
-- move dp_display_host_phy_exit() after dp_display_host_deinit()
Changes in v13:
-- do not execute phy_init until plugged_in interrupt for edp, same as DP.
Changes in v14:
-- remove redundant dp->core_initialized = false form dp_pm_suspend.
Changes in v15:
-- remove core_initialized flag check at both host_init and host_deinit
Changes in v16:
-- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend
Changes in v17:
-- remove core_initialized checking before execute attention_cb()
Changes in v18:
-- remove core_initialized checking at dp_pm_suspend
In devicetree the flash information is embedded within nand chip node,
so during nand chip initialization the nand chip node should be passed
to nand_set_flash_node() api, instead of nand controller node.
Fixes: 08d8c62164a3 ("mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller") Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220209053427.27676-1-amit.kumar-mahapatra@xilinx.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the error -EIO is being assinged to variable ret when
the READY_BIT is not set but the function iwlagn_mac_start returns
0 rather than ret. Fix this by returning ret instead of 0.
Addresses-Coverity: ("Unused value") Fixes: 7335613ae27a ("iwlwifi: move all mac80211 related functions to one place") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210907104658.14706-1-colin.king@canonical.com Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The config set TLV setting depend on dram allocation
and if allocation failed the data used in config set tlv
should not set this.
Adding the check if dram fragment is available or not.
Due to preg protection we cannot write to this register
while FW is running (when FW in Halt it is ok).
since we have some cases that we need to dump this
region while FW is running remove this writing from DRV.
FW will do this writing.
Since commit a05829a7222e ("cfg80211: avoid holding the RTNL when
calling the driver") we're not only holding the RTNL when going
in and out of suspend, but also the wiphy->mtx. Add that to the
D3 test debugfs in iwlwifi since it's required for various calls
to mac80211.
Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20220129105618.fcec0204e162.Ib73bf787ab4d83581de20eb89b1f8dbfcaaad0e3@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We may not have all the interfaces added to the driver when we get the
THERMAL_DUAL_CHAIN_REQUEST notification from the FW, so instead of
iterating all vifs to update SMPS, iterate only the ones that are
already assigned. The interfaces that were not assigned yet, will be
updated accordingly when we start using them.
The recent fix for NULL sta in iwl_mvm_get_tx_rate() still has a call
of iwl_mvm_sta_from_mac80211() that may be called with NULL sta.
Although this practically only points to the address and the actual
access doesn't happen due to the conditional evaluation at a later
point, it looks a bit flaky.
This patch drops the temporary variable above and evaluates
iwm_mvm_sta_from_mac80211() directly for avoiding confusions.
This patch added the data checksum error mib counters check for the
script mptcp_connect.sh when the data checksum is enabled.
In do_transfer(), got the mib counters twice, before and after running
the mptcp_connect commands. The latter minus the former is the actual
number of the data checksum mib counter.
The output looks like this:
ns1 MPTCP -> ns2 (dead:beef:1::2:10007) MPTCP (duration 86ms) [ OK ]
ns1 MPTCP -> ns2 (10.0.2.1:10008 ) MPTCP (duration 66ms) [ FAIL ]
server got 1 data checksum error[s]
Fixes: 94d66ba1d8e48 ("selftests: mptcp: enable checksum in mptcp_connect.sh") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/255 Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is caused by dax_fs_exit() not flushing inodes before destroy cache.
To fix this issue, call rcu_barrier() before destroy cache.
Signed-off-by: Tong Zhang <ztong0001@gmail.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220212071111.148575-1-ztong0001@gmail.com Fixes: 7b6be8444e0f ("dax: refactor dax-fs into a generic provider of 'struct dax_device' instances") Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
KASAN + DEBUG_KOBJECT_RELEASE reports a potential use-after-free in
cxl_decoder_release() where it goes to reference its parent, a cxl_port,
to free its id back to port->decoder_ida.
BUG: KASAN: use-after-free in to_cxl_port+0x18/0x90 [cxl_core]
Read of size 8 at addr ffff888119270908 by task kworker/35:2/379
The device core only guarantees parent lifetime until all children are
unregistered. If a child needs a parent to complete its ->release()
callback that child needs to hold a reference to extend the lifetime of
the parent.
Fixes: 40ba17afdfab ("cxl/acpi: Introduce cxl_decoder objects") Reported-by: Ben Widawsky <ben.widawsky@intel.com> Tested-by: Ben Widawsky <ben.widawsky@intel.com> Reviewed-by: Ben Widawsky <ben.widawsky@intel.com> Link: https://lore.kernel.org/r/164505751190.4175768.13324905271463416712.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
When display topology changed on DSC hub we add all crtcs with dsc support to
atomic state.
Refer to patch:"drm/amd/display: Trigger modesets on MST DSC connectors"
However the original implementation may skip crtc if the topology change
caused by unplug.
That potentially could lead to no-lightup or corruption on DSC hub after
unplug event on one of the connectors.
[How]
Update add_affected_mst_dsc_crtcs() to use old connector state
if new connector state has no crtc (undergoes modeset due to unplug)
Fixes: 44be939ff7ac58 ("drm/amd/display: Trigger modesets on MST DSC connectors") Reviewed-by: Hersen Wu <hersenwu@amd.com> Acked-by: Jasdeep Dhillon <jdhillon@amd.com> Signed-off-by: Roman Li <Roman.Li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
pm sysfs should be writable in one VF mode as is in passthrough
[how]
do not remove write access on pm sysfs if device is in one VF mode
Fixes: 11c9cc95f818 ("amdgpu/pm: Make sysfs pm attributes as read-only for VFs") Signed-off-by: Yiqing Yao <yiqing.yao@amd.com> Reviewed-by: Monk Liu <Monk.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When reworking btf__get_from_id() in commit a19f93cfafdf the error
handling when calling bpf_btf_get_fd_by_id() changed. Before the rework
if bpf_btf_get_fd_by_id() failed the error would not be propagated to
callers of btf__get_from_id(), after the rework it is. This lead to a
change in behavior in print_key_value() that now prints an error when
trying to lookup keys in maps with no btf available.
Fix this by following the way used in dumping maps to allow to look up
keys in no-btf maps, by which it decides whether and where to get the
btf info according to the btf value type.
Fixes: a19f93cfafdf ("libbpf: Add internal helper to load BTF data by FD") Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Link: https://lore.kernel.org/bpf/1644249625-22479-1-git-send-email-yinjun.zhang@corigine.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Drop I2C device-probing classes from platform variant of the PASemi
controller as it is only used on platforms where I2C devices should
be instantiated in devicetree. (The I2C_CLASS_DEPRECATED flag is not
raised as up to this point no devices relied on the old behavior.)
Fixes: d88ae2932df0 ("i2c: pasemi: Add Apple platform driver") Signed-off-by: Martin Povišer <povik+lin@cutebit.org> Reviewed-by: Sven Peter <sven@svenpeter.dev> Acked-by: Hector Martin <marcan@marcan.st> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 1b8bb94c0612 ("ath11k: report tx bitrate for iw wlan station dump") Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220209060816.423-1-quic_wgong@quicinc.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
Internally kernel prepends all report buffers, for both numbered and
unnumbered reports, with report ID, therefore to properly handle unnumbered
reports we should prepend it ourselves.
For the same reason we should skip the first byte of the buffer when
calling i2c_hid_set_or_send_report() which then will take care of properly
formatting the transfer buffer based on its separate report ID argument
along with report payload.
[jkosina@suse.cz: finalize trimmed sentence in changelog as spotted by Benjamin] Fixes: 9b5a9ae88573 ("HID: i2c-hid: implement ll_driver transport-layer callbacks") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
When receiving netlink messages, libbpf was using a statically allocated
stack buffer of 4k bytes. This happened to work fine on systems with a 4k
page size, but on systems with larger page sizes it can lead to truncated
messages. The user-visible impact of this was that libbpf would insist no
XDP program was attached to some interfaces because that bit of the netlink
message got chopped off.
Fix this by switching to a dynamically allocated buffer; we borrow the
approach from iproute2 of using recvmsg() with MSG_PEEK|MSG_TRUNC to get
the actual size of the pending message before receiving it, adjusting the
buffer as necessary. While we're at it, also add retries on interrupted
system calls around the recvmsg() call.
v2:
- Move peek logic to libbpf_netlink_recv(), don't double free on ENOMEM.
When the dw-hdmi bridge is in first place of the bridge chain, this
means there is no way to select an input format of the dw-hdmi HW
component.
Since introduction of display-connector, negotiation was broken since
the dw-hdmi negotiation code only worked when the dw-hdmi bridge was
in last position of the bridge chain or behind another bridge also
supporting input & output format negotiation.
Commit 7cd70656d128 ("drm/bridge: display-connector: implement bus fmts callbacks")
was introduced to make negotiation work again by making display-connector
act as a pass-through concerning input & output format negotiation.
But in the case where the dw-hdmi is single in the bridge chain, for
example on Renesas SoCs, with the display-connector bridge the dw-hdmi
is no more single, breaking output format.
Reported-by: Biju Das <biju.das.jz@bp.renesas.com> Bisected-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Fixes: 6c3c719936da ("drm/bridge: synopsys: dw-hdmi: add bus format negociation") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: add proper fixes commit] Reviewed-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220204143337.89221-1-narmstrong@baylibre.com Signed-off-by: Sasha Levin <sashal@kernel.org>
netvsc_device_remove() calls vunmap() inside which should not be
called in the interrupt context. Current code calls hv_unmap_memory()
in the free_netvsc_device() which is rcu callback and maybe called
in the interrupt context. This will trigger BUG_ON(in_interrupt())
in the vunmap(). Fix it via moving hv_unmap_memory() to netvsc_device_
remove().
Fixes: 846da38de0e8 ("net: netvsc: Add Isolation VM support for netvsc driver") Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In CXL 2.0, 8.2.5.1 CXL Capability Header Register: this register
is given as 32 bits.
8.2.3 which covers the CXL 2.0 Component registers, including the
CXL Capability Header Register states that access restrictions
specified in Section 8.2.2 apply.
8.2.2 includes:
* A 32 bit register shall be accessed as a 4 Byte quantity.
...
If these rules are not followed, the behavior is undefined.
Fixing that, led to this code failing. Whilst a given hardware
implementation 'might' work with an 8 byte read, it should not be relied
upon. The QEMU emulation v5 will return 0 and log the wrong access width.
The code moved, so one fixes tag for where this will directly apply and
also a reference to the earlier introduction of the code for backports.
riscv registers are accessed via struct user_regs_struct, not struct
pt_regs. The program counter member in this struct is called pc, not
epc. The frame pointer is called s0, not fp.
It's wrong to check the last packet by RXE_COMP_MASK because the flag is
to indicate if responder needs to generate a completion.
Fixes: 9fcd67d1772c ("IB/rxe: increment msn only when completing a request") Fixes: 8700e3e7c485 ("Soft RoCE driver") Link: https://lore.kernel.org/r/20211229034438.1854908-1-yangx.jy@fujitsu.com Signed-off-by: Xiao Yang <yangx.jy@fujitsu.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The emulated bridge returns incorrect value for PCI_EXP_RTSTA register
during readout in advk_pci_bridge_emul_pcie_conf_read() function: the
correct bit is BIT(16), but we are setting BIT(23), because the code
does
*value = (isr0 & PCIE_MSG_PM_PME_MASK) << 16
where
PCIE_MSG_PM_PME_MASK
is
BIT(7).
The code should probably have been something like
*value = (!!(isr0 & PCIE_MSG_PM_PME_MASK)) << 16,
but we are better of using an if() and using the proper macro for this
bit.
In advk_pcie_handle_msi() it is expected that when bit i in the W1C
register PCIE_MSI_STATUS_REG is cleared, the PCIE_MSI_PAYLOAD_REG is
updated to contain the MSI number corresponding to index i.
Experiments show that this is not so, and instead PCIE_MSI_PAYLOAD_REG
always contains the number of the last received MSI, overall.
Do not read PCIE_MSI_PAYLOAD_REG register for determining MSI interrupt
number. Since Aardvark already forbids more than 32 interrupts and uses
own allocated hwirq numbers, the msi_idx already corresponds to the
received MSI number.
On changing the RX ring parameters igb uses a hack to avoid a warning
when calling xdp_rxq_info_reg via igb_setup_rx_resources. It just
clears the struct xdp_rxq_info content.
Instead, change this to unregister if we're already registered. Align
code to the igc code.
igc_ethtool_set_ringparam() copies the igc_ring structure but neglects to
reset the xdp_rxq_info member before calling igc_setup_rx_resources().
This in turn calls xdp_rxq_info_reg() with an already registered xdp_rxq_info.
Make sure to unregister the xdp_rxq_info structure first in
igc_setup_rx_resources.
Fixes: 73f1071c1d29 ("igc: Add support for XDP_TX action") Reported-by: Lennert Buytenhek <buytenh@arista.com> Signed-off-by: Corinna Vinschen <vinschen@redhat.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On architectures that don't use a syscall wrapper, sys_* function names
are set as an alias of __se_sys_* functions. Due to this, there is no
BTF associated with sys_* function names. This results in some of the
test progs failing to load. Set the SYS_PREFIX to "__se_" to fix this
issue.
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e2166 ("spi: Revert modalias changes") Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Michael Walle <michael@walle.cc> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220202143404.16070-4-broonie@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e2166 ("spi: Revert modalias changes") Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Michael Walle <michael@walle.cc> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220202143404.16070-3-broonie@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Some resource should be released if an error occurs in
'bcm2835_i2c_probe()'.
Add an error handling path and the needed 'clk_disable_unprepare()' and
'clk_rate_exclusive_put()' calls.
While at it, rework the bottom of the function to use this newly added
error handling path and have an explicit and more standard "return 0;" at
the end of the normal path.
Fixes: bebff81fb8b9 ("i2c: bcm2835: Model Divider in CCF") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[wsa: rebased] Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot once again hit uninit value in asix driver. The problem still the
same -- asix_read_cmd() reads less bytes, than was requested by caller.
Since all read requests are performed via asix_read_cmd() let's catch
usb related error there and add __must_check notation to be sure all
callers actually check return value.
So, this patch adds sanity check inside asix_read_cmd(), that simply
checks if bytes read are not less, than was requested and adds missing
error handling of asix_read_cmd() all across the driver code.
Fixes: d9fe64e51114 ("net: asix: Add in_pm parameter") Reported-and-tested-by: syzbot+6ca9f7867b77c2d316ac@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Running with POSIXLY_CORRECT=1 in the environment the scripts/dtc build
fails, because pkg-config doesn't output anything when the flags come
after the arguments.
Fixes: 067c650c456e ("dtc: Use pkg-config to locate libyaml") Signed-off-by: Thomas Bracht Laumann Jespersen <t@laumann.xyz> Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20220131112028.7907-1-t@laumann.xyz Signed-off-by: Sasha Levin <sashal@kernel.org>
If we're limiting bandwidth for some reason such as regulatory
restrictions, then advertise that limitation just like we do
for VHT today, so the AP is aware we cannot use the higher BW
it might be using.
The kasan error is triggered with an illegal BTF like below:
type 0: void
type 1: int
type 2: decl_tag to func type 3
type 3: func to func_proto type 8
The total number of types is 4 and the type 3 is illegal
since its func_proto type is out of range.
Currently, the target type of decl_tag can be struct/union, var or func.
Both struct/union and var implemented their own 'resolve' callback functions
and hence handled properly in kernel.
But func type doesn't have 'resolve' callback function. When
btf_decl_tag_resolve() tries to check func type, it tries to get
vlen of its func_proto type, which triggered the above kasan error.
To fix the issue, btf_decl_tag_resolve() needs to do btf_func_check()
before trying to accessing func_proto type.
In the current implementation, func type is checked with
btf_func_check() in the main checking function btf_check_all_types().
To fix the above kasan issue, let us implement 'resolve' callback
func type properly. The 'resolve' callback will be also called
in btf_check_all_types() for func types.
Fixes: b5ea834dde6b ("bpf: Support for new btf kind BTF_KIND_TAG") Reported-by: syzbot+53619be9444215e785ed@syzkaller.appspotmail.com Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/20220203191727.741862-1-yhs@fb.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 73f37068d540 ("ptp: support ptp physical/virtual clocks conversion") Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Cc: Yangbo Lu <yangbo.lu@nxp.com> Cc: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Always release fw data at the end of mt7921_load_patch routine.
Fixes: 78b217580c509 ("mt76: mt7921s: fix bus hang with wrong privilege") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
It doesn't guarantee the mt7921e gets started with ASPM L0 after each
machine reboot on every platform.
If mt7921e gets started with not ASPM L0, it would be possible that the
driver encounters time to time failure in mt7921_pci_probe, like a
weird chip identifier is read
[ 215.514503] mt7921e 0000:05:00.0: ASIC revision: feed0000
[ 216.604741] mt7921e: probe of 0000:05:00.0 failed with error -110
or failing to init hardware because the driver is not allowed to access the
register until the device is in ASPM L0 state. So, we call
__mt7921e_mcu_drv_pmctrl in early mt7921_pci_probe to force the device
to bring back to the L0 state for we can safely access registers in any
case.
In the patch, we move all functions from dma.c to pci.c and register mt76
bus operation earilier, that is the __mt7921e_mcu_drv_pmctrl depends on.
Fixes: bf3747ae2e25 ("mt76: mt7921: enable aspm by default") Reported-by: Kai-Chuan Hsieh <kaichuan.hsieh@canonical.com> Co-developed-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the firmware behavior (even the oldest one in linux-firmware)
If the firmware is downloaded, MT7921S must rely on the additional mailbox
mechanism that resides in firmware to check if the device is the right
state for mt7921s_mcu_[fw|drv]_pmctrl. Otherwise, we still apply the old
way for that.
That is a necessary patch before we enable runtime pm for mt7921s as
default.
Fixes: 48fab5bbef40 ("mt76: mt7921: introduce mt7921s support") Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Leon Yen <leon.yen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 'd430dffbe9dd ("mt76: mt7921: fix a possible race
enabling/disabling runtime-pm")', runtime-pm is always disabled in the
fw even if the user requests to enable it toggling debugfs node since
mt7921_pm_interface_iter routine will use pm->enable to configure the fw.
Fix the issue moving enable variable configuration before running
mt7921_pm_interface_iter routine.
Fixes: d430dffbe9dd ("mt76: mt7921: fix a possible race enabling/disabling runtime-pm") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
The command MCU_EXT_CMD_EDCA_UPDATE is not fully supported by the MT7921
firmware, so we apply CE command MCU_CE_CMD_SET_EDCA_PARAMS instead which
is supported even in the oldest firmware to properly set up EDCA parameters
for each AC.
Fixes: 1c099ab44727 ("mt76: mt7921: add MCU support") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
mac80211 provides aid in vif->bss_conf.aid for sta mode and not in
sta->aid. Fix mt7915_mcu_wtbl_generic_tlv routine using proper value for
aid in sta mode.
Fixes: e57b7901469fc ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Trace IMC (In-Memory collection counters) in powerpc is useful for
application level profiling.
For trace_imc, presently task context (task_ctx_nr) is set to
perf_hw_context. But perf_hw_context should only be used for CPU PMU.
See commit 26657848502b ("perf/core: Verify we have a single
perf_hw_context PMU").
So for trace_imc, even though it is per thread PMU, it is preferred to
use sw_context in order to be able to do application level monitoring.
Hence change the task_ctx_nr to use perf_sw_context.
On board rev A, the network interface labels for the switch ports
written on the front panel are different than on rev B and later.
This patch fixes network interface names for the switch ports according
to labels that are written on the front panel of the board rev B.
They start from ETH3 and end at ETH10.
This patch also introduces a separate device tree for rev A.
The main device tree is supposed to cover rev B and later.
As the possible failure of the ioremap(), the 'local->sram' and other
two could be NULL.
Therefore it should be better to check it in order to avoid the later
dev_dbg.
For now, if the XDP prog returns XDP_PASS on XSK, the metadata
will be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
net_prefetch() xdp->data_meta and align the copy size to speed-up
memcpy() a little and better match ixgbe_construct_skb().
Fixes: d0bcacd0a130 ("ixgbe: add AF_XDP zero-copy Rx support") Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com> Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, ixgbe_construct_skb_zc() currently allocates and reserves
additional `xdp->data - xdp->data_hard_start`, which is
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only to __napi_alloc_skb() and
don't reserve anything. This will give enough headroom for stack
processing.
Fixes: d0bcacd0a130 ("ixgbe: add AF_XDP zero-copy Rx support") Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
To not dereference bi->xdp each time in ixgbe_construct_skb_zc(),
pass bi->xdp as an argument instead of bi. We can also call
xsk_buff_free() outside of the function as well as assign bi->xdp
to NULL, which seems to make it closer to its name.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, igc_construct_skb_zc() currently allocates and reserves
additional `xdp->data_meta - xdp->data_hard_start`, which is about
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only (+ meta) to
__napi_alloc_skb() and don't reserve anything. This will give
enough headroom for stack processing.
Also, net_prefetch() xdp->data_meta and align the copy size to
speed-up memcpy() a little and better match igc_construct_skb().
Fixes: fc9df2a0b520 ("igc: Enable RX via AF_XDP zero-copy") Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For now, if the XDP prog returns XDP_PASS on XSK, the metadata will
be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
net_prefetch() xdp->data_meta and align the copy size to speed-up
memcpy() a little and better match ice_construct_skb().
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com> Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, ice_construct_skb_zc() currently allocates and reserves
additional `xdp->data - xdp->data_hard_start`, which is
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only to __napi_alloc_skb() and
don't reserve anything. This will give enough headroom for stack
processing.
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For now, if the XDP prog returns XDP_PASS on XSK, the metadata will
be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
net_prefetch() xdp->data_meta and align the copy size to speed-up
memcpy() a little and better match i40e_construct_skb().
Fixes: 0a714186d3c0 ("i40e: add AF_XDP zero-copy Rx support") Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com> Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, i40e_construct_skb_zc() currently allocates and reserves
additional `xdp->data - xdp->data_hard_start`, which is
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only to __napi_alloc_skb() and
don't reserve anything. This will give enough headroom for stack
processing.
Previously we allocated less memory than actual required, overwrite
to the buffer causes the mm module to complaint and raise access
violation faults. Along with potential memory leaks when returned
early. Fix these by passing the correct size and proper deinit flow.
Upon hw scan completion, idle mode is not re-entered. This might
increase power consumption under no link mode. Fix this by adding the
re-enter flow. We need another work for this since enter_ips waits
for c2h_work to finish, which might lead to deadlock if caller is in
the same work.
projects / thirdparty / kernel / stable.git / log
