The controller will always generate a completion interrupt when the
transfer is finished normally or not. Currently we use either error or
completion interrupt to finish, this may result the completion
interrupt unhandled and corrupt the next transfer, especially at low
speed mode. Since on error case, the error interrupt will come first
then is the completion interrupt. So only use the completion interrupt
to finish the whole transfer process.
Fixes: d62fbdb99a85 ("i2c: add support for HiSilicon I2C controller") Reported-by: Sheng Feng <fengsheng5@huawei.com> Signed-off-by: Sheng Feng <fengsheng5@huawei.com> Signed-off-by: Yicong Yang <yangyicong@hisilicon.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When reading from I2C, the Tx watermark is set to 0. Unfortunately the
TDF (transmit data flag) is enabled when Tx FIFO entries is equal or less
than watermark. So it is set in every case, hence the reset default of 1.
This results in the MSR_RDF _and_ MSR_TDF flags to be set thus trying
to send Tx data on a read message.
Mask the IRQ status to filter for wanted flags only.
Fixes: a55fa9d0e42e ("i2c: imx-lpi2c: add low power i2c bus driver") Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The check introduced in the commit a5fd39464a40 ("igc: Lift TAPRIO schedule
restriction") can detect a false positive error in some corner case.
For instance,
tc qdisc replace ... taprio num_tc 4
...
sched-entry S 0x01 100000 # slot#1
sched-entry S 0x03 100000 # slot#2
sched-entry S 0x04 100000 # slot#3
sched-entry S 0x08 200000 # slot#4
flags 0x02 # hardware offload
Here the queue#0 (the first queue) is on at the slot#1 and #2,
and off at the slot#3 and #4. Under the current logic, when the slot#4
is examined, validate_schedule() returns *false* since the enablement
count for the queue#0 is two and it is already off at the previous slot
(i.e. #3). But this definition is truely correct.
Let's fix the logic to enforce a strict validation for consecutively-opened
slots.
Fixes: a5fd39464a40 ("igc: Lift TAPRIO schedule restriction") Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
vf reset nack actually represents the reset operation itself is
performed but no address is assigned. Therefore, e1000_reset_hw_vf
should fill the "perm_addr" with the zero address and return success on
such an occasion. This prevents its callers in netdev.c from saying PF
still resetting, and instead allows them to correctly report that no
address is assigned.
Fixes: 6ddbc4cf1f4d ("igb: Indicate failure on vf reset for empty mac address") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Tested-by: Marek Szlosek <marek.szlosek@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In igbvf_request_msix(), irqs have not been freed on the err path,
we need to free it. Fix it.
Fixes: d4e0fe01a38a ("igbvf: add new driver to support 82576 virtual functions") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Marek Szlosek <marek.szlosek@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, IAVF's decode_rx_desc_ptype() correctly reports payload type
of L4 for IPv4 UDP packets and IPv{4,6} TCP, but only L3 for IPv6 UDP.
Originally, i40e, ice and iavf were affected.
Commit 73df8c9e3e3d ("i40e: Correct UDP packet header for non_tunnel-ipv6")
fixed that in i40e, then
commit 638a0c8c8861 ("ice: fix incorrect payload indicator on PTYPE")
fixed that for ice.
IPv6 UDP is L4 obviously. Fix it and make iavf report correct L4 hash
type for such packets, so that the stack won't calculate it on CPU when
needs it.
Fixes: 206812b5fccb ("i40e/i40evf: i40e implementation for skb_set_hash") Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Condition, which checks whether the netdev has hashing enabled is
inverted. Basically, the tagged commit effectively disabled passing flow
hash from descriptor to skb, unless user *disables* it via Ethtool.
Commit a876c3ba59a6 ("i40e/i40evf: properly report Rx packet hash")
fixed this problem, but only for i40e.
Invert the condition now in iavf and unblock passing hash to skbs again.
Fixes: 857942fd1aa1 ("i40e: Fix Rx hash reported to the stack by our driver") Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: c1a281e34dae ("power: Add support for DA9150 Charger") Signed-off-by: Zheng Wang <zyytlz.wz@163.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In bq24190_probe, &bdi->input_current_limit_work is bound
with bq24190_input_current_limit_work. When external power
changed, it will call bq24190_charger_external_power_changed
to start the work.
If we remove the module which will call bq24190_remove to make
cleanup, there may be a unfinished work. The possible
sequence is as follows:
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Stable-dep-of: 47c29d692129 ("power: supply: bq24190: Fix use after free bug in bq24190_remove due to race condition") Signed-off-by: Sasha Levin <sashal@kernel.org>
ctx->crypto_send.info is not protected by lock_sock in
do_tls_getsockopt_conf(). A race condition between do_tls_getsockopt_conf()
and error paths of do_tls_setsockopt_conf() may lead to a use-after-free
or null-deref.
More discussion: https://lore.kernel.org/all/Y/ht6gQL+u6fj3dG@hog/
To fix the issue, check if the hwlatd thread for the cpu is already
running, before starting a new one. Along with the previous patch, this
avoids running multiple instances of the same CPU thread on the system.
Add a new helper function kthread_run_on_cpu(), which includes
kthread_create_on_cpu/wake_up_process().
In some cases, use kthread_run_on_cpu() directly instead of
kthread_create_on_node/kthread_bind/wake_up_process() or
kthread_create_on_cpu/wake_up_process() or
kthreadd_create/kthread_bind/wake_up_process() to simplify the code.
[akpm@linux-foundation.org: export kthread_create_on_cpu to modules]
Link: https://lkml.kernel.org/r/20211022025711.3673-2-caihuoqing@baidu.com Signed-off-by: Cai Huoqing <caihuoqing@baidu.com> Cc: Bernard Metzler <bmt@zurich.ibm.com> Cc: Cai Huoqing <caihuoqing@baidu.com> Cc: Daniel Bristot de Oliveira <bristot@kernel.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Doug Ledford <dledford@redhat.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: "Paul E . McKenney" <paulmck@kernel.org> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stable-dep-of: 08697bca9bbb ("trace/hwlat: Do not start per-cpu thread if it is already running") Signed-off-by: Sasha Levin <sashal@kernel.org>
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
The Aspeed Virtual UART is only present on Aspeed BMC platforms. Hence
add a dependency on ARCH_ASPEED, to prevent asking the user about this
driver when configuring a kernel without Aspeed BMC support.
When the timer fires a bit later, sport->dma_rx_desc is NULL:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
pc : lpuart_copy_rx_to_tty+0xcc/0x5bc
lr : lpuart_timer_func+0x1c/0x2c
Call trace:
lpuart_copy_rx_to_tty
lpuart_timer_func
call_timer_fn
__run_timers.part.0
run_timer_softirq
__do_softirq
__irq_exit_rcu
irq_exit
handle_domain_irq
gic_handle_irq
call_on_irq_stack
do_interrupt_handler
...
To fix this fold del_timer_sync() into lpuart_dma_rx_free() after
dmaengine_terminate_sync() to make sure timer will not be re-started in
lpuart_copy_rx_to_tty() <= lpuart_dma_rx_complete().
There is a problem with the behavior of hwlat in a container,
resulting in incorrect output. A warning message is generated:
"cpumask changed while in round-robin mode, switching to mode none",
and the tracing_cpumask is ignored. This issue arises because
the kernel thread, hwlatd, is not a part of the container, and
the function sched_setaffinity is unable to locate it using its PID.
Additionally, the task_struct of hwlatd is already known.
Ultimately, the function set_cpus_allowed_ptr achieves
the same outcome as sched_setaffinity, but employs task_struct
instead of PID.
Time readers rely on perf_event_context->[time|timestamp|timeoffset] to get
accurate time_enabled and time_running for an event. The difference between
ctx->timestamp and ctx->time is the among of time when the context is not
enabled. __update_context_time(ctx, false) is used to increase timestamp,
but not time. Therefore, it should only be called in ctx_sched_in() when
EVENT_TIME was not enabled.
Fixes: 09f5e7dc7ad7 ("perf: Fix perf_event_read_local() time") Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/r/20230313171608.298734-1-song@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
syzkaller reportes a KASAN issue with stack-out-of-bounds.
The call trace is as follows:
dump_stack+0x9c/0xd3
print_address_description.constprop.0+0x19/0x170
__kasan_report.cold+0x6c/0x84
kasan_report+0x3a/0x50
__perf_event_header__init_id+0x34/0x290
perf_event_header__init_id+0x48/0x60
perf_output_begin+0x4a4/0x560
perf_event_bpf_output+0x161/0x1e0
perf_iterate_sb_cpu+0x29e/0x340
perf_iterate_sb+0x4c/0xc0
perf_event_bpf_event+0x194/0x2c0
__bpf_prog_put.constprop.0+0x55/0xf0
__cls_bpf_delete_prog+0xea/0x120 [cls_bpf]
cls_bpf_delete_prog_work+0x1c/0x30 [cls_bpf]
process_one_work+0x3c2/0x730
worker_thread+0x93/0x650
kthread+0x1b8/0x210
ret_from_fork+0x1f/0x30
commit 267fb27352b6 ("perf: Reduce stack usage of perf_output_begin()")
use on-stack struct perf_sample_data of the caller function.
However, perf_event_bpf_output uses incorrect parameter to convert
small-sized data (struct perf_bpf_event) into large-sized data
(struct perf_sample_data), which causes memory overwriting occurs in
__perf_event_header__init_id.
Fixes: 267fb27352b6 ("perf: Reduce stack usage of perf_output_begin()") Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20230314044735.56551-1-yangjihong1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Events should only be added to a groups rb tree if they have not been
removed from their context by list_del_event(). Since remove_on_exec
made it possible to call list_del_event() on individual events before
they are detached from their group, perf_group_detach() should check each
sibling's attach_state before calling add_event_to_groups() on it.
Fixes: 2e498d0a74e5 ("perf: Add support for event removal on exec") Signed-off-by: Budimir Markovic <markovicbudimir@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/ZBFzvQV9tEqoHEtH@gentoo Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default maximum data buffer size for this interface is UHID_DATA_MAX
(4k). When data buffers are being processed, ensure this value is used
when ensuring the sanity, rather than a value between the user provided
value and HID_MAX_BUFFER_SIZE (16k).
Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Presently, when a report is processed, its proposed size, provided by
the user of the API (as Report Size * Report Count) is compared against
the subsystem default HID_MAX_BUFFER_SIZE (16k). However, some
low-level HID drivers allocate a reduced amount of memory to their
buffers (e.g. UHID only allocates UHID_DATA_MAX (4k) buffers), rending
this check inadequate in some cases.
In these circumstances, if the received report ends up being smaller
than the proposed report size, the remainder of the buffer is zeroed.
That is, the space between sizeof(csize) (size of the current report)
and the rsize (size proposed i.e. Report Size * Report Count), which can
be handled up to HID_MAX_BUFFER_SIZE (16k). Meaning that memset()
shoots straight past the end of the buffer boundary and starts zeroing
out in-use values, often resulting in calamity.
This patch introduces a new variable into 'struct hid_ll_driver' where
individual low-level drivers can over-ride the default maximum value of
HID_MAX_BUFFER_SIZE (16k) with something more sympathetic to the
interface.
Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
[Lee: Backported to v5.15.y] Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_bridge_wait_for_secondary_bus() is called after a Secondary Bus
Reset, but not after a DPC-induced Hot Reset.
As a result, the delays prescribed by PCIe r6.0 sec 6.6.1 are not
observed and devices on the secondary bus may be accessed before
they're ready.
One affected device is Intel's Ponte Vecchio HPC GPU. It comprises a
PCIe switch whose upstream port is not immediately ready after reset.
Because its config space is restored too early, it remains in
D0uninitialized, its subordinate devices remain inaccessible and DPC
recovery fails with messages such as:
i915 0000:8c:00.0: can't change power state from D3cold to D0 (config space inaccessible)
intel_vsec 0000:8e:00.1: can't change power state from D3cold to D0 (config space inaccessible)
pcieport 0000:89:02.0: AER: device recovery failed
Sheng Bi reports that pci_bridge_secondary_bus_reset() may fail to wait
for devices on the secondary bus to become accessible after reset:
Although it does call pci_dev_wait(), it erroneously passes the bridge's
pci_dev rather than that of a child. The bridge of course is always
accessible while its secondary bus is reset, so pci_dev_wait() returns
immediately.
Sheng Bi proposes introducing a new pci_bridge_secondary_bus_wait()
function which is called from pci_bridge_secondary_bus_reset():
However we already have pci_bridge_wait_for_secondary_bus() which does
almost exactly what we need. So far it's only called on resume from
D3cold (which implies a Fundamental Reset per PCIe r6.0 sec 5.8).
Re-using it for Secondary Bus Resets is a leaner and more rational
approach than introducing a new function.
That only requires a few minor tweaks:
- Amend pci_bridge_wait_for_secondary_bus() to await accessibility of
the first device on the secondary bus by calling pci_dev_wait() after
performing the prescribed delays. pci_dev_wait() needs two parameters,
a reset reason and a timeout, which callers must now pass to
pci_bridge_wait_for_secondary_bus(). The timeout is 1 sec for resume
(PCIe r6.0 sec 6.6.1) and 60 sec for reset (commit 821cdad5c46c ("PCI:
Wait up to 60 seconds for device to become ready after FLR")).
Introduce a PCI_RESET_WAIT macro for the 1 sec timeout.
- Amend pci_bridge_wait_for_secondary_bus() to return 0 on success or
-ENOTTY on error for consumption by pci_bridge_secondary_bus_reset().
- Drop an unnecessary 1 sec delay from pci_reset_secondary_bus() which
is now performed by pci_bridge_wait_for_secondary_bus(). A static
delay this long is only necessary for Conventional PCI, so modern
PCIe systems benefit from shorter reset times as a side effect.
Fixes: 6b2f1351af56 ("PCI: Wait for device to become ready after secondary bus reset") Link: https://lore.kernel.org/r/da77c92796b99ec568bd070cbe4725074a117038.1673769517.git.lukas@wunner.de Reported-by: Sheng Bi <windy.bi.enflame@gmail.com> Tested-by: Ravi Kishore Koppuravuri <ravi.kishore.koppuravuri@intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Cc: stable@vger.kernel.org # v4.17+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fedor Pchelkin [Thu, 16 Mar 2023 18:56:16 +0000 (21:56 +0300)]
io_uring: avoid null-ptr-deref in io_arm_poll_handler
No upstream commit exists for this commit.
The issue was introduced with backporting upstream commit c16bda37594f
("io_uring/poll: allow some retries for poll triggering spuriously").
Memory allocation can possibly fail causing invalid pointer be
dereferenced just before comparing it to NULL value.
Move the pointer check in proper place (upstream has the similar location
of the check). In case the request has REQ_F_POLLED flag up, apoll can't
be NULL so no need to check there.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Users reported oopses on list corruptions when using i915 perf with a
number of concurrently running graphics applications. Root cause analysis
pointed at an issue in barrier processing code -- a race among perf open /
close replacing active barriers with perf requests on kernel context and
concurrent barrier preallocate / acquire operations performed during user
context first pin / last unpin.
When adding a request to a composite tracker, we try to reuse an existing
fence tracker, already allocated and registered with that composite. The
tracker we obtain may already track another fence, may be an idle barrier,
or an active barrier.
If the tracker we get occurs a non-idle barrier then we try to delete that
barrier from a list of barrier tasks it belongs to. However, while doing
that we don't respect return value from a function that performs the
barrier deletion. Should the deletion ever fail, we would end up reusing
the tracker still registered as a barrier task. Since the same structure
field is reused with both fence callback lists and barrier tasks list,
list corruptions would likely occur.
Barriers are now deleted from a barrier tasks list by temporarily removing
the list content, traversing that content with skip over the node to be
deleted, then populating the list back with the modified content. Should
that intentionally racy concurrent deletion attempts be not serialized,
one or more of those may fail because of the list being temporary empty.
Related code that ignores the results of barrier deletion was initially
introduced in v5.4 by commit d8af05ff38ae ("drm/i915: Allow sharing the
idle-barrier from other kernel requests"). However, all users of the
barrier deletion routine were apparently serialized at that time, then the
issue didn't exhibit itself. Results of git bisect with help of a newly
developed igt@gem_barrier_race@remote-request IGT test indicate that list
corruptions might start to appear after commit 311770173fac ("drm/i915/gt:
Schedule request retirement when timeline idles"), introduced in v5.5.
Respect results of barrier deletion attempts -- mark the barrier as idle
only if successfully deleted from the list. Then, before proceeding with
setting our fence as the one currently tracked, make sure that the tracker
we've got is not a non-idle barrier. If that check fails then don't use
that tracker but go back and try to acquire a new, usable one.
v3: use unlikely() to document what outcome we expect (Andi),
- fix bad grammar in commit description.
v2: no code changes,
- blame commit 311770173fac ("drm/i915/gt: Schedule request retirement
when timeline idles"), v5.5, not commit d8af05ff38ae ("drm/i915: Allow
sharing the idle-barrier from other kernel requests"), v5.4,
- reword commit description.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6333 Fixes: 311770173fac ("drm/i915/gt: Schedule request retirement when timeline idles") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: stable@vger.kernel.org # v5.5 Cc: Andi Shyti <andi.shyti@linux.intel.com> Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com> Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com> Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230302120820.48740-1-janusz.krzysztofik@linux.intel.com
(cherry picked from commit 506006055769b10d1b2b4e22f636f3b45e0e9fc7) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Direction from hardware is that stolen memory should never be used for
ring buffer allocations on platforms with LLC. There are too many
caching pitfalls due to the way stolen memory accesses are routed. So
it is safest to just not use it.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Fixes: c58b735fc762 ("drm/i915: Allocate rings from stolen") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: intel-gfx@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v4.9+ Tested-by: Jouni Högander <jouni.hogander@intel.com> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230216011101.1909009-2-John.C.Harrison@Intel.com
(cherry picked from commit f54c1f6c697c4297f7ed94283c184acc338a5cf8) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a temporary storage, staged_config[] in rdt_domain should be cleared
before and after it is used. The stale value in staged_config[] could
cause an MSR access error.
Here is a reproducer on a system with 16 usable CLOSIDs for a 15-way L3
Cache (MBA should be disabled if the number of CLOSIDs for MB is less than
16.) :
mount -t resctrl resctrl -o cdp /sys/fs/resctrl
mkdir /sys/fs/resctrl/p{1..7}
umount /sys/fs/resctrl/
mount -t resctrl resctrl /sys/fs/resctrl
mkdir /sys/fs/resctrl/p{1..8}
An error occurs when creating resource group named p8:
unchecked MSR access error: WRMSR to 0xca0 (tried to write 0x00000000000007ff) at rIP: 0xffffffff82249142 (cat_wrmsr+0x32/0x60)
Call Trace:
<IRQ>
__flush_smp_call_function_queue+0x11d/0x170
__sysvec_call_function+0x24/0xd0
sysvec_call_function+0x89/0xc0
</IRQ>
<TASK>
asm_sysvec_call_function+0x16/0x20
When creating a new resource control group, hardware will be configured
by the following process:
rdtgroup_mkdir()
rdtgroup_mkdir_ctrl_mon()
rdtgroup_init_alloc()
resctrl_arch_update_domains()
resctrl_arch_update_domains() iterates and updates all resctrl_conf_type
whose have_new_ctrl is true. Since staged_config[] holds the same values as
when CDP was enabled, it will continue to update the CDP_CODE and CDP_DATA
configurations. When group p8 is created, get_config_index() called in
resctrl_arch_update_domains() will return 16 and 17 as the CLOSIDs for
CDP_CODE and CDP_DATA, which will be translated to an invalid register -
0xca0 in this scenario.
Fix it by clearing staged_config[] before and after it is used.
[reinette: re-order commit tags]
Fixes: 75408e43509e ("x86/resctrl: Allow different CODE/DATA configurations to be staged") Suggested-by: Xin Hao <xhao@linux.alibaba.com> Signed-off-by: Shawn Wang <shawnwang@linux.alibaba.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Cc:stable@vger.kernel.org Link: https://lore.kernel.org/all/2fad13f49fbe89687fc40e9a5a61f23a28d1507a.1673988935.git.reinette.chatre%40intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cmdline_find_option() may fail before doing any initialization of
the buffer array. This may lead to unpredictable results when the same
buffer is used later in calls to strncmp() function. Fix the issue by
returning early if cmdline_find_option() returns an error.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: aca20d546214 ("x86/mm: Add support to make use of Secure Memory Encryption") Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Cc: <stable@kernel.org> Link: https://lore.kernel.org/r/20230306160656.14844-1-n.zhandarovich@fintech.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent change introduced a flag to queue up errors found during
boot-time polling. These errors will be processed during late init once
the MCE subsystem is fully set up.
A number of sysfs updates call mce_restart() which goes through a subset
of the CPU init flow. This includes polling MCA banks and logging any
errors found. Since the same function is used as boot-time polling,
errors will be queued. However, the system is now past late init, so the
errors will remain queued until another error is found and the workqueue
is triggered.
Call mce_schedule_work() at the end of mce_restart() so that queued
errors are processed.
Fixes: 3bff147b187d ("x86/mce: Defer processing of early errors") Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Reviewed-by: Tony Luck <tony.luck@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230301221420.2203184-1-yazen.ghannam@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case that psci_pd_init_topology() fails for some reason,
psci_pd_remove() will be responsible for deleting provider and removing
genpd from psci_pd_providers list. There will be a failure when removing
the cluster PD, because the cpu (child) PDs haven't been removed.
Do not wipe the contents of the per-cpu kthread data when starting the
tracer, as this will completely forget about already running instances
and can later start new additional per-cpu threads.
Find a valid modeline depending on the machine graphic card
configuration and add the fb_check_var() function to validate
Xorg provided graphics settings.
Lower the power-on failed message severity from warn to info when the
controller does not power-up. It's normal to have this situation when
the SD card slot is empty, therefore we should not warn the user about
it.
Currently, we'd lose the userfaultfd-wp marker when PTE-mapping a huge
zeropage, resulting in the next write faults in the PMD range not
triggering uffd-wp events.
Various actions (partial MADV_DONTNEED, partial mremap, partial munmap,
partial mprotect) could trigger this. However, most importantly,
un-protecting a single sub-page from the userfaultfd-wp handler when
processing a uffd-wp event will PTE-map the shared huge zeropage and lose
the uffd-wp bit for the remainder of the PMD.
Let's properly propagate the uffd-wp bit to the PMDs.
RDMA is not supported in ice on a PF that has been added to a bonded
interface. To enforce this, when an interface enters a bond, we unplug
the auxiliary device that supports RDMA functionality. This unplug
currently happens in the context of handling the netdev bonding event.
This event is sent to the ice driver under RTNL context. This is causing
a deadlock where the RDMA driver is waiting for the RTNL lock to complete
the removal.
Defer the unplugging/re-plugging of the auxiliary device to the service
task so that it is not performed under the RTNL lock context.
Cc: stable@vger.kernel.org # 6.1.x Reported-by: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com> Link: https://lore.kernel.org/netdev/CAK8fFZ6A_Gphw_3-QMGKEFQk=sfCw1Qmq0TVZK3rtAi7vb621A@mail.gmail.com/ Fixes: 5cb1ebdbc434 ("ice: Fix race condition during interface enslave") Fixes: 4eace75e0853 ("RDMA/irdma: Report the correct link speed") Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230310194833.3074601-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KASAN: use-after-free in lookup_rec
Read of size 8 at addr ffff000199270ff0 by task modprobe
CPU: 2 Comm: modprobe
Call trace:
kasan_report
__asan_load8
lookup_rec
ftrace_location
arch_check_ftrace_location
check_kprobe_address_safe
register_kprobe
When checking pg->records[pg->index - 1].ip in lookup_rec(), it can get a
pg which is newly added to ftrace_pages_start in ftrace_process_locs().
Before the first pg->index++, index is 0 and accessing pg->records[-1].ip
will cause this problem.
Don't check the ip when pg->index is 0.
Link: https://lore.kernel.org/linux-trace-kernel/20230309080230.36064-1-chenzhongjin@huawei.com Cc: stable@vger.kernel.org Fixes: 9644302e3315 ("ftrace: Speed up search by skipping pages by address") Suggested-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph reports a lockdep splat in the mptcp_subflow_create_socket()
error path, when such function is invoked by
mptcp_pm_nl_create_listen_socket().
Such code path acquires two separates, nested socket lock, with the
internal lock operation lacking the "nested" annotation. Adding that
in sock_release() for mptcp's sake only could be confusing.
Instead just add a new lockclass to the in-kernel msk socket,
re-initializing the lockdep infra after the socket creation.
Fixes: ad2171009d96 ("mptcp: fix locking for in-kernel listener creation") Cc: stable@vger.kernel.org Reported-by: Christoph Paasch <cpaasch@apple.com> Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/354 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Tested-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add __ro_after_init labels for the variables tcp_prot_override and
tcpv6_prot_override, just like other variables adjacent to them, to
indicate that they are initialised from the init hooks and no writes
occur afterwards.
Christoph reported a possible deadlock while the TCP stack
destroys an unaccepted subflow due to an incoming reset: the
MPTCP socket error path tries to acquire the msk-level socket
lock while TCP still owns the listener socket accept queue
spinlock, and the reverse dependency already exists in the
TCP stack.
Note that the above is actually a lockdep false positive, as
the chain involves two separate sockets. A different per-socket
lockdep key will address the issue, but such a change will be
quite invasive.
Instead, we can simply stop earlier the socket error handling
for orphaned or unaccepted subflows, breaking the critical
lockdep chain. Error handling in such a scenario is a no-op.
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com> Fixes: 15cc10453398 ("mptcp: deliver ssk errors to msk") Cc: stable@vger.kernel.org Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/355 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always setup overdrive tables after resume. Preserve only some
user-defined settings in user_overdrive_table if they're set.
Copy restored user_overdrive_table into od_table to get correct
values.
On cold boot, BTC was triggered and GfxVfCurve was calibrated. We
got VfCurve settings (a). On resuming back, BTC will be triggered
again and GfxVfCurve will be recalibrated. VfCurve settings (b)
got may be different from those of cold boot. So if we reuse
those VfCurve settings (a) got on cold boot on suspend, we can
run into discrepencies.
drm_gem_shmem_mmap() doesn't own reference in error code path, resulting
in the dma-buf shmem GEM object getting prematurely freed leading to a
later use-after-free.
After use_asid_allocator is enabled, the userspace application will
crash by stale TLB entries. Because only using cpumask_clear_cpu without
local_flush_tlb_all couldn't guarantee CPU's TLB entries were fresh.
Then set_mm_asid would cause the user space application to get a stale
value by stale TLB entry, but set_mm_noasid is okay.
Here is the symptom of the bug:
unhandled signal 11 code 0x1 (coredump)
0x0000003fd6d22524 <+4>: auipc s0,0x70
0x0000003fd6d22528 <+8>: ld s0,-148(s0) # 0x3fd6d92490
=> 0x0000003fd6d2252c <+12>: ld a5,0(s0)
(gdb) i r s0
s0 0x8082ed1cc3198b21 0x8082ed1cc3198b21
(gdb) x /2x 0x3fd6d92490
0x3fd6d92490: 0xd80ac8a8 0x0000003f
The core dump file shows that register s0 is wrong, but the value in
memory is correct. Because 'ld s0, -148(s0)' used a stale mapping entry
in TLB and got a wrong result from an incorrect physical address.
When the task ran on CPU0, which loaded/speculative-loaded the value of
address(0x3fd6d92490), then the first version of the mapping entry was
PTWed into CPU0's TLB.
When the task switched from CPU0 to CPU1 (No local_tlb_flush_all here by
asid), it happened to write a value on the address (0x3fd6d92490). It
caused do_page_fault -> wp_page_copy -> ptep_clear_flush ->
ptep_get_and_clear & flush_tlb_page.
The flush_tlb_page used mm_cpumask(mm) to determine which CPUs need TLB
flush, but CPU0 had cleared the CPU0's mm_cpumask in the previous
switch_mm. So we only flushed the CPU1 TLB and set the second version
mapping of the PTE. When the task switched from CPU1 to CPU0 again, CPU0
still used a stale TLB mapping entry which contained a wrong target
physical address. It raised a bug when the task happened to read that
value.
CPU0 CPU1
- switch 'task' in
- read addr (Fill stale mapping
entry into TLB)
- switch 'task' out (no tlb_flush)
- switch 'task' in (no tlb_flush)
- write addr cause pagefault
do_page_fault() (change to
new addr mapping)
wp_page_copy()
ptep_clear_flush()
ptep_get_and_clear()
& flush_tlb_page()
write new value into addr
- switch 'task' out (no tlb_flush)
- switch 'task' in (no tlb_flush)
- read addr again (Use stale
mapping entry in TLB)
get wrong value from old phyical
addr, BUG!
The solution is to keep all CPUs' footmarks of cpumask(mm) in switch_mm,
which could guarantee to invalidate all stale TLB entries during TLB
flush.
Samsung Galaxy Book2 Pro (13" 2022 NP930XED-KA1DE) with codec SSID
144d:c868 requires the same workaround for enabling the speaker amp
like other Samsung models with ALC298 code.
The effective values of the guest CR0 and CR4 registers may differ from
those included in the VMCS12. In particular, disabling EPT forces
CR4.PAE=1 and disabling unrestricted guest mode forces CR0.PG=CR0.PE=1.
Therefore, checks on these bits cannot be delegated to the processor
and must be performed by KVM.
If the tracepoint is enabled, it could trigger RCU issues if called in
the wrong place. And this warning was only triggered if lockdep was
enabled. If the tracepoint was never enabled with lockdep, the bug would
not be caught. To handle this, the above sequence was done when lockdep
was enabled regardless if the tracepoint was enabled or not (although the
always enabled code really didn't do anything, it would still trigger a
warning).
But a lot has changed since that lockdep code was added. One is, that
sequence no longer triggers any warning. Another is, the tracepoint when
enabled doesn't even do that sequence anymore.
The main check we care about today is whether RCU is "watching" or not.
So if lockdep is enabled, always check if rcu_is_watching() which will
trigger a warning if it is not (tracepoints require RCU to be watching).
Note, that old sequence did add a bit of overhead when lockdep was enabled,
and with the latest kernel updates, would cause the system to slow down
enough to trigger kernel "stalled" warnings.
The function hist_field_name() cannot handle being passed a NULL field
parameter. It should never be NULL, but due to a previous bug, NULL was
passed to the function and the kernel crashed due to a NULL dereference.
Mark Rutland reported this to me on IRC.
The bug was fixed, but to prevent future bugs from crashing the kernel,
check the field and add a WARN_ON() if it is NULL.
Link: https://lkml.kernel.org/r/20230302020810.762384440@goodmis.org Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Reported-by: Mark Rutland <mark.rutland@arm.com> Fixes: c6afad49d127f ("tracing: Add hist trigger 'sym' and 'sym-offset' modifiers") Tested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the commit 36e2c7421f02 ("fs: don't allow splice read/write
without explicit ops") is applied to the kernel, splice() and
sendfile() calls on the trace file (/sys/kernel/debug/tracing
/trace) return EINVAL.
This patch restores these system calls by initializing splice_read
in file_operations of the trace file. This patch only enables such
functionalities for the read case.
Link: https://lore.kernel.org/linux-trace-kernel/20230314013707.28814-1-sfoon.kim@samsung.com Cc: stable@vger.kernel.org Fixes: 36e2c7421f02 ("fs: don't allow splice read/write without explicit ops") Signed-off-by: Sung-hun Kim <sfoon.kim@samsung.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code which handles the ipl report is searching for a free location
in memory where it could copy the component and certificate entries to.
It checks for intersection between the sections required for the kernel
and the component/certificate data area, but fails to check whether
the data structures linking these data areas together intersect.
This might cause the iplreport copy code to overwrite the iplreport
itself. Fix this by adding two addtional intersection checks.
Cc: <stable@vger.kernel.org> Fixes: 9641b8cc733f ("s390/ipl: read IPL report at early boot") Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Reviewed-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 handle_irq callback is not just called from the interrupt
handler but also from a timer callback when polling (e.g. for ports
without an interrupt line). Consequently the callback must explicitly
disable interrupts to avoid a potential deadlock with another interrupt
in polled mode.
Fix up the two paths in the freescale callback that failed to re-enable
interrupts when polling.
As per HW manual for EMEV2 "R19UH0040EJ0400 Rev.4.00", the UART
IP found on EMMA mobile SoC is Register-compatible with the
general-purpose 16750 UART chip. Fix UART port type as 16750 and
enable 64-bytes fifo support.
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to skip
waiting for transmission complete when UARTCTRL_SBK is asserted,
otherwise the kernel may stuck here.
And actually set_termios() adds transmission completion waiting to avoid
data loss or data breakage when changing the baud rate, but we don't
need to worry about this when queuing break characters.
[WHY]
When PTEBufferSizeInRequests is zero, UBSAN reports the following
warning because dml_log2 returns an unexpected negative value:
shift exponent 4294966273 is too large for 32-bit type 'int'
[HOW]
In the case PTEBufferSizeInRequests is zero, skip the dml_log2() and
assign the result directly.
Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
GCC warns about the pattern sizeof(void*)/sizeof(void), as it looks like
the abuse of a pattern to calculate the array size. This pattern appears
in the unevaluated part of the ternary operator in _INTC_ARRAY if the
parameter is NULL.
The replacement uses an alternate approach to return 0 in case of NULL
which does not generate the pattern sizeof(void*)/sizeof(void), but still
emits the warning if _INTC_ARRAY is called with a nonarray parameter.
This patch is required for successful compilation with -Werror enabled.
The idea to use _Generic for type distinction is taken from Comment #7
in https://gcc.gnu.org/bugzilla/show_bug.cgi?id=108483 by Jakub Jelinek
We are supposed to set fid->mode to reflect the flags
that were used to open the file. We were actually setting
it to the creation mode which is the default perms of the
file not the flags the file was opened with.
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org> Reviewed-by: Dominique Martinet <asmadeus@codewreck.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the kfd_wait_on_events() function, the kfd_event_waiter structure is
allocated by alloc_event_waiters(), but the event field of the waiter
structure is not initialized; When copy_from_user() fails in the
kfd_wait_on_events() function, it will enter exception handling to
release the previously allocated memory of the waiter structure;
Due to the event field of the waiters structure being accessed
in the free_waiters() function, this results in illegal memory access
and system crash, here is the crash log:
The problem is that the inode contains an xattr entry with ea_inum of 15
when cleaning up an orphan inode <15>. When evict inode <15>, the reference
counting of the corresponding EA inode is decreased. When EA inode <15> is
found by find_inode_fast() in __ext4_iget(), it is found that the EA inode
holds the I_FREEING flag and waits for the EA inode to complete deletion.
As a result, when inode <15> is being deleted, we wait for inode <15> to
complete the deletion, resulting in an infinite loop and triggering Hung
Task. To solve this problem, we only need to check whether the ino of EA
inode and parent is the same before getting EA inode.
When mounting a crafted ext4 image, s_journal_inum may change after journal
replay, which is obviously unreasonable because we have successfully loaded
and replayed the journal through the old s_journal_inum. And the new
s_journal_inum bypasses some of the checks in ext4_get_journal(), which
may trigger a null pointer dereference problem. So if s_journal_inum
changes after the journal replay, we ignore the change, and rewrite the
current journal_inum to the superblock.
In ext4_fill_super(), EXT4_ORPHAN_FS flag is cleared after
ext4_orphan_cleanup() is executed. Therefore, when __ext4_iget() is
called to get an inode whose i_nlink is 0 when the flag exists, no error
is returned. If the inode is a special inode, a null pointer dereference
may occur. If the value of i_nlink is 0 for any inodes (except boot loader
inodes) got by using the EXT4_IGET_SPECIAL flag, the current file system
is corrupted. Therefore, make the ext4_iget() function return an error if
it gets such an abnormal special inode.
1. Write data to a file, say all 1s from offset 0 to 16.
2. Truncate the file to a smaller size, say 8 bytes.
3. Write new bytes (say 2s) from an offset past the original size of the
file, say at offset 20, for 4 bytes. This is supposed to create a "hole"
in the file, meaning that the bytes from offset 8 (where it was truncated
above) up to the new write at offset 20, should all be 0s (zeros).
4. Flush all caches using "echo 3 > /proc/sys/vm/drop_caches" (or unmount
and remount) the f/s.
5. Check the content of the file. It is wrong. The 1s that used to be
between bytes 9 and 16, before the truncation, have REAPPEARED (they should
be 0s).
We wrote a script and helper C program to reproduce the bug
(reproduce_jffs2_write_begin_issue.sh, write_file.c, and Makefile). We can
make them available to anyone.
The above example is shown when writing a small file within the same first
page. But the bug happens for larger files, as long as steps 1, 2, and 3
above all happen within the same page.
The problem was traced to the jffs2_write_begin code, where it goes into an
'if' statement intended to handle writes past the current EOF (i.e., writes
that may create a hole). The code computes a 'pageofs' that is the floor
of the write position (pos), aligned to the page size boundary. In other
words, 'pageofs' will never be larger than 'pos'. The code then sets the
internal jffs2_raw_inode->isize to the size of max(current inode size,
pageofs) but that is wrong: the new file size should be the 'pos', which is
larger than both the current inode size and pageofs.
Similarly, the code incorrectly sets the internal jffs2_raw_inode->dsize to
the difference between the pageofs minus current inode size; instead it
should be the current pos minus the current inode size. Finally,
inode->i_size was also set incorrectly.
The patch below fixes this bug. The bug was discovered using a new tool
for finding f/s bugs using model checking, called MCFS (Model Checking File
Systems).
Signed-off-by: Yifei Liu <yifeliu@cs.stonybrook.edu> Signed-off-by: Erez Zadok <ezk@cs.stonybrook.edu> Signed-off-by: Manish Adkar <madkar@cs.stonybrook.edu> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit fixes a race between completion of stop command and start of a
new command.
Previously the command ready interrupt was enabled before stop command
was written to the command register. This caused the command ready
interrupt to fire immediately since the CMDRDY flag is asserted constantly
while there is no command in progress.
Consequently the command state machine will immediately advance to the
next state when the tasklet function is executed again, no matter
actual completion state of the stop command.
Thus a new command can then be dispatched immediately, interrupting and
corrupting the stop command on the CMD line.
Fix that by dropping the command ready interrupt enable before calling
atmci_send_stop_cmd. atmci_send_stop_cmd does already enable the
command ready interrupt, no further writes to ATMCI_IER are necessary.
The __find_restype() function loops over the m5mols_default_ffmt[]
array, and the termination condition ends up being wrong: instead of
stopping when the iterator becomes the size of the array it traverses,
it stops after it has already overshot the array.
Now, in practice this doesn't likely matter, because the code will
always find the entry it looks for, and will thus return early and never
hit that last extra iteration.
But it turns out that clang will unroll the loop fully, because it has
only two iterations (well, three due to the off-by-one bug), and then
clang will end up just giving up in the middle of the loop unrolling
when it notices that the code walks past the end of the array.
And that made 'objtool' very unhappy indeed, because the generated code
just falls off the edge of the universe, and ends up falling through to
the next function, causing this warning:
drivers/media/i2c/m5mols/m5mols.o: warning: objtool: m5mols_set_fmt() falls through to next function m5mols_get_frame_desc()
Fix the loop ending condition.
Reported-by: Jens Axboe <axboe@kernel.dk> Analyzed-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> Analyzed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/linux-block/CAHk-=wgTSdKYbmB1JYM5vmHMcD9J9UZr0mn7BOYM_LudrP+Xvw@mail.gmail.com/ Fixes: bc125106f8af ("[media] Add support for M-5MOLS 8 Mega Pixel camera ISP") Cc: HeungJun, Kim <riverful.kim@samsung.com> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ltc2992 drivers uses a mutex and I2C bus access in its GPIO chip `set`
and `get` implementation. This means these functions can sleep and the GPIO
chip should set the `can_sleep` property to true.
This will ensure that a warning is printed when trying to set or get the
GPIO value from a context that potentially can't sleep.
The adm1266 driver uses I2C bus access in its GPIO chip `set` and `get`
implementation. This means these functions can sleep and the GPIO chip
should set the `can_sleep` property to true.
This will ensure that a warning is printed when trying to set or get the
GPIO value from a context that potentially can't sleep.
Prior to commit 5ee546594025 ("kconfig: change sym_change_count to a
boolean flag"), the conf_updated flag was set to the new value *before*
calling the callback. xconfig's save action depends on this behaviour,
because xconfig calls conf_get_changed() directly from the callback and
now sees the old value, thus never enabling the save button or the
shortcut.
Restore the previous behaviour.
Fixes: 5ee546594025 ("kconfig: change sym_change_count to a boolean flag") Signed-off-by: Jurica Vukadin <jura@vukad.in> Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
This also fixes !CONFIG_OF error:
drivers/hwmon/tmp513.c:610:34: error: ‘tmp51x_of_match’ defined but not used [-Werror=unused-const-variable=]
When probing the ucd90320 access to some of the registers randomly fails.
Sometimes it NACKs a transfer, sometimes it returns just random data and
the PEC check fails.
Experimentation shows that this seems to be triggered by a register access
directly back to back with a previous register write. Experimentation also
shows that inserting a small delay after register writes makes the issue go
away.
Use a similar solution to what the max15301 driver does to solve the same
problem. Create a custom set of bus read and write functions that make sure
that the delay is added.
Fixes: a470f11c5ba2 ("hwmon: (pmbus/ucd9000) Add support for UCD90320 Power Sequencer") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Link: https://lore.kernel.org/r/20230312160312.2227405-1-lars@metafoo.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The wrong bits are masked in the hysteresis register; indices 0 and 2
should zero bits [7:4] and preserve bits [3:0], and index 1 should zero
bits [3:0] and preserve bits [7:4].
Fixes: 1c301fc5394f ("hwmon: Add a driver for the ADT7475 hardware monitoring chip") Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz> Link: https://lore.kernel.org/r/20230222005228.158661-3-tony.obrien@alliedtelesis.co.nz Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Throughout the ADT7475 driver, attributes relating to the temperature
sensors are displayed in the order Remote 1, Local, Remote 2. Make
temp_st_show() conform to this expectation so that values set by
temp_st_store() can be displayed using the correct attribute.
syzbot reported a warning[1] where the bond device itself is a slave and
we try to enslave a non-ethernet device as the first slave which fails
but then in the error path when ether_setup() restores the bond device
it also clears all flags. In my previous fix[2] I restored the
IFF_MASTER flag, but I didn't consider the case that the bond device
itself might also be a slave with IFF_SLAVE set, so we need to restore
that flag as well. Use the bond_ether_setup helper which does the right
thing and restores the bond's flags properly.
Steps to reproduce using a nlmon dev:
$ ip l add nlmon0 type nlmon
$ ip l add bond1 type bond
$ ip l add bond2 type bond
$ ip l set bond1 master bond2
$ ip l set dev nlmon0 master bond1
$ ip -d l sh dev bond1
22: bond1: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noqueue master bond2 state DOWN mode DEFAULT group default qlen 1000
(now bond1's IFF_SLAVE flag is gone and we'll hit a warning[3] if we
try to delete it)
Fixes: 7d5cd2ce5292 ("bonding: correctly handle bonding type change on enslave failure") Reported-by: syzbot+9dfc3f3348729cc82277@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?id=391c7b1f6522182899efba27d891f1743e8eb3ef Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Acked-by: Jonathan Toppins <jtoppins@redhat.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add bond_ether_setup helper which is used to fix ether_setup() calls in the
bonding driver. It takes care of both IFF_MASTER and IFF_SLAVE flags, the
former is always restored and the latter only if it was set.
If the bond enslaves non-ARPHRD_ETHER device (changes its type), then
releases it and enslaves ARPHRD_ETHER device (changes back) then we
use ether_setup() to restore the bond device type but it also resets its
flags and removes IFF_MASTER and IFF_SLAVE[1]. Use the bond_ether_setup
helper to restore both after such transition.
[1] reproduce (nlmon is non-ARPHRD_ETHER):
$ ip l add nlmon0 type nlmon
$ ip l add bond2 type bond mode active-backup
$ ip l set nlmon0 master bond2
$ ip l set nlmon0 nomaster
$ ip l add bond1 type bond
(we use bond1 as ARPHRD_ETHER device to restore bond2's mode)
$ ip l set bond1 master bond2
$ ip l sh dev bond2
37: bond2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether be:d7:c5:40:5b:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 1500
(notice bond2's IFF_MASTER is missing)
Fixes: e36b9d16c6a6 ("bonding: clean muticast addresses when device changes type") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The `devlink -j port show` command output may not contain the "flavour"
key, an example from Ubuntu 22.10 s390x LPAR(5.19.0-37-generic), with
mlx4 driver and iproute2-5.15.0:
{"port":{"pci/0001:00:00.0/1":{"type":"eth","netdev":"ens301"},
"pci/0001:00:00.0/2":{"type":"eth","netdev":"ens301d1"},
"pci/0002:00:00.0/1":{"type":"eth","netdev":"ens317"},
"pci/0002:00:00.0/2":{"type":"eth","netdev":"ens317d1"}}}
This will cause a KeyError exception.
Create a validate_devlink_output() to check for this "flavour" from
devlink command output to avoid this KeyError exception. Also let
it handle the check for `devlink -j dev show` output in main().
Apart from this, if the test was not started because the max lanes of
the designated device is 0. The script will still return 0 and thus
causing a false-negative test result.
Use a found_max_lanes flag to determine if these tests were skipped
due to this reason and return KSFT_SKIP to make it more clear.
iucv_irq_data needs to be 4 bytes larger.
These bytes are not used by the iucv module, but written by
the z/VM hypervisor in case a CPU is deconfigured.
Reported as:
BUG dma-kmalloc-64 (Not tainted): kmalloc Redzone overwritten
-----------------------------------------------------------------------------
0x0000000000400564-0x0000000000400567 @offset=1380. First byte 0x80 instead of 0xcc
Allocated in iucv_cpu_prepare+0x44/0xd0 age=167839 cpu=2 pid=1
__kmem_cache_alloc_node+0x166/0x450
kmalloc_node_trace+0x3a/0x70
iucv_cpu_prepare+0x44/0xd0
cpuhp_invoke_callback+0x156/0x2f0
cpuhp_issue_call+0xf0/0x298
__cpuhp_setup_state_cpuslocked+0x136/0x338
__cpuhp_setup_state+0xf4/0x288
iucv_init+0xf4/0x280
do_one_initcall+0x78/0x390
do_initcalls+0x11a/0x140
kernel_init_freeable+0x25e/0x2a0
kernel_init+0x2e/0x170
__ret_from_fork+0x3c/0x58
ret_from_fork+0xa/0x40
Freed in iucv_init+0x92/0x280 age=167839 cpu=2 pid=1
__kmem_cache_free+0x308/0x358
iucv_init+0x92/0x280
do_one_initcall+0x78/0x390
do_initcalls+0x11a/0x140
kernel_init_freeable+0x25e/0x2a0
kernel_init+0x2e/0x170
__ret_from_fork+0x3c/0x58
ret_from_fork+0xa/0x40
Slab 0x0000037200010000 objects=32 used=30 fp=0x0000000000400640 flags=0x1ffff00000010200(slab|head|node=0|zone=0|
Object 0x0000000000400540 @offset=1344 fp=0x0000000000000000
Redzone 0000000000400500: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 0000000000400510: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 0000000000400520: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 0000000000400530: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Object 0000000000400540: 00 01 00 03 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object 0000000000400550: f3 86 81 f2 f4 82 f8 82 f0 f0 f0 f0 f0 f0 f0 f2 ................
Object 0000000000400560: 00 00 00 00 80 00 00 00 cc cc cc cc cc cc cc cc ................
Object 0000000000400570: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 0000000000400580: cc cc cc cc cc cc cc cc ........
Padding 00000000004005d4: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
Padding 00000000004005e4: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
Padding 00000000004005f4: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZ
CPU: 6 PID: 121030 Comm: 116-pai-crypto. Not tainted 6.3.0-20230221.rc0.git4.99b8246b2d71.300.fc37.s390x+debug #1
Hardware name: IBM 3931 A01 704 (z/VM 7.3.0)
Call Trace:
[<000000032aa034ec>] dump_stack_lvl+0xac/0x100
[<0000000329f5a6cc>] check_bytes_and_report+0x104/0x140
[<0000000329f5aa78>] check_object+0x370/0x3c0
[<0000000329f5ede6>] free_debug_processing+0x15e/0x348
[<0000000329f5f06a>] free_to_partial_list+0x9a/0x2f0
[<0000000329f5f4a4>] __slab_free+0x1e4/0x3a8
[<0000000329f61768>] __kmem_cache_free+0x308/0x358
[<000000032a91465c>] iucv_cpu_dead+0x6c/0x88
[<0000000329c2fc66>] cpuhp_invoke_callback+0x156/0x2f0
[<000000032aa062da>] _cpu_down.constprop.0+0x22a/0x5e0
[<0000000329c3243e>] cpu_device_down+0x4e/0x78
[<000000032a61dee0>] device_offline+0xc8/0x118
[<000000032a61e048>] online_store+0x60/0xe0
[<000000032a08b6b0>] kernfs_fop_write_iter+0x150/0x1e8
[<0000000329fab65c>] vfs_write+0x174/0x360
[<0000000329fab9fc>] ksys_write+0x74/0x100
[<000000032aa03a5a>] __do_syscall+0x1da/0x208
[<000000032aa177b2>] system_call+0x82/0xb0
INFO: lockdep is turned off.
FIX dma-kmalloc-64: Restoring kmalloc Redzone 0x0000000000400564-0x0000000000400567=0xcc
FIX dma-kmalloc-64: Object at 0x0000000000400540 not freed
Fixes: 2356f4cb1911 ("[S390]: Rewrite of the IUCV base code, part 2") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Link: https://lore.kernel.org/r/20230315131435.4113889-1-wintera@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Packet length check needs to be located after size and align_count
calculation to prevent kernel panic in skb_pull() in case
rx_cmd_a & RX_CMD_A_RED evaluates to true.
Commit f96a3d74554d ("ipv4: Fix incorrect route flushing when source
address is deleted") started to take the table ID field in the FIB info
structure into account when determining if two structures are identical
or not. This field is initialized using the 'fc_table' field in the
route configuration structure, which is not set when adding a route via
IOCTL.
The above can result in user space being able to install two identical
routes that only differ in the table ID field of their associated FIB
info.
Fix by initializing the table ID field in the route configuration
structure in the IOCTL path.
Before the fix:
# ip route add default via 192.0.2.2
# route add default gw 192.0.2.2
# ip -4 r show default
# default via 192.0.2.2 dev dummy10
# default via 192.0.2.2 dev dummy10
After the fix:
# ip route add default via 192.0.2.2
# route add default gw 192.0.2.2
SIOCADDRT: File exists
# ip -4 r show default
default via 192.0.2.2 dev dummy10
Audited the code paths to ensure there are no other paths that do not
properly initialize the route configuration structure when installing a
route.
Fixes: 5a56a0b3a45d ("net: Don't delete routes in different VRFs") Fixes: f96a3d74554d ("ipv4: Fix incorrect route flushing when source address is deleted") Reported-by: gaoxingwang <gaoxingwang1@huawei.com> Link: https://lore.kernel.org/netdev/20230314144159.2354729-1-gaoxingwang1@huawei.com/ Tested-by: gaoxingwang <gaoxingwang1@huawei.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20230315124009.4015212-1-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
SH_ETH doesn't need mdiobus suspend/resume, that's why it sets
'mac_managed_pm'. However, setting it needs to be moved from init to
probe, so mdiobus PM functions will really never be called (e.g. when
the interface is not up yet during suspend/resume).
Fixes: 6a1dbfefdae4 ("net: sh_eth: Fix PHY state warning splat during system resume") Suggested-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
