BFD: Better handling of BFD options in BGP configs
Merge multiple BFD option blocks in BGP configs instead of using the last
one. That is necessary for proper handling of templates when BFD options
are used both in a BGP template and in a BGP protocol derived from that
template.
BFD session options are configured per interface in BFD protocol. This
patch allows to specify them also per-request in protocols requesting
sessions (currently limited to BGP).
Add 'ignore max length' option to RPKI protocol, which ignores received
max length in ROA records and instead uses max value (32 or 128). This
may be useful for implementing loose RPKI check for blackholes.
Sometimes multicast OSPF packet is received when neighbor adjacency is
not established. Such packet should be ignored earlier in packet
processing as otherwise it causes strange error messages when OSPFv3
authentication is enabled.
Put new non-best routes to the end of list instead of the second
position. Put updated routes to their old position. Position is changed
just by best route selection.
Show info from multiple protocols when protocol is not specified
Most commands like 'show ospf neighbors' fail when protocol is not
specified and there are multiple instances of given protocol type.
This is annoying in BIRD 2, as many protocols have IPv4 and IPv6
instances. The patch changes that by showing output from all protocol
instances of appropriate type.
Note that the patch also removes terminating cli_msg() call from these
commands and moves it to the common iterating code.
Kazuki Yamaguchi [Sun, 28 Jun 2020 13:37:01 +0000 (15:37 +0200)]
Filter: Improve handling of sets in BGP path masks
Compare the content of PM_ASN_SET in path masks. A reconfiguration
was not properly triggering a reload of affected protocols when the
members of a set in a path mask change.
Also, update the printing code to so that it can display sets in a path
mask.
Kazuki Yamaguchi [Sun, 28 Jun 2020 13:33:26 +0000 (15:33 +0200)]
Filter: Fix comparison of BGP path mask
Add a missing return statement. Path masks with the same length were all
considered the same. Comparing two with different length would cause
out-of-bounds memory access.
Add support for RTA_MULTIPATH attribute parsing for AF_MPLS routes.
BIRD is capable of installing a multipath route into kernel on Linux,
but it would not be seen because parsing fails. This made BIRD attempt
to install the same route repeatedly.
RPKI: Fix unnecessary reconnection on reconfiguration
Compare the new timing parameters with the old configuration, not with
the temporary state of the current connection.
The timing values in struct rpki_cache is updated by a version 1 End Of
Data PDU, unless this behavior is suppressed by the configuration
explicitly by the "keep" keyword. Consequently, every reconfiguration
of BIRD triggers a reconnection even if it is not necessary.
Log: Do not open logfiles when parse-and-exit option is active
This is a quick workaround for an issue where configured logfiles are
opened/created during parsing of a config file even when parse-and-exit
option is active. We should later refactor the logging code to avoid
opening log during parsing altogether.
Babel: Set onlink flag for IPv4 routes with unreachable next hop
If the next hop of a route is not a reachable address, the route should be
installed as onlink. This enables a configuration common in mesh networks
where the mesh interface is assigned a /32 and babel handles the routing by
installing onlink routes.
This issue has a long history. In 2012, we changed data field for
unnumbered PtP links from iface id (specified by RFC) to IP address based
on reports of bugs in Quagga that required it, and we used out-of-band
information to distinquish unnumberred PtPs with the same local IP
address.
Then with OSPF graceful restart implementation, we found that we can no
longer use out-of-band information, and we need to use only LSAdb info
for routing table calculation, but i forgot to finish handling of this
case, so multiple unnumbered PtPs with the same local IP addresses were
broken.
Considering that even recent Mikrotik RouterOS has broken next hop
calculation that depends on IP address in PtP link data field, we
cannot just switch back to the iface id for unnumbered PtP links.
The patch makes two changes: First, it goes back to use out-of-band
(position) info for distinguishing local interfaces in SPF when graceful
restart is not enabled, while still uses LSAdb-only approach for SPF
calculation when graceful restart is enabled.
Second, it adds OSPF interface option 'ptp address', which controls
whether IP address or iface id is used in data field. It is enabled
by default except for unnumbered PtP links with enabled graceful
restart.
Thanks to Kenth Eriksson for the bugreport and Joakim Tjernlund for
suggestions.
There is nothing in RFCs specifying that id 0 is not allowed. Some
implementations does not support it, while some other use key id 0 by
default. We allow it but start with key id 1 by default.
Implement regex-like '+' operator in BGP path masks to match previous
path mask item multiple times. This is useful as ASNs may appear
multiple times in paths due to path prepending for traffic engineering
purposes.
BGP: Fix handling of strange IPv6 link-local-only next hops
There are three common ways how to encode IPv6 link-local-only next hops:
(:: ll), (ll), and (ll ll). We use the first one but we should accept all
three. The patch fixes handling of the last one.
The RFC 5575 does not explicitly reject flowspec rules without dst part,
it just requires dst part in validation procedure for feasibility, which
we do not implement anyway. Thus flow without dst prefix is syntactically
valid, but unfeasible (if feasibilty testing is done).
BGP: Support for MD5SIG together with remote range
When dynamic BGP with remote range is configured, MD5SIG needs to use
newer socket option (TCP_MD5SIG_EXT) to specify remote addres range for
listening socket.
Recent changes in neighbor code caused RIP to access neighbor field which
is NULL during interface/neighbor removal and caused crash when debug
messages are enabled. Use correct field to get iface from neighbor.
KRT: Improve syncer code to avoid using temporary data in rtable
The old code stored route verdicts and temporary routes directly in
rtable. The new code do not store received routes (it immediately
compares them with exported routes and resolves conflicts) and uses
internal bitmap to keep track of which routes were received and which
needs to be reinstalled.
By not putting 'invalid' temporary routes to rtable, we keep rtable
in consistent state, therefore scan no longer needs to be atomic
operation and could be splitted to multiple events.
Initial parsing of test.conf must be done directly in filter_test main,
while reconfiguration is handled as a regular test. Also fix several
minor issues in test code.
Channel currently does not have independent pool and uses protocol pool,
which is freed when protocol changes state to down, while channel is
still in flushing. Move some some cleanup code to channel_do_flush()
so it is done before freeing of protocol pool.
projects / thirdparty / bird.git / log
