The custom rate constraint lists were necessary to support 12kHz and 24kHz.
These rates are now available through SNDRV_PCM_RATE_12000 and
SNDRV_PCM_RATE_24000.
Use them and drop the custom rate constraint rules.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: David Rhodes <drhodes@opensource.cirrus.com> Acked-by: Mark Brown <broonie@kernel.org> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://patch.msgid.link/20240905-alsa-12-24-128-v1-3-8371948d3921@baylibre.com
This adds a sample rate definition for 12kHz, 24kHz and 128kHz.
Admittedly, just a few drivers are currently using these sample
rates but there is enough of a recurrence to justify adding a definition
for them and remove some custom rate constraint code while at it.
The new definitions are not added to the interval definitions, such as
SNDRV_PCM_RATE_8000_44100, because it would silently add new supported
rates to drivers that may or may not support them. For sure the drivers
have not been tested for these new rates so it is better to leave them out
of interval definitions.
That being said, the added rates are multiples of well know rates families,
it is very likely that a lot of devices out there actually supports them.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: David Rhodes <drhodes@opensource.cirrus.com> Acked-by: Mark Brown <broonie@kernel.org> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://patch.msgid.link/20240905-alsa-12-24-128-v1-1-8371948d3921@baylibre.com
ALSA: usb-audio: Add mixer quirk for RME Digiface USB
Implement sync, output format, and input status mixer controls, to allow
the interface to be used as a straight ADAT/SPDIF (+ Headphones) I/O
interface.
This does not implement the matrix mixer, output gain controls, or input
level meter feedback. The full mixer interface is only really usable
using a dedicated userspace control app (there are too many mixer nodes
for alsamixer to be usable), so for now we leave it up to userspace to
directly control these features using raw USB control messages. This is
similar to how it's done with some FireWire interfaces (ffado-mixer).
Add trivial support for audio streaming on the RME Digiface USB. Binds
only to the first interface to allow userspace to directly drive the
complex I/O and matrix mixer controls.
ALSA: hda/realtek: extend quirks for Clevo V5[46]0
The mic in those laptops suffers too high gain resulting in mostly (fan
or else) noise being recorded. In addition to the existing fixup about
mic detection, apply also limiting its boost. While at it, extend the
quirk to also V5[46]0TNE models, which have the same issue.
ALSA: core: Drop superfluous no_free_ptr() for memdup_user() errors
We used to wrap with no_free_ptr() for the return value from
memdup_user() with errors where the auto cleanup is applied. This was
a workaround because the initial implementation of kfree auto-cleanup
checked only NULL pointers.
Since recently, though, the kfree auto-cleanup checks with
IS_ERR_OR_NULL() (by the commit cd7eb8f83fcf ("mm/slab: make
__free(kfree) accept error pointers")), hence those workarounds became
superfluous. Let's drop them now.
ALSA: pcm: Fix the previous conversion to kstrtoul()
The previous replacement from simple_strtoul() to kstrtoul() forgot
that the passed pointer must be an unsigned long int pointer, while
the value used there is a sized_t pointer. Fix it.
Hongbo Li [Sat, 31 Aug 2024 08:06:39 +0000 (16:06 +0800)]
ALSA: pcm: replace simple_strtoul to kstrtoul
As mentioned in [1], "...simple_strtol(), simple_strtoll(),
simple_strtoul(), and simple_strtoull() functions explicitly
ignore overflows, which may lead to unexpected results in callers."
Hence, the use of those functions is discouraged.
This patch replace the use of the simple_strtoul with the safer
alternatives kstrtoul.
Terry Cheong [Thu, 29 Aug 2024 20:11:53 +0000 (04:11 +0800)]
ALSA: hda/realtek: add patch for internal mic in Lenovo V145
Lenovo V145 is having phase inverted dmic but simply applying inverted
dmic fixups does not work. Chaining up verb fixes for ALC283 enables
inverting dmic fixup to work properly.
We do not need model specific HDA quirks to construct the component
binding details of Cirrus Logic companion amplifiers as this information
is already present in the ACPI.
Quirks are then only required for special workarounds not described in
the ACPI such as internal configuration of the Realtek codecs.
The codec pointer is now initialized in hda_component_manager_init() so
that we can detect when companion amplifiers are found in the ACPI but
the SSID invokes a quirk that also attempts to create the component
binding.
ALSA: hda/conexant: Add pincfg quirk to enable top speakers on Sirius devices
The Sirius notebooks have two sets of speakers 0x17 (sides) and
0x1d (top center). The side speakers are active by default but
the top speakers aren't.
This patch provides a pincfg quirk to activate the top speakers.
Takashi Iwai [Wed, 7 Aug 2024 15:27:23 +0000 (17:27 +0200)]
ALSA: pcm: Drop PCM vmalloc buffer helpers
As the last-standing user of PCM vmalloc buffer helper API took its
own buffer management, we can finally drop those API functions, which
were leftover after reorganization of ALSA memalloc code.
Takashi Iwai [Wed, 7 Aug 2024 15:27:22 +0000 (17:27 +0200)]
drm/bridge: dw-hdmi: Move vmalloc PCM buffer management into the driver
The dw-hdmi drm bridge driver is the only one who still uses the ALSA
vmalloc helper API functions. A previous attempt to change the way of
buffer management wasn't taken for this legacy stuff, as we had little
chance for test and some risk of major breaking.
Instead, this patch moves the vmalloc buffer stuff into the dw-hdmi
driver code itself, so that we can drop them from ALSA core code
afterwards.
ALSA: hda: hda_component: Fix mutex crash if nothing ever binds
Move the initialization of parent->mutex into
hda_component_manager_init() so that it is always valid.
In hda_component_manager_bind() do not clear the parent information.
Only zero-fill the per-component data ready for it to be filled in
by the components as they bind.
Previously parent->mutex was being initialized only in
hda_component_manager_bind(). This meant that it was only
initialized if all components appeared and there was a bind callback.
If there wasn't a bind the mutex object was not valid when the
Realtek driver called any of the other functions.
ALSA: hda/realtek: support HP Pavilion Aero 13-bg0xxx Mute LED
This patch adds the HP Pavilion Aero 13 (13-bg0xxx) (year 2024) to list of
quirks for keyboard LED mute indication.
The laptop has two LEDs (one for speaker and one for mic mute). The
pre-existing quirk ALC245_FIXUP_HP_X360_MUTE_LEDS chains both the quirk for
mic and speaker mute.
Tested on 6.11.0-rc4 with the aforementioned laptop.
Takashi Iwai [Fri, 23 Aug 2024 06:26:08 +0000 (08:26 +0200)]
Merge tag 'asoc-fix-v6.11-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.11
A relatively large collection of fixes here, all driver specific and
none of them particularly major, plus one MAINTAINERS update. There's
been a bunch of work on module autoloading from several people.
If the timestamp of a calibration entry is 0 it is an unused entry and
must be ignored.
Some end-products reserve EFI space for calibration entries by shipping
with a zero-filled EFI file. When searching the file for calibration
data the driver must skip the empty entries. The timestamp of a valid
entry is always non-zero.
ASoC: cs-amp-lib-test: Force test calibration blob entries to be valid
For a normal calibration blob the calTarget values must be non-zero and
unique, and the calTime values must be non-zero. Don't rely on
get_random_bytes() to be random enough to guarantee this. Force the
calTarget and calTime values to be valid while retaining randomness
in the values.
Kailang Yang [Thu, 22 Aug 2024 08:46:56 +0000 (16:46 +0800)]
ALSA: hda/realtek - FIxed ALC285 headphone no sound
Dell platform with ALC215 ALC285 ALC289 ALC225 ALC295 ALC299, plug
headphone or headset.
It had a chance to get no sound from headphone.
Replace depop procedure will solve this issue.
Simon Trimmer [Mon, 19 Aug 2024 12:37:36 +0000 (12:37 +0000)]
ALSA: hda/realtek: Convert existing CS35L56 products to use autodetect fixup function
The existing CS35L56 products can make use of the fixup function that
works out the component binding details so we can remove the fixed
configuration fixup functions.
Takashi Iwai [Mon, 19 Aug 2024 08:41:53 +0000 (10:41 +0200)]
ALSA: seq: Skip event type filtering for UMP events
UMP events don't use the event type field, hence it's invalid to apply
the filter, which may drop the events unexpectedly.
Skip the event filtering for UMP events, instead.
Linus Torvalds [Sun, 18 Aug 2024 17:19:49 +0000 (10:19 -0700)]
Merge tag 'driver-core-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two driver fixes for regressions from 6.11-rc1 due to the
driver core change making a structure in a driver core callback const.
These were missed by all testing EXCEPT for what Bart happened to be
running, so I appreciate the fixes provided here for some
odd/not-often-used driver subsystems that nothing else happened to
catch.
Both of these fixes have been in linux-next all week with no reported
issues"
* tag 'driver-core-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
mips: sgi-ip22: Fix the build
ARM: riscpc: ecard: Fix the build
Linus Torvalds [Sun, 18 Aug 2024 17:16:34 +0000 (10:16 -0700)]
Merge tag 'char-misc-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc fixes from Greg KH:
"Here are some small char/misc fixes for 6.11-rc4 to resolve reported
problems. Included in here are:
- fastrpc revert of a change that broke userspace
- xillybus fixes for reported issues
Half of these have been in linux-next this week with no reported
problems, I don't know if the last bit of xillybus driver changes made
it in, but they are 'obviously correct' so will be safe :)"
* tag 'char-misc-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
char: xillybus: Check USB endpoints when probing device
char: xillybus: Refine workqueue handling
Revert "misc: fastrpc: Restrict untrusted app to attach to privileged PD"
char: xillybus: Don't destroy workqueue from work item running on it
Linus Torvalds [Sun, 18 Aug 2024 17:10:48 +0000 (10:10 -0700)]
Merge tag 'tty-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.11-rc4 to
resolve some reported problems. Included in here are:
- conmakehash.c userspace build issues
- fsl_lpuart driver fix
- 8250_omap revert for reported regression
- atmel_serial rts flag fix
All of these have been in linux-next this week with no reported
issues"
* tag 'tty-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250_omap: Set the console genpd always on if no console suspend"
tty: atmel_serial: use the correct RTS flag.
tty: vt: conmakehash: remove non-portable code printing comment header
tty: serial: fsl_lpuart: mark last busy before uart_add_one_port
Linus Torvalds [Sun, 18 Aug 2024 16:59:06 +0000 (09:59 -0700)]
Merge tag 'usb-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver fixes from Greg KH:
"Here are some small USB and Thunderbolt driver fixes for 6.11-rc4 to
resolve some reported issues. Included in here are:
- thunderbolt driver fixes for reported problems
- typec driver fixes
- xhci fixes
- new device id for ljca usb driver
All of these have been in linux-next this week with no reported
issues"
* tag 'usb-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Fix Panther point NULL pointer deref at full-speed re-enumeration
usb: misc: ljca: Add Lunar Lake ljca GPIO HID to ljca_gpio_hids[]
Revert "usb: typec: tcpm: clear pd_event queue in PORT_RESET"
usb: typec: ucsi: Fix the return value of ucsi_run_command()
usb: xhci: fix duplicate stall handling in handle_tx_event()
usb: xhci: Check for xhci->interrupters being allocated in xhci_mem_clearup()
thunderbolt: Mark XDomain as unplugged when router is removed
thunderbolt: Fix memory leaks in {port|retimer}_sb_regs_write()
Linus Torvalds [Sun, 18 Aug 2024 15:50:36 +0000 (08:50 -0700)]
Merge tag 'for-6.11-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull more btrfs fixes from David Sterba:
"A more fixes. We got reports that shrinker added in 6.10 still causes
latency spikes and the fixes don't handle all corner cases. Due to
summer holidays we're taking a shortcut to disable it for release
builds and will fix it in the near future.
- only enable extent map shrinker for DEBUG builds, temporary quick
fix to avoid latency spikes for regular builds
- update target inode's ctime on unlink, mandated by POSIX
- properly take lock to read/update block group's zoned variables
- add counted_by() annotations"
* tag 'for-6.11-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: only enable extent map shrinker for DEBUG builds
btrfs: zoned: properly take lock to read/update block group's zoned variables
btrfs: tree-checker: add dev extent item checks
btrfs: update target inode's ctime on unlink
btrfs: send: annotate struct name_cache_entry with __counted_by()
Jann Horn [Tue, 6 Aug 2024 19:51:42 +0000 (21:51 +0200)]
fuse: Initialize beyond-EOF page contents before setting uptodate
fuse_notify_store(), unlike fuse_do_readpage(), does not enable page
zeroing (because it can be used to change partial page contents).
So fuse_notify_store() must be more careful to fully initialize page
contents (including parts of the page that are beyond end-of-file)
before marking the page uptodate.
The current code can leave beyond-EOF page contents uninitialized, which
makes these uninitialized page contents visible to userspace via mmap().
This is an information leak, but only affects systems which do not
enable init-on-alloc (via CONFIG_INIT_ON_ALLOC_DEFAULT_ON=y or the
corresponding kernel command line parameter).
Ivan Orlov [Tue, 13 Aug 2024 12:07:01 +0000 (13:07 +0100)]
selftests: ALSA: Cover userspace-driven timers with test
Add a test for the new functionality of userspace-driven timers and the
tool which allows us to count timer ticks in a certain time period. The
test:
1. Creates a userspace-driven timer with ioctl to /dev/snd/timer
2. Starts the `global-timer` application to count the ticks of the timer
from step 1.
3. Asynchronously triggers the timer multiple times with some interval
4. Compares the amount of caught ticks with the amount of trigger calls.
Since we can't include <alsa/asoundlib.h> and <sound/asound.h> in one
file due to overlapping declarations, I have to split the test into two
applications: one of them counts the amount of timer ticks in the
defined time period, and another one is the actual test which creates
the timer, triggers it periodically and starts the first app to count
the amount of ticks in a separate thread.
Besides from testing the functionality itself, the test represents a
sample application showing userspace-driven ALSA timers API.
Also, the timer test includes a test case which tries to create a timer
with invalid resolution (=0), and NULL as a timer info structure.
Implement two ioctl calls in order to support virtual userspace-driven
ALSA timers.
The first ioctl is SNDRV_TIMER_IOCTL_CREATE, which gets the
snd_timer_uinfo struct as a parameter and puts a file descriptor of a
virtual timer into the `fd` field of the snd_timer_unfo structure. It
also updates the `id` field of the snd_timer_uinfo struct, which
provides a unique identifier for the timer (basically, the subdevice
number which can be used when creating timer instances).
This patch also introduces a tiny id allocator for the userspace-driven
timers, which guarantees that we don't have more than 128 of them in the
system.
Another ioctl is SNDRV_TIMER_IOCTL_TRIGGER, which allows us to trigger
the virtual timer (and calls snd_timer_interrupt for the timer under
the hood), causing all of the timer instances binded to this timer to
execute their callbacks.
The maximum amount of ticks available for the timer is 1 for the sake of
simplicity of the userspace API. 'start', 'stop', 'open' and 'close'
callbacks for the userspace-driven timers are empty since we don't
really do any hardware initialization here.
Ivan Orlov [Tue, 13 Aug 2024 12:06:59 +0000 (13:06 +0100)]
Docs/sound: Add documentation for userspace-driven ALSA timers
Add the documentation which describes the new userspace-driven timers
API introduced in this patch series. The documentation contains:
- Description of userspace-driven ALSA timers, what they are for
- Description of the timers API
- Example of how the timers can be created and triggered
- How the timers can be used as a timer sources for snd-aloop module
Linus Torvalds [Sun, 18 Aug 2024 02:50:16 +0000 (19:50 -0700)]
Merge tag 'mm-hotfixes-stable-2024-08-17-19-34' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"16 hotfixes. All except one are for MM. 10 of these are cc:stable and
the others pertain to post-6.10 issues.
As usual with these merges, singletons and doubletons all over the
place, no identifiable-by-me theme. Please see the lovingly curated
changelogs to get the skinny"
* tag 'mm-hotfixes-stable-2024-08-17-19-34' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/migrate: fix deadlock in migrate_pages_batch() on large folios
alloc_tag: mark pages reserved during CMA activation as not tagged
alloc_tag: introduce clear_page_tag_ref() helper function
crash: fix riscv64 crash memory reserve dead loop
selftests: memfd_secret: don't build memfd_secret test on unsupported arches
mm: fix endless reclaim on machines with unaccepted memory
selftests/mm: compaction_test: fix off by one in check_compaction()
mm/numa: no task_numa_fault() call if PMD is changed
mm/numa: no task_numa_fault() call if PTE is changed
mm/vmalloc: fix page mapping if vm_area_alloc_pages() with high order fallback to order 0
mm/memory-failure: use raw_spinlock_t in struct memory_failure_cpu
mm: don't account memmap per-node
mm: add system wide stats items category
mm: don't account memmap on failure
mm/hugetlb: fix hugetlb vs. core-mm PT locking
mseal: fix is_madv_discard()
Linus Torvalds [Sun, 18 Aug 2024 02:23:02 +0000 (19:23 -0700)]
Merge tag 'powerpc-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix crashes on 85xx with some configs since the recent hugepd rework.
- Fix boot warning with hugepages and CONFIG_DEBUG_VIRTUAL on some
platforms.
- Don't enable offline cores when changing SMT modes, to match existing
userspace behaviour.
Thanks to Christophe Leroy, Dr. David Alan Gilbert, Guenter Roeck, Nysal
Jan K.A, Shrikanth Hegde, Thomas Gleixner, and Tyrel Datwyler.
* tag 'powerpc-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/topology: Check if a core is online
cpu/SMT: Enable SMT only if a core is online
powerpc/mm: Fix boot warning with hugepages and CONFIG_DEBUG_VIRTUAL
powerpc/mm: Fix size of allocated PGDIR
soc: fsl: qbman: remove unused struct 'cgr_comp'
Linus Torvalds [Sat, 17 Aug 2024 23:31:12 +0000 (16:31 -0700)]
Merge tag 'v6.11-rc3-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- fix for clang warning - additional null check
- fix for cached write with posix locks
- flexible structure fix
* tag 'v6.11-rc3-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: smb2pdu.h: Use static_assert() to check struct sizes
smb3: fix lock breakage for cached writes
smb/client: avoid possible NULL dereference in cifs_free_subrequest()
Linus Torvalds [Sat, 17 Aug 2024 23:23:05 +0000 (16:23 -0700)]
Merge tag 'i2c-for-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C core fix replacing IS_ENABLED() with IS_REACHABLE()
For host drivers, there are two fixes:
- Tegra I2C Controller: Addresses a potential double-locking issue
during probe. ACPI devices are not IRQ-safe when invoking runtime
suspend and resume functions, so the irq_safe flag should not be
set.
- Qualcomm GENI I2C Controller: Fixes an oversight in the exit path
of the runtime_resume() function, which was missed in the previous
release"
* tag 'i2c-for-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: tegra: Do not mark ACPI devices as irq safe
i2c: Use IS_REACHABLE() for substituting empty ACPI functions
i2c: qcom-geni: Add missing geni_icc_disable in geni_i2c_runtime_resume
Linus Torvalds [Sat, 17 Aug 2024 17:04:01 +0000 (10:04 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes to the mpi3mr driver. One to avoid oversize
allocations in tracing and the other to fix an uninitialized spinlock
in the user to driver feature request code (used to trigger dumps and
the like)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpi3mr: Avoid MAX_PAGE_ORDER WARNING for buffer allocations
scsi: mpi3mr: Add missing spin_lock_init() for mrioc->trigger_lock
Linus Torvalds [Sat, 17 Aug 2024 16:51:28 +0000 (09:51 -0700)]
Merge tag 'xfs-6.11-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Chandan Babu:
- Check for presence of only 'attr' feature before scrubbing an inode's
attribute fork.
- Restore the behaviour of setting AIL thread to TASK_INTERRUPTIBLE for
long (i.e. 50ms) sleep durations to prevent high load averages.
- Do not allow users to change the realtime flag of a file unless the
datadev and rtdev both support fsdax access modes.
* tag 'xfs-6.11-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: conditionally allow FS_XFLAG_REALTIME changes if S_DAX is set
xfs: revert AIL TASK_KILLABLE threshold
xfs: attr forks require attr, not attr2
Linus Torvalds [Sat, 17 Aug 2024 16:46:10 +0000 (09:46 -0700)]
Merge tag 'bcachefs-2024-08-16' of git://evilpiepirate.org/bcachefs
Pull bcachefs fixes from Kent OverstreetL
- New on disk format version, bcachefs_metadata_version_disk_accounting_inum
This adds one more disk accounting counter, which counts disk usage
and number of extents per inode number. This lets us track
fragmentation, for implementing defragmentation later, and it also
counts disk usage per inode in all snapshots, which will be a useful
thing to expose to users.
- One performance issue we've observed is threads spinning when they
should be waiting for dirty keys in the key cache to be flushed by
journal reclaim, so we now have hysteresis for the waiting thread, as
well as improving the tracepoint and a new time_stat, for tracking
time blocked waiting on key cache flushing.
... and various assorted smaller fixes.
* tag 'bcachefs-2024-08-16' of git://evilpiepirate.org/bcachefs:
bcachefs: Fix locking in __bch2_trans_mark_dev_sb()
bcachefs: fix incorrect i_state usage
bcachefs: avoid overflowing LRU_TIME_BITS for cached data lru
bcachefs: Fix forgetting to pass trans to fsck_err()
bcachefs: Increase size of cuckoo hash table on too many rehashes
bcachefs: bcachefs_metadata_version_disk_accounting_inum
bcachefs: Kill __bch2_accounting_mem_mod()
bcachefs: Make bkey_fsck_err() a wrapper around fsck_err()
bcachefs: Fix warning in __bch2_fsck_err() for trans not passed in
bcachefs: Add a time_stat for blocked on key cache flush
bcachefs: Improve trans_blocked_journal_reclaim tracepoint
bcachefs: Add hysteresis to waiting on btree key cache flush
lib/generic-radix-tree.c: Fix rare race in __genradix_ptr_alloc()
bcachefs: Convert for_each_btree_node() to lockrestart_do()
bcachefs: Add missing downgrade table entry
bcachefs: disk accounting: ignore unknown types
bcachefs: bch2_accounting_invalid() fixup
bcachefs: Fix bch2_trigger_alloc when upgrading from old versions
bcachefs: delete faulty fastpath in bch2_btree_path_traverse_cached()
Linus Torvalds [Sat, 17 Aug 2024 00:02:32 +0000 (17:02 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix the arm64 __get_mem_asm() to use the _ASM_EXTABLE_##type##ACCESS()
macro instead of the *_ERR() one in order to avoid writing -EFAULT to
the value register in case of a fault
- Initialise all elements of the acpi_early_node_map[] to NUMA_NO_NODE.
Prior to this fix, only the first element was initialised
- Move the KASAN random tag seed initialisation after the per-CPU areas
have been initialised (prng_state is __percpu)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix KASAN random tag seed initialization
arm64: ACPI: NUMA: initialize all values of acpi_early_node_map to NUMA_NO_NODE
arm64: uaccess: correct thinko in __get_mem_asm()
Linus Torvalds [Fri, 16 Aug 2024 23:59:05 +0000 (16:59 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One fix for the new T-Head TH1520 clk driver that marks a bus clk
critical so that it isn't turned off during late init which breaks
emmc-sdio"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: thead: fix dependency on clk_ignore_unused
Linus Torvalds [Fri, 16 Aug 2024 21:03:31 +0000 (14:03 -0700)]
Merge tag 'block-6.11-20240824' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- Fix corruption issues with s390/dasd (Eric, Stefan)
- Fix a misuse of non irq locking grab of a lock (Li)
- MD pull request with a single data corruption fix for raid1 (Yu)
* tag 'block-6.11-20240824' of git://git.kernel.dk/linux:
block: Fix lockdep warning in blk_mq_mark_tag_wait
md/raid1: Fix data corruption for degraded array with slow disk
s390/dasd: fix error recovery leading to data corruption on ESE devices
s390/dasd: Remove DMA alignment
Linus Torvalds [Fri, 16 Aug 2024 21:00:05 +0000 (14:00 -0700)]
Merge tag 'io_uring-6.11-20240824' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
- Fix a comment in the uapi header using the wrong member name (Caleb)
- Fix KCSAN warning for a debug check in sqpoll (me)
- Two more NAPI tweaks (Olivier)
* tag 'io_uring-6.11-20240824' of git://git.kernel.dk/linux:
io_uring: fix user_data field name in comment
io_uring/sqpoll: annotate debug task == current with data_race()
io_uring/napi: remove duplicate io_napi_entry timeout assignation
io_uring/napi: check napi_enabled in io_napi_add() before proceeding
Qu Wenruo [Fri, 16 Aug 2024 01:10:38 +0000 (10:40 +0930)]
btrfs: only enable extent map shrinker for DEBUG builds
Although there are several patches improving the extent map shrinker,
there are still reports of too frequent shrinker behavior, taking too
much CPU for the kswapd process.
So let's only enable extent shrinker for now, until we got more
comprehensive understanding and a better solution.
Linus Torvalds [Fri, 16 Aug 2024 18:49:07 +0000 (11:49 -0700)]
Merge tag 'thermal-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fix from Rafael Wysocki:
"Fix a Bang-bang thermal governor issue causing it to fail to reset the
state of cooling devices if they are 'on' to start with, but the
thermal zone temperature is always below the corresponding trip point
(Rafael Wysocki)"
* tag 'thermal-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: gov_bang_bang: Use governor_data to reduce overhead
thermal: gov_bang_bang: Add .manage() callback
thermal: gov_bang_bang: Split bang_bang_control()
thermal: gov_bang_bang: Call __thermal_cdev_update() directly
Linus Torvalds [Fri, 16 Aug 2024 18:43:54 +0000 (11:43 -0700)]
Merge tag 'acpi-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix an issue related to the ACPI EC device handling that causes the
_REG control method to be evaluated for EC operation regions that are
not expected to be used.
This confuses the platform firmware and provokes various types of
misbehavior on some systems (Rafael Wysocki)"
* tag 'acpi-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: EC: Evaluate _REG outside the EC scope more carefully
ACPICA: Add a depth argument to acpi_execute_reg_methods()
Revert "ACPI: EC: Evaluate orphan _REG under EC device"
Linus Torvalds [Fri, 16 Aug 2024 18:36:40 +0000 (11:36 -0700)]
Merge tag 'libnvdimm-fixes-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fix from Ira Weiny:
"Commit f467fee48da4 ("block: move the dax flag to queue_limits") broke
the DAX tests by skipping over the legacy pmem mapping pages case.
Set the DAX flag in this case as well"
* tag 'libnvdimm-fixes-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nvdimm/pmem: Set dax flag for all 'PFN_MAP' cases
Linus Torvalds [Fri, 16 Aug 2024 18:24:06 +0000 (11:24 -0700)]
Merge tag 'rust-fixes-6.11' of https://github.com/Rust-for-Linux/linux
Pull rust fixes from Miguel Ojeda:
- Fix '-Os' Rust 1.80.0+ builds adding more intrinsics (also tweaked in
upstream Rust for the upcoming 1.82.0).
- Fix support for the latest version of rust-analyzer due to a change
on rust-analyzer config file semantics (considered a fix since most
developers use the latest version of the tool, which is the only one
actually supported by upstream). I am discussing stability of the
config file with upstream -- they may be able to start versioning it.
- Fix GCC 14 builds due to '-fmin-function-alignment' not skipped for
libclang (bindgen).
- A couple Kconfig fixes around '{RUSTC,BINDGEN}_VERSION_TEXT' to
suppress error messages in a foreign architecture chroot and to use a
proper default format.
- Clean 'rust-analyzer' target warning due to missing recursive make
invocation mark.
- Clean Clippy warning due to missing indentation in docs.
- Clean LLVM 19 build warning due to removed 3dnow feature upstream.
* tag 'rust-fixes-6.11' of https://github.com/Rust-for-Linux/linux:
rust: x86: remove `-3dnow{,a}` from target features
kbuild: rust-analyzer: mark `rust_is_available.sh` invocation as recursive
rust: add intrinsics to fix `-Os` builds
kbuild: rust: skip -fmin-function-alignment in bindgen flags
rust: Support latest version of `rust-analyzer`
rust: macros: indent list item in `module!`'s docs
rust: fix the default format for CONFIG_{RUSTC,BINDGEN}_VERSION_TEXT
rust: suppress error messages from CONFIG_{RUSTC,BINDGEN}_VERSION_TEXT
Linus Torvalds [Fri, 16 Aug 2024 18:18:09 +0000 (11:18 -0700)]
Merge tag 'riscv-for-linus-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- reintroduce the text patching global icache flush
- fix syscall entry code to correctly initialize a0, which manifested
as a strace bug
- XIP kernels now map the entire kernel, which fixes boot under at
least DEBUG_VIRTUAL=y
- initialize all nodes in the acpi_early_node_map initializer
- fix OOB access in the Andes vendor extension probing code
- A new key for scalar misaligned access performance in hwprobe, which
correctly treat the values as an enum (as opposed to a bitmap)
* tag 'riscv-for-linus-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix out-of-bounds when accessing Andes per hart vendor extension array
RISC-V: hwprobe: Add SCALAR to misaligned perf defines
RISC-V: hwprobe: Add MISALIGNED_PERF key
RISC-V: ACPI: NUMA: initialize all values of acpi_early_node_map to NUMA_NO_NODE
riscv: change XIP's kernel_map.size to be size of the entire kernel
riscv: entry: always initialize regs->a0 to -ENOSYS
riscv: Re-introduce global icache flush in patch_text_XXX()
Linus Torvalds [Fri, 16 Aug 2024 18:12:29 +0000 (11:12 -0700)]
Merge tag 'trace-v6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
"A couple of fixes for tracing:
- Prevent a NULL pointer dereference in the error path of RTLA tool
- Fix an infinite loop bug when reading from the ring buffer when
closed. If there's a thread trying to read the ring buffer and it
gets closed by another thread, the one reading will go into an
infinite loop when the buffer is empty instead of exiting back to
user space"
* tag 'trace-v6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
rtla/osnoise: Prevent NULL dereference in error handling
tracing: Return from tracing_buffers_read() if the file has been closed
Linus Torvalds [Fri, 16 Aug 2024 15:56:45 +0000 (08:56 -0700)]
Merge tag 'iommu-fixes-v6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu fixes from Joerg Roedel:
- Bring back a lost return statement in io-page-fault code
- Remove an unused function declaration
* tag 'iommu-fixes-v6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
iommu: Remove unused declaration iommu_sva_unbind_gpasid()
iommu: Restore lost return in iommu_report_device_fault()
Linus Torvalds [Fri, 16 Aug 2024 15:39:41 +0000 (08:39 -0700)]
Merge tag 'sound-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All small fixes, mostly for usual suspects, HD-audio and USB-audio
device-specific fixes / quirks. The Cirrus codec support took the
update of SPI header as well. Other than that, there is a regression
fix in the sanity check of ALSA timer code"
* tag 'sound-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/tas2781: Use correct endian conversion
ALSA: usb-audio: Support Yamaha P-125 quirk entry
ALSA: hda: cs35l41: Remove redundant call to hda_cs_dsp_control_remove()
ALSA: hda: cs35l56: Remove redundant call to hda_cs_dsp_control_remove()
ALSA: hda/tas2781: fix wrong calibrated data order
ALSA: usb-audio: Add delay quirk for VIVO USB-C-XE710 HEADSET
ALSA: hda/realtek: Add support for new HP G12 laptops
ALSA: hda/realtek: Fix noise from speakers on Lenovo IdeaPad 3 15IAU7
ALSA: timer: Relax start tick time check for slave timer elements
spi: Add empty versions of ACPI functions
Linus Torvalds [Fri, 16 Aug 2024 15:35:50 +0000 (08:35 -0700)]
Merge tag 'drm-fixes-2024-08-16' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Weekly drm fixes, mostly amdgpu and xe. The larger amdgpu fix is for a
new IP block introduced in rc1, so should be fine. The xe fixes
contain some missed fixes from the end of the previous round along
with some fixes which required precursor changes, but otherwise
everything seems fine,
xe:
- Validate user fence during creation
- Fix use after free when client stats are captured
- SRIOV fixes
- Runtime PM fixes"
* tag 'drm-fixes-2024-08-16' of https://gitlab.freedesktop.org/drm/kernel: (37 commits)
drm/xe: Hold a PM ref when GT TLB invalidations are inflight
drm/xe: Drop xe_gt_tlb_invalidation_wait
drm/xe: Add xe_gt_tlb_invalidation_fence_init helper
drm/xe/pf: Fix VF config validation on multi-GT platforms
drm/xe: Build PM into GuC CT layer
drm/xe/vf: Fix register value lookup
drm/xe: Fix use after free when client stats are captured
drm/xe: Take a ref to xe file when user creates a VM
drm/xe: Add ref counting for xe_file
drm/xe: Move part of xe_file cleanup to a helper
drm/xe: Validate user fence during creation
drm/rockchip: inno-hdmi: Fix infoframe upload
drm/amd/amdgpu: add HDP_SD support on gc 12.0.0/1
drm/amdgpu: Update kmd_fw_shared for VCN5
drm/amd/amdgpu: command submission parser for JPEG
drm/amdgpu/mes12: fix suspend issue
drm/amdgpu/mes12: sw/hw fini for unified mes
drm/amdgpu/mes12: configure two pipes hardware resources
drm/amdgpu/mes12: adjust mes12 sw/hw init for multiple pipes
drm/amdgpu/mes12: add mes pipe switch support
...
Wolfram Sang [Fri, 16 Aug 2024 14:23:51 +0000 (16:23 +0200)]
Merge tag 'i2c-host-fixes-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
Two fixes in this update:
Tegra I2C Controller: Addresses a potential double-locking issue
during probe. ACPI devices are not IRQ-safe when invoking runtime
suspend and resume functions, so the irq_safe flag should not be
set.
Qualcomm GENI I2C Controller: Fixes an oversight in the exit path
of the runtime_resume() function, which was missed in the
previous release.
Vijendar Mukunda [Fri, 16 Aug 2024 07:03:28 +0000 (12:33 +0530)]
ASoC: SOF: amd: Fix for acp init sequence
When ACP is not powered on by default, acp power on sequence explicitly
invoked by programming pgfsm control mask. The existing implementation
checks the same PGFSM status mask and programs the same PGFSM control mask
in all ACP variants which breaks acp power on sequence for ACP6.0 and
ACP6.3 variants. So to fix this issue, update ACP pgfsm control mask and
status mask based on acp descriptor rev field, which will vary based on
acp variant.
thermal: gov_bang_bang: Use governor_data to reduce overhead
After running once, the for_each_trip_desc() loop in
bang_bang_manage() is pure needless overhead because it is not going to
make any changes unless a new cooling device has been bound to one of
the trips in the thermal zone or the system is resuming from sleep.
For this reason, make bang_bang_manage() set governor_data for the
thermal zone and check it upfront to decide whether or not it needs to
do anything.
However, governor_data needs to be reset in some cases to let
bang_bang_manage() know that it should walk the trips again, so add an
.update_tz() callback to the governor and make the core additionally
invoke it during system resume.
To avoid affecting the other users of that callback unnecessarily, add
a special notification reason for system resume, THERMAL_TZ_RESUME, and
also pass it to __thermal_zone_device_update() called during system
resume for consistency.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Kästle <peter@piie.net> Reviewed-by: Zhang Rui <rui.zhang@intel.com> Cc: 6.10+ <stable@vger.kernel.org> # 6.10+ Link: https://patch.msgid.link/2285575.iZASKD2KPV@rjwysocki.net
After recent changes, the Bang-bang governor may not adjust the
initial configuration of cooling devices to the actual situation.
Namely, if a cooling device bound to a certain trip point starts in
the "on" state and the thermal zone temperature is below the threshold
of that trip point, the trip point may never be crossed on the way up
in which case the state of the cooling device will never be adjusted
because the thermal core will never invoke the governor's
.trip_crossed() callback. [Note that there is no issue if the zone
temperature is at the trip threshold or above it to start with because
.trip_crossed() will be invoked then to indicate the start of thermal
mitigation for the given trip.]
To address this, add a .manage() callback to the Bang-bang governor
and use it to ensure that all of the thermal instances managed by the
governor have been initialized properly and the states of all of the
cooling devices involved have been adjusted to the current zone
temperature as appropriate.
Move the setting of the thermal instance target state from
bang_bang_control() into a separate function that will be also called
in a different place going forward.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Kästle <peter@piie.net> Reviewed-by: Zhang Rui <rui.zhang@intel.com> Cc: 6.10+ <stable@vger.kernel.org> # 6.10+ Link: https://patch.msgid.link/3313587.aeNJFYEL58@rjwysocki.net
Instead of clearing the "updated" flag for each cooling device
affected by the trip point crossing in bang_bang_control() and
walking all thermal instances to run thermal_cdev_update() for all
of the affected cooling devices, call __thermal_cdev_update()
directly for each of them.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Kästle <peter@piie.net> Reviewed-by: Zhang Rui <rui.zhang@intel.com> Cc: 6.10+ <stable@vger.kernel.org> # 6.10+ Link: https://patch.msgid.link/13583081.uLZWGnKmhe@rjwysocki.net
Eli Billauer [Fri, 16 Aug 2024 07:02:00 +0000 (10:02 +0300)]
char: xillybus: Check USB endpoints when probing device
Ensure, as the driver probes the device, that all endpoints that the
driver may attempt to access exist and are of the correct type.
All XillyUSB devices must have a Bulk IN and Bulk OUT endpoint at
address 1. This is verified in xillyusb_setup_base_eps().
On top of that, a XillyUSB device may have additional Bulk OUT
endpoints. The information about these endpoints' addresses is deduced
from a data structure (the IDT) that the driver fetches from the device
while probing it. These endpoints are checked in setup_channels().
A XillyUSB device never has more than one IN endpoint, as all data
towards the host is multiplexed in this single Bulk IN endpoint. This is
why setup_channels() only checks OUT endpoints.
Reported-by: syzbot+eac39cba052f2e750dbe@syzkaller.appspotmail.com Cc: stable <stable@kernel.org> Closes: https://lore.kernel.org/all/0000000000001d44a6061f7a54ee@google.com/T/ Fixes: a53d1202aef1 ("char: xillybus: Add driver for XillyUSB (Xillybus variant for USB)"). Signed-off-by: Eli Billauer <eli.billauer@gmail.com> Link: https://lore.kernel.org/r/20240816070200.50695-2-eli.billauer@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mm/migrate: fix deadlock in migrate_pages_batch() on large folios
Currently, migrate_pages_batch() can lock multiple locked folios with an
arbitrary order. Although folio_trylock() is used to avoid deadlock as
commit 2ef7dbb26990 ("migrate_pages: try migrate in batch asynchronously
firstly") mentioned, it seems try_split_folio() is still missing.
It was found by compaction stress test when I explicitly enable EROFS
compressed files to use large folios, which case I cannot reproduce with
the same workload if large folio support is off (current mainline).
Typically, filesystem reads (with locked file-backed folios) could use
another bdev/meta inode to load some other I/Os (e.g. inode extent
metadata or caching compressed data), so the locking order will be:
file-backed folios (A)
bdev/meta folios (B)
The following calltrace shows the deadlock:
Thread 1 takes (B) lock and tries to take folio (A) lock
Thread 2 takes (A) lock and tries to take folio (B) lock
[Thread 1]
INFO: task stress:1824 blocked for more than 30 seconds.
Tainted: G OE 6.10.0-rc7+ #6
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:stress state:D stack:0 pid:1824 tgid:1824 ppid:1822 flags:0x0000000c
Call trace:
__switch_to+0xec/0x138
__schedule+0x43c/0xcb0
schedule+0x54/0x198
io_schedule+0x44/0x70
folio_wait_bit_common+0x184/0x3f8
<-- folio mapping ffff00036d69cb18 index 996 (**)
__folio_lock+0x24/0x38
migrate_pages_batch+0x77c/0xea0 // try_split_folio (mm/migrate.c:1486:2)
// migrate_pages_batch (mm/migrate.c:1734:16)
<--- LIST_HEAD(unmap_folios) has
..
folio mapping 0xffff0000d184f1d8 index 1711; (*)
folio mapping 0xffff0000d184f1d8 index 1712;
..
migrate_pages+0xb28/0xe90
compact_zone+0xa08/0x10f0
compact_node+0x9c/0x180
sysctl_compaction_handler+0x8c/0x118
proc_sys_call_handler+0x1a8/0x280
proc_sys_write+0x1c/0x30
vfs_write+0x240/0x380
ksys_write+0x78/0x118
__arm64_sys_write+0x24/0x38
invoke_syscall+0x78/0x108
el0_svc_common.constprop.0+0x48/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x3c/0x148
el0t_64_sync_handler+0x100/0x130
el0t_64_sync+0x190/0x198
[Thread 2]
INFO: task stress:1825 blocked for more than 30 seconds.
Tainted: G OE 6.10.0-rc7+ #6
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:stress state:D stack:0 pid:1825 tgid:1825 ppid:1822 flags:0x0000000c
Call trace:
__switch_to+0xec/0x138
__schedule+0x43c/0xcb0
schedule+0x54/0x198
io_schedule+0x44/0x70
folio_wait_bit_common+0x184/0x3f8
<-- folio = 0xfffffdffc6b503c0 (mapping == 0xffff0000d184f1d8 index == 1711) (*)
__folio_lock+0x24/0x38
z_erofs_runqueue+0x384/0x9c0 [erofs]
z_erofs_readahead+0x21c/0x350 [erofs] <-- folio mapping 0xffff00036d69cb18 range from [992, 1024] (**)
read_pages+0x74/0x328
page_cache_ra_order+0x26c/0x348
ondemand_readahead+0x1c0/0x3a0
page_cache_sync_ra+0x9c/0xc0
filemap_get_pages+0xc4/0x708
filemap_read+0x104/0x3a8
generic_file_read_iter+0x4c/0x150
vfs_read+0x27c/0x330
ksys_pread64+0x84/0xd0
__arm64_sys_pread64+0x28/0x40
invoke_syscall+0x78/0x108
el0_svc_common.constprop.0+0x48/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x3c/0x148
el0t_64_sync_handler+0x100/0x130
el0t_64_sync+0x190/0x198
Link: https://lkml.kernel.org/r/20240729021306.398286-1-hsiangkao@linux.alibaba.com Fixes: 5dfab109d519 ("migrate_pages: batch _unmap and _move") Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com> Reviewed-by: "Huang, Ying" <ying.huang@intel.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
alloc_tag: mark pages reserved during CMA activation as not tagged
During CMA activation, pages in CMA area are prepared and then freed
without being allocated. This triggers warnings when memory allocation
debug config (CONFIG_MEM_ALLOC_PROFILING_DEBUG) is enabled. Fix this by
marking these pages not tagged before freeing them.
Link: https://lkml.kernel.org/r/20240813150758.855881-2-surenb@google.com Fixes: d224eb0287fb ("codetag: debug: mark codetags for reserved pages as empty") Signed-off-by: Suren Baghdasaryan <surenb@google.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Kent Overstreet <kent.overstreet@linux.dev> Cc: Pasha Tatashin <pasha.tatashin@soleen.com> Cc: Sourav Panda <souravpanda@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> [6.10] Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
alloc_tag: introduce clear_page_tag_ref() helper function
In several cases we are freeing pages which were not allocated using
common page allocators. For such cases, in order to keep allocation
accounting correct, we should clear the page tag to indicate that the page
being freed is expected to not have a valid allocation tag. Introduce
clear_page_tag_ref() helper function to be used for this.
Link: https://lkml.kernel.org/r/20240813150758.855881-1-surenb@google.com Fixes: d224eb0287fb ("codetag: debug: mark codetags for reserved pages as empty") Signed-off-by: Suren Baghdasaryan <surenb@google.com> Suggested-by: David Hildenbrand <david@redhat.com> Acked-by: David Hildenbrand <david@redhat.com> Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com> Cc: Kees Cook <keescook@chromium.org> Cc: Kent Overstreet <kent.overstreet@linux.dev> Cc: Sourav Panda <souravpanda@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> [6.10] Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Jinjie Ruan [Mon, 12 Aug 2024 06:20:17 +0000 (14:20 +0800)]
crash: fix riscv64 crash memory reserve dead loop
On RISCV64 Qemu machine with 512MB memory, cmdline "crashkernel=500M,high"
will cause system stall as below:
Zone ranges:
DMA32 [mem 0x0000000080000000-0x000000009fffffff]
Normal empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000080000000-0x000000008005ffff]
node 0: [mem 0x0000000080060000-0x000000009fffffff]
Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
(stall here)
commit 5d99cadf1568 ("crash: fix x86_32 crash memory reserve dead loop
bug") fix this on 32-bit architecture. However, the problem is not
completely solved. If `CRASH_ADDR_LOW_MAX = CRASH_ADDR_HIGH_MAX` on
64-bit architecture, for example, when system memory is equal to
CRASH_ADDR_LOW_MAX on RISCV64, the following infinite loop will also
occur:
-> reserve_crashkernel_generic() and high is true
-> alloc at [CRASH_ADDR_LOW_MAX, CRASH_ADDR_HIGH_MAX] fail
-> alloc at [0, CRASH_ADDR_LOW_MAX] fail and repeatedly
(because CRASH_ADDR_LOW_MAX = CRASH_ADDR_HIGH_MAX).
As Catalin suggested, do not remove the ",high" reservation fallback to
",low" logic which will change arm64's kdump behavior, but fix it by
skipping the above situation similar to commit d2f32f23190b ("crash: fix
x86_32 crash memory reserve dead loop").
After this patch, it print:
cannot allocate crashkernel (size:0x1f400000)
Link: https://lkml.kernel.org/r/20240812062017.2674441-1-ruanjinjie@huawei.com Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Suggested-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Dave Young <dyoung@redhat.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
selftests: memfd_secret: don't build memfd_secret test on unsupported arches
[1] mentions that memfd_secret is only supported on arm64, riscv, x86 and
x86_64 for now. It doesn't support other architectures. I found the
build error on arm and decided to send the fix as it was creating noise on
KernelCI:
memfd_secret.c: In function 'memfd_secret':
memfd_secret.c:42:24: error: '__NR_memfd_secret' undeclared (first use in this function);
did you mean 'memfd_secret'?
42 | return syscall(__NR_memfd_secret, flags);
| ^~~~~~~~~~~~~~~~~
| memfd_secret
Hence I'm adding condition that memfd_secret should only be compiled on
supported architectures.
Also check in run_vmtests script if memfd_secret binary is present before
executing it.
mm: fix endless reclaim on machines with unaccepted memory
Unaccepted memory is considered unusable free memory, which is not counted
as free on the zone watermark check. This causes get_page_from_freelist()
to accept more memory to hit the high watermark, but it creates problems
in the reclaim path.
The reclaim path encounters a failed zone watermark check and attempts to
reclaim memory. This is usually successful, but if there is little or no
reclaimable memory, it can result in endless reclaim with little to no
progress. This can occur early in the boot process, just after start of
the init process when the only reclaimable memory is the page cache of the
init executable and its libraries.
Make unaccepted memory free from watermark check point of view. This way
unaccepted memory will never be the trigger of memory reclaim. Accept
more memory in the get_page_from_freelist() if needed.
Link: https://lkml.kernel.org/r/20240809114854.3745464-2-kirill.shutemov@linux.intel.com Fixes: dcdfdd40fa82 ("mm: Add support for unaccepted memory") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by: Jianxiong Gao <jxgao@google.com> Acked-by: David Hildenbrand <david@redhat.com> Tested-by: Jianxiong Gao <jxgao@google.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@suse.de> Cc: Mike Rapoport (Microsoft) <rppt@kernel.org> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> [6.5+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
projects / thirdparty / kernel / linux.git / log
