The existing logic in tcphy_get_mode() can cause the phy to be
incorrectly configured to USB UFP or DisplayPort mode when
extcon_get_state returns an error code.
extcon_get_state() can return 0, 1, or a negative error code.
It is possible to get into the failing state with an extcon driver
which does not support the extcon connector id specified as the
second argument to extcon_get_state().
There maybe pending USR interrupt before requesting irq, however
uart_add_one_port has not executed, so there will be kernel panic:
[ 0.795668] Unable to handle kernel NULL pointer dereference at virtual addre
ss 0000000000000080
[ 0.802701] Mem abort info:
[ 0.805367] ESR = 0x0000000096000004
[ 0.808950] EC = 0x25: DABT (current EL), IL = 32 bits
[ 0.814033] SET = 0, FnV = 0
[ 0.816950] EA = 0, S1PTW = 0
[ 0.819950] FSC = 0x04: level 0 translation fault
[ 0.824617] Data abort info:
[ 0.827367] ISV = 0, ISS = 0x00000004
[ 0.831033] CM = 0, WnR = 0
[ 0.833866] [0000000000000080] user address but active_mm is swapper
[ 0.839951] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 0.845953] Modules linked in:
[ 0.848869] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.1+g56321e101aca #1
[ 0.855617] Hardware name: Freescale i.MX8MP EVK (DT)
[ 0.860452] pstate: 000000c5 (nzcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.867117] pc : __imx_uart_rxint.constprop.0+0x11c/0x2c0
[ 0.872283] lr : imx_uart_int+0xf8/0x1ec
The issue only happends in the inmate linux when Jailhouse hypervisor
enabled. The test procedure is:
while true; do
jailhouse enable imx8mp.cell
jailhouse cell linux xxxx
sleep 10
jailhouse cell destroy 1
jailhouse disable
sleep 5
done
And during the upper test, press keys to the 2nd linux console.
When `jailhouse cell destroy 1`, the 2nd linux has no chance to put
the uart to a quiese state, so USR1/2 may has pending interrupts. Then
when `jailhosue cell linux xx` to start 2nd linux again, the issue
trigger.
In order to disable irqs before requesting them, both UCR1 and UCR2 irqs
should be disabled, so here fix that, disable the Ageing Timer interrupt
in UCR2 as UCR1 does.
Fixes: 8a61f0c70ae6 ("serial: imx: Disable irqs before requesting them") Suggested-by: Sherry Sun <sherry.sun@nxp.com> Reviewed-by: Sherry Sun <sherry.sun@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Acked-by: Jason Liu <jason.hui.liu@nxp.com> Link: https://lore.kernel.org/r/20230206013016.29352-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The default polarity of RS485 DE signal is active high. This driver does
not handle such case properly. Currently, when a pin is multiplexed as a
UART CTS_B on boot, this pin is pulled HIGH by the i.MX UART CTS circuit,
which activates DE signal on the RS485 transceiver and thus behave as if
the RS485 was transmitting data, so the system blocks the RS485 bus when
it starts and until user application takes over. This behavior is not OK.
The problem consists of two separate parts.
First, the i.MX UART IP requires UCR1 UARTEN and UCR2 RXEN to be set for
UCR2 CTSC and CTS bits to have any effect. The UCR2 CTSC bit permits the
driver to set CTS (RTS_B or RS485 DE signal) to either level sychronous
to the internal UART IP clock. Compared to other options, like GPIO CTS
control, this has the benefit of being synchronous to the UART IP clock
and thus without glitches or bus delays. The reason for the CTS design
is likely because when the Receiver is disabled, the UART IP can never
indicate that it is ready to receive data by assering CTS signal, so
the CTS is always pulled HIGH by default.
When the port is closed by user space, imx_uart_stop_rx() clears UCR2
RXEN bit, and imx_uart_shutdown() clears UCR1 UARTEN bit. This disables
UART Receiver and UART itself, and forces CTS signal HIGH, which leads
to the RS485 bus being blocked because RS485 DE is incorrectly active.
The proposed solution for this problem is to keep the Receiver running
even after the port is closed, but in loopback mode. This disconnects
the RX FIFO input from the RXD external signal, and since UCR2 TXEN is
cleared, the UART Transmitter is disabled, so nothing can feed data in
the RX FIFO. Because the Receiver is still enabled, the UCR2 CTSC and
CTS bits still have effect and the CTS (RS485 DE) control is retained.
Note that in case of RS485 DE signal active low, there is no problem and
no special handling is necessary. The CTS signal defaults to HIGH, thus
the RS485 is by default set to Receive and the bus is not blocked.
Note that while there is the possibility to control CTS using GPIO with
either CTS polarity, this has the downside of not being synchronous to
the UART IP clock and thus glitchy and susceptible to slow DE switching.
Second, on boot, before the UART driver probe callback is called, the
driver core triggers pinctrl_init_done() and configures the IOMUXC to
default state. At this point, UCR1 UARTEN and UCR2 RXEN are both still
cleared, but UART CTS_B (RS485 DE) is configured as CTS function, thus
the RTS signal is pulled HIGH by the UART IP CTS circuit.
One part of the solution here is to enable UCR1 UARTEN and UCR2 RXEN and
UTS loopback in this driver probe callback, thus unblocking the CTSC and
CTS control early on. But this is still too late, since the pin control
is already configured and CTS has been pulled HIGH for a short period
of time.
When Linux kernel boots and this driver is bound, the pin control is set
to special "init" state if the state is available, and driver can switch
the "default" state afterward when ready. This state can be used to set
the CTS line as a GPIO in DT temporarily, and a GPIO hog can force such
GPIO to LOW, thus keeping the RS485 DE line LOW early on boot. Once the
driver takes over and UCR1 UARTEN and UCR2 RXEN and UTS loopback are all
enabled, the driver can switch to "default" pin control state and control
the CTS line as function instead. DT binding example is below:
The irdma driver can use a maximum number of msix vectors equal
to num_online_cpus() + 1 and the kernel warning stack below is shown
if that number is exceeded.
The kernel throws a warning as the driver tries to update the affinity
hint with a CPU mask greater than the max CPU IDs. Fix this by capping
the MSIX vectors to num_online_cpus() + 1.
To update the I/O pins, the registers are read/modified/written. The
read operation incorrectly always read the first register. Although
wrong, there wasn't any impact as all the output pins are always
written, and the inputs are read only anyway.
Fixes: 2d53139f3162 ("Add support for using a MAX3421E chip as a host driver.") Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Link: https://lore.kernel.org/r/20230207033337.18112-1-mark.tomlinson@alliedtelesis.co.nz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If get_ep_from_tid() fails to lookup non-NULL value for ep, ep is
dereferenced later regardless of whether it is empty.
This patch adds a simple sanity check to fix the issue.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 944661dd97f4 ("RDMA/iw_cxgb4: atomically lookup ep and get a reference") Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Link: https://lore.kernel.org/r/20230202184850.29882-1-n.zhandarovich@fintech.ru Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rn5t618 power driver fails to register
a cooling device because POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT_MAX
is missing but availability is not checked before registering
cooling device. After improved error checking in the thermal
code, the registration of the power supply fails entirely.
Checking for availability of _MAX before registering cooling device
fixes the rn5t618 problem. But the whole logic feels questionable.
First, the logic is inverted here:
the code tells: max_current = max_cooling but
0 = max_cooling, so there needs to be some inversion
in the code which cannot be found. Comparing with other
cooling devices, it can be found that value for fan speed is not
inverted, value for cpufreq cooling is inverted (similar situation
as here lowest frequency = max cooling)
Second, analyzing usage of _MAX: it is seems that maximum capabilities
of charging controller are specified and not of the battery. Probably
there is not too much mismatch in the drivers actually implementing
that. So nothing has exploded yet. So there is no easy and safe way
to specifify a max cooling value now.
Conclusion for now (as a regression fix) just remove the cooling device
registration and do it properly later on.
Fixes: e49a1e1ee078 ("thermal/core: fix error code in __thermal_cooling_device_register()") Fixes: 952aeeb3ee28 ("power_supply: Register power supply for thermal cooling device") Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During enumeration or composition switch,a userspace process
agnostic of the conventions of configs can try to create function
symlinks even after the UDC is bound to current config which is
not correct. Potentially it can create duplicates within the
current config.
Prevent this by adding a check if udc_name already exists, then bail
out of cfg_link.
both the lists corresponds to the same function instance ffs.a
but the usb_function* pointer is different because in step 3
ffs_alloc has created a new reference to usb_function* for
ffs.a and added it to cfg_list.
Step4:
Now a composition switch involving <ffs.b,ffs.a> is executed.
the composition switch will involve 3 things:
1. unlinking the previous functions existing
2. creating new symlinks
3. writing UDC
However, the composition switch is generally taken care by
userspace process which creates the symlinks in its own
nomenclature(X*) and removes only those.
So it won't be able to remove Y1 which user had created
by own.
Due to this the new symlinks cannot be created for ffs.a
since the entry already exists in CFG->FUNC_LIST.
The state of the CFG->FUNC_LIST is as follows:
CFG->FUNC_LIST: <ffs.a>
Fixes: 88af8bbe4ef7 ("usb: gadget: the start of the configfs interface") Signed-off-by: Krishna Kurapati PSSNV <quic_kriskura@quicinc.com> Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com> Link: https://lore.kernel.org/r/20230201132308.31523-1-quic_ugoswami@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the list does not contain the expected element, the value of
list_for_each_entry() iterator will not point to a valid structure.
To avoid type confusion in such case, the list iterator
scope will be limited to list_for_each_entry() loop.
In preparation to limiting scope of a list iterator to the list traversal
loop, use a dedicated pointer to point to the found element [1].
Determining if an element was found is then simply checking if
the pointer is != NULL instead of using the potentially bogus pointer.
This function only calls mtk_otg_switch_init() when the ->port_mode
is MUSB_OTG so the clean up code should only call mtk_otg_switch_exit()
for that mode.
Fixes: 0990366bab3c ("usb: musb: Add support for MediaTek musb controller") Signed-off-by: Dan Carpenter <error27@gmail.com> Link: https://lore.kernel.org/r/Y8/3TqpqiSr0RxFH@kili Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
ip_dev_find() may return NULL and assign it to pdev which is
dereferenced later.
Fix this by checking the return value of ip_dev_find() for NULL
similar to the way it is done with other instances of said function.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1cab775c3e75 ("RDMA/cxgb4: Fix LE hash collision bug for passive open connection") Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Link: https://lore.kernel.org/r/20230201172103.17261-1-n.zhandarovich@fintech.ru Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The RXWATER value must be greater than 0 according to the LPUART
reference manual. And when the number of datawords in the receive
FIFO is greater than RXWATER, an interrupt or a DMA request is
generated, so no need to set the different value for lpuart interrupt
case and dma case. Here delete the wrong RXWATER setting for dma case
directly.
Fixes: 42b68768e51b ("serial: fsl_lpuart: DMA support for 32-bit variant") Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20230130064449.9564-4-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Interleaved DMA transfer support was added by 85e7518f42c8 ("dmaengine:
dw-edma: Add device_prep_interleave_dma() support"), but depending on the
selected channel, either source or destination address are left
uninitialized which was obviously wrong.
Initialize the destination address of the eDMA burst descriptors for
DEV_TO_MEM interleaved operations and the source address for MEM_TO_DEV
operations.
The normal call sequence of using transport class is:
Add path:
transport_setup_device()
transport_setup_classdev() // call sas_host_setup() here
transport_add_device() // if fails, need call transport_destroy_device()
transport_configure_device()
Remove path:
transport_remove_device()
transport_remove_classdev // call sas_host_remove() here
transport_destroy_device()
If transport_add_device() fails, need call transport_destroy_device()
to free memory, but in this case, ->remove() is not called, and the
resources allocated in ->setup() are leaked. So fix these leaks by
calling ->remove() in transport_add_class_device() if it returns error.
Current some drivers(like iscsi) call transport_register_device()
failed, they don't call transport_destroy_device() to release the
memory allocated in transport_setup_device(), because they don't
know what was done, it should be internal thing to release the
resource in register function. So fix this leak by calling destroy
function inside register function.
When calling kobject_add() failed in device_add(), it will call
cleanup_glue_dir() to free resource. But in kobject_add(),
dev->kobj.parent has been set to NULL. This will cause resource leak.
The process is as follows:
device_add()
get_device_parent()
class_dir_create_and_add()
kobject_add() //kobject_get()
...
dev->kobj.parent = kobj;
...
kobject_add() //failed, but set dev->kobj.parent = NULL
...
glue_dir = get_glue_dir(dev) //glue_dir = NULL, and goto
//"Error" label
...
cleanup_glue_dir() //becaues glue_dir is NULL, not call
//kobject_put()
The preceding problem may cause insmod mac80211_hwsim.ko to failed.
sysfs: cannot create duplicate filename '/devices/virtual/mac80211_hwsim'
Call Trace:
<TASK>
dump_stack_lvl+0x8e/0xd1
sysfs_warn_dup.cold+0x1c/0x29
sysfs_create_dir_ns+0x224/0x280
kobject_add_internal+0x2aa/0x880
kobject_add+0x135/0x1a0
get_device_parent+0x3d7/0x590
device_add+0x2aa/0x1cb0
device_create_groups_vargs+0x1eb/0x260
device_create+0xdc/0x110
mac80211_hwsim_new_radio+0x31e/0x4790 [mac80211_hwsim]
init_mac80211_hwsim+0x48d/0x1000 [mac80211_hwsim]
do_one_initcall+0x10f/0x630
do_init_module+0x19f/0x5e0
load_module+0x64b7/0x6eb0
__do_sys_finit_module+0x140/0x200
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
</TASK>
kobject_add_internal failed for mac80211_hwsim with -EEXIST, don't try to
register things with the same name in the same directory.
Fixes: cebf8fd16900 ("driver core: fix race between creating/querying glue dir and its cleanup") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Link: https://lore.kernel.org/r/20221123012042.335252-1-shaozhengchao@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
GUID_INIT() is for internal guid_t type and shouldn't be used
for the uuid_le. I.o.w. relying on the implementation details
is layering violation. Use correct macros to initialize uuid_le.
Fixes: 64e9bbdd9588 ("misc/mei/hdcp: Client driver for HDCP application") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Link: https://lore.kernel.org/r/20221228160500.21220-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to get_user_pages_fast() in vmci_host_setup_notify() can return
NULL context->notify_page causing a GPF. To avoid GPF check if
context->notify_page == NULL and return error if so.
general protection fault, probably for non-canonical address
0xe0009d1000000060: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: maybe wild-memory-access in range [0x0005088000000300-
0x0005088000000307]
CPU: 2 PID: 26180 Comm: repro_34802241 Not tainted 6.1.0-rc4 #1
Hardware name: Red Hat KVM, BIOS 1.15.0-2.module+el8.6.0 04/01/2014
RIP: 0010:vmci_ctx_check_signal_notify+0x91/0xe0
Call Trace:
<TASK>
vmci_host_unlocked_ioctl+0x362/0x1f40
__x64_sys_ioctl+0x1a1/0x230
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
As comment of pci_get_class() says, it returns a pci_device with its
refcount increased and decreased the refcount for the input parameter
@from if it is not NULL.
If we break the loop in applicom_init() with 'dev' not NULL, we need to
call pci_dev_put() to decrease the refcount. Add the missing
pci_dev_put() to avoid refcount leak.
A problem about idt_89hpesx create debugfs failed is triggered with the
following log given:
[ 4973.269647] debugfs: Directory 'idt_csr' with parent '/' already present!
The reason is that idt_init() returns i2c_add_driver() directly without
checking its return value, if i2c_add_driver() failed, it returns without
destroy the newly created debugfs, resulting the debugfs of idt_csr can
never be created later.
The function monitor_card() is a timer handler that runs in an
atomic context, but it calls usleep_range() that can sleep.
As a result, the sleep-in-atomic-context bugs will happen.
The process is shown below:
Add the missing clk_disable_unprepare() before return from
tegra_uart_hw_init() in the error handling path.
When request_irq() fails in tegra_uart_startup(), 'tup->uart_clk'
has been enabled, fix it by adding clk_disable_unprepare().
Fixes: cc9ca4d95846 ("serial: tegra: Only print FIFO error message when an error occurs") Fixes: d781ec21bae6 ("serial: tegra: report clk rate errors") Signed-off-by: Yi Yang <yiyang13@huawei.com> Link: https://lore.kernel.org/r/20221126020852.113378-1-yiyang13@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
UARTBAUD_RDMAE and UARTBAUD_TDMAE are enabled in lpuart32_startup(), but
lpuart32_shutdown() not disable them, only free the dma ring buffer and
release the dma channels, so here disable the Rx/Tx DMA first in
lpuart32_shutdown().
Fixes: 42b68768e51b ("serial: fsl_lpuart: DMA support for 32-bit variant") Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20221125101953.18753-3-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
switchtec_dev_read() didn't handle copy_to_user() errors correctly: it
assigned "rc = -EFAULT", but actually returned either "size", -ENXIO, or
-EBADMSG instead.
Update the failure cases to unlock mrpc_mutex and return -EFAULT directly.
The sysfs link name "virtfn%u" constructed by pci_iov_sysfs_link() requires
17 bytes to contain the longest possible string. Increase VIRTFN_ID_LEN to
accommodate that.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
[bhelgaas: commit log, comment at #define] Fixes: dd7cc44d0bce ("PCI: add SR-IOV API for Physical Function driver") Link: https://lore.kernel.org/r/20221218033347.23743-1-gremlin@altlinux.org Signed-off-by: Alexey V. Vissarionov <gremlin@altlinux.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When acpi_dev_get_memory_resources() fails, the reference count is
left bumped. Drop it as it's done in the other error paths.
Fixes: 43d596e32276 ("usb: typec: intel_pmc_mux: Check the port status before connect") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20230102202933.15968-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Wrapper function that finds all memory type resources by
using acpi_dev_get_resources(). It removes the need for the
drivers to check the resource data type separately.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: c3194949ae8f ("usb: typec: intel_pmc_mux: Don't leak the ACPI device reference count") Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 6746eae4bbad ("coresight: cti: Fix hang in cti_disable_hw()")
PM runtime calls are removed from cti_enable_hw/cti_disable_hw. When
enabling CTI by writing enable sysfs node, clock for accessing CTI
register won't be enabled. Device will crash due to register access
issue. Add PM runtime call in enable_store to fix this issue.
Fixes: 6746eae4bbad ("coresight: cti: Fix hang in cti_disable_hw()") Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com>
[Change to only call pm_runtime_put if a disable happened] Tested-by: Jinlong Mao <quic_jinlmao@quicinc.com> Signed-off-by: James Clark <james.clark@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20230110110736.2709917-3-james.clark@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Writing 0 to the enable control repeatedly results in a negative value
for enable_req_count. After this, writing 1 to the enable control
appears to not work until the count returns to positive.
Change it so that it's impossible for enable_req_count to be < 0.
Return an error to indicate that the disable request was invalid.
Fixes: 835d722ba10a ("coresight: cti: Initial CoreSight CTI Driver") Tested-by: Jinlong Mao <quic_jinlmao@quicinc.com> Signed-off-by: James Clark <james.clark@arm.com> Reviewed-by: Mike Leach <mike.leach@linaro.org> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20230110110736.2709917-2-james.clark@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Check for inactive controls in uvc_ctrl_is_accessible().
Use the new value for the master_id controls if present, otherwise
use the existing value to determine if it is OK to set the control.
Doing this here avoids attempting to set an inactive control, which
will return an error from the USB device, which returns an invalid
errorcode.
This fixes:
warn: v4l2-test-controls.cpp(483): s_ctrl returned EIO
warn: v4l2-test-controls.cpp(483): s_ctrl returned EIO
test VIDIOC_G/S_CTRL: OK
warn: v4l2-test-controls.cpp(739): s_ext_ctrls returned EIO
warn: v4l2-test-controls.cpp(739): s_ext_ctrls returned EIO
warn: v4l2-test-controls.cpp(816): s_ext_ctrls returned EIO
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
We can figure out if reading/writing a set of controls can fail without
accessing them by checking their flags.
This way we can honor the API closer:
If an error is found when validating the list of controls passed with
VIDIOC_G_EXT_CTRLS, then error_idx shall be set to ctrls->count to
indicate to userspace that no actual hardware was touched.
Fixes v4l2-compliance:
Control ioctls (Input 0):
warn: v4l2-test-controls.cpp(765): g_ext_ctrls(0) invalid error_idx 0
fail: v4l2-test-controls.cpp(645): invalid error index write only control
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Ricardo Ribalda <ribalda@chromium.org> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Stable-dep-of: 9f582f0418ed ("media: uvcvideo: Check for INACTIVE in uvc_ctrl_is_accessible()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Create all the class controls for the device defined controls.
Fixes v4l2-compliance:
Control ioctls (Input 0):
fail: v4l2-test-controls.cpp(216): missing control class for class 00980000
fail: v4l2-test-controls.cpp(216): missing control tclass for class 009a0000
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: FAIL
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Ricardo Ribalda <ribalda@chromium.org> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Stable-dep-of: 9f582f0418ed ("media: uvcvideo: Check for INACTIVE in uvc_ctrl_is_accessible()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Just memcmp() with ELFMAG - that's the normal way to do it in userland
code, which that thing is. Besides, that has the benefit of actually
building - str_has_prefix() is *NOT* present in <string.h>.
Fixes: 5f14596e55de "alpha: Replace strncmp with str_has_prefix" Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
In kobject_get_path(), if kobj->name is changed between calls
get_kobj_path_length() and fill_kobj_path() and the length becomes
longer, then fill_kobj_path() will have an out-of-bounds bug.
The actual current problem occurs when the ixgbe probe.
In ixgbe_mii_bus_init(), if the length of netdev->dev.kobj.name
length becomes longer, out-of-bounds will occur.
cpu0 cpu1
ixgbe_probe
register_netdev(netdev)
netdev_register_kobject
device_add
kobject_uevent // Sending ADD events
systemd-udevd // rename netdev
dev_change_name
device_rename
kobject_rename
ixgbe_mii_bus_init |
mdiobus_register |
__mdiobus_register |
device_register |
device_add |
kobject_uevent |
kobject_get_path |
len = get_kobj_path_length // old name |
path = kzalloc(len, gfp_mask); |
kobj->name = name;
/* name length becomes
* longer
*/
fill_kobj_path /* kobj path length is
* longer than path,
* resulting in out of
* bounds when filling path
*/
This is the kasan report:
==================================================================
BUG: KASAN: slab-out-of-bounds in fill_kobj_path+0x50/0xc0
Write of size 7 at addr ff1100090573d1fd by task kworker/28:1/673
I got the following null-ptr-deref report while doing fault injection test:
BUG: kernel NULL pointer dereference, address: 0000000000000058
CPU: 2 PID: 278 Comm: 37-i2c-ds2482 Tainted: G B W N 6.1.0-rc3+
RIP: 0010:klist_put+0x2d/0xd0
Call Trace:
<TASK>
klist_remove+0xf1/0x1c0
device_release_driver_internal+0x196/0x210
bus_remove_device+0x1bd/0x240
device_add+0xd3d/0x1100
w1_add_master_device+0x476/0x490 [wire]
ds2482_probe+0x303/0x3e0 [ds2482]
This is how it happened:
w1_alloc_dev()
// The dev->driver is set to w1_master_driver.
memcpy(&dev->dev, device, sizeof(struct device));
device_add()
bus_add_device()
dpm_sysfs_add() // It fails, calls bus_remove_device.
// error path
bus_remove_device()
// The dev->driver is not null, but driver is not bound.
__device_release_driver()
klist_remove(&dev->p->knode_driver) <-- It causes null-ptr-deref.
// normal path
bus_probe_device() // It's not called yet.
device_bind_driver()
If dev->driver is set, in the error path after calling bus_add_device()
in device_add(), bus_remove_device() is called, then the device will be
detached from driver. But device_bind_driver() is not called yet, so it
causes null-ptr-deref while access the 'knode_driver'. To fix this, set
dev->driver to null in the error path before calling bus_remove_device().
Fixes: 57eee3d23e88 ("Driver core: Call device_pm_add() after bus_add_device() in device_add()") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221205034904.2077765-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The command FIFOs in the Cadence IP can be configured during design
up to 32 entries, and the code in cadence_master.c was assuming the
full 32-entry FIFO. But all current Intel implementations use an 8-entry
FIFO.
Up to now the longest message used was 6 entries so this wasn't
causing any problem. But future Cirrus Logic codecs have downloadable
firmware or tuning blobs. It is more efficient for the codec driver to
issue long transfers that can take advantage of any queuing in the
Soundwire controller and avoid the overhead of repeatedly writing the
page registers.
Make i2c_dw_clk_rate() to return u32 instead of unsigned long, as the
function return the value of get_clk_rate_khz() which returns u32.
Fixes: b33af11de236 ("i2c: designware: Do not require clock when SSCN and FFCN are provided") Signed-off-by: Hanna Hawa <hhhawa@amazon.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When request_irq(ires1->start) failed in w5300_hw_probe(), irq
ires->start has not been freed, and on the clean_up3 error path,
we also need to free ires1->start irq, fix it.
In addition, We should add free_irq in fusb300_remove(), and give
the lables a proper name so that they can be understood easily,
so add free_irq in fusb300_remove(), and update clean_up3 to
err_alloc_request.
Instead of hardcoding IRQ trigger type to IRQF_TRIGGER_RAISING,
let's respect the settings specified in the firmware description.
To be compatible with the older firmware descriptions, if trigger
type is not set up there, we'll set it to default (raising edge).
Fixes: 388be4883952 ("staging:iio: tsl2563 abi fixes and interrupt handling") Fixes: bdab1001738f ("staging:iio:light:tsl2563 remove old style event registration.") Signed-off-by: Ferry Toth <ftoth@exalondelft.nl> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20221207190348.9347-1-andriy.shevchenko@linux.intel.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The HiSilicon DMA Engine is only present on HiSilicon SoCs. Hence add a
dependency on ARCH_HISI, to prevent asking the user about this driver
when configuring a kernel without HiSilicon SoC support.
On DSA/IAX 1.0, TC-A and TC-B in GRPCFG are set as 1 to have best
performance and cannot be changed through sysfs knobs unless override
option is given.
The same values should be set on DSA 2.0 as well.
Fixes: ea7c8f598c32 ("dmaengine: idxd: restore traffic class defaults after wq reset") Fixes: ade8a86b512c ("dmaengine: idxd: Set defaults for GRPCFG traffic class") Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/20221209172141.562648-1-fenghua.yu@intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
`req` is allocated in pcf50633_adc_async_read(), but
adc_enqueue_request() could fail to insert the `req` into queue.
We need to check the return value and free it in the case of failure.
The cs5535-mfd driver uses CPU-specific data that is not available
for ARCH=um builds, so don't allow it to be built for UML.
Prevents these build errors:
In file included from ../arch/x86/include/asm/olpc.h:7,
from ../drivers/mfd/cs5535-mfd.c:17:
../arch/x86/include/asm/geode.h: In function ‘is_geode_gx’:
../arch/x86/include/asm/geode.h:16:31: error: ‘struct cpuinfo_um’ has no member named ‘x86_vendor’
16 | return ((boot_cpu_data.x86_vendor == X86_VENDOR_NSC) &&
../arch/x86/include/asm/geode.h:16:46: error: ‘X86_VENDOR_NSC’ undeclared (first use in this function); did you mean ‘X86_VENDOR_ANY’?
16 | return ((boot_cpu_data.x86_vendor == X86_VENDOR_NSC) &&
../arch/x86/include/asm/geode.h:17:31: error: ‘struct cpuinfo_um’ has no member named ‘x86’
17 | (boot_cpu_data.x86 == 5) &&
../arch/x86/include/asm/geode.h:18:31: error: ‘struct cpuinfo_um’ has no member named ‘x86_model’
18 | (boot_cpu_data.x86_model == 5));
../arch/x86/include/asm/geode.h: In function ‘is_geode_lx’:
../arch/x86/include/asm/geode.h:23:31: error: ‘struct cpuinfo_um’ has no member named ‘x86_vendor’
23 | return ((boot_cpu_data.x86_vendor == X86_VENDOR_AMD) &&
../arch/x86/include/asm/geode.h:23:46: error: ‘X86_VENDOR_AMD’ undeclared (first use in this function); did you mean ‘X86_VENDOR_ANY’?
23 | return ((boot_cpu_data.x86_vendor == X86_VENDOR_AMD) &&
../arch/x86/include/asm/geode.h:24:31: error: ‘struct cpuinfo_um’ has no member named ‘x86’
24 | (boot_cpu_data.x86 == 5) &&
../arch/x86/include/asm/geode.h:25:31: error: ‘struct cpuinfo_um’ has no member named ‘x86_model’
25 | (boot_cpu_data.x86_model == 10));
Fixes: 68f5d3f3b654 ("um: add PCI over virtio emulation driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20221201012541.11809-1-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
A lot of the tsan helpers are already excempt from the UACCESS warnings,
but some more functions were added that need the same thing:
kernel/kcsan/core.o: warning: objtool: __tsan_volatile_read16+0x0: call to __tsan_unaligned_read16() with UACCESS enabled
kernel/kcsan/core.o: warning: objtool: __tsan_volatile_write16+0x0: call to __tsan_unaligned_write16() with UACCESS enabled
vmlinux.o: warning: objtool: __tsan_unaligned_volatile_read16+0x4: call to __tsan_unaligned_read16() with UACCESS enabled
vmlinux.o: warning: objtool: __tsan_unaligned_volatile_write16+0x4: call to __tsan_unaligned_write16() with UACCESS enabled
As Marco points out, these functions don't even call each other
explicitly but instead gcc (but not clang) notices the functions
being identical and turns one symbol into a direct branch to the
other.
Link: https://lkml.kernel.org/r/20230215130058.3836177-4-arnd@kernel.org Fixes: 75d75b7a4d54 ("kcsan: Support distinguishing volatile accesses") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Josh Poimboeuf <jpoimboe@kernel.org> Cc: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com> Cc: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit a1d6cd88c897 ("selftests/ftrace: event_triggers: wait
longer for test_event_enable") introduced bash specific "=="
comparation operator, that test will fail when we run it on a
posix-shell. `checkbashisms` warned it as below.
possible bashism in ftrace/func_event_triggers.tc line 45 (should be 'b = a'):
if [ "$e" == $val ]; then
When doing randconfig builds for sparc32 with COMPILE_TEST, some
(non-Sparc) drivers cause kconfig warnings with the Kconfig symbols PM,
PM_GENERIC_DOMAINS, or PM_GENERIC_DOMAINS_OF.
This is due to arch/sparc/Kconfig not using the PM Kconfig for
Sparc32:
if SPARC64
source "kernel/power/Kconfig"
endif
Arnd suggested adding "|| COMPILE_TEST" to the conditional,
instead of trying to track down every driver that selects
any of these PM symbols.
Fixes the following kconfig warnings:
WARNING: unmet direct dependencies detected for PM
Depends on [n]: SPARC64 [=n]
Selected by [y]:
- SUN20I_PPU [=y] && (ARCH_SUNXI || COMPILE_TEST [=y])
WARNING: unmet direct dependencies detected for PM
Depends on [n]: SPARC64 [=n]
Selected by [y]:
- SUN20I_PPU [=y] && (ARCH_SUNXI || COMPILE_TEST [=y])
On aarch64 CPU related events are not under event_source/devices/cpu/events,
they're under event_source/devices/armv8_pmuv3_0/events on my machine.
Using current auto-complete script will generate below error:
[root@localhost bin]# perf stat -e
ls: cannot access '/sys/bus/event_source/devices/cpu/events': No such file or directory
Fix this by not testing /sys/bus/event_source/devices/cpu/events on
aarch64 machine.
Fixes: 74cd5815d9af6e6c ("perf tool: Improve bash command line auto-complete for multiple events with comma") Reviewed-by: James Clark <james.clark@arm.com> Signed-off-by: Yicong Yang <yangyicong@hisilicon.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: linux-arm-kernel@lists.infradead.org Cc: linuxarm@huawei.com Cc: prime.zeng@hisilicon.com Link: https://lore.kernel.org/r/20230207035057.43394-1-yangyicong@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When it processes AUXTRACE_INFO, it calls to auxtrace_queue_data() to
collect AUXTRACE data first. That won't work with pipe since it needs
lseek() to read the scattered aux data.
$ perf record -o- -e intel_pt// true | perf report -i- --itrace=i100
# To display the perf.data header info, please use --header/--header-only options.
#
0x4118 [0xa0]: failed to process type: 70
Error:
failed to process sample
For the pipe mode, it can handle the aux data as it gets. But there's
no guarantee it can get the aux data in time. So the following warning
will be shown at the beginning:
WARNING: Intel PT with pipe mode is not recommended.
The output cannot relied upon. In particular,
time stamps and the order of events may be incorrect.
Fixes: dbd134322e74f19d ("perf intel-pt: Add support for decoding AUX area samples") Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: James Clark <james.clark@arm.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Leo Yan <leo.yan@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: https://lore.kernel.org/r/20230131023350.1903992-3-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ptwrite is an Intel x86 instruction that writes arbitrary values into an
Intel PT trace. It is not supported on all hardware, so provide an
alternative that makes use of TNT packets to convey the payload data.
TNT packets encode Taken/Not-taken conditional branch information, so
taking branches based on the payload value will encode the value into
the TNT packet. Refer to the changes to the documentation file
perf-intel-pt.txt in this patch for an example.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Link: https://lore.kernel.org/r/20220509152400.376613-2-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: aeb802f872a7 ("perf intel-pt: Do not try to queue auxtrace data on pipe") Signed-off-by: Sasha Levin <sashal@kernel.org>
Add an EXAMPLE section and link to the perf wiki's Intel PT page.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Link: http://lore.kernel.org/lkml/20220426133213.248475-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: aeb802f872a7 ("perf intel-pt: Do not try to queue auxtrace data on pipe") Signed-off-by: Sasha Levin <sashal@kernel.org>
Add documentation for Event Trace and TNT disable to the perf Intel PT man
page.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Link: https://lore.kernel.org/r/20220124084201.2699795-26-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: aeb802f872a7 ("perf intel-pt: Do not try to queue auxtrace data on pipe") Signed-off-by: Sasha Levin <sashal@kernel.org>
In copy_bytes(), it reads the data from the (input) fd and writes it to
the output file. But it does with the read(2) unconditionally which
caused a problem of mixing buffered vs unbuffered I/O together.
You can see the problem when using pipes.
$ perf record -e intel_pt// -o- true | perf inject -b > /dev/null
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.000 MB - ]
0x45c0 [0x30]: failed to process type: 71
It should use perf_data__read() to honor the 'use_stdio' setting.
Fixes: 601366678c93618f ("perf data: Allow to use stdio functions for pipe mode") Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: James Clark <james.clark@arm.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Leo Yan <leo.yan@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: https://lore.kernel.org/r/20230131023350.1903992-2-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
class_find_device_by_of_node() calls class_find_device(), it will take
the reference, use the put_device() to drop the reference when not need
anymore.
The LLVM template is first echo-ed into command_out and then
command_out executed. The echo surrounds the template with double
quotes, however, the template itself may contain quotes. This is
generally innocuous but in tools/perf/tests/bpf-script-test-prologue.c
we see:
...
SEC("func=null_lseek file->f_mode offset orig")
...
where the first double quote ends the double quote of the echo, then
the > redirects output into a file called f_mode.
To avoid this inadvertent behavior substitute redirects and similar
characters to be ASCII control codes, then substitute the output in
the echo back again.
Fixes: 5eab5a7ee032acaa ("perf llvm: Display eBPF compiling command in debug output") Signed-off-by: Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andrii Nakryiko <andrii@kernel.org> Cc: bpf@vger.kernel.org Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: llvm@lists.linux.dev Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Tom Rix <trix@redhat.com> Link: https://lore.kernel.org/r/20230105082609.344538-1-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ->writepage() and ->writepages() operations are supposed to write
entire pages. However, on filesystems with a block size smaller than
PAGE_SIZE, __gfs2_jdata_writepage() only adds the first block to the
current transaction instead of adding the entire page. Fix that.
Fixes: 18ec7d5c3f43 ("[GFS2] Make journaled data files identical to normal files on disk") Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Its possible for __break_lease to find the layout's lease before we've
added the layout to the owner's ls_layouts list. In that case, setting
ls_recalled = true without actually recalling the layout will cause the
server to never send a recall callback.
Move the check for ls_layouts before setting ls_recalled.
Fixes: c5c707f96fc9 ("nfsd: implement pNFS layout recalls") Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Other functions touching shmem->sgt take the pages lock, so do that here
too. drm_gem_shmem_get_pages() & co take the same lock, so move to the
_locked() variants to avoid recursive locking.
Discovered while auditing locking to write the Rust abstractions.
Fixes: 2194a63a818d ("drm: Add library for shmem backed GEM objects") Fixes: 4fa3d66f132b ("drm/shmem: Do dma_unmap_sg before purging pages") Signed-off-by: Asahi Lina <lina@asahilina.net> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230205125124.2260-1-lina@asahilina.net
(cherry picked from commit aa8c85affe3facd3842c8912186623415931cc72) Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
bigben_probe() does not validate that the output report has the
needed report values in the first field.
A malicious device registering a report with one field and a single
value causes an head OOB write in bigben_worker() when
accessing report_field->value[1] to report_field->value[7].
Use hid_validate_values() which takes care of all the needed checks.
Fixes: 256a90ed9e46 ("HID: hid-bigbenff: driver for BigBen Interactive PS3OFMINIPAD gamepad") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Link: https://lore.kernel.org/r/20230211-bigben-oob-v1-1-d2849688594c@diag.uniroma1.it Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use spinlocks to deal with workers introducing a wrapper
bigben_schedule_work(), and several spinlock checks.
Otherwise, bigben_set_led() may schedule bigben->worker after the
structure has been freed, causing a use-after-free.
Fixes: 4eb1b01de5b9 ("HID: hid-bigbenff: fix race condition for scheduled work during removal") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Link: https://lore.kernel.org/r/20230125-hid-unregister-leds-v4-3-7860c5763c38@diag.uniroma1.it Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
bigben_worker() checks report_field to be non-NULL.
The check has been added in commit 918aa1ef104d ("HID: bigbenff: prevent null pointer dereference")
to prevent a NULL pointer crash.
However, the true root cause was a missing check for output
reports, patched in commit c7bf714f8755 ("HID: check empty report_list in bigben_probe()"),
where the type-confused report list_entry was overlapping with
a NULL pointer, which was then causing the crash.
Fixes: 078a85f2806f ("ASoC: dapm: Only power up active channels from a DAI") Signed-off-by: Lucas Tanure <lucas.tanure@collabora.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20230215132851.1626881-1-lucas.tanure@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
wait_for_completion_timeout() never returns a <0 value. It returns either
on timeout or a positive value (at least 1, or number of jiffies left
till timeout)
So, fix the error handling path and return -ETIMEDOUT should a timeout
occur.
When swap is activated to a file on an NFSv4 mount we arrange that the
state manager thread is always present as starting a new thread requires
memory allocations that might block waiting for swap.
Unfortunately the code for allowing the state manager thread to exit when
swap is disabled was not tested properly and does not work.
This can be seen by examining /proc/fs/nfsfs/servers after disabling swap
and unmounting the filesystem. The servers file will still list one
entry. Also a "ps" listing will show the state manager thread is still
present.
There are two problems.
1/ rpc_clnt_swap_deactivate() doesn't walk up the ->cl_parent list to
find the primary client on which the state manager runs.
2/ The thread is not woken up properly and it immediately goes back to
sleep without checking whether it is really needed. Using
nfs4_schedule_state_manager() ensures a proper wake-up.
Reported-by: Olga Kornievskaia <aglo@umich.edu> Fixes: 4dc73c679114 ("NFSv4: keep state manager thread active if swap is enabled") Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we are swapping over NFSv4, we may not be able to allocate memory to
start the state-manager thread at the time when we need it.
So keep it always running when swap is enabled, and just signal it to
start.
This requires updating and testing the cl_swapper count on the root
rpc_clnt after following all ->cl_parent links.
Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: b46d80bd2d6e ("nfs4trace: fix state manager flag printing") Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit acfe0ad74d2e1 ("dm: allocate a special workqueue for deferred
device removal") switched from using system workqueue to a single
workqueue local to DM. But it didn't eliminate the call to
flush_scheduled_work() that was introduced purely for the benefit of
deferred device removal with commit 2c140a246dc ("dm: allow remove to
be deferred").
Since DM core uses its own workqueue (and queue_work) there is no need
to call flush_scheduled_work() from local_exit(). local_exit()'s
destroy_workqueue(deferred_remove_workqueue) handles flushing work
started with queue_work().
Fixes: acfe0ad74d2e1 ("dm: allocate a special workqueue for deferred device removal") Signed-off-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the 'ti,gpio-config' property is not defined, the
device_property_count_u32() will return an error, rather than zero.
The current check, only handles a return value of zero, which assumes that
the property is defined and has nothing defined.
This change extends the check to also check for an error case (most likely
to be hit by the case that the 'ti,gpio-config' is not defined).
In case that the 'ti,gpio-config' and the returned 'gpio_count' is not
correct, there is a 'if (gpio_count != ADCX140_NUM_GPIO_CFGS)' check, a few
lines lower that will return -EINVAL.
This means that someone tried to define 'ti,gpio-config', but with the
wrong number of GPIOs.
Fixes: d5214321498a ("ASoC: tlv320adcx140: Add support for configuring GPIO pin") Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de> Signed-off-by: Alexandru Ardelean <alex@shruggie.ro> Link: https://lore.kernel.org/r/20230213073805.14640-1-alex@shruggie.ro Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently for broken fan driver returns value calculated based on error
code (0xFF) in related fan speed register.
Thus, for such fan user gets fan{n}_fault to 1 and fan{n}_input with
misleading value.
Add check for fan fault prior return speed value and return zero if
fault is detected.
Fixes: 65afb4c8e7e4 ("hwmon: (mlxreg-fan) Add support for Mellanox FAN driver") Signed-off-by: Vadim Pasternak <vadimp@nvidia.com> Link: https://lore.kernel.org/r/20230212145730.24247-1-vadimp@nvidia.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the driver always sets the controller to dual data bit mode
for both tx and rx data in the profile mode control register even for
single data bit transfer. Luckily the opcode is set correctly according
to SPI transfer data bit width so it does not actually cause issues.
This change fixes the problem by setting tx and rx data bit mode field
correctly according to the actual SPI transfer tx and rx data bit width.
For some reason we ended up with incorrect mclk rate which should be 1920000 instead of 96000, So far we were getting lucky as the same clk
is set to 192000 by wsa and va macro. This issue is discovered when there
is no wsa macro active and only rx or tx path is tested.
Fix this by setting correct rate.
Fixes: c39667ddcfc5 ("ASoC: codecs: lpass-tx-macro: add support for lpass tx macro") Fixes: af3d54b99764 ("ASoC: codecs: lpass-rx-macro: add support for lpass rx macro") Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20230209122806.18923-7-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using bulk clocks and referencing them individually using array index is
not great for readers.
So move them to individual clocks handling and also remove some unnecessary
error handling in the code.
Using bulk clocks and referencing them individually using array index is
not great for readers.
So move them to individual clocks handling and also remove some unnecessary
error handling in the code.
In certain circumstances, such as when creating I2C-connected HID
devices, we want to pass and retain some quirks (axis inversion, etc).
The source of such quirks may be device tree, or DMI data, or something
else not readily available to the HID core itself and therefore cannot
be reconstructed easily. To allow this, introduce "initial_quirks" field
in hid_device structure and use it when determining the final set of
quirks.
This fixes the problem with i2c-hid setting up device-tree sourced
quirks too late and losing them on device rebind, and also allows to
sever the tie between hid-code and i2c-hid when applying DMI-based
quirks.
Fixes: b60d3c803d76 ("HID: i2c-hid-of: Expose the touchscreen-inverted properties") Fixes: a2f416bf062a ("HID: multitouch: Add quirks for flipped axes") Reviewed-by: Guenter Roeck <groeck@chromium.org> Tested-by: Allen Ballway <ballway@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Alistair Francis <alistair@alistair23.me> Link: https://lore.kernel.org/r/Y+LYwu3Zs13hdVDy@google.com Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Certain touchscreen devices, such as the ELAN9034, are oriented
incorrectly and report touches on opposite points on the X and Y axes.
For example, a 100x200 screen touched at (10,20) would report (90, 180)
and vice versa.
This is fixed by adding device quirks to transform the touch points
into the correct spaces, from X -> MAX(X) - X, and Y -> MAX(Y) - Y.
Signed-off-by: Allen Ballway <ballway@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Stable-dep-of: 03a86105556e ("HID: retain initial quirks set up when creating HID devices") Signed-off-by: Sasha Levin <sashal@kernel.org>
Add check for dma_map_single() and return error if it fails in order to
avoid invalid DMA address.
Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver") Link: https://lore.kernel.org/r/20230128110832.6792-1-jiasheng@iscas.ac.cn Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Reviewed-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
