Harald Hoyer [Tue, 24 Jun 2014 16:11:47 +0000 (18:11 +0200)]
install: add -H flag for install
inst* functions and dracut-install now accept the "-H" flag, which
logs all installed files to /lib/dracut/hostonly-files. This is used
to remove those files, if rd.hostonly is given on the kernel command line.
Hari Bathini [Mon, 2 Jun 2014 10:57:37 +0000 (16:27 +0530)]
lsinird: Adding option "-m|--mod" to list dracut modules in the image
This patch adds option "-m|--mod" to lsinitrd to list dracut
modules in the image because sometimes having an option to
only list the dracut modules in the image could be handy.
Alex Harpin [Tue, 6 May 2014 22:41:17 +0000 (23:41 +0100)]
bonding: use hwaddr of the slave rather than the master
When a bonded interface is brought up, any slaves included in the bond
have their hardware address set to that of the bond master. Although
this allows an interface to be brought up on start up, when the
configuration file is imported into the booted system it prevents
the bonded interface being successfully restarted.
The fix involves obtaining the hardware address of the slaves before
they are added to the bond and then using this value in the
configuration file.
Peter Robinson [Fri, 23 May 2014 10:54:01 +0000 (11:54 +0100)]
kernel-modules: Fix storage module selection for sdhci/mmc/ahci
Currently the block driver detection for generic initrd doesn't include
the SD/MMC drivers so we fail to boot generic images on any device using
those platforms as boot devices when using a generic initrd. Add logic
to detect those modules. This primarily fixes embedded ARM devices but
also likely intel tablets/dev boards and enterprise hypervisors that
have the ability to boot from SD.
Also the ahci_init_controller misses a number of drivers that use the
libahci_platform module for the init so this fixes some missing achi
moduless too.
Finally it cleans up the ARM storage module hacks that the above now
deals with in a more generic manner.
WANG Chao [Fri, 4 Apr 2014 06:37:42 +0000 (14:37 +0800)]
dracut-pre-pivot pulls in remote-fs.target
It turns out that commit f30b74e (dracut-initqueue service runs before
remote-fs-pre.target) is partial fix for remote fs mounts. Because no
one pulls in remote-fs.target, we can never start remote fs mounts.
Now pull in remote-fs.target in dracut-pre-pivot.
Julian Wolf [Thu, 3 Apr 2014 12:55:19 +0000 (14:55 +0200)]
udev-rules: include 59-scsi-sg3_utils.rules
Without the 59-scsi-sg3_utils.rules udev-rule a couple of devices are missing
in /dev/disk/by-id.
If the luks device is specified by-id in /etc/crypttab and rd.luks.uuid not
passed as a commandline parameter during boot, systemd tries to start its
crypto services which depend on those missing devices until it times out and
exits to dracut rescue shell.
By convention, strstr should be a literal string match. Previously, it
would match as a glob pattern. Some code used that, so add new
functions strglob and strglobin to do what that code expects, and
specify them tightly too. strglob tests whether the glob pattern
matches the entire string (the name strglob is also used in the yorick
language, and that's what it does there), while strglobin tests whether
the glob pattern matches anywhere in the string.
Also tightens str_starts, str_ends, and str_replace to deal with
literal strings only. In a quick grep I did not find code that depended
on these functions matching globs.
Changes the call sites where strstr was used with glob patterns to use
strglobin or strglob as the intention seemed to be (or, in one case,
strstr with the * removed as it did not affect the result anyway).
Harald Hoyer [Thu, 3 Apr 2014 06:54:27 +0000 (08:54 +0200)]
lvm:module-setup.sh: check for existance of 69-dm-lvm-metad.rules
Before modifying 69-dm-lvm-metad.rules, we should check for the
existance first. Otherwise this results in error messages on
distributions (debian), which do not ship these rules.
WANG Chao [Tue, 1 Apr 2014 07:20:49 +0000 (15:20 +0800)]
fstab: do not mount and fsck from fstab if using systemd
If using systemd in initramfs, we could run into a race condition when
dracut and systemd both are trying to mount and run fsck for the same
filesystem, and mount or fsck could be a failure.
To fix such failure, we should use systemd to mount/fsck from /etc/fstab
only.
v2: check $DRACUT_SYSTEMD suggested by Alexander Tsoy
Harald Hoyer [Thu, 27 Mar 2014 08:27:53 +0000 (09:27 +0100)]
lsinitrd.sh: prevent < <$() construct
Running dracut in a chroot environment, which has /dev not correctly
setup will result in errors like:
/usr/bin/lsinitrd: line 164: /dev/fd/62: No such file or directory
cpio: Malformed number �5�OK��
cpio: Malformed number 5�OK��
cpio: Malformed number �OK��
This is because bash wants /dev/fd/<num> for constructs like:
foo < <$(bar)
Dave Young [Thu, 27 Feb 2014 02:44:23 +0000 (10:44 +0800)]
add default values in fstab_lines
It's useful for passing a full fstab line including like fs_passno so fsck
can take effect.
Previously it's assumed that there's no fs_freq and fs_passno in fstab lines
so original code just append "0 0" at the end of each fstab lines.
Improve this issue by assign default value in case they are not passed in.
Three field are handled here:
fs_mntops: default to "defaults"
fs_freq: default to "0"
fs_passno: default to "2"
Colin Guthrie [Wed, 5 Feb 2014 10:06:51 +0000 (10:06 +0000)]
dracut.sh: Fix variable name typo.
This caused the root_dev variable not to be set which in turn meant that
the root device was not whitelisted in 99base/module-setup.sh when injecting
compile-time devexists hooks in hostonly initrds. This ties the generated
initrd to the root fs device (typically the UUID) rather than relying solely
only the root= kernel command line.
While it is hostonly, not hardcoding e.g. UUIDs is still desirable. Any
swap partition on the host device is still added however.