dt-bindings: serial: 8250_omap: Add wakeup pinctrl state
Pins associated with the 8250 omap unit can be the source of a wakeup in
deep sleep states. To be able to wakeup, these pins have to be
configured in a special way. To support this configuration add the
default and wakeup pinctrl states.
Tapio Reijonen [Mon, 8 Sep 2025 06:53:43 +0000 (06:53 +0000)]
serial: max310x: improve interrupt handling
When there is a heavy load of receiving characters to all
four UART's, the warning 'Hardware RX FIFO overrun' is
sometimes detected.
The current implementation always service first the highest UART
until no more interrupt and then service another UART
(ex: UART3 will be serviced for as long as there are interrupts
for it, then UART2, etc).
This commit handle all individual interrupt sources before
reading the global IRQ register again.
This commit has also a nice side-effect of improving the efficiency
of the driver by reducing the number of reads of the global
IRQ register.
Zizhi Wo [Thu, 4 Sep 2025 02:39:55 +0000 (10:39 +0800)]
tty/vt: Add missing return value for VT_RESIZE in vt_ioctl()
In vt_ioctl(), the handler for VT_RESIZE always returns 0, which prevents
users from detecting errors. Add the missing return value so that errors
can be properly reported to users like vt_resizex().
Wang Liang [Thu, 4 Sep 2025 02:33:45 +0000 (10:33 +0800)]
vt: remove redundant check on vc_mode in con_font_set()
Previous commit edab558feba1 ("vt: sort out locking for font handling")
move the vc_mode check into console_lock protect, but forget to remove the
old check in con_font_set(). Just remove the redundant check.
serial: qcom-geni: Add DFS clock mode support to GENI UART driver
GENI UART driver currently supports only non-DFS (Dynamic Frequency
Scaling) mode for source frequency selection. However, to operate correctly
in DFS mode, the GENI SCLK register must be programmed with the appropriate
DFS index. Failing to do so can result in incorrect frequency selection
Add support for Dynamic Frequency Scaling (DFS) mode in the GENI UART
driver by configuring the GENI_CLK_SEL register with the appropriate DFS
index. This ensures correct frequency selection when operating in DFS mode.
Replace the UART driver-specific logic for clock selection with the GENI
common driver function to obtain the desired frequency and corresponding
clock index. This improves maintainability and consistency across
GENI-based drivers.
The only user -- 8250_hp300 -- tests for CONFIG_HPDCA and CONFIG_HPAPCI.
It does not test for *_MODULE variants. That means that if someone sets
the configs to =m, the code is not compiled at all.
There is actually no point having these as tristate. Switch them to
bool.
Seppo Takalo [Wed, 27 Aug 2025 12:26:56 +0000 (15:26 +0300)]
tty: n_gsm: Don't block input queue by waiting MSC
Currently gsm_queue() processes incoming frames and when opening
a DLC channel it calls gsm_dlci_open() which calls gsm_modem_update().
If basic mode is used it calls gsm_modem_upd_via_msc() and it
cannot block the input queue by waiting the response to come
into the same input queue.
Instead allow sending Modem Status Command without waiting for remote
end to respond. Define a new function gsm_modem_send_initial_msc()
for this purpose. As MSC is only valid for basic encoding, it does
not do anything for advanced or when convergence layer type 2 is used.
Zong Jiang [Wed, 27 Aug 2025 12:03:19 +0000 (20:03 +0800)]
serial: qcom-geni: Fix off-by-one error in ida_alloc_range()
The ida_alloc_range() function expects an inclusive range, meaning both
the start and end values are valid allocation targets. Passing nr_ports
as the upper bound allows allocation of an ID equal to nr_ports, which
is out of bounds when used as an index into the port array.
Fix this by subtracting 1 from nr_ports in both calls to ida_alloc_range(),
ensuring the allocated ID stays within the valid range
[start, nr_ports - 1].
This prevents potential out-of-bounds access when the allocated ID is used
as an index.
Fixes: 9391ab1ed9b3 ("serial: qcom-geni: Make UART port count configurable via Kconfig") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/r/202508180815.R2nDyajs-lkp@intel.com/ Signed-off-by: Zong Jiang <quic_zongjian@quicinc.com> Link: https://lore.kernel.org/r/20250827120319.1682835-1-quic_zongjian@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Claudiu Beznea [Wed, 27 Aug 2025 10:17:47 +0000 (13:17 +0300)]
serdev: Drop dev_pm_domain_detach() call
Starting with commit f99508074e78 ("PM: domains: Detach on
device_unbind_cleanup()"), there is no longer a need to call
dev_pm_domain_detach() in the bus remove function. The
device_unbind_cleanup() function now handles this to avoid
invoking devres cleanup handlers while the PM domain is
powered off, which could otherwise lead to failures as
described in the above-mentioned commit.
Drop the explicit dev_pm_domain_detach() call and rely instead
on the flags passed to dev_pm_domain_attach() to power off the
domain.
Calixte Pernot [Mon, 25 Aug 2025 12:56:09 +0000 (14:56 +0200)]
vt: add support for smput/rmput escape codes
Support "\e[?1049h" and "\e[?1049l" escape codes.
This patch allows programs to enter and leave alternate screens.
This feature is widely available in graphical terminal emulators and mostly
used by fullscreen terminal-based user interfaces such as text editors.
Most editors such as vim and nano assume this escape code in not supported
and will not try to print the escape sequence if TERM=linux.
To try out this patch, run `TERM=xterm-256color vim` inside a VT.
Xichao Zhao [Tue, 19 Aug 2025 12:09:27 +0000 (20:09 +0800)]
tty: serial: Modify the use of dev_err_probe()
The dev_err_probe() doesn't do anything when error is '-ENOMEM'.
Make the following two changes:
(1) Replace -ENOMEM with -ENOSPC in max3100_probe().
(2) Just return -ENOMEM instead in max310x_probe().
Having the new tty_port_tty guard, use it in tty3270_resize(). This
makes the code easier to read. The winsize is now defined in the
scope and initialized immediately, so that it's obvious.
Having all the new guards, use them in the vt code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
A local free_page_ptr __free guard is introduced for
__get_free_page/free_page (with proper casts). This could be made public
in include/. But I am not sure if there are more possible users, so
keeping completely private here.
tty/vt: use guard()s in con_font_set/get() and con_{set,get}_unimap()
Having all the new guards, use them in the 8250_rsa code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
The new __free()-annotated declarations are moved to the allocation points
as is preferred:
https://lore.kernel.org/all/CAHk-=wjvh_LUpa=864joG2JJXs3+viO-kLzLidR2JLyMr4MNwA@mail.gmail.com/
Except font_data in con_font_get(). The scope in there would not match
the expected lifetime. But the declaration is moved closer.
Having all the new guards, use them in the 8250_rsa code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
Having all the new guards, use them in the 8250_omap code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
For this to work, UART_CAP_RPM has to be set to up->capabilities a bit
earlier.
To use guard()s easily in omap_8250_set_termios(), split it into atomic
and non-atomic part. The former can be easily guarded -- without a need
of indenting or moving code.
omap_8250_set_termios() would likely profit from a cleanup similar to
one in serial8250_do_set_termios() in commit cdc4a3e0b235 ("serial:
8250: extract serial8250_set_fcr()") and earlier.
serial: 8250_core: use guard() in serial_unlink_irq_chain()
Having all the new guards, use them in the 8250 code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
serial_unlink_irq_chain() is done separately here because with the
guard() used, those BUG_ON()s can be switched WARN_ON()s as we can
actually handle the conditions and return (despite something went really
wrong).
Having all the new guards, use them in the 8250 code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
Having all the new guards, use them in the serial_core code. This
improves readability, makes error handling easier, and marks locked
portions of code explicit.
Having all the new guards, use them in the mxser code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
mxser: use tty_port_tty guard() in mxser_port_isr()
Use scoped_guard() and reorder the function. This is done separately
from the other changes, as it is slighly more intrusive: scoped_guard()
handles the have-tty case and returns. The non-tty case is done at the
end of the function.
Having all the new guards, use them in the tty_port code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
Having this, guards like these work:
scoped_guard(tty_port_tty, port)
tty_wakeup(scoped_tty());
See e.g. "tty_port: use scoped_guard()" later in this series.
The definitions depend on CONFIG_TTY. It's due to tty_kref_put().
On !CONFIG_TTY, it is an inline and its declaration would conflict. The
guards are not needed in that case, of course.
Zong Jiang [Tue, 12 Aug 2025 05:48:19 +0000 (13:48 +0800)]
serial: qcom-geni: Make UART port count configurable via Kconfig
Replace the hardcoded GENI_UART_PORTS macro with a new Kconfig option
SERIAL_QCOM_GENI_UART_PORTS to allow platforms to configure the maximum
number of UART ports supported by the driver at build time.
This improves flexibility for platforms that require more than the
previously fixed number of UART ports, and avoids unnecessary allocation
for unused ports.
Replace the static allocation of UART ports with dynamic allocation
using devm_kzalloc. This change removes the fixed-size array and instead
allocates each UART port structure on demand during probe, improving
memory efficiency and scalability.
Brian Masney [Sun, 10 Aug 2025 22:14:25 +0000 (18:14 -0400)]
tty: serial: mvebu-uart: convert from round_rate() to determine_rate()
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
appended to the "under-the-cut" portion of the patch.
Abinash Singh [Wed, 6 Aug 2025 21:51:34 +0000 (03:21 +0530)]
serial: 8250_platform: Reduce stack usage in serial8250_probe_platform()
The function serial8250_probe_platform() in 8250_platform.c triggered a
frame size warning:
drivers/tty/serial/8250/8250_platform.c: In function ‘serial8250_probe_platform.isra’:
drivers/tty/serial/8250/8250_platform.c:201:1: warning: the frame size of 1184 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This patch reduces the stack usage by dynamically allocating the
`uart` structure using kzalloc(), rather than placing it on
the stack. This eliminates the overflow warning and improves kernel
robustness.
Abinash Singh [Wed, 6 Aug 2025 21:51:33 +0000 (03:21 +0530)]
serial: 8250_platform: Reduce stack usage in serial8250_probe_acpi()
The function serial8250_probe_acpi() in 8250_platform.c triggered a
frame size warning:
drivers/tty/serial/8250/8250_platform.c: In function ‘serial8250_probe_acpi’:
drivers/tty/serial/8250/8250_platform.c:152:1: warning: the frame size of 1160 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This patch reduces the stack usage by dynamically allocating the
`uart` structure using kzalloc(), rather than placing it on
the stack. This eliminates the overflow warning and improves kernel
robustness.
tty: serial: ip22zilog: Use platform device for probing
After commit 84a9582fd203 ("serial: core: Start managing serial controllers
to enable runtime PM") serial drivers need to provide a device in
struct uart_port.dev otherwise an oops happens. To fix this issue
for ip22zilog driver switch driver to a platform driver and setup
the serial device in sgi-ip22 code.
Linus Torvalds [Sun, 10 Aug 2025 05:51:37 +0000 (08:51 +0300)]
Merge tag 'smp_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smp fixes from Borislav Petkov:
- Remove an obsolete comment and fix spelling
* tag 'smp_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu: Remove obsolete comment from takedown_cpu()
smp: Fix spelling in on_each_cpu_cond_mask()'s doc-comment
Linus Torvalds [Sun, 10 Aug 2025 05:46:47 +0000 (08:46 +0300)]
Merge tag 'irq_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Fix a wrong ioremap size in mvebu-gicp
- Remove yet another compile-test case for a driver which needs an
additional dependency
- Fix a lock inversion scenario in the IRQ unit test suite
- Remove an impossible flag situation in gic-v5
- Do not iounmap resources in gic-v5 which are managed by devm
- Make sure stale, left-over interrupts in mvebu-gicp are cleared on
driver init
- Fix a reference counting mishap in msi-lib
- Fix a dereference-before-null-ptr-check case in the riscv-imsic
irqchip driver
* tag 'irq_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mvebu-gicp: Use resource_size() for ioremap()
irqchip: Build IMX_MU_MSI only on ARM
genirq/test: Resolve irq lock inversion warnings
irqchip/gic-v5: Remove IRQD_RESEND_WHEN_IN_PROGRESS for ITS IRQs
irqchip/gic-v5: iwb: Fix iounmap probe failure path
irqchip/mvebu-gicp: Clear pending interrupts on init
irqchip/msi-lib: Fix fwnode refcount in msi_lib_irq_domain_select()
irqchip/riscv-imsic: Don't dereference before NULL pointer check
Linus Torvalds [Sun, 10 Aug 2025 05:15:32 +0000 (08:15 +0300)]
Merge tag 'x86_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Fix an interrupt vector setup race which leads to a non-functioning
device
- Add new Intel CPU models *and* a family: 0x12. Finally. Yippie! :-)
* tag 'x86_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Plug vector setup race
x86/cpu: Add new Intel CPU model numbers for Wildcatlake and Novalake
Len Brown [Sun, 10 Aug 2025 01:08:26 +0000 (21:08 -0400)]
tools/power turbostat: version 2025.09.09
Probe and display L3 Cache topology
Add ability to average an added counter
(useful for pre-integrated "counters", such as Watts)
Break the limit of 64 built-in counters.
Assorted bug fixes and minor feature tweaks
/sys/devices/system/cpu/intel_uncore_frequency/package_X_die_Y/
may be readable by all, but
/sys/devices/system/cpu/intel_uncore_frequency/package_X_die_Y/current_freq_khz
may be readable only by root.
Non-root turbostat users see complaints in this scenario.
Fail probe of the interface if we can't read current_freq_khz.
Reported-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Original-patch-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Wed, 11 Jun 2025 06:50:26 +0000 (14:50 +0800)]
tools/power turbostat: Fix DMR support
Together with the RAPL MSRs, there are more MSRs gone on DMR, including
PLR (Perf Limit Reasons), and IRTL (Package cstate Interrupt Response
Time Limit) MSRs. The configurable TDP info should also be retrieved
from TPMI based Intel Speed Select Technology feature.
Remove the access of these MSRs for DMR. Improve the DMR platform
feature table to make it more readable at the same time.
Fixes: 83075bd59de2 ("tools/power turbostat: Add initial support for DMR") Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
tools/power turbostat: add format "average" for external attributes
External atributes with format "raw" are not printed in summary lines
for nodes/packages (or with option -S). The new format "average"
behaves like "raw" but also adds the summary data
Signed-off-by: Michael Hebenstreit <michael.hebenstreit@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Sat, 12 Jul 2025 20:16:56 +0000 (16:16 -0400)]
tools/power turbostat: Support more than 64 built-in-counters
We have out-grown the ability to use a 64-bit memory location
to inventory every possible built-in counter.
Leverage the the CPU_SET(3) macros to break this barrier.
Also, break the Joules & Watts counters into two,
since we can no longer 'or' them together...
Linus Torvalds [Sat, 9 Aug 2025 15:12:23 +0000 (18:12 +0300)]
Merge tag 'tty-6.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fix from Greg KH:
"Here is a single revert of one of the previous patches that went in
the last tty/serial merge that is breaking userspace on some platforms
(specifically powerpc, probably a few others.)
It accidentially changed the ioctl values of some tty ioctls, which
breaks xorg.
The revert has been in linux-next all this week with no reported
issues"
* tag 'tty-6.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "tty: vt: use _IO() to define ioctl numbers"
Linus Torvalds [Sat, 9 Aug 2025 05:47:28 +0000 (08:47 +0300)]
Merge tag 'block-6.17-20250808' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- MD pull request via Yu:
- mddev null-ptr-dereference fix, by Erkun
- md-cluster fail to remove the faulty disk regression fix, by
Heming
- minor cleanup, by Li Nan and Jinchao
- mdadm lifetime regression fix reported by syzkaller, by Yu Kuai
- MD pull request via Christoph
- add support for getting the FDP featuee in fabrics passthru path
(Nitesh Shetty)
- add capability to connect to an administrative controller
(Kamaljit Singh)
- fix a leak on sgl setup error (Keith Busch)
- initialize discovery subsys after debugfs is initialized
(Mohamed Khalfella)
- fix various comment typos (Bjorn Helgaas)
- remove unneeded semicolons (Jiapeng Chong)
- nvmet debugfs ordering issue fix
- Fix UAF in the tag_set in zloop
- Ensure sbitmap shallow depth covers entire set
- Reduce lock roundtrips in io context lookup
- Move scheduler tags alloc/free out of elevator and freeze lock, to
fix some lockdep found issues
- Improve robustness of queue limits checking
- Fix a regression with IO priorities, if no io context exists
* tag 'block-6.17-20250808' of git://git.kernel.dk/linux: (26 commits)
lib/sbitmap: make sbitmap_get_shallow() internal
lib/sbitmap: convert shallow_depth from one word to the whole sbitmap
nvmet: exit debugfs after discovery subsystem exits
block, bfq: Reorder struct bfq_iocq_bfqq_data
md: make rdev_addable usable for rcu mode
md/raid1: remove struct pool_info and related code
md/raid1: change r1conf->r1bio_pool to a pointer type
block: ensure discard_granularity is zero when discard is not supported
zloop: fix KASAN use-after-free of tag set
block: Fix default IO priority if there is no IO context
nvme: fix various comment typos
nvme-auth: remove unneeded semicolon
nvme-pci: fix leak on sgl setup error
nvmet: initialize discovery subsys after debugfs is initialized
nvme: add capability to connect to an administrative controller
nvmet: add support for FDP in fabrics passthru path
md: rename recovery_cp to resync_offset
md/md-cluster: handle REMOVE message earlier
md: fix create on open mddev lifetime regression
block: fix potential deadlock while running nr_hw_queue update
...
Linus Torvalds [Sat, 9 Aug 2025 05:45:08 +0000 (08:45 +0300)]
Merge tag 'io_uring-6.17-20250808' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
- Allow vectorized payloads for send/send-zc - like sendmsg, but
without the hassle of a msghdr.
- Fix for an integer wrap that should go to stable, spotted by syzbot.
Nothing alarming here, as you need to be root to hit this.
Nevertheless, it should get fixed.
FWIW, kudos to the syzbot crew for having much nicer reproducers now,
and with nicely annotated source code as well. This is particularly
useful as syzbot uses the raw interface rather than liburing,
historically it's been difficult to turn a syzbot reproducer into a
meaningful test case. With the recent changes, not true anymore!
* tag 'io_uring-6.17-20250808' of git://git.kernel.dk/linux:
io_uring/memmap: cast nr_pages to size_t before shifting
io_uring/net: Allow to do vectorized send
Linus Torvalds [Sat, 9 Aug 2025 05:43:24 +0000 (08:43 +0300)]
Merge tag 'spi-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"There's one fix here for an issue with the CS42L43 where we were
allocating a single property for client devices as just that property
rather than a terminated array of properties like we are supposed to.
We also have an update to the MAINTAINERS file for some Renesas
devices"
* tag 'spi-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: cs42l43: Property entry should be a null-terminated array
MAINTAINERS: Add entries for the RZ/V2H(P) RSPI
Linus Torvalds [Sat, 9 Aug 2025 05:41:53 +0000 (08:41 +0300)]
Merge tag 'regulator-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"This fixes an issue with the newly added code for handling large
voltage changes on regulators which require that individual voltage
changes cover a limited range, the check for convergence was broken"
* tag 'regulator-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: correct convergence check in regulator_set_voltage()
Linus Torvalds [Sat, 9 Aug 2025 05:40:28 +0000 (08:40 +0300)]
Merge tag 'regmap-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"These patches fix a lockdep issue Russell King reported with nested
regmap-irqs (unusual since regmap is generally for devices on slow
buses so devices don't get nested), plus add a missing mutex free
which I noticed while implementing a fix for that issue"
* tag 'regmap-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: irq: Avoid lockdep warnings with nested regmap-irq chips
regmap: irq: Free the regmap-irq mutex
Linus Torvalds [Sat, 9 Aug 2025 05:37:17 +0000 (08:37 +0300)]
Merge tag 'mailbox-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox
Pull mailbox updates from Jassi Brar:
- aspeed: add driver and bindings for ast2700
- broadcom: add driver and bindings for bcm74110
- mediatek: fix RPM api usage
- qcom: use dev_fwnode
- pcc: support shared buffer
- misc dt-bindings cleanup
* tag 'mailbox-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox:
mailbox/pcc: support mailbox management of the shared buffer
mailbox: bcm74110: Fix spelling mistake
mailbox: bcm74110: remove unneeded semicolon
mailbox: aspeed: add mailbox driver for AST27XX series SoC
dt-bindings: mailbox: Add ASPEED AST2700 series SoC
dt-bindings: mailbox: Drop consumers example DTS
dt-bindings: mailbox: nvidia,tegra186-hsp: Use generic node name
dt-bindings: mailbox: Correct example indentation
dt-bindings: mailbox: ti,secure-proxy: Add missing reg maxItems
dt-bindings: mailbox: amlogic,meson-gxbb-mhu: Add missing interrupts maxItems
dt-bindings: mailbox: qcom-ipcc: document the Milos Inter-Processor Communication Controller
mailbox: Add support for bcm74110
dt-bindings: mailbox: Add support for bcm74110
mailbox: Use dev_fwnode()
mailbox: mtk-cmdq: Switch to pm_runtime_put_autosuspend()
Linus Torvalds [Sat, 9 Aug 2025 05:15:43 +0000 (08:15 +0300)]
Merge tag 'gpio-updates-for-v6.17-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"As discussed: there's a small commit that removes the legacy GPIO line
value setter callbacks as they're no longer used and a big, treewide
commit that renames the new ones to the old names across all GPIO
drivers at once.
While at it: there are also two fixes that I picked up over the course
of the merge window:
- remove unused, legacy GPIO line value setters from struct gpio_chip
- rename the new set callbacks back to the original names treewide
- fix interrupt handling in gpio-mlxbf2
- revert a buggy immutable irqchip conversion"
* tag 'gpio-updates-for-v6.17-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
treewide: rename GPIO set callbacks back to their original names
gpio: remove legacy GPIO line value setter callbacks
gpio: mlxbf2: use platform_get_irq_optional()
Revert "gpio: pxa: Make irq_chip immutable"
Linus Torvalds [Sat, 9 Aug 2025 05:12:41 +0000 (08:12 +0300)]
Merge tag 'sound-fix-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- Support for ASoC AMD ACP 7.2 with new IDs
- ASoC Intel AVS and SOF fixes
- Yet more kconfig adjustments for HD-audio codecs
- TAS2781 codec fixes
- Fixes for longstanding (rather minor) bugs in Intel LPE audio and
USB-audio drivers
* tag 'sound-fix-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/cirrus: Restrict prompt only for CONFIG_EXPERT
ALSA: hda/hdmi: Restrict prompt only for CONFIG_EXPERT
ALSA: hda/realtek: Restrict prompt only for CONFIG_EXPERT
ALSA: hda/ca0132: Fix missing error handling in ca0132_alt_select_out()
ASoC: SOF: Intel: hda-sdw-bpt: fix SND_SOF_SOF_HDA_SDW_BPT dependencies
ALSA: hda/tas2781: Support L"SmartAmpCalibrationData" to save calibrated data
ALSA: intel_hdmi: Fix off-by-one error in __hdmi_lpe_audio_probe()
ALSA: hda/realtek: add LG gram 16Z90R-A to alc269 fixup table
ALSA: usb-audio: Don't use printk_ratelimit for debug prints
ASoC: Intel: sof_sdw: Add quirk for Alienware Area 51 (2025) 0CCC SKU
ASoC: tas2781: Fix the wrong step for TLV on tas2781
ASoC: amd: acp: Add SoundWire SOF machine driver support for acp7.2 platform
ASoC: amd: acp: Add SoundWire legacy machine driver support for acp7.2 platform
ASoC: amd: ps: Add SoundWire pci and dma driver support for acp7.2 platform
ASoC: SOF: amd: Add sof audio support for acp7.2 platform
ASoC: Intel: avs: Fix uninitialized pointer error in probe()
ASoC: wm8962: Clear master mode when enter runtime suspend
ASoC: SOF: amd: acp-loader: Use GFP_KERNEL for DMA allocations in resume context
Linus Torvalds [Sat, 9 Aug 2025 04:58:55 +0000 (07:58 +0300)]
Merge tag 'soc-fixes-6.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"These are a few patches to fix up bits that went missing during the
merge window: The tegra and s3c patches address trivial regressions
from conflicts, the bcm7445 makes the dt conform to the binding that
was made stricter"
* tag 'soc-fixes-6.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: tegra: Remove numa-node-id properties
ARM: s3c/gpio: complete the conversion to new GPIO value setters
ARM: dts: broadcom: Fix bcm7445 memory controller compatible
Linus Torvalds [Sat, 9 Aug 2025 04:35:03 +0000 (07:35 +0300)]
Merge tag 'xtensa-20250808' of https://github.com/jcmvbkbc/linux-xtensa
Pull xtensa update from Max Filippov:
- replace __ASSEMBLY__ with __ASSEMBLER__ in arch headers
* tag 'xtensa-20250808' of https://github.com/jcmvbkbc/linux-xtensa:
xtensa: Replace __ASSEMBLY__ with __ASSEMBLER__ in non-uapi headers
xtensa: Replace __ASSEMBLY__ with __ASSEMBLER__ in uapi headers
Linus Torvalds [Sat, 9 Aug 2025 04:26:19 +0000 (07:26 +0300)]
Merge tag 'v6.17-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"Fix a regression that broke hmac(sha3-224-s390)"
* tag 'v6.17-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: hash - Increase HASH_MAX_DESCSIZE for hmac(sha3-224-s390)
Linus Torvalds [Sat, 9 Aug 2025 04:20:44 +0000 (07:20 +0300)]
Merge tag 'nfs-for-6.17-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Stable fixes:
- don't inherit NFS filesystem capabilities when crossing from one
filesystem to another
Bugfixes:
- NFS wakeup of __nfs_lookup_revalidate() needs memory barriers
- NFS improve bounds checking in nfs_fh_to_dentry()
- NFS Fix allocation errors when writing to a NFS file backed
loopback device
- NFSv4: More listxattr fixes
- SUNRPC: fix client handling of TLS alerts
- pNFS block/scsi layout fix for an uninitialised pointer
dereference
- pNFS block/scsi layout fixes for the extent encoding, stripe
mapping, and disk offset overflows
- pNFS layoutcommit work around for RPC size limitations
- pNFS/flexfiles avoid looping when handling fatal errors after
layoutget
- localio: fix various race conditions
Features and cleanups:
- Add NFSv4 support for retrieving the btime
- NFS: Allow folio migration for the case of mode == MIGRATE_SYNC
- NFS: Support using a kernel keyring to store TLS certificates
- NFSv4: Speed up delegation lookup using a hash table
- Assorted cleanups to remove unused variables and struct fields
- Assorted new tracepoints to improve debugging"
* tag 'nfs-for-6.17-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (44 commits)
NFS/localio: nfs_uuid_put() fix the wake up after unlinking the file
NFS/localio: nfs_uuid_put() fix races with nfs_open/close_local_fh()
NFS/localio: nfs_close_local_fh() fix check for file closed
NFSv4: Remove duplicate lookups, capability probes and fsinfo calls
NFS: Fix the setting of capabilities when automounting a new filesystem
sunrpc: fix client side handling of tls alerts
nfs/localio: use read_seqbegin() rather than read_seqbegin_or_lock()
NFS: Fixup allocation flags for nfsiod's __GFP_NORETRY
NFSv4.2: another fix for listxattr
NFS: Fix filehandle bounds checking in nfs_fh_to_dentry()
SUNRPC: Silence warnings about parameters not being described
NFS: Clean up pnfs_put_layout_hdr()/pnfs_destroy_layout_final()
NFS: Fix wakeup of __nfs_lookup_revalidate() in unblock_revalidate()
NFS: use a hash table for delegation lookup
NFS: track active delegations per-server
NFS: move the delegation_watermark module parameter
NFS: cleanup nfs_inode_reclaim_delegation
NFS: cleanup error handling in nfs4_server_common_setup
pNFS/flexfiles: don't attempt pnfs on fatal DS errors
NFS: drop __exit from nfs_exit_keyring
...
Linus Torvalds [Sat, 9 Aug 2025 04:12:43 +0000 (07:12 +0300)]
Merge tag 'v6.17rc-part2-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
"Non-smbdirect:
- Fix null ptr deref caused by delay in global spinlock
initialization
- Two fixes for native symlink creation with SMB3.1.1 POSIX
Extensions
- Fix for socket special file creation with SMB3.1.1 POSIX Exensions
- Reduce lock contention by splitting out mid_counter_lock
- move SMB1 transport code to separate file to reduce module size
when support for legacy servers is disabled
- Two cleanup patches: rename mid_lock to make it clearer what it
protects and one to convert mid flags to bool to make clearer
Smbdirect/RDMA restructuring and fixes:
- Fix for error handling in send done
- Remove unneeded empty packet queue
- Fix put_receive_buffer error path
- Two fixes to recv_done error paths
- Remove unused variable
- Improve response and recvmsg type handling
- Fix handling of incoming message type
- Two cleanup fixes for better handling smbdirect recv io
- Two cleanup fixes for socket spinlock
- Two patches that add socket reassembly struct
- Remove unused connection_status enum
- Use flag in common header for SMBDIRECT_RECV_IO_MAX_SGE
- Two cleanup patches to introduce and use smbdirect send io
- Two cleanup patches to introduce and use smbdirect send_io struct
- Fix to return error if rdma connect takes longer than 5 seconds
- Error logging improvements
- Fix redundand call to init_waitqueue_head
- Remove unneeded wait queue"
* tag 'v6.17rc-part2-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6: (33 commits)
smb: client: only use a single wait_queue to monitor smbdirect connection status
smb: client: don't call init_waitqueue_head(&info->conn_wait) twice in _smbd_get_connection
smb: client: improve logging in smbd_conn_upcall()
smb: client: return an error if rdma_connect does not return within 5 seconds
smb: client: make use of smbdirect_socket.{send,recv}_io.mem.{cache,pool}
smb: smbdirect: add smbdirect_socket.{send,recv}_io.mem.{cache,pool}
smb: client: make use of struct smbdirect_send_io
smb: smbdirect: introduce struct smbdirect_send_io
smb: client: make use of SMBDIRECT_RECV_IO_MAX_SGE
smb: smbdirect: add SMBDIRECT_RECV_IO_MAX_SGE
smb: client: remove unused enum smbd_connection_status
smb: client: make use of smbdirect_socket.recv_io.reassembly.*
smb: smbdirect: introduce smbdirect_socket.recv_io.reassembly.*
smb: client: make use of smb: smbdirect_socket.recv_io.free.{list,lock}
smb: smbdirect: introduce smbdirect_socket.recv_io.free.{list,lock}
smb: client: make use of struct smbdirect_recv_io
smb: smbdirect: introduce struct smbdirect_recv_io
smb: client: make use of smbdirect_socket->recv_io.expected
smb: smbdirect: introduce smbdirect_socket.recv_io.expected
smb: client: remove unused smbd_connection->fragment_reassembly_remaining
...
Linus Torvalds [Sat, 9 Aug 2025 03:52:37 +0000 (06:52 +0300)]
Merge tag 'v6.17rc-part2-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
- Fix limiting repeated connections from same IP
- Fix for extracting shortname when name begins with a dot
- Four smbdirect fixes:
- three fixes to the receive path: potential unmap bug, potential
resource leaks and stale connections, and also potential use
after free race
- cleanup to remove unneeded queue
* tag 'v6.17rc-part2-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
smb: server: Fix extension string in ksmbd_extract_shortname()
ksmbd: limit repeated connections from clients with the same IP
smb: server: let recv_done() avoid touching data_transfer after cleanup/move
smb: server: let recv_done() consistently call put_recvmsg/smb_direct_disconnect_rdma_connection
smb: server: make sure we call ib_dma_unmap_single() only if we called ib_dma_map_single already
smb: server: remove separate empty_recvmsg_queue
Zhang Rui [Tue, 17 Jun 2025 12:48:59 +0000 (20:48 +0800)]
tools/power turbostat: Fix bogus SysWatt for forked program
Similar to delta_cpu(), delta_platform() is called in turbostat main
loop. This ensures accurate SysWatt readings in periodic monitoring mode
$ sudo turbostat -S -q --show power -i 1
CoreTmp PkgTmp PkgWatt CorWatt GFXWatt RAMWatt PKG_% RAM_% SysWatt
60 61 6.21 1.13 0.16 0.00 0.00 0.00 13.07
58 61 6.00 1.07 0.18 0.00 0.00 0.00 12.75
58 61 5.74 1.05 0.17 0.00 0.00 0.00 12.22
58 60 6.27 1.11 0.24 0.00 0.00 0.00 13.55
However, delta_platform() is missing for forked program and causes bogus
SysWatt reporting,
$ sudo turbostat -S -q --show power sleep 1
1.004736 sec
CoreTmp PkgTmp PkgWatt CorWatt GFXWatt RAMWatt PKG_% RAM_% SysWatt
57 58 6.05 1.02 0.16 0.00 0.00 0.00 0.03
Add missing delta_platform() for forked program.
Fixes: e5f687b89bc2 ("tools/power turbostat: Add RAPL psys as a built-in counter") Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Kernels configured with CONFIG_MULTIUSER=n have no cap_get_proc().
Check for ENOSYS to recognize this case, and continue on to
attempt to access the requested MSRs (such as temperature).
Signed-off-by: Calvin Owens <calvin@wbinvd.org> Signed-off-by: Len Brown <len.brown@intel.com>
Calvin Owens [Fri, 13 Jun 2025 16:54:23 +0000 (09:54 -0700)]
tools/power turbostat: Fix build with musl
turbostat.c: In function 'parse_int_file':
turbostat.c:5567:19: error: 'PATH_MAX' undeclared (first use in this function)
5567 | char path[PATH_MAX];
| ^~~~~~~~
turbostat.c: In function 'probe_graphics':
turbostat.c:6787:19: error: 'PATH_MAX' undeclared (first use in this function)
6787 | char path[PATH_MAX];
| ^~~~~~~~
Signed-off-by: Calvin Owens <calvin@wbinvd.org> Reviewed-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Jens Axboe [Fri, 8 Aug 2025 12:35:14 +0000 (06:35 -0600)]
io_uring/memmap: cast nr_pages to size_t before shifting
If the allocated size exceeds UINT_MAX, then it's necessary to cast
the mr->nr_pages value to size_t to prevent it from overflowing. In
practice this isn't much of a concern as the required memory size will
have been validated upfront, and accounted to the user. And > 4GB sizes
will be necessary to make the lack of a cast a problem, which greatly
exceeds normal user locked_vm settings that are generally in the kb to
mb range. However, if root is used, then accounting isn't done, and
then it's possible to hit this issue.
Adam Young [Tue, 15 Jul 2025 00:10:07 +0000 (20:10 -0400)]
mailbox/pcc: support mailbox management of the shared buffer
Define a new, optional, callback that allows the driver to
specify how the return data buffer is allocated. If that callback
is set, mailbox/pcc.c is now responsible for reading from and
writing to the PCC shared buffer.
This also allows for proper checks of the Commnand complete flag
between the PCC sender and receiver.
For Type 4 channels, initialize the command complete flag prior
to accepting messages.
Since the mailbox does not know what memory allocation scheme
to use for response messages, the client now has an optional
callback that allows it to allocate the buffer for a response
message.
When an outbound message is written to the buffer, the mailbox
checks for the flag indicating the client wants an tx complete
notification via IRQ. Upon receipt of the interrupt It will
pair it with the outgoing message. The expected use is to
free the kernel memory buffer for the previous outgoing message.
Signed-off-by: Adam Young <admiyo@os.amperecomputing.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
- net: drop UFO packets (injected via virtio) in udp_rcv_segment()
- eth: mlx5: correctly set gso_segs when LRO is used, avoid false
positive checksum validation errors
- netpoll: prevent hanging NAPI when netcons gets enabled
- phy: mscc: fix parsing of unicast frames for PTP timestamping
- a number of device tree / OF reference leak fixes"
* tag 'net-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (44 commits)
pptp: fix pptp_xmit() error path
net: ti: icssg-prueth: Fix skb handling for XDP_PASS
net: Update threaded state in napi config in netif_set_threaded
selftests: netdevsim: Xfail nexthop test on slow machines
eth: fbnic: Lock the tx_dropped update
eth: fbnic: Fix tx_dropped reporting
eth: fbnic: remove the debugging trick of super high page bias
net: ftgmac100: fix potential NULL pointer access in ftgmac100_phy_disconnect
dt-bindings: net: Replace bouncing Alexandru Tachici emails
dpll: zl3073x: ZL3073X_I2C and ZL3073X_SPI should depend on NET
net/sched: mqprio: fix stack out-of-bounds write in tc entry parsing
Revert "net: mdio_bus: Use devm for getting reset GPIO"
selftests: net: packetdrill: xfail all problems on slow machines
net/packet: fix a race in packet_set_ring() and packet_notifier()
benet: fix BUG when creating VFs
net: airoha: npu: Add missing MODULE_FIRMWARE macros
net: devmem: fix DMA direction on unmapping
ipa: fix compile-testing with qcom-mdt=m
eth: fbnic: unlink NAPIs from queues on error to open
net: Add locking to protect skb->dev access in ip_output
...
Linus Torvalds [Fri, 8 Aug 2025 03:56:55 +0000 (06:56 +0300)]
Merge tag 's390-6.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Alexander Gordeev:
- Support MMIO read/write tracing
- Enable THP swapping and THP migration
- Unmask SLCF bit ("stateless command filtering") introduced with CEX8
cards, so that user space applications like lszcrypt could evaluate
and list this feature
- Fix the value of high_memory variable, so it considers possible
tailing offline memory blocks
- Make vmem_pte_alloc() consistent and always allocate memory of
PAGE_SIZE for page tables. This ensures a page table occupies the
whole page, as the rest of the code assumes
- Fix kernel image end address in the decompressor debug output
- Fix a typo in debug_sprintf_format_fn() comment
* tag 's390-6.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/debug: Fix typo in debug_sprintf_format_fn() comment
s390/boot: Fix startup debugging log
s390/mm: Allocate page table with PAGE_SIZE granularity
s390/mm: Enable THP_SWAP and THP_MIGRATION
s390: Support CONFIG_TRACE_MMIO_ACCESS
s390/mm: Set high_memory at the end of the identity mapping
s390/ap: Unmask SLCF bit in card and queue ap functions sysfs
Linus Torvalds [Fri, 8 Aug 2025 03:48:14 +0000 (06:48 +0300)]
Merge tag 'drm-next-2025-08-08' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"This is the fixes that built up in the merge window, mostly amdgpu and
xe with one i915 display fix, seems like things are pretty good for
rc1.
i915:
- DP LPFS fixes
xe:
- SRIOV: PF fixes and removal of need of module param
- Fix driver unbind around Devcoredump
- Mark xe driver as BROKEN if kernel page size is not 4kB
* tag 'drm-next-2025-08-08' of https://gitlab.freedesktop.org/drm/kernel: (28 commits)
drm/amdgpu: add missing vram lost check for LEGACY RESET
drm/amdgpu/discovery: fix fw based ip discovery
drm/amdkfd: Destroy KFD debugfs after destroy KFD wq
amdgpu/amdgpu_discovery: increase timeout limit for IFWI init
drm/amdgpu: Update SDMA firmware version check for user queue support
drm/amdgpu: Add NULL check for asic_funcs
drm/amd/display: Revert "drm/amd/display: Fix AMDGPU_MAX_BL_LEVEL value"
drm/amd/display: fix a Null pointer dereference vulnerability
drm/amd/display: Add primary plane to commits for correct VRR handling
drm/amdgpu: update mmhub 3.3 client id mappings
drm/amdgpu: update mmhub 3.0.1 client id mappings
drm/amdgpu: Retain job->vm in amdgpu_job_prepare_job
drm/amd/display: Fix DCE 6.0 and 6.4 PLL programming.
drm/amd/display: Don't overwrite dce60_clk_mgr
drm/amdkfd: Fix checkpoint-restore on multi-xcc
drm/amd: Restore cached manual clock settings during resume
drm/amd: Restore cached power limit during resume
drm/amdgpu: Update external revid for GC v9.5.0
drm/amdgpu: Update supported modes for GC v9.5.0
Mark xe driver as BROKEN if kernel page size is not 4kB
...
Linus Torvalds [Fri, 8 Aug 2025 03:43:20 +0000 (06:43 +0300)]
Merge tag 'fbdev-for-6.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes for 6.17-rc1:
- Revert a patch which broke VGA console
- Fix an out-of-bounds access bug which may happen during console
resizing when a console is mapped to a frame buffer
* tag 'fbdev-for-6.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
Revert "vgacon: Add check for vc_origin address range in vgacon_scroll()"
fbdev: Fix vmalloc out-of-bounds write in fast_imageblit
Linus Torvalds [Fri, 8 Aug 2025 03:36:48 +0000 (06:36 +0300)]
Merge tag 'loongarch-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch updates from Huacai Chen:
- Complete KSave registers definition
- Support the mem=<size> kernel parameter
- Support BPF dynamic modification & trampoline
- Add MMC/SDIO controller nodes in dts
- Some bug fixes and other small changes
* tag 'loongarch-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: vDSO: Remove -nostdlib complier flag
LoongArch: dts: Add eMMC/SDIO controller support to Loongson-2K2000
LoongArch: dts: Add SDIO controller support to Loongson-2K1000
LoongArch: dts: Add SDIO controller support to Loongson-2K0500
LoongArch: BPF: Set bpf_jit_bypass_spec_v1/v4()
LoongArch: BPF: Fix the tailcall hierarchy
LoongArch: BPF: Fix jump offset calculation in tailcall
LoongArch: BPF: Add struct ops support for trampoline
LoongArch: BPF: Add basic bpf trampoline support
LoongArch: BPF: Add dynamic code modification support
LoongArch: BPF: Rename and refactor validate_code()
LoongArch: Add larch_insn_gen_{beq,bne} helpers
LoongArch: Don't use %pK through printk() in unwinder
LoongArch: Avoid in-place string operation on FDT content
LoongArch: Support mem=<size> kernel parameter
LoongArch: Make relocate_new_kernel_size be a .quad value
LoongArch: Complete KSave registers definition
Thorsten Blum [Wed, 6 Aug 2025 01:03:49 +0000 (03:03 +0200)]
smb: server: Fix extension string in ksmbd_extract_shortname()
In ksmbd_extract_shortname(), strscpy() is incorrectly called with the
length of the source string (excluding the NUL terminator) rather than
the size of the destination buffer. This results in "__" being copied
to 'extension' rather than "___" (two underscores instead of three).
Use the destination buffer size instead to ensure that the string "___"
(three underscores) is copied correctly.
Cc: stable@vger.kernel.org Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3") Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
Namjae Jeon [Tue, 5 Aug 2025 09:13:13 +0000 (18:13 +0900)]
ksmbd: limit repeated connections from clients with the same IP
Repeated connections from clients with the same IP address may exhaust
the max connections and prevent other normal client connections.
This patch limit repeated connections from clients with the same IP.
Reported-by: tianshuo han <hantianshuo233@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
Dave Airlie [Thu, 7 Aug 2025 19:50:02 +0000 (05:50 +1000)]
Merge tag 'drm-xe-next-fixes-2025-08-06' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-next
- SRIOV: PF fixes and removal of need of module param (Michal)
- Fix driver unbind around Devcoredump (Bala)
- Mark xe driver as BROKEN if kernel page size is not 4kB (Simon)
smb: client: only use a single wait_queue to monitor smbdirect connection status
There's no need for separate conn_wait and disconn_wait queues.
This will simplify the move to common code, the server code
already a single wait_queue for this.
Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: Long Li <longli@microsoft.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <stfrench@microsoft.com>
smb: client: don't call init_waitqueue_head(&info->conn_wait) twice in _smbd_get_connection
It is already called long before we may hit this cleanup code path.
Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: Long Li <longli@microsoft.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <stfrench@microsoft.com>
smb: client: improve logging in smbd_conn_upcall()
Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: Long Li <longli@microsoft.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <stfrench@microsoft.com>
smb: client: return an error if rdma_connect does not return within 5 seconds
This matches the timeout for tcp connections.
Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: Long Li <longli@microsoft.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Fixes: f198186aa9bb ("CIFS: SMBD: Establish SMB Direct connection") Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <stfrench@microsoft.com>
Nam Cao [Thu, 7 Aug 2025 08:10:51 +0000 (10:10 +0200)]
PCI: vmd: Fix wrong kfree() in vmd_msi_free()
vmd_msi_alloc() allocates struct vmd_irq and stashes it into
irq_data->chip_data associated with the VMD's interrupt domain.
vmd_msi_free() extracts the pointer by calling irq_get_chip_data() and
frees it.
irq_get_chip_data() returns the chip_data associated with the top interrupt
domain. This worked in the past because VMD's interrupt domain was the top
domain.
But d7d8ab87e3e7 ("PCI: vmd: Switch to msi_create_parent_irq_domain()")
changed the interrupt domain hierarchy so VMD's interrupt domain is not the
top domain anymore. irq_get_chip_data() now returns the chip_data at the
MSI devices' interrupt domains. It is therefore broken for vmd_msi_free()
to kfree() this chip_data.
Fix by extracting the chip_data associated with the VMD's interrupt domain.
====================
perf/s390: Regression: Move uid filtering to BPF filters
v4: https://lore.kernel.org/bpf/20250806114227.14617-1-iii@linux.ibm.com/
v4 -> v5: Fix a typo in the commit message (Yonghong).
v3: https://lore.kernel.org/bpf/20250805130346.1225535-1-iii@linux.ibm.com/
v3 -> v4: Rename the new field to dont_enable (Alexei, Eduard).
Switch the Fixes: tag in patch 2 (Alexander, Thomas).
Fix typos in the cover letter (Thomas).
v2: https://lore.kernel.org/bpf/20250728144340.711196-1-tmricht@linux.ibm.com/
v2 -> v3: Use no_ioctl_enable in perf.
This series fixes a regression caused by moving UID filtering to BPF.
The regression affects all events that support auxiliary data, most
notably, "cycles" events on s390, but also PT events on Intel. The
symptom is missing events when UID filtering is enabled.
Patch 1 introduces a new option for the
bpf_program__attach_perf_event_opts() function.
Patch 2 makes use of it in perf, and also contains a lot of technical
details of why exactly the problem is occurring.
Thanks to Thomas Richter for the investigation and the initial version
of this fix, and to Jiri Olsa for suggestions.
This allocates the ring buffer for the event 'cycles'. With mmap()
the kernel creates the ring buffer:
perf_mmap(): kernel function to create the event's ring
| buffer to save the sampled data.
|
+-> ring_buffer_attach(): Allocates memory for ring buffer.
| The PMU has auxiliary data setup function. The
| has_aux(event) condition is true and the PMU's
| stop() is called to stop sampling. It is not
| restarted:
|
| if (has_aux(event))
| perf_event_stop(event, 0);
|
+-> cpumsf_pmu_stop():
Hardware sampling is stopped. No samples are generated and saved
anymore.
3. After the event 'cycles' has been mapped, the event is enabled a
second time in:
return immediately because event::state is already set to
PERF_EVENT_STATE_ACTIVE.
This happens on s390, because the event 'cycles' offers the possibility
to save auxilary data. The PMU callbacks setup_aux() and free_aux() are
defined. Without both callback functions, cpumsf_pmu_stop() is not
invoked and sampling continues.
To remedy this, remove the first invocation of
ioctl(..., PERF_EVENT_IOC_ENABLE, ...).
in step (1.) Create the event in step (1.) and enable it in step (3.)
after the ring buffer has been mapped.
Output after:
# ./perf record -aB --synth=no -u 0 -- ./perf test -w thloop 2
[ perf record: Woken up 3 times to write data ]
[ perf record: Captured and wrote 0.876 MB perf.data ]
# ./perf report --stats | grep SAMPLE
SAMPLE events: 16200 (99.5%)
SAMPLE events: 16200
#
The software event succeeded both before and after the patch:
# ./perf record -e cpu-clock -aB --synth=no -u 0 -- \
./perf test -w thloop 2
[ perf record: Woken up 7 times to write data ]
[ perf record: Captured and wrote 2.870 MB perf.data ]
# ./perf report --stats | grep SAMPLE
SAMPLE events: 53506 (99.8%)
SAMPLE events: 53506
#
Fixes: b4c658d4d63d61 ("perf target: Remove uid from target") Suggested-by: Jiri Olsa <jolsa@kernel.org> Tested-by: Thomas Richter <tmricht@linux.ibm.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Co-developed-by: Thomas Richter <tmricht@linux.ibm.com> Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Link: https://lore.kernel.org/r/20250806162417.19666-3-iii@linux.ibm.com Signed-off-by: Alexei Starovoitov <ast@kernel.org>
libbpf: Add the ability to suppress perf event enablement
Automatically enabling a perf event after attaching a BPF prog to it is
not always desirable.
Add a new "dont_enable" field to struct bpf_perf_event_opts. While
introducing "enable" instead would be nicer in that it would avoid
a double negation in the implementation, it would make
DECLARE_LIBBPF_OPTS() less efficient.
Acked-by: Eduard Zingerman <eddyz87@gmail.com> Suggested-by: Jiri Olsa <jolsa@kernel.org> Tested-by: Thomas Richter <tmricht@linux.ibm.com> Co-developed-by: Thomas Richter <tmricht@linux.ibm.com> Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Link: https://lore.kernel.org/r/20250806162417.19666-2-iii@linux.ibm.com Signed-off-by: Alexei Starovoitov <ast@kernel.org>
projects / thirdparty / kernel / stable.git / log
