Tegra already defines all BARs except BAR0 as BAR_RESERVED. This is
sufficient for pci-epf-test to not allocate backing memory and to not call
set_bar() for those BARs. However, marking a BAR as BAR_RESERVED does not
mean that the BAR gets disabled.
The host side driver, pci_endpoint_test, simply does an ioremap for all
enabled BARs and will run tests against all enabled BARs, so it will run
tests against the BARs marked as BAR_RESERVED.
After running the BAR tests (which will write to all enabled BARs), the
inbound address translation is broken. This is because the tegra controller
exposes the ATU Port Logic Structure in BAR4, so when BAR4 is written, the
inbound address translation settings get overwritten.
To avoid this, implement the dw_pcie_ep_ops .init() callback and start off
by disabling all BARs (pci-epf-test will later enable/configure BARs that
are not defined as BAR_RESERVED).
This matches the behavior of other PCIe endpoint drivers: dra7xx, imx6,
layerscape-ep, artpec6, dw-rockchip, qcom-ep, rcar-gen4, and uniphier-ep.
With this, the PCI endpoint kselftest test case CONSECUTIVE_BAR_TEST (which
was specifically made to detect address translation issues) passes.
Fixes: c57247f940e8 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194") Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250922140822.519796-7-cassel@kernel.org
[ changed .init field to .ep_init in pcie_ep_ops struct ] Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cadence PCIe Controller integrated in the TI K3 SoCs supports both
Root-Complex and Endpoint modes of operation. The Glue Layer allows
"strapping" the Mode of operation of the Controller, the Link Speed
and the Link Width. This is enabled by programming the "PCIEn_CTRL"
register (n corresponds to the PCIe instance) within the CTRL_MMR
memory-mapped register space. The "reset-values" of the registers are
also different depending on the mode of operation.
Since the PCIe Controller latches onto the "reset-values" immediately
after being powered on, if the Glue Layer configuration is not done while
the PCIe Controller is off, it will result in the PCIe Controller latching
onto the wrong "reset-values". In practice, this will show up as a wrong
representation of the PCIe Controller's capability structures in the PCIe
Configuration Space. Some such capabilities which are supported by the PCIe
Controller in the Root-Complex mode but are incorrectly latched onto as
being unsupported are:
- Link Bandwidth Notification
- Alternate Routing ID (ARI) Forwarding Support
- Next capability offset within Advanced Error Reporting (AER) capability
Fix this by powering off the PCIe Controller before programming the "strap"
settings and powering it on after that. The runtime PM APIs namely
pm_runtime_put_sync() and pm_runtime_get_sync() will decrement and
increment the usage counter respectively, causing GENPD to power off and
power on the PCIe Controller.
The ACSPCIE module is capable of driving the reference clock required by
the PCIe Endpoint device. It is an alternative to on-board and external
reference clock generators. Enabling the output from the ACSPCIE module's
PAD IO Buffers requires clearing the "PAD IO disable" bits of the
ACSPCIE_PROXY_CTRL register in the CTRL_MMR register space.
Add support to enable the ACSPCIE reference clock output using the optional
device-tree property "ti,syscon-acspcie-proxy-ctrl".
Kernel panics because it detects UFFD inconsistency during
userfaultfd_release_all(). Specifically, a VMA which has a valid pointer
to vma->vm_userfaultfd_ctx, but no UFFD flags in vma->vm_flags.
The inconsistency is caused in ksm_madvise(): when user calls madvise()
with MADV_UNMEARGEABLE on a VMA that is registered for UFFD in MINOR mode,
it accidentally clears all flags stored in the upper 32 bits of
vma->vm_flags.
Assuming x86_64 kernel build, unsigned long is 64-bit and unsigned int and
int are 32-bit wide. This setup causes the following mishap during the &=
~VM_MERGEABLE assignment.
VM_MERGEABLE is a 32-bit constant of type unsigned int, 0x8000'0000.
After ~ is applied, it becomes 0x7fff'ffff unsigned int, which is then
promoted to unsigned long before the & operation. This promotion fills
upper 32 bits with leading 0s, as we're doing unsigned conversion (and
even for a signed conversion, this wouldn't help as the leading bit is 0).
& operation thus ends up AND-ing vm_flags with 0x0000'0000'7fff'ffff
instead of intended 0xffff'ffff'7fff'ffff and hence accidentally clears
the upper 32-bits of its value.
Fix it by changing `VM_MERGEABLE` constant to unsigned long, using the
BIT() macro.
Note: other VM_* flags are not affected: This only happens to the
VM_MERGEABLE flag, as the other VM_* flags are all constants of type int
and after ~ operation, they end up with leading 1 and are thus converted
to unsigned long with leading 1s.
Note 2:
After commit 31defc3b01d9 ("userfaultfd: remove (VM_)BUG_ON()s"), this is
no longer a kernel BUG, but a WARNING at the same place:
[ 45.595973] WARNING: CPU: 1 PID: 2474 at mm/userfaultfd.c:2067
but the root-cause (flag-drop) remains the same.
[akpm@linux-foundation.org: rust bindgen wasn't able to handle BIT(), from Miguel] Link: https://lore.kernel.org/oe-kbuild-all/202510030449.VfSaAjvd-lkp@intel.com/ Link: https://lkml.kernel.org/r/20251001090353.57523-2-acsjakub@amazon.de Fixes: 7677f7fd8be7 ("userfaultfd: add minor fault registration mode") Signed-off-by: Jakub Acs <acsjakub@amazon.de> Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> Acked-by: David Hildenbrand <david@redhat.com> Acked-by: SeongJae Park <sj@kernel.org> Tested-by: Alice Ryhl <aliceryhl@google.com> Tested-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> Cc: Xu Xin <xu.xin16@zte.com.cn> Cc: Chengming Zhou <chengming.zhou@linux.dev> Cc: Peter Xu <peterx@redhat.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[acsjakub@amazon.de: adapt rust bindgen const to older versions] Signed-off-by: Jakub Acs <acsjakub@amazon.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ksmbd.mount will give each interfaces list and bind_interfaces_only flags
to ksmbd server. Previously, the interfaces list was sent only
when bind_interfaces_only was enabled.
ksmbd server browse only interfaces list given from ksmbd.conf on
FSCTL_QUERY_INTERFACE_INFO IOCTL.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian Norris [Mon, 20 Oct 2025 20:41:36 +0000 (13:41 -0700)]
PCI/sysfs: Ensure devices are powered for config reads (part 2)
Commit 48991e493507 ("PCI/sysfs: Ensure devices are powered for config
reads") was applied to various linux-stable trees. However, prior to
6.12.y, we do not have commit d2bd39c0456b ("PCI: Store all PCIe
Supported Link Speeds"). Therefore, we also need to apply the change to
max_link_speed_show().
This was pointed out here:
Re: Patch "PCI/sysfs: Ensure devices are powered for config reads" has been added to the 6.6-stable tree
https://lore.kernel.org/all/aPEMIreBYZ7yk3cm@google.com/
Original change description follows:
The "max_link_width", "current_link_speed", "current_link_width",
"secondary_bus_number", and "subordinate_bus_number" sysfs files all access
config registers, but they don't check the runtime PM state. If the device
is in D3cold or a parent bridge is suspended, we may see -EINVAL, bogus
values, or worse, depending on implementation details.
Wrap these access in pci_config_pm_runtime_{get,put}() like most of the
rest of the similar sysfs attributes.
Notably, "max_link_speed" does not access config registers; it returns a
cached value since d2bd39c0456b ("PCI: Store all PCIe Supported Link
Speeds").
This is a backport of e4f574ca9c6d specifically for the 6.6-stable
kernel. It differs from the upstream version mainly in that it's
working around the absence of some 6.12-era commits:
- 1459ad57673b nfsd: Move error code mapping to per-version proc code.
- 0a183f24a7ae NFSD: Handle @rqstp == NULL in check_nfsd_access()
- 5e66d2d92a1c nfsd: factor out __fh_verify to allow NULL rqstp to be
passed
A while back I had reported that an NFSv3 client could successfully
mount using '-o xprtsec=none' an export that had been exported with
'xprtsec=tls:mtls'. By "successfully" I mean that the mount command
would succeed and the mount would show up in /proc/mount. Attempting
to do anything futher with the mount would be met with NFS3ERR_ACCES.
Transport Layer Security isn't an RPC security flavor or pseudo-flavor,
so we shouldn't be conflating them when determining whether the access
checks can be bypassed. Split check_nfsd_access() into two helpers, and
have fh_verify() call the helpers directly since fh_verify() has
logic that allows one or both of the checks to be skipped. All other
sites will continue to call check_nfsd_access().
Link: https://lore.kernel.org/linux-nfs/ZjO3Qwf_G87yNXb2@aion/ Fixes: 9280c5774314 ("NFSD: Handle new xprtsec= export option") Signed-off-by: Scott Mayhew <smayhew@redhat.com> Acked-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was backward compatibility in the terms of mailbox API. Various
drivers from various OSes supporting 10G adapters from Intel portfolio
could easily negotiate mailbox API.
This convention has been broken since introducing API 1.4.
Commit 0062e7cc955e ("ixgbevf: add VF IPsec offload code") added support
for IPSec which is specific only for the kernel ixgbe driver. None of the
rest of the Intel 10G PF/VF drivers supports it. And actually lack of
support was not included in the IPSec implementation - there were no such
code paths. No possibility to negotiate support for the feature was
introduced along with introduction of the feature itself.
Commit 339f28964147 ("ixgbevf: Add support for new mailbox communication
between PF and VF") increasing API version to 1.5 did the same - it
introduced code supported specifically by the PF ESX driver. It altered API
version for the VF driver in the same time not touching the version
defined for the PF ixgbe driver. It led to additional discrepancies,
as the code provided within API 1.6 cannot be supported for Linux ixgbe
driver as it causes crashes.
The issue was noticed some time ago and mitigated by Jake within the commit d0725312adf5 ("ixgbevf: stop attempting IPSEC offload on Mailbox API 1.5").
As a result we have regression for IPsec support and after increasing API
to version 1.6 ixgbevf driver stopped to support ESX MBX.
To fix this mess add new mailbox op asking PF driver about supported
features. Basing on a response determine whether to set support for IPSec
and ESX-specific enhanced mailbox.
New mailbox op, for compatibility purposes, must be added within new API
revision, as API version of OOT PF & VF drivers is already increased to
1.6 and doesn't incorporate features negotiate op.
Features negotiation mechanism gives possibility to be extended with new
features when needed in the future.
Reported-by: Jacob Keller <jacob.e.keller@intel.com> Closes: https://lore.kernel.org/intel-wired-lan/20241101-jk-ixgbevf-mailbox-v1-5-fixes-v1-0-f556dc9a66ed@intel.com/ Fixes: 0062e7cc955e ("ixgbevf: add VF IPsec offload code") Fixes: 339f28964147 ("ixgbevf: Add support for new mailbox communication between PF and VF") Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20251009-jk-iwl-net-2025-10-01-v3-4-ef32a425b92a@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
E610 adapters no longer use the VFLINKS register to read PF's link
speed and linkup state. As a result VF driver cannot get actual link
state and it incorrectly reports 10G which is the default option.
It leads to a situation where even 1G adapters print 10G as actual
link speed. The same happens when PF driver set speed different than 10G.
Add new mailbox operation to let the VF driver request a PF driver
to provide actual link data. Update the mailbox api to v1.6.
Incorporate both ways of getting link status within the legacy
ixgbe_check_mac_link_vf() function.
Fixes: 4c44b450c69b ("ixgbevf: Add support for Intel(R) E610 device") Co-developed-by: Andrzej Wilczynski <andrzejx.wilczynski@intel.com> Signed-off-by: Andrzej Wilczynski <andrzejx.wilczynski@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20251009-jk-iwl-net-2025-10-01-v3-2-ef32a425b92a@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: a7075f501bd3 ("ixgbevf: fix mailbox API compatibility by negotiating supported features") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Intel(R) E610 Series of network devices. The E610
is based on X550 but adds firmware managed link, enhanced security
capabilities and support for updated server manageability
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: a7075f501bd3 ("ixgbevf: fix mailbox API compatibility by negotiating supported features") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do read-modify-write so that we re-use the characterized reset value as
specified in TRM [1] to program calibration wait time which defines number
of cycles to wait for after startup state machine is in bandgap enable
state.
This fixes PLL lock timeout error faced while using RPi DSI Panel on TI's
AM62L and J721E SoC since earlier calibration wait time was getting
overwritten to zero value thus failing the PLL to lockup and causing
timeout.
Unlike other strings in the ext4 superblock, we rely on tune2fs to
make sure s_mount_opts is NUL terminated. Harden
parse_apply_sb_mount_options() by treating s_mount_opts as a potential
__nonstring.
Cc: stable@vger.kernel.org Fixes: 8b67f04ab9de ("ext4: Add mount options in superblock") Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Message-ID: <20250916-tune2fs-v2-1-d594dc7486f0@mit.edu> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[ added sizeof() third argument to strscpy_pad() ] Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When user calls open_by_handle_at() on some inode that is not cached, we
will create disconnected dentry for it. If such dentry is a directory,
exportfs_decode_fh_raw() will then try to connect this dentry to the
dentry tree through reconnect_path(). It may happen for various reasons
(such as corrupted fs or race with rename) that the call to
lookup_one_unlocked() in reconnect_one() will fail to find the dentry we
are trying to reconnect and instead create a new dentry under the
parent. Now this dentry will not be marked as disconnected although the
parent still may well be disconnected (at least in case this
inconsistency happened because the fs is corrupted and .. doesn't point
to the real parent directory). This creates inconsistency in
disconnected flags but AFAICS it was mostly harmless. At least until
commit f1ee616214cb ("VFS: don't keep disconnected dentries on d_anon")
which removed adding of most disconnected dentries to sb->s_anon list.
Thus after this commit cleanup of disconnected dentries implicitely
relies on the fact that dput() will immediately reclaim such dentries.
However when some leaf dentry isn't marked as disconnected, as in the
scenario described above, the reclaim doesn't happen and the dentries
are "leaked". Memory reclaim can eventually reclaim them but otherwise
they stay in memory and if umount comes first, we hit infamous "Busy
inodes after unmount" bug. Make sure all dentries created under a
disconnected parent are marked as disconnected as well.
Reported-by: syzbot+1d79ebe5383fc016cf07@syzkaller.appspotmail.com Fixes: f1ee616214cb ("VFS: don't keep disconnected dentries on d_anon") CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Christian Brauner <brauner@kernel.org>
[ relocated DCACHE_DISCONNECTED propagation from d_alloc_parallel() to d_alloc() ] Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a kernel panic due to WARN_ONCE when panic_on_warn is set.
This issue occurs when writeback is triggered due to sync call for an
opened file(ie, writeback reason is WB_REASON_SYNC). When f2fs balance
is needed at sync path, flush for quota_release_work is triggered.
By default quota_release_work is queued to "events_unbound" queue which
does not have WQ_MEM_RECLAIM flag. During f2fs balance "writeback"
workqueue tries to flush quota_release_work causing kernel panic due to
MEM_RECLAIM flag mismatch errors.
This patch creates dedicated workqueue with WQ_MEM_RECLAIM flag
for work quota_release_work.
When seq_nr wraps around, the next reorder job with seq 0 is hashed to
the first CPU in padata_do_serial(). Correspondingly, need reset pd->cpu
to the first one when pd->processed wraps around. Otherwise, if the
number of used CPUs is not a power of 2, padata_find_next() will be
checking a wrong list, hence deadlock.
Fixes: 6fc4dbcf0276 ("padata: Replace delayed timer with immediate workqueue in padata_reorder") Cc: <stable@vger.kernel.org> Signed-off-by: Xiao Liang <shaw.leon@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[ relocated fix from padata_reorder() function to padata_find_next() ] Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we're removing rmap records for crosslinked blocks, use deferred
intent items so that we can try to free/unmap as many of the old data
structure's blocks as we can in the same transaction as the commit.
Cc: <stable@vger.kernel.org> # v6.6 Fixes: 1c7ce115e52106 ("xfs: reap large AG metadata extents when possible") Signed-off-by: "Darrick J. Wong" <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de>
[ adjusted xfs_rmap_free_extent() and xfs_refcount_free_cow_extent() ] Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do as in suspend, skip resume configuration steps if the device is already
pm_runtime suspended. This avoids reconfiguring a device that is already
in the correct low-power state and ensures that pm_runtime handles the
power state transitions properly.
Fixes: 31c24c1e93c3 ("iio: imu: inv_icm42600: add core of new inv_icm42600 driver") Signed-off-by: Sean Nyekjaer <sean@geanix.com> Link: https://patch.msgid.link/20250901-icm42pmreg-v3-3-ef1336246960@geanix.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[ adjusted context due to missing APEX/WoM features in older kernel version ] Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move all DMA aligned buffers together at the end of the structure.
1. Timestamp anynomous structure is not used with DMA so it doesn't
belong after __aligned(IIO_DMA_MINALIGN).
2. struct inv_icm42600_fifo contains it's own __aligned(IIO_DMA_MINALIGN)
within it at the end so it should not be after __aligned(IIO_DMA_MINALIGN)
in the outer struct either.
3. Normally 1 would have been considered a bug, but because of the extra
alignment from 2, it actually was OK, but we shouldn't be relying on such
quirks.
PLL lockup and O_CMN_READY assertion can only happen after common state
machine gets enabled by programming DPHY_CMN_SSM register, but driver was
polling them before the common state machine was enabled which is
incorrect. This is as per the DPHY initialization sequence as mentioned in
J721E TRM [1] at section "12.7.2.4.1.2.1 Start-up Sequence Timing Diagram".
It shows O_CMN_READY polling at the end after common configuration pin
setup where the common configuration pin setup step enables state machine
as referenced in "Table 12-1533. Common Configuration-Related Setup
mentions state machine"
To fix this :
- Add new function callbacks for polling on PLL lock and O_CMN_READY
assertion.
- As state machine and clocks get enabled in power_on callback only, move
the clock related programming part from configure callback to power_on
callback and poll for the PLL lockup and O_CMN_READY assertion after state
machine gets enabled.
- The configure callback only saves the PLL configuration received from the
client driver which will be applied later on in power_on callback.
- Add checks to ensure configure is called before power_on and state
machine is in disabled state before power_on callback is called.
- Disable state machine in power_off so that client driver can re-configure
the PLL by following up a power_off, configure, power_on sequence.
The DPHY driver does not return the actual hs_clk_rate, so the DSI
driver has no idea what clock was actually achieved. Set the realized
hs_clk_rate to the opts struct, so that the DSI driver gets it back.
Rework the power management in inv_icm42600_core_probe() to use
devm_pm_runtime_set_active_enabled(), which simplifies the runtime PM
setup by handling activation and enabling in one step.
Remove the separate inv_icm42600_disable_pm callback, as it's no longer
needed with the devm-managed approach.
Using devm_pm_runtime_enable() also fixes the missing disable of
autosuspend.
Update inv_icm42600_disable_vddio_reg() to only disable the regulator if
the device is not suspended i.e. powered-down, preventing unbalanced
disables.
Also remove redundant error msg on regulator_disable(), the regulator
framework already emits an error message when regulator_disable() fails.
This simplifies the PM setup and avoids manipulating the usage counter
unnecessarily.
Fixes: 31c24c1e93c3 ("iio: imu: inv_icm42600: add core of new inv_icm42600 driver") Signed-off-by: Sean Nyekjaer <sean@geanix.com> Link: https://patch.msgid.link/20250901-icm42pmreg-v3-1-ef1336246960@geanix.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mounting file systems with a log that was dirtied on i386 on
other architectures or vice versa, log recovery is unhappy:
[ 11.068052] XFS (vdb): Torn write (CRC failure) detected at log block 0x2. Truncating head block from 0xc.
This is because the CRCs generated by i386 and other architectures
always diff. The reason for that is that sizeof(struct xlog_rec_header)
returns different values for i386 vs the rest (324 vs 328), because the
struct is not sizeof(uint64_t) aligned, and i386 has odd struct size
alignment rules.
This issue goes back to commit 13cdc853c519 ("Add log versioning, and new
super block field for the log stripe") in the xfs-import tree, which
adds log v2 support and the h_size field that causes the unaligned size.
At that time it only mattered for the crude debug only log header
checksum, but with commit 0e446be44806 ("xfs: add CRC checks to the log")
it became a real issue for v5 file system, because now there is a proper
CRC, and regular builds actually expect it match.
Fix this by allowing checksums with and without the padding.
Fixes: 0e446be44806 ("xfs: add CRC checks to the log") Cc: <stable@vger.kernel.org> # v3.8 Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Carlos Maiolino <cem@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
old_crc is a very misleading name. Rename it to expected_crc as that
described the usage much better.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Stable-dep-of: e747883c7d73 ("xfs: fix log CRC mismatches between i386 and other architectures") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The data type of loca_last_write_offset is newoffset4 and is switched
on a boolean value, no_newoffset, that indicates if a previous write
occurred or not. If no_newoffset is FALSE, an offset is not given.
This means that client does not try to update the file size. Thus,
server should not try to calculate new file size and check if it fits
into the segment range. See RFC 8881, section 12.5.4.2.
Sometimes the current incorrect logic may cause clients to hang when
trying to sync an inode. If layoutcommit fails, the client marks the
inode as dirty again.
Fixes: 9cf514ccfacb ("nfsd: implement pNFS operations") Cc: stable@vger.kernel.org Co-developed-by: Konstantin Evtushenko <koevtushenko@yandex.com> Signed-off-by: Konstantin Evtushenko <koevtushenko@yandex.com> Signed-off-by: Sergey Bashirov <sergeybashirov@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
[ removed rqstp parameter from proc_layoutcommit ] Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove dprintk in nfsd4_layoutcommit. These are not needed
in day to day usage, and the information is also available
in Wireshark when capturing NFS traffic.
Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sergey Bashirov <sergeybashirov@gmail.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Stable-dep-of: d68886bae76a ("NFSD: Fix last write offset handling in layoutcommit") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compilers may optimize the layout of C structures, so we should not rely
on sizeof struct and memcpy to encode and decode XDR structures. The byte
order of the fields should also be taken into account.
This patch adds the correct functions to handle the deviceid4 structure
and removes the pad field, which is currently not used by NFSD, from the
runtime state. The server's byte order is preserved because the deviceid4
blob on the wire is only used as a cookie by the client.
Signed-off-by: Sergey Bashirov <sergeybashirov@gmail.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Stable-dep-of: d68886bae76a ("NFSD: Fix last write offset handling in layoutcommit") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit c0e473a0d226 ("block: fix race between set_blocksize and read
paths") was merged, set_blocksize() called by sb_set_blocksize() now locks
the inode of the backing device file. As a result of this change, syzbot
started reporting deadlock warnings due to a circular dependency involving
the semaphore "ns_sem" of the nilfs object, the inode lock of the backing
device file, and the locks that this inode lock is transitively dependent
on.
This is caused by a new lock dependency added by the above change, since
init_nilfs() calls sb_set_blocksize() in the lock section of "ns_sem".
However, these warnings are false positives because init_nilfs() is called
in the early stage of the mount operation and the filesystem has not yet
started.
The reason why "ns_sem" is locked in init_nilfs() was to avoid a race
condition in nilfs_fill_super() caused by sharing a nilfs object among
multiple filesystem instances (super block structures) in the early
implementation. However, nilfs objects and super block structures have
long ago become one-to-one, and there is no longer any need to use the
semaphore there.
So, fix this issue by removing the use of the semaphore "ns_sem" in
init_nilfs().
Link: https://lkml.kernel.org/r/20250503053327.12294-1-konishi.ryusuke@gmail.com Fixes: c0e473a0d226 ("block: fix race between set_blocksize and read paths") Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Reported-by: syzbot+00f7f5b884b117ee6773@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=00f7f5b884b117ee6773 Tested-by: syzbot+00f7f5b884b117ee6773@syzkaller.appspotmail.com Reported-by: syzbot+f30591e72bfc24d4715b@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=f30591e72bfc24d4715b Tested-by: syzbot+f30591e72bfc24d4715b@syzkaller.appspotmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mahmoud Adam <mngyadam@amazon.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the new large sector size support, it's now the case that
set_blocksize can change i_blksize and the folio order in a manner that
conflicts with a concurrent reader and causes a kernel crash.
Specifically, let's say that udev-worker calls libblkid to detect the
labels on a block device. The read call can create an order-0 folio to
read the first 4096 bytes from the disk. But then udev is preempted.
Next, someone tries to mount an 8k-sectorsize filesystem from the same
block device. The filesystem calls set_blksize, which sets i_blksize to
8192 and the minimum folio order to 1.
Now udev resumes, still holding the order-0 folio it allocated. It then
tries to schedule a read bio and do_mpage_readahead tries to create
bufferheads for the folio. Unfortunately, blocks_per_folio == 0 because
the page size is 4096 but the blocksize is 8192 so no bufferheads are
attached and the bh walk never sets bdev. We then submit the bio with a
NULL block device and crash.
Therefore, truncate the page cache after flushing but before updating
i_blksize. However, that's not enough -- we also need to lock out file
IO and page faults during the update. Take both the i_rwsem and the
invalidate_lock in exclusive mode for invalidations, and in shared mode
for read/write operations.
I don't know if this is the correct fix, but xfs/259 found it.
Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Luis Chamberlain <mcgrof@kernel.org> Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Link: https://lore.kernel.org/r/174543795699.4139148.2086129139322431423.stgit@frogsfrogsfrogs Signed-off-by: Jens Axboe <axboe@kernel.dk>
[ use bdev->bd_inode instead ] Signed-off-by: Mahmoud Adam <mngyadam@amazon.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the workaround for Neoverse-V3AE, and document this.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: James Morse <james.morse@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... in section A.6.1 ("MIDR_EL1, Main ID Register").
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: James Morse <james.morse@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The issue takes place if the length field of struct hfsplus_unistr
is bigger than HFSPLUS_MAX_STRLEN. The patch simply checks
the length of comparing strings. And if the strings' length
is bigger than HFSPLUS_MAX_STRLEN, then it is corrected
to this value.
v2
The string length correction has been added for hfsplus_strcmp().
Reported-by: Jiaming Zhang <r772577952@gmail.com> Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
cc: Yangtao Li <frank.li@vivo.com>
cc: linux-fsdevel@vger.kernel.org
cc: syzkaller@googlegroups.com Link: https://lore.kernel.org/r/20250919191243.1370388-1-slava@dubeyko.com Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
test_parse_test_list_file writes some data to
/tmp/bpf_arg_parsing_test.XXXXXX and parse_test_list_file() will read
the data back. However, after writing data to that file, we forget to
call fsync() and it's causing testing failure in my laptop. This patch
helps fix it by adding the missing fsync() call.
Fixes: 64276f01dce8 ("selftests/bpf: Test_progs can read test lists from file") Signed-off-by: Xing Guo <higuoxing@gmail.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20251016035330.3217145-1-higuoxing@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
HID_DG_PEN devices should have a suffix of "Stylus", as pointed out by
commit c0ee1d571626 ("HID: hid-input: Add suffix also for HID_DG_PEN").
However, on multitouch devices, these suffixes may be overridden. Before
that commit, HID_DG_PEN devices would get the "Stylus" suffix, but after
that, multitouch would override them to have an "UNKNOWN" suffix. Just add
HID_DG_PEN to the list of non-overriden suffixes in multitouch.
Commit 581c4484769e ("HID: input: map digitizer battery usage") added
handling of battery events for digitizers (typically for batteries
presented in stylii). Digitizers typically report correct battery levels
only when stylus is actively touching the surface, and in other cases
they may report battery level of 0. To avoid confusing consumers of the
battery information the code was added to filer out reports with 0
battery levels.
However there exist other kinds of devices that may legitimately report
0 battery levels. Fix this by filtering out 0-level reports only for
digitizer usages, and continue reporting them for other kinds of devices
(Smart Batteries, etc).
In try_to_register_card(), the return value of usb_ifnum_to_if() is
passed directly to usb_interface_claimed() without a NULL check, which
will lead to a NULL pointer dereference when creating an invalid
USB audio device. Fix this by adding a check to ensure the interface
pointer is valid before passing it to usb_interface_claimed().
One way we can crash there is if set.cnt zero, which is checked for with
ASSERT_EQ() above, but we proceed after this regardless of the outcome.
Instead of crashing, we should bail out with test failure early.
Similarly, if parse_test_list_file() fails, we shouldn't be even looking
at set, so bail even earlier if ASSERT_OK() fails.
Fixes: 64276f01dce8 ("selftests/bpf: Test_progs can read test lists from file") Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Tested-by: Ihor Solodrai <ihor.solodrai@linux.dev> Link: https://lore.kernel.org/r/20251014202037.72922-1-andrii@kernel.org Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, if find_and_map_user_pages() takes a DMA xfer request from the
user with a length field set to 0, or in a rare case, the host receives
QAIC_TRANS_DMA_XFER_CONT from the device where resources->xferred_dma_size
is equal to the requested transaction size, the function will return 0
before allocating an sgt or setting the fields of the dma_xfer struct.
In that case, encode_addr_size_pairs() will try to access the sgt which
will lead to a general protection fault.
Return an EINVAL in case the user provides a zero-sized ALP, or the device
requests continuation after all of the bytes have been transferred.
Fixes: 96d3c1cadedb ("accel/qaic: Clean up integer overflow checking in map_user_pages()") Signed-off-by: Youssef Samir <quic_yabdulra@quicinc.com> Signed-off-by: Youssef Samir <youssef.abdulrahman@oss.qualcomm.com> Reviewed-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com> Reviewed-by: Carl Vanderlip <carl.vanderlip@oss.qualcomm.com> Signed-off-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com> Link: https://lore.kernel.org/r/20251007122320.339654-1-youssef.abdulrahman@oss.qualcomm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix spelling of CIP_NO_HEADER to prevent a kernel-doc warning.
Warning: amdtp-stream.h:57 Enum value 'CIP_NO_HEADER' not described in enum 'cip_flags'
Warning: amdtp-stream.h:57 Excess enum value '%CIP_NO_HEADERS' description in 'cip_flags'
The check for some lost idle pelt time should be always done when
pick_next_task_fair() fails to pick a task and not only when we call it
from the fair fast-path.
The case happens when the last running task on rq is a RT or DL task. When
the latter goes to sleep and the /Sum of util_sum of the rq is at the max
value, we don't account the lost of idle time whereas we should.
Fixes: 67692435c411 ("sched: Rework pick_next_task() slow-path") Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The vop2_plane_atomic_check() function incorrectly checks
drm_rect_width(dest) twice instead of verifying both width and height.
Fix the second condition to use drm_rect_height(dest) so that invalid
destination rectangles with height < 4 are correctly rejected.
CIK GPUs such as Hawaii appear to use PP_TABLE_V0 in which case
the shutdown temperature is hardcoded in smu7_init_dpm_defaults
and is already multiplied by 1000. The value was mistakenly
multiplied another time by smu7_get_thermal_temperature_range.
Fixes: 4ba082572a42 ("drm/amd/powerplay: export the thermal ranges of VI asics (V2)") Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/1676 Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
GuC IRQ and tasklet handler receive just single G2H message, and let other
messages to be received from next tasklet. During this chained tasklet
process, if reset process started, communication will be disabled.
Skip warning for this condition.
Stress testing the audio jack hotplug handling on a few Steam Deck units
revealed that the debounce circuit is responsible for having a negative
impact on the detection reliability, e.g. in some cases the ejection
interrupt is not fired, while in other instances it goes into a kind of
invalid state and generates a flood of misleading interrupts.
Add new entries to the DMI table introduced via commit 1bc40efdaf4a
("ASoC: nau8821: Add DMI quirk mechanism for active-high jack-detect")
and extend the quirk logic to allow bypassing the debounce circuit used
for jack detection on Valve Steam Deck LCD and OLED models.
While at it, rename existing NAU8821_JD_ACTIVE_HIGH quirk bitfield to
NAU8821_QUIRK_JD_ACTIVE_HIGH. This should help improve code readability
by differentiating from similarly named register bits.
Instead of adding yet another utility function for dealing with the
interrupt clearing register, generalize nau8821_int_status_clear_all()
by renaming it to nau8821_irq_status_clear(), whilst introducing a
second parameter to allow restricting the operation scope to a single
interrupt instead of the whole range of active IRQs.
While at it, also fix a spelling typo in the comment block.
Note this is mainly a prerequisite for subsequent patches aiming to
address some deficiencies in the implementation of the interrupt
handler. Thus the presence of the Fixes tag below is intentional, to
facilitate backporting.
The microphone detection work scheduled by a prior jack insertion
interrupt may still be in a pending state or under execution when a jack
ejection interrupt has been fired.
This might lead to a racing condition or nau8821_jdet_work() completing
after nau8821_eject_jack(), which will override the currently
disconnected state of the jack and incorrectly report the headphone or
the headset as being connected.
Cancel any pending jdet_work or wait for its execution to finish before
attempting to handle the ejection interrupt.
Proceed similarly before launching the eject handler as a consequence of
detecting an invalid insert interrupt.
The gain ranges specified in Renesas IDT821034 codec documentation
are [-3dB;+13dB] in the transmit path (ADC) and [-13dB;+3dB] in the
receive path (DAC). Allthough the registers allow programming values
outside those ranges, the signal S/N and distorsion are only
guaranteed in the specified ranges.
There is now a new LT9211 rev. U5, which reports chip ID 0x18 0x01 0xe4 .
The previous LT9211 reported chip ID 0x18 0x01 0xe3 , which is what the
driver checks for right now. Since there is a possibility there will be
yet another revision of the LT9211 in the future, drop the last version
nibble check to allow all future revisions of the chip to work with this
driver.
This fix makes LT9211 rev. U5 work with this driver.
When adding a kprobe such as "p:probe/tcp_sendmsg _text+15392192",
arch_check_kprobe would start iterating all instructions starting from
_text until the probed address. Not only is this very inefficient, but
literal values in there (e.g. left by function patching) are
misinterpreted in a way that causes a desync.
Fix this by doing it like x86: start the iteration at the closest
preceding symbol instead of the given starting point.
Fixes: 87f48c7ccc73 ("riscv: kprobe: Fixup kernel panic when probing an illegal position") Signed-off-by: Fabian Vogt <fvogt@suse.de> Signed-off-by: Marvin Friedrich <marvin.friedrich@suse.com> Acked-by: Guo Ren <guoren@kernel.org> Link: https://lore.kernel.org/r/6191817.lOV4Wx5bFT@fvogt-thinkpad Signed-off-by: Paul Walmsley <pjw@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For queue-depth I/O policy, this patch fixes unbalanced I/Os across
nvme multipaths.
Issue Description:
The RETRY disposition incorrectly increments ns->ctrl->nr_active
counter and reinitializes iostat start-time. In such cases nr_active
counter never goes back to zero until that path disconnects and
reconnects.
Such a path is not chosen for new I/Os if multiple RETRY cases on a given
a path cause its queue-depth counter to be artificially higher compared
to other paths. This leads to unbalanced I/Os across paths.
The patch skips incrementing nr_active if NVME_MPATH_CNT_ACTIVE is already
set. And it skips restarting io stats if NVME_MPATH_IO_STATS is already set.
base-commit: e989a3da2d371a4b6597ee8dee5c72e407b4db7a Fixes: d4d957b53d91eeb ("nvme-multipath: support io stats on the mpath device") Signed-off-by: Amit Chaudhary <achaudhary@purestorage.com> Reviewed-by: Randy Jennings <randyj@purestorage.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Convert `lan78xx_init_mac_address` to return error codes and handle
failures in register read and write operations. Update `lan78xx_reset`
to check for errors during MAC address initialization and propagate them
appropriately.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20241209130751.703182-3-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 8d93ff40d49d ("net: usb: lan78xx: fix use of improperly initialized dev->chipid in lan78xx_reset") Signed-off-by: Sasha Levin <sashal@kernel.org>
With async crypto, we rely on tx_work to actually transmit records
once encryption completes. But while send() is running, both the
tx_lock and socket lock are held, so tx_work_handler cannot process
the queue of encrypted records, and simply reschedules itself. During
a large send(), this could last a long time, and use a lot of memory.
Transmit any pending encrypted records before restarting the main
loop of tls_sw_sendmsg_locked.
Async decryption calls tls_strp_msg_hold to create a clone of the
input skb to hold references to the memory it uses. If we fail to
allocate that clone, proceeding with async decryption can lead to
various issues (UAF on the skb, writing into userspace memory after
the recv() call has returned).
In this case, wait for all pending decryption requests.
When userspace wants to send a non-DATA record (via the
TLS_SET_RECORD_TYPE cmsg), we need to send any pending data from a
previous MSG_MORE send() as a separate DATA record. If that DATA record
is encrypted asynchronously, tls_handle_open_record will return
-EINPROGRESS. This is currently treated as an error by
tls_process_cmsg, and it will skip setting record_type to the correct
value, but the caller (tls_sw_sendmsg_locked) handles that return
value correctly and proceeds with sending the new message with an
incorrect record_type (DATA instead of whatever was requested in the
cmsg).
Always set record_type before handling the open record. If
tls_handle_open_record returns an error, record_type will be
ignored. If it succeeds, whether with synchronous crypto (returning 0)
or asynchronous (returning -EINPROGRESS), the caller will proceed
correctly.
If we hit an error during the main loop of tls_sw_sendmsg_locked (eg
failed allocation), we jump to send_end and immediately
return. Previous iterations may have queued async encryption requests
that are still pending. We should wait for those before returning, as
we could otherwise be reading from memory that userspace believes
we're not using anymore, which would be a sort of use-after-free.
This is similar to what tls_sw_recvmsg already does: failures during
the main loop jump to the "wait for async" code, not straight to the
unlock/return.
When asynchronous encryption is used KTLS sends out the final data at
proto->close time. This becomes problematic when the task calling
close() receives a signal. In this case it can happen that
tcp_sendmsg_locked() called at close time returns -ERESTARTSYS and the
final data is not sent.
The described situation happens when KTLS is used in conjunction with
io_uring, as io_uring uses task_work_add() to add work to the current
userspace task. A discussion of the problem along with a reproducer can
be found in [1] and [2]
Fix this by waiting for the asynchronous encryption to be completed on
the final message. With this there is no data left to be sent at close
time.
During tls_sw_sendmsg_locked, we pre-allocate the encrypted message
for the size we're expecting to send during the current iteration, but
we may end up sending less, for example when splicing: if we're
getting the data from small fragments of memory, we may fill up all
the slots in the skmsg with less data than expected.
In this case, we need to trim the encrypted message to only the length
we actually need, to avoid pushing uninitialized bytes down the
underlying TCP socket.
Neal reported that using neper tcp_stream with TCP_TX_DELAY
set to 50ms would often lead to flows stuck in a small cwnd mode,
regardless of the congestion control.
While tcp_stream sets TCP_TX_DELAY too late after the connect(),
it highlighted two kernel bugs.
The following heuristic in tcp_tso_should_defer() seems wrong
for large RTT:
delta = tp->tcp_clock_cache - head->tstamp;
/* If next ACK is likely to come too late (half srtt), do not defer */
if ((s64)(delta - (u64)NSEC_PER_USEC * (tp->srtt_us >> 4)) < 0)
goto send_now;
If next ACK is expected to come in more than 1 ms, we should
not defer because we prefer a smooth ACK clocking.
While blamed commit was a step in the good direction, it was not
generic enough.
Another patch fixing TCP_TX_DELAY for established flows
will be proposed when net-next reopens.
During interface toggle operations (ifdown/ifup), the driver currently
resets the local helper variable 'phy_link' to -1. This causes the link
state machine to incorrectly interpret the state as a link change event,
resulting in spurious "Link is down" messages being logged when the
interface is brought back up.
Preserve the phy_link state across interface toggles to avoid treating
the -1 sentinel value as a legitimate link state transition.
Fixes: 88131a812b16 ("amd-xgbe: Perform phy connect/disconnect at dev open/stop") Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com> Link: https://patch.msgid.link/20251010065142.1189310-1-Raju.Rangoju@amd.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Similarly to ipv4 tunnel, ipv6 version updates dev->needed_headroom, too.
While ipv4 tunnel headroom adjustment growth was limited in
commit 5ae1e9922bbd ("net: ip_tunnel: prevent perpetual headroom growth"),
ipv6 tunnel yet increases the headroom without any ceiling.
Reflect ipv4 tunnel headroom adjustment limit on ipv6 version.
Credits to Francesco Ruggeri, who was originally debugging this issue
and wrote local Arista-specific patch and a reproducer.
After resume from S4 (hibernate), RTL8168H/RTL8111H truncates incoming
packets. Packet captures show messages like "IP truncated-ip - 146 bytes
missing!".
The issue is caused by RxConfig not being properly re-initialized after
resume. Re-initializing the RxConfig register before the chip
re-initialization sequence avoids the truncation and restores correct
packet reception.
This follows the same pattern as commit ef9da46ddef0 ("r8169: fix data
corruption issue on RTL8402").
Fixes: 6e1d0b898818 ("r8169:add support for RTL8168H and RTL8107E") Signed-off-by: Linmao Li <lilinmao@kylinos.cn> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://patch.msgid.link/20251009122549.3955845-1-lilinmao@kylinos.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This sysctl is not per interface; it's global per netns.
Fixes: 292ecd9f5a94 ("doc: move seg6_flowlabel to seg6-sysctl.rst") Reported-by: Philippe Guibert <philippe.guibert@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 227619c3ff7c ("can: m_can: move runtime PM enable/disable to
m_can_platform") moved the PM runtime enable from the m_can core
driver into the m_can_platform.
That patch forgot to move the pm_runtime_disable() to
m_can_plat_remove(), so that unloading the m_can_platform driver
causes an "Unbalanced pm_runtime_enable!" error message.
Add the missing pm_runtime_disable() to m_can_plat_remove() to fix the
problem.
Cc: Patrik Flykt <patrik.flykt@linux.intel.com> Fixes: 227619c3ff7c ("can: m_can: move runtime PM enable/disable to m_can_platform") Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com> Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-1-682b49b49d9a@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 168316db3583("dax: assert that i_rwsem is held
exclusive for writes") added lock assertions to ensure proper
locking in DAX operations. However, these assertions trigger
false-positive lockdep warnings since read lock is unnecessary
on read-only filesystems(e.g., erofs).
This patch skips the read lock assertion for read-only filesystems,
eliminating the spurious warnings while maintaining the integrity
checks for writable filesystems.
Fixes: 168316db3583 ("dax: assert that i_rwsem is held exclusive for writes") Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com> Reviewed-by: Friendy Su <friendy.su@sony.com> Reviewed-by: Daniel Palmer <daniel.palmer@sony.com> Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sticky fingers quirk (MT_QUIRK_STICKY_FINGERS) was only considering
the case when slots were not released during the last report.
This can be problematic if the firmware forgets to release a finger
while others are still present.
This was observed on the Synaptics DLL0945 touchpad found on the Dell
XPS 9310 and the Dell Inspiron 5406.
Fixes: 4f4001bc76fd ("HID: multitouch: fix rare Win 8 cases when the touch up event gets missing") Cc: stable@vger.kernel.org Signed-off-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After an bind/unbind cycle, the rndis->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
After an bind/unbind cycle, the ncm->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
After an bind/unbind cycle, the acm->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
After an bind/unbind cycle, the ecm->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
Gadget function drivers often have goto-based error handling in their
bind paths, which can be bug-prone. Refactoring these paths to use
__free() scope-based cleanup is desirable, but currently blocked.
The blocker is that usb_ep_free_request(ep, req) requires two
parameters, while the __free() mechanism can only pass a pointer to the
request itself.
Store an endpoint pointer in the struct usb_request. The pointer is
populated centrally in usb_ep_alloc_request() on every successful
allocation, making the request object self-contained.
If streamon/streamoff calls are imbalanced, such as when exiting an
application with Ctrl+C when streaming, the m2m usage_count will never
reach zero and the ISI channel won't be freed. Besides from that, if the
input line width is more than 2K, it will trigger a WARN_ON():
Address this issue by moving the streaming preparation and cleanup to
the vb2 .prepare_streaming() and .unprepare_streaming() operations. This
also simplifies the driver by allowing direct usage of the
v4l2_m2m_ioctl_streamon() and v4l2_m2m_ioctl_streamoff() helpers.
Condition guards are found to be redundant, as the call flow is properly
managed now, as also observed in the Exynos5433 DECON driver. Since
state checking is no longer necessary, remove it.
This also fixes an issue which prevented decon_commit() from
decon_atomic_enable() due to an incorrect state change setting.
The DECON channels are not cleared properly as the windows aren't
shadow protected. When accompanied with an IOMMU, it pagefaults, and
the kernel panics.
Implement shadow protect/unprotect, along with a standalone update,
for channel clearing to properly take effect.
Since the PDC resides out of the GPU subsystem and cannot be reset in
case it enters bad state, utmost care must be taken to trigger the PDC
wake/sleep routines in the correct order.
The PDC wake sequence can be exercised only after a PDC sleep sequence.
Additionally, GMU firmware should initialize a few registers before the
KMD can trigger a PDC sleep sequence. So PDC sleep can't be done if the
GMU firmware has not initialized. Track these dependencies using a new
status variable and trigger PDC sleep/wake sequences appropriately.
Cc: stable@vger.kernel.org Fixes: 4b565ca5a2cb ("drm/msm: Add A6XX device support") Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673362/ Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
[ omitted A7XX GPU logic and newer struct fields ] Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory barriers help ensure instruction ordering, NOT time and order
of actual write arrival at other observers (e.g. memory-mapped IP).
On architectures employing weak memory ordering, the latter can be a
giant pain point, and it has been as part of this driver.
Moreover, the gpu_/gmu_ accessors already use non-relaxed versions of
readl/writel, which include r/w (respectively) barriers.
Replace the barriers with a readback (or drop altogether where possible)
that ensures the previous writes have exited the write buffer (as the CPU
must flush the write to the register it's trying to read back).
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/600869/ Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com> Signed-off-by: Rob Clark <robdclark@chromium.org>
Stable-dep-of: f248d5d5159a ("drm/msm/a6xx: Fix PDC sleep sequence") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ready event list of an epoll object is protected by read-write
semaphore:
- The consumer (waiter) acquires the write lock and takes items.
- the producer (waker) takes the read lock and adds items.
The point of this design is enabling epoll to scale well with large number
of producers, as multiple producers can hold the read lock at the same
time.
Unfortunately, this implementation may cause scheduling priority inversion
problem. Suppose the consumer has higher scheduling priority than the
producer. The consumer needs to acquire the write lock, but may be blocked
by the producer holding the read lock. Since read-write semaphore does not
support priority-boosting for the readers (even with CONFIG_PREEMPT_RT=y),
we have a case of priority inversion: a higher priority consumer is blocked
by a lower priority producer. This problem was reported in [1].
Furthermore, this could also cause stall problem, as described in [2].
Fix this problem by replacing rwlock with spinlock.
This reduces the event bandwidth, as the producers now have to contend with
each other for the spinlock. According to the benchmark from
https://github.com/rouming/test-tools/blob/master/stress-epoll.c:
On 12 x86 CPUs:
Before After Diff
threads events/ms events/ms
8 7162 4956 -31%
16 8733 5383 -38%
32 7968 5572 -30%
64 10652 5739 -46%
128 11236 5931 -47%
On 4 riscv CPUs:
Before After Diff
threads events/ms events/ms
8 2958 2833 -4%
16 3323 3097 -7%
32 3451 3240 -6%
64 3554 3178 -11%
128 3601 3235 -10%
Although the numbers look bad, it should be noted that this benchmark
creates multiple threads who do nothing except constantly generating new
epoll events, thus contention on the spinlock is high. For real workload,
the event rate is likely much lower, and the performance drop is not as
bad.
Using another benchmark (perf bench epoll wait) where spinlock contention
is lower, improvement is even observed on x86:
On 12 x86 CPUs:
Before: Averaged 110279 operations/sec (+- 1.09%), total secs = 8
After: Averaged 114577 operations/sec (+- 2.25%), total secs = 8
On 4 riscv CPUs:
Before: Averaged 175767 operations/sec (+- 0.62%), total secs = 8
After: Averaged 167396 operations/sec (+- 0.23%), total secs = 8
In conclusion, no one is likely to be upset over this change. After all,
spinlock was used originally for years, and the commit which converted to
rwlock didn't mention a real workload, just that the benchmark numbers are
nice.
This patch is not exactly the revert of commit a218cc491420 ("epoll: use
rwlock in order to reduce ep_poll_callback() contention"), because git
revert conflicts in some places which are not obvious on the resolution.
This patch is intended to be backported, therefore go with the obvious
approach:
- Replace rwlock_t with spinlock_t one to one
- Delete list_add_tail_lockless() and chain_epi_lockless(). These were
introduced to allow producers to concurrently add items to the list.
But now that spinlock no longer allows producers to touch the event
list concurrently, these two functions are not necessary anymore.
Fixes: a218cc491420 ("epoll: use rwlock in order to reduce ep_poll_callback() contention") Signed-off-by: Nam Cao <namcao@linutronix.de> Link: https://lore.kernel.org/ec92458ea357ec503c737ead0f10b2c6e4c37d47.1752581388.git.namcao@linutronix.de Tested-by: K Prateek Nayak <kprateek.nayak@amd.com> Cc: stable@vger.kernel.org Reported-by: Frederic Weisbecker <frederic@kernel.org> Closes: https://lore.kernel.org/linux-rt-users/20210825132754.GA895675@lothringen/ [1] Reported-by: Valentin Schneider <vschneid@redhat.com> Closes: https://lore.kernel.org/linux-rt-users/xhsmhttqvnall.mognet@vschneid.remote.csb/ [2] Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 443f1a042233 ("lift the calls of ep_send_events_proc()
into the callers"), ep_scan_ready_list() has been removed.
But there are still several in comments. All of them should
be replaced with other caller functions.
Signed-off-by: Huang Xiaojia <huangxiaojia2@huawei.com> Link: https://lore.kernel.org/r/20240206014353.4191262-1-huangxiaojia2@huawei.com Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Christian Brauner <brauner@kernel.org>
Stable-dep-of: 0c43094f8cc9 ("eventpoll: Replace rwlock with spinlock") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If cppc_get_transition_latency() returns CPUFREQ_ETERNAL to indicate a
failure to retrieve the transition latency value from the platform
firmware, the CPPC cpufreq driver will use that value (converted to
microseconds) as the policy transition delay, but it is way too large
for any practical use.
Address this by making the driver use the cpufreq's default
transition latency value (in microseconds) as the transition delay
if CPUFREQ_ETERNAL is returned by cppc_get_transition_latency().
Fixes: d4f3388afd48 ("cpufreq / CPPC: Set platform specific transition_delay_us") Cc: 5.19+ <stable@vger.kernel.org> # 5.19 Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org> Reviewed-by: Jie Zhan <zhanjie9@hisilicon.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Qais Yousef <qyousef@layalina.io>
[ added CPUFREQ_DEFAULT_TRANSITION_LATENCY_NS definition to include/linux/cpufreq.h ] Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
Not all renoir hardware supports secure display. If the TA is present
but the feature isn't supported it will fail to load or send commands.
This shows ERR messages to the user that make it seems like there is
a problem.
[How]
Check the resp_status of the context to see if there was an error
before trying to send any secure display commands.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/1415 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Adrian Yip <adrian.ytw@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The atomic variable vm_fault_info_updated is used to synchronize access to
adev->gmc.vm_fault_info between the interrupt handler and
get_vm_fault_info().
The default atomic functions like atomic_set() and atomic_read() do not
provide memory barriers. This allows for CPU instruction reordering,
meaning the memory accesses to vm_fault_info and the vm_fault_info_updated
flag are not guaranteed to occur in the intended order. This creates a
race condition that can lead to inconsistent or stale data being used.
The previous implementation, which used an explicit mb(), was incomplete
and inefficient. It failed to account for all potential CPU reorderings,
such as the access of vm_fault_info being reordered before the atomic_read
of the flag. This approach is also more verbose and less performant than
using the proper atomic functions with acquire/release semantics.
Fix this by switching to atomic_set_release() and atomic_read_acquire().
These functions provide the necessary acquire and release semantics,
which act as memory barriers to ensure the correct order of operations.
It is also more efficient and idiomatic than using explicit full memory
barriers.
Fixes: b97dfa27ef3a ("drm/amdgpu: save vm fault information for amdkfd") Cc: stable@vger.kernel.org Signed-off-by: Gui-Dong Han <hanguidong02@gmail.com> Signed-off-by: Felix Kuehling <felix.kuehling@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding dependencies with drm_sched_job_add_dependency(), that
function consumes the fence reference both on success and failure, so in
the latter case the dma_fence_put() on the error path (xarray failed to
expand) is a double free.
Interestingly this bug appears to have been present ever since
commit ebd5f74255b9 ("drm/sched: Add dependency tracking"), since the code
back then looked like this:
drm_sched_job_add_implicit_dependencies():
...
for (i = 0; i < fence_count; i++) {
ret = drm_sched_job_add_dependency(job, fences[i]);
if (ret)
break;
}
for (; i < fence_count; i++)
dma_fence_put(fences[i]);
Which means for the failing 'i' the dma_fence_put was already a double
free. Possibly there were no users at that time, or the test cases were
insufficient to hit it.
The bug was then only noticed and fixed after
commit 9c2ba265352a ("drm/scheduler: use new iterator in drm_sched_job_add_implicit_dependencies v2")
landed, with its fixup of
commit 4eaf02d6076c ("drm/scheduler: fix drm_sched_job_add_implicit_dependencies").
At that point it was a slightly different flavour of a double free, which
commit 963d0b356935 ("drm/scheduler: fix drm_sched_job_add_implicit_dependencies harder")
noticed and attempted to fix.
But it only moved the double free from happening inside the
drm_sched_job_add_dependency(), when releasing the reference not yet
obtained, to the caller, when releasing the reference already released by
the former in the failure case.
As such it is not easy to identify the right target for the fixes tag so
lets keep it simple and just continue the chain.
While fixing we also improve the comment and explain the reason for taking
the reference and not dropping it.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com> Fixes: 963d0b356935 ("drm/scheduler: fix drm_sched_job_add_implicit_dependencies harder") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/dri-devel/aNFbXq8OeYl3QSdm@stanley.mountain/ Cc: Christian König <christian.koenig@amd.com> Cc: Rob Clark <robdclark@chromium.org> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Matthew Brost <matthew.brost@intel.com> Cc: Danilo Krummrich <dakr@kernel.org> Cc: Philipp Stanner <phasta@kernel.org> Cc: Christian König <ckoenig.leichtzumerken@gmail.com> Cc: dri-devel@lists.freedesktop.org Cc: stable@vger.kernel.org # v5.16+ Signed-off-by: Philipp Stanner <phasta@kernel.org> Link: https://lore.kernel.org/r/20251015084015.6273-1-tvrtko.ursulin@igalia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue was found by Runcheng Lu when develop HSCanT USB to CAN FD
converter[1]. The original developers may have only 3 interfaces
device to test so they write 3 here and wait for future change.
During the HSCanT development, we actually used 4 interfaces, so the
limitation of 3 is not enough now. But just increase one is not
future-proofed. Since the channel index type in gs_host_frame is u8,
just make canch[] become a flexible array with a u8 index, so it
naturally constraint by U8_MAX and avoid statically allocate 256
pointer for every gs_usb device.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices") Reported-by: Runcheng Lu <runcheng.lu@hpmicro.com> Cc: stable@vger.kernel.org Reviewed-by: Vincent Mailhol <mailhol@kernel.org> Signed-off-by: Celeste Liu <uwu@coelacanthus.name> Link: https://patch.msgid.link/20250930-gs-usb-max-if-v5-1-863330bf6666@coelacanthus.name Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gs_usb driver supports USB devices with more than 1 CAN channel.
In old kernel before 3.15, it uses net_device->dev_id to distinguish
different channel in userspace, which was done in commit acff76fa45b4 ("can: gs_usb: gs_make_candev(): set netdev->dev_id").
But since 3.15, the correct way is populating net_device->dev_port.
And according to documentation, if network device support multiple
interface, lack of net_device->dev_port SHALL be treated as a bug.
Currently, when building a free space tree at populate_free_space_tree(),
if we are not using the block group tree feature, we always expect to find
block group items (either extent items or a block group item with key type
BTRFS_BLOCK_GROUP_ITEM_KEY) when we search the extent tree with
btrfs_search_slot_for_read(), so we assert that we found an item. However
this expectation is wrong since we can have a new block group created in
the current transaction which is still empty and for which we still have
not added the block group's item to the extent tree, in which case we do
not have any items in the extent tree associated to the block group.
The insertion of a new block group's block group item in the extent tree
happens at btrfs_create_pending_block_groups() when it calls the helper
insert_block_group_item(). This typically is done when a transaction
handle is released, committed or when running delayed refs (either as
part of a transaction commit or when serving tickets for space reservation
if we are low on free space).
So remove the assertion at populate_free_space_tree() even when the block
group tree feature is not enabled and update the comment to mention this
case.
Syzbot reported this with the following stack trace:
The intent of btrfs_readahead_expand() was to expand to the length of
the current compressed extent being read. However, "ram_bytes" is *not*
that, in the case where a single physical compressed extent is used for
multiple file extents.
Consider this case with a large compressed extent C and then later two
non-compressed extents N1 and N2 written over C, leaving C1 and C2
pointing to offset/len pairs of C:
[ C ]
[ N1 ][ C1 ][ N2 ][ C2 ]
In such a case, ram_bytes for both C1 and C2 is the full uncompressed
length of C. So starting readahead in C1 will expand the readahead past
the end of C1, past N2, and into C2. This will then expand readahead
again, to C2_start + ram_bytes, way past EOF. First of all, this is
totally undesirable, we don't want to read the whole file in arbitrary
chunks of the large underlying extent if it happens to exist. Secondly,
it results in zeroing the range past the end of C2 up to ram_bytes. This
is particularly unpleasant with fs-verity as it can zero and set
uptodate pages in the verity virtual space past EOF. This incorrect
readahead behavior can lead to verity verification errors, if we iterate
in a way that happens to do the wrong readahead.
Fix this by using em->len for readahead expansion, not em->ram_bytes,
resulting in the expected behavior of stopping readahead at the extent
boundary.
Reported-by: Max Chernoff <git@maxchernoff.ca> Link: https://bugzilla.redhat.com/show_bug.cgi?id=2399898 Fixes: 9e9ff875e417 ("btrfs: use readahead_expand() on compressed extents") CC: stable@vger.kernel.org # 6.17 Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Boris Burkov <boris@bur.io> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When starting relocation, at reloc_chunk_start(), if we happen to find
the flag BTRFS_FS_RELOC_RUNNING is already set we return an error
(-EINPROGRESS) to the callers, however the callers call reloc_chunk_end()
which will clear the flag BTRFS_FS_RELOC_RUNNING, which is wrong since
relocation was started by another task and still running.
Finding the BTRFS_FS_RELOC_RUNNING flag already set is an unexpected
scenario, but still our current behaviour is not correct.
Fix this by never calling reloc_chunk_end() if reloc_chunk_start() has
returned an error, which is what logically makes sense, since the general
widespread pattern is to have end functions called only if the counterpart
start functions succeeded. This requires changing reloc_chunk_start() to
clear BTRFS_FS_RELOC_RUNNING if there's a pending cancel request.
Fixes: 907d2710d727 ("btrfs: add cancellable chunk relocation support") CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Boris Burkov <boris@bur.io> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Investigation revealed that the inode has both flags set:
DEBUG: inode 15 - flag=1, i_inline_off=164, has_inline=1, extents_flag=1
This is an invalid combination since an inode should have either:
- INLINE_DATA: data stored directly in the inode
- EXTENTS: data stored in extent-mapped blocks
Having both flags causes ext4_has_inline_data() to return true, skipping
extent tree validation in __ext4_iget(). The unvalidated out-of-order
extents then trigger a BUG_ON in ext4_es_cache_extent() due to integer
underflow when calculating hole sizes.
Fix this by detecting this invalid flag combination early in ext4_iget()
and rejecting the corrupted inode.
projects / thirdparty / kernel / stable.git / log
