The driver changes the stream name of DAC and ADC to avoid the issue of
widget with prefixed name. When the machine adds prefixed name for codec,
the stream name of DAI may not find the widgets.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver has two issues when machine add prefix name for codec.
(1)The stream name of DAI can't find the AIF widgets.
(2)The drivr can enable/disalbe the MICBIAS and SAR widgets.
The patch will fix these issues caused by prefixed name added.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On HDaudio platforms, if playback is started when capture is working,
there is no audible output.
This can be root-caused to the use of the rx|tx_mask to store an HDaudio
stream tag.
If capture is stared before playback, rx_mask would be non-zero on HDaudio
platform, then the channel number of playback, which is in the same codec
dai with the capture, would be changed by soc_pcm_codec_params_fixup based
on the tx_mask at first, then overwritten by this function based on rx_mask
at last.
According to the author of tx|rx_mask, tx_mask is for playback and rx_mask
is for capture. And stream direction is checked at all other references of
tx|rx_mask in ASoC, so here should be an error. This patch checks stream
direction for tx|rx_mask for fixup function.
This issue would affect not only HDaudio+ASoC, but also I2S codecs if the
channel number based on rx_mask is not equal to the one for tx_mask. It could
be rarely reproduecd because most drivers in kernel set the same channel number
to tx|rx_mask or rx_mask is zero.
Tested on all platforms using stream_tag & HDaudio and intel I2S platforms.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using the S/PDIF DAI, there is no requirement to call
snd_soc_dai_set_fmt() as there is no DAI format definition that defines
S/PDIF. In any case, S/PDIF does not have separate clocks, this is
embedded into the data stream.
Consequently, when attempting to use TDA998x in S/PDIF mode, the attempt
to configure TDA998x via the hw_params callback fails as the
hdmi_codec_daifmt is left initialised to zero.
Since the S/PDIF DAI will only be used by S/PDIF, prepare the
hdmi_codec_daifmt structure for this format.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Jyri Sarha <jsarha@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since moving the message buffers off the stack, the dynamically
allocated get-prop-descriptor request buffer is incorrectly sized due to
using the pointer rather than request-struct size when creating the
operation.
Fortunately, the pointer size is always larger than this one-byte
request, but this could still cause trouble on the remote end due to the
unexpected message size.
Fixes: 9d15134d067e ("greybus: power_supply: rework get descriptors") Cc: stable <stable@vger.kernel.org> # 4.9 Cc: Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building lib/ubsan.c with gcc-9 results in a ton of nasty warnings like
this one:
lib/ubsan.c warning: conflicting types for built-in function
‘__ubsan_handle_negate_overflow’; expected ‘void(void *, void *)’ [-Wbuiltin-declaration-mismatch]
The kernel's declarations of __ubsan_handle_*() often uses 'unsigned
long' types in parameters while GCC these parameters as 'void *' types,
hence the mismatch.
Fix this by using 'void *' to match GCC's declarations.
When the lldd is processing the complete sas task in interrupt and set the
task stat as SAS_TASK_STATE_DONE, the smp timeout timer is able to be
triggered at the same time. And smp_task_timedout() will complete the task
wheter the SAS_TASK_STATE_DONE is set or not. Then the sas task may freed
before lldd end the interrupt process. Thus a use-after-free will happen.
Fix this by calling the complete() only when SAS_TASK_STATE_DONE is not
set. And remove the check of the return value of the del_timer(). Once the
LLDD sets DONE, it must call task->done(), which will call
smp_task_done()->complete() and the task will be completed and freed
correctly.
Reported-by: chenxiang <chenxiang66@hisilicon.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Johannes Thumshirn <jthumshirn@suse.de> CC: Ewan Milne <emilne@redhat.com> CC: Christoph Hellwig <hch@lst.de> CC: Tomas Henzl <thenzl@redhat.com> CC: Dan Williams <dan.j.williams@intel.com> CC: Hannes Reinecke <hare@suse.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Guenter Roeck <linux@roeck-us.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following commits:
commit f6dd927f34d6 ("[media] media: ov7670: calculate framerate properly for ov7675")
commit 04ee6d92047e ("[media] media: ov7670: add possibility to bypass pll for ov7675")
introduced the ability to bypass PLL multiplier and use input clock (xvclk)
as pixel clock output frequency for ov7675 sensor.
PLL is bypassed using register DBLV[7:6], according to ov7670 and ov7675
sensor manuals. Macros used to set DBLV register seem wrong in the
driver, as their values do not match what reported in the datasheet.
Fix by changing DBLV_* macros to use bits [7:6] and set bits [3:0] to
default 0x0a reserved value (according to datasheets).
While at there, remove a write to DBLV register in
"ov7675_set_framerate()" that over-writes the previous one to the same
register that takes "info->pll_bypass" flag into account instead of setting PLL
multiplier to 4x unconditionally.
And, while at there, since "info->pll_bypass" is only used in
set/get_framerate() functions used by ov7675 only, it is not necessary
to check for the device id at probe time to make sure that when using
ov7670 "info->pll_bypass" is set to false.
Since commit 648e921888ad ("clk: x86: Stop marking clocks as
CLK_IS_CRITICAL"), the pmc_plt_clocks of the Bay Trail SoC are
unconditionally gated off. Unfortunately this will break systems where these
clocks are used for external purposes beyond the kernel's knowledge. Fix it
by implementing a system specific quirk to mark the necessary pmc_plt_clks as
critical.
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL") Signed-off-by: David Müller <dave.mueller@gmx.ch> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
c7d606f560e4 ("x86/mce: Improve error message when kernel cannot recover")
a case was added for a machine check caused by a DATA access to poison
memory from the kernel. A case should have been added also for an
uncorrectable error during an instruction fetch in the kernel.
Add that extra case so the error message now reads:
mce: [Hardware Error]: Machine check: Instruction fetch error in kernel
Fixes: c7d606f560e4 ("x86/mce: Improve error message when kernel cannot recover") Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Pu Wen <puwen@hygon.cn> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190225205940.15226-1-tony.luck@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When doing top-down search the low_limit is not PAGE_SIZE but rather
max(PAGE_SIZE, mmap_min_addr). This handle cases in which mmap_min_addr >
PAGE_SIZE.
Fixes: fba2369e6ceb ("mm: use vm_unmapped_area() on powerpc architecture") Reviewed-by: Laurent Dufour <ldufour@linux.vnet.ibm.com> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the SECURITY_FS_USE_MNTPOINT case we never want to allow relabeling
files/directories, so we should never set the SBLABEL_MNT flag. The
'special handling' in selinux_is_sblabel_mnt() is only intended for when
the behavior is set to SECURITY_FS_USE_GENFS.
While there, make the logic in selinux_is_sblabel_mnt() more explicit
and add a BUILD_BUG_ON() to make sure that introducing a new
SECURITY_FS_USE_* forces a review of the logic.
Fixes: d5f3a5f6e7e7 ("selinux: add security in-core xattr support for pstore and debugfs") Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Reviewed-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to turn regulators on and off when switching brightness, and
that may block, therefore we have to set stmfts_brightness_set() as
LED's brightness_set_blocking() method.
Fixes: 78bcac7b2ae1 ("Input: add support for the STMicroelectronics FingerTip touchscreen") Acked-by: Andi Shyti <andi@etezian.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SNVS IRQ is requested before necessary driver data initialized,
if there is a pending IRQ during driver probe phase, kernel
NULL pointer panic will occur in IRQ handler. To avoid such
scenario, just initialize necessary driver data before enabling
IRQ. This patch is inspired by NXP's internal kernel tree.
The open-coded variant missed destroy of SELinux created QP, reuse already
existing ib_detroy_qp() call and use this opportunity to clean
ib_create_qp() from double prints and unclear exit paths.
Reported-by: Parav Pandit <parav@mellanox.com> Fixes: d291f1a65232 ("IB/core: Enforce PKey security on QPs") Signed-off-by: Yuval Avnery <yuvalav@mellanox.com> Reviewed-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the MAD agents isn't allowed to manage the subnet, or fails to register
for the LSM notifier, the security context is leaked. Free the context in
these cases.
Fixes: 47a2b338fe63 ("IB/core: Enforce security on management datagrams") Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Reviewed-by: Parav Pandit <parav@mellanox.com> Reported-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lsb calculation is not masking the correct bits from the user input.
Subtract 1 from (1 << offset) to correctly set up the mask to be applied
to user input.
The lsb register stores its value starting at the bit 7 position.
adt7316_store_DAC() currently assumes the value is at the other end of the
register. Shift the lsb value before storing it in a new variable lsb_reg,
and write this variable to the lsb register.
Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver") Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The calculation of the current dac value is using the wrong bits of the
dac lsb register. Create two macros to shift the lsb register value into
lsb position, depending on whether the dac is 10 or 12 bit. Initialize
data to 0 so, with an 8 bit dac, the msb register value can be bitwise
ORed with data.
Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver") Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With adt7516/7/9, internal vref is available for dacs a and b, dacs c and
d, or all dacs. The driver doesn't currently support internal vref for all
dacs. Change the else if to an if so both bits are checked rather than
just one or the other.
Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com> Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Badly-designed systems might have (for example) active-high wake pins
that default to high (e.g., because of external pull ups) until they
have an active firmware which starts driving it low. This can cause an
interrupt storm in the time between request_irq() and disable_irq().
We don't support shared interrupts here, so let's just pre-configure the
interrupt to avoid auto-enabling it.
Fixes: fd913ef7ce61 ("Bluetooth: btusb: Add out-of-band wakeup support") Fixes: 5364a0b4f4be ("arm64: dts: rockchip: move QCA6174A wakeup pin into its USB node") Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new amd_hw_cache_event_ids_f17h assignment structure set
for AMD families 17h and above, since a lot has changed. Specifically:
L1 Data Cache
The data cache access counter remains the same on Family 17h.
For DC misses, PMCx041's definition changes with Family 17h,
so instead we use the L2 cache accesses from L1 data cache
misses counter (PMCx060,umask=0xc8).
For DC hardware prefetch events, Family 17h breaks compatibility
for PMCx067 "Data Prefetcher", so instead, we use PMCx05a "Hardware
Prefetch DC Fills."
L1 Instruction Cache
PMCs 0x80 and 0x81 (32-byte IC fetches and misses) are backward
compatible on Family 17h.
For prefetches, we remove the erroneous PMCx04B assignment which
counts how many software data cache prefetch load instructions were
dispatched.
LL - Last Level Cache
Removing PMCs 7D, 7E, and 7F assignments, as they do not exist
on Family 17h, where the last level cache is L3. L3 counters
can be accessed using the existing AMD Uncore driver.
Data TLB
On Intel machines, data TLB accesses ("dTLB-loads") are assigned
to counters that count load/store instructions retired. This
is inconsistent with instruction TLB accesses, where Intel
implementations report iTLB misses that hit in the STLB.
Ideally, dTLB-loads would count higher level dTLB misses that hit
in lower level TLBs, and dTLB-load-misses would report those
that also missed in those lower-level TLBs, therefore causing
a page table walk. That would be consistent with instruction
TLB operation, remove the redundancy between dTLB-loads and
L1-dcache-loads, and prevent perf from producing artificially
low percentage ratios, i.e. the "0.01%" below:
42,550,869 L1-dcache-loads
41,591,860 dTLB-loads
4,802 dTLB-load-misses # 0.01% of all dTLB cache hits
7,283,682 L1-dcache-stores
7,912,392 dTLB-stores
310 dTLB-store-misses
On AMD Families prior to 17h, the "Data Cache Accesses" counter is
used, which is slightly better than load/store instructions retired,
but still counts in terms of individual load/store operations
instead of TLB operations.
So, for AMD Families 17h and higher, this patch assigns "dTLB-loads"
to a counter for L1 dTLB misses that hit in the L2 dTLB, and
"dTLB-load-misses" to a counter for L1 DTLB misses that caused
L2 DTLB misses and therefore also caused page table walks. This
results in a much more accurate view of data TLB performance:
60,961,781 L1-dcache-loads
4,601 dTLB-loads
963 dTLB-load-misses # 20.93% of all dTLB cache hits
Note that for all AMD families, data loads and stores are combined
in a single accesses counter, so no 'L1-dcache-stores' are reported
separately, and stores are counted with loads in 'L1-dcache-loads'.
Also note that the "% of all dTLB cache hits" string is misleading
because (a) "dTLB cache": although TLBs can be considered caches for
page tables, in this context, it can be misinterpreted as data cache
hits because the figures are similar (at least on Intel), and (b) not
all those loads (technically accesses) technically "hit" at that
hardware level. "% of all dTLB accesses" would be more clear/accurate.
Instruction TLB
On Intel machines, 'iTLB-loads' measure iTLB misses that hit in the
STLB, and 'iTLB-load-misses' measure iTLB misses that also missed in
the STLB and completed a page table walk.
For AMD Family 17h and above, for 'iTLB-loads' we replace the
erroneous instruction cache fetches counter with PMCx084
"L1 ITLB Miss, L2 ITLB Hit".
For 'iTLB-load-misses' we still use PMCx085 "L1 ITLB Miss,
L2 ITLB Miss", but set a 0xff umask because without it the event
does not get counted.
Branch Predictor (BPU)
PMCs 0xc2 and 0xc3 continue to be valid across all AMD Families.
Node Level Events
Family 17h does not have a PMCx0e9 counter, and corresponding counters
have not been made available publicly, so for now, we mark them as
unsupported for Families 17h and above.
Reference:
"Open-Source Register Reference For AMD Family 17h Processors Models 00h-2Fh"
Released 7/17/2018, Publication #56255, Revision 3.03:
https://www.amd.com/system/files/TechDocs/56255_OSRR.pdf
[ mingo: tidied up the line breaks. ] Signed-off-by: Kim Phillips <kim.phillips@amd.com> Cc: <stable@vger.kernel.org> # v4.9+ Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Martin Liška <mliska@suse.cz> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Pu Wen <puwen@hygon.cn> Cc: Stephane Eranian <eranian@google.com> Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Lendacky <Thomas.Lendacky@amd.com> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: linux-kernel@vger.kernel.org Cc: linux-perf-users@vger.kernel.org Fixes: e40ed1542dd7 ("perf/x86: Add perf support for AMD family-17h processors") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If xace hardware reports a bad version number, the error handling code
in ace_setup() calls put_disk(), followed by queue cleanup. However, since
the disk data structure has the queue pointer set, put_disk() also
cleans and releases the queue. This results in blk_cleanup_queue()
accessing an already released data structure, which in turn may result
in a crash such as the following.
Fix the problem by setting the disk queue pointer to NULL before calling
put_disk(). A more comprehensive fix might be to rearrange the code
to check the hardware version before initializing data structures,
but I don't know if this would have undesirable side effects, and
it would increase the complexity of backporting the fix to older kernels.
Fixes: 74489a91dd43a ("Add support for Xilinx SystemACE CompactFlash interface") Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Many of the sh CPU-types have their own plat_irq_setup() and
arch_init_clk_ops() functions, so these same (empty) functions in
arch/sh/boards/of-generic.c are not needed and cause build errors.
If there is some case where these empty functions are needed, they can
be retained by marking them as "__weak" while at the same time making
builds that do not need them succeed.
Fixes these build errors:
arch/sh/boards/of-generic.o: In function `plat_irq_setup':
(.init.text+0x134): multiple definition of `plat_irq_setup'
arch/sh/kernel/cpu/sh2/setup-sh7619.o:(.init.text+0x30): first defined here
arch/sh/boards/of-generic.o: In function `arch_init_clk_ops':
(.init.text+0x118): multiple definition of `arch_init_clk_ops'
arch/sh/kernel/cpu/sh2/clock-sh7619.o:(.init.text+0x0): first defined here
Link: http://lkml.kernel.org/r/9ee4e0c5-f100-86a2-bd4d-1d3287ceab31@infradead.org Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kbuild test robot <lkp@intel.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Rich Felker <dalias@libc.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When mknod is used to create a block special file in hugetlbfs, it will
allocate an inode and kmalloc a 'struct resv_map' via resv_map_alloc().
inode->i_mapping->private_data will point the newly allocated resv_map.
However, when the device special file is opened bd_acquire() will set
inode->i_mapping to bd_inode->i_mapping. Thus the pointer to the
allocated resv_map is lost and the structure is leaked.
Programs to reproduce:
mount -t hugetlbfs nodev hugetlbfs
mknod hugetlbfs/dev b 0 0
exec 30<> hugetlbfs/dev
umount hugetlbfs/
resv_map structures are only needed for inodes which can have associated
page allocations. To fix the leak, only allocate resv_map for those
inodes which could possibly be associated with page allocations.
Link: http://lkml.kernel.org/r/20190401213101.16476-1-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Reported-by: Yufen Yu <yuyufen@huawei.com> Suggested-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 2d4f567103ff ("KVM: PPC: Introduce kvm_tmp framework") adds
kvm_tmp[] into the .bss section and then free the rest of unused spaces
back to the page allocator.
With DEBUG_PAGEALLOC=y, it will unmap those pages from kernel. As the
result, kmemleak scan will trigger a panic when it scans the .bss
section with unmapped pages.
This patch creates dedicated kmemleak objects for the .data, .bss and
potentially .data..ro_after_init sections to allow partial freeing via
the kmemleak_free_part() in the powerpc kvm_free_tmp() function.
Link: http://lkml.kernel.org/r/20190321171917.62049-1-catalin.marinas@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Qian Cai <cai@lca.pw> Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc) Tested-by: Qian Cai <cai@lca.pw> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Avi Kivity <avi@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krcmar <rkrcmar@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The tx ring buffer map when xmit and unmap when xmit done. So in
hnae_init_ring() did not map tx ring buffer, but in hnae_fini_ring()
have a unmap operation for tx ring buffer, which is already unmapped
when xmit done, than cause this WARNING.
The hnae_alloc_buffers() is called in hnae_init_ring(),
so the hnae_free_buffers() should be in hnae_fini_ring(), not in
hnae_free_desc().
In hnae_fini_ring(), adds a check is_rx_ring() as in hnae_init_ring().
When the ring buffer is tx ring, adds a piece of code to ensure that
the tx ring is unmap.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ICMP6 neighbor solicitation messages will be discard by the Hip06
chips, because of not setting forwarding pool. Enable promisc mode
has the same problem.
This patch fix the wrong forwarding table configs for the multicast
vague matching when enable promisc mode, and add forwarding pool
for the forwarding table.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Every time the call trace is not the same, but the overwrite address
is always the same:
Unable to handle kernel paging request at virtual address 0000000200000040
The root cause is, when write the reg XGMAC_MAC_TX_LF_RF_CONTROL_REG,
didn't use the io_base offset.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the HNS driver loaded, always have an error print:
"netif_napi_add() called with weight 256"
This is because the kernel checks the NAPI polling weights
requested by drivers and it prints an error message if a driver
requests a weight bigger than 64.
So use NAPI_POLL_WEIGHT to fix it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch is trying to fix the issue due to:
[27237.844750] BUG: KASAN: use-after-free in hns_nic_net_xmit_hw+0x708/0xa18[hns_enet_drv]
After hnae_queue_xmit() in hns_nic_net_xmit_hw(), can be
interrupted by interruptions, and than call hns_nic_tx_poll_one()
to handle the new packets, and free the skb. So, when turn back to
hns_nic_net_xmit_hw(), calling skb->len will cause use-after-free.
This patch update tx ring statistics in hns_nic_tx_poll_one() to
fix the bug.
Signed-off-by: Liubin Shu <shuliubin@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the number of sub-channels offered by Hyper-V is >= the number of CPUs
in the VM, calculate the correct number of sub-channels. The current code
produces one too many.
This scenario arises only when the number of CPUs is artificially
restricted (for example, with maxcpus=<n> on the kernel boot line), because
Hyper-V normally offers a sub-channel count < number of CPUs. While the
current code doesn't break, the extra sub-channel is unbalanced across the
CPUs (for example, a total of 5 channels on a VM with 4 CPUs).
Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Long Li <longli@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Blacklist "Universal Xport" LUN. It's used for in-band storage array
management. Also add model to the rdac dh family.
Cc: Martin Wilck <mwilck@suse.com> Cc: Hannes Reinecke <hare@suse.de> Cc: NetApp RDAC team <ng-eseries-upstream-maintainers@netapp.com> Cc: Christophe Varoqui <christophe.varoqui@opensvc.com> Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: SCSI ML <linux-scsi@vger.kernel.org> Cc: DM ML <dm-devel@redhat.com> Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Reviewed-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When compiling with -Wformat, clang emits the following warnings:
drivers/vfio/pci/vfio_pci.c:1601:5: warning: format specifies type
'unsigned short' but the argument has type 'unsigned int' [-Wformat]
vendor, device, subvendor, subdevice,
^~~~~~
drivers/vfio/pci/vfio_pci.c:1601:13: warning: format specifies type
'unsigned short' but the argument has type 'unsigned int' [-Wformat]
vendor, device, subvendor, subdevice,
^~~~~~
drivers/vfio/pci/vfio_pci.c:1601:21: warning: format specifies type
'unsigned short' but the argument has type 'unsigned int' [-Wformat]
vendor, device, subvendor, subdevice,
^~~~~~~~~
drivers/vfio/pci/vfio_pci.c:1601:32: warning: format specifies type
'unsigned short' but the argument has type 'unsigned int' [-Wformat]
vendor, device, subvendor, subdevice,
^~~~~~~~~
drivers/vfio/pci/vfio_pci.c:1605:5: warning: format specifies type
'unsigned short' but the argument has type 'unsigned int' [-Wformat]
vendor, device, subvendor, subdevice,
^~~~~~
drivers/vfio/pci/vfio_pci.c:1605:13: warning: format specifies type
'unsigned short' but the argument has type 'unsigned int' [-Wformat]
vendor, device, subvendor, subdevice,
^~~~~~
drivers/vfio/pci/vfio_pci.c:1605:21: warning: format specifies type
'unsigned short' but the argument has type 'unsigned int' [-Wformat]
vendor, device, subvendor, subdevice,
^~~~~~~~~
drivers/vfio/pci/vfio_pci.c:1605:32: warning: format specifies type
'unsigned short' but the argument has type 'unsigned int' [-Wformat]
vendor, device, subvendor, subdevice,
^~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct ones for unsigned ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378 Signed-off-by: Louis Taylor <louis@kragniz.eu> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
symlink body shouldn't be freed without an RCU delay. Switch debugfs to
->destroy_inode() and use of call_rcu(); free both the inode and symlink
body in the callback. Similar to solution for bpf, only here it's even
more obvious that ->evict_inode() can be dropped.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
free the symlink body after the same RCU delay we have for freeing the
struct inode itself, so that traversal during RCU pathwalk wouldn't step
into freed memory.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is log is harmful as it can trigger multiple times per packet. Delete
it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Packets without the last descriptor set should be dropped early. If we
receive a frame larger than the DMA buffer, the HW will continue using the
next descriptor. Driver mistakes these as individual frames, and sometimes
a truncated frame (without the LD set) may look like a valid packet.
This fixes a strange issue where the system replies to 4098-byte ping
although the MTU/DMA buffer size is set to 4096, and yet at the same
time it's logging an oversized packet.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we have error bits set, the discard_frame status will get overwritten
by checksum bit checks, which might set the status back to good one.
Fix by checking the COE status only if the frame is good.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
So print full hwaddr in sysfs "bonding_slave/perm_hwaddr" as well.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Traditionally, the PF (Physical Function) which resides on vport 0 was
the E-switch manager. Since the ECPF (Embedded CPU Physical Function),
which resides on vport 0xfffe, was introduced as the E-Switch manager,
the assumption that the E-switch manager is on vport 0 is incorrect.
Since the eswitch code already uses the actual vport value, all we
need is to always set other_vport=1.
The runtime_suspend device callbacks are not supposed to save
configuration state or change the power state. Commit fb29f76cc566
("igb: Fix an issue that PME is not enabled during runtime suspend")
changed the driver to not save configuration state during runtime
suspend, however the driver callback still put the device into a
low-power state. This causes a warning in the pci pm core and results in
pci_pm_runtime_suspend not calling pci_save_state or pci_finish_runtime_suspend.
Fix this by not changing the power state either, leaving that to pci pm
core, and make the same change for suspend callback as well.
Also move a couple of defines into the appropriate header file instead
of inline in the .c file.
Fixes: fb29f76cc566 ("igb: Fix an issue that PME is not enabled during runtime suspend") Signed-off-by: Arvind Sankar <niveditas98@gmail.com> Reviewed-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.
The batadv_tt_global_free is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.
Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:
refcount_t: underflow; use-after-free.
Fixes: 7683fdc1e886 ("batman-adv: protect the local and the global trans-tables with rcu") Reported-by: Martin Weinelt <martin@linuxlounge.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.
The batadv_tt_local_remove is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.
Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:
refcount_t: underflow; use-after-free.
Fixes: ef72706a0543 ("batman-adv: protect tt_local_entry from concurrent delete events") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.
The batadv_bla_del_claim is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.
Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:
sh_rtc_read_alarm_value() returns 0xff when querying a hardware alarm
field that is not enabled. __rtc_read_alarm() validates the received
alarm values, and fills in missing fields when needed.
While 0xff is handled fine for the year, month, and day fields, and
corrected as considered being out-of-range, this is not the case for the
hour, minute, and second fields, where -1 is expected for missing
fields.
Fix this by returning -1 instead, as this value is handled fine for all
fields.
There is a race condition that could happen if hid_debug_rdesc_show()
is running while hdev is in the process of going away (device removal,
system suspend, etc) which could result in NULL pointer dereference:
BUG: unable to handle kernel paging request at 0000000783316040
CPU: 1 PID: 1512 Comm: getevent Tainted: G U O 4.19.20-quilt-2e5dc0ac-00029-gc455a447dd55 #1
RIP: 0010:hid_dump_device+0x9b/0x160
Call Trace:
hid_debug_rdesc_show+0x72/0x1d0
seq_read+0xe0/0x410
full_proxy_read+0x5f/0x90
__vfs_read+0x3a/0x170
vfs_read+0xa0/0x150
ksys_read+0x58/0xc0
__x64_sys_read+0x1a/0x20
do_syscall_64+0x55/0x110
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Grab driver_input_lock to make sure the input device exists throughout the
whole process of dumping the rdesc.
create_singlethread_workqueue may fail and return NULL. The fix checks if it is
NULL to avoid NULL pointer dereference. Also, the fix moves the call of
create_singlethread_workqueue earlier to avoid resource-release issues.
Shakeel Butt reported he has observed in production systems that the job
loader gets stuck for 10s of seconds while doing a mount operation. It
turns out that it was stuck in register_shrinker() because some
unrelated job was under memory pressure and was spending time in
shrink_slab(). Machines have a lot of shrinkers registered and jobs
under memory pressure have to traverse all of those memcg-aware
shrinkers and affect unrelated jobs which want to register their own
shrinkers.
To solve the issue, this patch simply bails out slab shrinking if it is
found that someone wants to register a shrinker in parallel. A downside
is it could cause unfair shrinking between shrinkers. However, it
should be rare and we can add compilcated logic if we find it's not
enough.
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter. This allowed
a hub to be runtime suspended at a time when the driver did not expect
it. The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:
URB 0000000031fb463e submitted while active
WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363
The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count). The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.
Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls. In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.
This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative. There's
even a warning about this in the USB power management documentation!
As it happens, this is exactly what the hub driver does. The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread. This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.
It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock. The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts. As far as I know, all
existing drivers currently do this.
Some drivers (such as the vub300 MMC driver) expect usb_string() to
return a properly NUL-terminated string, even when an error occurs.
(In fact, vub300's probe routine doesn't bother to check the return
code from usb_string().) When the driver goes on to use an
unterminated string, it leads to kernel errors such as
stack-out-of-bounds, as found by the syzkaller USB fuzzer.
An out-of-range string index argument is not at all unlikely, given
that some devices don't provide string descriptors and therefore list
0 as the value for their string indexes. This patch makes
usb_string() return a properly terminated empty string along with the
-EINVAL error code when an out-of-range index is encountered.
And since a USB string index is a single-byte value, indexes >= 256
are just as invalid as values of 0 or below.
Change the validation of number_of_packets in get_pipe to compare the
number of packets to a fixed maximum number of packets allowed, set to
be 1024. This number was chosen due to it being used by other drivers as
well, for example drivers/usb/host/uhci-q.c
Background/reason:
The get_pipe function in stub_rx.c validates the number of packets in
isochronous mode and aborts with an error if that number is too large,
in order to prevent malicious input from possibly triggering large
memory allocations. This was previously done by checking whether
pdu->u.cmd_submit.number_of_packets is bigger than the number of packets
that would be needed for pdu->u.cmd_submit.transfer_buffer_length bytes
if all except possibly the last packet had maximum length, given by
usb_endpoint_maxp(epd) * usb_endpoint_maxp_mult(epd). This leads to an
error if URBs with packets shorter than the maximum possible length are
submitted, which is allowed according to
Documentation/driver-api/usb/URB.rst and occurs for example with the
snd-usb-audio driver.
The syzkaller USB fuzzer spotted a slab-out-of-bounds bug in the
ds2490 driver. This bug is caused by improper use of the altsetting
array in the usb_interface structure (the array's entries are not
always stored in numerical order), combined with a naive assumption
that all interfaces probed by the driver will have the expected number
of altsettings.
The bug can be fixed by replacing references to the possibly
non-existent intf->altsetting[alt] entry with the guaranteed-to-exist
intf->cur_altsetting entry.
The syzkaller USB fuzzer found a general-protection-fault bug in the
yurex driver. The fault occurs when a device has been unplugged; the
driver's interrupt-URB handler logs an error message referring to the
device by name, after the device has been unregistered and its name
deallocated.
This problem is caused by the fact that the interrupt URB isn't
cancelled until the driver's private data structure is released, which
can happen long after the device is gone. The cure is to make sure
that the interrupt URB is killed before yurex_disconnect() returns;
this is exactly the sort of thing that usb_poison_urb() was meant for.
Fixed Dell AIO speaker noise.
spec->gen.auto_mute_via_amp = 1, this option was solved speaker white
noise at boot.
codec->power_save_node = 0, this option was solved speaker noise at
resume back.
[ Note: this is a further correction / addition of the previous
pin-based quirks for Dell machines; another entry for ALC236 with
the d-mic pin 0x12 and an entry for ALC295 -- tiwai ]
Fixes: b26e36b7ef36 ("ALSA: hda/realtek - add two more pin configuration sets to quirk table") Signed-off-by: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_KASAN is set, we can use relatively large amounts of kernel
stack space:
net/caif/cfctrl.c:555:1: warning: the frame size of 1600 bytes is larger than 1280 bytes [-Wframe-larger-than=]
This adds convenience wrappers around cfpkt_extr_head(), which is responsible
for most of the stack growth. With those wrapper functions, gcc apparently
starts reusing the stack slots for each instance, thus avoiding the
problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our arm64_skip_faulting_instruction() helper advances the userspace
singlestep state machine, but this is also called by the kernel BRK
handler, as used for WARN*().
Thus, if we happen to hit a WARN*() while the user singlestep state
machine is in the active-no-pending state, we'll advance to the
active-pending state without having executed a user instruction, and
will take a step exception earlier than expected when we return to
userspace.
Let's fix this by only advancing the state machine when skipping a user
instruction.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Andrey Konovalov <andreyknvl@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A compiler can optimize away memset calls by replacing them with mov
instructions. There are KASAN tests that specifically test that KASAN
correctly handles memset calls so we don't want this optimization to
happen.
The solution is to add -fno-builtin flag to test_kasan.ko
Link: http://lkml.kernel.org/r/105ec9a308b2abedb1a0d1fdced0c22d765e4732.1519924383.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Nick Terrell <terrelln@fb.com> Cc: Chris Mason <clm@fb.com> Cc: Yury Norov <ynorov@caviumnetworks.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: "Luis R . Rodriguez" <mcgrof@kernel.org> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com> Cc: Jeff Layton <jlayton@redhat.com> Cc: "Jason A . Donenfeld" <Jason@zx2c4.com> Cc: Kostya Serebryany <kcc@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable real_size is initialized with a value that is never read, it is
re-assigned a new value later on, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
lib/test_kasan.c:422:21: warning: Value stored to 'real_size' during its initialization is never read
Link: http://lkml.kernel.org/r/20180206144950.32457-1-colin.king@canonical.com Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "fs->location" is a u32 that comes from the user in ethtool_set_rxnfc().
We can't pass unclamped values to test_bit() or it results in an out of
bounds access beyond the end of the bitmap.
Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
marvell_get_sset_count() returns how many statistics counters there
are. If the PHY supports fibre, there are 3, otherwise two.
marvell_get_strings() does not make this distinction, and always
returns 3 strings. This then often results in writing past the end
of the buffer for the strings.
Fixes: 2170fef78a40 ("Marvell phy: add field to get errors from fiber link.") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rxrpc_destroy_all_calls(), there are two phases: (1) make sure the
->calls list is empty, emitting error messages if not, and (2) wait for the
RCU cleanup to happen on outstanding calls (ie. ->nr_calls becomes 0).
To avoid taking the call_lock, the function prechecks ->calls and if empty,
it returns to avoid taking the lock - this is wrong, however: it still
needs to go and do the second phase and wait for ->nr_calls to become 0.
Without this, the rxrpc_net struct may get deallocated before we get to the
RCU cleanup for the last calls. This can lead to:
Note the "61" at offset 0x58. This corresponds to the ->nr_calls member of
struct rxrpc_net (which is >9k in size, and thus allocated out of the 16k
slab).
Fix this by flipping the condition on the if-statement, putting the locked
section inside the if-body and dropping the return from there. The
function will then always go on to wait for the RCU cleanup on outstanding
calls.
Fixes: 2baec2c3f854 ("rxrpc: Support network namespacing") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the bnxt_init_one() error path, short FW command request memory
is not freed. This patch fixes it.
Fixes: e605db801bde ("bnxt_en: Support for Short Firmware Message") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver builds a list of multicast addresses and sends it to the
firmware when the driver's ndo_set_rx_mode() is called. In rare
cases, the firmware can fail this call if internal resources to
add multicast addresses are exhausted. In that case, we should
try the call again by setting the ALL_MCAST flag which is more
guaranteed to succeed.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Packet sockets in datagram mode take a destination address. Verify its
length before passing to dev_hard_header.
Prior to 2.6.14-rc3, the send code ignored sll_halen. This is
established behavior. Directly compare msg_namelen to dev->addr_len.
Change v1->v2: initialize addr in all paths
Fixes: 6b8d95f1795c4 ("packet: validate address length if non-zero") Suggested-by: David Laight <David.Laight@aculab.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As it shows, the first sctp_do_sm() running under atomic context (NET_RX
softirq) invoked sctp_primitive_ASCONF() that uses GFP_KERNEL flag later,
and this flag is supposed to be used in non-atomic context only. Besides,
sctp_do_sm() was called recursively, which is not expected.
Vlad tried to fix this recursive call in Commit c0786693404c ("sctp: Fix
oops when sending queued ASCONF chunks") by introducing a new command
SCTP_CMD_SEND_NEXT_ASCONF. But it didn't work as this command is still
used in the first sctp_do_sm() call, and sctp_primitive_ASCONF() will
be called in this command again.
To avoid calling sctp_do_sm() recursively, we send the next queued ASCONF
not by sctp_primitive_ASCONF(), but by sctp_sf_do_prm_asconf() in the 1st
sctp_do_sm() directly.
Reported-by: Ying Xu <yinxu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A request for a flowlabel fails in process or user exclusive mode must
fail if the caller pid or uid does not match. Invert the test.
Previously, the test was unsafe wrt PID recycling, but indeed tested
for inequality: fl1->owner != fl->owner
Fixes: 4f82f45730c68 ("net ip6 flowlabel: Make owner a union of struct pid* and kuid_t") Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory state around the buggy address: ffff888094012900: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc ffff888094012980: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc
>ffff888094012a00: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc
^ ffff888094012a80: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc ffff888094012b00: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc
Fixes: 4f82f45730c6 ("net ip6 flowlabel: Make owner a union of struct pid * and kuid_t") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, during fragmentation after forwarding, skb->skb_iif isn't
preserved, i.e. 'ip_copy_metadata' does not copy skb_iif from given
'from' skb.
As a result, ip_do_fragment's creates fragments with zero skb_iif,
leading to inconsistent behavior.
Assume for example an eBPF program attached at tc egress (post
forwarding) that examines __sk_buff->ingress_ifindex:
- the correct iif is observed if forwarding path does not involve
fragmentation/refragmentation
- a bogus iif is observed if forwarding path involves
fragmentation/refragmentatiom
Fix, by preserving skb_iif during 'ip_copy_metadata'.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The line6 driver uses a lot of USB buffers off of the stack, which is
not allowed on many systems, causing the driver to crash on some of
them. Fix this up by dynamically allocating the buffers with kmalloc()
which allows for proper DMA-able memory.
There are a few system calls (pselect, ppoll, etc) which replace a task
sigmask while they are running in a kernel-space
When a task calls one of these syscalls, the kernel saves a current
sigmask in task->saved_sigmask and sets a syscall sigmask.
On syscall-exit-stop, ptrace traps a task before restoring the
saved_sigmask, so PTRACE_GETSIGMASK returns the syscall sigmask and
PTRACE_SETSIGMASK does nothing, because its sigmask is replaced by
saved_sigmask, when the task returns to user-space.
This patch fixes this problem. PTRACE_GETSIGMASK returns saved_sigmask
if it's set. PTRACE_SETSIGMASK drops the TIF_RESTORE_SIGMASK flag.
Link: http://lkml.kernel.org/r/20181120060616.6043-1-avagin@gmail.com Fixes: 29000caecbe8 ("ptrace: add ability to get/set signal-blocked mask") Signed-off-by: Andrei Vagin <avagin@gmail.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
If a device has an exclusion range specified in the IVRS
table, this region needs to be reserved in the iova-domain
of that device. This hasn't happened until now and can cause
data corruption on data transfered with these devices.
Treat exclusion ranges as reserved regions in the iommu-core
to fix the problem.
Fixes: be2a022c0dd0 ('x86, AMD IOMMU: add functions to parse IOMMU memory mapping requirements for devices') Signed-off-by: Joerg Roedel <jroedel@suse.de> Reviewed-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
Backspace is not working on some terminal emulators which do not send the
key code defined by terminfo. Terminals either send '^H' (8) or '^?' (127).
But currently only '^?' is handled. Let's also handle '^H' for those
terminals.
If the call to of_gpiochip_scan_gpios() in of_gpiochip_add() fails, no
error handling is performed. This lead to the need of callers to call
of_gpiochip_remove() on failure, which causes "BAD of_node_put() on ..."
if the failure happened before the call to of_node_get().
Fix this by adding proper error handling.
Note that calling gpiochip_remove_pin_ranges() multiple times causes no
harm: subsequent calls are a no-op.
If an incoming ELS of type RSCN contains more than one element, zfcp
suboptimally causes repeated erp trigger NOP trace records for each
previously failed port. These could be ports that went away. It loops over
each RSCN element, and for each of those in an inner loop over all
zfcp_ports.
The trigger to recover failed ports should be just the reception of some
RSCN, no matter how many elements it has. So we can loop over failed ports
separately, and only then loop over each RSCN element to handle the
non-failed ports.
The call chain was:
zfcp_fc_incoming_rscn
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
In order the reduce the "flooding" of the REC trace area in such cases, we
factor out handling the failed ports to be outside of the entries loop:
zfcp_fc_incoming_rscn
if (no_entries > 1) <===
list_for_each_entry(port, &adapter->port_list, list) <===
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
Abbreviated example trace records before this code change:
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x02
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x00 NOP => superfluous trace record
The last trace entry repeats if there are more than 2 RSCN elements.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Reviewed-by: Jens Remus <jremus@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
free the symlink body after the same RCU delay we have for freeing the
struct inode itself, so that traversal during RCU pathwalk wouldn't step
into freed memory.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
meson_drv_bind() registers a meson_drm struct as the device's privdata,
but meson_drv_unbind() tries to retrieve a drm_device. This may cause a
segfault on shutdown:
projects / people / arne_f / kernel.git / log
