Douglas Anderson [Fri, 11 Jun 2021 17:17:37 +0000 (10:17 -0700)]
dt-bindings: display: simple: List hpd properties in panel-simple
The HPD (Hot Plug Detect) signal is present in many (probably even
"most") eDP panels. For eDP, this signal isn't actually used for
detecting hot-plugs of the panel but is more akin to a "panel ready"
signal. After you provide power to the panel, panel timing diagrams
typically say that you should wait for HPD to be asserted (or wait a
fixed amount of time) before talking to the panel.
The panel-simple bindings describes many eDP panels and many of these
panels provide the HPD signal. We should add the HPD-related
properties to the panel-simple bindings. The HPD properties are
actually defined in panel-common.yaml, so adding them here just
documents that they are OK for panels handled by the panel-simple
bindings.
NOTE: whether or not we'd include HPD properties in the panel node is
more a property of the board design than the panel itself. For most
boards using these eDP panels everything "magically" works without
specifying any HPD properties and that's been why we haven't needed to
allow the HPD properties earlier. On these boards the HPD signal goes
directly to a dedicated "HPD" input to the eDP controller and this
connection doesn't need to be described in the device tree. The only
time the HPD properties are needed in the device tree are if HPD is
hooked up to a GPIO or if HPD is normally on the panel but isn't used
on a given board. That means that if we don't allow the HPD properties
in panel-simple then one could argue that we've got to boot all eDP
panels (or at least all those that someone could conceivably put on a
system where HPD goes to a GPIO or isn't hooked up) from panel-simple.
Linus Walleij [Thu, 10 Jun 2021 22:05:27 +0000 (00:05 +0200)]
drm/panel: db7430: Add driver for Samsung DB7430
This adds a new driver for the Samsung DB7430 DPI display
controller as controlled over SPI.
Right now the only panel product we know that is using this
display controller is the LMS397KF04 but there may be more.
This is the first regular panel driver making use of the
MIPI DBI helper library. The DBI "device" portions can not
be used because that code assumes the use of a single
regulator and specific timings around the reset pulse that
do not match the DB7430 datasheet.
Leandro Ribeiro [Wed, 9 Jun 2021 23:00:38 +0000 (20:00 -0300)]
drm/doc: document how userspace should find out CRTC index
In this patch we add a section to document what userspace should do to
find out the CRTC index. This is important as they may be many places in
the documentation that need this, so it's better to just point to this
section and avoid repetition.
Vivek Kasireddy [Wed, 9 Jun 2021 18:29:15 +0000 (11:29 -0700)]
udmabuf: Add support for mapping hugepages (v4)
If the VMM's (Qemu) memory backend is backed up by memfd + Hugepages
(hugetlbfs and not THP), we have to first find the hugepage(s) where
the Guest allocations are located and then extract the regular 4k
sized subpages from them.
v2: Ensure that the subpage and hugepage offsets are calculated correctly
when the range of subpage allocations cuts across multiple hugepages.
v3: Instead of repeatedly looking up the hugepage for each subpage,
only do it when the subpage allocation crosses over into a different
hugepage. (suggested by Gerd and DW)
v4: Fix the following warning identified by checkpatch:
CHECK:OPEN_ENDED_LINE: Lines should not end with a '('
Alex Deucher [Mon, 7 Jun 2021 20:19:46 +0000 (16:19 -0400)]
drm/amdgpu/vcn: drop gfxoff control for VCN2+
Drop disabling of gfxoff during VCN use. This allows gfxoff
to kick in and potentially save power if the user is not using
gfx for color space conversion or scaling.
VCN1.0 had a bug which prevented it from working properly with
gfxoff, so we disabled it while using VCN. That said, most apps
today use gfx for scaling and color space conversion rather than
overlay planes so it was generally in use anyway. This was fixed
on VCN2+, but since we mostly use gfx for color space conversion
and scaling and rapidly powering up/down gfx can negate the
advantages of gfxoff, we left gfxoff disabled. As more
applications use overlay planes for color space conversion
and scaling, this starts to be a win, so go ahead and leave
gfxoff enabled.
Note that VCN1.0 uses vcn_v1_0_idle_work_handler() and
vcn_v1_0_ring_begin_use() so they are not affected by this
patch.
Reviewed-by: James Zhu <James.Zhu@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Boyuan Zhang <Boyuan.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* ttm: Make struct ttm_resource the base of all managers + changes
in all users of TTM; Add a generic memcpy for page-based iomem; Remove
use of VM_MIXEDMAP; Cleanups
Driver Changes:
* drm/bridge: Add TI SN65DSI83 and SN65DSI84 + DT bindings
* drm/hyperv: Add DRM driver for HyperV graphics output
* drm/msm: Fix module dependencies
* drm/panel: KD53T133: Support rotation
* drm/pl111: Fix module dependencies
* drm/qxl: Fixes
* drm/stm: Cleanups
* drm/sun4i: Be explicit about format modifiers
* drm/vc4: Use struct gpio_desc; Cleanups
* drm/vgem: Cleanups
* drm/vmwgfx: Use ttm_bo_move_null() if there's nothing to copy
Lyude Paul [Fri, 14 May 2021 18:15:03 +0000 (14:15 -0400)]
drm/nouveau/kms/nv50-: Add basic DPCD backlight support for nouveau
This adds support for controlling panel backlights over eDP using VESA's
standard backlight control interface. Luckily, Nvidia was cool enough to
never come up with their own proprietary backlight control interface (at
least, not any that I or the laptop manufacturers I've talked to are aware
of), so this should work for any laptop panels which support the VESA
backlight control interface.
Note that we don't yet provide the panel backlight frequency to the DRM DP
backlight helpers. This should be fine for the time being, since it's not
required to get basic backlight controls working.
For reference: there's some mentions of PWM backlight values in
nouveau_reg.h, but I'm not sure these are the values we would want to use.
If we figure out how to get this information in the future, we'll have the
benefit of more granular backlight control.
Lyude Paul [Fri, 14 May 2021 18:15:02 +0000 (14:15 -0400)]
drm/dp: Extract i915's eDP backlight code into DRM helpers
Since we're about to implement eDP backlight support in nouveau using the
standard protocol from VESA, we might as well just take the code that's
already written for this and move it into a set of shared DRM helpers.
Note that these helpers are intended to handle DPCD related backlight
control bits such as setting the brightness level over AUX, probing the
backlight's TCON, enabling/disabling the backlight over AUX if supported,
etc. Any PWM-related portions of backlight control are explicitly left up
to the driver, as these will vary from platform to platform.
The only exception to this is the calculation of the PWM frequency
pre-divider value. This is because the only platform-specific information
required for this is the PWM frequency of the panel, which the driver is
expected to provide if available. The actual algorithm for calculating this
value is standard and is defined in the eDP specification from VESA.
Note that these helpers do not yet implement the full range of features
the VESA backlight interface provides, and only provide the following
functionality (all of which was already present in i915's DPCD backlight
support):
* Basic control of brightness levels
* Basic probing of backlight capabilities
* Helpers for enabling and disabling the backlight
v3:
* Split out changes to i915's backlight code to separate patches to make it
easier to review
v4:
* Style/spelling changes from Thomas Zimmermann
v5:
* Start using new drm_dbg_*() functions
Lyude Paul [Fri, 14 May 2021 18:15:01 +0000 (14:15 -0400)]
drm/i915/dpcd_bl: Print return codes for VESA backlight failures
Also, stop printing the DPCD register that failed, and just describe it
instead. Saves us from having to look up each register offset when reading
through kernel logs (plus, DPCD dumping with drm.debug |= 0x100 will give
us that anyway).
Lyude Paul [Fri, 14 May 2021 18:15:00 +0000 (14:15 -0400)]
drm/i915/dpcd_bl: Return early in vesa_calc_max_backlight if we can't read PWMGEN_BIT_COUNT
If we can't read DP_EDP_PWMGEN_BIT_COUNT in
intel_dp_aux_vesa_calc_max_backlight() but do have a valid PWM frequency
defined in the VBT, we'll keep going in the function until we inevitably
fail on reading DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN. There's not much point in
doing this, so just return early.
Lyude Paul [Fri, 14 May 2021 18:14:58 +0000 (14:14 -0400)]
drm/i915/dpcd_bl: Cache some backlight capabilities in intel_panel.backlight
Since we're about to be moving this code into shared DRM helpers, we might
as well start to cache certain backlight capabilities that can be
determined from the EDP DPCD, and are likely to be relevant to the majority
of drivers using said helpers. The main purpose of this is just to prevent
every driver from having to check everything against the eDP DPCD using DP
macros, which makes the code slightly easier to read (especially since the
names of some of the eDP capabilities don't exactly match up with what we
actually need to use them for, like DP_EDP_BACKLIGHT_BRIGHTNESS_BYTE_COUNT
for instance).
This is kind of an annoying aspect of DRM's DP helpers:
drm_dp_dpcd_readb/writeb() return the size of bytes read/written on
success, thus we want to check against that instead of checking if the
return value is less than 0.
I'll probably be fixing this in the near future once I start doing DP work
again, also because I'd rather not mix a tree-wide refactor like that in
with a patch series intended to be around introducing DP backlight helpers.
So, for now let's just handle the return values from each function
correctly.
Lyude Paul [Fri, 14 May 2021 18:14:55 +0000 (14:14 -0400)]
drm/i915/dpcd_bl: Remove redundant AUX backlight frequency calculations
Noticed this while moving all of the VESA backlight code in i915 over to
DRM helpers: it would appear that we calculate the frequency value we want
to write to DP_EDP_BACKLIGHT_FREQ_SET twice even though this value never
actually changes during runtime. So, let's simplify things by just caching
this value in intel_panel.backlight, and re-writing it as-needed.
Changes since v1:
* Wrap panel->backlight.edp.vesa.pwm_freq_pre_divider in
DP_EDP_BACKLIGHT_FREQ_AUX_SET_CAP check - Jani
drm/i915/adl_p: Same slices mask is not same Dbuf state
We currently treat same slice mask as a same DBuf state and skip
updating the Dbuf slices, if we detect that.
This is wrong as if we have a multi to single pipe change or
vice versa, that would be treated as a same Dbuf state and thus
no changes required, so we don't get Mbus updated, causing issues.
Solution: check also mbus_join, in addition to slices mask.
Marek Vasut [Tue, 8 Jun 2021 14:22:11 +0000 (16:22 +0200)]
drm/bridge: ti-sn65dsi83: Fix sparse warnings
Fix the following sparse warnings generated by "make C=1":
drivers/gpu/drm/bridge/ti-sn65dsi83.c:429:13: warning: incorrect type in assignment (different base types)
drivers/gpu/drm/bridge/ti-sn65dsi83.c:429:13: expected unsigned short [assigned] [usertype] val
drivers/gpu/drm/bridge/ti-sn65dsi83.c:429:13: got restricted __le16 [usertype]
drivers/gpu/drm/bridge/ti-sn65dsi83.c:432:13: warning: incorrect type in assignment (different base types)
drivers/gpu/drm/bridge/ti-sn65dsi83.c:432:13: expected unsigned short [addressable] [assigned] [usertype] val
drivers/gpu/drm/bridge/ti-sn65dsi83.c:432:13: got restricted __le16 [usertype]
drivers/gpu/drm/bridge/ti-sn65dsi83.c:436:13: warning: incorrect type in assignment (different base types)
drivers/gpu/drm/bridge/ti-sn65dsi83.c:436:13: expected unsigned short [addressable] [assigned] [usertype] val
drivers/gpu/drm/bridge/ti-sn65dsi83.c:436:13: got restricted __le16 [usertype]
drivers/gpu/drm/bridge/ti-sn65dsi83.c:438:13: warning: incorrect type in assignment (different base types)
drivers/gpu/drm/bridge/ti-sn65dsi83.c:438:13: expected unsigned short [addressable] [assigned] [usertype] val
drivers/gpu/drm/bridge/ti-sn65dsi83.c:438:13: got restricted __le16 [usertype]
drivers/gpu/drm/bridge/ti-sn65dsi83.c:441:13: warning: incorrect type in assignment (different base types)
drivers/gpu/drm/bridge/ti-sn65dsi83.c:441:13: expected unsigned short [addressable] [assigned] [usertype] val
drivers/gpu/drm/bridge/ti-sn65dsi83.c:441:13: got restricted __le16 [usertype]
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Adam Ford <aford173@gmail.com> Cc: Douglas Anderson <dianders@chromium.org> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Loic Poulain <loic.poulain@linaro.org> Cc: Marek Vasut <marex@denx.de> Cc: Philippe Schenker <philippe.schenker@toradex.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Valentin Raevsky <valentin@compulab.co.il>
To: dri-devel@lists.freedesktop.org Signed-off-by: Robert Foss <robert.foss@linaro.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210608142211.82333-1-marex@denx.de
Colin Ian King [Tue, 8 Jun 2021 16:13:13 +0000 (17:13 +0100)]
drm: qxl: ensure surf.data is ininitialized
The object surf is not fully initialized and the uninitialized
field surf.data is being copied by the call to qxl_bo_create
via the call to qxl_gem_object_create. Set surf.data to zero
to ensure garbage data from the stack is not being copied.
Ville Syrjälä [Tue, 8 Jun 2021 08:54:15 +0000 (11:54 +0300)]
drm/i915: Disable PSR around cdclk changes
AUX logic is often clocked from cdclk. Disable PSR to make sure
there are no hw initiated AUX transactions in flight while we
change the cdclk frequency.
Gwan-gyeong Mun [Tue, 8 Jun 2021 08:54:14 +0000 (11:54 +0300)]
drm/i915/display: Introduce new intel_psr_pause/resume function
This introduces the following function that can exit and activate a psr
source when intel_psr is already enabled.
- intel_psr_pause(): Pause current PSR. It deactivates current psr state.
- intel_psr_resume(): Resume paused PSR. It activates paused psr state.
v2: Address Jose's review comment.
- Remove unneeded changes around the intel_psr_enable().
- Add intel_psr_post_exit() which processes waiting until PSR is idle
and WA for SelectiveFetch.
v3: Address Jose's review comment.
- Rename intel_psr_post_exit() to intel_psr_wait_exit_locked().
- Move WA_1408330847 to intel_psr_disable_locked()
- If the PSR is paused by an explicit intel_psr_paused() call, make the
intel_psr_flush() not to activate PSR.
v4: Address Jose's review comment.
- In order to avoid the scenario of PSR is not active but there is a
scheduled psr->work, it changes the check routine of intel_psr_pause()
for PSR's enablement from "psr->active" to "psr->enable".
Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210608085415.515342-1-gwan-gyeong.mun@intel.com
Marek Vasut [Mon, 7 Jun 2021 17:24:57 +0000 (19:24 +0200)]
drm/stm: Remove usage of drm_display_mode_to_videomode()
There is not much value in the extra conversion step, the calculations
required for the LTDC IP are different than what is used in the
drm_display_mode_to_videomode(), so just do the right ones in the LTDC
driver right away.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Antonio Borneo <antonio.borneo@foss.st.com> Cc: Benjamin Gaignard <benjamin.gaignard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Philippe Cornu <philippe.cornu@foss.st.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Vincent Abriou <vincent.abriou@foss.st.com> Cc: Yannick Fertre <yannick.fertre@foss.st.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com
To: dri-devel@lists.freedesktop.org Tested-by: Yannick Fertré <yannick.fertre@st.com> Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210607172457.14471-1-marex@denx.de
Po-Ting Chen [Wed, 5 May 2021 12:46:36 +0000 (20:46 +0800)]
drm/amd/display: Add swizzle visual confirm mode
[Why]
To support a new visual confirm mode: swizzle to show the specific
color at the screen border according to different surface swizzle mode.
Currently we only support the Linear mode with red color.
Signed-off-by: Po-Ting Chen <robin.chen@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: force CP to DESIRED when removing display
[WHY]
- Commit from userspace could cause link stream to disable and hdcp
auth to reset when the HDCP has already been enabled at the moment.
CP should fall back to DESIRED from ENABLED in such cases.
- This change was previously reverted due to a regression caused, which
has now been cleared.
[HOW]
In hdcp display removal, change CP to DESIRED if at the moment CP
is ENABLED before the auth reset and removal of linked list element.
Signed-off-by: Dingchen (David) Zhang <dingchen.zhang@amd.com> Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Bernstein [Wed, 26 May 2021 19:22:51 +0000 (15:22 -0400)]
drm/amd/display: Updates for ODM Transition Test
[Why]
There is an assert in cases where transition from ODM 2:1
to ODM 1:1 (bypass)
[How]
Remove assert since this case is now valid.
Update diags tests for ODM transitions.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Roy Chan [Thu, 20 May 2021 20:20:39 +0000 (16:20 -0400)]
drm/amd/display: Revert "Disconnect non-DP with no EDID"
[Why]
Found a use case (IPKVM) that DP-VGA active dongle does
not return any EDID and the mentioned commit broke it.
[How]
This reverts "Disconnect non-DP with no EDID"
Signed-off-by: Roy Chan <roy.chan@amd.com> Reviewed-by: Chris Park <Chris.Park@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fangzhi Zuo [Wed, 26 May 2021 00:39:12 +0000 (20:39 -0400)]
drm/amd/display: Add debugfs entry for dsc passthrough
[Why & How]
Add debugfs entry to force dsc decoding at PCON when DSC capable
external RX is connected. In such case, it is free to test DSC
decoding at external RX or at PCON.
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Anthony Koo [Sat, 22 May 2021 23:45:46 +0000 (19:45 -0400)]
drm/amd/display: [FW Promotion] Release 0.0.68
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Vladimir Stempen [Wed, 19 May 2021 17:55:46 +0000 (13:55 -0400)]
drm/amd/display: Release MST resources on switch from MST to SST
[why]
When OS overrides training link training parameters
for MST device to SST mode, MST resources are not
released and leak of the resource may result crash and
incorrect MST discovery during following hot plugs.
[how]
Retaining sink object to be reused by SST link and
releasing MST resources.
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mikita Lipski [Wed, 19 May 2021 21:32:16 +0000 (17:32 -0400)]
drm/amd/display: Enable PSR Residency for multiple panels
[why]
Allow specifying which panel to take PSR Residency
measurements from.
[how]
Pass panel instance to DMUB through GPINT in the upper
8 bits of the parameter.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Return last used DRR VTOTAL from DC
[How]
Add call to get the last used VTOTAL from DC
Signed-off-by: Jayendran Ramani <Jayendran.Ramani@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Remove unused definition of DMUB SET_CONFIG
[Why & How]
SET_CONFIG transactions with DMUB is not used and removed.
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Roman Li [Fri, 21 May 2021 14:20:25 +0000 (10:20 -0400)]
drm/amd/display: Update scaling settings on modeset
[Why]
We update scaling settings when scaling mode has been changed.
However when changing mode from native resolution the scaling mode previously
set gets ignored.
[How]
Perform scaling settings update on modeset.
Signed-off-by: Roman Li <roman.li@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jimmy Kizito [Wed, 21 Apr 2021 14:34:34 +0000 (10:34 -0400)]
drm/amd/display: Support mappable encoders when transmitting training patterns.
[Why & How]
Add support for transmitting training pattern sequences for links whose
encoders have been dynamically assigned.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add functionality useful for DP equalization phase of link training to
public interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change was found to break some high-refresh modes. Reverting
to unblock mainline.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com> Reviewed-by: Sung Lee <Sung.Lee@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wyatt Wood [Thu, 6 May 2021 20:11:16 +0000 (16:11 -0400)]
drm/amd/display: Refactor visual confirm
[Why + How]
Visual confirm has no asic-specific logic,
so we can refactor and unify these functions
that are currently spread out across multiple
dcn files.
Add a new hw sequencer interface update_visual_confirm_color,
and a new mpc function pointer set_bg_color.
This will allow visual confirm to updated independently
of MPCC blending updates.
v2: squash in DCN3.1 fixes
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
JinZe.Xu [Tue, 18 May 2021 06:36:37 +0000 (14:36 +0800)]
drm/amd/display: Control power gating by driver.
[Why]
This disablement would be specific for Nav10 and shouldn’t be propagated to the other programs.
[How]
Power gating is controlled by driver.
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nikola Cornij [Tue, 18 May 2021 16:33:12 +0000 (12:33 -0400)]
drm/amd/display: Fix DCN 3.01 DSCCLK validation
[why]
DSCCLK validation is not necessary because DSCCLK is derrived from
DISPCLK, therefore if DISPCLK validation passes, DSCCLK is valid, too.
Doing DSCLK validation in addition to DISPCLK leads to modes being
wrongly rejected when DSCCLK was incorrectly set outside of DML.
[how]
Remove DSCCLK validation because it's implicitly validated under DISPCLK
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wenjing Liu [Mon, 17 May 2021 19:54:19 +0000 (15:54 -0400)]
drm/amd/display: delay 100ms before restart after failing to read CP_IRQ
[why]
Some DPRX will issue CP_IRQ when user disconnects a display
that has been authenticated.
Since display is being disconnecting dpcd read will fail.
This will cause us to attempt HDCP retry on disconnection.
We are adding a 100ms delay before retry.
So we will only start retry if within 100ms there is no disconnection call
to HDCP module.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mikita Lipski [Mon, 17 May 2021 22:18:25 +0000 (18:18 -0400)]
drm/amd/display: Enabling PSR support for multiple panels
[why]
Updating PSR interfaces to allow PSR enablement
per eDP panel.
[how]
- Copying PSR command structures to DC
- Changing function interfaces to pass panel instance
- Communicating with DMUB per link instead of assuming
to use a single one
-Iterating through all PSR capable panels when enabling/disabling
all
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jake Wang [Fri, 14 May 2021 19:41:39 +0000 (15:41 -0400)]
drm/amd/display: Trigger full update after DCC on/off
[Why]
During DCC on/off, stutter period is calculated before DCC has fully transitioned.
This results in incorrect stutter period calculation.
[How]
Trigger a full update when DCC changes between on/off.
Signed-off-by: Jake Wang <haonan.wang2@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaomeng Hou [Mon, 7 Jun 2021 08:36:41 +0000 (16:36 +0800)]
drm/amd/pm: fix warning reported by kernel test robot
Kernel test robot throws warning ->
>> drivers/gpu/drm/amd/amdgpu/../pm/swsmu/smu13/yellow_carp_ppt.c:483:2:
warning: variable 'member_type' is used uninitialized whenever switch
default is taken [-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/gpu/drm/amd/amdgpu/../pm/swsmu/smu13/yellow_carp_ppt.c:487:47:
note: uninitialized use occurs here
return yellow_carp_get_smu_metrics_data(smu, member_type, value);
^~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../pm/swsmu/smu13/yellow_carp_ppt.c:465:2:
note: variable 'member_type' is declared here
MetricsMember_t member_type;
^
1 warning generated.
Fix this warning by return errno when the clk type is unsupported.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Xiaomeng Hou <Xiaomeng.Hou@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nirmoy Das [Tue, 8 Jun 2021 09:58:48 +0000 (11:58 +0200)]
drm/amdgpu: fix shadow bo skip condition
Create shadow BOs only for no-compute VM context and only for dGPU.
The existing if-condition would create shadow bo for compute context
on dGPU which not what we wanted.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Darren Powell [Wed, 26 May 2021 21:31:16 +0000 (17:31 -0400)]
amdgpu/pm: modify and add smu_get_power_limit to Powerplay API
modify args of smu_get_power_limit to match Powerplay API .get_power_limit
add smu_get_power_limit to Powerplay API swsmu_pm_funcs
remove special handling of smu in amdgpu_hwmon_show_power_cap*
Darren Powell [Sat, 22 May 2021 04:13:53 +0000 (00:13 -0400)]
amdgpu/pm: modify Powerplay API get_power_limit to use new pp_power enums
updated {amd_pm_funcs}->get_power_limit() signature
rewrote pp_get_power_limit to use new enums
pp_get_power_limit now returns -EOPNOTSUPP for unknown power limit
update calls to {amd_pm_funcs}->get_power_limit()
* Test Notes
* testing hardware was NAVI10 (tests SMU path)
** needs testing on VANGOGH
** needs testing on SMU < 11
** ie, one of
TOPAZ, FIJI, TONGA, POLARIS10, POLARIS11, POLARIS12, VEGAM, CARRIZO,
STONEY, VEGA10, VEGA12,VEGA20, RAVEN, BONAIRE, HAWAII
Darren Powell [Sat, 22 May 2021 02:37:24 +0000 (22:37 -0400)]
amdgpu/pm: clean up smu_get_power_limit function signature
add two new powerplay enums (limit_level, type)
add enums to smu_get_power_limit signature
remove input bitfield stuffing of output variable limit
update calls to smu_get_power_limit
Fix checkpatch.pl --strict -f drivers/gpu/drm/bridge/ti-sn65dsi83.c
CHECKs, no functional change. This is the same modification done
to V7 of the original patch.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Adam Ford <aford173@gmail.com> Cc: Douglas Anderson <dianders@chromium.org> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Loic Poulain <loic.poulain@linaro.org> Cc: Marek Vasut <marex@denx.de> Cc: Philippe Schenker <philippe.schenker@toradex.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Valentin Raevsky <valentin@compulab.co.il>
To: dri-devel@lists.freedesktop.org Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210608095322.23644-1-marex@denx.de
Christian König [Tue, 1 Jun 2021 17:47:50 +0000 (19:47 +0200)]
drm/ttm: nuke VM_MIXEDMAP on BO mappings v3
We discussed if that is really the right approach for quite a while now, but
digging deeper into a bug report on arm turned out that this is actually
horrible broken right now.
The reason for this is that vmf_insert_mixed_prot() always tries to grab
a reference to the underlaying page on architectures without
ARCH_HAS_PTE_SPECIAL and as far as I can see also enabled GUP.
So nuke using VM_MIXEDMAP here and use VM_PFNMAP instead.
Also make sure to reject mappings without VM_SHARED.
v2: reject COW mappings, merge function with only caller
v3: adjust comment as suggested by Thomas
Marek Vasut [Mon, 7 Jun 2021 17:42:58 +0000 (19:42 +0200)]
drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver
Add driver for TI SN65DSI83 Single-link DSI to Single-link LVDS bridge
and TI SN65DSI84 Single-link DSI to Dual-link or 2x Single-link LVDS
bridge. TI SN65DSI85 is unsupported due to lack of hardware to test on,
but easy to add.
The driver operates the chip via I2C bus. Currently the LVDS clock are
always derived from DSI clock lane, which is the usual mode of operation.
Support for clock from external oscillator is not implemented, but it is
easy to add if ever needed. Only RGB888 pixel format is implemented, the
LVDS666 is not supported, but could be added if needed.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Adam Ford <aford173@gmail.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Douglas Anderson <dianders@chromium.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Loic Poulain <loic.poulain@linaro.org> Cc: Philippe Schenker <philippe.schenker@toradex.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Valentin Raevsky <valentin@compulab.co.il>
To: dri-devel@lists.freedesktop.org Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210607174258.16300-2-marex@denx.de
Marek Vasut [Mon, 7 Jun 2021 17:42:57 +0000 (19:42 +0200)]
dt-bindings: drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 bindings
Add DT binding document for TI SN65DSI83 and SN65DSI84 DSI to LVDS bridge.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Douglas Anderson <dianders@chromium.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Stephen Boyd <swboyd@chromium.org> Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210607174258.16300-1-marex@denx.de
Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Huang [Sat, 5 Jun 2021 14:43:00 +0000 (10:43 -0400)]
drm/amdgpu: Fix warning of Function parameter or member not described
Add the parameter table_freed description on function description.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wan Jiabing [Sat, 5 Jun 2021 02:54:06 +0000 (10:54 +0800)]
drm/amdkfd: remove duplicate include of kfd_svm.h
kfd_svm.h is included duplicately in commit 42de677f79999
("drm/amdkfd: register svm range").
After checking possible related header files,
remove the former one to make the code format more reasonable.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Sat, 5 Jun 2021 14:46:10 +0000 (16:46 +0200)]
drm/amdgpu: fix VM handling for GART allocations
For GTT allocations with a GART address the res contains the VMID0
addresses and can't be used for VM handling.
So ignore the res when the pages array is given or we fill the page
tables with nonsense.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Nirmoy Das <nirmoy.das@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Peng Ju Zhou [Mon, 7 Jun 2021 05:40:56 +0000 (13:40 +0800)]
drm/amdgpu: Fixing "Indirect register access for Navi12 sriov" for vega10
The NV12 and VEGA10 share the same interface W/RREG32_SOC15*,
the callback functions in these macros may not be defined,
so NULL pointer must be checked but not in
macro __WREG32_SOC15_RLC__, fixing the lock of NULL pointer check.
Signed-off-by: Peng Ju Zhou <PengJu.Zhou@amd.com> Reviewed-by: Emily Deng <Emily.Deng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Thu, 3 Jun 2021 08:10:04 +0000 (16:10 +0800)]
drm/amdkfd: add sdma poison consumption handling
Follow the same apporach as GFX to handle SDMA
poison consumption. Send SIGBUS to application
when receives SDMA_ECC interrupt and issue gpu
reset either mode 2 or mode 1 to get the engine
back
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Dennis Li<dennis.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Philip Yang [Fri, 4 Jun 2021 20:22:58 +0000 (16:22 -0400)]
drm/amdkfd: pages_addr offset must be 0 for system range
prange->offset is for VRAM range mm_nodes, if multiple ranges share same
mm_nodes, migrate range back to VRAM will reuse the VRAM at offset of
the same mm_nodes. For system memory pages_addr array, the offset is
always 0, otherwise, update GPU mapping will use incorrect system memory
page, and cause system memory corruption.
Signed-off-by: Philip Yang <Philip.Yang@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/i915/display: Allow fastsets when DP_SDP_VSC infoframe do not match with PSR enabled
When PSR is enabled it handles DP_SDP_VSC, changing revision and all
the other fields as necessary.
It can also enabled and disable this SDP as needed without a full
modeset.
So here masking DP_SDP_VSC bit when previous and future state PSR
enabled, it will still be checked when comparing the asked state
to what was programmed to hardware.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Fixes: 78b772e1a01f ("drm/i915/display: Fill PSR state during hardware configuration read out") Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210514232247.144542-2-jose.souza@intel.com
Commit 78b772e1a01f ("drm/i915/display: Fill PSR state during hardware
configuration read out") is not allowing fastsets to happen when PSR
states changes but PSR is a feature that can be enabled and disabled
during fastsets.
So here moving the PSR pipe conf checks to a block that is only
executed when checking if HW state matches with requested state, not
during the phase where it checks if fastset is possible or not.
There still a state mismatch not allowing fastsets between states
turning off or on PSR because of crtc_state->infoframes.enable
BIT(DP_SDP_VSC) but at least for now it will allow a fastset between
PSR1 <-> PSR2, that is a case heavilly used by CI due to pipe CRC not
work with PSR2, but the remaning issue will be fixed in a future patch.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Fixes: 78b772e1a01f ("drm/i915/display: Fill PSR state during hardware configuration read out") Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210514232247.144542-1-jose.souza@intel.com
Deepak Rawat [Thu, 27 May 2021 11:22:28 +0000 (04:22 -0700)]
drm/hyperv: Add DRM driver for hyperv synthetic video device
DRM driver for hyperv synthetic video device, based on hyperv_fb
framebuffer driver. Also added config option "DRM_HYPERV" to enabled
this driver.
v2:
- Add support for gen2 VM
- Fixed review comments
v3:
- Split into multiple files as suggested by Thomas Zimmermann
- Fixed hibernation issue as suggested by Dexuan Cui
- Use ioremap_cache as suggested by Dexuan Cui
- Incorporated other review comments
v4:
- Fix bitrotted code
- Review comments
- Updated the copyright and license to match hyperv_fb
v5:
- Address review comments and rebased with drm-misc-next
v6:
- Minor code/comment improvement as suggested by Dexuan Cui