Ville Syrjälä [Thu, 9 May 2019 12:21:59 +0000 (15:21 +0300)]
drm/i915: Bump gen7+ fb size limits to 16kx16k
With gtt remapping in place we can use arbitrarily large
framebuffers. Let's bump the limits to 16kx16k on gen7+.
The limit was chosen to match the maximum 2D surface size
of the 3D engine.
With the remapping we could easily go higher than that for the
display engine. However the modesetting ddx will blindly assume
it can handle whatever is reported via kms. The oversized
buffer dimensions are not caught by glamor nor Mesa until
finally an assert will trip when genxml attempts to pack the
SURFACE_STATE. So we pick a safe limit to avoid the X server
from crashing (or potentially misbehaving if the genxml asserts
are compiled out).
Ville Syrjälä [Thu, 9 May 2019 12:21:58 +0000 (15:21 +0300)]
drm/i915: Bump fb stride limit to 128KiB for gen4+ and 256KiB for gen7+
With gtt remapping plugged in we can simply raise the stride
limit on gen4+. Let's just pick the limit to match the render
engine max stride (256KiB on gen7+, 128KiB on gen4+).
No remapping CCS because the virtual address of each page actually
matters due to the new hash mode
(WaCompressedResourceDisplayNewHashMode:skl,kbl etc.), and no
remapping on gen2/3 due extra complications from fence alignment
and gen2 2KiB GTT tile size. Also no real benefit since the
display engine limits already match the other limits.
v2: Rebase due to is_ccs_modifier()
v3: Tweak the comment and commit msg
v4: Fix gen4+ stride limit to be 128KiB
Ville Syrjälä [Thu, 9 May 2019 12:21:56 +0000 (15:21 +0300)]
drm/i915: Overcome display engine stride limits via GTT remapping
The display engine stride limits are getting in our way. On SKL+
we are limited to 8k pixels, which is easily exceeded with three
4k displays. To overcome this limitation we can remap the pages
in the GTT to provide the display engine with a view of memory
with a smaller stride.
The code is mostly already there as We already play tricks with
the plane surface address and x/y offsets.
A few caveats apply:
* linear buffers need the fb stride to be page aligned, as
otherwise the remapped lines wouldn't start at the same
spot
* compressed buffers can't be remapped due to the new
ccs hash mode causing the virtual address of the pages
to affect the interpretation of the compressed data. IIRC
the old hash was limited to the low 12 bits so if we were
using that mode we could remap. As it stands we just refuse
to remapp with compressed fbs.
* no remapping gen2/3 as we'd need a fence for the remapped
vma, which we currently don't have. Need to deal with the
fence POT requirements, and do something about the gen2
gtt page size vs tile size difference
v2: Rebase due to is_ccs_modifier()
Fix up the skl+ stride_mult mess
memset() the gtt_view because otherwise we could leave
junk in plane[1] when going from 2 plane to 1 plane format
v3: intel_check_plane_stride() was split out
v4: Drop the aligned viewport stuff, it was meant for ccs which
can't be remapped anyway
v5: Introduce intel_plane_can_remap()
Reorder the code so that plane_state->view gets filled
even for invisible planes, otherwise we'd keep using
stale values and could explode during remapping. The new
logic never remaps invisible planes since we don't have
a viewport, and instead pins the full fb instead
v6: Fix plane src coord checks after remapping by moving
plane_state->base.src to the final plane x/y offsets.
Allow intel_plane_check_stride() to fail even with
remapping (can happen at least with a linear 64bpp
fb with a 4k plane and a suitably inconvenient src
coordinates).
Improve aux plane FIXME (Daniel)
Move some code shuffling into a separate patch (Daniel)
Ville Syrjälä [Thu, 9 May 2019 12:21:55 +0000 (15:21 +0300)]
drm/i915: Shuffle stride checking code around
Reorganize some fb stride checking code a bit to prepare for
gtt remapping. And do a bit of s/pitch/stride/ renaming in the
process for a bit more uniformity (apart from the whole
fb->pitches[] thing).
Ville Syrjälä [Thu, 9 May 2019 12:21:54 +0000 (15:21 +0300)]
drm/i915/selftests: Add live vma selftest
Add a live selftest to excercise rotated/remapped vmas. We simply
write through the rotated/remapped vma, and confirm that the data
appears in the right page when read through the normal vma.
Not sure what the fallout of making all rotated/remapped vmas
mappable/fenceable would be, hence I just hacked it in the test.
v2: Grab rpm reference (Chris)
GEM_BUG_ON(view.type not as expected) (Chris)
Allow CAN_FENCE for rotated/remapped vmas (Chris)
Update intel_plane_uses_fence() to ask for a fence
only for normal vmas on gen4+
v3: Deal with intel_wakeref_t
v4: Rebase
Ville Syrjälä [Thu, 9 May 2019 12:21:52 +0000 (15:21 +0300)]
drm/i915: Add a new "remapped" gtt_view
To overcome display engine stride limits we'll want to remap the
pages in the GTT. To that end we need a new gtt_view type which
is just like the "rotated" type except not rotated.
v2: Use intel_remapped_plane_info base type
s/unused/unused_mbz/ (Chris)
Separate BUILD_BUG_ON()s (Chris)
Use I915_GTT_PAGE_SIZE (Chris)
v3: Use i915_gem_object_get_dma_address() (Chris)
Trim the sg (Tvrtko)
v4: Actually trim this time. Limit the max length
to one row of pages to keep things simple
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190509122159.24376-2-ville.syrjala@linux.intel.com Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Chris Wilson [Wed, 15 May 2019 13:00:52 +0000 (14:00 +0100)]
drm/i915/execlists: Drop promotion on unsubmit
With the disappearance of NEWCLIENT, we no longer need to provide the
priority boost on preemption in order to prevent repeated gazumping,
and we can remove the dead code.
Chris Wilson [Wed, 15 May 2019 13:00:51 +0000 (14:00 +0100)]
drm/i915: Downgrade NEWCLIENT to non-preemptive
Commit 1413b2bc0717 ("drm/i915: Trim NEWCLIENT boosting") had the
intended consequence of not allowing a sequence of work that merely
crossed into a new engine the privilege to be promoted to NEWCLIENT
status. It also had the unintended consequence of actually making
NEWCLIENT effective on heavily oversubscribed transcode machines and
impacting upon their throughput.
If we consider a client packet composed of (rcsA, rcsB, vcs) and 30 of
those clients, using the NEWCLIENT boost that will be scheduled as
rcsA x 30, (rcsB, vcs) x 30
where as before it would have been
(rcsA, rcsB, vcs) x 30
That is with NEWCLIENT only boosting the first request of each client,
we would execute all rcsA requests prior to running on the vcs engines;
acruing a lot of dead time as compared to the previous case where the
vcs engine would be started in parallel to processing the second client.
The previous patch has the effect of delaying submission until it is
required by a third party (either the user with an explicit wait, or by
another client/engine). We reduce the NEWCLIENT bump to a mere WAIT,
which has the effect of removing its preemptive grant and reducing it to
the same level as any other user interaction -- that it will not be
promoted above the interengine dependencies, and so preventing NEWCLIENTS
from starving other engines. This a large nerf to the rrul properties of
the current NEWCLIENT, but it still does give prioritised submission to
new requests from light workloads.
References: b16c765122f9 ("drm/i915: Priority boost for new clients") Fixes: 1413b2bc0717 ("drm/i915: Trim NEWCLIENT boosting") # customer impact Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com> Cc: Dmitry Ermilov <dmitry.ermilov@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190515130052.4475-4-chris@chris-wilson.co.uk
Chris Wilson [Wed, 15 May 2019 13:00:50 +0000 (14:00 +0100)]
drm/i915: Bump signaler priority on adding a waiter
The handling of the no-preemption priority level imposes the restriction
that we need to maintain the implied ordering even though preemption is
disabled. Otherwise we may end up with an AB-BA deadlock across multiple
engine due to a real preemption event reordering the no-preemption
WAITs. To resolve this issue we currently promote all requests to WAIT
on unsubmission, however this interferes with the timeslicing
requirement that we do not apply any implicit promotion that will defeat
the round-robin timeslice list. (If we automatically promote the active
request it will go back to the head of the queue and not the tail!)
So we need implicit promotion to prevent reordering around semaphores
where we are not allowed to preempt, and we must avoid implicit
promotion on unsubmission. So instead of at unsubmit, if we apply that
implicit promotion on adding the dependency, we avoid the semaphore
deadlock and we also reduce the gains made by the promotion for user
space waiting. Furthermore, by keeping the earlier dependencies at a
higher level, we reduce the search space for timeslicing without
altering runtime scheduling too badly (no dependencies at all will be
assigned a higher priority for rrul).
v2: Limit the bump to external edges (as originally intended) i.e.
between contexts and out to the user.
Chris Wilson [Fri, 17 May 2019 10:22:24 +0000 (11:22 +0100)]
drm/i915/dp: Initialise locals for static analysis
Just to squelch an smatch warning that doesn't see the with_() being
taken unconditionally:
drivers/gpu/drm/i915//intel_dp.c:230 intel_dp_get_fia_supported_lane_count() error: uninitialized symbol 'lane_info'.
drivers/gpu/drm/i915//intel_dp.c:5338 intel_digital_port_connected() error: uninitialized symbol 'is_connected'.
Chris Wilson [Wed, 15 May 2019 13:00:49 +0000 (14:00 +0100)]
drm/i915: Truly bump ready tasks ahead of busywaits
In commit b7404c7ecb38 ("drm/i915: Bump ready tasks ahead of
busywaits"), I tried cutting a corner in order to not install a signal
for each of our dependencies, and only listened to requests on which we
were intending to busywait. The compromise that was made was that
instead of then being able to promote the request with a full
NOSEMAPHORE like its non-busywaiting brethren, as we had not ensured we
had cleared the semaphore chain, we settled for only using the NEWCLIENT
boost. With an over saturated system with multiple NEWCLIENTS in flight
at any time, this was found to be an inadequate promotion and left us
with a much poorer scheduling order than prior to using semaphores.
The outcome of this patch, is that all requests have NOSEMAPHORE
priority when they have no dependencies and are ready to run and not
busywait, restoring the pre-semaphore ordering on saturated systems.
We can demonstrate the effect of poor scheduling order by oversaturating
the system using gem_wsim on a system with multiple vcs engines
(i.e running the same workloads across more clients than required for
peak throughput, e.g. media_load_balance_17i7.wsim -c4 -b context):
Imre Deak [Thu, 9 May 2019 17:34:46 +0000 (20:34 +0300)]
drm/i915: Assert that TypeC ports are not used for eDP
Add an assert that we don't use TypeC ports for eDP. That may in theory
be possible on TypeC legacy ports, but I'm not sure if that's a
practical scenario, so let's deal with that only if there's a use case.
Adding support for that wouldn't be too difficult, since TypeC mode
switching is not possible on TypeC legacy ports.
Imre Deak [Thu, 9 May 2019 17:34:45 +0000 (20:34 +0300)]
drm/i915: Avoid taking the PPS lock for non-eDP/VLV/CHV
On ICL we have to make sure that we enable the AUX power domain in a
controlled way (corresponding to the port's actual TypeC mode). Since
the PPS lock - which takes an AUX power ref - is only needed on
eDP on all platforms and eDP/DP on VLV/CHV avoid taking it in all
other cases.
v2:
- Clarify commit log about the condition for taking the PPS lock.
(Ville)
Imre Deak [Thu, 9 May 2019 17:34:44 +0000 (20:34 +0300)]
drm/i915: Replace use of PLLS power domain with DISPLAY_CORE domain
There isn't a separate power domain specific to PLLs. When programming
them we require the same power domain to be enabled which is needed when
accessing other display core parts (not specific to any
pipe/port/transcoder). This corresponds to the DISPLAY_CORE domain added
previously in this patchset, so use that instead to save bits in the
power domain mask.
Imre Deak [Thu, 9 May 2019 17:34:43 +0000 (20:34 +0300)]
drm/i915: Remove the unneeded AUX power ref from intel_dp_hpd_pulse()
The power get/put was added in
commit 1c767b339b39 ("drm/i915: take display port power domain in DP HPD handler")
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Aug 18 14:42:42 2014 +0300
to account for the HW access in ibx_digital_port_connected(). This
latter call was in turn removed in
commit 7d23e3c37bb3 ("drm/i915: Cleaning up intel_dp_hpd_pulse")
Author: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Date: Wed Mar 30 18:05:23 2016 +0530
after which we didn't actually need the power reference.
One way we are accessing the HW during HPD pulse handling is via DP AUX
transfers, but the transfer function takes its own reference, so doesn't
need the reference in intel_dp_hpd_pulse().
Imre Deak [Thu, 9 May 2019 17:34:42 +0000 (20:34 +0300)]
drm/i915: Remove the unneeded AUX power ref from intel_dp_detect()
We don't need the AUX power for the whole duration of the detect, only
when we're doing AUX transfers. The AUX transfer function takes its own
reference on the AUX power domain already. The two places during detect
which access display core registers (not specific to a
pipe/port/transcoder) only need the power domain that is required for
that access. That power domain is equivalent to the device global power
domain on most platforms (enabled whenever we hold a runtime PM
reference) except on CHV/VLV where it's equivalent to the display power
well.
Add a new power domain that reflects the above, and use this at the two
spots accessing registers. With that we can avoid taking the AUX
reference for the whole duration of the detect function.
Put the domains asynchronously to avoid the unneeded on-off-on toggling.
Also adapt the idea from with_intel_runtime_pm et al. for making it easy
to write short sequences where a display power ref is needed.
Imre Deak [Thu, 9 May 2019 17:34:40 +0000 (20:34 +0300)]
drm/i915: Disable power asynchronously during DP AUX transfers
In a follow-up patch we will restrict holding the reference on the AUX
power domain to the AUX transfer function. To avoid the unnecessary
on-off-on power togglings drop the reference asynchronously.
There is no reason we couldn't do this in general and also put the
reference asynchronously in pps_unlock(); but that's a separate change
that can be done as a follow-up.
Imre Deak [Mon, 13 May 2019 19:25:33 +0000 (22:25 +0300)]
drm/i915: Add support for asynchronous display power disabling
By disabling a power domain asynchronously we can restrict holding a
reference on that power domain to the actual code sequence that
requires the power to be on for the HW access it's doing, by also
avoiding unneeded on-off-on togglings of the power domain (since the
disabling happens with a delay).
One benefit is potential power saving due to the following two reasons:
1. The fact that we will now be holding the reference only for the
necessary duration by the end of the patchset. While simply not
delaying the disabling has the same benefit, it has the problem that
frequent on-off-on power switching has its own power cost (see the 2.
point below) and the debug trace for power well on/off events will
cause a lot of dmesg spam (see details about this further below).
2. Avoiding the power cost of freuqent on-off-on power switching. This
requires us to find the optimal disabling delay based on the measured
power cost of on->off and off->on switching of each power well vs.
the power of keeping the given power well on.
In this patchset I'm not providing this optimal delay for two
reasons:
a) I don't have the means yet to perform the measurement (with high
enough signal-to-noise ratio, or with the help of an energy
counter that takes switching into account). I'm currently looking
for a way to measure this.
b) Before reducing the disabling delay we need an alternative way for
debug tracing powerwell on/off events. Simply avoiding/throttling
the debug messages is not a solution, see further below.
Note that even in the case where we can't measure any considerable
power cost of frequent on-off switching of powerwells, it still would
make sense to do the disabling asynchronously (with 0 delay) to avoid
blocking on the disabling. On VLV I measured this disabling time
overhead to be 1ms on average with a worst case of 4ms.
In the case of the AUX power domains on ICL we would also need to keep
the sequence where we hold the power reference short, the way it would
be by the end of this patchset where we hold it only for the actual AUX
transfer. Anything else would make the locking we need for ICL TypeC
ports (whenever we hold a reference on any AUX power domain) rather
problematic, adding for instance unnecessary lockdep dependencies to
the required TypeC port lock.
I chose the disabling delay to be 100msec for now to avoid the unneeded
toggling (and so not to introduce dmesg spamming) in the DP MST sideband
signaling code. We could optimize this delay later, once we have the
means to measure the switching power cost (see above).
Note that simply removing/throttling the debug tracing for power well
on/off events is not a solution. We need to know the exact spots of
these events and cannot rely only on incorrect register accesses caught
(due to not holding a wakeref at the time of access). Incorrect
powerwell enabling/disabling could lead to other problems, for instance
we need to keep certain powerwells enabled for the duration of modesets
and AUX transfers.
v2:
- Clarify the commit log parts about power cost measurement and the
problem of simply removing/throttling debug tracing. (Chris)
- Optimize out local wakeref vars at intel_runtime_pm_put_raw() and
intel_display_power_put_async() call sites if
CONFIG_DRM_I915_DEBUG_RUNTIME_PM=n. (Chris)
- Rebased on v2 of the wakeref w/o power-on guarantee patch.
- Add missing docbook headers.
v3:
- Checkpatch spelling/missing-empty-line fix.
v4:
- Fix unintended local wakeref var optimization when using
call-arguments with side-effects, by using inline funcs instead of
macros. In this patch in particular this will fix the
intel_display_power_grab_async_put_ref()->intel_runtime_pm_put_raw()
call).
No size change in practice (would be the same disregarding the
corresponding change in intel_display_power_grab_async_put_ref()):
$ size i915-macro.ko
text data bss dec hex filename 2455190 105890 10272 2571352 273c58 i915-macro.ko
$ size i915-inline.ko
text data bss dec hex filename 2455195 105890 10272 2571357 273c5d i915-inline.ko
Kudos to Stan for reporting the raw-wakeref WARNs this issue caused. His
config has CONFIG_DRM_I915_DEBUG_RUNTIME_PM=n, which I didn't retest
after v1, and we are also not testing this config in CI.
Now tested both with CONFIG_DRM_I915_DEBUG_RUNTIME_PM=y/n on ICL,
connecting both Chamelium and regular DP, HDMI sinks.
Imre Deak [Thu, 9 May 2019 17:34:38 +0000 (20:34 +0300)]
drm/i915: Verify power domains state during suspend in all cases
There is no reason why we couldn't verify the power domains state during
suspend in all cases, so do that. I overlooked this when originally
adding the check.
Imre Deak [Thu, 9 May 2019 17:34:37 +0000 (20:34 +0300)]
drm/i915: Force printing wakeref tacking during pm_cleanup
Make sure we print and drop the wakeref tracking info during pm_cleanup
even if there are wakeref holders (either raw-wakeref or wakelock
holders). Dropping the wakeref tracking means that a late put on the ref
will WARN since the wakeref will be unknown, but that is rightly so,
since the put is late and we want to catch that case.
Imre Deak [Thu, 9 May 2019 17:34:36 +0000 (20:34 +0300)]
drm/i915: Add support for tracking wakerefs w/o power-on guarantee
It's useful to track runtime PM refs that don't guarantee a device
power-on state to the rest of the driver. One such case is holding a
reference that will be put asynchronously, during which normal users
without their own reference shouldn't access the HW. A follow-up patch
will add support for disabling display power domains asynchronously
which needs this.
For this we can split wakeref_count into a low half-word tracking
all references (raw-wakerefs) and a high half-word tracking
references guaranteeing a power-on state (wakelocks).
Follow-up patches will make use of the API added here.
While at it add the missing docbook header for the unchecked
display-power and runtime_pm put functions.
No functional changes, except for printing leaked raw-wakerefs
and wakelocks separately in intel_runtime_pm_cleanup().
v2:
- Track raw wakerefs/wakelocks in the low/high half-word of
wakeref_count, instead of adding a new counter. (Chris)
v3:
- Add a struct_member(T, m) helper instead of open-coding it. (Chris)
- Checkpatch indentation formatting fix.
Imre Deak [Fri, 10 May 2019 14:02:55 +0000 (17:02 +0300)]
drm/i915/icl: More workaround for port F detection due to broken VBTs
Add another ICL-Y PCIID that proved to have only 5 ports to the
corresponding PCIID list.
Meanwhile I'm trying to get a complete list of all PCIIDs with less than
6 ports and/or get a VBT fix to mark these ports non-existent, but until
then the only way is to go one-by-one.
This fixes the following error on machines with less than 6 port:
[drm:intel_power_well_enable [i915]] enabling AUX F
------------[ cut here ]------------
WARN_ON(intel_wait_for_register(&dev_priv->uncore, regs->driver, (0x1 << ((pw_idx) * 2)), (0x1 << ((pw_idx) * 2)), 1))
Ramalingam C [Mon, 13 May 2019 13:35:04 +0000 (19:05 +0530)]
drm/hdcp: drm_hdcp_request_srm() as static
Below Sparsh warnings are fixed.
Commit: drm: revocation check at drm subsystem
+drivers/gpu/drm/drm_hdcp.c:235:6: warning: symbol
'drm_hdcp_request_srm' was not declared. Should it be static?
+drivers/gpu/drm/drm_hdcp.c:27:3: warning: symbol 'srm_data' was not
declared. Should it be static?
+drivers/gpu/drm/drm_hdcp.c:317:5: warning: symbol 'drm_setup_hdcp_srm'
was not declared. Should it be static?
+drivers/gpu/drm/drm_hdcp.c:327:6: warning: symbol
'drm_teardown_hdcp_srm' was not declared. Should it be static?
Chris Wilson [Mon, 13 May 2019 12:01:02 +0000 (13:01 +0100)]
drm/i915: Check for no-op priority changes first
In all likelihood, the priority and node are already in the CPU cache
and by checking them first, we can avoid having to chase the
*request->hwsp for the current breadcrumb.
Ville Syrjälä [Thu, 25 Apr 2019 16:29:06 +0000 (19:29 +0300)]
drm/i915: Add readout and state check for pch_pfit.force_thru
Convert the HSW pch_pfit.force_thru to a proper state variable
with readout and accompanying pipe conf check. Makes the logic
a bit more straightforward, and hopefully prevents some
breakage in the future.
'force_thru' is probably not the best name for this, but I
didn't manage to come up with anything better either, so I
left it alone.
Ville Syrjälä [Thu, 25 Apr 2019 16:29:05 +0000 (19:29 +0300)]
drm/i915: Fix fastset vs. pfit on/off on HSW EDP transcoder
On HSW the pipe A panel fitter lives inside the display power well,
and the input MUX for the EDP transcoder needs to be configured
appropriately to route the data through the power well as needed.
Changing the MUX setting is not allowed while the pipe is active,
so we need to force a full modeset whenever we need to change it.
Currently we may end up doing a fastset which won't change the
MUX settings, but it will drop the power well reference, and that
kills the pipe.
Cc: stable@vger.kernel.org Cc: Hans de Goede <hdegoede@redhat.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Fixes: d19f958db23c ("drm/i915: Enable fastset for non-boot modesets.") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190425162906.5242-1-ville.syrjala@linux.intel.com Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Daniel Drake [Tue, 23 Apr 2019 09:28:10 +0000 (17:28 +0800)]
drm/i915/fbc: disable framebuffer compression on GeminiLake
On many (all?) the Gemini Lake systems we work with, there is frequent
momentary graphical corruption at the top of the screen, and it seems
that disabling framebuffer compression can avoid this.
The ticket was reported 6 months ago and has already affected a
multitude of users, without any real progress being made. So, lets
disable framebuffer compression on GeminiLake until a solution is found.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108085 Fixes: fd7d6c5c8f3e ("drm/i915: enable FBC on gen9+ too") Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: <stable@vger.kernel.org> # v4.11+ Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190423092810.28359-1-jian-hong@endlessm.com
Ramalingam C [Tue, 7 May 2019 16:27:38 +0000 (21:57 +0530)]
drm: revocation check at drm subsystem
On every hdcp revocation check request SRM is read from fw file
/lib/firmware/display_hdcp_srm.bin
SRM table is parsed and stored at drm_hdcp.c, with functions exported
for the services for revocation check from drivers (which
implements the HDCP authentication)
This patch handles the HDCP1.4 and 2.2 versions of SRM table.
v2:
moved the uAPI to request_firmware_direct() [Daniel]
v3:
kdoc added. [Daniel]
srm_header unified and bit field definitions are removed. [Daniel]
locking improved. [Daniel]
vrl length violation is fixed. [Daniel]
v4:
s/__swab16/be16_to_cpu [Daniel]
be24_to_cpu is done through a global func [Daniel]
Unused variables are removed. [Daniel]
unchecked return values are dropped from static funcs [Daniel]
Chris Wilson [Wed, 8 May 2019 11:24:52 +0000 (12:24 +0100)]
drm/i915: Seal races between async GPU cancellation, retirement and signaling
Currently there is an underlying assumption that i915_request_unsubmit()
is synchronous wrt the GPU -- that is the request is no longer in flight
as we remove it. In the near future that may change, and this may upset
our signaling as we can process an interrupt for that request while it
is no longer in flight.
Hence in the time it took us to drop the lock to signal the request, a
preemption event may have occurred and re-queued the request. In the
process, that request would have seen I915_FENCE_FLAG_SIGNAL clear and
so reused the rq->signal_link that was in use on CPU0, leading to bad
pointer chasing in intel_engine_breadcrumbs_irq.
A related issue was that if someone started listening for a signal on a
completed but no longer in-flight request, we missed the opportunity to
immediately signal that request.
Furthermore, as intel_contexts may be immediately released during
request retirement, in order to be entirely sure that
intel_engine_breadcrumbs_irq may no longer dereference the intel_context
(ce->signals and ce->signal_link), we must wait for irq spinlock.
In order to prevent the race, we use a bit in the fence.flags to signal
the transfer onto the signal list inside intel_engine_breadcrumbs_irq.
For simplicity, we use the DMA_FENCE_FLAG_SIGNALED_BIT as it then
quickly signals to any outside observer that the fence is indeed signaled.
v2: Sketch out potential dma-fence API for manual signaling
v3: And the test_and_set_bit()
Chris Wilson [Wed, 8 May 2019 08:06:25 +0000 (09:06 +0100)]
drm/i915/hangcheck: Replace hangcheck.seqno with RING_HEAD
After realising we need to sample RING_START to detect context switches
from preemption events that do not allow for the seqno to advance, we
can also realise that the seqno itself is just a distance along the ring
and so can be replaced by sampling RING_HEAD.
v2: Bonus comment for the mystery separate CS_STALL before MI_USER_INTERRUPT
Chris Wilson [Wed, 8 May 2019 11:52:45 +0000 (12:52 +0100)]
drm/i915: Reboot CI if forcewake fails
If the HW fails to ack a change in forcewake status, the machine is as
good as dead -- it may recover, but in reality it missed the mmio
updates and is now in a very inconsistent state. If it happens, we can't
trust the CI results (or at least the fails may be genuine but due to
the HW being dead and not the actual test!) so reboot the machine (CI
checks for a kernel taint in between each test and reboots if the
machine is tainted).
Aditya Swarup [Tue, 7 May 2019 18:18:56 +0000 (11:18 -0700)]
drm/i915/icl: Fix setting 10 bit deep color mode
There is a bug in hdmi_deep_color_possible() - we compare pipe_bpp
<= 8*3 which returns true every time for hdmi_deep_color_possible 12 bit
deep color mode test in intel_hdmi_compute_config().(Even when the
requested color mode is 10 bit through max bpc property)
Comparing pipe_bpp with bpc * 3 takes care of this condition where
requested max bpc is 10 bit, so hdmi_deep_color_possible with 12 bit
returns false when requested max bpc is 10.(Ville)
v2:Add suggested by Ville Syrjälä
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Aditya Swarup <aditya.swarup@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Clinton Taylor <Clinton.A.Taylor@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190507181856.16091-1-aditya.swarup@intel.com
Ville Syrjälä [Mon, 6 May 2019 15:26:27 +0000 (18:26 +0300)]
drm/i915: Kill PCH_KBP
For us KBP is 100% identical to SPT. Kill the redundant enum
value. Also bspec doesn't talk about KBP either, so this might
avoid some confusion when cross checking the code against the
spec.
Chris Wilson [Tue, 7 May 2019 12:25:44 +0000 (13:25 +0100)]
drm/i915: Only reschedule the submission tasklet if preemption is possible
If we couple the scheduler more tightly with the execlists policy, we
can apply the preemption policy to the question of whether we need to
kick the tasklet at all for this priority bump.
v2: Rephrase it as a core i915 policy and not an execlists foible.
v3: Pull the kick together.
Chris Wilson [Tue, 7 May 2019 12:11:08 +0000 (13:11 +0100)]
drm/i915: Stop spinning for DROP_IDLE (debugfs/i915_drop_caches)
If the user is racing a call to debugfs/i915_drop_caches with ongoing
submission from another thread/process, we may never end up idling the
GPU and be uninterruptibly spinning in debugfs/i915_drop_caches trying
to catch an idle moment.
Just flush the work once, that should be enough to park the system under
correct conditions. Outside of those we either have a driver bug or the
user is racing themselves. Sadly, because the user may be provoking the
unwanted situation we can't put a warn here to attract attention to a
probable bug.
Chris Wilson [Tue, 7 May 2019 12:11:07 +0000 (13:11 +0100)]
drm/i915: Cancel retire_worker on parking
Replace the racy continuation check within retire_work with a definite
kill-switch on idling. The race was being exposed by gem_concurrent_blit
where the retire_worker would be terminated too early leaving us
spinning in debugfs/i915_drop_caches with nothing flushing the
retirement queue.
Although that the igt is trying to idle from one child while submitting
from another may be a contributing factor as to why it runs so slowly...
v2: Use the non-sync version of cancel_delayed_work(), we only need to
stop it from being scheduled as we independently check whether now is
the right time to be parking.
Chris Wilson [Tue, 7 May 2019 12:11:06 +0000 (13:11 +0100)]
drm/i915: Remove delay for idle_work
The original intent for the delay before running the idle_work was to
provide a hysteresis to avoid ping-ponging the device runtime-pm. Since
then we have also pulled in some memory management and general device
management for parking. But with the inversion of the wakeref handling,
GEM is no longer responsible for the wakeref and by the time we call the
idle_work, the device is asleep. It seems appropriate now to drop the
delay and just run the worker immediately to flush the cached GEM state
before sleeping.
Chris Wilson [Tue, 7 May 2019 12:11:05 +0000 (13:11 +0100)]
drm/i915: Flush the switch-to-kernel-context harder for DROP_IDLE
To complete the idle worker, we must complete 2 passes of wait-for-idle.
At the end of the first pass, we queue a switch-to-kernel-context and
may only idle after waiting for its completion. Speed up the flush_work
by doing the wait explicitly, which then allows us to remove the
unbounded loop trying to complete the flush_work in the next patch.
Clinton Taylor [Mon, 29 Apr 2019 23:08:11 +0000 (16:08 -0700)]
drm/i915/icl: Set GCP_COLOR_INDICATION only for 10/12 bit deep color
v2: Fix commit msg to reflect why issue occurs(Jani)
Set GCP_COLOR_INDICATION only when we set 10/12 bit deep color.
Changing settings from 10/12 bit deep color to 8 bit(& vice versa)
doesn't work correctly using xrandr max bpc property. When we
connect a monitor which supports deep color, the highest deep color
setting is selected; which sets GCP_COLOR_INDICATION. When we change
the setting to 8 bit color, we still set GCP_COLOR_INDICATION which
doesn't allow the switch back to 8 bit color.
v3,4: Add comments & drop changes in intel_hdmi_compute_config(Ville)
Since HSW+, GCP_COLOR_INDICATION is not required for 8bpc.
Drop the changes in intel_hdmi_compute_config as desired_bpp
is needed to change values for pipe_bpp based on bw_constrained flag.
v5: Fix missing logical && in condition for setting GCP_COLOR_INDICATION.
v6: Fix comment formatting (Ville)
v7: Add reviewed by Ville
v8: Set GCP_COLOR_INDICATION based on spec:
For Gen 7.5 or later platforms, indicate color depth only for deep
color modes. Bspec: 8135,7751,50524
Pre DDI platforms, indicate color depth if deep color is supported
by sink. Bspec: 7854
Exception: CHERRYVIEW behaves like Pre DDI platforms.
Bspec: 15975
Check pipe_bpp is less than bpp * 3 in hdmi_deep_color_possible,
to not set 12 bit deep color for every modeset. This fixes the issue
where 12 bit color was selected even when user selected 10 bit.(Ville)
v9: Maintain a consistent behavior for all platforms and support
GCP_COLOR_INDICATION only when we are in deep color mode. Remove
hdmi_sink_is_deep_color() - no longer needed as checking pipe_bpp > 24
takes care of the deep color mode scenario.
Separate patch for fixing switch from 12 bit to 10 bit deep color
mode.
Co-developed-by: Aditya Swarup <aditya.swarup@intel.com> Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com> Signed-off-by: Aditya Swarup <aditya.swarup@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190429230811.9983-1-aditya.swarup@intel.com
Chris Wilson [Fri, 3 May 2019 11:52:15 +0000 (12:52 +0100)]
drm/i915: Assert the local engine->wakeref is active
Due to the asynchronous tasklet and recursive GT wakeref, it may happen
that we submit to the engine (underneath it's own wakeref) prior to the
central wakeref being marked as taken. Switch to checking the local wakeref
for greater consistency.
Chris Wilson [Fri, 3 May 2019 11:52:14 +0000 (12:52 +0100)]
drm/i915: Prefer checking the wakeref itself rather than the counter
The counter goes to zero at the start of the parking cycle, but the
wakeref itself is held until the end. Likewise, the counter becomes one
at the end of the unparking, but the wakeref is taken first. If we check
the wakeref instead of the counter, we include the unpark/unparking time
as intel_wakeref_is_active(), and do not spuriously declare inactive if
we fail to park (i.e. the parking and wakeref drop is postponed).
Chris Wilson [Fri, 3 May 2019 15:22:14 +0000 (16:22 +0100)]
drm/i915: Assert breadcrumbs are correctly ordered in the signal handler
Inside the signal handler, we expect the requests to be ordered by their
breadcrumb such that no later request may be complete if we find an
earlier incomplete. Add an assert to check that the next breadcrumb
should not be logically before the current.
v2: Move the overhanging line into its own function and reuse it after
doing the insertion.
Chris Wilson [Fri, 3 May 2019 14:02:39 +0000 (15:02 +0100)]
drm/i915: Acquire the signaler's timeline HWSP last
Acquiring the signaler's timeline takes an active reference to their
HWSP that we would like to avoid if possible, so take it after
performing all of our allocations required to set up the fencing. The
acquisition also provides the final check that the target has not
already signaled allowing us to avoid the semaphore at the last moment.
Ville Syrjälä [Fri, 3 May 2019 19:31:43 +0000 (22:31 +0300)]
drm/i915: Move the hsw/bdw pc8 code to intel_runtime_pm.c
hsw_enable_pc8()/hsw_disable_pc8() are more less equivalent to
the display core init/unit functions of later platforms. Relocate
the hsw/bdw code into intel_runtime_pm.c so that it sits next to
its cousins.
Ville Syrjälä [Fri, 3 May 2019 17:38:07 +0000 (20:38 +0300)]
drm/i915: Move w/a 0477/WaDisableIPC:skl into intel_init_ipc()
Move the w/a to disable IPC on SKL closer to the actual code
that implements IPS. Otherwise I just end up confused as to
what is excluding SKL from considerations.
IMO this makes more sense anyway since the hw does have the
feature, we're just not supposed to use it.
And this also makes us actually disable IPC in case eg. the
BIOS enabled it when it shouldn't have.
Chris Wilson [Sat, 4 May 2019 07:07:07 +0000 (08:07 +0100)]
drm/i915: Disable semaphore busywaits on saturated systems
Asking the GPU to busywait on a memory address, perhaps not unexpectedly
in hindsight for a shared system, leads to bus contention that affects
CPU programs trying to concurrently access memory. This can manifest as
a drop in transcode throughput on highly over-saturated workloads.
The only clue offered by perf, is that the bus-cycles (perf stat -e
bus-cycles) jumped by 50% when enabling semaphores. This corresponds
with extra CPU active cycles being attributed to intel_idle's mwait.
This patch introduces a heuristic to try and detect when more than one
client is submitting to the GPU pushing it into an oversaturated state.
As we already keep track of when the semaphores are signaled, we can
inspect their state on submitting the busywait batch and if we planned
to use a semaphore but were too late, conclude that the GPU is
overloaded and not try to use semaphores in future requests. In
practice, this means we optimistically try to use semaphores for the
first frame of a transcode job split over multiple engines, and fail if
there are multiple clients active and continue not to use semaphores for
the subsequent frames in the sequence. Periodically, we try to
optimistically switch semaphores back on whenever the client waits to
catch up with the transcode results.
With 1 client, on Broxton J3455, with the relative fps normalized by %cpu:
x no semaphores
+ drm-tip
* patched
+------------------------------------------------------------------------+
| * |
| *+ |
| **+ |
| **+ x |
| x * +**+ x |
| x x * * +***x xx |
| x x * * *+***x *x |
| x x* + * * *****x *x x |
| + x xx+x* + *** * ********* x * |
| + x xx+x* * *** +** ********* xx * |
| * + ++++* + x*x****+*+* ***+*************+x* * |
|*+ +** *+ + +* + *++****** *xxx**********x***+*****************+*++ *|
| |__________A_____M_____| |
| |_______________A____M_________| |
| |____________A___M________| |
+------------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 120 2.60475 3.50941 3.31123 3.2143953 0.21117399
+ 120 2.3826 3.57077 3.25101 3.1414161 0.28146407
Difference at 95.0% confidence
-0.0729792 +/- 0.0629585
-2.27039% +/- 1.95864%
(Student's t, pooled s = 0.248814)
* 120 2.35536 3.66713 3.2849 3.2059917 0.24618565
No difference proven at 95.0% confidence
Indicating that we've recovered the regression from enabling semaphores
on this saturated setup, with a hint towards an overall improvement.
Very similar, but of smaller magnitude, results are observed on both
Skylake(gt2) and Kabylake(gt4). This may be due to the reduced impact of
bus-cycles, where we see a 50% hit on Broxton, it is only 10% on the big
core, in this particular test.
One observation to make here is that for a greedy client trying to
maximise its own throughput, using semaphores is the right choice. It is
only the holistic system-wide view that semaphores of one client
impacts another and reduces the overall throughput where we would choose
to disable semaphores.
The most noticeable negactive impact this has is on the no-op
microbenchmarks, which are also very notable for having no cpu bus load.
In particular, this increases the runtime and energy consumption of
gem_exec_whisper.
Ville Syrjälä [Thu, 2 May 2019 20:06:07 +0000 (23:06 +0300)]
drm/i915: Allow ICL pipe "HDR mode" when the cursor is visible
Turns out the cursor is compatible with the pipe "HDR mode". It's
only the actual SDR planes that get entirely bypassed during
blending. So let's ignore the cursor when checking if we have
any planes active that aren't HDR compatible. This fixes the
regressions in the kms_cursor_crc and kms_plane_cursor tests.
Cc: Uma Shankar <uma.shankar@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110579 Fixes: 09b25812db10 ("drm/i915: Enable pipe HDR mode on ICL if only HDR planes are used") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190502200607.14504-2-ville.syrjala@linux.intel.com Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Ville Syrjälä [Thu, 2 May 2019 20:06:06 +0000 (23:06 +0300)]
drm/i915: Move the PIPEMISC write the correct place
I fumbled the PIPEMISC write into the wrong place. It only gets
called for fastsets, but since value needs to be updated based on
the set of active planes it needs to be done for all plane updates.
Move it to the correct spot.
The symptoms include SDR planes never showing up if a previous
modeset/fastset left the pipe in HDR mode. This was immediately
obvious when running the kms_plane pixel format tests. Unfortunately
the test didn't realize it was scanning out pure black all the time
and declared success anyway.
Cc: Uma Shankar <uma.shankar@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Fixes: 09b25812db10 ("drm/i915: Enable pipe HDR mode on ICL if only HDR planes are used") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190502200607.14504-1-ville.syrjala@linux.intel.com Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Chris Wilson [Wed, 1 May 2019 11:45:36 +0000 (12:45 +0100)]
drm/i915: Delay semaphore submission until the start of the signaler
Currently we submit the semaphore busywait as soon as the signaler is
submitted to HW. However, we may submit the signaler as the tail of a
batch of requests, and even not as the first context in the HW list,
i.e. the busywait may start spinning far in advance of the signaler even
starting.
If we wait until the request before the signaler is completed before
submitting the busywait, we prevent the busywait from starting too
early, if the signaler is not first in submission port.
To handle the case where the signaler is at the start of the second (or
later) submission port, we will need to delay the execution callback
until we know the context is promoted to port0. A challenge for later.
Chris Wilson [Wed, 1 May 2019 11:45:28 +0000 (12:45 +0100)]
drm/i915/hangcheck: Track context changes
Given sufficient preemption, we may see a busy system that doesn't
advance seqno while performing work across multiple contexts, and given
sufficient pathology not even notice a change in ACTHD. What does change
between the preempting contexts is their RING, so take note of that and
treat a change in the ring address as being an indication of forward
progress.
Chris Wilson [Thu, 2 May 2019 15:00:24 +0000 (16:00 +0100)]
drm/i915: Leave engine parking to the engines
Drop the check in GEM parking that the engines were already parked. The
intention here was that before we dropped the GT wakeref, we were sure
that no more interrupts could be raised -- however, we have already
dropped the wakeref by this point and the warning is no longer valid.
Chris Wilson [Fri, 3 May 2019 08:09:42 +0000 (09:09 +0100)]
drm/i915/execlists: Flush the tasklet on parking
Tidy up the cleanup sequence by always ensure that the tasklet is
flushed on parking (before we cleanup). The parking provides a
convenient point to ensure that the backend is truly idle.
v2: Do the full check for idleness before parking, to be sure we flush
any residual interrupt.
Chris Wilson [Thu, 2 May 2019 20:30:09 +0000 (21:30 +0100)]
drm/i915/guc: Fix runtime suspend
We are not allowed to rpm_get() inside the runtime-suspend callback, so
split the intel_uc_suspend() into the core that assumes the caller holds
the wakeref (intel_uc_runtime_suspend), and one that acquires the wakeref
as necessary (intel_uc_suspend).
Reported-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Fixes: 79ffac8599c4 ("drm/i915: Invert the GEM wakeref hierarchy") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190502203009.15727-1-chris@chris-wilson.co.uk
Jani Nikula [Thu, 2 May 2019 15:02:47 +0000 (18:02 +0300)]
drm/i915: extract intel_gmbus.h from i915_drv.h and rename intel_i2c.c
It used to be handy that we only had a couple of headers, but over time
i915_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
While at it, rename intel_i2c.c to intel_gmbus.c and the functions to
intel_gmbus_*.
Jani Nikula [Thu, 2 May 2019 15:02:43 +0000 (18:02 +0300)]
drm/i915: extract i915_debugfs.h from i915_drv.h
It used to be handy that we only had a couple of headers, but over time
i915_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
Jani Nikula [Thu, 2 May 2019 15:02:42 +0000 (18:02 +0300)]
drm/i915: extract intel_acpi.h from i915_drv.h
It used to be handy that we only had a couple of headers, but over time
i915_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
Jani Nikula [Thu, 2 May 2019 15:02:41 +0000 (18:02 +0300)]
drm/i915: extract intel_lpe_audio.h from i915_drv.h
It used to be handy that we only had a couple of headers, but over time
i915_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
Jani Nikula [Thu, 2 May 2019 15:02:40 +0000 (18:02 +0300)]
drm/i915: extract intel_dpio_phy.h from i915_drv.h
It used to be handy that we only had a couple of headers, but over time
i915_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
Imre Deak [Thu, 2 May 2019 10:17:54 +0000 (13:17 +0300)]
drm/i915: Tune down WARN about incorrect VBT TC legacy flag
Looks like VBT contains again the wrong information about a port's TypeC
legacy vs. DP-alt/TBT-alt type. There is no further issues after we
notice this and fix it up, so tune down the WARN to be a a DRM_ERROR.
This also avoids CI tainting the kernel and stopping the test run.
Imre Deak [Thu, 25 Apr 2019 18:52:52 +0000 (21:52 +0300)]
drm/i915/icl: Factor out combo PHY lane power setup helper
Factor out the combo PHY lane power configuration code to a separate
helper; it will be also needed by the next patch adding the same
configuration for DDI ports.
Add support for DDI ports and lane reversal as preparation for the next
patch.
The PWR_DOWN_LN_1 value is unspecified in the BSpec register description
so remove it.
v2:
- Fix up the wrong assumption that the encodings are the same for DDI
and DSI ports. (Jani)
v3:
- Use intel_ instead of icl_ prefix. (Jani)
- Add required headers to intel_combo_phy.h after the upstream header
refactoring.
Ville Syrjälä [Tue, 30 Apr 2019 14:29:01 +0000 (17:29 +0300)]
drm/i915: hsw+ audio regs are per-transocder
s/pipe/transcoder/ when dealing with hsw+ audio registers. This
won't actually make any real difference since there is no audio
on the EDP transcoder. But this should avoid a bit of confusion
when cross checking against the spec.
Ville Syrjälä [Tue, 30 Apr 2019 14:29:00 +0000 (17:29 +0300)]
drm/i915: Don't skip audio enable if ELD is bogus
We've already committed to enabling audio when intel_audio_codec_enable()
is called. We can't back out even if the ELD has turned sour in the
meantime. So just spew some debug log and plow ahead. Otherwise the
state checker gets unhappy when audio isn't enabled when it is
expected to be.
I suppose we really ought to precompute the ELD as well, but
let's just toss in a FIXME for the future.
Currently due to regression CI machine displays show corrupt picture.
Problem is when CDCLK is as low as 79200, picture gets unstable, while
DSI and DE pll values were confirmed to be correct. Limiting to 158400
as agreed with Ville.
We could not come up with any better solution yet, as PLL divider values
both for MIPI(DSI PLL) and CDCLK(DE PLL) are correct, however seems that
due to some boundary conditions, when clocking is too low we get wrong
timings for DSI display. Similar workaround exists for VLV though, so
just took similar condition into use. At least that way GLK platform
will start to be usable again, with current drm-tip.
v2: Fixed commit subject as suggested.
v3: Added generic bugs(crc failures, screen not init
for GLK DSI which might be affected).
v4: Added references tag for bugs affected.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=109267
References: https://bugs.freedesktop.org/show_bug.cgi?id=103184 Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190430125119.7478-1-stanislav.lisovskiy@intel.com
Chris Wilson [Wed, 1 May 2019 13:57:51 +0000 (14:57 +0100)]
drm/i915: Complete both freed-object passes before draining the workqueue
The workqueue code complains viciously if we try to queue more work onto
the queue while attampting to drain it. As we asynchronously free
objects and defer their enqueuing with RCU, it is quite tricky to
quiesce the system before attempting to drain the workqueue. Yet drain
we must to ensure that the worker is idle before unloading the module.
Give the freed object drain 3 whole passes with multiple rcu_barrier()
to give the defer freeing of several levels each protected by RCU and
needing a grace period before its parent can be freed, ultimately
resulting in a GEM object being freed after another RCU period.
A consequence is that it will make module unload even slower.
Chris Wilson [Wed, 1 May 2019 10:32:04 +0000 (11:32 +0100)]
drm/i915: Move the engine->destroy() vfunc onto the engine
Make the engine responsible for cleaning itself up!
This removes the i915->gt.cleanup vfunc that has been annoying the
casual reader and myself for the last several years, and helps keep a
future patch to add more cleanup tidy.
v2: Assert that engine->destroy is set after the backend starts
allocating its own state.
Ville Syrjälä [Fri, 12 Apr 2019 18:30:09 +0000 (21:30 +0300)]
drm/i915: Enable pipe HDR mode on ICL if only HDR planes are used
The pipe has a special HDR mode with higher precision when only
HDR planes are active. Let's use it.
Curiously this fixes the kms_color gamma/degamma tests when
using a HDR plane, which is always the case unless one hacks
the test to use an SDR plane. If one does hack the test to use
an SDR plane it does pass already.
I have no actual explanation how the output after the gamma
LUT can be different between the two modes. The way the tests
are written should mean that the output should be identical
between the solid color vs. the gradient. But clearly that
somehow doesn't hold true for the HDR planes in non-HDR pipe
mode. Anyways, as long as we stick to one type of plane the
test should produce sensible results now.
projects / thirdparty / kernel / stable.git / log
