ramips: remove bogus ralink,mtd-eeprom with offset 0x4
Several devices in mt76x8 subtarget use the following line to set
up wmac in their DTS(I) files:
ralink,mtd-eeprom = <&factory 0x4>
This is strange for several reasons:
- They should use mediatek,mtd-eeprom on this SOC
- The caldata is supposed to start at 0x0
- The parent DTSI mt7628an.dtsi specifies mediatek,mtd-eeprom anyway,
starting from 0x0
- The offset coincides with the default location of the MAC address
in caldata
Based on the comment in b28e94d4bfa1 ("ramips: MiWiFi Nano fixes"),
it looks like the author for this device wanted to actually use
mtd-mac-address instead of ralink,mtd-eeprom. A check on the same
device revealed that actually the MAC address start at offset 4 there,
so the correct caldata offset is 0x0.
Based on these findings, and the fact that the expected location on
this SOC is 0x0, we remove the "ralink,mtd-eeprom = <&factory 0x4>"
statement from all devices in ramips (being only mt7628an anyway).
Thanks to Sungbo Eo for finding and researching this.
Reported-by: Sungbo Eo <mans0n@gorani.run> Fixes: b28e94d4bfa1 ("ramips: MiWiFi Nano fixes") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 09d38a3bc328d122b0d84fcf6bb53d2bce7373b6)
Paul Fertser [Sun, 22 Dec 2019 18:20:57 +0000 (21:20 +0300)]
kernel: ath10k-ct: provide a build variant for small RAM devices
According to many bugreports [0][1][2] the default ath10k-ct kernel
module is unusable on devices with just 64 MiB RAM or with 128 MiB and
dual ath10k cards. The target boards boot but eventually oom-killer
starts to interfere with normal operation, so the current state is
effectively broken.
Since the two patches in question have a performance impact (and
possibly some other unexpected side-effects) a dedicated build variant
is added so that users of the low RAM devices can still benefit from all
the ath10k-ct advantages.
According to testing [3] results, the issue can be experienced even with
"a 256MB device with three radios". Measured performance impact of
implementing small buffers was lowering "the maximum 5 GHz throughput on
an IPQ40xx device without RPS/XPS optimizations from 494/432 Mbit/s for
TCP transfers (download/upload) to 438/343 Mbit/s"
The patches were apparently inspired by QSDK tweaks used by ODMs for the
affected devices.
4327ed4 mkdev: Avoid out of bounds read 9b3eb63 libblkid-tiny: use blkid_probe_set_utf8label for label set c9d0462 libblkid-tiny: adds blkid_probe_set_utf8label support
Sungbo Eo [Fri, 6 Dec 2019 13:49:16 +0000 (22:49 +0900)]
kernel: remove LINUX_4_9 dependency of kmod-dax
This patch resolves recursive dependency warning on a feed package:
$ make defconfig
Collecting package info: done
tmp/.config-package.in:104721:error: recursive dependency detected!
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
tmp/.config-package.in:104721:symbol PACKAGE_nfs-kernel-server depends on NFS_KERNEL_SERVER_V4
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
feeds/packages/net/nfs-kernel-server/Config.in:4:symbol NFS_KERNEL_SERVER_V4 depends on PACKAGE_nfs-kernel-server
#
# configuration written to .config
#
19.07 branch uses kernel 4.14 only, so CONFIG_LINUX_4_9 symbol is not
needed anyway.
Sungbo Eo [Fri, 6 Dec 2019 14:25:48 +0000 (23:25 +0900)]
kernel: fix *-gpio-custom module unloading
Unloading and reloading the modules fails, as platform_device_put() does not
release resources fully.
root@OpenWrt:/# insmod i2c-gpio-custom bus0=0,18,0,5
[ 196.860620] Custom GPIO-based I2C driver version 0.1.1
[ 196.871162] ------------[ cut here ]------------
[ 196.880517] WARNING: CPU: 0 PID: 1365 at fs/sysfs/dir.c:31 0x80112158
[ 196.893431] sysfs: cannot create duplicate filename '/devices/platform/i2c-gpio.0'
...
[ 197.513200] kobject_add_internal failed for i2c-gpio.0 with -EEXIST, don't try to register things with the same name in the same directory.
This patch fixes it by replacing platform_device_put() to
platform_device_unregister().
Fixes: da7740853715 ("i2c-gpio-custom: minor bugfix") Fixes: 3bc81edc70e8 ("package: fix w1-gpio-custom package (closes #6770)") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit a22b7a60d98836343c4f7b9ec0fcae68d9131522)
Rosen Penev [Sun, 17 Nov 2019 21:42:04 +0000 (13:42 -0800)]
cmake: Install host packages to lib instead of lib64
Several CMake packages such as log4cplus and protobuf(-c) install to
lib64 instead of lib on some hosts. This completely breaks rpath linking.
Override it globally to avoid fixing each package individually.
Signed-off-by: Rosen Penev <rosenp@gmail.com> Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
(cherry picked from commit 383abffb1179a142b4c8f86559baad5b24d391c3)
Bjørn Mork [Tue, 19 Nov 2019 13:37:24 +0000 (14:37 +0100)]
adb: fix for SuperSpeed devices
The USB descriptor parsing in adb fails to detect SuperSpeed devices
because of the SuperSpeed Endpoint Companion Descriptor. This
cherry-picks the upstream fix for the problem.
Unfortunately there never were a release with this fix before the
conversion to C++, so upgrading to a newer version isn't an option.
This makes adb work with SuperSpeed devices like the Sierra Wireless
EM7565. Tested and verified.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> Fixes: 863e79f8d554 ("lantiq: add support for kernel 4.9")
(cherry picked from commit 692390225d76de8f2daf582454e74942b82d090a)
Sungbo Eo [Mon, 11 Nov 2019 16:19:03 +0000 (01:19 +0900)]
ramips: fix USB LED for Belkin F9K1109v1
Device support for Belkin F9K1109v1 was added using set_usb_led()
although this was removed in 772b27c20736 ("ramips: set F5D8235 v1
usb led trigger via devicetree").
Use ucidef_set_led_usbport() instead.
Fixes: f2c83532f92c ("ramips: add support for Belkin F9K1109v1") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rephrase commit title and message, backport] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 1f455418ef1ea67fda710e1b86a9e021bb4a2413)
Rafał Miłecki [Thu, 19 Dec 2019 07:40:12 +0000 (08:40 +0100)]
mac80211: brcm: backport 5.5 and 5.6 kernel patches
This update doesn't include: 3b1e0a7bdfee brcmfmac: add support for SAE authentication offload be898fed355e brcmfmac: send port authorized event for FT-802.1X
due to nl80211 dependencies.
Sungbo Eo [Sun, 15 Dec 2019 09:16:55 +0000 (18:16 +0900)]
ath79: migrate LED paths of TL-WDR4300 board
TL-WDR4300 board uses only green LED names in DTSI.
This patch adds migration for them.
The actual LED colors on the devices have been reported to vary
across subrevisions (v1.x). Despite, the USB LEDs on the back might
have different color than the other LEDs on the front.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[extended commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 01d39cd18c4035e362f179548cd2c051aac03042)
Daniel Golle [Mon, 9 Dec 2019 19:12:41 +0000 (20:12 +0100)]
at91: disable legacy PTYs and virtual terminals
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.
Daniel Golle [Mon, 9 Dec 2019 19:07:00 +0000 (20:07 +0100)]
oxnas: disable legacy PTYs and virtual terminals
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.
David Bauer [Fri, 13 Dec 2019 20:31:50 +0000 (21:31 +0100)]
mpc85xx: add support for Enterasys WS-AP3710i
Hardware
--------
SoC: NXP P1020 (2x e500 @ 800MHz)
RAM: 256M DDR3 (Micron)
FLASH: 32M NOR (Spansion S29GL128S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 1x Gigabit Ethernet (Atheros AR8033)
LED: System (green/red) - Radio{0,1} (green)
LAN (connected to PHY)
- GE blue
- FE green
Serial is a Cisco-compatible RJ45 next to the ethernet port.
115200-N-8 are the settings for OS and U-Boot.
Installation
------------
1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in
the root directory of a TFTP server and serve it at
192.168.200.200/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Set the bootcmd so the AP can boot OpenWrt by executing
Hans Dedecker [Wed, 11 Dec 2019 21:27:26 +0000 (22:27 +0100)]
glibc: update to latest 2.27 commit (BZ #2503, BZ #2504)
bef0b1cb31 libio: Disable vtable validation for pre-2.1 interposed handles [BZ #25203] 4d5cfeb510 rtld: Check __libc_enable_secure before honoring LD_PREFER_MAP_32BIT_EXEC (CVE-2019-19126) [BZ #25204] 92f04eedb5 mips: Force RWX stack for hard-float builds that can run on pre-4.8 kernels
Alin Nastac [Thu, 21 Nov 2019 13:06:18 +0000 (14:06 +0100)]
glibc: backport fix for regexec buffer read overrun
Problem found by AddressSanitizer[1]:
Latest `grep` (git commit 1019e6e) compiled with asan may cause a
heap-buffer-overflow when `-i` is specified.
./grep -i '\(\(\)*.\)*\(\)\(\)\1' /bin/chvt
=================================================================
==16206==ERROR: AddressSanitizer: heap-buffer-overflow on address
1. https://debbugs.gnu.org/34140
Ref: https://sourceware.org/bugzilla/show_bug.cgi?id=24114 Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
[commit title and description facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hans Dedecker [Tue, 17 Sep 2019 20:11:26 +0000 (22:11 +0200)]
glibc: update to latest 2.27 commit (BZ#23637)
5b4f7382af Add undef to fix test failure. 9456483fb2 Improve performance of memmem 373f8b06a3 Improve performance of strstr 4ec1b9e913 Fix strstr bug with huge needles (bug 23637) ecd6271ed8 Speedup first memmem match bba6b9288f Simplify and speedup strstr/strcasestr first match 7a4da6ef7a Improve strstr performance
5f0d2e0491 [AArch64] Add ifunc support for Ares e6b7252040 aarch64,falkor: Use vector registers for memcpy c74b884f70 aarch64,falkor: Ignore prefetcher tagging for smaller copies 0fc5934ebd aarch64/strncmp: Use lsr instead of mov+lsr e0a0bd3acc aarch64/strncmp: Unbreak builds with old binutils 638caf3000 aarch64: Improve strncmp for mutually misaligned inputs d5f45a29ff aarch64/strcmp: fix misaligned loop jump target 7f690fafad aarch64: Improve strcmp unaligned performance 40df047b3b aarch64: Fix branch target to loop16 062139f233 aarch64: Optimized memcmp for medium to large sizes f3e2add213 aarch64: Use the L() macro for labels in memcmp 22bd3ab40e posix: Fix large mmap64 offset for mips64n32 (BZ#24699) bdd16894aa aarch64: handle STO_AARCH64_VARIANT_PCS 0b48caab9a aarch64: add STO_AARCH64_VARIANT_PCS and DT_AARCH64_VARIANT_PCS 949da7f2fd io: Remove copy_file_range emulation [BZ #24744] f056ac8363 libio: do not attempt to free wide buffers of legacy streams [BZ #24228] 5f90e009b1 NEWS: add entries for bugs 22964, 24180, and 24531
ramips: allow JCG_MAXSIZE in kiB in Build/jcg-header
This allows JCG_MAXSIZE to be specified in kilobytes. This makes
this value more consistent and easier comparable with other size
variables.
This also changes the only occurence of the variable, for Cudy WR1000.
This is backported to 19.07 for convenience, as other developers
backporting device support might not be aware that JCG_MAXSIZE in
kilobytes would not work there.
Olli Asikainen [Fri, 15 Nov 2019 15:07:37 +0000 (17:07 +0200)]
brcm47xx: add switch configuration for WNR3500L
Netgear WNR3500L is an already supported device, but out of the
box, the device has no switch configuration and there is no wan.
The correct configuration for this specific model is similar to
some other models. This simple commit adds the correct switch
and the out-of-the-box experience is improved.
Experimentally determined:
Port 0 => WAN
Port 1..4 => LAN
Port 5..7 => unused
Port 8 => CPU
Signed-off-by: Olli Asikainen <olli.asikainen@gmail.com> Tested-by: Fabian Zaremba <fabian@youremail.eu>
[added port mapping to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit deb835849aeb713968aaa48bf046101140ab4825)
Martin Schiller [Wed, 4 Dec 2019 09:43:02 +0000 (10:43 +0100)]
ramips: fix number of LAN Ports for Mikrotik RBM33G
The Mikrotik RBM33G has only 2 LAN ports.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[moved node in 02_network to maintain alphabetic sorting; backport] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 3a55c7935d4efdc86575601cb4aa7bc94e3c5e44)
Walter Sonius [Wed, 4 Dec 2019 20:07:58 +0000 (21:07 +0100)]
ramips: fix switch port order for TP-Link Archer C20i
Physical port order watched from the backside of the C20i
(from left to right) is: Internet / 1 / 2 / 3 / 4
Physical Port Switch port
WAN 0
LAN 3 1
LAN 4 2
LAN 1 3
LAN 2 4
(not used) 5
CPU 6
Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[commit message/title improvements; backport to 19.07] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a065cd29bf2dfd1ce1f07becd65aef96cec658e7)
* November 29, 2019: Fix IBSS merge issue, related to TSF id leakage bug in firmware code.
Thanks for Ahmed Zaki @ Mage-Networks for helping to diagnose and test.
The release notes since last time for wave-2:
* December 6, 2019: Fix 160Mhz problem caused by logic that did not take into account the fact that
160Mhz has only 1/2 of the NSS of lower bandwidths in the rate table.
David Bauer [Sun, 24 Nov 2019 19:53:39 +0000 (20:53 +0100)]
generic ar8xxx: increase VLAN table for AR83x7
The Atheros AR8327 and AR8337 have (according to their datasheet) a
VLAN table with a maximum of 4096 entries.
Currently, there's a hard limit of 128 VLANs, which is the same as
for most other Atheros switches. Increase this limit only for the
AR83x7 series and modify some shared functions to allow them to work
with a variable max VLAN count.
Satadru Pramanik [Fri, 15 Nov 2019 17:42:44 +0000 (12:42 -0500)]
busybox: add glibc dependency for vi regex option
Build with musl libc fails with BUSYBOX_DEFAULT_FEATURE_VI_REGEX_SEARCH
enabled. Enabling BusyBox's vi regex search option depends upon GNU
regex. Musl libc does not support GNU regex[1].
So this patch adds explicit dependency on GNU libc and while at it
remove the FIXME comment.
Piotr Dymacz [Tue, 12 Nov 2019 21:36:28 +0000 (22:36 +0100)]
ath79: add support for YunCore XD4200 and A782
YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based
(QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE
(802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller
version of the XD4200, with similar specification but lower TX power.
Specification:
- QCA9563 (775 MHz)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN)
- Wi-Fi 2.4 GHz:
- XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA
- A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11)
- Wi-Fi 5 GHz:
- XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11)
- A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11)
- LEDs:
- XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet)
- A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet)
- 1x button (reset)
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x DC jack (12 V)
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Vincent Wiemann [Mon, 12 Aug 2019 23:26:45 +0000 (01:26 +0200)]
ath79: add support for YunCore TFTP image generation
YunCore QCA9k based devices released in 2019 require a custom TFTP image
for U-Boot built-in recovery mode (triggered with reset button). Image
has to be prepended with 'YUNCORE' keyword followed by U-Boot CLI
commands which will be executed later. Images without the custom header
will be ignored by U-Boot.
To be able to support both the vendor firmware (QSDK) and OpenWrt flash
layouts, used here commands change the 'bootcmd' before flashing image.
This commit adds generic helper script for YunCore devices with 16 MB of
flash and enables TFTP image generation for A770 model.
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[pepe2k@gmail.com: commit description reworded, recipe renamed] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit 8016f648640e8f73f0dc4fc307fb6bebd12afb88)
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Sungbo Eo [Mon, 11 Nov 2019 16:20:45 +0000 (01:20 +0900)]
base-files: config_generate: split macaddr with multiple ifaces
netifd does not handle network.@device[x].name properly if it
contains multiple ifaces separated by spaces. Due to this, board.d
lan_mac setup does not work if multiple ifaces are set to LAN by
ucidef_set_interface_lan.
To fix this, create a device node for each member iface when
running config_generate instead. Those are named based on the
member ifname:
config device 'lan_eth0_dev'
option name 'eth0'
option macaddr 'yy:yy:yy:yy:yy:01'
config device 'lan_eth1_1_dev'
option name 'eth1.1'
option macaddr 'yy:yy:yy:yy:yy:01'
ref: https://github.com/openwrt/openwrt/pull/2542
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[always use new scheme, extend description, change commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 298814e6be7640d89328de9e7c90d4349e30683f)
Lech Perczak [Sun, 17 Nov 2019 19:58:27 +0000 (20:58 +0100)]
ar71xx: ubnt-(xm,xw): add rssileds package
In order to make RSSI indicator on the device work out of box,
include "rssileds" package in per-device rootfs image by default
for Ubiquiti XM and XW devices, namely:
- Bullet M (XM/XW)
- Rocket M (XM/XW)
- Nanostation M (XM/XW)
- Nanostation Loco-M (XW)
This moves the package addition to the individual devices in order
to prevent accidental inclusions of the package when not looking
at the parent node carefully enough.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[add bullet-m-xw, remove rocket-m-ti, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 08d9c95417399ac8615df210f4381cca68a4b25c)
Piotr Dymacz [Sun, 3 Nov 2019 11:12:44 +0000 (12:12 +0100)]
ramips: add support for ALFA Network Quad-E4G
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.
Specification:
- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/1000 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)
Other:
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
has additional logic circuit for M.2 SIM switching. The 'sim-select'
will work only if both SIM slots are occupied. Otherwise, always slot
with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
slots but setting GPIO22 to high allows PERSTn control per slot, using
GPIO23-25 (value is inverted)
Flash instructions:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Piotr Dymacz [Tue, 29 Oct 2019 23:10:40 +0000 (00:10 +0100)]
ramips: add support for ALFA Network R36M-E4G
ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform
based on MediaTek MT7620A WiSoC. This product is designed for operation
with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06)
but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses).
Specification:
- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32+ MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 2x u.fl antenna connectors (for Wi-Fi)
- 8x LED (7 driven by GPIO)
- 2x button (reset, wifi)
- 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB
- 1x I2C (4-pin, 1.27 mm pitch) header on PCB
- 1x LED (8-pin, 1.27 mm pitch) header on PCB
- 1x DC jack with lock (12 V)
Other:
- there is a dedicated, 4-pin connector for optional RTC module (Holtek
HT138x) with 'enable' input, not available at the time of preparing
support for this board
- miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a
jumper resistor (R174) is not installed by default
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will
work only if both slots are occupied, otherwise U-Boot will always
select slot with SIM card inside (user can override it later, in
user-space)
- U-Boot resets the modem, using PERSTn signal, before starting kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
Flash instruction:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Piotr Dymacz [Tue, 29 Oct 2019 22:25:56 +0000 (23:25 +0100)]
ramips: support dual image feature on ALFA Network boards
New U-Boot version for MediaTek MT76x8/MT762x based ALFA Network boards
includes support for a 'dual image' feature. Users can enable it using
U-Boot environment variable 'dual_image' ('1' -> enabled).
When 'dual image' feature is enabled, U-Boot will modify DTB and divide
the original 'firmware' flash area into two, equal in size and aligned
to 64 KB partitions: 'firmware' and 'backup'. U-Boot will also adjust
size of 'firmware' area to match installed flash chip size.
U-Boot will load kernel from active partition which is marked with env
variable 'bootactive' ('1' -> first partition, '2' -> second partition)
and rename both partitions accordingly ('firmware' <-> 'backup').
There are 3 additional env variables used to control 'dual image' mode:
- bootlimit - maximum number of unsuccessful boot tries (default: '3')
- bootcount - current number of boot tries
- bootchanged - flag which informs that active partition was changed; if
it is set and 'bootcount' reaches 'bootlimit' value,
U-Boot will start web-based recovery which then updates
both partitions with provided image
Chuanhong Guo [Thu, 27 Jun 2019 12:44:27 +0000 (20:44 +0800)]
ramips: use upstream RAW_APPENDED_DTB instead of our OWRTDTB
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit: 02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")
Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8] Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620] Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(cherry picked from commit 7a8d3432c739c6ff038295176e8b6324e92fc116) Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Stijn Segers [Fri, 22 Nov 2019 18:39:19 +0000 (19:39 +0100)]
ath79: remove ath10k drivers from Archer C7 v1 profile
Ath10k packages were removed from ar71xx in master in commit 34113999ef43 ("ar71xx: Remove ath10k packages from archer-c7-v1 (fixes
FS#1743)") but ath79 in master and the 19.07 branch still suffer from
the issue.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[commit subject and description facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
It seems that there is a missing PKG_SOURCE_URL_FILE support.
This little fix adds the support for packages to change the name of the
downloaded file.
Sometimes it is desirable to change the downloaded archive file name, like
for mitigating name conflicts for different packages (some files on the server
could be named like, e.g. 2018-01-01.tar.gz) or for the cases that there is
no name for the file in the URL (e.g. http://someserver.com/download).
[ -n "$noscan" -a "$noscan" -gt 0 ] && hostapd_noscan=1
But if length of "$noscan" is zero (noscan is not set) this doesn't stop
the shell to evaluate the rest of the test.
root@hank2:~# [ -n "$noscan" -a "$noscan" -gt 0 ]
ash: out of range
root@hank2:~#
So when radios are brought up this shows in the log:
Sat Nov 23 10:51:38 2019 daemon.info procd: - init complete -
Sat Nov 23 10:52:24 2019 daemon.notice netifd: radio1 (1243): sh: out of range
Sat Nov 23 10:52:25 2019 user.notice firewall: Reloading firewall due to ifup of wan (eth0.2)
Sat Nov 23 10:52:25 2019 daemon.notice netifd: radio0 (1242): sh: out of range
Sat Nov 23 10:52:26 2019 authpriv.info dropbear[1536]: Not backgrounding
This commit sets noscan to 0 if unset and removes the gratuitous length
check, preventing the warning.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
(cherry picked from commit 28d84331f4bba5923059e701f5d4878b2df3fa79) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hauke Mehrtens [Fri, 22 Nov 2019 21:43:25 +0000 (22:43 +0100)]
e2fsprogs: Fix CVE-2019-5094 in libsupport
This adds the following patch from debian:
https://git.kernel.org/pub/scm/fs/ext2/e2fsprogs.git/commit/?h=debian/stable&id=09fe1fd2a1f9efc3091b4fc61f1876d0785956a8
libsupport: add checks to prevent buffer overrun bugs in quota code
projects / thirdparty / openwrt.git / log
