The pad argument to v4l2_subdev_state_xlate_streams() is incorrect, static
pad number is used for the source pad even though the pad number is
dependent on the stream. Fix it.
Add video_device_release() in label 'err_m2m' to release the memory
allocated by video_device_alloc() and prevent potential memory leaks.
Remove the reduntant code in label 'err_m2m'.
Fixes: a8ef0488cc59 ("media: imx: add csc/scaler mem2mem device") Cc: stable@vger.kernel.org Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com> Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The test pattern is set by a 8-bit register according to the
specification.
+--------+-------------------------------+
| BIT[0] | Solid color |
+--------+-------------------------------+
| BIT[1] | Color bar |
+--------+-------------------------------+
| BIT[2] | Fade to grey color bar |
+--------+-------------------------------+
| BIT[3] | PN9 |
+--------+-------------------------------+
| BIT[4] | Gradient horizontal |
+--------+-------------------------------+
| BIT[5] | Gradient vertical |
+--------+-------------------------------+
| BIT[6] | Check board |
+--------+-------------------------------+
| BIT[7] | Slant pattern |
+--------+-------------------------------+
Based on function above, current test pattern programming is wrong.
This patch fixes it by 'BIT(pattern - 1)'. If pattern is 0, driver
will disable the test pattern generation and set the pattern to 0.
Fixes: e62138403a84 ("media: hi556: Add support for Hi-556 sensor") Cc: stable@vger.kernel.org Signed-off-by: Bingbu Cao <bingbu.cao@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This sd_init() function reads the firmware. The firmware data holds a
series of records and the function reads each record and sends the data
to the device. The request_ihex_firmware() function
calls ihex_validate_fw() which ensures that the total length of all the
records won't read out of bounds of the fw->data[].
However, a potential issue is if there is a single very large
record (larger than PAGE_SIZE) and that would result in memory
corruption. Generally we trust the firmware, but it's always better to
double check.
Fixes: 49b61ec9b5af ("[media] gspca: Add new vicam subdriver") Cc: stable@vger.kernel.org Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
int main(int argc, char **argv)
{
unsigned long page_size = sysconf(_SC_PAGESIZE);
char *p = malloc(3 * page_size);
char *p_aligned;
/* initialize memory region. If not initialized, write syscall below will correctly return EFAULT. */
if (1)
memset(p, 'X', 3 * page_size);
p_aligned = (char *) ((((uintptr_t) p) + (2*page_size - 1)) & ~(page_size - 1));
/* Drop PROT_READ protection. Kernel and userspace should fault when accessing that memory region */
mprotect(p_aligned, page_size, PROT_NONE);
/* the following write() should return EFAULT, since PROT_READ was dropped by previous mprotect() */
int ret = write(2, p_aligned, 1);
if (!ret || errno != EFAULT)
printf("\n FAILURE: write() did not returned expected EFAULT value\n");
return 0;
}
Because of the way _PAGE_READ is handled, kernel code never generates
a read access fault when it access a page as the kernel privilege level
is always less than PL1 in the PTE.
This patch reworks the comments in the make_insert_tlb macro to try
to make this clearer.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org # v5.12+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use load and stbys,e instructions to trigger memory reference
interruptions without writing to memory. Because of the way read
access support is implemented, read access interruptions are only
triggered at privilege levels 2 and 3. The kernel and gateway
page execute at privilege level 0, so this code never triggers
a read access interruption. Thus, it is currently possible for
user code to execute a LWS compare and swap operation at an
address that is read protected at privilege level 3 (PRIV_USER).
Fix this by probing read access rights at privilege level 3 and
branching to lws_fault if access isn't allowed.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org # v5.12+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of the way read access support is implemented, read access
interruptions are only triggered at privilege levels 2 and 3. The
kernel executes at privilege level 0, so __get_user() never triggers
a read access interruption (code 26). Thus, it is currently possible
for user code to access a read protected address via a system call.
Fix this by probing read access rights at privilege level 3 (PRIV_USER)
and setting __gu_err to -EFAULT (-14) if access isn't allowed.
Note the cmpiclr instruction does a 32-bit compare because COND macro
doesn't work inside asm.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org # v5.12+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For building a 64-bit kernel, both 32-bit and 64-bit VDSO binaries
are built, so both 32-bit and 64-bit compilers (and tools) should be
in the PATH environment variable.
Because of the way the _PAGE_READ is handled in the parisc PTE, an
access interruption is not generated when the kernel reads from a
region where the _PAGE_READ is zero. The current code was written
assuming read access faults would also occur in the kernel.
This change adds user access checks to raw_copy_from_user(). The
prober_user() define checks whether user code has read access to
a virtual address. Note that page faults are not handled in the
exception support for the probe instruction. For this reason, we
precede the probe by a ldb access check.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org # v5.12+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 13a4b7fb6260 ("pmdomain: core: Leave powered-on genpds on
until late_initcall_sync") was applied, the Tegra210 Jetson TX1 board
failed to boot. Looking into this issue, before this commit was applied,
if any of the Tegra power-domains were in 'on' state when the kernel
booted, they were being turned off by the genpd core before any driver
had chance to request them. This was purely by luck and a consequence of
the power-domains being turned off earlier during boot. After this
commit was applied, any power-domains in the 'on' state are kept on for
longer during boot and therefore, may never transitioned to the off
state before they are requested/used. The hang on the Tegra210 Jetson
TX1 is caused because devices in some power-domains are accessed without
the power-domain being turned off and on, indicating that the
power-domain is not in a completely on state.
>From reviewing the Tegra PMC driver code, if a power-domain is in the
'on' state there is no guarantee that all the necessary clocks
associated with the power-domain are on and even if they are they would
not have been requested via the clock framework and so could be turned
off later. Some power-domains also have a 'clamping' register that needs
to be configured as well. In short, if a power-domain is already 'on' it
is difficult to know if it has been configured correctly. Given that the
power-domains happened to be switched off during boot previously, to
ensure that they are in a good known state on boot, fix this by
switching off any power-domains that are on initially when registering
the power-domains with the genpd framework.
Note that commit 05cfb988a4d0 ("soc/tegra: pmc: Initialise resets
associated with a power partition") updated the
tegra_powergate_of_get_resets() function to pass the 'off' to ensure
that the resets for the power-domain are in the correct state on boot.
However, now that we may power off a domain on boot, if it is on, it is
better to move this logic into the tegra_powergate_add() function so
that there is a single place where we are handling the initial state of
the power-domain.
The commit 65c66047259f ("proc: fix the issue of proc_mem_open returning
NULL") caused proc_maps_open() to return -ESRCH when proc_mem_open()
returns NULL. This breaks legitimate /proc/<pid>/maps access for kernel
threads since kernel threads have NULL mm_struct.
The regression causes perf to fail and exit when profiling a kernel
thread:
# perf record -v -g -p $(pgrep kswapd0)
...
couldn't open /proc/65/task/65/maps
This patch partially reverts the commit to fix it.
Link: https://lkml.kernel.org/r/20250807165455.73656-1-wjl.linux@gmail.com Fixes: 65c66047259f ("proc: fix the issue of proc_mem_open returning NULL") Signed-off-by: Jialin Wang <wjl.linux@gmail.com> Cc: Penglei Jiang <superman.xpt@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in commit 7a54947e727b ('Merge patch series "fs: allow
changing idmappings"'), open_tree_attr(2) was necessary in order to
allow for a detached mount to be created and have its idmappings changed
without the risk of any racing threads operating on it. For this reason,
mount_setattr(2) still does not allow for id-mappings to be changed.
However, there was a bug in commit 2462651ffa76 ("fs: allow changing
idmappings") which allowed users to bypass this restriction by calling
open_tree_attr(2) *without* OPEN_TREE_CLONE.
can_idmap_mount() prevented this bug from allowing an attached
mountpoint's id-mapping from being modified (thanks to an is_anon_ns()
check), but this still allows for detached (but visible) mounts to have
their be id-mapping changed. This risks the same UAF and locking issues
as described in the merge commit, and was likely unintentional.
This driver, for the time being, assumes that the kernel page size is 4kB,
so it fails on loong64 and aarch64 with 16kB pages, and ppc64el with 64kB
pages.
Signed-off-by: Simon Richter <Simon.Richter@hogyros.de> Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs") Cc: stable@vger.kernel.org # v6.8+ Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> Link: https://lore.kernel.org/r/20250802024152.3021-1-Simon.Richter@hogyros.de
(cherry picked from commit 0521a868222ffe636bf202b6e9d29292c1e19c62) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The userprogs infrastructure does not expect clang being used with GNU ld
and in that case uses /usr/bin/ld for linking, not the configured $(LD).
This fallback is problematic as it will break when cross-compiling.
Mixing clang and GNU ld is used for example when building for SPARC64,
as ld.lld is not sufficient; see Documentation/kbuild/llvm.rst.
Relax the check around --ld-path so it gets used for all linkers.
Fixes: dfc1b168a8c4 ("kbuild: userprogs: use correct lld when linking through clang") Cc: stable@vger.kernel.org Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de> Reviewed-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kunit test is using assignments to
"static volatile void *kasan_ptr_result" to prevent elision of memory
loads, but that's not working:
In this variable definition, the "volatile" applies to the "void", not to
the pointer.
To make "volatile" apply to the pointer as intended, it must follow
after the "*".
This makes the kasan_memchr test pass again on my system. The
kasan_strings test is still failing because all the definitions of
load_unaligned_zeropad() are lacking explicit instrumentation hooks and
ASAN does not instrument asm() memory operands.
Both jbd2_log_do_checkpoint() and jbd2_journal_shrink_checkpoint_list()
periodically release j_list_lock after processing a batch of buffers to
avoid long hold times on the j_list_lock. However, since both functions
contend for j_list_lock, the combined time spent waiting and processing
can be significant.
jbd2_journal_shrink_checkpoint_list() explicitly calls cond_resched() when
need_resched() is true to avoid softlockups during prolonged operations.
But jbd2_log_do_checkpoint() only exits its loop when need_resched() is
true, relying on potentially sleeping functions like __flush_batch() or
wait_on_buffer() to trigger rescheduling. If those functions do not sleep,
the kernel may hit a softlockup.
Commit d279c80e0bac ("iomap: inline iomap_dio_bio_opflags()") has broken
the logic in iomap_dio_bio_iter() in a way that when the device does
support FUA (or has no writeback cache) and the direct IO happens to
freshly allocated or unwritten extents, we will *not* issue fsync after
completing direct IO O_SYNC / O_DSYNC write because the
IOMAP_DIO_WRITE_THROUGH flag stays mistakenly set. Fix the problem by
clearing IOMAP_DIO_WRITE_THROUGH whenever we do not perform FUA write as
it was originally intended.
CC: John Garry <john.g.garry@oracle.com> CC: Ritesh Harjani (IBM) <ritesh.list@gmail.com> Fixes: d279c80e0bac ("iomap: inline iomap_dio_bio_opflags()") CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/20250730102840.20470-2-jack@suse.cz Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com> Reviewed-by: John Garry <john.g.garry@oracle.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the I2C frequency table to match the recommended values
specified in the I2C hardware programming guide. In the current IPQ5424
configuration where 32MHz is the source clock, the I2C bus frequencies do
not meet expectations—for instance, 363KHz is achieved instead of the
expected 400KHz.
Fixes: 506bb2ab0075 ("i2c: qcom-geni: Support systems with 32MHz serial engine clock") Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com> Cc: <stable@vger.kernel.org> # v6.13+ Reviewed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com> Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Link: https://lore.kernel.org/r/20250513-i2c-bus-freq-v1-1-9a333ad5757f@oss.qualcomm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The root cause is in the corrupted image, there is a dnode has the same
node id w/ its inode, so during f2fs_get_dnode_of_data(), it tries to
access block address in dnode at offset 934, however it parses the dnode
as inode node, so that get_dnode_addr() returns 360, then it tries to
access page address from 360 + 934 * 4 = 4096 w/ 4 bytes.
To fix this issue, let's add sanity check for node id of all direct nodes
during f2fs_get_dnode_of_data().
The commit 245618f8e45f ("block: protect wbt_lat_usec using
q->elevator_lock") protected wbt_enable_default() with
q->elevator_lock; however, it also placed wbt_enable_default()
before blk_queue_flag_set(QUEUE_FLAG_REGISTERED, q);, resulting
in wbt failing to be enabled.
Moreover, the protection of wbt_enable_default() by q->elevator_lock
was removed in commit 78c271344b6f ("block: move wbt_enable_default()
out of queue freezing from sched ->exit()"), so we can directly fix
this issue by placing wbt_enable_default() after
blk_queue_flag_set(QUEUE_FLAG_REGISTERED, q);.
Additionally, this issue also causes the inability to read the
wbt_lat_usec file, and the scenario is as follows:
Replace GFP_ATOMIC with GFP_KERNEL for dma_alloc_coherent() calls. This
change improves memory allocation reliability during firmware loading,
particularly during system resume when memory pressure is high. Because
of using GFP_KERNEL, reclaim can happen which can reduce the probability
of failure.
Fixes memory allocation failures observed during system resume with
fragmented memory conditions.
snd_sof_amd_vangogh 0000:04:00.5: error: failed to load DSP firmware after resume -12
Fixes: 145d7e5ae8f4e ("ASoC: SOF: amd: add option to use sram for data bin loading") Fixes: 7e51a9e38ab20 ("ASoC: SOF: amd: Add fw loader and renoir dsp ops to load firmware") Cc: stable@vger.kernel.org Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com> Link: https://patch.msgid.link/20250725190254.1081184-1-usama.anjum@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current configuration used for the IPQ5332 M31 USB PHY fails the
Near End High Speed Signal Quality compliance test. To resolve this,
update the initialization sequence as specified in the Hardware Design
Document.
vhost_vsock_alloc_skb() returns NULL for packets advertising a length
larger than VIRTIO_VSOCK_MAX_PKT_BUF_SIZE in the packet header. However,
this is only checked once the SKB has been allocated and, if the length
in the packet header is zero, the SKB may not be freed immediately.
Hoist the size check before the SKB allocation so that an iovec larger
than VIRTIO_VSOCK_MAX_PKT_BUF_SIZE + the header size is rejected
outright. The subsequent check on the length field in the header can
then simply check that the allocated SKB is indeed large enough to hold
the packet.
Cc: <stable@vger.kernel.org> Fixes: 71dc9ec9ac7d ("virtio/vsock: replace virtio_vsock_pkt with sk_buff") Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Will Deacon <will@kernel.org>
Message-Id: <20250717090116.11987-2-will@kernel.org> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving a vsock packet in the guest, only the virtqueue buffer
size is validated prior to virtio_vsock_skb_rx_put(). Unfortunately,
virtio_vsock_skb_rx_put() uses the length from the packet header as the
length argument to skb_put(), potentially resulting in SKB overflow if
the host has gone wonky.
Validate the length as advertised by the packet header before calling
virtio_vsock_skb_rx_put().
Cc: <stable@vger.kernel.org> Fixes: 71dc9ec9ac7d ("virtio/vsock: replace virtio_vsock_pkt with sk_buff") Signed-off-by: Will Deacon <will@kernel.org>
Message-Id: <20250717090116.11987-3-will@kernel.org> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Documentation/PCI/endpoint/pci-endpoint-cfs.rst, the Endpoint
controller (EPC) should only start the link when userspace writes '1' to
the '/sys/kernel/config/pci_ep/controllers/<EPC>/start' attribute, which
ultimately results in calling imx_pcie_start_link() via
pci_epc_start_store().
To align with the documented behavior, do not start the link automatically
when adding the EP controller.
Fixes: 75c2f26da03f ("PCI: imx6: Add i.MX PCIe EP mode support") Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded commit subject and description] Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250709033722.2924372-3-hongxing.zhu@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
apps_reset corresponds to LTSSM_EN in i.MX7, i.MX8MQ, i.MX8MM and i.MX8MP
platforms. Since assertion/de-assertion of apps_reset is done in
imx_pcie_ltssm_enable() and imx_pcie_ltssm_disable(), remove it from
imx_pcie_assert_core_reset() and imx_pcie_deassert_core_reset().
This also fixes a failure in enumerating the PI7C9X2G608GP (hotplug) chip
reliably on i.MX8MM, as reported by Tim.
It should be noted that only i.MX7D, i.MX8MQ, i.MX8MM, and i.MX8MP
platforms have the apps_reset logic, so this change doesn't have any effect
on other platforms.
Fixes: ef61c7d8d032 ("PCI: imx6: Deassert apps_reset in imx_pcie_deassert_core_reset()") Reported-by: Tim Harvey <tharvey@gateworks.com> Closes: https://lore.kernel.org/all/CAJ+vNU3ohR2YKTwC4xoYrc1z-neDoH2TTZcMHDy+poj9=jSy+w@mail.gmail.com/ Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded commit subject and description] Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Tim Harvey <tharvey@gateworks.com> # imx8mp-venice-gw74xx (i.MX8MP + hotplug capable switch) Reviewed-by: Frank Li <Frank.Li@nxp.com> Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250709033722.2924372-2-hongxing.zhu@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IMX8MQ_EP has three 64-bit BAR0/2/4 capable and programmable BARs. For
IMX8MQ_EP, use imx8q_pcie_epc_features (64-bit BARs 0, 2, 4) instead
of imx8m_pcie_epc_features (64-bit BARs 0, 2).
Fixes: 75c2f26da03f ("PCI: imx6: Add i.MX PCIe EP mode support") Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[bhelgaas: add details in subject] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250708091003.2582846-2-hongxing.zhu@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An endpoint driver configfs attributes group is added to the
epf_group list of struct pci_epf_driver by pci_epf_add_cfs() but an
added group is not removed from this list when the attribute group is
unregistered with pci_ep_cfs_remove_epf_group().
Add the missing list_del() call in pci_ep_cfs_remove_epf_group()
to correctly remove the attribute group from the driver list.
With this change, once the loop over all attribute groups in
pci_epf_remove_cfs() completes, the driver epf_group list should be
empty. Add a WARN_ON() to make sure of that.
Fixes: ef1433f717a2 ("PCI: endpoint: Create configfs entry for each pci_epf_device_id table entry") Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Reviewed-by: Niklas Cassel <cassel@kernel.org> Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250624114544.342159-3-dlemoal@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doing a list_del() on the epf_group field of struct pci_epf_driver in
pci_epf_remove_cfs() is not correct as this field is a list head, not
a list entry. This list_del() call triggers a KASAN warning when an
endpoint function driver which has a configfs attribute group is torn
down:
==================================================================
BUG: KASAN: slab-use-after-free in pci_epf_remove_cfs+0x17c/0x198
Write of size 8 at addr ffff00010f4a0d80 by task rmmod/319
When pcie_failed_link_retrain() fails to retrain, it tries to revert to the
previous link speed. However it calculates that speed from the Link
Control 2 register without masking out non-speed bits first.
PCIE_LNKCTL2_TLS2SPEED() converts such incorrect values to
PCI_SPEED_UNKNOWN (0xff), which in turn causes a WARN splat in
pcie_set_target_speed():
pci 0000:00:01.1: [1022:14ed] type 01 class 0x060400 PCIe Root Port
pci 0000:00:01.1: broken device, retraining non-functional downstream link at 2.5GT/s
pci 0000:00:01.1: retraining failed
WARNING: CPU: 1 PID: 1 at drivers/pci/pcie/bwctrl.c:168 pcie_set_target_speed
RDX: 0000000000000001 RSI: 00000000000000ff RDI: ffff9acd82efa000
pcie_failed_link_retrain
pci_device_add
pci_scan_single_device
Mask out the non-speed bits in PCIE_LNKCTL2_TLS2SPEED() and
PCIE_LNKCAP_SLS2SPEED() so they don't incorrectly return PCI_SPEED_UNKNOWN.
Fixes: de9a6c8d5dbf ("PCI/bwctrl: Add pcie_set_target_speed() to set PCIe Link Speed") Reported-by: Andrew <andreasx0@protonmail.com> Closes: https://lore.kernel.org/r/7iNzXbCGpf8yUMJZBQjLdbjPcXrEJqBxy5-bHfppz0ek-h4_-G93b1KUrm106r2VNF2FV_sSq0nENv4RsRIUGnlYZMlQr2ZD2NyB5sdj5aU=@protonmail.com/ Suggested-by: Maciej W. Rozycki <macro@orcam.me.uk> Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Jiwei Sun <sunjw10@lenovo.com>
[bhelgaas: commit log, add details from https://lore.kernel.org/r/1c92ef6bcb314ee6977839b46b393282e4f52e74.1750684771.git.lukas@wunner.de] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Cc: stable@vger.kernel.org # v6.13+ Link: https://patch.msgid.link/20250123055155.22648-2-sjiwei@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCIe port driver erroneously creates a subdevice for hotplug on ACPI
slots which are handled by the ACPI hotplug driver.
Avoid by checking the is_pciehp flag instead of is_hotplug_bridge when
deciding whether to create a subdevice. The latter encompasses ACPI slots
whereas the former doesn't.
The superfluous subdevice has no real negative impact, it occupies memory
and interrupt resources but otherwise just sits there waiting for
interrupts from the slot that are never signaled.
max_scan in page_cache_next_miss always decreases to zero when no hole is
found, causing the return value to be index + 0.
Fix this by preserving the max_scan value throughout the loop.
Jan said "From what I know and have seen in the past, wrong responses
from page_cache_next_miss() can lead to readahead window reduction and
thus reduced read speeds."
Link: https://lkml.kernel.org/r/20250605054935.2323451-1-chizhiling@163.com Fixes: 901a269ff3d5 ("filemap: fix page_cache_next_miss() when no hole found") Signed-off-by: Chi Zhiling <chizhiling@kylinos.cn> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Josef Bacik <josef@toxicpanda.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use "mtk-pmic-keys" when creating sub-device for the keypad to
make sure the keypad driver will only bind to the sub-device if it has
support for the variant/has matching compatible.
Cc: stable@vger.kernel.org Fixes: 6e31bb8d3a63 ("mfd: mt6397: Add initial support for MT6328") Fixes: de58cee8c6b8 ("mfd: mt6397-core: Add MT6357 PMIC support") Fixes: 4a901e305011 ("mfd: mt6397-core: Add resources for PMIC keys for MT6359") Reported-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Tested-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com> # on Link: https://lore.kernel.org/r/r4k3pgd3ew3ypne7ernxuzwgniiyvzosbce4cfajbcu7equblt@yato35tjb3lw Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 3d1f08b032dc ("mtd: spinand: Use the external ECC engine
logic") the spinand_write_page() function ignores the errors returned
by spinand_wait(). Change the code to propagate those up to the stack
as it was done before the offending change.
Commit ff67592cbdfc ("mtd: spi-nor: Introduce spi_nor_set_mtd_info()")
moved all initialization of the mtd fields at the end of spi_nor_scan().
Normally, the mtd info is only needed for the mtd ops on the device,
with one exception: spi_nor_try_unlock_all(), which will also make use
of the mtd->size parameter. With that commit, the size will always be
zero because it is not initialized. Fix that by not using the size of
the mtd_info struct, but use the size from struct spi_nor_flash_parameter.
The Linux hwmon sysfs API values for pwmX_auto_pointY_pwm represent an
integer value between 0 (0%) to 255 (100%) and the pwmX_auto_pointY_temp
represent millidegrees Celcius.
Commit a6d80df47ee2 ("hwmon: (gsc-hwmon) fix fan pwm temperature
scaling") properly addressed the incorrect scaling in the
pwm_auto_point_temp_store implementation but erroneously scaled
the pwm_auto_point_pwm_show (pwm value) instead of the
pwm_auto_point_temp_show (temp value) resulting in:
# cat /sys/class/hwmon/hwmon0/pwm1_auto_point6_pwm
25500
# cat /sys/class/hwmon/hwmon0/pwm1_auto_point6_temp
4500
Fix the scaling of these attributes:
# cat /sys/class/hwmon/hwmon0/pwm1_auto_point6_pwm
255
# cat /sys/class/hwmon/hwmon0/pwm1_auto_point6_temp
45000
Fixes: a6d80df47ee2 ("hwmon: (gsc-hwmon) fix fan pwm temperature scaling") Cc: stable@vger.kernel.org Signed-off-by: Tim Harvey <tharvey@gateworks.com> Link: https://lore.kernel.org/r/20250718200259.1840792-1-tharvey@gateworks.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
according to my tests with a signal analyser and also the documentation.
The current algorithm doesn't consider the `+ 1` part and so configures
slightly too high periods. The same issue exists for the duty cycle
setting. So subtract 1 from both the register values for period and
duty cycle. If period is 0, bail out, if duty_cycle is 0, just disable
the PWM which results in a constant low output.
Stop handling the clocks in pwm_mediatek_enable() and
pwm_mediatek_disable(). This is a preparing change for the next commit
that requires that clocks and the enable bit are handled separately.
Also move these two functions a bit further up in the source file to
make them usable in pwm_mediatek_config(), which is needed in the next
commit, too.
As per the i.MX93 TRM, section 67.3.2.1 "MOD register update", the value
of the TPM counter does NOT get updated when writing MOD.MOD unless
SC.CMOD != 0. Therefore, with the current code, assuming the following
sequence:
1) pwm_disable()
2) pwm_apply_might_sleep() /* period is changed here */
3) pwm_enable()
and assuming only one channel is active, if CNT.COUNT is higher than the
MOD.MOD value written during the pwm_apply_might_sleep() call then, when
re-enabling the PWM during pwm_enable(), the counter will end up resetting
after UINT32_MAX - CNT.COUNT + MOD.MOD cycles instead of MOD.MOD cycles as
normally expected.
Fix this problem by forcing a reset of the TPM counter before MOD.MOD is
written.
Add the missing memory barriers to make sure that destination ring
descriptors are read before updating the tail pointer (and passing
ownership to the device) to avoid memory corruption on weakly ordered
architectures like aarch64 when the ring is full.
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath11k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath11k_hal_srng_access_end().
Add the missing memory barriers to make sure that destination ring
descriptors are read before updating the tail pointer (and passing
ownership to the device) to avoid memory corruption on weakly ordered
architectures like aarch64 when the ring is full.
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath12k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath12k_hal_srng_access_end().
A new warning in clang [1] complains that diq_start in
wlc_lcnphy_tx_iqlo_cal() is passed uninitialized as a const pointer to
wlc_lcnphy_common_read_table():
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:2728:13: error: variable 'diq_start' is uninitialized when passed as a const pointer argument here [-Werror,-Wuninitialized-const-pointer]
2728 | &diq_start, 1, 16, 69);
| ^~~~~~~~~
The table pointer passed to wlc_lcnphy_common_read_table() should not be
considered constant, as wlc_phy_read_table() is ultimately going to
update it. Remove the const qualifier from the tbl_ptr to clear up the
warning.
Fix the setting of the ODR register value in the probe function for
AD7177. The AD7177 chip has a different ODR value after reset than the
other chips (0x7 vs. 0x0) and 0 is a reserved value on that chip.
The driver already has this information available in odr_start_value
and uses it when checking valid values when writing to the
sampling_frequency attribute, but failed to set the correct initial
value in the probe function.
Fix the channel index values passed to ad_sd_calibrate() in
ad7173_calibrate_all().
ad7173_calibrate_all() expects these values to be that of the CHANNELx
register assigned to the channel, not the datasheet INPUTx number of the
channel. The incorrect values were causing register writes to fail for
some channels because they set the WEN bit that must always be 0 for
register access and set the R/W bit to read instead of write. For other
channels, the channel number was just wrong because the CHANNELx
registers are generally assigned in reverse order and so almost never
match the INPUTx numbers.
Fixes: 031bdc8aee01 ("iio: adc: ad7173: add calibration support") Signed-off-by: David Lechner <dlechner@baylibre.com> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Link: https://patch.msgid.link/20250708-iio-adc-ad7313-fix-calibration-channel-v1-1-e6174e2c7cbf@baylibre.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the index used to look up the channel when accessing the
syscalib_mode attribute. The address field is a 0-based index (same
as scan_index) that it used to access the channel in the
ad7173_channels array throughout the driver. The channels field, on
the other hand, may not match the address field depending on the
channel configuration specified in the device tree and could result
in an out-of-bounds access.
Change the buffer disable callback from postdisable to predisable.
This balances the existing posteanble callback. Using postdisable
with posteanble can be problematic, for example, if update_scan_mode
fails, it would call postdisable without ever having called posteanble,
so the drivers using this would be in an unexpected state when
postdisable was called.
Fixes: af3008485ea0 ("iio:adc: Add common code for ADI Sigma Delta devices") Signed-off-by: David Lechner <dlechner@baylibre.com> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Link: https://patch.msgid.link/20250703-iio-adc-ad_sigma_delta-buffer-predisable-v1-1-f2ab85138f1f@baylibre.com Cc: <stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a potential out-of-bounds array access of the hw_xlate array in
bno055.c.
In bno055_get_regmask(), hw_xlate was iterated over the length of the
vals array instead of the length of the hw_xlate array. In the case of
bno055_gyr_scale, the vals array is larger than the hw_xlate array,
so this could result in an out-of-bounds access. In practice, this
shouldn't happen though because a match should always be found which
breaks out of the for loop before it iterates beyond the end of the
hw_xlate array.
By adding a new hw_xlate_len field to the bno055_sysfs_attr, we can be
sure we are iterating over the correct length.
Use common wrappers operating directly on the struct sg_table objects to
fix incorrect use of statterlists related calls. dma_unmap_sg() function
has to be called with the number of elements originally passed to the
dma_map_sg() function, not the one returned in sgtable's nents.
CC: stable@vger.kernel.org Fixes: 425902f5c8e3 ("fpga zynq: Use the scatterlist interface") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Xu Yilun <yilun.xu@intel.com> Link: https://lore.kernel.org/r/20250616120932.1090614-1-m.szyprowski@samsung.com Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the MDT loader is used in remoteproc, the ELF header is sanitized
beforehand, but that's not necessary the case for other clients.
Validate the size of the firmware buffer to ensure that we don't read
past the end as we iterate over the header. e_phentsize and e_shentsize
are validated as well, to ensure that the assumptions about step size in
the traversal are valid.
Delete extra checks for the ATA_DFLAG_CDL_ENABLED flag that prevent
SET FEATURES command from being issued to a drive when NCQ commands
are active.
ata_mselect_control_ata_feature() sets / clears the ATA_DFLAG_CDL_ENABLED
flag during the translation of MODE SELECT to SET FEATURES. If SET FEATURES
gets deferred due to outstanding NCQ commands, the original MODE SELECT
command will be re-queued. When the re-queued MODE SELECT goes through
the ata_mselect_control_ata_feature() translation again, SET FEATURES
will not be issued because ATA_DFLAG_CDL_ENABLED has been already set or
cleared by the initial translation of MODE SELECT.
The ATA_DFLAG_CDL_ENABLED checks in ata_mselect_control_ata_feature()
are safe to remove because scsi_cdl_enable() implements a similar logic
that avoids enabling CDL if it has been enabled already.
Fixes: 17e897a45675 ("ata: libata-scsi: Improve CDL control") Cc: stable@vger.kernel.org Signed-off-by: Igor Pylypiv <ipylypiv@google.com> Reviewed-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel MTL-like host controllers support auto-hibernate. Using
auto-hibernate with manual (driver initiated) hibernate produces more
complex operation. For example, the host controller will have to exit
auto-hibernate simply to allow the driver to enter hibernate state
manually. That is not recommended.
The default rpm_lvl and spm_lvl is 3, which includes manual hibernate.
Change the default values to 2, which does not.
Note, to be simpler to backport to stable kernels, utilize the UFS PCI
driver's ->late_init() call back. Recent commits have made it possible
to set up a controller-specific default in the regular ->init() call
back, but not all stable kernels have those changes.
Fixes: 4049f7acef3e ("scsi: ufs: ufs-pci: Add support for Intel MTL") Cc: stable@vger.kernel.org Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20250723165856.145750-3-adrian.hunter@intel.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UFSHCD core disables the UIC completion interrupt when issuing UIC
hibernation commands, and re-enables it afterwards if it was enabled to
start with, refer ufshcd_uic_pwr_ctrl(). For Intel MTL-like host
controllers, accessing the register to re-enable the interrupt disrupts
the state transition.
Use hibern8_notify variant operation to disable the interrupt during the
entire hibernation, thereby preventing the disruption.
Fixes: 4049f7acef3e ("scsi: ufs: ufs-pci: Add support for Intel MTL") Cc: stable@vger.kernel.org Signed-off-by: Archana Patni <archana.patni@intel.com> Link: https://lore.kernel.org/r/20250723165856.145750-2-adrian.hunter@intel.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ata_gen_ata_sense() is always called for a failed qc missing sense data
so that a sense key, code and code qualifier can be generated using
ata_to_sense_error() from the qc status and error fields of its result
task file. However, if the qc does not have its result task file filled,
ata_gen_ata_sense() returns early without setting a sense key.
Improve this by defaulting to returning ABORTED COMMAND without any
additional sense code, since we do not know the reason for the failure.
The same fix is also applied in ata_gen_passthru_sense() with the
additional check that the qc failed (qc->err_mask is set).
Fixes: 816be86c7993 ("ata: libata-scsi: Check ATA_QCFLAG_RTF_FILLED before using result_tf") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8ae720449fca ("libata: whitespace fixes in ata_to_sense_error()")
inadvertantly added the entry 0x40 (ATA_DRDY) to the stat_table array in
the function ata_to_sense_error(). This entry ties a failed qc which has
a status filed equal to ATA_DRDY to the sense key ILLEGAL REQUEST with
the additional sense code UNALIGNED WRITE COMMAND. This entry will be
used to generate a failed qc sense key and sense code when the qc is
missing sense data and there is no match for the qc error field in the
sense_table array of ata_to_sense_error().
As a result, for a failed qc for which we failed to get sense data (e.g.
read log 10h failed if qc is an NCQ command, or REQUEST SENSE EXT
command failed for the non-ncq case, the user very often end up seeing
the completely misleading "unaligned write command" error, even if qc
was not a write command. E.g.:
Fix this by removing the ATA_DRDY entry from the stat_table array so
that we default to always returning ABORTED COMMAND without any
additional sense code, since we do not know any better. The entry 0x08
(ATA_DRQ) is also removed since signaling ABORTED COMMAND with a parity
error is also misleading (as a parity error would likely be signaled
through a bus error). So for this case, also default to returning
ABORTED COMMAND without any additional sense code. With this, the
previous example error case becomes:
sd 0:0:0:0: [sda] tag#17 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
sd 0:0:0:0: [sda] tag#17 Sense Key : Aborted Command [current]
sd 0:0:0:0: [sda] tag#17 Add. Sense: No additional sense information
sd 0:0:0:0: [sda] tag#17 CDB: Read(10) 28 00 00 00 10 00 00 00 08 00
I/O error, dev sda, sector 4096 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
Together with these fixes, refactor stat_table to make it more readable
by putting the entries comments in front of the entries and using the
defined status bits macros instead of hardcoded values.
Reported-by: Lorenz Brun <lorenz@brun.one> Reported-by: Brandon Schwartz <Brandon.Schwartz@wdc.com> Fixes: 8ae720449fca ("libata: whitespace fixes in ata_to_sense_error()") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "is_waiting" flag was updated after calling complete(), which could
lead to a race where the waiting thread wakes up before the flag is
cleared. This may cause a missed wakeup or stale state check.
Reorder the operations to update "is_waiting" before signaling completion
to ensure consistent state.
On Google gs101, the number of UTP transfer request slots (nutrs) is 32,
and in this case the driver ends up programming the UTRL_NEXUS_TYPE
incorrectly as 0.
This is because the left hand side of the shift is 1, which is of type
int, i.e. 31 bits wide. Shifting by more than that width results in
undefined behaviour.
Fix this by switching to the BIT() macro, which applies correct type
casting as required. This ensures the correct value is written to
UTRL_NEXUS_TYPE (0xffffffff on gs101), and it also fixes a UBSAN shift
warning:
UBSAN: shift-out-of-bounds in drivers/ufs/host/ufs-exynos.c:1113:21
shift exponent 32 is too large for 32-bit type 'int'
For consistency, apply the same change to the nutmrs / UTMRL_NEXUS_TYPE
write.
Fixes: 55f4b1f73631 ("scsi: ufs: ufs-exynos: Add UFS host support for Exynos SoCs") Cc: stable@vger.kernel.org Signed-off-by: André Draszik <andre.draszik@linaro.org> Link: https://lore.kernel.org/r/20250707-ufs-exynos-shift-v1-1-1418e161ae40@linaro.org Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the 'mediatek,ufs-disable-mcq' property to the UFS device-tree
bindings. This flag corresponds to the UFS_MTK_CAP_DISABLE_MCQ host
capability recently introduced in the UFS host driver, allowing it to
disable the Multiple Circular Queue (MCQ) feature when present. The
binding schema has also been updated to resolve DTBS check errors.
Cc: stable@vger.kernel.org Fixes: 46bd3e31d74b ("scsi: ufs: mediatek: Add UFS_MTK_CAP_DISABLE_MCQ") Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> Link: https://lore.kernel.org/r/20250722085721.2062657-2-macpaul.lin@mediatek.com Reviewed-by: Rob Herring (Arm) <robh@kernel.org> Reviewed-by: Peter Wang <peter.wang@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with the RK3588 SoC, RK3576 also allows the use of HDMI PHY PLL as an
alternative and more accurate pixel clock source for VOP2.
Document the optional PLL clock property.
Moreover, given that this is part of a series intended to address some
recent display problems, provide the appropriate tags to facilitate
backporting.
'minItems' alone does not impose upper bound, unlike 'maxItems' which
implies lower bound. Add missing clock constraint so the list will have
exact number of items (clocks).
'minItems' alone does not impose upper bound, unlike 'maxItems' which
implies lower bound. Add missing clock constraint so the list will have
exact number of items (clocks).
The dfa blob stream for the aa_dfa_unpack() function is expected to be aligned
on a 8 byte boundary.
The static nulldfa_src[] and stacksplitdfa_src[] arrays store the initial
apparmor dfa blob streams, but since they are declared as an array-of-chars
the compiler and linker will only ensure a "char" (1-byte) alignment.
Add an __aligned(8) annotation to the arrays to tell the linker to always
align them on a 8-byte boundary. This avoids runtime warnings at startup on
alignment-sensitive platforms like parisc such as:
Kernel: unaligned access to 0x7f2a584a in aa_dfa_unpack+0x124/0x788 (iir 0xca0109f)
Kernel: unaligned access to 0x7f2a584e in aa_dfa_unpack+0x210/0x788 (iir 0xca8109c)
Kernel: unaligned access to 0x7f2a586a in aa_dfa_unpack+0x278/0x788 (iir 0xcb01090)
Signed-off-by: Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org Fixes: 98b824ff8984 ("apparmor: refcount the pdb") Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RK3588 GPU power domain cannot be activated unless the external
power regulator is already on. When GPU support was added to this DT,
we had no way to represent this requirement, so `regulator-always-on`
was added to the `vdd_gpu_s0` regulator in order to ensure stability.
A later patch series (see "Fixes:" commit) resolved this shortcoming,
but that commit left the workaround -- and rendered the comment above
it no longer correct.
Remove the workaround to allow the GPU power regulator to power off, now
that the DT includes the necessary information to power it back on
correctly.
Fixes: f94500eb7328b ("arm64: dts: rockchip: Add GPU power domain regulator dependency for RK3588") Signed-off-by: Sam Edwards <CFSworks@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250608184855.130206-1-CFSworks@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable internal bias pull-ups on the SoC-side I2C buses that do not have
external pull resistors populated on the SoM. This ensures proper
default line levels.
The device is available in multiple variants with differing RAM
capacities. The memory range defined in the 0x80000000 bank exceeds the
address range of the memory controller, which eventually leads to ARM
SError crashes. Reduce the bank size to a value which is available to
all devices.
The bootloader must be responsible for identifying the RAM capacity and
editing the memory node accordingly.
Fixes: d6f3a7f91fdb ("arm64: dts: exynos: add initial devicetree support for exynos7870") Cc: stable@vger.kernel.org # v6.16 Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org> Link: https://lore.kernel.org/r/20250626-exynos7870-dts-fixes-v1-2-349987874d9a@disroot.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves pinmux child nodes for sdhci0 node from k3-am62x-sk-common
to each top level board file. This is needed since we require internal
pullups for AM62x SK and not for AM62 LP SK since it has external
pullups on DATA 1-7.
Internal pulls are required for AM62 SK as per JESD84 spec
recommendation to prevent unconnected lines floating.
main_uart1 reserved for TIFS firmware traces is routed to the
onboard FT4232 via a FET switch which is connected to pin A21 and
B21 of the SoC and not E17 and C17. Fix it.
ufs-exynos driver configures the sysreg shareability as
cacheable for gs101 so we need to set the dma-coherent
property so the descriptors are also allocated cacheable.
This fixes the UFS stability issues we have seen with
the upstream UFS driver on gs101.
Fixes: 4c65d7054b4c ("arm64: dts: exynos: gs101: Add ufs and ufs-phy dt nodes") Cc: stable@vger.kernel.org Suggested-by: Will McVicker <willmcvicker@google.com> Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Tested-by: Will McVicker <willmcvicker@google.com> Tested-by: André Draszik <andre.draszik@linaro.org> Reviewed-by: André Draszik <andre.draszik@linaro.org> Link: https://lore.kernel.org/r/20250314-ufs-dma-coherent-v1-1-bdf9f9be2919@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with the RK3588 SoC, the HDMI PHY PLL on RK3576 can be used as a more
accurate pixel clock source for VOP2, which is actually mandatory to
ensure proper support for display modes handling.
Add the missing #clock-cells property to allow using the clock provider
functionality of HDMI PHY.
Since commit c871a311edf0 ("phy: rockchip: samsung-hdptx: Setup TMDS
char rate via phy_configure_opts_hdmi"), the workaround of passing the
rate from DW HDMI QP bridge driver via phy_set_bus_width() became
partially broken, as it cannot reliably handle mode switches anymore.
Attempting to fix this up at PHY level would not only introduce
additional hacks, but it would also fail to adequately resolve the
display issues that are a consequence of the system CRU limitations.
Instead, proceed with the solution already implemented for RK3588: make
use of the HDMI PHY PLL as a better suited DCLK source for VOP2. This
will not only address the aforementioned problem, but it should also
facilitate the proper operation of display modes up to 4K@60Hz.
It's worth noting that anything above 4K@30Hz still requires high TMDS
clock ratio and scrambling support, which hasn't been mainlined yet.
In gadget mode, USB connections are sluggish. The device won't send
packets to the host unless the host sends packets to the device. For
instance, SSH-ing through the USB network would apparently not work
unless you're flood-pinging the device's IP.
Add the property snps,usb2-gadget-lpm-disable to the dwc3 node, which
seems to solve this issue.
Fixes: d6f3a7f91fdb ("arm64: dts: exynos: add initial devicetree support for exynos7870") Cc: stable@vger.kernel.org # v6.16 Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org> Link: https://lore.kernel.org/r/20250626-exynos7870-dts-fixes-v1-1-349987874d9a@disroot.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch Schmitt Trigger functions for PIN_INPUT* macros by default. This is
HW PoR configuration, the slew rate requirements without ST enabled are
pretty tough for these devices. We've noticed spurious GPIO interrupts even
with noise-free edges but not meeting slew rate requirements (3.3E+6 V/s
for 3.3v LVCMOS).
It's not obvious why one might want to disable the PoR-enabled ST on any
pin. Just enable it by default. As it's not possible to provide OR-able
macros to disable the ST, shall anyone require it, provide a set of
new macros with _NOST suffix.
Fixes: fe49f2d776f7 ("arm64: dts: ti: Use local header for pinctrl register values") Cc: stable@vger.kernel.org Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com> Link: https://lore.kernel.org/r/20250701105437.3539924-1-alexander.sverdlin@siemens.com
[vigneshr@ti.com: Add Fixes tag] Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device is available in multiple variants with differing RAM
capacities. The memory range defined in the 0x80000000 bank exceeds the
address range of the memory controller, which eventually leads to ARM
SError crashes. Reduce the bank size to a value which is available to
all devices.
The bootloader must be responsible for identifying the RAM capacity and
editing the memory node accordingly.
Fixes: d6f3a7f91fdb ("arm64: dts: exynos: add initial devicetree support for exynos7870") Cc: stable@vger.kernel.org # v6.16 Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org> Link: https://lore.kernel.org/r/20250626-exynos7870-dts-fixes-v1-3-349987874d9a@disroot.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NODATASUM message was printed twice by mistake and the NODATACOW was
missing from the 'unset' part. Fix the duplication and make the output
look the same.
After the fsconfig migration in 6.8, mount option info messages are no
longer displayed during mount operations because btrfs_emit_options() is
only called during remount, not during initial mount.
Fix this by calling btrfs_emit_options() in btrfs_fill_super() after
open_ctree() succeeds. Additionally, prevent log duplication by ensuring
btrfs_check_options() handles validation with warn-level and err-level
messages, while btrfs_emit_options() provides info-level messages.
Fix a wrong log message that appears when the "nobarrier" mount option
is unset. When "nobarrier" is unset, barrier is actually enabled.
However, the log incorrectly stated "turning off barriers".
Since commit 13bb483d32ab ("btrfs: zoned: activate metadata block group on
write time"), we activate a metadata block group at the write time. If the
zone capacity is small enough, we can allocate the entire region before the
first write. Then, we hit the btrfs_zoned_bg_is_full() in
btrfs_zone_activate() and the activation fails.
For a data block group, we activate it at the allocation time and we should
check the fullness condition in the caller side. Add, a WARN to check the
fullness condition.
For a metadata block group, we don't need the fullness check because we
activate it at the write time. Instead, activating it once it is written
should be invalid. Catch that with a WARN too.
Fixes: 13bb483d32ab ("btrfs: zoned: activate metadata block group on write time") CC: stable@vger.kernel.org # 6.6+ Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a filesystem with a block size larger than 4KB, the hole length
calculation for a non-extent inode in ext4_ind_map_blocks() can easily
exceed INT_MAX. Then it could return a zero length hole and trigger the
following waring and infinite in the iomap infrastructure.
When the file system is frozen in preparation for taking an LVM
snapshot, the journal is checkpointed and if the orphan_file feature
is enabled, and the orphan file is empty, we clear the orphan_present
feature flag. But if there are pending inodes that need to be removed
the orphan_present feature flag can't be cleared.
The problem comes if the block device is read-only. In that case, we
can't process the orphan inode list, so it is skipped in
ext4_orphan_cleanup(). But then in ext4_mark_recovery_complete(),
this results in the ext4 error "Orphan file not empty on read-only fs"
firing and the file system mount is aborted.
Fix this by clearing the needs_recovery flag in the block device is
read-only. We do this after the call to ext4_load_and_init-journal()
since there are some error checks need to be done in case the journal
needs to be replayed and the block device is read-only, or if the
block device containing the externa journal is read-only, etc.
In some cases like small FSes with no meta_bg and where the resize
doesn't need extra gdt blocks as it can fit in the current one,
s_reserved_gdt_blocks is set as 0, which causes fsmap to emit a 0
length entry, which is incorrect.
With bigalloc enabled, the logic to report last extent has a bug since
we try to use cluster units instead of block units. This can cause an
issue where extra incorrect entries might be returned back to the
user. This was flagged by generic/365 with 64k bs and -O bigalloc.
** Details of issue **
The issue was noticed on 5G 64k blocksize FS with -O bigalloc which has
only 1 bg.
Only the first entry was expected to be returned but we get 2. This is
because:
ext4_getfsmap_datadev()
first_cluster, last_cluster = 0
...
info->gfi_last = true;
ext4_getfsmap_datadev_helper(sb, end_ag, last_cluster + 1, 0, info);
fsb = C2B(1) = 16
fslen = 0
...
/* Merge in any relevant extents from the meta_list */
list_for_each_entry_safe(p, tmp, &info->gfi_meta_list, fmr_list) {
...
// since fsb = 16, considers all metadata which starts before 16 blockno
iter 1: error = ext4_getfsmap_helper(sb, info, p); // p = sb (0,1), nop
info->gfi_next_fsblk = 1
iter 2: error = ext4_getfsmap_helper(sb, info, p); // p = gdt (1,2), nop
info->gfi_next_fsblk = 2
iter 3: error = ext4_getfsmap_helper(sb, info, p); // p = blk bitmap (2,3), nop
info->gfi_next_fsblk = 3
iter 4: error = ext4_getfsmap_helper(sb, info, p); // p = ino bitmap (18,19)
if (rec_blk > info->gfi_next_fsblk) { // (18 > 3)
// emits an extra entry ** BUG **
}
}
Fix this by directly calling ext4_getfsmap_datadev() with a dummy
record that has fmr_physical set to (end_fsb + 1) instead of
last_cluster + 1. By using the block instead of cluster we get the
correct behavior.
Replacing ext4_getfsmap_datadev_helper() with ext4_getfsmap_helper()
is okay since the gfi_lastfree and metadata checks in
ext4_getfsmap_datadev_helper() are anyways redundant when we only want
to emit the last allocated block of the range, as we have already
taken care of emitting metadata and any last free blocks.
The check for a fast symlink in the presence of only an
external xattr inode is incorrect. If a fast symlink does
not have an xattr block (i_file_acl == 0), but does have
an external xattr inode that increases inode i_blocks, then
the check for a fast symlink will incorrectly fail and
__ext4_iget()->ext4_ind_check_inode() will report the inode
is corrupt when it "validates" i_data[] on the next read:
(note that "block 7303014" = 0x6f6f66 = "foo" in LE order).
ext4_inode_is_fast_symlink() should check the superblock
EXT4_FEATURE_INCOMPAT_EA_INODE feature flag, not the inode
EXT4_EA_INODE_FL, since the latter is only set on the xattr
inode itself, and not on the inode that uses this xattr.
Cc: stable@vger.kernel.org Fixes: fc82228a5e38 ("ext4: support fast symlinks from ext3 file systems") Signed-off-by: Andreas Dilger <adilger@whamcloud.com> Reviewed-by: Li Dongyang <dongyangli@ddn.com> Reviewed-by: Alex Zhuravlev <bzzz@whamcloud.com> Reviewed-by: Oleg Drokin <green@whamcloud.com>
Reviewed-on: https://review.whamcloud.com/59879
Lustre-bug-id: https://jira.whamcloud.com/browse/LU-19121 Link: https://patch.msgid.link/20250717063709.757077-1-adilger@dilger.ca Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IMA testing revealed that after an ext4 remount, file accesses triggered
full measurements even without modifications, instead of skipping as
expected when i_version is unchanged.
Debugging showed `SB_I_VERSION` was cleared in reconfigure_super() during
remount due to commit 1ff20307393e ("ext4: unconditionally enable the
i_version counter") removing the fix from commit 960e0ab63b2e ("ext4: fix
i_version handling on remount").
To rectify this, `SB_I_VERSION` is always set for `fc->sb_flags` in
ext4_init_fs_context(), instead of `sb->s_flags` in __ext4_fill_super(),
ensuring it persists across all mounts.
Cc: stable@kernel.org Fixes: 1ff20307393e ("ext4: unconditionally enable the i_version counter") Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://patch.msgid.link/20250703073903.6952-2-libaokun@huaweicloud.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the connection tracking logic to handle both IPv4 and IPv6
address families.
Cc: stable@vger.kernel.org Fixes: e6bb91939740 ("ksmbd: limit repeated connections from clients with the same IP") Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ksmbd_conn_releasing(opinfo->conn) returns true,the refcount was not
decremented properly, causing a refcount leak that prevents the count from
reaching zero and the memory from being released.
Cc: stable@vger.kernel.org Signed-off-by: Ziyan Xu <ziyan@securitygossip.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
