During firmware download the device expects memory addresses in
big-endian byte order. As the wIndex parameter which hold the address is
sent in little-endian byte order regardless of host byte order, we need
to use swab16 rather than cpu_to_be16.
Also make sure to handle the struct ti_i2c_desc size parameter which is
returned in little-endian byte order.
Fix driver new_id sysfs-attribute removal deadlock by making sure to
not hold any locks that the attribute operations grab when removing the
attribute.
Specifically, usb_serial_deregister holds the table mutex when
deregistering the driver, which includes removing the new_id attribute.
This can lead to a deadlock as writing to new_id increments the
attribute's active count before trying to grab the same mutex in
usb_serial_probe.
The deadlock can easily be triggered by inserting a sleep in
usb_serial_deregister and writing the id of an unbound device to new_id
during module unload.
As the table mutex (in this case) is used to prevent subdriver unload
during probe, it should be sufficient to only hold the lock while
manipulating the usb-serial driver list during deregister. A racing
probe will then either fail to find a matching subdriver or fail to get
the corresponding module reference.
Since v3.15-rc1 this also triggers the following lockdep warning:
======================================================
[ INFO: possible circular locking dependency detected ]
3.15.0-rc2 #123 Tainted: G W
-------------------------------------------------------
modprobe/190 is trying to acquire lock:
(s_active#4){++++.+}, at: [<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
but task is already holding lock:
(table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Fix regression introduced by commit 8e493ca1767d ("USB: usb_wwan: fix
bulk-urb allocation") by making sure to require both bulk-in and out
endpoints during port probe.
The original option driver (which usb_wwan is based on) was written
under the assumption that either endpoint could be missing, but
evidently this cannot have been tested properly. Specifically, it would
handle opening a device without bulk-in (but would blow up during resume
which was implemented later), but not a missing bulk-out in write()
(although it is handled in some places such as write_room()).
Fortunately (?), the driver also got the test for missing endpoints
wrong so the urbs were in fact always allocated, although they would be
initialised using the wrong endpoint address (0) and any submission of
such an urb would fail.
The commit mentioned above fixed the test for missing endpoints but
thereby exposed the other bugs which would now generate null-pointer
exceptions rather than failed urb submissions.
The regression was introduced in v3.7, but the offending commit was also
marked for stable.
By specifying NO_UNION_NORMAL the ACM driver does only use the first two
USB interfaces (modem data & control). The AT Port, Diagnostic and NMEA
interfaces are left to the USB serial driver.
Signed-off-by: Michael Ulbricht <michael.ulbricht@systec-electronic.com> Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
David Vrabel identified a regression when using automatic NUMA balancing
under Xen whereby page table entries were getting corrupted due to the
use of native PTE operations. Quoting him
Xen PV guest page tables require that their entries use machine
addresses if the preset bit (_PAGE_PRESENT) is set, and (for
successful migration) non-present PTEs must use pseudo-physical
addresses. This is because on migration MFNs in present PTEs are
translated to PFNs (canonicalised) so they may be translated back
to the new MFN in the destination domain (uncanonicalised).
pte_mknonnuma(), pmd_mknonnuma(), pte_mknuma() and pmd_mknuma()
set and clear the _PAGE_PRESENT bit using pte_set_flags(),
pte_clear_flags(), etc.
In a Xen PV guest, these functions must translate MFNs to PFNs
when clearing _PAGE_PRESENT and translate PFNs to MFNs when setting
_PAGE_PRESENT.
His suggested fix converted p[te|md]_[set|clear]_flags to using
paravirt-friendly ops but this is overkill. He suggested an alternative
of using p[te|md]_modify in the NUMA page table operations but this is
does more work than necessary and would require looking up a VMA for
protections.
This patch modifies the NUMA page table operations to use paravirt
friendly operations to set/clear the flags of interest. Unfortunately
this will take a performance hit when updating the PTEs on
CONFIG_PARAVIRT but I do not see a way around it that does not break
Xen.
Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: David Vrabel <david.vrabel@citrix.com> Tested-by: David Vrabel <david.vrabel@citrix.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Anvin <hpa@zytor.com> Cc: Fengguang Wu <fengguang.wu@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Steven Noonan <steven@uplinklabs.net> Cc: Rik van Riel <riel@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: Cyrill Gorcunov <gorcunov@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
soft lockup in freeing gigantic hugepage fixed in commit 55f67141a892 "mm:
hugetlb: fix softlockup when a large number of hugepages are freed." can
happen in return_unused_surplus_pages(), so let's fix it.
When performing a user-request check/repair (MD_RECOVERY_REQUEST is set)
on a raid1, we allocate multiple bios each with their own set of pages.
If the page allocations for one bio fails, we currently do *not* free
the pages allocated for the previous bios, nor do we free the bio itself.
This patch frees all the already-allocate pages, and makes sure that
all the bios are freed as well.
This bug can cause a memory leak which can ultimately OOM a machine.
It was introduced in 3.10-rc1.
Fixes: a07876064a0b73ab5ef1ebcf14b1cf0231c07858 Cc: Kent Overstreet <koverstreet@google.com> Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The Microsoft Surface Type/Touch Cover 2 is a fancy device which advertised
itself as a multitouch device but with constant input reports.
This way, hid_scan_report() gives the group MULTITOUCH to it, but
hid-multitouch can not handle it due to the constant collection ignored
by hid-input.
To prevent such crap in the future, and while we do not fix this particular
device, make the scan_report coherent with hid-input.c, and ignore constant
input reports.
The git commit a945928ea2709bc0e8e8165d33aed855a0110279
('xen: Do not enable spinlocks before jump_label_init() has executed')
was added to deal with the jump machinery. Earlier the code
that turned on the jump label was only called by Xen specific
functions. But now that it had been moved to the initcall machinery
it gets called on Xen, KVM, and baremetal - ouch!. And the detection
machinery to only call it on Xen wasn't remembered in the heat
of merge window excitement.
This means that the slowpath is enabled on baremetal while it should
not be.
Reported-by: Waiman Long <waiman.long@hp.com> Acked-by: Steven Rostedt <rostedt@goodmis.org> CC: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Problem reported in Red Hat bz 1040329 for strict writes where we cache
only when we hold oplock and write direct to the server when we don't.
When we receive an oplock break, we first change the oplock value for
the inode in cifsInodeInfo->oplock to indicate that we no longer hold
the oplock before we enqueue a task to flush changes to the backing
device. Once we have completed flushing the changes, we return the
oplock to the server.
There are 2 ways here where we can have data corruption
1) While we flush changes to the backing device as part of the oplock
break, we can have processes write to the file. These writes check for
the oplock, find none and attempt to write directly to the server.
These direct writes made while we are flushing from cache could be
overwritten by data being flushed from the cache causing data
corruption.
2) While a thread runs in cifs_strict_writev, the machine could receive
and process an oplock break after the thread has checked the oplock and
found that it allows us to cache and before we have made changes to the
cache. In that case, we end up with a dirty page in cache when we
shouldn't have any. This will be flushed later and will overwrite all
subsequent writes to the part of the file represented by this page.
Before making any writes to the server, we need to confirm that we are
not in the process of flushing data to the server and if we are, we
should wait until the process is complete before we attempt the write.
We should also wait for existing writes to complete before we process
an oplock break request which changes oplock values.
We add a version specific downgrade_oplock() operation to allow for
differences in the oplock values set for the different smb versions.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: Pavel Shilovsky <piastry@etersoft.ru> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
it's pointless and actually leads to wrong behaviour in at least one
moderately convoluted case (pipe(), close one end, try to get to
another via /proc/*/fd and run into ETXTBUSY).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Doing rbd_obj_request_put() in rbd_img_request_fill() error paths is
not only insufficient, but also triggers an rbd_assert() in
rbd_obj_request_destroy():
Assertion failure in rbd_obj_request_destroy() at line 1867:
rbd_assert(obj_request->img_request == NULL);
rbd_img_obj_request_add() adds obj_requests to the img_request, the
opposite is rbd_img_obj_request_del(). Use it.
All xtables variants suffer from the defect that the copy_to_user()
to copy the counters to user memory may fail after the table has
already been exchanged and thus exposed. Return an error at this
point will result in freeing the already exposed table. Any
subsequent packet processing will result in a kernel panic.
We can't copy the counters before exposing the new tables as we
want provide the counter state after the old table has been
unhooked. Therefore convert this into a silent error.
Cc: Florian Westphal <fw@strlen.de> Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
"len" contains sizeof(nf_ct_ext) and size of extensions. In a worst
case it can contain all extensions. Bellow you can find sizes for all
types of extensions. Their sum is definitely bigger than 256.
I have seen "len" up to 280 and my host has crashes w/o this patch.
The right way to fix this problem is reducing the size of the ecache
extension (4) and Florian is going to do this, but these changes will
be quite large to be appropriate for a stable tree.
Fixes: 5b423f6a40a0 (netfilter: nf_conntrack: fix racy timer handling with reliable) Cc: Pablo Neira Ayuso <pablo@netfilter.org> Cc: Patrick McHardy <kaber@trash.net> Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrey Vagin <avagin@openvz.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
sys_getppid() returns the parent pid of the current process in its own pid
namespace. Since audit filters are based in the init pid namespace, a process
could avoid a filter or trigger an unintended one by being in an alternate pid
namespace or log meaningless information.
Switch to task_ppid_nr() for PPIDs to anchor all audit filters in the
init_pid_ns.
(informed by ebiederman's 6c621b7e) Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In the highly unusual case where two threads are running concurrently through
the scanning code scanning the same target, we run into the situation where
one may allocate the target while the other is still using it. In this case,
because the reap checks for STARGET_CREATED and kills the target without
reference counting, the second thread will do the wrong thing on reap.
Fix this by reference counting even creates and doing the STARGET_CREATED
check in the final put.
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch eliminates the reap_ref and replaces it with a proper kref.
On last put of this kref, the target is removed from visibility in
sysfs. The final call to scsi_target_reap() for the device is done from
__scsi_remove_device() and only if the device was made visible. This
ensures that the target disappears as soon as the last device is gone
rather than waiting until final release of the device (which is often
too long).
Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Add two trivial helpers list_next_entry() and list_prev_entry(), they
can have a lot of users including list.h itself. In fact the 1st one is
already defined in events/core.c and bnx2x_sp.c, so the patch simply
moves the definition to list.h.
When the PXS8 and PHS8 devices show up with PID 0x0053 they will expose both a
QMI port and a WWAN interface.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com> CC: Christian Schmiedl <christian.schmiedl@gemalto.com> CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com> CC: David McCullough <david.mccullough@accelecon.com> Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Raymond Wanyoike <raymond.wanyoike@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Mode setting in the TGA driver is broken for these reasons:
- info->fix.line_length is set just once in tgafb_init_fix function. If
we change videomode, info->fix.line_length is not recalculated - so
the video mode is changed but the screen is corrupted because of wrong
info->fix.line_length.
- info->fix.smem_len is set in tgafb_init_fix to the size of the default
video mode (640x480). If we set a higher resolution,
info->fix.smem_len is smaller than the current screen size, preventing
the userspace program from mapping the framebuffer.
This patch fixes it:
- info->fix.line_length initialization is moved to tgafb_set_par so that
it is recalculated with each mode change.
- info->fix.smem_len is set to a fixed value representing the real
amount of video ram (the values are taken from xfree86 driver).
- add a check to tgafb_check_var to prevent us from setting a videomode
that doesn't fit into videoram.
- in tgafb_register, tgafb_init_fix is moved upwards, to be called
before fb_find_mode (because fb_find_mode already needs the videoram
size set in tgafb_init_fix).
We accidentally declared pid_alive without any extern/inline connotation.
Some platforms were fine with this, some like ia64 and mips were very angry.
If the function is inline, the prototype should be inline!
on ia64:
include/linux/sched.h:1718: warning: 'pid_alive' declared inline after
being called
Signed-off-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Added the functions task_ppid_nr_ns() and task_ppid_nr() to abstract the lookup
of the PPID (real_parent's pid_t) of a process, including rcu locking, in the
arbitrary and init_pid_ns.
This provides an alternative to sys_getppid(), which is relative to the child
process' pid namespace.
(informed by ebiederman's 6c621b7e) Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When being refactored from audit_log_start() to audit_log_task_info(), in
commit e23eb920 the tty and ses fields in the log output got transposed.
Restore to original order to avoid breaking search tools.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
`sdhci_bcm_kona_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
Fixes: 058feb53666f ("mmc: sdhci-bcm-kona: make linker-section warning go away") Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Mayer <markus.mayer@linaro.org> Acked-by: Matt Porter <mporter@linaro.org> Signed-off-by: Chris Ball <chris@printf.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
I got a bug report yesterday from Laszlo Ersek in which he states that
his kvm instance fails to suspend. Laszlo bisected it down to this
commit 1cf7e9c68fe8 ("virtio_blk: blk-mq support") where virtio-blk is
converted to use the blk-mq infrastructure.
After digging a bit, it became clear that the issue was with the queue
drain. blk-mq tracks queue usage in a percpu counter, which is
incremented on request alloc and decremented when the request is freed.
The initial hunt was for an inconsistency in blk-mq, but everything
seemed fine. In fact, the counter only returned crazy values when
suspend was in progress.
When a CPU is unplugged, the percpu counters merges that CPU state with
the general state. blk-mq takes care to register a hotcpu notifier with
the appropriate priority, so we know it runs after the percpu counter
notifier. However, the percpu counter notifier only merges the state
when the CPU is fully gone. This leaves a state transition where the
CPU going away is no longer in the online mask, yet it still holds
private values. This means that in this state, percpu_counter_sum()
returns invalid results, and the suspend then hangs waiting for
abs(dead-cpu-value) requests to complete which of course will never
happen.
Fix this by clearing the state earlier, so we never have a case where
the CPU isn't in online mask but still holds private state. This bug
has been there since forever, I guess we don't have a lot of users where
percpu counters needs to be reliable during the suspend cycle.
Evidently, we created some lockd sockets and then failed to create
others. make_socks then returned an error and we tried to tear down the
svc, but svc->sv_permsocks was not empty so we ended up tripping over
the BUG() in svc_destroy().
Fix this by ensuring that we tear down any live sockets we created when
socket creation is going to return an error.
Fixes: 786185b5f8abefa (SUNRPC: move per-net operations from...) Reported-by: Raphos <raphoszap@laposte.net> Signed-off-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: Stanislav Kinsbursky <skinsbursky@parallels.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
As reported by Tang Chen, Gu Zheng and Yasuaki Isimatsu, the following issues
exist in the aio ring page migration support.
As a result, for example, we have the following problem:
thread 1 | thread 2
|
aio_migratepage() |
|-> take ctx->completion_lock |
|-> migrate_page_copy(new, old) |
| *NOW*, ctx->ring_pages[idx] == old |
|
| *NOW*, ctx->ring_pages[idx] == old
| aio_read_events_ring()
| |-> ring = kmap_atomic(ctx->ring_pages[0])
| |-> ring->head = head; *HERE, write to the old ring page*
| |-> kunmap_atomic(ring);
|
|-> ctx->ring_pages[idx] = new |
| *BUT NOW*, the content of |
| ring_pages[idx] is old. |
|-> release ctx->completion_lock |
As above, the new ring page will not be updated.
Fix this issue, as well as prevent races in aio_ring_setup() by holding
the ring_lock mutex during kioctx setup and page migration. This avoids
the overhead of taking another spinlock in aio_read_events_ring() as Tang's
and Gu's original fix did, pushing the overhead into the migration code.
Note that to handle the nesting of ring_lock inside of mmap_sem, the
migratepage operation uses mutex_trylock(). Page migration is not a 100%
critical operation in this case, so the ocassional failure can be
tolerated. This issue was reported by Sasha Levin.
Based on feedback from Linus, avoid the extra taking of ctx->completion_lock.
Instead, make page migration fully serialised by mapping->private_lock, and
have aio_free_ring() simply disconnect the kioctx from the mapping by calling
put_aio_ring_file() before touching ctx->ring_pages[]. This simplifies the
error handling logic in aio_migratepage(), and should improve robustness.
v4: always do mutex_unlock() in cases when kioctx setup fails.
The code to handle any length SG lists calls edma_resume()
even before edma_start() is called. This is incorrect
because edma_resume() enables edma events on the channel
after which CPU (in edma_start) cannot clear posted
events by writing to ECR (per the EDMA user's guide).
Because of this EDMA transfers fail to start if due
to some reason there is a pending EDMA event registered
even before EDMA transfers are started. This can happen if
an EDMA event is a byproduct of device initialization.
Fix this by calling edma_resume() only if it is not the
first batch of MAX_NR_SG elements.
Without this patch, MMC/SD fails to function on DA850 EVM
with DMA. The behaviour is triggered by specific IP and
this can explain why the issue was not reported before
(example with MMC/SD on AM335x).
Tested on DA850 EVM and AM335x EVM-SK using MMC/SD card.
Cc: Joel Fernandes <joelf@ti.com> Acked-by: Joel Fernandes <joelf@ti.com> Tested-by: Jon Ringle <jringle@gridpoint.com> Tested-by: Alexander Holler <holler@ahsoftware.de> Reported-by: Jon Ringle <jringle@gridpoint.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If unable to ensure_next_mapping() we must add the current bio, which
was removed from the @bios list via bio_list_pop, back to the
deferred_bios list before all the remaining @bios.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The persistent-data library used by dm-thin, dm-cache, etc is
transactional. If anything goes wrong, such as an io error when writing
new metadata or a power failure, then we roll back to the last
transaction.
Atomicity when committing a transaction is achieved by:
a) Never overwriting data from the previous transaction.
b) Writing the superblock last, after all other metadata has hit the
disk.
This commit and the following commit ("dm: take care to copy the space
map roots before locking the superblock") fix a bug associated with (b).
When committing it was possible for the superblock to still be written
in spite of an io error occurring during the preceeding metadata flush.
With these commits we're careful not to take the write lock out on the
superblock until after the metadata flush has completed.
Change the transaction manager's semantics for dm_tm_commit() to assume
all data has been flushed _before_ the single superblock that is passed
in.
As a prerequisite, split the block manager's block unlocking and
flushing by simplifying dm_bm_flush_and_unlock() to dm_bm_flush(). Now
the unlocking must be done separately.
This issue was discovered by forcing io errors at the crucial time
using dm-flakey.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If the discard block size is larger than the cache block size we will
not properly quiesce IO to a region that is about to be discarded. This
results in a race between a cache migration where no copy is needed, and
a write to an adjacent cache block that's within the same large discard
block.
Workaround this by limiting the discard_block_size to cache_block_size.
Also limit the max_discard_sectors to cache_block_size.
A more comprehensive fix that introduces range locking support in the
bio_prison and proper quiescing of a discard range that spans multiple
cache blocks is already in development.
Reported-by: Morgan Mears <Morgan.Mears@netapp.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Joe Thornber <ejt@redhat.com> Acked-by: Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Crash detected on sam5d35 and its pmecc nand ecc controller.
The problem was a call to chip->ecc.hwctl from nand_write_subpage_hwecc
(nand_base.c) when we write a sub page.
chip->ecc.hwctl function is not set when we are using PMECC controller.
As a workaround, set NAND_NO_SUBPAGE_WRITE for PMECC controller in
order to disable sub page access in nand_write_page.
The functions for data copying copyarea_foreward_8bpp and
copyarea_backward_8bpp are buggy, they produce screen corruption.
This patch fixes the functions and moves the logic to one function
"copyarea_8bpp". For simplicity, the function only handles copying that
is aligned on 8 pixes. If we copy an unaligned area, generic function
cfb_copyarea is used.
The scenario here is that someone calls enable_irq_wake() from somewhere
in the code. This will result in the lockdep producing a backtrace as can
be seen below. In my case, this problem is triggered when using the wl1271
(TI WlCore) driver found in drivers/net/wireless/ti/ .
The problem cause is rather obvious from the backtrace, but let's outline
the dependency. enable_irq_wake() grabs the IRQ buslock in irq_set_irq_wake(),
which in turns calls mxs_gpio_set_wake_irq() . But mxs_gpio_set_wake_irq()
calls enable_irq_wake() again on the one-level-higher IRQ , thus it tries to
grab the IRQ buslock again in irq_set_irq_wake() . Because the spinlock in
irq_set_irq_wake()->irq_get_desc_buslock()->__irq_get_desc_lock() is not
marked as recursive, lockdep will spew the stuff below.
We know we can safely re-enter the lock, so use IRQ_GC_INIT_NESTED_LOCK to
fix the spew.
=============================================
[ INFO: possible recursive locking detected ] 3.10.33-00012-gf06b763-dirty #61 Not tainted
---------------------------------------------
kworker/0:1/18 is trying to acquire lock:
(&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88
but task is already holding lock:
(&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88
other info that might help us debug this:
Possible unsafe locking scenario:
packet_beacon is not initialized and hence packet_beacon
contains garbage from the stack, so set it to false.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In commit f78bccd79ba3cd9d9664981b501d57bdb81ab8a4 entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8192se.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In commit f78bccd79ba3cd9d9664981b501d57bdb81ab8a4 entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8192cu.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In commit f78bccd79ba3cd9d9664981b501d57bdb81ab8a4 entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8188ee.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In commit f78bccd79ba3cd9d9664981b501d57bdb81ab8a4 entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8723ae.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
A fl->fl_break_time of 0 has a special meaning to the lease break code
that basically means "never break the lease". knfsd uses this to ensure
that leases don't disappear out from under it.
Unfortunately, the code in __break_lease can end up passing this value
to wait_event_interruptible as a timeout, which prevents it from going
to sleep at all. This causes __break_lease to spin in a tight loop and
causes soft lockups.
Fix this by ensuring that we pass a minimum value of 1 as a timeout
instead.
Cc: J. Bruce Fields <bfields@fieldses.org> Reported-by: Terry Barnaby <terry1@beam.ltd.uk> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
qi->tqi_readyTime is written directly to registers that expect
microseconds as unit instead of TU.
When setting the CABQ ready time, cur_conf->beacon_interval is in TU, so
convert it to microseconds before passing it to ath9k_hw.
This should hopefully fix some Tx DMA issues with buffered multicast
frames in AP mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Their power value is initialized to zero. This patch fixes an issue
where the configured power drops to the minimum value when AP_VLAN
interfaces are created/removed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Jouni reported that when doing off-channel transmissions mixed
with on-channel transmissions, the on-channel ones ended up on
the off-channel in some cases.
The reason for that is that during the refactoring of the off-
channel code, I lost the part that stopped all activity and as
a consequence the on-channel frames (including data frames)
were no longer queued but would be transmitted on the temporary
channel.
Fix this by simply restoring the lost activity stop call.
Since Stanislaw's patch removing the quiescing code, mac80211 had
a race regarding suspend vs. authentication: as cfg80211 doesn't
track authentication attempts, it can't abort them. Therefore the
attempts may be kept running while suspending, which can lead to
all kinds of issues, in at least some cases causing an error in
iwlmvm firmware.
Fix this by aborting the authentication attempt when suspending.
commit de74a1d9032f4d37ea453ad2a647e1aff4cd2591
"mac80211: fix WPA with VLAN on AP side with ps-sta"
fixed an issue where queued multicast packets would
be sent out encrypted with the key of an other bss.
commit "7cbf9d017dbb5e3276de7d527925d42d4c11e732"
"mac80211: fix oops on mesh PS broadcast forwarding"
essentially reverted it, because vif.type cannot be AP_VLAN
due to the check to vif.type in ieee80211_get_buffered_bc before.
As the later commit intended to fix the MESH case, fix it
by checking for IFTYPE_AP instead of IFTYPE_AP_VLAN.
Fixes: 7cbf9d017dbb ("mac80211: fix oops on mesh PS broadcast forwarding") Signed-off-by: Michael Braun <michael-dev@fami-braun.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The bss struct might be freed in ieee80211_rx_bss_put(),
so we shouldn't use it afterwards.
Fixes: 817cee7675237 ("mac80211: track AP's beacon rate and give it to the driver") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Crucial/Micron M500 drives properly support queued DSM TRIM starting
with firmware MU05. Update the blacklist so we only disable queued trim
for older firmware releases.
Early M550 series drives suffer from the same issue as M500. A bugfix
firmware is in the pipeline but not ready yet. Until then, blacklist
queued trim for M550.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Chris Samuel <chris@csamuel.org> Cc: Marc MERLIN <marc@merlins.org> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In multiple MSI mode all AHCI ports (including dummy) get assigned
separate MSI vectors and (as result of execution
pci_enable_msi_exact() function) separate IRQ numbers, (mapped to the
MSI vectors).
Therefore, although interrupts from dummy ports are not desired they
are still enabled. We do not request IRQs for dummy ports, but that
only means we do not assign AHCI-specific ISRs to corresponding IRQ
numbers.
As result, dummy port interrupts still could come and traverse all the
way from the PCI device to the kernel, causing unnecessary overhead.
This update disables IRQs for dummy ports and prevents the described
issue.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Tested-by: David Milburn <dmilburn@redhat.com> Cc: linux-ide@vger.kernel.org Fixes: 5ca72c4f7c41 ("AHCI: Support multiple MSIs") Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The AHCI spec allows implementations to issue commands in tag order
rather than FIFO order:
5.3.2.12 P:SelectCmd
HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1)
or HBA selects the command to issue that has had the
PxCI bit set to '1' longer than any other command
pending to be issued.
The result is that commands posted sequentially (time-wise) may play out
of sequence when issued by hardware.
This behavior has likely been hidden by drives that arrange for commands
to complete in issue order. However, it appears recent drives (two from
different vendors that we have found so far) inflict out-of-order
completions as a matter of course. So, we need to take care to maintain
ordered submission, otherwise we risk triggering a drive to fall out of
sequential-io automation and back to random-io processing, which incurs
large latency and degrades throughput.
This issue was found in simple benchmarks where QD=2 seq-write
performance was 30-50% *greater* than QD=32 seq-write performance.
Tagging for -stable and making the change globally since it has a low
risk-to-reward ratio. Also, word is that recent versions of an unnamed
OS also does it this way now. So, drives in the field are already
experienced with this tag ordering scheme.
Cc: Dave Jiang <dave.jiang@intel.com> Cc: Ed Ciechanowski <ed.ciechanowski@intel.com> Reviewed-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
System may crash in ahci_hw_interrupt() or ahci_thread_fn() when
accessing the interrupt status in a port's private_data if the port is
actually a DUMMY port.
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller
This reverts commit e3a8786c10e75903f1269474e21fe8cb49c3a670. While
this commit allows to use the mvneta driver as a module on some
configurations, it breaks other configurations even if mvneta is used
built-in.
This breakage is due to the fact that on some RGMII platforms, the PCS
bit has to be set, and on some other platforms, it has to be
cleared. At the moment, we lack informations to know exactly the
significance of this bit (the datasheet only says "enables PCS"), and
so we can't produce a patch that will work on all platforms at this
point. And since this change is breaking the network completely for
many users, it's much better to revert it for now. We'll come back
later with a proper fix that takes into account all platforms.
Basically:
* Armada XP GP is configured as RGMII-ID, and needs the PCS bit to be
set.
* Armada 370 Mirabox is configured as RGMII-ID, and needs the PCS bit
to be cleared.
And at the moment, we don't know how to make the distinction between
those two cases. One hint is that the Armada XP GP appears in fact to
be using a QSGMII connection with the PHY (Quad-SGMII), but
configuring it as SGMII doesn't work, while RGMII-ID works. This needs
more investigation, but in the mean time, let's unbreak the network
for all those users.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reported-by: Arnaud Ebalard <arno@natisbad.org> Reported-by: Alexander Reuter <Alexander.Reuter@gmx.net> Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=73401 Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch fixes the hardware cursor on mach64 when font width is not a
multiple of 8 pixels.
If you load such a font, the cursor is expanded to the next 8-byte
boundary and a part of the next character after the cursor is not
visible.
For example, when you load a font with 12-pixel width, the cursor width
is 16 pixels and when the cursor is displayed, 4 pixels of the next
character are not visible.
The reason is this: atyfb_cursor is called with proper parameters to
load an image that is 12-pixel wide. However, the number is aligned on
the next 8-pixel boundary on the line
"unsigned int width = (cursor->image.width + 7) >> 3;" and the whole
function acts as it is was loading a 16-pixel image.
This patch fixes it so that the value written to the framebuffer is
padded with 0xaaaa (the transparent pattern) when the image size it not
a multiple of 8 pixels. The transparent pattern causes that the cursor
will not interfere with the next character.
The function cfb_copyarea is buggy when the copy operation is not aligned on
long boundary (4 bytes on 32-bit machines, 8 bytes on 64-bit machines).
How to reproduce:
- use x86-64 machine
- use a framebuffer driver without acceleration (for example uvesafb)
- set the framebuffer to 8-bit depth
(for example fbset -a 1024x768-60 -depth 8)
- load a font with character width that is not a multiple of 8 pixels
note: the console-tools package cannot load a font that has
width different from 8 pixels. You need to install the packages
"kbd" and "console-terminus" and use the program "setfont" to
set font width (for example: setfont Uni2-Terminus20x10)
- move some text left and right on the bash command line and you get a
screen corruption
To expose more bugs, put this line to the end of uvesafb_init_info:
info->flags |= FBINFO_HWACCEL_COPYAREA | FBINFO_READS_FAST;
- Now framebuffer console will use cfb_copyarea for console scrolling.
You get a screen corruption when console is scrolled.
This patch is a rewrite of cfb_copyarea. It fixes the bugs, with this
patch, console scrolling in 8-bit depth with a font width that is not a
multiple of 8 pixels works fine.
The cfb_copyarea code was very buggy and it looks like it was written
and never tried with non-8-pixel font.
There was a very small race window where resume to kernel mode from a
Exception Path (or pure kernel mode which is true for most of ARC
exceptions anyways), was not disabling interrupts in restore_regs,
clobbering the exception regs
Anton found the culprit call flow (after many sleepless nights)
| 1. we got a Trap from user land
| 2. started to service it.
| 3. While doing some stuff on user-land memory (I think it is padzero()),
| we got a DataTlbMiss
| 4. On return from it we are taking "resume_kernel_mode" path
| 5. NEED_RESHED is not set, so we go to "return from exception" path in
| restore regs.
| 6. there seems to be IRQ happening
Commit 9e1fda4ae158 ("ASoC: dapm: Implement mixer input auto-disable")
is trying to free the widget it allocated by snd_soc_dapm_new_control()
call in dapm_kcontrol_data_alloc() by adding kfree(data->widget) to
dapm_kcontrol_free().
This is causing a widget double free with auto-disabled DAPM kcontrols
in sound card unregistration because widgets are already freed before
dapm_kcontrol_free() is called.
Reason for that is all widgets are added into dapm->card->widgets list
in snd_soc_dapm_new_control() and freed in dapm_free_widgets() during
execution of snd_soc_dapm_free().
Now snd_soc_dapm_free() calls for different DAPM contexts happens before
snd_card_free() call from where the call chain to dapm_kcontrol_free()
begins:
The A register needs to be initialized to zero in the prolog if the
first instruction of the BPF program is BPF_S_LDX_B_MSH to prevent
leaking the content of %r5 to user space.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Using a notification type mask for the store event information chsc
is unsupported on some firmware levels. Retry SEI with that mask set
to zero (which is the old way of requesting only channel subsystem
related events).
Reported-and-tested-by: Stefan Haberland <stefan.haberland@de.ibm.com> Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This moves tm_recheckpoint to a C function and moves the tm_restore_sprs into
that function. It then adds IRQ disabling over the trechkpt critical section.
It also sets the TEXASR FS in the signals code to ensure this is never set now
that we explictly write the TM sprs in tm_recheckpoint.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
On suspend, _scsih_suspend calls mpt2sas_base_free_resources, which
in turn calls pci_disable_device if the device is enabled prior to
suspending. However, _scsih_suspend also calls pci_disable_device
itself.
Thus, in the event that the device is enabled prior to suspending,
pci_disable_device will be called twice. This patch removes the
duplicate call to pci_disable_device in _scsi_suspend as it is both
unnecessary and results in a kernel oops.
virtscsi_init calls virtscsi_remove_vqs on err, even before initializing
the vqs. The latter calls virtscsi_set_affinity, so let's check the
pointer there before setting affinity on it.
This fixes a panic when setting device's num_queues=2 on RHEL 6.5:
The original MIPS hibernate code flushes cache and TLB entries in
swsusp_arch_resume(). But they are removed in Commit 44eeab67416711
(MIPS: Hibernation: Remove SMP TLB and cacheflushing code.). A cross-
CPU flush is surely unnecessary because all but the local CPU have
already been disabled. But a local flush (at least the TLB flush) is
needed. When we do hibernation on Loongson-3 with an E1000E NIC, it is
very easy to produce a kernel panic (kernel page fault, or unaligned
access). The root cause is E1000E driver use vzalloc_node() to allocate
pages, the stale TLB entries of the booting kernel will be misused by
the resumed target kernel.
Signed-off-by: Huacai Chen <chenhc@lemote.com> Cc: John Crispin <john@phrozen.org> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6643/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Previously a reserved instruction exception while in guest code would
cause a KVM internal error if kvm_mips_handle_ri() didn't recognise the
instruction (including a RDHWR from an unrecognised hardware register).
However the guest OS should really have the opportunity to catch the
exception so that it can take the appropriate actions such as sending a
SIGILL to the guest user process or emulating the instruction itself.
Therefore in these cases emulate a guest RI exception and only return
EMULATE_FAIL if that fails, being careful to revert the PC first in case
the exception occurred in a branch delay slot in which case the PC will
already point to the branch target.
Also turn the printk messages relating to these cases into kvm_debug
messages so that they aren't usually visible.
This allows crashme to run in the guest without killing the entire VM.
The kvm/mmu code shared by arm and arm64 uses kalloc() to allocate
a bounce page (if hypervisor init code crosses page boundary) and
hypervisor PGDs. The problem is that kalloc() does not guarantee
the proper alignment. In the case of the bounce page, the page sized
buffer allocated may also cross a page boundary negating the purpose
and leading to a hang during kvm initialization. Likewise the PGDs
allocated may not meet the minimum alignment requirements of the
underlying MMU. This patch uses __get_free_page() to guarantee the
worst case alignment needs of the bounce page and PGDs on both arm
and arm64.
Signed-off-by: Mark Salter <msalter@redhat.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When dispatch SGI(mode == 0), that is the vcpu of VM should send
sgi to the cpu which the target_cpus list.
So, there must add the "break" to branch of case 0.
Signed-off-by: Haibin Wang <wanghaibin.wang@huawei.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Do not leak kernel-only floppy_raw_cmd structure members to userspace.
This includes the linked-list pointer and the pointer to the allocated
DMA space.
projects / people / ms / linux.git / log
