net: stmmac: fix dwmac1000 ptp timestamp status offset
When a PTP interrupt occurs, the driver accesses the wrong offset to
learn about the number of available snapshots in the FIFO for dwmac1000:
it should be accessing bits 29..25, while it is currently reading bits
19..16 (those are bits about the auxiliary triggers which have generated
the timestamps). As a consequence, it does not compute correctly the
number of available snapshots, and so possibly do not generate the
corresponding clock events if the bogus value ends up being 0.
Fix clock events generation by reading the correct bits in the timestamp
register for dwmac1000.
Shannon Nelson [Mon, 21 Apr 2025 17:46:06 +0000 (10:46 -0700)]
pds_core: make wait_context part of q_info
Make the wait_context a full part of the q_info struct rather
than a stack variable that goes away after pdsc_adminq_post()
is done so that the context is still available after the wait
loop has given up.
There was a case where a slow development firmware caused
the adminq request to time out, but then later the FW finally
finished the request and sent the interrupt. The handler tried
to complete_all() the completion context that had been created
on the stack in pdsc_adminq_post() but no longer existed.
This caused bad pointer usage, kernel crashes, and much wailing
and gnashing of teeth.
Fixes: 01ba61b55b20 ("pds_core: Add adminq processing and commands") Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250421174606.3892-5-shannon.nelson@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pds_core: Remove unnecessary check in pds_client_adminq_cmd()
When the pds_core driver was first created there were some race
conditions around using the adminq, especially for client drivers.
To reduce the possibility of a race condition there's a check
against pf->state in pds_client_adminq_cmd(). This is problematic
for a couple of reasons:
1. The PDSC_S_INITING_DRIVER bit is set during probe, but not
cleared until after everything in probe is complete, which
includes creating the auxiliary devices. For pds_fwctl this
means it can't make any adminq commands until after pds_core's
probe is complete even though the adminq is fully up by the
time pds_fwctl's auxiliary device is created.
2. The race conditions around using the adminq have been fixed
and this path is already protected against client drivers
calling pds_client_adminq_cmd() if the adminq isn't ready,
i.e. see pdsc_adminq_post() -> pdsc_adminq_inc_if_up().
Fix this by removing the pf->state check in pds_client_adminq_cmd()
because invalid accesses to pds_core's adminq is already handled by
pdsc_adminq_post()->pdsc_adminq_inc_if_up().
Fixes: 10659034c622 ("pds_core: add the aux client API") Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250421174606.3892-4-shannon.nelson@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pds_core: handle unsupported PDS_CORE_CMD_FW_CONTROL result
If the FW doesn't support the PDS_CORE_CMD_FW_CONTROL command
the driver might at the least print garbage and at the worst
crash when the user runs the "devlink dev info" devlink command.
This happens because the stack variable fw_list is not 0
initialized which results in fw_list.num_fw_slots being a
garbage value from the stack. Then the driver tries to access
fw_list.fw_names[i] with i >= ARRAY_SIZE and runs off the end
of the array.
Fix this by initializing the fw_list and by not failing
completely if the devcmd fails because other useful information
is printed via devlink dev info even if the devcmd fails.
Fixes: 45d76f492938 ("pds_core: set up device and adminq") Signed-off-by: Brett Creeley <brett.creeley@amd.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250421174606.3892-3-shannon.nelson@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pds_core: Prevent possible adminq overflow/stuck condition
The pds_core's adminq is protected by the adminq_lock, which prevents
more than 1 command to be posted onto it at any one time. This makes it
so the client drivers cannot simultaneously post adminq commands.
However, the completions happen in a different context, which means
multiple adminq commands can be posted sequentially and all waiting
on completion.
On the FW side, the backing adminq request queue is only 16 entries
long and the retry mechanism and/or overflow/stuck prevention is
lacking. This can cause the adminq to get stuck, so commands are no
longer processed and completions are no longer sent by the FW.
As an initial fix, prevent more than 16 outstanding adminq commands so
there's no way to cause the adminq from getting stuck. This works
because the backing adminq request queue will never have more than 16
pending adminq commands, so it will never overflow. This is done by
reducing the adminq depth to 16.
Fixes: 45d76f492938 ("pds_core: set up device and adminq") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250421174606.3892-2-shannon.nelson@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Golle [Tue, 22 Apr 2025 03:10:20 +0000 (04:10 +0100)]
net: dsa: mt7530: sync driver-specific behavior of MT7531 variants
MT7531 standalone and MMIO variants found in MT7988 and EN7581 share
most basic properties. Despite that, assisted_learning_on_cpu_port and
mtu_enforcement_ingress were only applied for MT7531 but not for MT7988
or EN7581, causing the expected issues on MMIO devices.
Apply both settings equally also for MT7988 and EN7581 by moving both
assignments form mt7531_setup() to mt7531_setup_common().
This fixes unwanted flooding of packets due to unknown unicast
during DA lookup, as well as issues with heterogenous MTU settings.
====================
net_sched: Fix UAF vulnerability in HFSC qdisc
This patchset contains two bug fixes and a selftest for the first one
which we have a reliable reproducer, please check each patch
description for details.
====================
Cong Wang [Thu, 17 Apr 2025 18:47:32 +0000 (11:47 -0700)]
selftests/tc-testing: Add test for HFSC queue emptying during peek operation
Add a selftest to exercise the condition where qdisc implementations
like netem or codel might empty the queue during a peek operation.
This tests the defensive code path in HFSC that checks the queue length
again after peeking to handle this case.
Based on the reproducer from Gerrard, improved by Jamal.
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Tested-by: Victor Nogueira <victor@mojatatu.com> Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://patch.msgid.link/20250417184732.943057-4-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cong Wang [Thu, 17 Apr 2025 18:47:30 +0000 (11:47 -0700)]
net_sched: hfsc: Fix a UAF vulnerability in class handling
This patch fixes a Use-After-Free vulnerability in the HFSC qdisc class
handling. The issue occurs due to a time-of-check/time-of-use condition
in hfsc_change_class() when working with certain child qdiscs like netem
or codel.
The vulnerability works as follows:
1. hfsc_change_class() checks if a class has packets (q.qlen != 0)
2. It then calls qdisc_peek_len(), which for certain qdiscs (e.g.,
codel, netem) might drop packets and empty the queue
3. The code continues assuming the queue is still non-empty, adding
the class to vttree
4. This breaks HFSC scheduler assumptions that only non-empty classes
are in vttree
5. Later, when the class is destroyed, this can lead to a Use-After-Free
The fix adds a second queue length check after qdisc_peek_len() to verify
the queue wasn't emptied.
Fixes: 21f4d5cc25ec ("net_sched/hfsc: fix curve activation in hfsc_change_class()") Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg> Reviewed-by: Konstantin Khlebnikov <koct9i@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://patch.msgid.link/20250417184732.943057-2-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
selftests: mptcp: diag: use mptcp_lib_get_info_value
When running diag.sh in a loop, chk_dump_one will report the following
"grep: write error":
13 ....chk 2 cestab [ OK ]
grep: write error
14 ....chk dump_one [ OK ]
15 ....chk 2->0 msk in use after flush [ OK ]
16 ....chk 2->0 cestab after flush [ OK ]
This error is caused by a broken pipe. When the output of 'ss' is processed
by grep, 'head -n 1' will exit immediately after getting the first line,
causing the subsequent pipe to close. At this time, if 'grep' is still
trying to write data to the closed pipe, it will trigger a SIGPIPE signal,
causing a write error.
One solution is not to use this problematic "head -n 1" command, but to use
mptcp_lib_get_info_value() helper defined in mptcp_lib.sh to get the value
of 'token'.
Fixes: ba2400166570 ("selftests: mptcp: add a test for mptcp_diag_dump_one") Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Tested-by: Gang Yan <yangang@kylinos.cn> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20250421-net-mptcp-pm-defer-freeing-v1-2-e731dc6e86b9@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mat Martineau [Mon, 21 Apr 2025 17:07:13 +0000 (19:07 +0200)]
mptcp: pm: Defer freeing of MPTCP userspace path manager entries
When path manager entries are deleted from the local address list, they
are first unlinked from the address list using list_del_rcu(). The
entries must not be freed until after the RCU grace period, but the
existing code immediately frees the entry.
Use kfree_rcu_mightsleep() and adjust sk_omem_alloc in open code instead
of using the sock_kfree_s() helper. This code path is only called in a
netlink handler, so the "might sleep" function is preferable to adding
a rarely-used rcu_head member to struct mptcp_pm_addr_entry.
Fixes: 88d097316371 ("mptcp: drop free_list for deleting entries") Cc: stable@vger.kernel.org Signed-off-by: Mat Martineau <martineau@kernel.org> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20250421-net-mptcp-pm-defer-freeing-v1-1-e731dc6e86b9@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change hardware configuration for the NETSYSv3.
- Enable PSE dummy page mechanism for the GDM1/2/3
- Enable PSE drop mechanism when the WDMA Rx ring full
- Enable PSE no-drop mechanism for packets from the WDMA Tx
- Correct PSE free drop threshold
- Correct PSE CDMA high threshold
There is a racing condition between workqueue created when enabling
bearer and another thread created when disabling bearer right after
that as follow:
virtio-net: disable delayed refill when pausing rx
When pausing rx (e.g. set up xdp, xsk pool, rx resize), we call
napi_disable() on the receive queue's napi. In delayed refill_work, it
also calls napi_disable() on the receive queue's napi. When
napi_disable() is called on an already disabled napi, it will sleep in
napi_disable_locked while still holding the netdev_lock. As a result,
later napi_enable gets stuck too as it cannot acquire the netdev_lock.
This leads to refill_work and the pause-then-resume tx are stuck
altogether.
This scenario can be reproducible by binding a XDP socket to virtio-net
interface without setting up the fill ring. As a result, try_fill_recv
will fail until the fill ring is set up and refill_work is scheduled.
This commit adds virtnet_rx_(pause/resume)_all helpers and fixes up the
virtnet_rx_resume to disable future and cancel all inflights delayed
refill_work before calling napi_disable() to pause the rx.
Fixes: 413f0271f396 ("net: protect NAPI enablement with netdev_lock()") Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://patch.msgid.link/20250417072806.18660-2-minhquangbui99@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Qingfang Deng [Thu, 17 Apr 2025 03:25:56 +0000 (11:25 +0800)]
net: phy: leds: fix memory leak
A network restart test on a router led to an out-of-memory condition,
which was traced to a memory leak in the PHY LED trigger code.
The root cause is misuse of the devm API. The registration function
(phy_led_triggers_register) is called from phy_attach_direct, not
phy_probe, and the unregister function (phy_led_triggers_unregister)
is called from phy_detach, not phy_remove. This means the register and
unregister functions can be called multiple times for the same PHY
device, but devm-allocated memory is not freed until the driver is
unbound.
This also prevents kmemleak from detecting the leak, as the devm API
internally stores the allocated pointer.
Fix this by replacing devm_kzalloc/devm_kcalloc with standard
kzalloc/kcalloc, and add the corresponding kfree calls in the unregister
path.
Fixes: 3928ee6485a3 ("net: phy: leds: Add support for "link" trigger") Fixes: 2e0bc452f472 ("net: phy: leds: add support for led triggers on phy link state change") Signed-off-by: Hao Guan <hao.guan@siflower.com.cn> Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250417032557.2929427-1-dqfext@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As a result of an email from the fbnic author, I reviewed the phylink
documentation, and I have decided to clarify the wording in the
mac_link_(up|down)() kernel documentation as this was written from the
point of view of mvneta/mvpp2 and is misleading.
The documentation talks about forcing the link - indeed, this is what
is done in the mvneta and mvpp2 drivers but not at the physical layer
but the MACs idea, which has the effect of only allowing or stopping
packet flow at the MAC. This "link" needs to be controlled when using
a PHY or fixed link to start or stop packet flow at the MAC. However,
as the MAC and PCS are tightly integrated, if the MACs idea of the
link is forced down, it has the side effect that there is no way to
determine that the media link has come up - in this mode, the MAC must
be allowed to follow its built-in PCS so we can read the link state.
Frame the documentation in more generic terms, to avoid the thought
that the physical media link to the partner needs in some way to be
forced up or down with these calls; it does not. If that were to be
done, it would be a self-fulfilling prophecy - e.g. if the media link
goes down, then mac_link_down() will be called, and if the media link
is then placed into a forced down state, there is no possibility
that the media link will ever come up again - clearly this is a wrong
interpretation.
These methods are notifications to the MAC about what has happened to
the media link state - either from the PHY, or a PCS, or whatever
mechanism fixed-link is using. Thus, reword them to get away from
talking about changing link state to avoid confusion with media link
state.
This is not a change of any requirements of these methods.
Also, remove the obsolete references to EEE for these methods, we now
have the LPI functions for configuring the EEE parameters which
renders this redundant, and also makes the passing of "phy" to the
mac_link_up() function obsolete.
net: phylink: fix suspend/resume with WoL enabled and link down
When WoL is enabled, we update the software state in phylink to
indicate that the link is down, and disable the resolver from
bringing the link back up.
On resume, we attempt to bring the overall state into consistency
by calling the .mac_link_down() method, but this is wrong if the
link was already down, as phylink strictly orders the .mac_link_up()
and .mac_link_down() methods - and this would break that ordering.
Fixes: f97493657c63 ("net: phylink: add suspend/resume support") Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Tested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1u55Qf-0016RN-PA@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In lwtunnel_{output|xmit}(), dev_xmit_recursion() may be called in
preemptible scope for PREEMPT kernels. This patch disables BHs before
calling dev_xmit_recursion(). BHs are re-enabled only at the end, since
we must ensure the same CPU is used for both dev_xmit_recursion_inc()
and dev_xmit_recursion_dec() (and any other recursion levels in some
cases) in order to maintain valid per-cpu counters.
net: phy: microchip: force IRQ polling mode for lan88xx
With lan88xx based devices the lan78xx driver can get stuck in an
interrupt loop while bringing the device up, flooding the kernel log
with messages like the following:
lan78xx 2-3:1.0 enp1s0u3: kevent 4 may have been dropped
Removing interrupt support from the lan88xx PHY driver forces the
driver to use polling instead, which avoids the problem.
The issue has been observed with Raspberry Pi devices at least since
4.14 (see [1], bug report for their downstream kernel), as well as
with Nvidia devices [2] in 2020, where disabling interrupts was the
vendor-suggested workaround (together with the claim that phylib
changes in 4.9 made the interrupt handling in lan78xx incompatible).
Iperf reports well over 900Mbits/sec per direction with client in
--dualtest mode, so there does not seem to be a significant impact on
throughput (lan88xx device connected via switch to the peer).
====================
ENETC bug fixes for bpf_xdp_adjust_head() and bpf_xdp_adjust_tail()
It has been reported that on the ENETC driver, bpf_xdp_adjust_head()
and bpf_xdp_adjust_tail() are broken in combination with the XDP_PASS
verdict. I have constructed a series a simple XDP programs and tested
with various packet sizes and confirmed that this is the case.
Patch 3/3 fixes the core issue, which is that the sk_buff created on
XDP_PASS is created by the driver as if XDP never ran, but in fact the
geometry needs to be adjusted according to the delta applied by the
program on the original xdp_buff. It depends on commit 539c1fba1ac7
("xdp: add generic xdp_build_skb_from_buff()") which is not available in
"stable" but perhaps should be.
Patch 2/3 is a small refactor necessary for 3/3.
Patch 1/3 fixes a related issue I noticed, which is that
bpf_xdp_adjust_tail() with a positive offset works for linear XDP
buffers, but returns an error for non-linear ones, even if there is
plenty of space in the final page fragment.
====================
Vladimir Oltean [Thu, 17 Apr 2025 12:00:05 +0000 (15:00 +0300)]
net: enetc: fix frame corruption on bpf_xdp_adjust_head/tail() and XDP_PASS
Vlatko Markovikj reported that XDP programs attached to ENETC do not
work well if they use bpf_xdp_adjust_head() or bpf_xdp_adjust_tail(),
combined with the XDP_PASS verdict. A typical use case is to add or
remove a VLAN tag.
The resulting sk_buff passed to the stack is corrupted, because the
algorithm used by the driver for XDP_PASS is to unwind the current
buffer pointer in the RX ring and to re-process the current frame with
enetc_build_skb() as if XDP hadn't run. That is incorrect because XDP
may have modified the geometry of the buffer, which we then are
completely unaware of. We are looking at a modified buffer with the
original geometry.
The initial reaction, both from me and from Vlatko, was to shop around
the kernel for code to steal that would calculate a delta between the
old and the new XDP buffer geometry, and apply that to the sk_buff too.
We noticed that veth and generic xdp have such code.
The headroom adjustment is pretty uncontroversial, but what turned out
severely problematic is the tailroom.
veth has this snippet:
__skb_put(skb, off); /* positive on grow, negative on shrink */
which on first sight looks decent enough, except __skb_put() takes an
"unsigned int" for the second argument, and the arithmetic seems to only
work correctly by coincidence. Second issue, __skb_put() contains a
SKB_LINEAR_ASSERT(). It's not a great pattern to make more widespread.
The skb may still be nonlinear at that point - it only becomes linear
later when resetting skb->data_len to zero.
To avoid the above, bpf_prog_run_generic_xdp() does this instead:
skb_set_tail_pointer(skb, xdp->data_end - xdp->data);
skb->len += off; /* positive on grow, negative on shrink */
which is more open-coded, uses lower-level functions and is in general a
bit too much to spread around in driver code.
Then there is the snippet:
if (xdp_buff_has_frags(xdp))
skb->data_len = skb_shinfo(skb)->xdp_frags_size;
else
skb->data_len = 0;
One would have expected __pskb_trim() to be the function of choice for
this task. But it's not used in veth/xdpgeneric because the extraneous
fragments were _already_ freed by bpf_xdp_adjust_tail() ->
bpf_xdp_frags_shrink_tail() -> ... -> __xdp_return() - the backing
memory for the skb frags and the xdp frags is the same, but they don't
keep individual references.
In fact, that is the biggest reason why this snippet cannot be reused
as-is, because ENETC temporarily constructs an skb with the original len
and the original number of frags. Because the extraneous frags are
already freed by bpf_xdp_adjust_tail() and returned to the page
allocator, it means the entire approach of using enetc_build_skb() is
questionable for XDP_PASS. To avoid that, one would need to elevate the
page refcount of all frags before calling bpf_prog_run_xdp() and drop it
after XDP_PASS.
There are other things that are missing in ENETC's handling of XDP_PASS,
like for example updating skb_shinfo(skb)->meta_len.
These are all handled correctly and cleanly in commit 539c1fba1ac7
("xdp: add generic xdp_build_skb_from_buff()"), added to net-next in
Dec 2024, and in addition might even be quicker that way. I have a very
strong preference towards backporting that commit for "stable", and that
is what is used to fix the handling bugs. It is way too messy to go
this deep into the guts of an sk_buff from the code of a device driver.
Fixes: d1b15102dd16 ("net: enetc: add support for XDP_DROP and XDP_PASS") Reported-by: Vlatko Markovikj <vlatko.markovikj@etas.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Wei Fang <wei.fang@nxp.com> Link: https://patch.msgid.link/20250417120005.3288549-4-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Thu, 17 Apr 2025 12:00:04 +0000 (15:00 +0300)]
net: enetc: refactor bulk flipping of RX buffers to separate function
This small snippet of code ensures that we do something with the array
of RX software buffer descriptor elements after passing the skb to the
stack. In this case, we see if the other half of the page is reusable,
and if so, we "turn around" the buffers, making them directly usable by
enetc_refill_rx_ring() without going to enetc_new_page().
We will need to perform this kind of buffer flipping from a new code
path, i.e. from XDP_PASS. Currently, enetc_build_skb() does it there
buffer by buffer, but in a subsequent change we will stop using
enetc_build_skb() for XDP_PASS.
Vladimir Oltean [Thu, 17 Apr 2025 12:00:03 +0000 (15:00 +0300)]
net: enetc: register XDP RX queues with frag_size
At the time when bpf_xdp_adjust_tail() gained support for non-linear
buffers, ENETC was already generating this kind of geometry on RX, due
to its use of 2K half page buffers. Frames larger than 1472 bytes
(without FCS) are stored as multi-buffer, presenting a need for multi
buffer support to work properly even in standard MTU circumstances.
Allow bpf_xdp_frags_increase_tail() to know the allocation size of paged
data, so it can safely permit growing the tailroom of the buffer from
XDP programs.
Fixes: bf25146a5595 ("bpf: add frags support to the bpf_xdp_adjust_tail() API") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Wei Fang <wei.fang@nxp.com> Link: https://patch.msgid.link/20250417120005.3288549-2-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xen-netfront: handle NULL returned by xdp_convert_buff_to_frame()
The function xdp_convert_buff_to_frame() may return NULL if it fails
to correctly convert the XDP buffer into an XDP frame due to memory
constraints, internal errors, or invalid data. Failing to check for NULL
may lead to a NULL pointer dereference if the result is used later in
processing, potentially causing crashes, data corruption, or undefined
behavior.
On XDP redirect failure, the associated page must be released explicitly
if it was previously retained via get_page(). Failing to do so may result
in a memory leak, as the pages reference count is not decremented.
Cc: stable@vger.kernel.org # v5.9+ Fixes: 6c5aa6fc4def ("xen networking: add basic XDP support for xen-netfront") Signed-off-by: Alexey Nepomnyashih <sdl@nppct.ru> Link: https://patch.msgid.link/20250417122118.1009824-1-sdl@nppct.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
MAINTAINERS: Update entries for s390 network driver files
Update the entries for s390 network driver files to:
* Add include/linux/ism.h to MAINTAINERS
* Add s390 network driver files to the NETWORKING DRIVERS section
This is to aid developers, and tooling such as get_maintainer.pl alike
to CC patches to all the appropriate people and mailing lists. And is
in keeping with an ongoing effort for NETWORKING entries in MAINTAINERS
to more accurately reflect the way code is maintained.
====================
Simon Horman [Thu, 17 Apr 2025 10:15:02 +0000 (11:15 +0100)]
MAINTAINERS: Add s390 networking drivers to NETWORKING DRIVERS
These files are already correctly covered by the S390 NETWORKING DRIVERS
section. In practice commits for these drivers feed into the Networking
subsystem. So it seems appropriate to also list them under NETWORKING
DRIVERS.
This aids developers, and tooling such as get_maintainer.pl
alike to CC patches to all the appropriate people and mailing lists.
And is in keeping with an ongoing effort for NETWORKING entries
in MAINTAINERS to more accurately reflect the way code is maintained.
Simon Horman [Thu, 17 Apr 2025 10:15:01 +0000 (11:15 +0100)]
MAINTAINERS: Add ism.h to S390 NETWORKING DRIVERS
ism.h appears to be part of s390 networking drivers
so add it to the corresponding section in MAINTAINERS.
This aids developers, and tooling such as get_maintainer.pl
alike to CC patches to the appropriate people and mailing lists.
And is in keeping with an ongoing effort for NETWORKING entries
in MAINTAINERS to more accurately reflect the way code is maintained.
Jakub Kicinski [Fri, 18 Apr 2025 01:53:17 +0000 (18:53 -0700)]
net: fix the missing unlock for detached devices
The combined condition was left as is when we converted
from __dev_get_by_index() to netdev_get_by_index_lock().
There was no need to undo anything with the former, for
the latter we need an unlock.
Henry Martin [Fri, 18 Apr 2025 02:38:14 +0000 (10:38 +0800)]
net/mlx5: Move ttc allocation after switch case to prevent leaks
Relocate the memory allocation for ttc table after the switch statement
that validates params->ns_type in both mlx5_create_inner_ttc_table() and
mlx5_create_ttc_table(). This ensures memory is only allocated after
confirming valid input, eliminating potential memory leaks when invalid
ns_type cases occur.
Fixes: 137f3d50ad2a ("net/mlx5: Support matching on l4_type for ttc_table") Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Link: https://patch.msgid.link/20250418023814.71789-3-bsdhenrymartin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henry Martin [Fri, 18 Apr 2025 02:38:13 +0000 (10:38 +0800)]
net/mlx5: Fix null-ptr-deref in mlx5_create_{inner_,}ttc_table()
Add NULL check for mlx5_get_flow_namespace() returns in
mlx5_create_inner_ttc_table() and mlx5_create_ttc_table() to prevent
NULL pointer dereference.
Fixes: 137f3d50ad2a ("net/mlx5: Support matching on l4_type for ttc_table") Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://patch.msgid.link/20250418023814.71789-2-bsdhenrymartin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MAINTAINERS: Add entry for Socfpga DWMAC ethernet glue driver
Socfpga's DWMAC glue comes in a variety of flavours with multiple
options when it comes to physical interfaces, making it not so easy to
test. Having access to a Cyclone5 with RGMII as well as Lynx PCS
variants, add myself as a maintainer to help with reviews and testing.
- ipv6: add exception routes to GC list in rt6_insert_exception()
- netfilter: conntrack: fix erroneous removal of offload bit
- Bluetooth:
- fix sending MGMT_EV_DEVICE_FOUND for invalid address
- l2cap: process valid commands in too long frame
- btnxpuart: Revert baudrate change in nxp_shutdown
Previous releases - always broken:
- ethtool: fix memory corruption during SFP FW flashing
- eth:
- hibmcge: fixes for link and MTU handling, pause frames etc
- igc: fixes for PTM (PCIe timestamping)
- dsa: b53: enable BPDU reception for management port
Misc:
- fixes for Netlink protocol schemas"
* tag 'net-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (81 commits)
net: ethernet: mtk_eth_soc: revise QDMA packet scheduler settings
net: ethernet: mtk_eth_soc: correct the max weight of the queue limit for 100Mbps
net: ethernet: mtk_eth_soc: reapply mdc divider on reset
net: ti: icss-iep: Fix possible NULL pointer dereference for perout request
net: ti: icssg-prueth: Fix possible NULL pointer dereference inside emac_xmit_xdp_frame()
net: ti: icssg-prueth: Fix kernel warning while bringing down network interface
netfilter: conntrack: fix erronous removal of offload bit
net: don't try to ops lock uninitialized devs
ptp: ocp: fix start time alignment in ptp_ocp_signal_set
net: dsa: avoid refcount warnings when ds->ops->tag_8021q_vlan_del() fails
net: dsa: free routing table on probe failure
net: dsa: clean up FDB, MDB, VLAN entries on unbind
net: dsa: mv88e6xxx: fix -ENOENT when deleting VLANs and MST is unsupported
net: dsa: mv88e6xxx: avoid unregistering devlink regions which were never registered
net: txgbe: fix memory leak in txgbe_probe() error path
net: bridge: switchdev: do not notify new brentries as changed
net: b53: enable BPDU reception for management port
netlink: specs: rt-neigh: prefix struct nfmsg members with ndm
netlink: specs: rt-link: adjust mctp attribute naming
netlink: specs: rtnetlink: attribute naming corrections
...
Merge tag 'for-linus-fwctl' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull fwctl fixes from Jason Gunthorpe:
"Three small changes from further build testing:
- Don't rely on the userspace uuid.h for the uapi header
- Fix sparse warnings in pds
- Typo in log message"
* tag 'for-linus-fwctl' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
fwctl: Fix repeated device word in log message
pds_fwctl: Fix type and endian complaints
fwctl/cxl: Fix uuid_t usage in uapi
Merge tag 'sound-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes. All are device-specific like quirks, new
IDs, and other safe (or rather boring) changes"
* tag 'sound-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
firmware: cs_dsp: test_bin_error: Fix uninitialized data used as fw version
ASoC: codecs: Add of_match_table for aw888081 driver
ASoC: fsl: fsl_qmc_audio: Reset audio data pointers on TRIGGER_START event
mailmap: Add entry for Srinivas Kandagatla
MAINTAINERS: use kernel.org alias
ASoC: cs42l43: Reset clamp override on jack removal
ALSA: hda/realtek - Fixed ASUS platform headset Mic issue
ALSA: hda/cirrus_scodec_test: Don't select dependencies
ALSA: azt2320: Replace deprecated strcpy() with strscpy()
ASoC: hdmi-codec: use RTD ID instead of DAI ID for ELD entry
ASoC: Intel: avs: Constrain path based on BE capabilities
ALSA: hda/tas2781: Remove unnecessary NULL check before release_firmware()
ASoC: Intel: avs: Fix null-ptr-deref in avs_component_probe()
ASoC: fsl_asrc_dma: get codec or cpu dai from backend
ASoC: qcom: Fix sc7280 lpass potential buffer overflow
ASoC: dwc: always enable/disable i2s irqs
ASoC: Intel: sof_sdw: Add quirk for Asus Zenbook S16
ASoC: codecs:lpass-wsa-macro: Fix logic of enabling vi channels
ASoC: codecs:lpass-wsa-macro: Fix vi feedback rate
Merge tag 'platform-drivers-x86-v6.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers fixes from Ilpo Järvinen:
"Fixes:
- amd/pmf: Fix STT limits
- asus-laptop: Fix an uninitialized variable
- intel_pmc_ipc: Allow building without ACPI
- mlxbf-bootctl: Use sysfs_emit_at() in secure_boot_fuse_state_show()
- msi-wmi-platform: Add locking to workaround ACPI firmware bug
New HW support:
- alienware-wmi-wmax:
- Extended thermal control support to:
- Alienware Area-51m R2
- Alienware m16 R1
- Alienware m16 R2
- Dell G16 7630
- Dell G5 5505 SE
- G-Mode support to Alienware m16 R1
- x86-android-tablets: Add Vexia Edu Atla 10 tablet 5V data"
* tag 'platform-drivers-x86-v6.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: msi-wmi-platform: Workaround a ACPI firmware bug
platform/x86: msi-wmi-platform: Rename "data" variable
platform/x86: alienware-wmi-wmax: Extend support to more laptops
platform/x86: alienware-wmi-wmax: Add G-Mode support to Alienware m16 R1
platform/x86: amd: pmf: Fix STT limits
mlxbf-bootctl: use sysfs_emit_at() in secure_boot_fuse_state_show()
platform/x86: x86-android-tablets: Add Vexia Edu Atla 10 tablet 5V data
platform/x86: x86-android-tablets: Add "9v" to Vexia EDU ATLA 10 tablet symbols
asus-laptop: Fix an uninitialized variable
platform/x86: intel_pmc_ipc: add option to build without ACPI
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Small drivers fixes, except for ufs which has two large updates, one
for exposing the device level feature, which is a new addition to the
device spec and the other reworking the exynos driver to fix coherence
issues on some android phones"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: megaraid_sas: Driver version update to 07.734.00.00-rc1
scsi: megaraid_sas: Block zero-length ATA VPD inquiry
scsi: scsi_transport_srp: Replace min/max nesting with clamp()
scsi: ufs: core: Add device level exception support
scsi: ufs: core: Rename ufshcd_wb_presrv_usrspc_keep_vcc_on()
scsi: smartpqi: Use is_kdump_kernel() to check for kdump
scsi: pm80xx: Set phy_attached to zero when device is gone
scsi: ufs: exynos: gs101: Put UFS device in reset on .suspend()
scsi: ufs: exynos: Move phy calls to .exit() callback
scsi: ufs: exynos: Enable PRDT pre-fetching with UFSHCD_CAP_CRYPTO
scsi: ufs: exynos: Ensure consistent phy reference counts
scsi: ufs: exynos: Disable iocc if dma-coherent property isn't set
scsi: ufs: exynos: Move UFS shareability value to drvdata
scsi: ufs: exynos: Ensure pre_link() executes before exynos_ufs_phy_init()
scsi: iscsi: Fix missing scsi_host_put() in error path
scsi: ufs: core: Fix a race condition related to device commands
scsi: hisi_sas: Fix I/O errors caused by hardware port ID changes
scsi: hisi_sas: Enable force phy when SATA disk directly connected
Merge tag 'ata-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fix from Damien Le Moal:
- Fix how sense data from the sense data for successfull NCQ commands
log page is used to fully initialize the result_tf of a completed
command, so that the sense data returned to the scsi layer is fully
initialized with all the device provided information (from Niklas)
* tag 'ata-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-sata: Save all fields from sense data descriptor
Merge tag 'xfs-fixes-6.15-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull XFS fixes from Carlos Maiolino:
"This mostly includes fixes and documentation for the zoned allocator
feature merged during previous merge window, but it also adds a sysfs
tunable for the zone garbage collector.
There is also a fix for a regression to the RT device that we'd like
to fix ASAP now that we're getting more users on the RT zoned
allocator"
* tag 'xfs-fixes-6.15-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: document zoned rt specifics in admin-guide
xfs: fix fsmap for internal zoned devices
xfs: Fix spelling mistake "drity" -> "dirty"
xfs: compute buffer address correctly in xmbuf_map_backing_mem
xfs: add tunable threshold parameter for triggering zone GC
xfs: mark xfs_buf_free as might_sleep()
xfs: remove the leftover xfs_{set,clear}_li_failed infrastructure
Merge tag 'for-6.15-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- handle encoded read ioctl returning EAGAIN so it does not mistakenly
free the work structure
- escape subvolume path in mount option list so it cannot be wrongly
parsed when the path contains ","
- remove folio size assertions when writing super block to device with
enabled large folios
* tag 'for-6.15-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: remove folio order ASSERT()s in super block writeback path
btrfs: correctly escape subvol in btrfs_show_options()
btrfs: ioctl: don't free iov when btrfs_encoded_read() returns -EAGAIN
Merge tag 'slab-for-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab fix from Vlastimil Babka:
- Stable fix adding zero initialization of slab->obj_ext to prevent
crashes with allocation profiling (Suren Baghdasaryan)
* tag 'slab-for-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
slab: ensure slab->obj_exts is clear in a newly allocated slab page
The QDMA packet scheduler suffers from a performance issue.
Fix this by picking up changes from MediaTek's SDK which change to use
Token Bucket instead of Leaky Bucket and fix the SPEED_1000 configuration.
net: ethernet: mtk_eth_soc: reapply mdc divider on reset
In the current method, the MDC divider was reset to the default setting
of 2.5MHz after the NETSYS SER. Therefore, we need to reapply the MDC
divider configuration function in mtk_hw_init() after reset.
Paolo Abeni [Thu, 17 Apr 2025 13:20:41 +0000 (15:20 +0200)]
Merge tag 'nf-25-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fix for net
The following batch contains one Netfilter fix for net:
1) conntrack offload bit is erroneously unset in a race scenario,
from Florian Westphal.
netfilter pull request 25-04-17
* tag 'nf-25-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: conntrack: fix erronous removal of offload bit
====================
Paolo Abeni [Thu, 17 Apr 2025 11:08:41 +0000 (13:08 +0200)]
Merge tag 'for-net-2025-04-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- l2cap: Process valid commands in too long frame
- vhci: Avoid needless snprintf() calls
* tag 'for-net-2025-04-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: vhci: Avoid needless snprintf() calls
Bluetooth: l2cap: Process valid commands in too long frame
====================
====================
Bug fixes from XDP and perout series
This patch series consists of bug fixes from the XDP series:
1. Fixes a kernel warning that occurs when bringing down the
network interface.
2. Resolves a potential NULL pointer dereference in the
emac_xmit_xdp_frame() function.
3. Resolves a potential NULL pointer dereference in the
icss_iep_perout_enable() function
net: ti: icss-iep: Fix possible NULL pointer dereference for perout request
The ICSS IEP driver tracks perout and pps enable state with flags.
Currently when disabling pps and perout signals during icss_iep_exit(),
results in NULL pointer dereference for perout.
To fix the null pointer dereference issue, the icss_iep_perout_enable_hw
function can be modified to directly clear the IEP CMP registers when
disabling PPS or PEROUT, without referencing the ptp_perout_request
structure, as its contents are irrelevant in this case.
Fixes: 9b115361248d ("net: ti: icssg-prueth: Fix clearing of IEP_CMP_CFG registers during iep_init") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/all/7b1c7c36-363a-4085-b26c-4f210bee1df6@stanley.mountain/ Signed-off-by: Meghana Malladi <m-malladi@ti.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250415090543.717991-4-m-malladi@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: ti: icssg-prueth: Fix possible NULL pointer dereference inside emac_xmit_xdp_frame()
There is an error check inside emac_xmit_xdp_frame() function which
is called when the driver wants to transmit XDP frame, to check if
the allocated tx descriptor is NULL, if true to exit and return
ICSSG_XDP_CONSUMED implying failure in transmission.
In this case trying to free a descriptor which is NULL will result
in kernel crash due to NULL pointer dereference. Fix this error handling
and increase netdev tx_dropped stats in the caller of this function
if the function returns ICSSG_XDP_CONSUMED.
Fixes: 62aa3246f462 ("net: ti: icssg-prueth: Add XDP support") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/all/70d8dd76-0c76-42fc-8611-9884937c82f5@stanley.mountain/ Signed-off-by: Meghana Malladi <m-malladi@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250415090543.717991-3-m-malladi@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: ti: icssg-prueth: Fix kernel warning while bringing down network interface
During network interface initialization, the NIC driver needs to register
its Rx queue with the XDP, to ensure the incoming XDP buffer carries a
pointer reference to this info and is stored inside xdp_rxq_info.
While this struct isn't tied to XDP prog, if there are any changes in
Rx queue, the NIC driver needs to stop the Rx queue by unregistering
with XDP before purging and reallocating memory. Drop page_pool destroy
during Rx channel reset as this is already handled by XDP during
xdp_rxq_info_unreg (Rx queue unregister), failing to do will cause the
following warning:
Fixes: 46eeb90f03e0 ("net: ti: icssg-prueth: Use page_pool API for RX buffer allocation") Signed-off-by: Meghana Malladi <m-malladi@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250415090543.717991-2-m-malladi@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
netfilter: conntrack: fix erronous removal of offload bit
The blamed commit exposes a possible issue with flow_offload_teardown():
We might remove the offload bit of a conntrack entry that has been
offloaded again.
1. conntrack entry c1 is offloaded via flow f1 (f1->ct == c1).
2. f1 times out and is pushed back to slowpath, c1 offload bit is
removed. Due to bug, f1 is not unlinked from rhashtable right away.
3. a new packet arrives for the flow and re-offload is triggered, i.e.
f2->ct == c1. This is because lookup in flowtable skip entries with
teardown bit set.
4. Next flowtable gc cycle finds f1 again
5. flow_offload_teardown() is called again for f1 and c1 offload bit is
removed again, even though we have f2 referencing the same entry.
This is harmless, but clearly not correct.
Fix the bug that exposes this: set 'teardown = true' to have the gc
callback unlink the flowtable entry from the table right away instead of
the unintentional defer to the next round.
Also prevent flow_offload_teardown() from fixing up the ct state more than
once: We could also be called from the data path or a notifier, not only
from the flowtable gc callback.
NF_FLOW_TEARDOWN can never be unset, so we can use it as synchronization
point: if we observe did not see a 0 -> 1 transition, then another CPU
is already doing the ct state fixups for us.
Hans Holmberg [Wed, 9 Apr 2025 12:39:56 +0000 (12:39 +0000)]
xfs: document zoned rt specifics in admin-guide
Document the lifetime, nolifetime and max_open_zones mount options
added for zoned rt file systems.
Also add documentation describing the max_open_zones sysfs attribute
exposed in /sys/fs/xfs/<dev>/zoned/
Fixes: 4e4d52075577 ("xfs: add the zoned space allocator") Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Merge tag 'mm-hotfixes-stable-2025-04-16-19-59' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc hotfixes from Andrew Morton:
"31 hotfixes.
9 are cc:stable and the remainder address post-6.15 issues or aren't
considered necessary for -stable kernels.
22 patches are for MM, 9 are otherwise"
* tag 'mm-hotfixes-stable-2025-04-16-19-59' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (31 commits)
MAINTAINERS: update HUGETLB reviewers
mm: fix apply_to_existing_page_range()
selftests/mm: fix compiler -Wmaybe-uninitialized warning
alloc_tag: handle incomplete bulk allocations in vm_module_tags_populate
mailmap: add entry for Jean-Michel Hautbois
mm: (un)track_pfn_copy() fix + doc improvements
mm: fix filemap_get_folios_contig returning batches of identical folios
mm/hugetlb: add a line break at the end of the format string
selftests: mincore: fix tmpfs mincore test failure
mm/hugetlb: fix set_max_huge_pages() when there are surplus pages
mm/cma: report base address of single range correctly
mm: page_alloc: speed up fallbacks in rmqueue_bulk()
kunit: slub: add module description
mm/kasan: add module decription
ucs2_string: add module description
zlib: add module description
fpga: tests: add module descriptions
samples/livepatch: add module descriptions
ASN.1: add module description
mm/vma: add give_up_on_oom option on modify/merge, use in uffd release
...
Jakub Kicinski [Tue, 15 Apr 2025 15:15:52 +0000 (08:15 -0700)]
net: don't try to ops lock uninitialized devs
We need to be careful when operating on dev while in rtnl_create_link().
Some devices (vxlan) initialize netdev_ops in ->newlink, so later on.
Avoid using netdev_lock_ops(), the device isn't registered so we
cannot legally call its ops or generate any notifications for it.
netdev_ops_assert_locked_or_invisible() is safe to use, it checks
registration status first.
Reported-by: syzbot+de1c7d68a10e3f123bdd@syzkaller.appspotmail.com Fixes: 04efcee6ef8d ("net: hold instance lock during NETDEV_CHANGE") Acked-by: Stanislav Fomichev <sdf@fomichev.me> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://patch.msgid.link/20250415151552.768373-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ptp: ocp: fix start time alignment in ptp_ocp_signal_set
In ptp_ocp_signal_set, the start time for periodic signals is not
aligned to the next period boundary. The current code rounds up the
start time and divides by the period but fails to multiply back by
the period, causing misaligned signal starts. Fix this by multiplying
the rounded-up value by the period to ensure the start time is the
closest next period.
Fixes: 4bd46bb037f8e ("ptp: ocp: Use DIV64_U64_ROUND_UP for rounding.") Signed-off-by: Sagi Maimon <maimon.sagi@gmail.com> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://patch.msgid.link/20250415053131.129413-1-maimon.sagi@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 17 Apr 2025 01:14:45 +0000 (18:14 -0700)]
Merge branch 'collection-of-dsa-bug-fixes'
Vladimir Oltean says:
====================
Collection of DSA bug fixes
Prompted by Russell King's 3 DSA bug reports from Friday (linked in
their respective patches: 1, 2 and 3), I am providing fixes to those, as
well as flushing the queue with 2 other bug fixes I had.
1: fix NULL pointer dereference during mv88e6xxx driver unbind, on old
switch models which lack PVT and/or STU. Seen on the ZII dev board
rev B.
2: fix failure to delete bridge port VLANs on old mv88e6xxx chips which
lack STU. Seen on the same board.
3: fix WARN_ON() and resource leak in DSA core on driver unbind. Seen on
the same board but is a much more widespread issue.
4: fix use-after-free during probing of DSA trees with >= 3 switches,
if -EPROBE_DEFER exists. In principle issue also exists for the ZII
board, I reproduced on Turris MOX.
5: fix incorrect use of refcount API in DSA core for those switches
which use tag_8021q (felix, sja1105, vsc73xx). Returning an error
when attempting to delete a tag_8021q VLAN prints a WARN_ON(), which
is harmless but might be problematic with CONFIG_PANIC_ON_OOPS.
====================
Vladimir Oltean [Mon, 14 Apr 2025 21:30:20 +0000 (00:30 +0300)]
net: dsa: avoid refcount warnings when ds->ops->tag_8021q_vlan_del() fails
This is very similar to the problem and solution from commit 232deb3f9567 ("net: dsa: avoid refcount warnings when
->port_{fdb,mdb}_del returns error"), except for the
dsa_port_do_tag_8021q_vlan_del() operation.
Vladimir Oltean [Mon, 14 Apr 2025 21:30:01 +0000 (00:30 +0300)]
net: dsa: free routing table on probe failure
If complete = true in dsa_tree_setup(), it means that we are the last
switch of the tree which is successfully probing, and we should be
setting up all switches from our probe path.
After "complete" becomes true, dsa_tree_setup_cpu_ports() or any
subsequent function may fail. If that happens, the entire tree setup is
in limbo: the first N-1 switches have successfully finished probing
(doing nothing but having allocated persistent memory in the tree's
dst->ports, and maybe dst->rtable), and switch N failed to probe, ending
the tree setup process before anything is tangible from the user's PoV.
If switch N fails to probe, its memory (ports) will be freed and removed
from dst->ports. However, the dst->rtable elements pointing to its ports,
as created by dsa_link_touch(), will remain there, and will lead to
use-after-free if dereferenced.
If dsa_tree_setup_switches() returns -EPROBE_DEFER, which is entirely
possible because that is where ds->ops->setup() is, we get a kasan
report like this:
==================================================================
BUG: KASAN: slab-use-after-free in mv88e6xxx_setup_upstream_port+0x240/0x568
Read of size 8 at addr ffff000004f56020 by task kworker/u8:3/42
The simplest way to fix the bug is to delete the routing table in its
entirety. dsa_tree_setup_routing_table() has no problem in regenerating
it even if we deleted links between ports other than those of switch N,
because dsa_link_touch() first checks whether the port pair already
exists in dst->rtable, allocating if not.
The deletion of the routing table in its entirety already exists in
dsa_tree_teardown(), so refactor that into a function that can also be
called from the tree setup error path.
In my analysis of the commit to blame, it is the one which added
dsa_link elements to dst->rtable. Prior to that, each switch had its own
ds->rtable which is freed when the switch fails to probe. But the tree
is potentially persistent memory.
Vladimir Oltean [Mon, 14 Apr 2025 21:29:30 +0000 (00:29 +0300)]
net: dsa: clean up FDB, MDB, VLAN entries on unbind
As explained in many places such as commit b117e1e8a86d ("net: dsa:
delete dsa_legacy_fdb_add and dsa_legacy_fdb_del"), DSA is written given
the assumption that higher layers have balanced additions/deletions.
As such, it only makes sense to be extremely vocal when those
assumptions are violated and the driver unbinds with entries still
present.
But Ido Schimmel points out a very simple situation where that is wrong:
https://lore.kernel.org/netdev/ZDazSM5UsPPjQuKr@shredder/
(also briefly discussed by me in the aforementioned commit).
Basically, while the bridge bypass operations are not something that DSA
explicitly documents, and for the majority of DSA drivers this API
simply causes them to go to promiscuous mode, that isn't the case for
all drivers. Some have the necessary requirements for bridge bypass
operations to do something useful - see dsa_switch_supports_uc_filtering().
Although in tools/testing/selftests/net/forwarding/local_termination.sh,
we made an effort to popularize better mechanisms to manage address
filters on DSA interfaces from user space - namely macvlan for unicast,
and setsockopt(IP_ADD_MEMBERSHIP) - through mtools - for multicast, the
fact is that 'bridge fdb add ... self static local' also exists as
kernel UAPI, and might be useful to someone, even if only for a quick
hack.
It seems counter-productive to block that path by implementing shim
.ndo_fdb_add and .ndo_fdb_del operations which just return -EOPNOTSUPP
in order to prevent the ndo_dflt_fdb_add() and ndo_dflt_fdb_del() from
running, although we could do that.
Accepting that cleanup is necessary seems to be the only option.
Especially since we appear to be coming back at this from a different
angle as well. Russell King is noticing that the WARN_ON() triggers even
for VLANs:
https://lore.kernel.org/netdev/Z_li8Bj8bD4-BYKQ@shell.armlinux.org.uk/
What happens in the bug report above is that dsa_port_do_vlan_del() fails,
then the VLAN entry lingers on, and then we warn on unbind and leak it.
This is not a straight revert of the blamed commit, but we now add an
informational print to the kernel log (to still have a way to see
that bugs exist), and some extra comments gathered from past years'
experience, to justify the logic.
Vladimir Oltean [Mon, 14 Apr 2025 21:29:13 +0000 (00:29 +0300)]
net: dsa: mv88e6xxx: fix -ENOENT when deleting VLANs and MST is unsupported
Russell King reports that on the ZII dev rev B, deleting a bridge VLAN
from a user port fails with -ENOENT:
https://lore.kernel.org/netdev/Z_lQXNP0s5-IiJzd@shell.armlinux.org.uk/
This comes from mv88e6xxx_port_vlan_leave() -> mv88e6xxx_mst_put(),
which tries to find an MST entry in &chip->msts associated with the SID,
but fails and returns -ENOENT as such.
But we know that this chip does not support MST at all, so that is not
surprising. The question is why does the guard in mv88e6xxx_mst_put()
not exit early:
if (!sid)
return 0;
And the answer seems to be simple: the sid comes from vlan.sid which
supposedly was previously populated by mv88e6xxx_vtu_get().
But some chip->info->ops->vtu_getnext() implementations do not populate
vlan.sid, for example see mv88e6185_g1_vtu_getnext(). In that case,
later in mv88e6xxx_port_vlan_leave() we are using a garbage sid which is
just residual stack memory.
Testing for sid == 0 covers all cases of a non-bridge VLAN or a bridge
VLAN mapped to the default MSTI. For some chips, SID 0 is valid and
installed by mv88e6xxx_stu_setup(). A chip which does not support the
STU would implicitly only support mapping all VLANs to the default MSTI,
so although SID 0 is not valid, it would be sufficient, if we were to
zero-initialize the vlan structure, to fix the bug, due to the
coincidence that a test for vlan.sid == 0 already exists and leads to
the same (correct) behavior.
Another option which would be sufficient would be to add a test for
mv88e6xxx_has_stu() inside mv88e6xxx_mst_put(), symmetric to the one
which already exists in mv88e6xxx_mst_get(). But that placement means
the caller will have to dereference vlan.sid, which means it will access
uninitialized memory, which is not nice even if it ignores it later.
So we end up making both modifications, in order to not rely just on the
sid == 0 coincidence, but also to avoid having uninitialized structure
fields which might get temporarily accessed.
Vladimir Oltean [Mon, 14 Apr 2025 21:28:50 +0000 (00:28 +0300)]
net: dsa: mv88e6xxx: avoid unregistering devlink regions which were never registered
Russell King reports that a system with mv88e6xxx dereferences a NULL
pointer when unbinding this driver:
https://lore.kernel.org/netdev/Z_lRkMlTJ1KQ0kVX@shell.armlinux.org.uk/
The crash seems to be in devlink_region_destroy(), which is not NULL
tolerant but is given a NULL devlink global region pointer.
At least on some chips, some devlink regions are conditionally registered
since the blamed commit, see mv88e6xxx_setup_devlink_regions_global():
if (cond && !cond(chip))
continue;
These are MV88E6XXX_REGION_STU and MV88E6XXX_REGION_PVT. If the chip
does not have an STU or PVT, it should crash like this.
To fix the issue, avoid unregistering those regions which are NULL, i.e.
were skipped at mv88e6xxx_setup_devlink_regions_global() time.
Fixes: 836021a2d0e0 ("net: dsa: mv88e6xxx: Export cross-chip PVT as devlink region") Tested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20250414212850.2953957-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: txgbe: fix memory leak in txgbe_probe() error path
When txgbe_sw_init() is called, memory is allocated for wx->rss_key
in wx_init_rss_key(). However, in txgbe_probe() function, the subsequent
error paths after txgbe_sw_init() don't free the rss_key. Fix that by
freeing it in error path along with wx->mac_table.
Also change the label to which execution jumps when txgbe_sw_init()
fails, because otherwise, it could lead to a double free for rss_key,
when the mac_table allocation fails in wx_sw_init().
Jonas Gorski [Mon, 14 Apr 2025 20:00:20 +0000 (22:00 +0200)]
net: bridge: switchdev: do not notify new brentries as changed
When adding a bridge vlan that is pvid or untagged after the vlan has
already been added to any other switchdev backed port, the vlan change
will be propagated as changed, since the flags change.
This causes the vlan to not be added to the hardware for DSA switches,
since the DSA handler ignores any vlans for the CPU or DSA ports that
are changed.
E.g. the following order of operations would work:
$ ip link add swbridge type bridge vlan_filtering 1 vlan_default_pvid 0
$ ip link set lan1 master swbridge
$ bridge vlan add dev swbridge vid 1 pvid untagged self
$ bridge vlan add dev lan1 vid 1 pvid untagged
but this order would break:
$ ip link add swbridge type bridge vlan_filtering 1 vlan_default_pvid 0
$ ip link set lan1 master swbridge
$ bridge vlan add dev lan1 vid 1 pvid untagged
$ bridge vlan add dev swbridge vid 1 pvid untagged self
Additionally, the vlan on the bridge itself would become undeletable:
$ bridge vlan
port vlan-id
lan1 1 PVID Egress Untagged
swbridge 1 PVID Egress Untagged
$ bridge vlan del dev swbridge vid 1 self
$ bridge vlan
port vlan-id
lan1 1 PVID Egress Untagged
swbridge 1 Egress Untagged
since the vlan was never added to DSA's vlan list, so deleting it will
cause an error, causing the bridge code to not remove it.
Fix this by checking if flags changed only for vlans that are already
brentry and pass changed as false for those that become brentries, as
these are a new vlan (member) from the switchdev point of view.
Since *changed is set to true for becomes_brentry = true regardless of
would_change's value, this will not change any rtnetlink notification
delivery, just the value passed on to switchdev in vlan->changed.
Fixes: 8d23a54f5bee ("net: bridge: switchdev: differentiate new VLANs from changed ones") Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20250414200020.192715-1-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Gorski [Mon, 14 Apr 2025 20:04:34 +0000 (22:04 +0200)]
net: b53: enable BPDU reception for management port
For STP to work, receiving BPDUs is essential, but the appropriate bit
was never set. Without GC_RX_BPDU_EN, the switch chip will filter all
BPDUs, even if an appropriate PVID VLAN was setup.
====================
ynl: avoid leaks in attr override and spec fixes for C
The C rt-link work revealed more problems in existing codegen
and classic netlink specs.
Patches 1 - 4 fix issues with the codegen. Patches 1 and 2 are
pre-requisites for patch 3. Patch 3 fixes leaking memory if user
tries to override already set attr. Patch 4 validates attrs in case
kernel sends something we don't expect.
Remaining patches fix and align the specs. Patch 5 changes nesting,
the rest are naming adjustments.
====================
Jakub Kicinski [Mon, 14 Apr 2025 21:18:51 +0000 (14:18 -0700)]
netlink: specs: rt-neigh: prefix struct nfmsg members with ndm
Attach ndm- to all members of struct nfmsg. We could possibly
use name-prefix just for C, but I don't think we have any precedent
for using name-prefix on structs, and other rtnetlink sub-specs
give full names for fixed header struct members.
Fixes: bc515ed06652 ("netlink: specs: Add a spec for neighbor tables in rtnetlink") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-9-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MCTP attribute naming is inconsistent. In C we have:
IFLA_MCTP_NET,
IFLA_MCTP_PHYS_BINDING,
^^^^
but in YAML:
- mctp-net
- phys-binding
^
no "mctp"
It's unclear whether the "mctp" part of the name is supposed
to be a prefix or part of attribute name. Make it a prefix,
seems cleaner, even tho technically phys-binding was added later.
Fixes: b2f63d904e72 ("doc/netlink: Add spec for rt link messages") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-8-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some attribute names diverge in very minor ways from the C names.
These are most likely typos, and they prevent the C codegen from
working.
Fixes: bc515ed06652 ("netlink: specs: Add a spec for neighbor tables in rtnetlink") Fixes: b2f63d904e72 ("doc/netlink: Add spec for rt link messages") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-7-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 21:18:48 +0000 (14:18 -0700)]
netlink: specs: rt-link: add an attr layer around alt-ifname
alt-ifname attr is directly placed in requests (as an alternative
to ifname) but in responses its wrapped up in IFLA_PROP_LIST
and only there is may be multi-attr. See rtnl_fill_prop_list().
Fixes: b2f63d904e72 ("doc/netlink: Add spec for rt link messages") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-6-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 21:18:47 +0000 (14:18 -0700)]
tools: ynl-gen: make sure we validate subtype of array-nest
ArrayNest AKA indexed-array support currently skips inner type
validation. We count the attributes and then we parse them,
make sure we call validate, too. Otherwise buggy / unexpected
kernel response may lead to crashes.
Fixes: be5bea1cc0bf ("net: add basic C code generators for Netlink") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-5-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 21:18:46 +0000 (14:18 -0700)]
tools: ynl-gen: individually free previous values on double set
When user calls request_attrA_set() multiple times (for the same
attribute), and attrA is of type which allocates memory -
we try to free the previously associated values. For array
types (including multi-attr) we have only freed the array,
but the array may have contained pointers.
Refactor the code generation for free attr and reuse the generated
lines in setters to flush out the previous state. Since setters
are static inlines in the header we need to add forward declarations
for the free helpers of pure nested structs. Track which types get
used by arrays and include the right forwad declarations.
At least ethtool string set and bit set would not be freed without
this. Tho, admittedly, overriding already set attribute twice is likely
a very very rare thing to do.
Fixes: be5bea1cc0bf ("net: add basic C code generators for Netlink") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-4-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 21:18:45 +0000 (14:18 -0700)]
tools: ynl-gen: move local vars after the opening bracket
The "function writing helper" tries to put local variables
between prototype and the opening bracket. Clearly wrong,
but up until now nothing actually uses it to write local
vars so it wasn't noticed.
Jakub Kicinski [Mon, 14 Apr 2025 21:18:44 +0000 (14:18 -0700)]
tools: ynl-gen: don't declare loop iterator in place
The codegen tries to follow the "old" C style and declare loop
iterators at the start of the block / function. Only nested
request handling breaks this style, so adjust it.
cxgb4: fix memory leak in cxgb4_init_ethtool_filters() error path
In the for loop used to allocate the loc_array and bmap for each port, a
memory leak is possible when the allocation for loc_array succeeds,
but the allocation for bmap fails. This is because when the control flow
goes to the label free_eth_finfo, only the allocations starting from
(i-1)th iteration are freed.
Fix that by freeing the loc_array in the bmap allocation error path.
Fixes: d915c299f1da ("cxgb4: add skeleton for ethtool n-tuple filters") Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414170649.89156-1-abdun.nihaal@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid double-copying of string literals. Use a "const char *" for each
string instead of copying from .rodata into stack and then into the skb.
We can go directly from .rodata to the skb.
This also works around a Clang bug (that has since been fixed[1]).
Bluetooth: l2cap: Process valid commands in too long frame
This is required for passing PTS test cases:
- L2CAP/COS/CED/BI-14-C
Multiple Signaling Command in one PDU, Data Truncated, BR/EDR,
Connection Request
- L2CAP/COS/CED/BI-15-C
Multiple Signaling Command in one PDU, Data Truncated, BR/EDR,
Disconnection Request
The test procedure defined in L2CAP.TS.p39 for both tests is:
1. The Lower Tester sends a C-frame to the IUT with PDU Length set
to 8 and Channel ID set to the correct signaling channel for the
logical link. The Information payload contains one L2CAP_ECHO_REQ
packet with Data Length set to 0 with 0 octets of echo data and
one command packet and Data Length set as specified in Table 4.6
and the correct command data.
2. The IUT sends an L2CAP_ECHO_RSP PDU to the Lower Tester.
3. Perform alternative 3A, 3B, 3C, or 3D depending on the IUT’s
response.
Alternative 3A (IUT terminates the link):
3A.1 The IUT terminates the link.
3A.2 The test ends with a Pass verdict.
Alternative 3B (IUT discards the frame):
3B.1 The IUT does not send a reply to the Lower Tester.
Alternative 3C (IUT rejects PDU):
3C.1 The IUT sends an L2CAP_COMMAND_REJECT_RSP PDU to the
Lower Tester.
Alternative 3D (Any other IUT response):
3D.1 The Upper Tester issues a warning and the test ends.
4. The Lower Tester sends a C-frame to the IUT with PDU Length set
to 4 and Channel ID set to the correct signaling channel for the
logical link. The Information payload contains Data Length set to
0 with an L2CAP_ECHO_REQ packet with 0 octets of echo data.
5. The IUT sends an L2CAP_ECHO_RSP PDU to the Lower Tester.
With expected outcome:
In Steps 2 and 5, the IUT responds with an L2CAP_ECHO_RSP.
In Step 3A.1, the IUT terminates the link.
In Step 3B.1, the IUT does not send a reply to the Lower Tester.
In Step 3C.1, the IUT rejects the PDU.
In Step 3D.1, the IUT sends any valid response.
Currently PTS fails with the following logs:
Failed to receive ECHO RESPONSE.
And HCI logs:
> ACL Data RX: Handle 11 flags 0x02 dlen 20
L2CAP: Information Response (0x0b) ident 2 len 12
Type: Fixed channels supported (0x0003)
Result: Success (0x0000)
Channels: 0x000000000000002e
L2CAP Signaling (BR/EDR)
Connectionless reception
AMP Manager Protocol
L2CAP Signaling (LE)
> ACL Data RX: Handle 11 flags 0x02 dlen 13
frame too long
08 01 00 00 08 02 01 00 aa .........
Cc: stable@vger.kernel.org Signed-off-by: Frédéric Danis <frederic.danis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Darrick J. Wong [Tue, 15 Apr 2025 00:33:45 +0000 (17:33 -0700)]
xfs: fix fsmap for internal zoned devices
Filesystems with an internal zoned rt section use xfs_rtblock_t values
that are relative to the start of the data device. When fsmap reports
on internal rt sections, it reports the space used by the data section
as "OWN_FS".
Unfortunately, the logic for resuming a query isn't quite right, so
xfs/273 fails because it stress-tests GETFSMAP with a single-record
buffer. If we enter the "report fake space as OWN_FS" block with a
nonzero key[0].fmr_length, we should add that to key[0].fmr_physical
and recheck if we still need to emit the fake record. We should /not/
just return 0 from the whole function because that prevents all rmap
record iteration.
If we don't enter that block, the resumption is still wrong.
keys[*].fmr_physical is a reflection of what we copied out to userspace
on a previous query, which means that it already accounts for rgstart.
It is not correct to add rtstart_daddr when computing start_rtb or
end_rtb, so stop that.
While we're at it, add a xfs_has_zoned to make it clear that this is a
zoned filesystem thing.
Fixes: e50ec7fac81aa2 ("xfs: enable fsmap reporting for internal RT devices") Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Zhang Xianwei [Sat, 15 Mar 2025 06:32:16 +0000 (14:32 +0800)]
xfs: Fix spelling mistake "drity" -> "dirty"
There is a spelling mistake in fs/xfs/xfs_log.c. Fix it.
Signed-off-by: Zhang Xianwei <zhang.xianwei8@zte.com.cn> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Carlos Maiolino <cem@kernel.org>
ata: libata-sata: Save all fields from sense data descriptor
When filling the taskfile result for a successful NCQ command, we use
the SDB FIS from the FIS Receive Area, see e.g. ahci_qc_ncq_fill_rtf().
However, the SDB FIS only has fields STATUS and ERROR.
For a successful NCQ command that has sense data, we will have a
successful sense data descriptor, in the Sense Data for Successful NCQ
Commands log.
Since we have access to additional taskfile result fields, fill in these
additional fields in qc->result_tf.
This matches how for failing/aborted NCQ commands, we will use e.g.
ahci_qc_fill_rtf() to fill in some fields, but then for the command that
actually caused the NCQ error, we will use ata_eh_read_log_10h(), which
provides additional fields, saving additional fields/overriding the
qc->result_tf that was fetched using ahci_qc_fill_rtf().
Fixes: 18bd7718b5c4 ("scsi: ata: libata: Handle completion of CDL commands using policy 0xD") Signed-off-by: Niklas Cassel <cassel@kernel.org> Reviewed-by: Igor Pylypiv <ipylypiv@google.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Armin Wolf [Mon, 14 Apr 2025 14:04:53 +0000 (16:04 +0200)]
platform/x86: msi-wmi-platform: Workaround a ACPI firmware bug
The ACPI byte code inside the ACPI control method responsible for
handling the WMI method calls uses a global buffer for constructing
the return value, yet the ACPI control method itself is not marked
as "Serialized".
This means that calling WMI methods on this WMI device is not
thread-safe, as concurrent WMI method calls will corrupt the global
buffer.
Fix this by serializing the WMI method calls using a mutex.
Sven Eckelmann [Mon, 14 Apr 2025 18:05:37 +0000 (20:05 +0200)]
batman-adv: Fix double-hold of meshif when getting enabled
It was originally meant to replace the dev_hold with netdev_hold. But this
was missed in batadv_hardif_enable_interface(). As result, there was an
imbalance and a hang when trying to remove the mesh-interface with
(previously) active hard-interfaces:
unregister_netdevice: waiting for batadv0 to become free. Usage count = 3
Fixes: 00b35530811f ("batman-adv: adopt netdev_hold() / netdev_put()") Suggested-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot+ff3aa851d46ab82953a3@syzkaller.appspotmail.com Reported-by: syzbot+4036165fc595a74b09b2@syzkaller.appspotmail.com Reported-by: syzbot+c35d73ce910d86c0026e@syzkaller.appspotmail.com Reported-by: syzbot+48c14f61594bdfadb086@syzkaller.appspotmail.com Reported-by: syzbot+f37372d86207b3bb2941@syzkaller.appspotmail.com Signed-off-by: Sven Eckelmann <sven@narfation.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20250414-double_hold_fix-v5-1-10e056324cde@narfation.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before commit 40867d74c374 ("net: Add l3mdev index to flow struct and
avoid oif reset for port devices") it was possible to use FIB rules to
match on a L3 domain. This was done by having a FIB rule match on iif /
oif being a L3 master device. It worked because prior to the FIB rule
lookup the iif / oif fields in the flow structure were reset to the
index of the L3 master device to which the input / output device was
enslaved to.
The above scheme made it impossible to match on the original input /
output device. Therefore, cited commit stopped overwriting the iif / oif
fields in the flow structure and instead stored the index of the
enslaving L3 master device in a new field ('flowi_l3mdev') in the flow
structure.
While the change enabled new use cases, it broke the original use case
of matching on a L3 domain. Fix this by interpreting the iif / oif
matching on a L3 master device as a match against the L3 domain. In
other words, if the iif / oif in the FIB rule points to a L3 master
device, compare the provided index against 'flowi_l3mdev' rather than
'flowi_{i,o}if'.
Before cited commit, a FIB rule that matched on 'iif vrf1' would only
match incoming traffic from devices enslaved to 'vrf1'. With the
proposed change (i.e., comparing against 'flowi_l3mdev'), the rule would
also match traffic originating from a socket bound to 'vrf1'. Avoid that
by adding a new flow flag ('FLOWI_FLAG_L3MDEV_OIF') that indicates if
the L3 domain was derived from the output interface or the input
interface (when not set) and take this flag into account when evaluating
the FIB rule against the flow structure.
Avoid unnecessary checks in the data path by detecting that a rule
matches on a L3 master device when the rule is installed and marking it
as such.
ip route add table 100 default dev dummy1
ip route add table 200 default dev dummy1
ip route add table 300 default dev dummy1
ip rule add prio 0 oif vrf1 table 100
ip rule add prio 1 iif vrf1 table 200
ip rule add prio 2 table 300
ip route get 192.0.2.1 oif dummy1 fibmatch
ip route get 192.0.2.1 iif dummy1 from 198.51.100.1 fibmatch
Fixes: 40867d74c374 ("net: Add l3mdev index to flow struct and avoid oif reset for port devices") Reported-by: hanhuihui <hanhuihui5@huawei.com> Closes: https://lore.kernel.org/netdev/ec671c4f821a4d63904d0da15d604b75@huawei.com/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: David Ahern <dsahern@kernel.org> Link: https://patch.msgid.link/20250414172022.242991-2-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 14:32:10 +0000 (07:32 -0700)]
eth: bnxt: fix missing ring index trim on error path
Commit under Fixes converted tx_prod to be free running but missed
masking it on the Tx error path. This crashes on error conditions,
for example when DMA mapping fails.
A reference to the device tree node is stored in a private struct, thus
the reference count has to be incremented. Also, decrement the count on
device removal and in the error path.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Michael Walle <mwalle@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250414083942.4015060-1-mwalle@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge tag 'edac_urgent_for_v6.15_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fixes from Borislav Petkov:
"Two fixes to the AMD translation library for the MI300 side of things:
- Use the row[13] bit when calculating the memory row to retire
- Mask the physical row address in order to avoid creating duplicate
error records"
* tag 'edac_urgent_for_v6.15_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
RAS/AMD/FMPM: Get masked address
RAS/AMD/ATL: Include row[13] bit in row retirement
net: ngbe: fix memory leak in ngbe_probe() error path
When ngbe_sw_init() is called, memory is allocated for wx->rss_key
in wx_init_rss_key(). However, in ngbe_probe() function, the subsequent
error paths after ngbe_sw_init() don't free the rss_key. Fix that by
freeing it in error path along with wx->mac_table.
Also change the label to which execution jumps when ngbe_sw_init()
fails, because otherwise, it could lead to a double free for rss_key,
when the mac_table allocation fails in wx_sw_init().
Fixes: 02338c484ab6 ("net: ngbe: Initialize sw info and register netdev") Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com> Reviewed-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com> Link: https://patch.msgid.link/20250412154927.25908-1-abdun.nihaal@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rename the "data" variable inside msi_wmi_platform_read() to avoid
a name collision when the driver adds support for a state container
struct (that is to be called "data" too) in the future.
projects / thirdparty / linux.git / log
