Linus Walleij [Mon, 6 Nov 2017 20:27:34 +0000 (21:27 +0100)]
pinctrl: gemini: Fix GMAC groups
The GMII groups need to be split across GMAC0 and GMAC1 since
GMAC0 is always available but GMAC1 masks GPIO2 lines 0-7
so we might want just one interface out.
Colin Ian King [Tue, 31 Oct 2017 11:20:51 +0000 (11:20 +0000)]
pinctrl: ti-iodelay: remove redundant unused variable dev
The pointer dev is being assigned but is never used, hence it is
redundant and can be removed. Cleans up clang warnings:
drivers/pinctrl/ti/pinctrl-ti-iodelay.c:582:2: warning: Value stored
to 'dev' is never read
drivers/pinctrl/ti/pinctrl-ti-iodelay.c:701:2: warning: Value stored
to 'dev' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Sat, 28 Oct 2017 13:37:17 +0000 (15:37 +0200)]
pinctrl: Add skew-delay pin config and bindings
Some pin controllers (such as the Gemini) can control the
expected clock skew and output delay on certain pins with a
sub-nanosecond granularity. This is typically done by shunting
in a number of double inverters in front of or behind the pin.
Make it possible to configure this with a generic binding.
Cc: devicetree@vger.kernel.org Acked-by: Rob Herring <robh@kernel.org> Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Heiko Stuebner [Sat, 21 Oct 2017 08:53:10 +0000 (10:53 +0200)]
pinctrl: rockchip: Add iomux-route switching support for rk3288
The rk3288 also has one function that can be routed to one of two pins,
the hdmi cec functionality can use either gpio7c0 or gpio7c7.
So add the route switching support for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mika Westerberg [Mon, 23 Oct 2017 12:40:26 +0000 (15:40 +0300)]
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
Intel Cedar Fork PCH is the successor of Intel Denverton PCH but it is
based on the newer GPIO/pinctrl hardware block. Add a new pinctrl/GPIO
driver to support it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mika Westerberg [Mon, 23 Oct 2017 12:40:25 +0000 (15:40 +0300)]
pinctrl: intel: Make offset to interrupt status register configurable
Some GPIO blocks have the interrupt status (GPI_IS) offset different
than it normally is, so make it configurable. If no offset is specified
we use the default.
While there remove two unused constants from the core driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Maxime Ripard [Mon, 9 Oct 2017 20:53:38 +0000 (22:53 +0200)]
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
Old pinctrl drivers will need to disable strict mode for various reasons,
among which:
- Some DT will still have a pinctrl group for each GPIO used, which will
be rejected by pin_request. While we could remove those nodes, we still
have to deal with old DTs.
- Some GPIOs on these boards need to have their pin configuration changed
(for bias or current), and there's no clear migration path
Let's disable the strict mode on those SoCs so that there's no breakage.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Maxime Ripard [Mon, 9 Oct 2017 20:53:37 +0000 (22:53 +0200)]
pinctrl: sunxi: Introduce the strict flag
Our pinctrl device should have had strict set all along. However, it wasn't
the case, and most of our old device trees also have a pinctrl group in
addition to the GPIOs properties, which mean that we can't really turn it
on now.
All our new SoCs don't have that group, so we should still enable that mode
on the newer one though.
In order to enable it by default, add a flag that will allow to disable
that mode that should be set by pinctrl drivers that cannot be migrated.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 20 Oct 2017 13:20:18 +0000 (15:20 +0200)]
Merge tag 'sh-pfc-for-v4.15-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.15 (take two)
- Add Audio, HSCIF, I2C, and INTC-EX pin groups on R-Car H3 ES2.0,
- Add Audio and PWM pin groups on R-Car D3,
- Add support for RZ/A1M and RZ/A1L,
- Add INTC-EX pin groups on R-Car M3-W,
- Add SDHI voltage switching on RZ/G1E,
- Make bias control and IOCTRL support more generic,
- Add suspend/resume support for R-Car Gen3,
- Small fixes and cleanups.
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
During PSCI system suspend, R-Car Gen3 SoCs are powered down, and their
pinctrl register state is lost. Note that as the boot loader skips most
initialization after system resume, pinctrl register state differs from
the state encountered during normal system boot, too.
To fix this, save all GPIO and peripheral function select, module
select, drive strength control, bias, and other I/O control registers
during system suspend, and restore them during system resume.
Note that to avoid overhead on platforms not needing it, the
suspend/resume code has a build time dependency on sleep and PSCI
support, and a runtime dependency on PSCI.
Add a generic way to describe IOCTRL registers (for e.g. SD I/O voltage
and time delay control), like is already done for config, drive, and
bias registers.
This makes the sh-pfc core code aware of these registers, which will
ease introducing suspend/resume support later.
pinctrl: sh-pfc: Drop width parameter of sh_pfc_{read,write}_reg()
On modern Renesas SoCs, all PFC registers are 32-bit, and all callers of
sh_pfc_{read,write}_reg() already operate on 32-bit registers only.
Hence make the 32-bit width implicit, and rename the functions to
sh_pfc_{read,write}() to shorten lines.
All accesses to 8-bit or 16-bit registers are still done using
sh_pfc_{read,write}_raw_reg().
pinctrl: sh-pfc: Remove matching on plain sh-pfc platform device
As of commit 8682b3c522c639f3 ("sh-pfc: Remove platform device
registration"), plain "sh-pfc" platform devices are no longer created.
Hence remove their match entry, and the now obsolete checks for missing
device IDs and driver data.
Linus Walleij [Tue, 17 Oct 2017 09:46:09 +0000 (11:46 +0200)]
blackfin: Fix local <asm/gpio.h> includes
When making the pin control submenu globally visible, all kinds
of oddities appear, in blackfin a few files were #including
<linux/gpio.h> and relying on that to pull in <asm/gpio.h>.
This was not working when pin control but not GPIOLIB was
selected resulting in a breakage in allmodconfig. The code these
files were using was still there and defined in <asm/gpio.h>
just not pulle in from just including <linux/gpio.h>
Simply add the required includes explicitly in the blackfin
kernel core and everything compiles fine.
Delete the use of the incorrect <linux/gpio.h> where possible.
Add stubs to <asm/gpio.h> for the functions called from PM:
these should probably also depend on !PINCTRL but since the
global CONFIG_PM symbol is used to compile PM support,
we need some more intrusive thing here, to be tested by
Blackfin maintainers.
Linus Walleij [Wed, 11 Oct 2017 09:57:15 +0000 (11:57 +0200)]
pinctrl: adi2: Fix Kconfig build problem
The build robot is complaining on Blackfin:
drivers/pinctrl/pinctrl-adi2.c: In function 'port_setup':
>> drivers/pinctrl/pinctrl-adi2.c:221:21: error: dereferencing
pointer to incomplete type 'struct gpio_port_t'
writew(readw(®s->port_fer) & ~BIT(offset),
^~
drivers/pinctrl/pinctrl-adi2.c: In function 'adi_gpio_ack_irq':
>> drivers/pinctrl/pinctrl-adi2.c:266:18: error: dereferencing
pointer to incomplete type 'struct bfin_pint_regs'
if (readl(®s->invert_set) & pintbit)
^~
It seems the driver need to include <asm/gpio.h> and <asm/irq.h>
to compile.
The Blackfin architecture was re-defining the Kconfig
PINCTRL symbol which is not OK, so replaced this with
PINCTRL_BLACKFIN_ADI2 which selects PINCTRL and PINCTRL_ADI2
just like most arches do.
Further, the old GPIO driver symbol GPIO_ADI was possible to
select at the same time as selecting PINCTRL. This was not
working because the arch-local <asm/gpio.h> header contains
an explicit #ifndef PINCTRL clause making compilation break
if you combine them. The same is true for DEBUG_MMRS.
Make sure the ADI2 pinctrl driver is not selected at the same
time as the old GPIO implementation. (This should be converted
to use gpiolib or pincontrol and move to drivers/...) Also make
sure the old GPIO_ADI driver or DEBUG_MMRS is not selected at
the same time as the new PINCTRL implementation, and only make
PINCTRL_ADI2 selectable for the Blackfin families that actually
have it.
This way it is still possible to add e.g. I2C-based pin
control expanders on the Blackfin.
Linus Walleij [Tue, 17 Oct 2017 09:25:44 +0000 (11:25 +0200)]
gpio: Cut old SX150X Kconfig option
The SX150X driver was moved over to pin control a while back.
The GPIO Kconfig symbol creates a circular dependency since
it requires GPIOLIB and the pin control driver selects GPIOLIB
so get rid of the old annoying Kconfig option.
Jerome Brunet [Thu, 12 Oct 2017 12:40:26 +0000 (14:40 +0200)]
pinctrl: meson: rework pinmux ops
This change prepare the introduction of new meson SoC. This new SoC will
share the same gpio/pinconf registers but the pinmux part will be
different. While the format of the data associated with each pinmux group
will change, the way to handle pinmuxing will be similar.
To deal with this new situation, the meson_pmx_struture is kept but the
data associated to it is now generic. This allows to reuse the basic
functions which would otherwise be copy/pasted in each pinmux driver
(such as getting the name a count of groups and functions) Only the
functions actually using this specific data is taken out of the common
code and is handling the SoC pinmuxing
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Jerome Brunet [Thu, 12 Oct 2017 12:40:25 +0000 (14:40 +0200)]
pinctrl: meson: separate soc drivers
When meson pinctrl is enabled, all meson platforms pinctrl drivers are
built in the kernel, with a significant amount of data.
This leads to situation where pinctrl drivers targeting an architecture
are also compiled and shipped on another one (ex: meson8 - ARM - compiled
and shipped on ARM64 builds). This is a waste of memory we can easily
avoid.
This change makes 4 pinctrl drivers (1 per SoC) out the original single
driver, allowing to compile and ship only the ones required.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 11 Oct 2017 10:04:35 +0000 (12:04 +0200)]
pinctrl: Do not depend in GPIOLIB, select it
Instead of depends on GPIOLIB and having to run around in
Kconfig menus looking for why your device is not available,
simply select it from the pin control drivers that need it.
The Kconfig for GPIOLIB is improved, selectable and this
should "just work".
Cc: Phil Reid <preid@electromag.com.au> Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Cc: Peter Rosin <peda@axentia.se> Cc: Andrey Smirnov <andrew.smirnov@gmail.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Takeshi Kihara [Mon, 24 Oct 2016 11:40:09 +0000 (20:40 +0900)]
pinctrl: sh-pfc: r8a7796: Add support for INTC-EX IRQ pins
Most pins on the r8a7796 SoC can be configured in GPIO mode for
interrupt and GPIO functionality, while a couple of them can also
be routed to the INTC-EX hardware block (formerly known as IRQC).
On r8a7795 the INTC-EX hardware handles pins IRQ0 -> IRQ5 and
this patch adds support for them to the PFC driver as "intc_ex_irqN".
[takeshi.kihara.df: Ported from commit bb46f6f3f3bf ("pinctrl: sh-pfc:
r8a7795: Add support for INTC-EX IRQ pins")
to drivers/pinctrl/sh-pfc/pfc-r8a7796.c] Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
pinctrl: qcom: spmi-gpio: Update GPIO EN_CTL when setting pin config
GPIO is expected to be disabled iff PIN_CONFIG_BIAS_HIGH_IMPEDANCE is
configured. Update is_enabled flag in config_set() so that it can
reflect GPIO status correctly. Also modify EN_CTL register based on
is_enabled flag in config_set() to configure the GPIO properly.
Linus Walleij [Sat, 7 Oct 2017 11:12:50 +0000 (13:12 +0200)]
Merge tag 'sh-pfc-for-v4.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.15
- Add SDHI and DRIF pin groups on R-Car H3 ES2.0,
- Add USB3.0 host pin groups on R-Car H3 (ES1.x and ES2.0),
- Add EthernetAVB and USB2.0 host pin groups on R-Car D3.
David Wu [Sat, 30 Sep 2017 12:13:21 +0000 (20:13 +0800)]
pinctrl: rockchip: rk3328: Fix the correct routing config
If the gmac-m1 optimization(bit10) is selected, the gpio function
of gmac pins is not valid. We may use the rmii mode for gmac interface,
the pins such as rx_d2, rx_d3, which the rgmii mode used, but rmii not
used could be taken as gpio function. So gmac_rxd0m1 selects the bit2,
and gmac_rxd0m3 select bit10 is more correct.
David Wu [Sat, 30 Sep 2017 12:13:20 +0000 (20:13 +0800)]
pinctrl: rockchip: Fix the rk3399 gpio0 and gpio1 banks' drv_offset at pmu grf
The offset of gpio0 and gpio1 bank drive strength is 0x8, not 0x4.
But the mux is 0x4, we couldn't use the IOMUX_WIDTH_4BIT flag, so
we give them actual offset.
pin_base was used with the manually set pin offset in meson pinctrl. This
is no longer the case, pin_base is 0 on every meson pinctrl controllers
and should go away.
Offset on meson pinctrl and gpios is something that was carried from the
vendor driver, where there is a weird link between the 2
controllers. Since these 2 controllers are independent, this offset adds
an unnecessary complexity.
This patch remove this manually set offset and rely on pinctrl to figure
out the gpio base offset
Wolfram Sang [Wed, 4 Oct 2017 15:52:52 +0000 (17:52 +0200)]
pinctrl: sh-pfc: r8a7795: Add I2C pin support
Since pinmuxing for I2C is equal on H3 ES1.0 and later versions, copy
the I2C settings from ES1.0. Fixes this error in upstream for
Salvator-XS:
sh-pfc e6060000.pin-controller: function 'i2c2' not supported
sh-pfc e6060000.pin-controller: invalid function i2c2 in map table
i2c-rcar: probe of e6510000.i2c failed with error -22
Now, the bus works the same as with other Salvator boards.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice
namespacing in the other cross-calls like pinctrl_gpio_foo().
Just rename them and all references so we have one namespace
with all cross-calls under pinctrl_gpio_*().
Colin Ian King [Tue, 19 Sep 2017 14:42:18 +0000 (15:42 +0100)]
pinctrl: single: make two arrays static const, reduces object code size
Don't populate the read-only arrays prop2 and prop4 on the stack, instead
make them static const. Makes the object code smaller by over 230 bytes:
Before:
text data bss dec hex filename
28235 5820 192 34247 85c7 drivers/pinctrl/pinctrl-single.o
After:
text data bss dec hex filename
27839 5980 192 34011 84db drivers/pinctrl/pinctrl-single.o
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Colin Ian King [Wed, 13 Sep 2017 16:15:01 +0000 (17:15 +0100)]
pinctrl/amd: make functions amd_gpio_suspend and amd_gpio_resume static
The functions amd_gpio_suspend and amd_gpio_resume are local to the
source and do not need to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'amd_gpio_suspend' was not declared. Should it be static?
symbol 'amd_gpio_resume' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dirk Behme [Wed, 30 Aug 2017 08:05:48 +0000 (10:05 +0200)]
pinctrl: sh-pfc: r8a7795: Re-add DRIF support
DRIF support for r8a7795 was initially added with commit 2d775831988
("pinctrl: sh-pfc: r8a7795: Add DRIF support") and later dropped from
the new pfc-r8a7795.c while re-naming the initial pfc-r8a7795.c to
pfc-r8a7795-es1.c in commit b205914c8f8 ("pinctrl: sh-pfc: r8a7795:
Add support for R-Car H3 ES2.0"). As the DRIF doesn't differ, re-add
it here.
Colin Ian King [Tue, 12 Sep 2017 11:21:24 +0000 (12:21 +0100)]
pinctrl: uniphier: make arrays static, reduces object code size
Don't populate const arrays on the stack, instead make them
static. Makes the object code smaller nearly 1000 bytes. Also
line break wide lines to avoid checkpatch warnings.
Before:
text data bss dec hex filename
13112 1996 0 15108 3b04 pinctrl-uniphier-core.o
After:
text data bss dec hex filename
11642 2476 0 14118 3726 pinctrl-uniphier-core.o
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Merge tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI updates from Richard Weinberger:
"Minor improvements"
* tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs:
UBI: Fix two typos in comments
ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate"
ubi: pr_err() strings should end with newlines
ubi: pr_err() strings should end with newlines
ubi: pr_err() strings should end with newlines
Merge branch 'for-linus-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML updates from Richard Weinberger:
- minor improvements
- fixes for Debian's new gcc defaults (pie enabled by default)
- fixes for XSTATE/XSAVE to make UML work again on modern systems
* 'for-linus-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: return negative in tuntap_open_tramp()
um: remove a stray tab
um: Use relative modversions with LD_SCRIPT_DYN
um: link vmlinux with -no-pie
um: Fix CONFIG_GCOV for modules.
Fix minor typos and grammar in UML start_up help
um: defconfig: Cleanup from old Kconfig options
um: Fix FP register size for XSTATE/XSAVE
1) Fix hotplug deadlock in hv_netvsc, from Stephen Hemminger.
2) Fix double-free in rmnet driver, from Dan Carpenter.
3) INET connection socket layer can double put request sockets, fix
from Eric Dumazet.
4) Don't match collect metadata-mode tunnels if the device is down,
from Haishuang Yan.
5) Do not perform TSO6/GSO on ipv6 packets with extensions headers in
be2net driver, from Suresh Reddy.
6) Fix scaling error in gen_estimator, from Eric Dumazet.
7) Fix 64-bit statistics deadlock in systemport driver, from Florian
Fainelli.
8) Fix use-after-free in sctp_sock_dump, from Xin Long.
9) Reject invalid BPF_END instructions in verifier, from Edward Cree.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
mlxsw: spectrum_router: Only handle IPv4 and IPv6 events
Documentation: link in networking docs
tcp: fix data delivery rate
bpf/verifier: reject BPF_ALU64|BPF_END
sctp: do not mark sk dumped when inet_sctp_diag_fill returns err
sctp: fix an use-after-free issue in sctp_sock_dump
netvsc: increase default receive buffer size
tcp: update skb->skb_mstamp more carefully
net: ipv4: fix l3slave check for index returned in IP_PKTINFO
net: smsc911x: Quieten netif during suspend
net: systemport: Fix 64-bit stats deadlock
net: vrf: avoid gcc-4.6 warning
qed: remove unnecessary call to memset
tg3: clean up redundant initialization of tnapi
tls: make tls_sw_free_resources static
sctp: potential read out of bounds in sctp_ulpevent_type_enabled()
MAINTAINERS: review Renesas DT bindings as well
net_sched: gen_estimator: fix scaling error in bytes/packets samples
nfp: wait for the NSP resource to appear on boot
nfp: wait for board state before talking to the NSP
...
Commit 5620a0d1aac ("firmware: delete in-kernel firmware") removed the
entire firmware directory. Unfortunately it thereby also removed the
support for built-in firmware.
This restores the ability to build firmware directly into the kernel by
pruning the original Makefile to the necessary minimum. The default for
EXTRA_FIRMWARE_DIR is now the standard directory /lib/firmware/.
mlxsw: spectrum_router: Only handle IPv4 and IPv6 events
The driver doesn't support events from address families other than IPv4
and IPv6, so ignore them. Otherwise, we risk queueing a work item before
it's initialized.
This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES
is enabled, as the VRF driver will try to add an l3mdev rule for the
IPMR family.
Fixes: 65e65ec137f4 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Andreas Rammhold <andreas@rammhold.de> Reported-by: Florian Klink <flokli@flokli.de> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 15 Sep 2017 23:47:42 +0000 (16:47 -0700)]
tcp: fix data delivery rate
Now skb->mstamp_skb is updated later, we also need to call
tcp_rate_skb_sent() after the update is done.
Fixes: 8c72c65b426b ("tcp: update skb->skb_mstamp more carefully") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / thirdparty / linux.git / log
