Add a pci_clear_master() stub when CONFIG_PCI is not set so drivers that
support both PCI and platform devices don't need #ifdefs or extra Kconfig
symbols for the PCI parts.
[bhelgaas: commit log] Fixes: 6a479079c072 ("PCI: Add pci_clear_master() as opposite of pci_set_master()") Link: https://lore.kernel.org/r/20230531102744.2354313-1-suijingfeng@loongson.cn Signed-off-by: Sui Jingfeng <suijingfeng@loongson.cn> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch reported:
1. drivers/pci/controller/pci-ftpci100.c:526 faraday_pci_probe() warn:
'clk' from clk_prepare_enable() not released on lines: 442,451,462,478,512,517.
2. drivers/pci/controller/pci-ftpci100.c:526 faraday_pci_probe() warn:
'p->bus_clk' from clk_prepare_enable() not released on lines: 451,462,478,512,517.
The clock resource is obtained by devm_clk_get(), and then
clk_prepare_enable() makes the clock resource ready for use. After that,
clk_disable_unprepare() should be called to release the clock resource
when it is no longer needed. However, while doing some error handling
in faraday_pci_probe(), clk_disable_unprepare() is not called to release
clk and p->bus_clk before returning. These return lines are exactly 442,
451, 462, 478, 512, 517.
Fix this warning by replacing devm_clk_get() with devm_clk_get_enabled(),
which is equivalent to devm_clk_get() + clk_prepare_enable(). And with
devm_clk_get_enabled(), the clock will automatically be disabled,
unprepared and freed when the device is unbound from the bus.
Link: https://lore.kernel.org/r/20230508043641.23807-1-yejunyan@hust.edu.cn Fixes: b3c433efb8a3 ("PCI: faraday: Fix wrong pointer passed to PTR_ERR()") Fixes: 2eeb02b28579 ("PCI: faraday: Add clock handling") Fixes: 783a862563f7 ("PCI: faraday: Use pci_parse_request_of_pci_ranges()") Fixes: d3c68e0a7e34 ("PCI: faraday: Add Faraday Technology FTPCI100 PCI Host Bridge driver") Fixes: f1e8bd21e39e ("PCI: faraday: Convert IRQ masking to raw PCI config accessors") Signed-off-by: Junyan Ye <yejunyan@hust.edu.cn> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a PCIe hotplug slot has an Attention Button, the normal hot-add flow is:
- Slot is empty and slot power is off
- User inserts card in slot and presses Attention Button
- OS blinks Power Indicator for 5 seconds
- After 5 seconds, OS turns on Power Indicator, turns on slot power, and
enumerates the device
Previously, if a user pressed the Attention Button on an *empty* slot,
pciehp logged the following messages and blinked the Power Indicator
until a second button press:
[0.000] pciehp: Button press: will power on in 5 sec
[0.001] # Power Indicator starts blinking
[5.001] # 5 second timeout; slot is empty, so we should cancel the
request to power on and turn off Power Indicator
[7.000] # Power Indicator still blinking
[8.000] # possible card insertion
[9.000] pciehp: Button press: canceling request to power on
The first button press incorrectly left the slot in BLINKINGON_STATE, so
the second was interpreted as a "cancel power on" event regardless of
whether a card was present.
If the slot is empty, turn off the Power Indicator and return from
BLINKINGON_STATE to OFF_STATE after 5 seconds, effectively canceling the
request to power on. Putting the slot in OFF_STATE also means the second
button press will correctly request a slot power on if the slot is
occupied.
This patch adds error checking to tw_probe() to handle initialization
failure. If tw_reset_sequence() function returns a non-zero value, the
function will return -EINVAL to indicate initialization failure.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yuchen Yang <u202114568@hust.edu.cn> Link: https://lore.kernel.org/r/20230505141259.7730-1-u202114568@hust.edu.cn Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Struct pcie_link_state->downstream is a pointer to the pci_dev of function
0. Previously we retained that pointer when removing function 0, and
subsequent ASPM policy changes dereferenced it, resulting in a
use-after-free warning from KASAN, e.g.:
PCIe spec r6.0, sec 7.5.3.7, recommends that software program the same ASPM
Control value in all functions of multi-function devices.
Disable ASPM and free the pcie_link_state when any child function is
removed so we can discard the dangling pcie_link_state->downstream pointer
and maintain the same ASPM Control configuration for all functions.
[bhelgaas: commit log and comment] Debugged-by: Zongquan Qin <qinzongquan@sangfor.com.cn> Suggested-by: Bjorn Helgaas <bhelgaas@google.com> Fixes: b5a0a9b59c81 ("PCI/ASPM: Read and set up L1 substate capabilities") Link: https://lore.kernel.org/r/20230507034057.20970-1-dinghui@sangfor.com.cn Signed-off-by: Ding Hui <dinghui@sangfor.com.cn> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
At this point in the function, nothing has been allocated so we can return
directly. In particular the "qedf->global_queues" have not been allocated
so calling qedf_free_global_queues() will lead to a NULL dereference when
we check if (!gl[i]) and "gl" is NULL.
Fixes: 61d8658b4a43 ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.") Signed-off-by: Jinhong Zhu <jinhongzhu@hust.edu.cn> Link: https://lore.kernel.org/r/20230502140022.2852-1-jinhongzhu@hust.edu.cn Reviewed-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
devm_kasprintf() returns a pointer to dynamically allocated memory.
Pointer could be NULL in case allocation fails. Check pointer validity.
Identified with coccinelle (kmerr.cocci script).
kasprintf() returns a pointer to dynamically allocated memory.
Pointer could be NULL in case allocation fails. Check pointer validity.
Identified with coccinelle (kmerr.cocci script).
Fixes: b745c0794e2f ("clk: keystone: Add sci-clk driver support")
Depends-on: 96488c09b0f4 ("clk: keystone: sci-clk: cut down the clock name length") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20230530093913.1656095-7-claudiu.beznea@microchip.com Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
kasprintf() returns a pointer to dynamically allocated memory.
Pointer could be NULL in case allocation fails. Check pointer validity.
Identified with coccinelle (kmerr.cocci script).
Fixes: 19fbbbbcd3a3 ("Add TI CDCE925 I2C controlled clock synthesizer driver")
Depends-on: e665f029a283 ("clk: Convert to using %pOFn instead of device_node.name") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20230530093913.1656095-3-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function rv740_get_decoded_reference_divider() may return 0 due to
unpredictable reference divider value calculated in
radeon_atom_get_clock_dividers(). This will lead to
division-by-zero error once that value is used as a divider
in calculating 'clk_s'.
While unlikely, this issue should nonetheless be prevented so add a
sanity check for such cases by testing 'decoded_ref' value against 0.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
v2: minor coding style fixes (Alex)
In practice this should actually happen as the vbios should be
properly populated.
Fixes: 66229b200598 ("drm/radeon/kms: add dpm support for rv7xx (v4)") Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix three sources of error involving struct sdma_txreq.num_descs.
When _extend_sdma_tx_descs() extends the descriptor array, it uses the
value of tx->num_descs to determine how many existing entries from the
tx's original, internal descriptor array to copy to the newly allocated
one. As this value was incremented before the call, the copy loop will
access one entry past the internal descriptor array, copying its contents
into the corresponding slot in the new array.
If the call to _extend_sdma_tx_descs() fails, _pad_smda_tx_descs() then
invokes __sdma_tx_clean() which uses the value of tx->num_desc to drive a
loop that unmaps all descriptor entries in use. As this value was
incremented before the call, the unmap loop will invoke sdma_unmap_desc()
on a descriptor entry whose contents consist of whatever random data was
copied into it during (1), leading to cascading further calls into the
kernel and driver using arbitrary data.
_sdma_close_tx() was using tx->num_descs instead of tx->num_descs - 1.
Fix all of the above by:
- Only increment .num_descs after .descp is extended.
- Use .num_descs - 1 instead of .num_descs for last .descp entry.
Fixes: f4d26d81ad7f ("staging/rdma/hfi1: Add coalescing support for SDMA TX descriptors") Link: https://lore.kernel.org/r/167656658879.2223096.10026561343022570690.stgit@awfm-02.cornelisnetworks.com Signed-off-by: Brendan Cunningham <bcunningham@cornelisnetworks.com> Signed-off-by: Patrick Kelsey <pat.kelsey@cornelisnetworks.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix build errors in soc/fsl/qe/usb.c when QUICC_ENGINE is not set.
This happens when PPC_EP88XC is set, which selects CPM1 & CPM.
When CPM is set, USB_FSL_QE can be set without QUICC_ENGINE
being set. When USB_FSL_QE is set, QE_USB deafults to y, which
causes build errors when QUICC_ENGINE is not set. Making
QE_USB depend on QUICC_ENGINE prevents QE_USB from defaulting to y.
Fixes these build errors:
drivers/soc/fsl/qe/usb.o: in function `qe_usb_clock_set':
usb.c:(.text+0x1e): undefined reference to `qe_immr'
powerpc-linux-ld: usb.c:(.text+0x2a): undefined reference to `qe_immr'
powerpc-linux-ld: usb.c:(.text+0xbc): undefined reference to `qe_setbrg'
powerpc-linux-ld: usb.c:(.text+0xca): undefined reference to `cmxgcr_lock'
powerpc-linux-ld: usb.c:(.text+0xce): undefined reference to `cmxgcr_lock'
Fixes: 5e41486c408e ("powerpc/QE: add support for QE USB clocks routing") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/all/202301101500.pillNv6R-lkp@intel.com/ Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Leo Li <leoyang.li@nxp.com> Cc: Masahiro Yamada <masahiroy@kernel.org> Cc: Nicolas Schier <nicolas@fjasle.eu> Cc: Qiang Zhao <qiang.zhao@nxp.com> Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org> Cc: linux-arm-kernel@lists.infradead.org Cc: Kumar Gala <galak@kernel.crashing.org> Acked-by: Nicolas Schier <nicolas@jasle.eu> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using the codec through the generic audio graph card, there are at
least two calls of es8316_set_dai_sysclk(), with the effect of limiting
the allowed sample rates according to the MCLK/LRCK ratios supported by
the codec:
1. During audio card setup, to set the initial MCLK - see
asoc_simple_init_dai().
2. Before opening a stream, to update MCLK, according to the stream
sample rate and the multiplication factor - see
asoc_simple_hw_params().
In some cases the initial MCLK might be set to a frequency that doesn't
match any of the supported ratios, e.g. 12287999 instead of 12288000,
which is only 1 Hz below the supported clock, as that is what the
hardware reports. This creates an empty list of rate constraints, which
is further passed to snd_pcm_hw_constraint_list() via
es8316_pcm_startup(), and causes the following error on the very first
access of the sound card:
$ speaker-test -D hw:Analog,0 -F S16_LE -c 2 -t wav
Broken configuration for playback: no configurations available: Invalid argument
Setting of hwparams failed: Invalid argument
Note that all subsequent retries succeed thanks to the updated MCLK set
at point 2 above, which uses a computed frequency value instead of a
reading from the hardware registers. Normally this would have mitigated
the issue, but es8316_pcm_startup() executes before the 2nd call to
es8316_set_dai_sysclk(), hence it cannot make use of the updated
constraints.
Since es8316_pcm_hw_params() performs anyway a final validation of MCLK
against the stream sample rate and the supported MCLK/LRCK ratios, fix
the issue by ensuring that sysclk_constraints list is only set when at
least one supported sample rate is autodetected by the codec.
According to ES8316 datasheet, the register at address 0x2B, which is
related to the above mixer control, contains by default the value 0xB0.
Considering the corresponding ALC target bits (ALCLVL) are 7:4, the
control is initialized with 11, which is one step above the maximum
value allowed by the driver:
The tests performed using the VU meter feature (--vumeter=TYPE) of
arecord/aplay confirm the specs are correct and there is no measured
gain if the 1011-1111 range would have been mapped to 0 dB:
dB gain | VU meter %
--------+-----------
-6.0 | 30-31
-4.5 | 35-36
-3.0 | 42-43
-1.5 | 50-51
0.0 | 50-51
Increment the max value allowed for ALC Capture Target Volume control,
so that it matches the hardware default. Additionally, update the
related TLV to prevent an artificial extension of the dB gain range.
ep93xx_clocksource_read() is only called from the file it is declared in,
while ep93xx_timer_init() is declared in a header that is not included here.
arch/arm/mach-ep93xx/timer-ep93xx.c:120:13: error: no previous prototype for 'ep93xx_timer_init'
arch/arm/mach-ep93xx/timer-ep93xx.c:63:5: error: no previous prototype for 'ep93xx_clocksource_read'
The previous setting was related to the overall dimension and not to the
active display area.
In the "PHYSICAL SPECIFICATIONS" section, the datasheet shows the
following parameters:
----------------------------------------------------------
| Item | Specifications | unit |
----------------------------------------------------------
| Display area | 98.7 (W) x 57.5 (H) | mm |
----------------------------------------------------------
| Overall dimension | 105.5(W) x 67.2(H) x 4.96(D) | mm |
----------------------------------------------------------
Fixes: 966fea78adf2 ("drm/panel: simple: Add support for Ampire AM-480272H3TMQW-T01H") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
[narmstrong: fixed Fixes commit id length] Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230516085039.3797303-1-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
During destroy_qp, driver sets the qp handle in the existing CQEs
belonging to the QP being destroyed to NULL. As a result, a poll_cq after
destroy_qp can report unnecessary messages. Remove this noise from system
logs.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver") Link: https://lore.kernel.org/r/1684478897-12247-6-git-send-email-selvin.xavier@broadcom.com Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch reports:
drivers/gpu/drm/sun4i/sun4i_tcon.c:805 sun4i_tcon_init_clocks() warn:
'tcon->clk' from clk_prepare_enable() not released on lines: 792,801.
In the function sun4i_tcon_init_clocks(), tcon->clk and tcon->sclk0 are
not disabled in the error handling, which affects the release of
these variable. Although sun4i_tcon_bind(), which calls
sun4i_tcon_init_clocks(), use sun4i_tcon_free_clocks to disable the
variables mentioned, but the error handling branch of
sun4i_tcon_init_clocks() ignores the required disable process.
To fix this issue, use the devm_clk_get_enabled to automatically
balance enable and disabled calls. As original implementation use
sun4i_tcon_free_clocks() to disable clk explicitly, we delete the
related calls and error handling that are no longer needed.
Fixes: 9026e0d122ac ("drm: Add Allwinner A10 Display Engine support") Fixes: b14e945bda8a ("drm/sun4i: tcon: Prepare and enable TCON channel 0 clock at init") Fixes: 8e9240472522 ("drm/sun4i: support TCONs without channel 1") Fixes: 34d698f6e349 ("drm/sun4i: Add has_channel_0 TCON quirk") Signed-off-by: XuDong Liu <m202071377@hust.edu.cn> Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20230430112347.4689-1-m202071377@hust.edu.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no such property in the SPI controller binding documentation.
Also Linux driver doesn't look for it.
This fixes:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: spi@18029200: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
Several calls to ci_dpm_fini() will attempt to free resources that
either have been freed before or haven't been allocated yet. This
may lead to undefined or dangerous behaviour.
For instance, if r600_parse_extended_power_table() fails, it might
call r600_free_extended_power_table() as will ci_dpm_fini() later
during error handling.
Fix this by only freeing pointers to objects previously allocated.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: cc8dbbb4f62a ("drm/radeon: add dpm support for CI dGPUs (v2)") Co-developed-by: Natalia Petrova <n.petrova@fintech.ru> Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported a warning in __local_bh_enable_ip(). [0]
Commit 8d61f926d420 ("netlink: fix potential deadlock in
netlink_set_err()") converted read_lock(&nl_table_lock) to
read_lock_irqsave() in __netlink_diag_dump() to prevent a deadlock.
However, __netlink_diag_dump() calls sock_i_ino() that uses
read_lock_bh() and read_unlock_bh(). If CONFIG_TRACE_IRQFLAGS=y,
read_unlock_bh() finally enables IRQ even though it should stay
disabled until the following read_unlock_irqrestore().
Using read_lock() in sock_i_ino() would trigger a lockdep splat
in another place that was fixed in commit f064af1e500a ("net: fix
a lockdep splat"), so let's add __sock_i_ino() that would be safe
to use under BH disabled.
ipvlan_queue_xmit() should return NET_XMIT_XXX, but
ipvlan_xmit_mode_l2/l3() returns rx_handler_result_t or NET_RX_XXX
in some cases. ipvlan_rcv_frame() will only return RX_HANDLER_CONSUMED
in ipvlan_xmit_mode_l2/l3() because 'local' is true. It's equal to
NET_XMIT_SUCCESS. But dev_forward_skb() can return NET_RX_SUCCESS or
NET_RX_DROP, and returning NET_RX_DROP(NET_XMIT_DROP) will increase
both ipvlan and ipvlan->phy_dev drops counter.
The skb to forward can be treated as xmitted successfully. This patch
makes ipvlan_queue_xmit() return NET_XMIT_SUCCESS for forward skb.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com> Link: https://lore.kernel.org/r/20230626093347.7492-1-cambda@linux.alibaba.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ct_sip_parse_numerical_param() returns only 0 or 1 now.
But process_register_request() and process_register_response() imply
checking for a negative value if parsing of a numerical header parameter
failed.
The invocation in nf_nat_sip() looks correct:
if (ct_sip_parse_numerical_param(...) > 0 &&
...) { ... }
Make the return value of the function ct_sip_parse_numerical_param()
a tristate to fix all the cases
a) return 1 if value is found; *val is set
b) return 0 if value is not found; *val is unchanged
c) return -1 on error; *val is undefined
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
And nothing more is 'pulled' from the packet, depending on the content.
dh->dccph_doff, and/or dh->dccph_x ...)
So dccp_ack_seq() is happily reading stuff past the _dh buffer.
BUG: KASAN: stack-out-of-bounds in nf_conntrack_dccp_packet+0x1134/0x11c0
Read of size 4 at addr ffff000128f66e0c by task syz-executor.2/29371
[..]
Fix this by increasing the stack buffer to also include room for
the extra sequence numbers and all the known dccp packet type headers,
then pull again after the initial validation of the basic header.
While at it, mark packets invalid that lack 48bit sequence bit but
where RFC says the type MUST use them.
Compile tested only.
v2: first skb_header_pointer() now needs to adjust the size to
only pull the generic header. (Eric)
Heads-up: I intend to remove dccp conntrack support later this year.
Fixes: 2bc780499aa3 ("[NETFILTER]: nf_conntrack: add DCCP protocol support") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The `shift` variable which indicates the offset in the string at which
to start matching the pattern is initialized to `bm->patlen - 1`, but it
is not reset when a new block is retrieved. This means the implemen-
tation may start looking at later and later positions in each successive
block and miss occurrences of the pattern at the beginning. E.g.,
consider a HTTP packet held in a non-linear skb, where the HTTP request
line occurs in the second block:
[... 52 bytes of packet headers ...]
GET /bmtest HTTP/1.1\r\nHost: www.example.com\r\n\r\n
and the pattern is "GET /bmtest".
Once the first block comprising the packet headers has been examined,
`shift` will be pointing to somewhere near the end of the block, and so
when the second block is examined the request line at the beginning will
be missed.
Reinitialize the variable for each new block.
Fixes: 8082e4ed0a61 ("[LIB]: Boyer-Moore extension for textsearch infrastructure strike #2") Link: https://bugzilla.netfilter.org/show_bug.cgi?id=1390 Signed-off-by: Jeremy Sowden <jeremy@azazel.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit fixes several use-after-free that caused by function
nfc_llcp_find_local(). For example, one UAF can happen when below buggy
time window occurs.
The buggy address belongs to the object at ffff888105b0e400
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 16 bytes inside of
freed 1024-byte region [ffff888105b0e400, ffff888105b0e800)
Memory state around the buggy address: ffff888105b0e300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888105b0e380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff888105b0e400: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff888105b0e480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888105b0e500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
In summary, this patch solves those use-after-free by
1. Re-implement the nfc_llcp_find_local(). The current version does not
grab the reference when getting the local from the linked list. For
example, the llcp_sock_bind() gets the reference like below:
// llcp_sock_bind()
local = nfc_llcp_find_local(dev); // A
..... \
| raceable
..... /
llcp_sock->local = nfc_llcp_local_get(local); // B
There is an apparent race window that one can drop the reference
and free the local object fetched in (A) before (B) gets the reference.
2. Some callers of the nfc_llcp_find_local() do not grab the reference
at all. For example, the nfc_genl_llc_{{get/set}_params/sdreq} functions.
We add the nfc_llcp_local_put() for them. Moreover, we add the necessary
error handling function to put the reference.
3. Add the nfc_llcp_remove_local() helper. The local object is removed
from the linked list in local_release() when all reference is gone. This
patch removes it when nfc_llcp_unregister_device() is called.
Therefore, every caller of nfc_llcp_find_local() will get a reference
even when the nfc_llcp_unregister_device() is called. This promises no
use-after-free for the local object is ever possible.
Fixes: 52feb444a903 ("NFC: Extend netlink interface for LTO, RW, and MIUX parameters support") Fixes: c7aa12252f51 ("NFC: Take a reference on the LLCP local pointer when creating a socket") Signed-off-by: Lin Ma <linma@zju.edu.cn> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The llcp_sock_connect() error paths were using a mixed way of central
exit (goto) and cleanup
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 6709d4b7bc2e ("net: nfc: Fix use-after-free caused by nfc_llcp_find_local") Signed-off-by: Sasha Levin <sashal@kernel.org>
syzkaller reported use-after-free in __gtp_encap_destroy(). [0]
It shows the same process freed sk and touched it illegally.
Commit e198987e7dd7 ("gtp: fix suspicious RCU usage") added lock_sock()
and release_sock() in __gtp_encap_destroy() to protect sk->sk_user_data,
but release_sock() is called after sock_put() releases the last refcnt.
[0]:
BUG: KASAN: slab-use-after-free in instrument_atomic_read_write include/linux/instrumented.h:96 [inline]
BUG: KASAN: slab-use-after-free in atomic_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:541 [inline]
BUG: KASAN: slab-use-after-free in queued_spin_lock include/asm-generic/qspinlock.h:111 [inline]
BUG: KASAN: slab-use-after-free in do_raw_spin_lock include/linux/spinlock.h:186 [inline]
BUG: KASAN: slab-use-after-free in __raw_spin_lock_bh include/linux/spinlock_api_smp.h:127 [inline]
BUG: KASAN: slab-use-after-free in _raw_spin_lock_bh+0x75/0xe0 kernel/locking/spinlock.c:178
Write of size 4 at addr ffff88800dbef398 by task syz-executor.2/2401
The buggy address belongs to the object at ffff88800dbef300
which belongs to the cache UDPv6 of size 1344
The buggy address is located 152 bytes inside of
freed 1344-byte region [ffff88800dbef300, ffff88800dbef840)
Memory state around the buggy address: ffff88800dbef280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88800dbef300: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88800dbef380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88800dbef400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88800dbef480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
On systems where netdevsim is built-in or loaded before the test
starts, kci_test_ipsec_offload doesn't remove the netdevsim device it
created during the test.
Fixes: e05b2d141fef ("netdevsim: move netdev creation/destruction to dev probe") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Link: https://lore.kernel.org/r/e1cb94f4f82f4eca4a444feec4488a1323396357.1687466906.git.sd@queasysnail.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syz-executor.2/23011 just changed the state of lock: ffffffff8e1a7a58 (nl_table_lock){.+.?}-{2:2}, at: netlink_set_err+0x2e/0x3a0 net/netlink/af_netlink.c:1612
but this lock was taken by another, SOFTIRQ-safe lock in the past:
(&local->queue_stop_reason_lock){..-.}-{2:2}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
Since 'ieee80211_queue_delayed_work()' expects timeout in
jiffies and not milliseconds, 'msecs_to_jiffies()' should
be used in 'ath_restart_work()' and '__ath9k_flush()'.
Fixes: d63ffc45c5d3 ("ath9k: rename tx_complete_work to hw_check_work") Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230613134655.248728-1-dmantipov@yandex.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
The cfg80211_gen_new_ie function merges the IEs using inheritance rules.
Rewrite this function to fix issues around inheritance rules. In
particular, vendor elements do not require any special handling, as they
are either all inherited or overridden by the subprofile.
Also, add fragmentation handling as this may be needed in some cases.
This also changes the function to not require making a copy. The new
version could be optimized a bit by explicitly tracking which IEs have
been handled already rather than looking that up again every time.
Note that a small behavioural change is the removal of the SSID special
handling. This should be fine for the MBSSID element, as the SSID must
be included in the subelement.
In mac80211, it's required that we pull from TXQs by calling
ieee80211_tx_dequeue() only with softirqs disabled. However,
in iwl_mvm_queue_state_change() we're often called with them
enabled, e.g. from flush if anything was flushed, triggering
a mac80211 warning.
Fix that by disabling the softirqs across the TX call.
This filter already exists for excluding IPv6 SNMP stats. Extend its
definition to also exclude IFLA_VF_INFO stats in RTM_GETLINK.
This patch constitutes a partial fix for a netlink attribute nesting
overflow bug in IFLA_VFINFO_LIST. By excluding the stats when the
requester doesn't need them, the truncation of the VF list is avoided.
While it was technically only the stats added in commit c5a9f6f0ab40
("net/core: Add drop counters to VF statistics") breaking the camel's
back, the appreciable size of the stats data should never have been
included without due consideration for the maximum number of VFs
supported by PCI.
Fixes: 3b766cd83232 ("net/core: Add reading VF statistics through the PF netdevice") Fixes: c5a9f6f0ab40 ("net/core: Add drop counters to VF statistics") Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Cc: Edwin Peer <espeer@gmail.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Link: https://lore.kernel.org/r/20230611105108.122586-1-gal@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On EDMA capable hardware, ath9k_txq_list_has_key() can enter infinite
loop if it is called while all txq_fifos have packets that use different
key that the one we are looking for. Fix it by exiting the loop if all
txq_fifos have been checked already.
Because this loop is called under spin_lock_bh() (see ath_txq_lock) it
causes the following rcu stall:
There are no other files referencing this function, apparently
it was left global to avoid an 'unused function' warning when
the only caller is left out. With a 'W=1' build, it causes
a 'missing prototype' warning though:
drivers/memstick/host/r592.c:47:13: error: no previous prototype for 'memstick_debug_get_tpc_name' [-Werror=missing-prototypes]
Annotate the function as 'static __maybe_unused' to avoid both
problems.
Patch series "kexec: enable kexec_crash_size to support two crash kernel
regions".
When crashkernel=X fails to reserve region under 4G, it will fall back to
reserve region above 4G and a region of the default size will also be
reserved under 4G. Unfortunately, /sys/kernel/kexec_crash_size only
supports one crash kernel region now, the user cannot sense the low memory
reserved by reading /sys/kernel/kexec_crash_size. Also, low memory cannot
be freed by writing this file.
For example:
resource_size(crashk_res) = 512M
resource_size(crashk_low_res) = 256M
The result of 'cat /sys/kernel/kexec_crash_size' is 512M, but it should be
768M. When we execute 'echo 0 > /sys/kernel/kexec_crash_size', the size
of crashk_res becomes 0 and resource_size(crashk_low_res) is still 256 MB,
which is incorrect.
Since crashk_res manages the memory with high address and crashk_low_res
manages the memory with low address, crashk_low_res is shrunken only when
all crashk_res is shrunken. And because when there is only one crash
kernel region, crashk_res is always used. Therefore, if all crashk_res is
shrunken and crashk_low_res still exists, swap them.
This patch (of 6):
If the value of parameter 'new_size' is in the semi-open and semi-closed
interval (crashk_res.end - KEXEC_CRASH_MEM_ALIGN + 1, crashk_res.end], the
calculation result of ram_res is:
The operation of insert_resource() fails, and ram_res is not added to
iomem_resource. As a result, the memory of the control block ram_res is
leaked.
In fact, on all architectures, the start address and size of crashk_res
are already aligned by KEXEC_CRASH_MEM_ALIGN. Therefore, we do not need
to round up crashk_res.start again. Instead, we should round up
'new_size' in advance.
Link: https://lkml.kernel.org/r/20230527123439.772-1-thunder.leizhen@huawei.com Link: https://lkml.kernel.org/r/20230527123439.772-2-thunder.leizhen@huawei.com Fixes: 6480e5a09237 ("kdump: add missing RAM resource in crash_shrink_memory()") Fixes: 06a7f711246b ("kexec: premit reduction of the reserved memory size") Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Cong Wang <amwang@redhat.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, in the watchdog_overflow_callback() we first check to see if
the watchdog had been touched and _then_ we handle the workaround for
turbo mode. This order should be reversed.
Specifically, "touching" the hardlockup detector's watchdog should avoid
lockups being detected for one period that should be roughly the same
regardless of whether we're running turbo or not. That means that we
should do the extra accounting for turbo _before_ we look at (and clear)
the global indicating that we've been touched.
NOTE: this fix is made based on code inspection. I am not aware of any
reports where the old code would have generated false positives. That
being said, this order seems more correct and also makes it easier down
the line to share code with the "buddy" hardlockup detector.
Link: https://lkml.kernel.org/r/20230519101840.v5.2.I843b0d1de3e096ba111a179f3adb16d576bef5c7@changeid Fixes: 7edaeb6841df ("kernel/watchdog: Prevent false positives with turbo modes") Signed-off-by: Douglas Anderson <dianders@chromium.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Colin Cross <ccross@android.com> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Guenter Roeck <groeck@chromium.org> Cc: Ian Rogers <irogers@google.com> Cc: Lecopzer Chen <lecopzer.chen@mediatek.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masayoshi Mizuma <msys.mizuma@gmail.com> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Pingfan Liu <kernelfans@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com> Cc: Ricardo Neri <ricardo.neri@intel.com> Cc: Stephane Eranian <eranian@google.com> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Sumit Garg <sumit.garg@linaro.org> Cc: Tzung-Bi Shih <tzungbi@chromium.org> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "watchdog/hardlockup: Add the buddy hardlockup detector", v5.
This patch series adds the "buddy" hardlockup detector. In brief, the
buddy hardlockup detector can detect hardlockups without arch-level
support by having CPUs checkup on a "buddy" CPU periodically.
Given the new design of this patch series, testing all combinations is
fairly difficult. I've attempted to make sure that all combinations of
CONFIG_ options are good, but it wouldn't surprise me if I missed
something. I apologize in advance and I'll do my best to fix any
problems that are found.
This patch (of 18):
The real watchdog_update_hrtimer_threshold() is defined in
kernel/watchdog_hld.c. That file is included if
CONFIG_HARDLOCKUP_DETECTOR_PERF and the function is defined in that file
if CONFIG_HARDLOCKUP_CHECK_TIMESTAMP.
The dummy version of the function in "nmi.h" didn't get that quite right.
While this doesn't appear to be a huge deal, it's nice to make it
consistent.
It doesn't break builds because CHECK_TIMESTAMP is only defined by x86 so
others don't get a double definition, and x86 uses perf lockup detector,
so it gets the out of line version.
Link: https://lkml.kernel.org/r/20230519101840.v5.18.Ia44852044cdcb074f387e80df6b45e892965d4a1@changeid Link: https://lkml.kernel.org/r/20230519101840.v5.1.I8cbb2f4fa740528fcfade4f5439b6cdcdd059251@changeid Fixes: 7edaeb6841df ("kernel/watchdog: Prevent false positives with turbo modes") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Guenter Roeck <groeck@chromium.org> Cc: Ian Rogers <irogers@google.com> Cc: Lecopzer Chen <lecopzer.chen@mediatek.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masayoshi Mizuma <msys.mizuma@gmail.com> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Pingfan Liu <kernelfans@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com> Cc: Ricardo Neri <ricardo.neri@intel.com> Cc: Stephane Eranian <eranian@google.com> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Sumit Garg <sumit.garg@linaro.org> Cc: Tzung-Bi Shih <tzungbi@chromium.org> Cc: Will Deacon <will@kernel.org> Cc: Colin Cross <ccross@android.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It makes no sense to set MMC_PM_KEEP_POWER in shutdown. The flag
indicates to the MMC subsystem to keep the slot powered on during
suspend, but in shutdown the slot should actually be powered off.
Drop this call.
Fixes: 063848c3e155 ("rsi: sdio: Add WOWLAN support for S5 shutdown state") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230527222859.273768-1-marex@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
A bad USB device is able to construct a service connection response
message with target endpoint being ENDPOINT0 which is reserved for
HTC_CTRL_RSVD_SVC and should not be modified to be used for any other
services.
Reject such service connection responses.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Reported-by: syzbot+b68fbebe56d8362907e8@syzkaller.appspotmail.com Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230516150427.79469-1-pchelkin@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Recent work on converting address list to a tree made it obvious
we need an abstraction around writing netdev->dev_addr. Without
such abstraction updating the main device address is invisible
to the core.
Introduce a number of helpers which for now just wrap memcpy()
but in the future can make necessary changes to the address
tree.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 391af06a02e7 ("wifi: wl3501_cs: Fix an error handling path in wl3501_probe()") Signed-off-by: Sasha Levin <sashal@kernel.org>
In file included from drivers/net/wireless/wl3501_cs.c:57:
drivers/net/wireless/wl3501_cs.c:143: warning: Function parameter or member 'reg_domain' not described in 'iw_valid_channel'
drivers/net/wireless/wl3501_cs.c:143: warning: Excess function parameter 'reg_comain' description in 'iw_valid_channel'
drivers/net/wireless/wl3501_cs.c:469: warning: Function parameter or member 'data' not described in 'wl3501_send_pkt'
drivers/net/wireless/wl3501_cs.c:469: warning: Function parameter or member 'len' not described in 'wl3501_send_pkt'
Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Fox Chen <mhchen@golf.ccl.itri.org.tw> Cc: de Melo <acme@conectiva.com.br> Cc: Gustavo Niemeyer <niemeyer@conectiva.com> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201102112410.1049272-25-lee.jones@linaro.org
Stable-dep-of: 391af06a02e7 ("wifi: wl3501_cs: Fix an error handling path in wl3501_probe()") Signed-off-by: Sasha Levin <sashal@kernel.org>
In wl3501_detach(), link->priv is checked for a NULL value before being
passed to free_netdev(). However, it cannot be NULL at this point as it
has already been passed to other functions, so just remove the check.
Addresses-Coverity: CID 710499: Null pointer dereferences (REVERSE_INULL) Signed-off-by: Alex Dewar <alex.dewar90@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200926174558.9436-1-alex.dewar90@gmail.com
Stable-dep-of: 391af06a02e7 ("wifi: wl3501_cs: Fix an error handling path in wl3501_probe()") Signed-off-by: Sasha Levin <sashal@kernel.org>
In file included from drivers/net/wireless/wl3501_cs.c:57:
drivers/net/wireless/wl3501_cs.c:143: warning: Function parameter or member 'reg_domain' not described in 'iw_valid_channel'
drivers/net/wireless/wl3501_cs.c:143: warning: Function parameter or member 'channel' not described in 'iw_valid_channel'
drivers/net/wireless/wl3501_cs.c:162: warning: Function parameter or member 'reg_domain' not described in 'iw_default_channel'
drivers/net/wireless/wl3501_cs.c:248: warning: Function parameter or member 'this' not described in 'wl3501_set_to_wla'
drivers/net/wireless/wl3501_cs.c:270: warning: Function parameter or member 'this' not described in 'wl3501_get_from_wla'
drivers/net/wireless/wl3501_cs.c:467: warning: Function parameter or member 'this' not described in 'wl3501_send_pkt'
drivers/net/wireless/wl3501_cs.c:467: warning: Function parameter or member 'data' not described in 'wl3501_send_pkt'
drivers/net/wireless/wl3501_cs.c:467: warning: Function parameter or member 'len' not described in 'wl3501_send_pkt'
drivers/net/wireless/wl3501_cs.c:729: warning: Function parameter or member 'this' not described in 'wl3501_block_interrupt'
drivers/net/wireless/wl3501_cs.c:746: warning: Function parameter or member 'this' not described in 'wl3501_unblock_interrupt'
drivers/net/wireless/wl3501_cs.c:1124: warning: Function parameter or member 'irq' not described in 'wl3501_interrupt'
drivers/net/wireless/wl3501_cs.c:1124: warning: Function parameter or member 'dev_id' not described in 'wl3501_interrupt'
drivers/net/wireless/wl3501_cs.c:1257: warning: Function parameter or member 'dev' not described in 'wl3501_reset'
drivers/net/wireless/wl3501_cs.c:1420: warning: Function parameter or member 'link' not described in 'wl3501_detach'
Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Fox Chen <mhchen@golf.ccl.itri.org.tw> Cc: de Melo <acme@conectiva.com.br> Cc: Gustavo Niemeyer <niemeyer@conectiva.com> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200826093401.1458456-21-lee.jones@linaro.org
Stable-dep-of: 391af06a02e7 ("wifi: wl3501_cs: Fix an error handling path in wl3501_probe()") Signed-off-by: Sasha Levin <sashal@kernel.org>
regulator: Failed to create debugfs directory
...
regulator-dummy: Failed to create debugfs directory
As per the comments for debugfs_create_dir(), errors returned by this
function should be expected, and ignored:
* If debugfs is not enabled in the kernel, the value -%ENODEV will be
* returned.
*
* NOTE: it's expected that most callers should _ignore_ the errors returned
* by this function. Other debugfs functions handle the fact that the "dentry"
* passed to them could be an error and they don't crash in that case.
* Drivers should generally work fine even if debugfs fails to init anyway.
Adhere to the debugfs spirit, and streamline all operations by:
1. Demoting the importance of the printed error messages to debug
level, like is already done in create_regulator(),
2. Further ignoring any returned errors, as by design, all debugfs
functions are no-ops when passed an error pointer.
In case of failure, debugfs_create_dir() does not return NULL, but an
error pointer. Most incorrect error checks were fixed, but the one in
create_regulator() was forgotten.
If sock->service_name is NULL, the local variable
service_name_tlv_length will not be assigned by nfc_llcp_build_tlv(),
later leading to using value frmo the stack. Smatch warning:
net/nfc/llcp_commands.c:442 nfc_llcp_send_connect() error: uninitialized symbol 'service_name_tlv_length'.
Fixes: de9e5aeb4f40 ("NFC: llcp: Fix usage of llcp_add_tlv()") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Several functions receive pointers to u8, char or sk_buff but do not
modify the contents so make them const. This allows doing the same for
local variables and in total makes the code a little bit safer.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 0d9b41daa590 ("nfc: llcp: fix possible use of uninitialized variable in nfc_llcp_send_connect()") Signed-off-by: Sasha Levin <sashal@kernel.org>
The CS_TOGGLE bit when set is supposed to instruct FW to
toggle CS line between words. The driver with intent of
disabling this behaviour has been unsetting BIT(0). This has
not caused any trouble so far because the original BIT(1)
is untouched and BIT(0) likely wasn't being used.
Correct this to prevent a potential future bug.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Reviewed-by: Douglas Anderson <dianders@chromium.org Link: https://lore.kernel.org/r/1682412128-1913-1-git-send-email-quic_vnivarth@quicinc.com Signed-off-by: Mark Brown <broonie@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
For the reasons also described in commit b383e8abed41 ("wifi: ath9k: avoid
uninit memory read in ath9k_htc_rx_msg()"), ath9k_htc_rx_msg() should
validate pkt_len before accessing the SKB.
For example, the obtained SKB may have been badly constructed with
pkt_len = 8. In this case, the SKB can only contain a valid htc_frame_hdr
but after being processed in ath9k_htc_rx_msg() and passed to
ath9k_wmi_ctrl_rx() endpoint RX handler, it is expected to have a WMI
command header which should be located inside its data payload.
Implement sanity checking inside ath9k_wmi_ctrl_rx(). Otherwise, uninit
memory can be referenced.
Tested on Qualcomm Atheros Communications AR9271 802.11n .
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Reported-and-tested-by: syzbot+f2cb6e0ffdb961921e4d@syzkaller.appspotmail.com Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230424183348.111355-1-pchelkin@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix ath9k_hw_verify_hang()/ar9003_hw_detect_mac_hang() register offset
calculation (do not overflow the shift for the second register/queues
above five, use the register layout described in the comments above
ath9k_hw_verify_hang() instead).
checker_stack_use_t32strd() and kprobe_handler() can be made static since
they are not used from other files, while coverage_start_registers()
and __kprobes_test_case() are used from assembler code, and just need
a declaration to avoid a warning with the global definition.
arch/arm/probes/kprobes/checkers-common.c:43:18: error: no previous prototype for 'checker_stack_use_t32strd'
arch/arm/probes/kprobes/core.c:236:16: error: no previous prototype for 'kprobe_handler'
arch/arm/probes/kprobes/test-core.c:723:10: error: no previous prototype for 'coverage_start_registers'
arch/arm/probes/kprobes/test-core.c:918:14: error: no previous prototype for '__kprobes_test_case_start'
arch/arm/probes/kprobes/test-core.c:952:14: error: no previous prototype for '__kprobes_test_case_end_16'
arch/arm/probes/kprobes/test-core.c:967:14: error: no previous prototype for '__kprobes_test_case_end_32'
Fixes: 6624cf651f1a ("ARM: kprobes: collects stack consumption for store instructions") Fixes: 454f3e132d05 ("ARM/kprobes: Remove jprobe arm implementation") Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 3382388d7148 ("intel_rapl: abstract RAPL common code"),
accessing to IOSF_MBI interface is done in the RAPL common code.
Thus it is the CONFIG_INTEL_RAPL_CORE that has dependency of
CONFIG_IOSF_MBI, while CONFIG_INTEL_RAPL_MSR does not.
This problem was not exposed previously because all the previous RAPL
common code users, aka, the RAPL MSR and MMIO I/F drivers, have
CONFIG_IOSF_MBI selected.
Fix the CONFIG_IOSF_MBI dependency in RAPL code. This also fixes a build
time failure when the RAPL TPMI I/F driver is introduced without
selecting CONFIG_IOSF_MBI.
x86_64-linux-ld: vmlinux.o: in function `set_floor_freq_atom':
intel_rapl_common.c:(.text+0x2dac9b8): undefined reference to `iosf_mbi_write'
x86_64-linux-ld: intel_rapl_common.c:(.text+0x2daca66): undefined reference to `iosf_mbi_read'
Reference to iosf_mbi.h is also removed from the RAPL MSR I/F driver.
Fixes: 3382388d7148 ("intel_rapl: abstract RAPL common code") Reported-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/all/20230601213246.3271412-1-arnd@kernel.org Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, while calculating residency and latency values, right
operands may overflow if resulting values are big enough.
To prevent this, albeit unlikely case, play it safe and convert
right operands to left ones' type s64.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 30f604283e05 ("PM / Domains: Allow domain power states to be read from DT") Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch reports:
drivers/clocksource/timer-cadence-ttc.c:529 ttc_timer_probe()
warn: 'timer_baseaddr' from of_iomap() not released on lines: 498,508,516.
timer_baseaddr may have the problem of not being released after use,
I replaced it with the devm_of_iomap() function and added the clk_put()
function to cleanup the "clk_ce" and "clk_cs".
Fixes: e932900a3279 ("arm: zynq: Use standard timer binding") Fixes: 70504f311d4b ("clocksource/drivers/cadence_ttc: Convert init function to return error") Signed-off-by: Feng Mingxi <m202271825@hust.edu.cn> Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn> Acked-by: Michal Simek <michal.simek@amd.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20230425065611.702917-1-m202271825@hust.edu.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently TTC driver is TIMER_OF_DECLARE type driver. Because of
that, TTC driver may be initialized before other clock drivers. If
TTC driver is dependent on that clock driver then initialization of
TTC driver will failed.
So use TTC driver as platform driver instead of using
TIMER_OF_DECLARE.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/1573122988-18399-1-git-send-email-rajan.vaja@xilinx.com
Stable-dep-of: 8b5bf64c89c7 ("clocksource/drivers/cadence-ttc: Fix memory leak in ttc_timer_probe") Signed-off-by: Sasha Levin <sashal@kernel.org>
The trace output for the HRTIMER_MODE_.*_HARD modes is seen as a number
since these modes are not decoded. The author was not aware of the fancy
decoding function which makes the life easier.
Extend decode_hrtimer_mode() with the additional HRTIMER_MODE_.*_HARD
modes.
Fixes: ae6683d815895 ("hrtimer: Introduce HARD expiry mode") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com> Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org> Link: https://lore.kernel.org/r/20230418143854.8vHWQKLM@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
The initialization function for the J-Core AIC aic_irq_of_init() is
currently missing the call to irq_alloc_descs() which allocates and
initializes all the IRQ descriptors. Add missing function call and
return the error code from irq_alloc_descs() in case the allocation
fails.
Fixes: 981b58f66cfc ("irqchip/jcore-aic: Add J-Core AIC driver") Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Tested-by: Rob Landley <rob@landley.net> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230510163343.43090-1-glaubitz@physik.fu-berlin.de Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing a disk with replacement, the replacement will be used to
replace rdev. During this process, there is a brief window in which both
rdev and replacement are read as NULL in raid10_write_request(). This
will result in io not being submitted but it should be.
Fix it by reading replacement first and rdev later, meanwhile, use smp_mb()
to prevent memory reordering.
Fixes: 475b0321a4df ("md/raid10: writes should get directed to replacement as well as original.") Signed-off-by: Li Nan <linan122@huawei.com> Reviewed-by: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20230602091839.743798-3-linan666@huaweicloud.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two check of 'mreplace' in raid10_sync_request(). In the first
check, 'need_replace' will be set and 'mreplace' will be used later if
no-Faulty 'mreplace' exists, In the second check, 'mreplace' will be
set to NULL if it is Faulty, but 'need_replace' will not be changed
accordingly. null-ptr-deref occurs if Faulty is set between two check.
Fix it by merging two checks into one. And replace 'need_replace' with
'mreplace' because their values are always the same.
Fixes: ee37d7314a32 ("md/raid10: Fix raid10 replace hang when new added disk faulty") Signed-off-by: Li Nan <linan122@huawei.com> Reviewed-by: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20230527072218.2365857-2-linan666@huaweicloud.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no input check when echo md/safe_mode_delay in safe_delay_store().
And msec might also overflow when HZ < 1000 in safe_delay_show(), Fix it by
checking overflow in safe_delay_store() and use unsigned long conversion in
safe_delay_show().
If we write a large number to md/bitmap_set_bits, md_bitmap_checkpage()
will return -EINVAL because 'page >= bitmap->pages', but the return value
was not checked immediately in md_bitmap_get_counter() in order to set
*blocks value and slab-out-of-bounds occurs.
Move check of 'page >= bitmap->pages' to md_bitmap_get_counter() and
return directly if true.
Fixes: ef4256733506 ("md/bitmap: optimise scanning of empty bitmaps.") Signed-off-by: Li Nan <linan122@huawei.com> Reviewed-by: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20230515134808.3936750-2-linan666@huaweicloud.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When writing a task id to the "tasks" file in an rdtgroup,
rdtgroup_tasks_write() treats the pid as a number in the current pid
namespace. But when reading the "tasks" file, rdtgroup_tasks_show() shows
the list of global pids from the init namespace, which is confusing and
incorrect.
To be more robust, let the "tasks" file only show pids in the current pid
namespace.
rdtgroup_tasks_assigned() and show_rdt_tasks() loop over threads testing
for a CTRL/MON group match by closid/rmid with the provided rdtgrp.
Further down the file are helpers to do this, move these further up and
make use of them here.
These helpers additionally check for alloc/mon capable. This is harmless
as rdtgroup_mkdir() tests these capable flags before allowing the config
directories to be created.
Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Reinette Chatre <reinette.chatre@intel.com> Link: https://lkml.kernel.org/r/20200708163929.2783-7-james.morse@arm.com
Stable-dep-of: 2997d94b5dd0 ("x86/resctrl: Only show tasks' pid in current pid namespace") Signed-off-by: Sasha Levin <sashal@kernel.org>
While bringing hardware up we should perform a full reset including the
switch bit (BGMAC_BCMA_IOCTL_SW_RESET aka SICF_SWRST). It's what
specification says and what reference driver does.
This seems to be critical for the BCM5358. Without this hardware doesn't
get initialized properly and doesn't seem to transmit or receive any
packets.
Originally bgmac was calling bgmac_chip_reset() before setting
"has_robosw" property which resulted in expected behaviour. That has
changed as a side effect of adding platform device support which
regressed BCM5358 support.
gtags considers any file outside of its current working directory
"outside the source tree" and refuses to index it. For O= kernel builds,
or when "make" is invoked from a directory other then the kernel source
tree, gtags ignores the entire kernel source and generates an empty
index.
Force-set gtags current working directory to the kernel source tree.
Due to commit 9da0763bdd82 ("kbuild: Use relative path when building in
a subdir of the source tree"), if the kernel build is done in a
sub-directory of the kernel source tree, the kernel Makefile will set
the kernel's $srctree to ".." for shorter compile-time and run-time
warnings. Consequently, the list of files to be indexed will be in the
"../*" form, rendering all such paths invalid once gtags switches to the
kernel source tree as its current working directory.
If gtags indexing is requested and the build directory is not the kernel
source tree, index all files in absolute-path form.
Note, indexing in absolute-path form will not affect the generated
index, as paths in gtags indices are always relative to the gtags "root
directory" anyway (as evidenced by "gtags --dump").
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de> Cc: <stable@vger.kernel.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just in case the caller passes in 0 for both slow&fast timeouts, make
sure we initialise the stack value returned. Add an assert so that we
don't make the mistake of passing 0 timeouts for the wait.
drivers/gpu/drm/i915/intel_uncore.c:2011 __intel_wait_for_register_fw() error: uninitialized symbol 'reg_value'.
Code which interacts with timestamps needs to use the ktime_t type
returned by functions like ktime_get. The int type does not offer
enough space to store these values, and attempting to use it is a
recipe for problems. In this particular case, overflows would occur
when calculating/storing timestamps leading to incorrect values being
reported to userspace. In some cases these bad timestamps cause input
handling in userspace to appear hung.
A use-after-free bug may occur if init_imstt invokes framebuffer_release
and free the info ptr. The caller, imsttfb_probe didn't notice that and
still keep the ptr as private data in pdev.
If we remove the driver which will call imsttfb_remove to make cleanup,
UAF happens.
Fix it by return error code if bad case happens in init_imstt.
We should check if ioremap() were to somehow fail in imsttfb_probe() and
handle the unwinding of the resources allocated here properly.
Ideally if anyone cares about this driver (it's for a PowerMac era PCI
display card), they wouldn't even be using fbdev anymore. Or the devm_*
apis could be used, but that's just extra work for diminishing
returns...
Monitoring idletask::thread_info::flags in mwait_play_dead() has been an
obvious choice as all what is needed is a cache line which is not written
by other CPUs.
But there is a use case where a "dead" CPU needs to be brought out of
MWAIT: kexec().
This is required as kexec() can overwrite text, pagetables, stacks and the
monitored cacheline of the original kernel. The latter causes MWAIT to
resume execution which obviously causes havoc on the kexec kernel which
results usually in triple faults.
Use a dedicated per CPU storage to prepare for that.
projects / thirdparty / kernel / stable.git / log
