Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
SDM845 has ETMv4.2 and can use the existing etm4x driver.
But the current etm driver checks only for ETMv4.0 and
errors out for other etm4x versions. This patch adds this
missing support to enable SoC's with ETMv4x to use same
driver by checking only the ETM architecture major version
number.
Without this change, we get below error during etm probe:
/ # dmesg | grep etm
[ 6.660093] coresight-etm4x: probe of 7040000.etm failed with error -22
[ 6.666902] coresight-etm4x: probe of 7140000.etm failed with error -22
[ 6.673708] coresight-etm4x: probe of 7240000.etm failed with error -22
[ 6.680511] coresight-etm4x: probe of 7340000.etm failed with error -22
[ 6.687313] coresight-etm4x: probe of 7440000.etm failed with error -22
[ 6.694113] coresight-etm4x: probe of 7540000.etm failed with error -22
[ 6.700914] coresight-etm4x: probe of 7640000.etm failed with error -22
[ 6.707717] coresight-etm4x: probe of 7740000.etm failed with error -22
When building with -Wsometimes-uninitialized, Clang warns:
arch/powerpc/xmon/ppc-dis.c:157:7: warning: variable 'opcode' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (cpu_has_feature(CPU_FTRS_POWER9))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/xmon/ppc-dis.c:167:7: note: uninitialized use occurs here
if (opcode == NULL)
^~~~~~
arch/powerpc/xmon/ppc-dis.c:157:3: note: remove the 'if' if its
condition is always true
if (cpu_has_feature(CPU_FTRS_POWER9))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/xmon/ppc-dis.c:132:38: note: initialize the variable
'opcode' to silence this warning
const struct powerpc_opcode *opcode;
^
= NULL
1 warning generated.
This warning seems to make no sense on the surface because opcode is set
to NULL right below this statement. However, there is a comma instead of
semicolon to end the dialect assignment, meaning that the opcode
assignment only happens in the if statement. Properly terminate that
line so that Clang no longer warns.
We had a test-report where, under memory pressure, adding LUNs to the
systems would fail (the tests add LUNs strictly in sequence):
[ 5525.853432] scsi 0:0:1:1088045124: Direct-Access IBM 2107900 .148 PQ: 0 ANSI: 5
[ 5525.853826] scsi 0:0:1:1088045124: alua: supports implicit TPGS
[ 5525.853830] scsi 0:0:1:1088045124: alua: device naa.6005076303ffd32700000000000044da port group 0 rel port 43
[ 5525.853931] sd 0:0:1:1088045124: Attached scsi generic sg10 type 0
[ 5525.854075] sd 0:0:1:1088045124: [sdk] Disabling DIF Type 1 protection
[ 5525.855495] sd 0:0:1:1088045124: [sdk] 2097152 512-byte logical blocks: (1.07 GB/1.00 GiB)
[ 5525.855606] sd 0:0:1:1088045124: [sdk] Write Protect is off
[ 5525.855609] sd 0:0:1:1088045124: [sdk] Mode Sense: ed 00 00 08
[ 5525.855795] sd 0:0:1:1088045124: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5525.857838] sdk: sdk1
[ 5525.859468] sd 0:0:1:1088045124: [sdk] Attached SCSI disk
[ 5525.865073] sd 0:0:1:1088045124: alua: transition timeout set to 60 seconds
[ 5525.865078] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015070] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015213] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.587439] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
[ 5526.588562] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
Looking at the code of scsi_alloc_sdev(), and all the calling contexts,
there seems to be no reason to use GFP_ATMOIC here. All the different
call-contexts use a mutex at some point, and nothing in between that
requires no sleeping, as far as I could see. Additionally, the code that
later allocates the block queue for the device (scsi_mq_alloc_queue())
already uses GFP_KERNEL.
There are similar allocations in two other functions:
scsi_probe_and_add_lun(), and scsi_add_lun(),; that can also be done with
GFP_KERNEL.
Here is the contexts for the three functions so far:
So replace all these, and give them a bit of a better chance to succeed,
with more chances of reclaim.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.
This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.
Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.
When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The cavium/zip implementation of the deflate compression algorithm is
incorrectly being registered under the generic driver name, which
prevents the generic implementation from being registered with the
crypto API when CONFIG_CRYPTO_DEV_CAVIUM_ZIP=y. Similarly the lzs
algorithm (which does not currently have a generic implementation...)
is incorrectly being registered as lzs-generic.
Fix the naming collision by adding a suffix "-cavium" to the
cra_driver_name of the cavium/zip algorithms.
Fixes: 640035a2dc55 ("crypto: zip - Add ThunderX ZIP driver core") Cc: Mahipal Challa <mahipalreddy2006@gmail.com> Cc: Jan Glauber <jglauber@cavium.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
e = f(...);
... when != of_node_put(e)
when != x = e
when != e = x
when any
if (<+...of_device_is_available(e)...+>) {
... when != of_node_put(e)
(
return e;
|
+ of_node_put(e);
return ...;
)
}
// </smpl>
Fixes: 5343e674f32fb ("crypto4xx: integrate ppc4xx-rng into crypto4xx") Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
ies1 or ies2 might be null when code inside
_wil_cfg80211_merge_extra_ies access them.
Add explicit check for null and make sure ies1/ies2 are not
accessed in such a case.
spos might be null and be accessed inside
_wil_cfg80211_merge_extra_ies.
Add explicit check for null in the while condition statement
and make sure spos is not accessed in such a case.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is incorrect to call pcie_pme_suspend() from pcie_pme_remove() for two
reasons.
First, pcie_pme_suspend() calls synchronize_irq(), which will wait for the
native hotplug interrupt handler as well as for the PME one, because they
share one IRQ (as per the spec). That may deadlock if hotplug is signaled
while pcie_pme_remove() is running and the latter calls
pci_lock_rescan_remove() before the former.
Second, if pcie_pme_suspend() figures out that wakeup needs to be enabled
for the port, it will return without disabling the interrupt as expected by
pcie_pme_remove() which was overlooked by commit c7b5a4e6e8fb ("PCI / PM:
Fix native PME handling during system suspend/resume").
To fix that, rework pcie_pme_remove() to disable the PME interrupt, clear
its status and prevent the PME worker function from re-enabling it before
calling free_irq() on it, which should be sufficient.
Fixes: c7b5a4e6e8fb ("PCI / PM: Fix native PME handling during system suspend/resume") Link: https://lore.kernel.org/linux-pci/c7697e7c-e1af-13e4-8491-0a3996e6ab5d@huawei.com Reported-by: Dongdong Liu <liudongdong3@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bhelgaas: add URL and deadlock details from Dongdong] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
guard_bio_eod() can truncate a segment in bio to allow it to do IO on
odd last sectors of a device.
It already checks if the IO starts past EOD, but it does not consider
the possibility of an IO request starting within device boundaries can
contain more than one segment past EOD.
In such cases, truncated_bytes can be bigger than PAGE_SIZE, and will
underflow bvec->bv_len.
Fix this by checking if truncated_bytes is lower than PAGE_SIZE.
This situation has been found on filesystems such as isofs and vfat,
which doesn't check the device size before mount, if the device is
smaller than the filesystem itself, a readahead on such filesystem,
which spans EOD, can trigger this situation, leading a call to
zero_user() with a wrong size possibly corrupting memory.
I didn't see any crash, or didn't let the system run long enough to
check if memory corruption will be hit somewhere, but adding
instrumentation to guard_bio_end() to check truncated_bytes size, was
enough to see the error.
In jbd2_journal_commit_transaction(), if we are in abort mode,
we may flush the buffer without setting descriptor block checksum
by goto start_journal_io. Then fs is mounted,
jbd2_descriptor_block_csum_verify() failed.
Invoking dm_get_device() twice on the same device path with different
modes is dangerous. Because in that case, upgrade_mode() will alloc a
new 'dm_dev' and free the old one, which may be referenced by a previous
caller. Dereferencing the dangling pointer will trigger kernel NULL
pointer dereference.
The following two cases can reproduce this issue. Actually, they are
invalid setups that must be disallowed, e.g.:
1. Creating a thin-pool with read_only mode, and the same device as
both metadata and data.
Signed-off-by: Jason Cai (Xiang Feng) <jason.cai@linux.alibaba.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When compiling with -Wformat, clang emits the following warnings:
fs/cifs/smb1ops.c:312:20: warning: format specifies type 'unsigned
short' but the argument has type 'unsigned int' [-Wformat]
tgt_total_cnt, total_in_tgt);
^~~~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:289:4: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->flags, ref->server_type);
^~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:289:16: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->flags, ref->server_type);
^~~~~~~~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:291:4: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->ref_flag, ref->path_consumed);
^~~~~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:291:19: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->ref_flag, ref->path_consumed);
^~~~~~~~~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct ones for ints and unsigned
ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378 Signed-off-by: Louis Taylor <louis@kragniz.eu> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
(Taken from https://bugzilla.kernel.org/show_bug.cgi?id=200647)
'get_unused_fd_flags' in kthread cause kernel crash. It works fine on
4.1, but causes crash after get 64 fds. It also cause crash on
ubuntu1404/1604/1804, centos7.5, and the crash messages are almost the
same.
This issue exists since CentOS 7.5 3.10.0-862 and CentOS 7.4
(3.10.0-693.21.1 ) is ok. Root cause: the item 'resize_wait' is not
initialized before being used.
Reported-by: Richard Zhang <zhang.zijian@h3c.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the process of creating a node, it will cause NULL pointer
dereference in kernel if o2cb_ctl failed in the interval (mkdir,
o2cb_set_node_attribute(node_num)] in function o2cb_add_node.
The node num is initialized to 0 in function o2nm_node_group_make_item,
o2nm_node_group_drop_item will mistake the node number 0 for a valid
node number when we delete the node before the node number is set
correctly. If the local node number of the current host happens to be
0, cluster->cl_local_node will be set to O2NM_INVALID_NODE_NUM while
o2hb_thread still running. The panic stack is generated as follows:
Kmemleak does not track the array cache (alc->ac) but the alien cache
(alc) instead, so let it track the latter by lifting kmemleak_no_scan()
out of init_arraycache().
There is another place that calls init_arraycache(), but
alloc_kmem_cache_cpus() uses the percpu allocation where will never be
considered as a leak.
As it's difficult to report where exactly the uninit value resides in
the mempolicy object, we have to guess a bit. mm/mempolicy.c:353
contains this part of mpol_rebind_policy():
if (!mpol_store_user_nodemask(pol) &&
nodes_equal(pol->w.cpuset_mems_allowed, *newmask))
"mpol_store_user_nodemask(pol)" is testing pol->flags, which I couldn't
ever see being uninitialized after leaving mpol_new(). So I'll guess
it's actually about accessing pol->w.cpuset_mems_allowed on line 354,
but still part of statement starting on line 353.
For w.cpuset_mems_allowed to be not initialized, and the nodes_equal()
reachable for a mempolicy where mpol_set_nodemask() is called in
do_mbind(), it seems the only possibility is a MPOL_PREFERRED policy
with empty set of nodes, i.e. MPOL_LOCAL equivalent, with MPOL_F_LOCAL
flag. Let's exclude such policies from the nodes_equal() check. Note
the uninit access should be benign anyway, as rebinding this kind of
policy is always a no-op. Therefore no actual need for stable
inclusion.
Link: http://lkml.kernel.org/r/a71997c3-e8ae-a787-d5ce-3db05768b27c@suse.cz Link: http://lkml.kernel.org/r/73da3e9c-cc84-509e-17d9-0c434bb9967d@suse.cz Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: syzbot+b19c2dc2c990ea657a71@syzkaller.appspotmail.com Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: David Rientjes <rientjes@google.com> Cc: Yisheng Xie <xieyisheng1@huawei.com> Cc: zhong jiang <zhongjiang@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After offlining a memory block, kmemleak scan will trigger a crash, as
it encounters a page ext address that has already been freed during
memory offlining. At the beginning in alloc_page_ext(), it calls
kmemleak_alloc(), but it does not call kmemleak_free() in
free_page_ext().
Kmemleak is supposed to work with the memblock_{alloc,free} pair and it
ignores the memblock_reserve() as a memblock_alloc() implementation
detail. It is, however, tolerant to memblock_free() being called on
a sub-range or just a different range from a previous memblock_alloc().
So the original patch looks fine to me. FWIW:
Link: http://lkml.kernel.org/r/20190227144631.16708-1-peng.fan@nxp.com Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pm8xxx_get_channel() implementation is unclear, and causes gcc to
suddenly generate odd warnings. The trigger for the warning (at least
for me) was the entirely unrelated commit 79a4e91d1bb2 ("device.h: Add
__cold to dev_<level> logging functions"), which apparently changes gcc
code generation in the caller function enough to cause this:
drivers/iio/adc/qcom-pm8xxx-xoadc.c: In function ‘pm8xxx_xoadc_probe’:
drivers/iio/adc/qcom-pm8xxx-xoadc.c:633:8: warning: ‘ch’ may be used uninitialized in this function [-Wmaybe-uninitialized]
ret = pm8xxx_read_channel_rsv(adc, ch, AMUX_RSV4,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
&read_nomux_rsv4, true);
~~~~~~~~~~~~~~~~~~~~~~~
drivers/iio/adc/qcom-pm8xxx-xoadc.c:426:27: note: ‘ch’ was declared here
struct pm8xxx_chan_info *ch;
^~
because gcc for some reason then isn't able to see that the termination
condition for the "for( )" loop in that function is also the condition
for returning NULL.
So it's not _actually_ uninitialized, but the function is admittedly
just unnecessarily oddly written.
Simplify and clarify the function, making gcc also see that it always
returns a valid initialized value.
Cc: Joe Perches <joe@perches.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Andy Gross <andy.gross@linaro.org> Cc: David Brown <david.brown@linaro.org> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the PHY comes down, we currently do not set the negotiated linkrate:
root@(none)$ pwd
/sys/class/sas_phy/phy-0:0
root@(none)$ more enable
1
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$
This patch fixes the driver code to set it properly when the PHY comes
down.
If the PHY had been enabled, then set unknown; otherwise, flag as disabled.
The logical place to set the negotiated linkrate for this scenario is PHY
down routine, which is called from the PHY down ISR.
However, it is not possible to know if the PHY comes down due to PHY
disable or loss of link, as sas_phy.enabled member is not set until after
the transport disable routine is complete, which races with the PHY down
ISR.
As an imperfect solution, use sas_phy_data.enable as the flag to know if
the PHY is down due to disable. It's imperfect, as sas_phy_data is internal
to libsas.
I can't see another way without adding a new field to hisi_sas_phy and
managing it, or changing SCSI SAS transport.
Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The enic driver relies on the CONFIG_CPUMASK_OFFSTACK feature to
dynamically allocate a struct member, but this is normally intended for
local variables.
Building with clang, I get a warning for a few locations that check the
address of the cpumask_var_t:
drivers/net/ethernet/cisco/enic/enic_main.c:122:22: error: address of array 'enic->msix[i].affinity_mask' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
As far as I can tell, the code is still correct, as the truth value of
the pointer is what we need in this configuration. To get rid of
the warning, use cpumask_available() instead of checking the
pointer directly.
Fixes: 322cf7e3a4e8 ("enic: assign affinity hint to interrupts") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
/proc/sys/fs/file-max will overflow and be set to 0. That quickly
crashes the system.
This commit sets the max and min value for file-max. The max value is
set to long int. Any higher value cannot currently be used as the
percpu counters are long ints and not unsigned integers.
Note that the file-max value is ultimately parsed via
__do_proc_doulongvec_minmax(). This function does not report error when
min or max are exceeded. Which means if a value largen that long int is
written userspace will not receive an error instead the old value will be
kept. There is an argument to be made that this should be changed and
__do_proc_doulongvec_minmax() should return an error when a dedicated min
or max value are exceeded. However this has the potential to break
userspace so let's defer this to an RFC patch.
Link: http://lkml.kernel.org/r/20190107222700.15954-3-christian@brauner.io Signed-off-by: Christian Brauner <christian@brauner.io> Acked-by: Kees Cook <keescook@chromium.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Waiman Long <longman@redhat.com>
[christian@brauner.io: v4] Link: http://lkml.kernel.org/r/20190210203943.8227-3-christian@brauner.io Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The percpu member of this structure is declared as:
struct ... ** __percpu member;
So its type is:
__percpu pointer to pointer to struct ...
But looking at how it's used, its type should be:
pointer to __percpu pointer to struct ...
and it should thus be declared as:
struct ... * __percpu *member;
So fix the placement of '__percpu' in the definition of this
structures.
This silents a few Sparse's warnings like:
warning: incorrect type in initializer (different address spaces)
expected void const [noderef] <asn:3> *__vpp_verify
got struct sched_domain **
Link: http://lkml.kernel.org/r/20190118144902.79065-1-luc.vanoostenryck@gmail.com Fixes: 017c59c042d01 ("relay: Use per CPU constructs for the relay channel buffer pointers") Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Cc: Jens Axboe <axboe@suse.de> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony notes that the GPIO module does not idle when level interrupts are
in use, as the wakeup appears to get stuck.
After extensive investigation, it appears that the wakeup will only be
cleared if the interrupt status register is cleared while the interrupt
is enabled. However, we are currently clearing it with the interrupt
disabled for level-based interrupts.
It is acknowledged that this observed behaviour conflicts with a
statement in the TRM:
CAUTION
After servicing the interrupt, the status bit in the interrupt status
register (GPIOi.GPIO_IRQSTATUS_0 or GPIOi.GPIO_IRQSTATUS_1) must be
reset and the interrupt line released (by setting the corresponding
bit of the interrupt status register to 1) before enabling an
interrupt for the GPIO channel in the interrupt-enable register
(GPIOi.GPIO_IRQSTATUS_SET_0 or GPIOi.GPIO_IRQSTATUS_SET_1) to prevent
the occurrence of unexpected interrupts when enabling an interrupt
for the GPIO channel.
However, this does not appear to be a practical problem.
Further, as reported by Grygorii Strashko <grygorii.strashko@ti.com>,
the TI Android kernel tree has an earlier similar patch as "GPIO: OMAP:
Fix the sequence to clear the IRQ status" saying:
if the status is cleared after disabling the IRQ then sWAKEUP will not
be cleared and gates the module transition
When we unmask the level interrupt after the interrupt has been handled,
enable the interrupt and only then clear the interrupt. If the interrupt
is still pending, the hardware will re-assert the interrupt status.
Should the caution note in the TRM prove to be a problem, we could
use a clear-enable-clear sequence instead.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Keerthy <j-keerthy@ti.com> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: updated comments based on an earlier TI patch] Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As reported back in 2016-11 [1], the "ftdump" kdb command triggers a
BUG for "sleeping function called from invalid context".
kdb's "ftdump" command wants to call ring_buffer_read_prepare() in
atomic context. A very simple solution for this is to add allocation
flags to ring_buffer_read_prepare() so kdb can call it without
triggering the allocation error. This patch does that.
Note that in the original email thread about this, it was suggested
that perhaps the solution for kdb was to either preallocate the buffer
ahead of time or create our own iterator. I'm hoping that this
alternative of adding allocation flags to ring_buffer_read_prepare()
can be considered since it means I don't need to duplicate more of the
core trace code into "trace_kdb.c" (for either creating my own
iterator or re-preparing a ring allocator whose memory was already
allocated).
NOTE: another option for kdb is to actually figure out how to make it
reuse the existing ftrace_dump() function and totally eliminate the
duplication. This sounds very appealing and actually works (the "sr
z" command can be seen to properly dump the ftrace buffer). The
downside here is that ftrace_dump() fully consumes the trace buffer.
Unless that is changed I'd rather not use it because it means "ftdump
| grep xyz" won't be very useful to search the ftrace buffer since it
will throw away the whole trace on the first grep. A future patch to
dump only the last few lines of the buffer will also be hard to
implement.
Link: http://lkml.kernel.org/r/20190308193205.213659-1-dianders@chromium.org Reported-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
sometimes, dead lock when make system call SYS_getdents64 with fsync() is
called by another process.
monkey running on android9.0
1. task 9785 held sbi->cp_rwsem and waiting lock_page()
2. task 10349 held mm_sem and waiting sbi->cp_rwsem
3. task 9709 held lock_page() and waiting mm_sem
Since f2fs_readdir is protected by inode.i_rwsem, there should not be
any updates in inode page, we're safe to lookup dents in inode page
without its lock held, so taking off the lock to improve concurrency
of readdir and avoid potential deadlock.
Reported-by: Jiqun Li <jiqun.li@unisoc.com> Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It believe it is a bad idea to hardcode a specific compiler prefix
that may or may not be installed on a user's system. It is annoying
when testing features that should not require compilers at all.
For example, mrproper, headers_install, etc. should work without
any compiler.
They look like follows on my machine.
$ make ARCH=h8300 mrproper
./scripts/gcc-version.sh: line 26: h8300-unknown-linux-gcc: command not found
./scripts/gcc-version.sh: line 27: h8300-unknown-linux-gcc: command not found
make: h8300-unknown-linux-gcc: Command not found
make: h8300-unknown-linux-gcc: Command not found
[ a bunch of the same error messages continue ]
$ make ARCH=h8300 headers_install
./scripts/gcc-version.sh: line 26: h8300-unknown-linux-gcc: command not found
./scripts/gcc-version.sh: line 27: h8300-unknown-linux-gcc: command not found
make: h8300-unknown-linux-gcc: Command not found
HOSTCC scripts/basic/fixdep
make: h8300-unknown-linux-gcc: Command not found
WRAP arch/h8300/include/generated/uapi/asm/kvm_para.h
[ snip ]
The solution is to delete this line, or to use cc-cross-prefix like
some architectures do. I chose the latter as a moderate fixup.
I added an alternative 'h8300-linux-' because it is available at:
Notice how we don't call locks_lock_file_wait() which does the
generic VFS lock/unlock/wait work on the inode if rc != 0.
If we are closing the handle, the SMB server is supposed to remove any
locks associated with it. Similarly, cifs.ko frees and wakes up any
lock and lock waiter when closing the file:
cifs_close()
cifsFileInfo_put(file->private_data)
/*
* Delete any outstanding lock records. We'll lose them when the file
* is closed anyway.
*/
down_write(&cifsi->lock_sem);
list_for_each_entry_safe(li, tmp, &cifs_file->llist->locks, llist) {
list_del(&li->llist);
cifs_del_lock_waiters(li);
kfree(li);
}
list_del(&cifs_file->llist->llist);
kfree(cifs_file->llist);
up_write(&cifsi->lock_sem);
So we can safely ignore unlocking failures in cifs_lock() if they
happen with the FL_CLOSE flag hint set as both the server and the
client take care of it during the actual closing.
This is not a proper fix for the unlocking failure but it's safe and
it seems to prevent the lock leakages and crashes the customer
experiences.
Signed-off-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: NeilBrown <neil@brown.name> Signed-off-by: Steve French <stfrench@microsoft.com> Acked-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When MPOL_MF_STRICT was specified and an existing page was already on a
node that does not follow the policy, mbind() should return -EIO. But
commit 6f4576e3687b ("mempolicy: apply page table walker on
queue_pages_range()") broke the rule.
And commit c8633798497c ("mm: mempolicy: mbind and migrate_pages support
thp migration") didn't return the correct value for THP mbind() too.
If MPOL_MF_STRICT is set, ignore vma_migratable() to make sure it
reaches queue_pages_to_pte_range() or queue_pages_pmd() to check if an
existing page was already on a node that does not follow the policy.
And, non-migratable vma may be used, return -EIO too if MPOL_MF_MOVE or
MPOL_MF_MOVE_ALL was specified.
Tested with https://github.com/metan-ucw/ltp/blob/master/testcases/kernel/syscalls/mbind/mbind02.c
[akpm@linux-foundation.org: tweak code comment] Link: http://lkml.kernel.org/r/1553020556-38583-1-git-send-email-yang.shi@linux.alibaba.com Fixes: 6f4576e3687b ("mempolicy: apply page table walker on queue_pages_range()") Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com> Signed-off-by: Oscar Salvador <osalvador@suse.de> Reported-by: Cyril Hrubis <chrubis@suse.cz> Suggested-by: Kirill A. Shutemov <kirill@shutemov.name> Acked-by: Rafael Aquini <aquini@redhat.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Acked-by: David Rientjes <rientjes@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In half-duplex operation, RX should be started after TX completes.
If DMA is used, there is a case when the DMA transfer completes but the
TX FIFO is not emptied, so the RX cannot be restarted just yet.
Use a boolean variable to store this state and rearm TX interrupt mask
to be signaled again that the transfer finished. In interrupt transmit
handler this variable is used to start RX. A warning message is generated
if RX is activated before TX fifo is cleared.
Fixes: b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable
RX after TX is done") Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com> Acked-by: Richard Genoud <richard.genoud@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
m = 1UL << (BITS_PER_LONG - 2);
while (m > x)
m >>= 2;
Which is a linear search for the highest even bit smaller or equal to @x
We can implement this using a binary search using __fls() (or better when
its hardware implemented).
m = 1UL << (__fls(x) & ~1UL);
Especially for small values of @x; which are the more common arguments
when doing a CDF on idle times; the linear search is near to worst case,
while the binary search of __fls() is a constant 6 (or 5 on 32bit)
branches.
Averages computed over all values <128k using a LFSR to generate order.
Cold numbers have a LFSR based branch trace buffer 'confuser' ran between
each int_sqrt() invocation.
Link: http://lkml.kernel.org/r/20171020164644.936577234@infradead.org Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Suggested-by: Joe Perches <joe@perches.com> Acked-by: Will Deacon <will.deacon@arm.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Anshul Garg <aksgarg1989@gmail.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: David Miller <davem@davemloft.net> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Matthew Wilcox <mawilcox@microsoft.com> Cc: Michael Davidson <md@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Joe Perches <joe@perches.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we are releasing the indirect buffer where we are done with
it in ext4_ind_remove_space(), so we can see the brelse() and
BUFFER_TRACE() everywhere. It seems fragile and hard to read, and we
may probably forget to release the buffer some day. This patch cleans
up the code by putting of the code which releases the buffers to the
end of the function.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Jari Ruusu <jari.ruusu@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FAR_EL1 is UNKNOWN for all debug exceptions other than those caused by
taking a hardware watchpoint. Unfortunately, if a debug handler returns
a non-zero value, then we will propagate the UNKNOWN FAR value to
userspace via the si_addr field of the SIGTRAP siginfo_t.
Instead, let's set si_addr to take on the PC of the faulting instruction,
which we have available in the current pt_regs.
Cc: <stable@vger.kernel.org> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we get an interrupt for a channel program, it is not
necessarily the final interrupt; for example, the issuing
guest may request an intermediate interrupt by specifying
the program-controlled-interrupt flag on a ccw.
We must not switch the state to idle if the interrupt is not
yet final; even more importantly, we must not free the translated
channel program if the interrupt is not yet final, or the host
can crash during cp rewind.
The CPUID flag ARCH_CAPABILITIES is unconditioinally exposed to host
userspace for all x86 hosts, i.e. KVM advertises ARCH_CAPABILITIES
regardless of hardware support under the pretense that KVM fully
emulates MSR_IA32_ARCH_CAPABILITIES. Unfortunately, only VMX hosts
handle accesses to MSR_IA32_ARCH_CAPABILITIES (despite KVM_GET_MSRS
also reporting MSR_IA32_ARCH_CAPABILITIES for all hosts).
Move the MSR_IA32_ARCH_CAPABILITIES handling to common x86 code so
that it's emulated on AMD hosts.
Fixes: 1eaafe91a0df4 ("kvm: x86: IA32_ARCH_CAPABILITIES is always supported") Cc: stable@vger.kernel.org Reported-by: Xiaoyao Li <xiaoyao.li@linux.intel.com> Cc: Jim Mattson <jmattson@google.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KVM's API requires thats ioctls must be issued from the same process
that created the VM. In other words, userspace can play games with a
VM's file descriptors, e.g. fork(), SCM_RIGHTS, etc..., but only the
creator can do anything useful. Explicitly reject device ioctls that
are issued by a process other than the VM's creator, and update KVM's
API documentation to extend its requirements to device ioctls.
Fixes: 852b6d57dc7f ("kvm: add device control API") Cc: <stable@vger.kernel.org> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SMT disable 'nosmt' command line argument is not working properly when
CONFIG_HOTPLUG_CPU is disabled. The teardown of the sibling CPUs which are
required to be brought up due to the MCE issues, cannot work. The CPUs are
then kept in a half dead state.
As the 'nosmt' functionality has become popular due to the speculative
hardware vulnerabilities, the half torn down state is not a proper solution
to the problem.
Enforce CONFIG_HOTPLUG_CPU=y when SMP is enabled so the full operation is
possible.
Reported-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Konrad Wilk <konrad.wilk@oracle.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Mukesh Ojha <mojha@codeaurora.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Rik van Riel <riel@surriel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Micheal Kelley <michael.h.kelley@microsoft.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190326163811.598166056@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tianyu reported a crash in a CPU hotplug teardown callback when booting a
kernel which has CONFIG_HOTPLUG_CPU disabled with the 'nosmt' boot
parameter.
It turns out that the SMP=y CONFIG_HOTPLUG_CPU=n case has been broken
forever in case that a bringup callback fails. Unfortunately this issue was
not recognized when the CPU hotplug code was reworked, so the shortcoming
just stayed in place.
When a bringup callback fails, the CPU hotplug code rolls back the
operation and takes the CPU offline.
The 'nosmt' command line argument uses a bringup failure to abort the
bringup of SMT sibling CPUs. This partial bringup is required due to the
MCE misdesign on Intel CPUs.
With CONFIG_HOTPLUG_CPU=y the rollback works perfectly fine, but
CONFIG_HOTPLUG_CPU=n lacks essential mechanisms to exercise the low level
teardown of a CPU including the synchronizations in various facilities like
RCU, NOHZ and others.
As a consequence the teardown callbacks which must be executed on the
outgoing CPU within stop machine with interrupts disabled are executed on
the control CPU in interrupt enabled and preemptible context causing the
kernel to crash and burn. The pre state machine code has a different
failure mode which is more subtle and resulting in a less obvious use after
free crash because the control side frees resources which are still in use
by the undead CPU.
But this is not a x86 only problem. Any architecture which supports the
SMP=y HOTPLUG_CPU=n combination suffers from the same issue. It's just less
likely to be triggered because in 99.99999% of the cases all bringup
callbacks succeed.
The easy solution of making HOTPLUG_CPU mandatory for SMP is not working on
all architectures as the following architectures have either no hotplug
support at all or not all subarchitectures support it:
Crashing the kernel in such a situation is not an acceptable state
either.
Implement a minimal rollback variant by limiting the teardown to the point
where all regular teardown callbacks have been invoked and leave the CPU in
the 'dead' idle state. This has the following consequences:
- the CPU is brought down to the point where the stop_machine takedown
would happen.
- the CPU stays there forever and is idle
- The CPU is cleared in the CPU active mask, but not in the CPU online
mask which is a legit state.
- Interrupts are not forced away from the CPU
- All facilities which only look at online mask would still see it, but
that is the case during normal hotplug/unplug operations as well. It's
just a (way) longer time frame.
This will expose issues, which haven't been exposed before or only seldom,
because now the normally transient state of being non active but online is
a permanent state. In testing this exposed already an issue vs. work queues
where the vmstat code schedules work on the almost dead CPU which ends up
in an unbound workqueue and triggers 'preemtible context' warnings. This is
not a problem of this change, it merily exposes an already existing issue.
Still this is better than crashing fully without a chance to debug it.
This is mainly thought as workaround for those architectures which do not
support HOTPLUG_CPU. All others should enforce HOTPLUG_CPU for SMP.
Fixes: 2e1a3483ce74 ("cpu/hotplug: Split out the state walk into functions") Reported-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Konrad Wilk <konrad.wilk@oracle.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Mukesh Ojha <mojha@codeaurora.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Rik van Riel <riel@surriel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Micheal Kelley <michael.h.kelley@microsoft.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190326163811.503390616@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A TSC packet can slip past MTC packets so that the timestamp appears to
go backwards. One estimate is that can be up to about 40 CPU cycles,
which is certainly less than 0x1000 TSC ticks, but accept slippage an
order of magnitude more to be on the safe side.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org Fixes: 79b58424b821c ("perf tools: Add Intel PT support for decoding MTC packets") Link: http://lkml.kernel.org/r/20190325135135.18348-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our MIPS 1004Kc SoCs were seeing random userspace crashes with SIGILL
and SIGSEGV that could not be traced back to a userspace code bug. They
had all the magic signs of an I/D cache coherency issue.
Now recently we noticed that the /proc/sys/vm/compact_memory interface
was quite efficient at provoking this class of userspace crashes.
Studying the code in mm/migrate.c there is a distinction made between
migrating a page that is mapped at the instant of migration and one that
is not mapped. Our problem turned out to be the non-mapped pages.
For the non-mapped page the code performs a copy of the page content and
all relevant meta-data of the page without doing the required D-cache
maintenance. This leaves dirty data in the D-cache of the CPU and on
the 1004K cores this data is not visible to the I-cache. A subsequent
page-fault that triggers a mapping of the page will happily serve the
process with potentially stale code.
What about ARM then, this bug should have seen greater exposure? Well
ARM became immune to this flaw back in 2010, see commit c01778001a4f
("ARM: 6379/1: Assume new page cache pages have dirty D-cache").
My proposed fix moves the D-cache maintenance inside move_to_new_page to
make it common for both cases.
Link: http://lkml.kernel.org/r/20190315083502.11849-1-larper@axis.com Fixes: 97ee0524614 ("flush cache before installing new page at migraton") Signed-off-by: Lars Persson <larper@axis.com> Reviewed-by: Paul Burton <paul.burton@mips.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the kernel is compiled with preemption enabled, the URB completion
handler can run in parallel with the work responsible for waking up the
tty layer. If the URB handler sets the EVENT_TTY_WAKEUP bit during the
call to tty_port_tty_wakeup() to signal that there is room for additional
input, it will be cleared at the end of this call. As a result, TX traffic
on the upper layer will be blocked.
This can be seen with a kernel configured with CONFIG_PREEMPT, and a fast
modem connected with PPP running over a USB CDC-ACM port.
Use test_and_clear_bit() instead, which ensures that each wakeup requested
by the URB completion code will trigger a call to tty_port_tty_wakeup().
A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.
Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.
Add U1 and U2 to the possible link states when checking for finished
port resume.
When plugging BUFFALO LUA4-U3-AGT USB3.0 to Gigabit Ethernet LAN
Adapter, warning messages filled up dmesg.
[ 101.098287] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[ 101.117463] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[ 101.136513] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
Adding the XHCI_TRUST_TX_LENGTH quirk resolves the issue.
There are cases where multiple device tree nodes point to the
same phy node by means of the "phys" property, but we should
only consider those nodes that are marked as available rather
than just any node.
Fixes: 98bfb3946695 ("usb: of: add an api to get dr_mode by the phy node") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In f_hidg_write() the write_spinlock is acquired before calling
usb_ep_queue() which causes a deadlock when dummy_hcd is being used.
This is because dummy_queue() callbacks into f_hidg_req_complete() which
tries to acquire the same spinlock. This is (part of) the backtrace when
the deadlock occurs:
0xffffffffc06b1410 in f_hidg_req_complete
0xffffffffc06a590a in usb_gadget_giveback_request
0xffffffffc06cfff2 in dummy_queue
0xffffffffc06a4b96 in usb_ep_queue
0xffffffffc06b1eb6 in f_hidg_write
0xffffffff8127730b in __vfs_write
0xffffffff812774d1 in vfs_write
0xffffffff81277725 in SYSC_write
Fix this by releasing the write_spinlock before calling usb_ep_queue()
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com> Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: stable@vger.kernel.org # 4.11+ Fixes: 749494b6bdbb ("usb: gadget: f_hid: fix: Move IN request allocation to set_alt()") Signed-off-by: Radoslav Gerganov <rgerganov@vmware.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While only the first PHY supports mode switching, the remaining PHYs
work in USB host mode. They should support set_mode with mode=USB_HOST
instead of failing. This is especially needed now that the USB core does
set_mode for all USB ports, which was added in commit b97a31348379 ("usb:
core: comply to PHY framework").
Make set_mode with mode=USB_HOST a no-op instead of failing for the
non-OTG USB PHYs.
Fixes: 6ba43c291961 ("phy-sun4i-usb: Add support for phy_set_mode") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code test wrong value so it does not verify if the written
data is correctly read back. Fix it.
Also make it return -EPERM if read value does not match written bit,
just like it done for adnp_gpio_direction_output().
If drm_gem_handle_create() fails in vgem_gem_create(), then the
drm_vgem_gem_object is freed twice: once when the reference is dropped
by drm_gem_object_put_unlocked(), and again by __vgem_gem_destroy().
This was hit by syzkaller using fault injection.
Fix it by skipping the second free.
Reported-by: syzbot+e73f2fb5ed5a5df36d33@syzkaller.appspotmail.com Fixes: af33a9190d02 ("drm/vgem: Enable dmabuf import interfaces") Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Laura Abbott <labbott@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190226214451.195123-1-ebiggers@kernel.org Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new dir entry can be created in get_subdir and its 'header->parent' is
set to NULL. Only after insert_header success, it will be set to 'dir',
otherwise 'header->parent' is set to NULL and drop_sysctl_table is called.
However in err handling path of get_subdir, drop_sysctl_table also be
called on 'new->header' regardless its value of parent pointer. Then
put_links is called, which triggers NULL-ptr deref when access member of
header->parent.
In fact we have multiple error paths which call drop_sysctl_table() there,
upon failure on insert_links() we also call drop_sysctl_table().And even
in the successful case on __register_sysctl_table() we still always call
drop_sysctl_table().This patch fix it.
Link: http://lkml.kernel.org/r/20190314085527.13244-1-yuehaibing@huawei.com Fixes: 0e47c99d7fe25 ("sysctl: Replace root_list with links between sysctl_table_sets") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reported-by: Hulk Robot <hulkci@huawei.com> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: <stable@vger.kernel.org> [3.4+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Quectel EM12 is a Cat. 12 LTE modem. It behaves in the exactly the
same way as the EP06 (including the dynamic configuration behavior), so
the same checks on reserved interfaces, etc. are needed.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4
of which are serial ports. The fifth is a network interface supported
by the qmi-wwan driver. Furthermore, the serial ports do not support
modem control signals. Add driver_info flags to reflect this.
The write_parport_reg_nonblock() helper takes a reference to the struct
mos_parport, but failed to release it in a couple of error paths after
allocation failures, leading to a memory leak.
Johan said that move the kref_get() and mos_parport assignment to the
end of urbtrack initialisation is a better way, so move it. and
mos_parport do not used until urbtrack initialisation.
Signed-off-by: Lin Yi <teroincn@163.com> Fixes: b69578df7e98 ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Cc: stable <stable@vger.kernel.org> # 2.6.35 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lorenz Messtechnik has a device that is controlled by the cp210x driver,
so add the device id to the driver. The device id was provided by
Silicon-Labs for the devices from this vendor.
We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted
(if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer,
re-enable the SCSCR_TIE bit, which was done at sci_start_tx().
This is unnecessary processing, wasting CPU operation if the data transmission length is large.
And further, transmit end, FIFO empty bits disabling have also been performed in the step above.
`ni_cdio_cmdtest()` validates Comedi asynchronous commands for the DIO
subdevice (subdevice 2) of supported National Instruments M-series
cards. It is called when handling the `COMEDI_CMD` and `COMEDI_CMDTEST`
ioctls for this subdevice. There are two causes for a possible
divide-by-zero error when validating that the `stop_arg` member of the
passed-in command is not too large.
The first cause for the divide-by-zero is that calls to
`comedi_bytes_per_scan()` are only valid once the command has been
copied to `s->async->cmd`, but that copy is only done for the
`COMEDI_CMD` ioctl. For the `COMEDI_CMDTEST` ioctl, it will use
whatever was left there by the previous `COMEDI_CMD` ioctl, if any.
(This is very likely, as it is usual for the application to use
`COMEDI_CMDTEST` before `COMEDI_CMD`.) If there has been no previous,
valid `COMEDI_CMD` for this subdevice, then `comedi_bytes_per_scan()`
will return 0, so the subsequent division in `ni_cdio_cmdtest()` of
`s->async->prealloc_bufsz / comedi_bytes_per_scan(s)` will be a
divide-by-zero error. To fix this error, call a new function
`comedi_bytes_per_scan_cmd(s, cmd)`, based on the existing
`comedi_bytes_per_scan(s)` but using a specified `struct comedi_cmd` for
its calculations. (Also refactor `comedi_bytes_per_scan()` to call the
new function.)
Once the first cause for the divide-by-zero has been fixed, the second
cause is that `comedi_bytes_per_scan_cmd()` can legitimately return 0 if
the `scan_end_arg` member of the `struct comedi_cmd` being tested is 0.
Fix it by only performing the division (and validating that `stop_arg`
is no more than the maximum value) if `comedi_bytes_per_scan_cmd()`
returns a non-zero value.
The problem was reported on the COMEDI mailing list here:
https://groups.google.com/forum/#!topic/comedi_list/4t9WlHzMhKM
Reported-by: Ivan Vasilyev <grabesstimme@gmail.com> Tested-by: Ivan Vasilyev <grabesstimme@gmail.com> Fixes: f164cbf98fa8 ("staging: comedi: ni_mio_common: add finite regeneration to dio output") Cc: <stable@vger.kernel.org> # 4.6+ Cc: Spencer E. Olson <olsonse@umich.edu> Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suppose more than one non-NPIV FCP device is active on the same channel.
Send I/O to storage and have some of the pending I/O run into a SCSI
command timeout, e.g. due to bit errors on the fibre. Now the error
situation stops. However, we saw FCP requests continue to timeout in the
channel. The abort will be successful, but the subsequent TUR fails.
Scsi_eh starts. The LUN reset fails. The target reset fails. The host
reset only did an FCP device recovery. However, for non-NPIV FCP devices,
this does not close and reopen ports on the SAN-side if other non-NPIV FCP
device(s) share the same open ports.
In order to resolve the continuing FCP request timeouts, we need to
explicitly close and reopen ports on the SAN-side.
This was missing since the beginning of zfcp in v2.6.0 history commit ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.").
Note: The FSF requests for forced port reopen could run into FSF request
timeouts due to other reasons. This would trigger an internal FCP device
recovery. Pending forced port reopen recoveries would get dismissed. So
some ports might not get fully reopened during this host reset handler.
However, subsequent I/O would trigger the above described escalation and
eventually all ports would be forced reopen to resolve any continuing FCP
request timeouts due to earlier bit errors.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: <stable@vger.kernel.org> #3.0+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An already deleted SCSI device can exist on the Scsi_Host and remain there
because something still holds a reference. A new SCSI device with the same
H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When
we try to unblock an rport, we still find the deleted SCSI device and
return early because the zfcp_scsi_dev of that SCSI device is not
ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if
the new proper SCSI device would be in good state.
Therefore, skip deleted SCSI devices when iterating the sdevs of the shost.
[cf. __scsi_device_lookup{_by_target}() or scsi_device_get()]
The following abbreviated trace sequence can indicate such problem:
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED
Ready count : n not incremented yet
Running count : 0x00000000
ERP want : 0x01
ERP need : 0xc1 ZFCP_ERP_ACTION_NONE
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x41000000
Ready count : n+1
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
...
Area : REC
Level : 4 only with increased trace level
Tag : ertru_l
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000
Request ID : 0x0000000000000000
ERP status : 0x01800000
ERP step : 0x1000
ERP action : 0x01
ERP count : 0x00
NOT followed by a trace record with tag "scpaddy"
for WWPN 0x50050763031bd327.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery") Cc: <stable@vger.kernel.org> #2.6.32+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple
of physical block size") split one conditional into several separate
statements in an effort to provide more accurate warning messages when
a device reports a nonsensical value. However, this reorganization
accidentally dropped the precondition of the reported value being
larger than zero. This lead to a warning getting emitted on devices
that do not report an optimal I/O size at all.
Remain silent if a device does not report an optimal I/O size.
Fixes: a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of physical block size") Cc: Randy Dunlap <rdunlap@infradead.org> Cc: <stable@vger.kernel.org> Reported-by: Hussam Al-Tayeb <ht990332@gmx.com> Tested-by: Hussam Al-Tayeb <ht990332@gmx.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The scsi_end_request() function calls scsi_cmd_to_driver() indirectly and
hence needs the disk->private_data pointer. Avoid that that pointer is
cleared before all affected I/O requests have finished. This patch avoids
that the following crash occurs:
Cc: Christoph Hellwig <hch@lst.de> Cc: Ming Lei <ming.lei@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: Jason Yan <yanaijie@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reported-by: Jason Yan <yanaijie@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ocfs2_reflink_inodes_lock() can swap the inode1/inode2 variables so that
we always grab cluster locks in order of increasing inode number.
Unfortunately, we forget to swap the inode record buffer head pointers
when we've done this, which leads to incorrect bookkeepping when we're
trying to make the two inodes have the same refcount tree.
This has the effect of causing filesystem shutdowns if you're trying to
reflink data from inode 100 into inode 97, where inode 100 already has a
refcount tree attached and inode 97 doesn't. The reflink code decides
to copy the refcount tree pointer from 100 to 97, but uses inode 97's
inode record to open the tree root (which it doesn't have) and blows up.
This issue causes filesystem shutdowns and metadata corruption!
Link: http://lkml.kernel.org/r/20190312214910.GK20533@magnolia Fixes: 29ac8e856cb369 ("ocfs2: implement the VFS clone_range, copy_range, and dedupe_range features") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Joseph Qi <jiangqi903@gmail.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <joseph.qi@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is hitting lockdep warning [1] due to trying to open a fifo
during an execve() operation. But we don't need to open non regular
files during an execve() operation, for all files which we will need are
the executable file itself and the interpreter programs like /bin/sh and
ld-linux.so.2 .
Since the manpage for execve(2) says that execve() returns EACCES when
the file or a script interpreter is not a regular file, and the manpage
for uselib(2) says that uselib() can return EACCES, and we use
FMODE_EXEC when opening for execve()/uselib(), we can bail out if a non
regular file is requested with FMODE_EXEC set.
Since this deadlock followed by khungtaskd warnings is trivially
reproducible by a local unprivileged user, and syzbot's frequent crash
due to this deadlock defers finding other bugs, let's workaround this
deadlock until we get a chance to find a better solution.
Fix commit 56067812d5b0 ("kbuild: modversions: add infrastructure for
emitting relative CRCs") where CRCs are interpreted in host byte order
rather than proper kernel byte order. The bug is conditional on
CONFIG_MODULE_REL_CRCS.
For example, when loading a BE module into a BE kernel compiled with a LE
system, the error "disagrees about version of symbol module_layout" is
produced. A message such as "Found checksum D7FA6856 vs module 5668FAD7"
will be given with debug enabled, which indicates an obvious endian
problem within __kcrctab within the kernel image.
The general solution is to use the macro TO_NATIVE, as is done in
similar cases throughout modpost.c. With this correction it has been
verified that a BE kernel compiled with a LE system accepts BE modules.
This change has also been verified with a LE kernel compiled with a LE
system, in which case TO_NATIVE returns its value unmodified since the
byte orders match. This is by far the common case.
Currently PCM core sets each opened stream forcibly to SUSPENDED state
via snd_pcm_suspend_all() call, and the user-space is responsible for
re-triggering the resume manually either via snd_pcm_resume() or
prepare call. The scheme works fine usually, but there are corner
cases where the stream can't be resumed by that call: the streams
still in OPEN state before finishing hw_params. When they are
suspended, user-space cannot perform resume or prepare because they
haven't been set up yet. The only possible recovery is to re-open the
device, which isn't nice at all. Similarly, when a stream is in
DISCONNECTED state, it makes no sense to change it to SUSPENDED
state. Ditto for in SETUP state; which you can re-prepare directly.
So, this patch addresses these issues by filtering the PCM streams to
be suspended by checking the PCM state. When a stream is in either
OPEN, SETUP or DISCONNECTED as well as already SUSPENDED, the suspend
action is skipped.
To be noted, this problem was originally reported for the PCM runtime
PM on HD-audio. And, the runtime PM problem itself was already
addressed (although not intended) by the code refactoring commits 3d21ef0b49f8 ("ALSA: pcm: Suspend streams globally via device type PM
ops") and 17bc4815de58 ("ALSA: pci: Remove superfluous
snd_pcm_suspend*() calls"). These commits eliminated the
snd_pcm_suspend*() calls from the runtime PM suspend callback code
path, hence the racy OPEN state won't appear while runtime PM.
(FWIW, the race window is between snd_pcm_open_substream() and the
first power up in azx_pcm_open().)
Although the runtime PM issue was already "fixed", the same problem is
still present for the system PM, hence this patch is still needed.
And for stable trees, this patch alone should suffice for fixing the
runtime PM problem, too.
The PCM OSS emulation converts and transfers the data on the fly via
"plugins". The data is converted over the dynamically allocated
buffer for each plugin, and recently syzkaller caught OOB in this
flow.
Although the bisection by syzbot pointed out to the commit 65766ee0bf7f ("ALSA: oss: Use kvzalloc() for local buffer
allocations"), this is merely a commit to replace vmalloc() with
kvmalloc(), hence it can't be the cause. The further debug action
revealed that this happens in the case where a slave PCM doesn't
support only the stereo channels while the OSS stream is set up for a
mono channel. Below is a brief explanation:
At each OSS parameter change, the driver sets up the PCM hw_params
again in snd_pcm_oss_change_params_lock(). This is also the place
where plugins are created and local buffers are allocated. The
problem is that the plugins are created before the final hw_params is
determined. Namely, two snd_pcm_hw_param_near() calls for setting the
period size and periods may influence on the final result of channels,
rates, etc, too, while the current code has already created plugins
beforehand with the premature values. So, the plugin believes that
channels=1, while the actual I/O is with channels=2, which makes the
driver reading/writing over the allocated buffer size.
The fix is simply to move the plugin allocation code after the final
hw_params call.
Fix this by sanitizing dev before using it to index dp->synths.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Fix this by sanitizing info->stream before using it to index
rmidi->streams.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
This belated patch implements Andrew Lunn's request of
"remove the phy_read() and phy_write() functions."
<https://lore.kernel.org/patchwork/comment/902734/>
While seemingly harmless, this causes the switch's user
port PHYs to get registered twice. This is because the
DSA subsystem will create a slave mdio-bus not knowing
that the qca8k_phy_(read|write) accessors operate on
the external mdio-bus. So the same "bus" gets effectively
duplicated.
Cc: stable@vger.kernel.org Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yauheni Kaliuta pointed out that PTR_TO_STACK store/load verifier test
was failing on powerpc64 BE, and rightfully indicated that the PPC_LD()
macro is not masking away the last two bits of the offset per the ISA,
resulting in the generation of 'lwa' instruction instead of the intended
'ld' instruction.
Segher also pointed out that we can't simply mask away the last two bits
as that will result in loading/storing from/to a memory location that
was not intended.
This patch addresses this by using ldx/stdx if the offset is not
word-aligned. We load the offset into a temporary register (TMP_REG_2)
and use that as the index register in a subsequent ldx/stdx. We fix
PPC_LD() macro to mask off the last two bits, but enhance PPC_BPF_LL()
and PPC_BPF_STL() to factor in the offset value and generate the proper
instruction sequence. We also convert all existing users of PPC_LD() and
PPC_STD() to use these macros. All existing uses of these macros have
been audited to ensure that TMP_REG_2 can be clobbered.
Fixes: 156d0e290e96 ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF") Cc: stable@vger.kernel.org # v4.9+ Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current cpuidle implementation for i.MX6q, the CPU that sets
'WAIT_UNCLOCKED' and the CPU that returns to 'WAIT_CLOCKED' are always
the same. While the CPU that sets 'WAIT_UNCLOCKED' is in IDLE state of
"WAIT", if the other CPU wakes up and enters IDLE state of "WFI"
istead of "WAIT", this CPU can not wake up at expired time.
Because, in the case of "WFI", the CPU must be waked up by the local
timer interrupt. But, while 'WAIT_UNCLOCKED' is set, the local timer
is stopped, when all CPUs execute "wfi" instruction. As a result, the
local timer interrupt is not fired.
In this situation, this CPU will wake up by IRQ different from local
timer. (e.g. broacast timer)
So, this fix changes CPU to return to 'WAIT_CLOCKED'.
The reason is that kunmap(p_page) was completely left out, so we never
did an unmap for the p_page and the loop unmapping the rbio page was
iterating over the wrong number of stripes: unmapping should be done
with nr_data instead of rbio->real_stripes.
When Filipe added the recursive directory logging stuff in 2f2ff0ee5e430 ("Btrfs: fix metadata inconsistencies after directory
fsync") he specifically didn't take the directory i_mutex for the
children directories that we need to log because of lockdep. This is
generally fine, but can lead to this WARN_ON() tripping if we happen to
run delayed deletion's in between our first search and our second search
of dir_item/dir_indexes for this directory. We expect this to happen,
so the WARN_ON() isn't necessary. Drop the WARN_ON() and add a comment
so we know why this case can happen.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we do a shrinking truncate against an inode which is already present
in the respective log tree and then rename it, as part of logging the new
name we end up logging an inode item that reflects the old size of the
file (the one which we previously logged) and not the new smaller size.
The decision to preserve the size previously logged was added by commit 1a4bcf470c886b ("Btrfs: fix fsync data loss after adding hard link to
inode") in order to avoid data loss after replaying the log. However that
decision is only needed for the case the logged inode size is smaller then
the current size of the inode, as explained in that commit's change log.
If the current size of the inode is smaller then the previously logged
size, we know a shrinking truncate happened and therefore need to use
that smaller size.
$ mount /dev/sdb /mnt
$ od -t x1 -A d /mnt/bar 0000000 ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab
* 0008000
Once we rename the file, we log its name (and inode item), and because
the inode was already logged before in the current transaction, we log it
with a size of 8000 bytes because that is the size we previously logged
(with the first fsync). As part of the rename, besides logging the inode,
we do also sync the log, which is done since commit d4682ba03ef618
("Btrfs: sync log after logging new name"), so the next fsync against our
inode is effectively a no-op, since no new changes happened since the
rename operation. Even if did not sync the log during the rename
operation, the same problem (fize size of 8000 bytes instead of 3000
bytes) would be visible after replaying the log if the log ended up
getting synced to disk through some other means, such as for example by
fsyncing some other modified file. In the example above the fsync after
the rename operation is there just because not every filesystem may
guarantee logging/journalling the inode (and syncing the log/journal)
during the rename operation, for example it is needed for f2fs, but not
for ext4 and xfs.
Fix this scenario by, when logging a new name (which is triggered by
rename and link operations), using the current size of the inode instead
of the previously logged inode size.
A test case for fstests follows soon.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202695 CC: stable@vger.kernel.org # 4.4+ Reported-by: Seulbae Kim <seulbae@gatech.edu> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I updated the spectre_v2 reporting to handle software count cache
flush I got the logic wrong when there's no software count cache
enabled at all.
The result is that on systems with the software count cache flush
disabled we print:
Which correctly indicates that the count cache is disabled, but
incorrectly says the software count cache flush is enabled.
The root of the problem is that we are trying to handle all
combinations of options. But we know now that we only expect to see
the software count cache flush enabled if the other options are false.
So split the two cases, which simplifies the logic and fixes the bug.
We were also missing a space before "(hardware accelerated)".
The commit identified below adds MC_BTB_FLUSH macro only when
CONFIG_PPC_FSL_BOOK3E is defined. This results in the following error
on some configs (seen several times with kisskb randconfig_defconfig)
Fixed the following build warning:
powerpc-linux-gnu-ld: warning: orphan section `__btb_flush_fixup' from
`arch/powerpc/kernel/head_44x.o' being placed in section
`__btb_flush_fixup'.
projects / thirdparty / kernel / stable.git / log
