Petr Machata [Mon, 16 Jun 2025 22:44:18 +0000 (00:44 +0200)]
net: ipv6: Add ip6_mr_output()
Multicast routing is today handled in the input path. Locally generated MC
packets don't hit the IPMR code today. Thus if a VXLAN remote address is
multicast, the driver needs to set an OIF during route lookup. Thus MC
routing configuration needs to be kept in sync with the VXLAN FDB and MDB.
Ideally, the VXLAN packets would be routed by the MC routing code instead.
To that end, this patch adds support to route locally generated multicast
packets. The newly-added routines do largely what ip6_mr_input() and
ip6_mr_forward() do: make an MR cache lookup to find where to send the
packets, and use ip6_output() to send each of them. When no cache entry is
found, the packet is punted to the daemon for resolution.
Similarly to the IPv4 case in a previous patch, the new logic is contingent
on a newly-added IP6CB flag being set.
Petr Machata [Mon, 16 Jun 2025 22:44:17 +0000 (00:44 +0200)]
net: ipv6: ip6mr: Split ip6mr_forward2() in two
Some of the work of ip6mr_forward2() is specific to IPMR forwarding, and
should not take place on the output path. In order to allow reuse of the
common parts, extract out of the function a helper,
ip6mr_prepare_forward().
Petr Machata [Mon, 16 Jun 2025 22:44:15 +0000 (00:44 +0200)]
net: ipv6: ip6mr: Fix in/out netdev to pass to the FORWARD chain
The netfilter hook is invoked with skb->dev for input netdevice, and
vif_dev for output netdevice. However at the point of invocation, skb->dev
is already set to vif_dev, and MR-forwarded packets are reported with
in=out:
Petr Machata [Mon, 16 Jun 2025 22:44:14 +0000 (00:44 +0200)]
net: ipv6: Add a flags argument to ip6tunnel_xmit(), udp_tunnel6_xmit_skb()
ip6tunnel_xmit() erases the contents of the SKB control block. In order to
be able to set particular IP6CB flags on the SKB, add a corresponding
parameter, and propagate it to udp_tunnel6_xmit_skb() as well.
In one of the following patches, VXLAN driver will use this facility to
mark packets as subject to IPv6 multicast routing.
Petr Machata [Mon, 16 Jun 2025 22:44:13 +0000 (00:44 +0200)]
net: ipv6: Make udp_tunnel6_xmit_skb() void
The function always returns zero, thus the return value does not carry any
signal. Just make it void.
Most callers already ignore the return value. However:
- Refold arguments of the call from sctp_v6_xmit() so that they fit into
the 80-column limit.
- tipc_udp_xmit() initializes err from the return value, but that should
already be always zero at that point. So there's no practical change, but
elision of the assignment prompts a couple more tweaks to clean up the
function.
Petr Machata [Mon, 16 Jun 2025 22:44:12 +0000 (00:44 +0200)]
net: ipv4: Add ip_mr_output()
Multicast routing is today handled in the input path. Locally generated MC
packets don't hit the IPMR code today. Thus if a VXLAN remote address is
multicast, the driver needs to set an OIF during route lookup. Thus MC
routing configuration needs to be kept in sync with the VXLAN FDB and MDB.
Ideally, the VXLAN packets would be routed by the MC routing code instead.
To that end, this patch adds support to route locally generated multicast
packets. The newly-added routines do largely what ip_mr_input() and
ip_mr_forward() do: make an MR cache lookup to find where to send the
packets, and use ip_mc_output() to send each of them. When no cache entry
is found, the packet is punted to the daemon for resolution.
However, an installation that uses a VXLAN underlay netdevice for which it
also has matching MC routes, would get a different routing with this patch.
Previously, the MC packets would be delivered directly to the underlay
port, whereas now they would be MC-routed. In order to avoid this change in
behavior, introduce an IPCB flag. Only if the flag is set will
ip_mr_output() actually engage, otherwise it reverts to ip_mc_output().
This code is based on work by Roopa Prabhu and Nikolay Aleksandrov.
Signed-off-by: Roopa Prabhu <roopa@nvidia.com> Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/0aadbd49330471c0f758d54afb05eb3b6e3a6b65.1750113335.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata [Mon, 16 Jun 2025 22:44:11 +0000 (00:44 +0200)]
net: ipv4: ipmr: Split ipmr_queue_xmit() in two
Some of the work of ipmr_queue_xmit() is specific to IPMR forwarding, and
should not take place on the output path. In order to allow reuse of the
common parts, split the function into two: the ipmr_prepare_xmit() helper
that takes care of the common bits, and the ipmr_queue_fwd_xmit(), which
invokes the former and encapsulates the whole forwarding algorithm.
Petr Machata [Mon, 16 Jun 2025 22:44:10 +0000 (00:44 +0200)]
net: ipv4: ipmr: ipmr_queue_xmit(): Drop local variable `dev'
The variable is used for caching of rt->dst.dev. The netdevice referenced
therein does not change during the scope of validity of that local. At the
same time, the local is only used twice, and each of these uses will end up
in a different function in the following patches, further eliminating any
use the local could have had.
Petr Machata [Mon, 16 Jun 2025 22:44:09 +0000 (00:44 +0200)]
net: ipv4: Add a flags argument to iptunnel_xmit(), udp_tunnel_xmit_skb()
iptunnel_xmit() erases the contents of the SKB control block. In order to
be able to set particular IPCB flags on the SKB, add a corresponding
parameter, and propagate it to udp_tunnel_xmit_skb() as well.
In one of the following patches, VXLAN driver will use this facility to
mark packets as subject to IP multicast routing.
Jakub Kicinski [Wed, 18 Jun 2025 01:06:42 +0000 (18:06 -0700)]
Merge branch 'misc-vlan-cleanups'
Gal Pressman says:
====================
Misc vlan cleanups
This patch series addresses compilation issues with objtool when VLAN
support is disabled (CONFIG_VLAN_8021Q=n) and makes related improvements
to the VLAN infrastructure.
When CONFIG_VLAN_8021Q=n, CONFIG_OBJTOOL=y, and CONFIG_OBJTOOL_WERROR=y,
the following compilation error occurs:
drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.o: error: objtool: parse_mirred.isra.0+0x370: mlx5e_tc_act_vlan_add_push_action() missing __noreturn in .c/.h or NORETURN() in noreturns.h
The error occurs because objtool cannot determine that unreachable BUG()
calls in VLAN code paths are actually dead code when VLAN support is
disabled.
First patch makes is_vlan_dev() a stub when VLAN is not configured,
allows compile-out of VLAN-dependent dead code paths and resolves the
objtool compilation error.
Second patch replaces BUG() calls with WARN_ON_ONCE(), as the usage of
BUG() should be avoided.
Third patch uses the "kernel" way of testing whether an option is
configured as builtin/module, instead of open-coding it.
Gal Pressman [Mon, 16 Jun 2025 13:26:26 +0000 (16:26 +0300)]
net: vlan: Use IS_ENABLED() helper for CONFIG_VLAN_8021Q guard
The header currently tests the VLAN core with an explicit pair of 'if
defined' checks:
#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
Instead, use IS_ENABLED() which is the kernel way to test whether an
option is configured as builtin/module.
This is purely cosmetic – no functional changes.
Reviewed-by: Alex Lazar <alazar@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Link: https://patch.msgid.link/20250616132626.1749331-4-gal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Mon, 16 Jun 2025 13:26:25 +0000 (16:26 +0300)]
net: vlan: Replace BUG() with WARN_ON_ONCE() in vlan_dev_* stubs
When CONFIG_VLAN_8021Q=n, a set of stub helpers are used, three of these
helpers use BUG() unconditionally.
This code should not be reached, as callers of these functions should
always check for is_vlan_dev() first, but the usage of BUG() is not
recommended, replace it with WARN_ON() instead.
Reviewed-by: Alex Lazar <alazar@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Link: https://patch.msgid.link/20250616132626.1749331-3-gal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Mon, 16 Jun 2025 13:26:24 +0000 (16:26 +0300)]
net: vlan: Make is_vlan_dev() a stub when VLAN is not configured
Add a stub implementation of is_vlan_dev() that returns false when
VLAN support is not compiled in (CONFIG_VLAN_8021Q=n).
This allows us to compile-out VLAN-dependent dead code when it is not
needed.
This also resolves the following compilation error when:
* CONFIG_VLAN_8021Q=n
* CONFIG_OBJTOOL=y
* CONFIG_OBJTOOL_WERROR=y
drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.o: error: objtool: parse_mirred.isra.0+0x370: mlx5e_tc_act_vlan_add_push_action() missing __noreturn in .c/.h or NORETURN() in noreturns.h
The error occurs because objtool cannot determine that unreachable BUG()
(which doesn't return) calls in VLAN code paths are actually dead code
when VLAN support is disabled.
====================
net: use new GPIO line value setter callbacks
Commit 98ce1eb1fd87e ("gpiolib: introduce gpio_chip setters that return
values") added new line setter callbacks to struct gpio_chip. They allow
to indicate failures to callers. We're in the process of converting all
GPIO controllers to using them before removing the old ones. This series
converts all GPIO chips implemented under drivers/net/.
net: can: mcp251x: propagate the return value of mcp251x_spi_write()
Add an integer return value to mcp251x_write_bits() and use it to
propagate the one returned by mcp251x_spi_write(). Return that value on
error in the request() GPIO callback.
Alok Tiwari [Mon, 16 Jun 2025 05:45:01 +0000 (22:45 -0700)]
gve: Return error for unknown admin queue command
In gve_adminq_issue_cmd(), return -EINVAL instead of 0 when an unknown
admin queue command opcode is encountered.
This prevents the function from silently succeeding on invalid input
and prevents undefined behavior by ensuring the function fails gracefully
when an unrecognized opcode is provided.
Alok Tiwari [Mon, 16 Jun 2025 05:45:00 +0000 (22:45 -0700)]
gve: Fix various typos and improve code comments
- Correct spelling and improves the clarity of comments
"confiugration" -> "configuration"
"spilt" -> "split"
"It if is 0" -> "If it is 0"
"DQ" -> "DQO" (correct abbreviation)
- Clarify BIT(0) flag usage in gve_get_priv_flags()
- Replaced hardcoded array size with GVE_NUM_PTYPES
for clarity and maintainability.
These changes are purely cosmetic and do not affect functionality.
Yuyang Huang [Sat, 14 Jun 2025 05:35:22 +0000 (14:35 +0900)]
selftest: Add selftest for multicast address notifications
This commit adds a new kernel selftest to verify RTNLGRP_IPV4_MCADDR
and RTNLGRP_IPV6_MCADDR notifications. The test works by adding and
removing a dummy interface and then confirming that the system
correctly receives join and removal notifications for the 224.0.0.1
and ff02::1 multicast addresses.
The test relies on the iproute2 version to be 6.13+.
Tested by the following command:
$ vng -v --user root --cpus 16 -- \
make -C tools/testing/selftests TARGETS=net
TEST_PROGS=rtnetlink_notification.sh \
TEST_GEN_PROGS="" run_tests
Jakub Kicinski [Wed, 18 Jun 2025 00:52:32 +0000 (17:52 -0700)]
Merge branch 'net-dsa-b53-fix-bcm5325-support'
Álvaro Fernández Rojas says:
====================
net: dsa: b53: fix BCM5325 support
These patches get the BCM5325 switch working with b53.
The existing brcm legacy tag only works with BCM63xx switches.
We need to add a new legacy tag for BCM5325 and BCM5365 switches, which
require including the FCS and length.
I'm not really sure that everything here is correct since I don't work for
Broadcom and all this is based on the public datasheet available for the
BCM5325 and my own experiments with a Huawei HG556a (BCM6358).
Both sets of patches have been merged due to the change requested by Jonas
about BRCM_HDR register access depending on legacy tags.
====================
According to the datasheet, BCM5325 uses B53_PD_MODE_CTRL_25 register to
disable clocking to individual PHYs.
Only ports 1-4 can be enabled or disabled and the datasheet is explicit
about not toggling BIT(0) since it disables the PLL power and the switch.
net: dsa: b53: fix unicast/multicast flooding on BCM5325
BCM5325 doesn't implement UC_FLOOD_MASK, MC_FLOOD_MASK and IPMC_FLOOD_MASK
registers.
This has to be handled differently with other pages and registers.
net: dsa: b53: prevent GMII_PORT_OVERRIDE_CTRL access on BCM5325
BCM5325 doesn't implement GMII_PORT_OVERRIDE_CTRL register so we should
avoid reading or writing it.
PORT_OVERRIDE_RX_FLOW and PORT_OVERRIDE_TX_FLOW aren't defined on BCM5325
and we should use PORT_OVERRIDE_LP_FLOW_25 instead.
Florian Fainelli [Sat, 14 Jun 2025 07:59:51 +0000 (09:59 +0200)]
net: dsa: b53: add support for FDB operations on 5325/5365
BCM5325 and BCM5365 are part of a much older generation of switches which,
due to their limited number of ports and VLAN entries (up to 256) allowed
a single 64-bit register to hold a full ARL entry.
This requires a little bit of massaging when reading, writing and
converting ARL entries in both directions.
We need to be able to differentiate the BCM5325 variants because:
- BCM5325M switches lack the ARLIO_PAGE->VLAN_ID_IDX register.
- BCM5325E have less 512 ARL buckets instead of 1024.
Commit 46c5176c586c ("net: dsa: b53: support legacy tags") introduced
support for legacy tags, but it turns out that BCM5325 and BCM5365
switches require the original FCS value and length, so they have to be
treated differently.
net: dsa: tag_brcm: add support for legacy FCS tags
Add support for legacy Broadcom FCS tags, which are similar to
DSA_TAG_PROTO_BRCM_LEGACY.
BCM5325 and BCM5365 switches require including the original FCS value and
length, as opposed to BCM63xx switches.
Adding the original FCS value and length to DSA_TAG_PROTO_BRCM_LEGACY would
impact performance of BCM63xx switches, so it's better to create a new tag.
There is little need to have phy_intf_sel as a member of struct
visconti_eth when we have the PHY interface mode available from
phylink in visconti_eth_set_clk_tx_rate(). Without multiple
interface support, phylink is fixed to supporting only
plat->phy_interface, so we can be sure that "interface" passed
into this function is the same as plat->phy_interface.
Make phy_intf_sel local to visconti_eth_init_hw() and clean up.
Rather than testing dwmac->phy_intf_sel several times for the same
values in this function, group the code together. The only part
which was common was stopping the internal clock before programming
the clock setting.
This further improves the readability of this function.
Re-arrange the speed decode in visconti_eth_set_clk_tx_rate() to be
more readable by first checking to see if we're using RGMII or RMII
and then decoding the speed, rather than decoding the speed and then
testing the interface mode.
====================
Link NAPI instances to queues and IRQs
This patch series introduces netdev-genl support to rtase, enabling
user-space applications to query the relationships between IRQs,
queues, and NAPI instances.
====================
Alok Tiwari [Sun, 15 Jun 2025 08:48:12 +0000 (01:48 -0700)]
selftests: nettest: Fix typo in log and error messages for clarity
This patch corrects several logging and error message in nettest.c:
- Corrects function name in log messages "setsockopt" -> "getsockopt".
- Closes missing parentheses in "setsockopt(IPV6_FREEBIND)".
- Replaces misleading error text ("Invalid port") with the correct
description ("Invalid prefix length").
- remove Redundant wording like "status from status" and clarifies
context in IPC error messages.
These changes improve readability and aid in debugging test output.
RACK-TLP loss detection has been enabled as the default loss detection
algorithm for Linux TCP since 2018, in:
commit b38a51fec1c1 ("tcp: disable RFC6675 loss detection")
In case users ran into unexpected bugs or performance regressions,
that commit allowed Linux system administrators to revert to using
RFC3517/RFC6675 loss recovery by setting net.ipv4.tcp_recovery to 0.
In the seven years since 2018, our team has not heard reports of
anyone reverting Linux TCP to use RFC3517/RFC6675 loss recovery, and
we can't find any record in web searches of such a revert.
RACK-TLP was published as a standards-track RFC, RFC8985, in February
2021.
Several other major TCP implementations have default-enabled RACK-TLP
at this point as well.
RACK-TLP offers several significant performance advantages over
RFC3517/RFC6675 loss recovery, including much better performance in
the common cases of tail drops, lost retransmissions, and reordering.
It is now time to remove the obsolete and unused RFC3517/RFC6675 loss
recovery code. This will allow a substantial simplification of the
Linux TCP code base, and removes 12 bytes of state in every tcp_sock
for 64-bit machines (8 bytes on 32-bit machines).
To arrange the commits in reasonable sizes, this patch series is split
into 3 commits:
(1) Removes the core RFC3517/RFC6675 logic.
(2) Removes the RFC3517/RFC6675 hint state and the first layer of logic that
updates that state.
(3) Removes the emptied-out tcp_clear_retrans_hints_partial() helper function
and all of its call sites.
====================
Neal Cardwell [Sun, 15 Jun 2025 00:14:34 +0000 (20:14 -0400)]
tcp: remove RFC3517/RFC6675 hint state: lost_skb_hint, lost_cnt_hint
Now that obsolete RFC3517/RFC6675 TCP loss detection has been removed,
we can remove the somewhat complex and intrusive code to maintain its
hint state: lost_skb_hint and lost_cnt_hint.
This commit makes tcp_clear_retrans_hints_partial() empty. We will
remove tcp_clear_retrans_hints_partial() and its call sites in the
next commit.
Neal Cardwell [Sun, 15 Jun 2025 00:14:33 +0000 (20:14 -0400)]
tcp: remove obsolete and unused RFC3517/RFC6675 loss recovery code
RACK-TLP loss detection has been enabled as the default loss detection
algorithm for Linux TCP since 2018, in:
commit b38a51fec1c1 ("tcp: disable RFC6675 loss detection")
In case users ran into unexpected bugs or performance regressions,
that commit allowed Linux system administrators to revert to using
RFC3517/RFC6675 loss recovery by setting net.ipv4.tcp_recovery to 0.
In the seven years since 2018, our team has not heard reports of
anyone reverting Linux TCP to use RFC3517/RFC6675 loss recovery, and
we can't find any record in web searches of such a revert.
RACK-TLP was published as a standards-track RFC, RFC8985, in February
2021.
Several other major TCP implementations have default-enabled RACK-TLP
at this point as well.
RACK-TLP offers several significant performance advantages over
RFC3517/RFC6675 loss recovery, including much better performance in
the common cases of tail drops, lost retransmissions, and reordering.
It is now time to remove the obsolete and unused RFC3517/RFC6675 loss
recovery code. This will allow a substantial simplification of the
Linux TCP code base, and removes 12 bytes of state in every tcp_sock
for 64-bit machines (8 bytes on 32-bit machines).
To arrange the commits in reasonable sizes, this patch series is split
into 3 commits. The following 2 commits remove bookkeeping state and
code that is no longer needed after this removal of RFC3517/RFC6675
loss recovery.
Doug Berger [Sat, 14 Jun 2025 02:58:16 +0000 (19:58 -0700)]
net: bcmgenet: update PHY power down
The disable sequence in bcmgenet_phy_power_set() is updated to
match the inverse sequence and timing (and spacing) of the
enable sequence. This ensures that LEDs driven by the GENET IP
are disabled when the GPHY is powered down.
[Note, I'm wondering if actually this is a case of a missing call;
the other similar function is called in __verify_octeon_config_info(),
but I don't have or know the hardware.]
validate_cn23xx_pf_config_info() was added in 2016 by
commit 72c0091293c0 ("liquidio: CN23XX device init and sriov config")
The stmmac platform code already gets the "stmmaceth" clock, so there
is no need for drivers to get it. Use the stored pointer in struct
plat_stmmacenet_data instead of getting and storing our own pointer.
net: stmmac: rk: use device rather than platform device in rk_priv_data
All the code in dwmac-rk uses &bsp_priv->pdev->dev, nothing uses
bsp_priv->pdev directly. Store the struct device rather than the
struct platform_device in struct rk_priv_data, and simplifying the
code.
====================
vsock/test: Improve transport_uaf test
Increase the coverage of a test implemented in commit 301a62dfb0d0
("vsock/test: Add test for UAF due to socket unbinding"). Take this
opportunity to factor out some utility code, drop a redundant sync between
client and server, and introduce a /proc/kallsyms harvesting logic for
auto-detecting registered vsock transports.
Michal Luczaj [Wed, 11 Jun 2025 19:56:52 +0000 (21:56 +0200)]
vsock/test: Cover more CIDs in transport_uaf test
Increase the coverage of test for UAF due to socket unbinding, and losing
transport in general. It's a follow up to commit 301a62dfb0d0 ("vsock/test:
Add test for UAF due to socket unbinding") and discussion in [1].
The idea remains the same: take an unconnected stream socket with a
transport assigned and then attempt to switch the transport by trying (and
failing) to connect to some other CID. Now do this iterating over all the
well known CIDs (plus one).
While at it, drop the redundant synchronization between client and server.
Some single-transport setups can't be tested effectively; a warning is
issued. Depending on transports available, a variety of splats are possible
on unpatched machines. After reverting commit 78dafe1cf3af ("vsock: Orphan
socket after transport release") and commit fcdd2242c023 ("vsock: Keep the
binding until socket destruction"):
BUG: KASAN: slab-use-after-free in __vsock_bind+0x61f/0x720
Read of size 4 at addr ffff88811ff46b54 by task vsock_test/1475
Call Trace:
dump_stack_lvl+0x68/0x90
print_report+0x170/0x53d
kasan_report+0xc2/0x180
__vsock_bind+0x61f/0x720
vsock_connect+0x727/0xc40
__sys_connect+0xe8/0x100
__x64_sys_connect+0x6e/0xc0
do_syscall_64+0x92/0x1c0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Michal Luczaj [Wed, 11 Jun 2025 19:56:51 +0000 (21:56 +0200)]
vsock/test: Introduce get_transports()
Return a bitmap of registered vsock transports. As guesstimated by grepping
/proc/kallsyms (CONFIG_KALLSYMS=y) for known symbols of type `struct
vsock_transport`, or `struct virtio_transport` in case the vsock_transport
is embedded within.
Note that the way `enum transport` and `transport_ksyms[]` are defined
triggers checkpatch.pl:
util.h:11: ERROR: Macros with complex values should be enclosed in parentheses
util.h:20: ERROR: Macros with complex values should be enclosed in parentheses
util.h:20: WARNING: Argument 'symbol' is not used in function-like macro
util.h:28: WARNING: Argument 'name' is not used in function-like macro
While commit 15d4734c7a58 ("checkpatch: qualify do-while-0 advice")
suggests it is known that the ERRORs heuristics are insufficient, I can not
find many other places where preprocessor is used in this
checkpatch-unhappy fashion. Notable exception being bcachefs, e.g.
fs/bcachefs/alloc_background_format.h. WARNINGs regarding unused macro
arguments seem more common, e.g. __ASM_SEL in arch/x86/include/asm/asm.h.
In other words, this might be unnecessarily complex. The same can be
achieved by just telling human to keep the order:
Jakub Kicinski [Tue, 17 Jun 2025 21:43:58 +0000 (14:43 -0700)]
Merge branch 'shradha_v6.16-rc1' of https://github.com/shradhagupta6/linux
Shradha Gupta says:
====================
Allow dyn MSI-X vector allocation of MANA
In this patchset we want to enable the MANA driver to be able to
allocate MSI-X vectors in PCI dynamically.
The first patch exports pci_msix_prepare_desc() in PCI to be able to
correctly prepare descriptors for dynamically added MSI-X vectors.
The second patch adds the support of dynamic vector allocation in
pci-hyperv PCI controller by enabling the MSI_FLAG_PCI_MSIX_ALLOC_DYN
flag and using the pci_msix_prepare_desc() exported in first patch.
The third patch adds a detailed description of the irq_setup(), to
help understand the function design better.
The fourth patch is a preparation patch for mana changes to support
dynamic IRQ allocation. It contains changes in irq_setup() to allow
skipping first sibling CPU sets, in case certain IRQs are already
affinitized to them.
The fifth patch has the changes in MANA driver to be able to allocate
MSI-X vectors dynamically. If the support does not exist it defaults to
older behavior.
* 'shradha_v6.16-rc1' of https://github.com/shradhagupta6/linux:
net: mana: Allocate MSI-X vectors dynamically
net: mana: Allow irq_setup() to skip cpus for affinity
net: mana: explain irq_setup() algorithm
PCI: hv: Allow dynamic MSI-X vector allocation
PCI/MSI: Export pci_msix_prepare_desc() for dynamic MSI-X allocations
====================
Paolo Abeni [Tue, 17 Jun 2025 12:58:47 +0000 (14:58 +0200)]
Merge branch 'intel-next-queue-1GbE'
Tony Nguyen says:
====================
Faizal Rahim says:
MAC Merge support for frame preemption was previously added for igc:
https://lore.kernel.org/netdev/20250418163822.3519810-1-anthony.l.nguyen@intel.com/
This series builds on that work and adds support for:
- Harmonizing taprio and mqprio queue priority behavior, based on past
discussions and suggestions:
https://lore.kernel.org/all/20250214102206.25dqgut5tbak2rkz@skbuf/
- Enabling preemptible queue support for both taprio and mqprio, with
priority harmonization as a prerequisite.
Patch organization:
- Patches 1-3: Preparation work for patches 6 and 7
- Patches 4-5: Queue priority harmonization
- Patches 6-7: Add preemptible queue support
====================
Wei Fang [Fri, 13 Jun 2025 09:36:05 +0000 (17:36 +0800)]
net: enetc: replace PCVLANR1/2 with SICVLANR1/2 and remove dead branch
Both PF and VF have rx-vlan-offload enabled, however, the PCVLANR1/2
registers are resources controlled by PF, so VF cannot access these
two registers. Fortunately, the hardware provides SICVLANR1/2 registers
for each SI to reflect the value of PCVLANR1/2 registers. Therefore,
use SICVLANR1/2 instead of PCVLANR1/2. Note that this is not an issue
in actual use, because the current driver does not support custom TPID,
the driver will not access these two registers in actual use, so this
modification is just an optimization.
In addition, since ENETC_RXBD_FLAG_TPID is defined as GENMASK(1, 0),
the possible values are only 0, 1, 2, 3, so the default branch will
never be true, so remove the default branch.
Shradha Gupta [Wed, 11 Jun 2025 14:11:13 +0000 (07:11 -0700)]
net: mana: Allocate MSI-X vectors dynamically
Currently, the MANA driver allocates MSI-X vectors statically based on
MANA_MAX_NUM_QUEUES and num_online_cpus() values and in some cases ends
up allocating more vectors than it needs. This is because, by this time
we do not have a HW channel and do not know how many IRQs should be
allocated.
To avoid this, we allocate 1 MSI-X vector during the creation of HWC and
after getting the value supported by hardware, dynamically add the
remaining MSI-X vectors.
Shradha Gupta [Wed, 11 Jun 2025 14:10:42 +0000 (07:10 -0700)]
net: mana: Allow irq_setup() to skip cpus for affinity
In order to prepare the MANA driver to allocate the MSI-X IRQs
dynamically, we need to enhance irq_setup() to allow skipping
affinitizing IRQs to the first CPU sibling group.
This would be for cases when the number of IRQs is less than or equal
to the number of online CPUs. In such cases for dynamically added IRQs
the first CPU sibling group would already be affinitized with HWC IRQ.
Yury Norov [Wed, 11 Jun 2025 14:10:29 +0000 (07:10 -0700)]
net: mana: explain irq_setup() algorithm
Commit 91bfe210e196 ("net: mana: add a function to spread IRQs per CPUs")
added the irq_setup() function that distributes IRQs on CPUs according
to a tricky heuristic. The corresponding commit message explains the
heuristic.
Duplicate it in the source code to make available for readers without
digging git in history. Also, add more detailed explanation about how
the heuristics is implemented.
Shradha Gupta [Wed, 11 Jun 2025 14:10:15 +0000 (07:10 -0700)]
PCI: hv: Allow dynamic MSI-X vector allocation
Allow dynamic MSI-X vector allocation for pci_hyperv PCI controller
by adding support for the flag MSI_FLAG_PCI_MSIX_ALLOC_DYN and using
pci_msix_prepare_desc() to prepare the MSI-X descriptors.
Shradha Gupta [Wed, 11 Jun 2025 14:10:01 +0000 (07:10 -0700)]
PCI/MSI: Export pci_msix_prepare_desc() for dynamic MSI-X allocations
For supporting dynamic MSI-X vector allocation by PCI controllers, enabling
the flag MSI_FLAG_PCI_MSIX_ALLOC_DYN is not enough, msix_prepare_msi_desc()
to prepare the MSI descriptor is also needed.
Export pci_msix_prepare_desc() to allow PCI controllers to support dynamic
MSI-X vector allocation.
Jakub Kicinski [Fri, 13 Jun 2025 17:27:51 +0000 (10:27 -0700)]
eth: gianfar: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
Uniquely, this driver supports only the SET operation. It does not
support GET at all. The SET callback also always returns 0, even
tho it checks a bunch of conditions, and if my quick reading is
right, expects the user to insert filtering rules for given flow
type first? Long story short it seems too convoluted to easily
add the GET as part of the conversion.
Heiner Kallweit [Sat, 14 Jun 2025 20:31:57 +0000 (22:31 +0200)]
net: phy: improve phy_driver_is_genphy
Use new flag phydev->is_genphy_driven to simplify this function.
Note that this includes a minor functional change:
Now this function returns true if ANY of the genphy drivers
is bound to the PHY device.
We have only one user in DSA driver mt7530, and there the
functional change doesn't matter.
====================
eth: intel: migrate to new RXFH callbacks
Migrate Intel drivers to the recently added dedicated .get_rxfh_fields
and .set_rxfh_fields ethtool callbacks.
Note that I'm deleting all the boilerplate kdoc from the affected
functions in the more recent drivers. If the maintainers feel strongly
I can respin and add it back, but it really feels useless and undue
burden for refactoring. No other vendor does this.
Jakub Kicinski [Sat, 14 Jun 2025 18:09:07 +0000 (11:09 -0700)]
eth: iavf: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
I'm deleting all the boilerplate kdoc from the affected functions.
It is somewhere between pointless and incorrect, just a burden for
people refactoring the code.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Joe Damato <joe@dama.to> Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250614180907.4167714-8-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 14 Jun 2025 18:09:06 +0000 (11:09 -0700)]
eth: ice: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
I'm deleting all the boilerplate kdoc from the affected functions.
It is somewhere between pointless and incorrect, just a burden for
people refactoring the code.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Joe Damato <joe@dama.to> Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250614180907.4167714-7-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 14 Jun 2025 18:09:05 +0000 (11:09 -0700)]
eth: i40e: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
I'm deleting all the boilerplate kdoc from the affected functions.
It is somewhere between pointless and incorrect, just a burden for
people refactoring the code.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Joe Damato <joe@dama.to> Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250614180907.4167714-6-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 14 Jun 2025 18:09:04 +0000 (11:09 -0700)]
eth: fm10k: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
.get callback moves out of the switch and set_rxnfc disappears
as ETHTOOL_SRXFH as the only functionality.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Joe Damato <joe@dama.to> Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250614180907.4167714-5-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 14 Jun 2025 18:09:03 +0000 (11:09 -0700)]
eth: ixgbe: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Joe Damato <joe@dama.to> Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250614180907.4167714-4-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 14 Jun 2025 18:09:02 +0000 (11:09 -0700)]
eth: igc: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Joe Damato <joe@dama.to> Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250614180907.4167714-3-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 14 Jun 2025 18:09:01 +0000 (11:09 -0700)]
eth: igb: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Joe Damato <joe@dama.to> Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250614180907.4167714-2-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 14 Jun 2025 18:06:38 +0000 (11:06 -0700)]
eth: enetc: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
This driver's RXFH config is read only / fixed so the conversion
is trivial.
Jakub Kicinski [Sat, 14 Jun 2025 18:06:37 +0000 (11:06 -0700)]
eth: e1000e: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
This driver's RXFH config is read only / fixed and it's the only
get_rxnfc sub-command the driver supports. So convert the get_rxnfc
handler into a get_rxfh_fields handler.
Jakub Kicinski [Sat, 14 Jun 2025 18:06:36 +0000 (11:06 -0700)]
eth: lan743x: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
This driver's RXFH config is read only / fixed so the conversion
is purely factoring out the handling into a helper.
Jakub Kicinski [Sat, 14 Jun 2025 18:06:35 +0000 (11:06 -0700)]
eth: cxgb4: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
This driver's RXFH config is read only / fixed so the conversion
is purely factoring out the handling into a helper.
Jakub Kicinski [Sat, 14 Jun 2025 18:06:34 +0000 (11:06 -0700)]
eth: cisco: migrate to new RXFH callbacks
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
This driver's RXFH config is read only / fixed so the conversion
is trivial.
Jakub Kicinski [Tue, 17 Jun 2025 00:37:54 +0000 (17:37 -0700)]
Merge branch 'cn20k-silicon-with-mbox-support'
Subbaraya Sundeep says:
====================
CN20K silicon with mbox support
CN20K is the next generation silicon in the Octeon series with various
improvements and new features.
Along with other changes the mailbox communication mechanism between RVU
(Resource virtualization Unit) SRIOV PFs/VFs with Admin function (AF) has
also gone through some changes.
Some of those changes are
- Separate IRQs for mbox request and response/ack.
- Configurable mbox size, default being 64KB.
- Ability for VFs to communicate with RVU AF instead of going through
parent SRIOV PF.
Due to more memory requirement due to configurable mbox size, mbox memory
will now have to be allocated by
- AF (PF0) for communicating with other PFs and all VFs in the system.
- PF for communicating with it's child VFs.
On previous silicons mbox memory was reserved and configured by firmware.
This patch series add basic mbox support for AF (PF0) <=> PFs and
PF <=> VFs. AF <=> VFs communication and variable mbox size support will
come in later.
Patch #1 Supported co-existance of bit encoding PFs and VFs in 16-bit
hardware pcifunc format between CN20K silicon and older octeon
series. Also exported PF,VF masks and shifts present in mailbox
module to all other modules.
Patch #2 Added basic mbox operation APIs and structures to support both
CN20K and previous version of silicons.
Patch #3 This patch adds support for basic mbox infrastructure
implementation for CN20K silicon in AF perspective. There are
few updates w.r.t MBOX ACK interrupt and offsets in CN20k.
Patch #4 Added mbox implementation between NIC PF and AF for CN20K.
Patch #5 Added mbox communication support between AF and AF's VFs.
Patch #6 This patch adds support for MBOX communication between NIC PF and
its VFs.
====================
Sai Krishna [Wed, 11 Jun 2025 11:01:56 +0000 (16:31 +0530)]
octeontx2-pf: CN20K mbox implementation between PF-VF
This patch implements the CN20k MBOX communication between PF and
it's VFs. CN20K silicon got extra interrupt of MBOX response for trigger
interrupt. Also few of the CSR offsets got changed in CN20K against
prior series of silicons.
Sai Krishna [Wed, 11 Jun 2025 11:01:55 +0000 (16:31 +0530)]
octeontx2-af: CN20K mbox implementation for AF's VF
This patch implements the CN20k MBOX communication between AF and
AF's VFs. This implementation uses separate trigger interrupts
for request, response messages against using trigger message data in CN10K.
Sai Krishna [Wed, 11 Jun 2025 11:01:54 +0000 (16:31 +0530)]
octeontx2-pf: CN20K mbox REQ/ACK implementation for NIC PF
This implementation uses separate trigger interrupts for request,
response messages against using trigger message data in CN10K.
This patch adds support for basic mbox implementation for CN20K
from NIC PF side.
Sai Krishna [Wed, 11 Jun 2025 11:01:53 +0000 (16:31 +0530)]
octeontx2-af: CN20k mbox to support AF REQ/ACK functionality
This implementation uses separate trigger interrupts for request,
response MBOX messages against using trigger message data in CN10K.
This patch adds support for basic mbox implementation for CN20K
from AF side.
projects / thirdparty / linux.git / log
