Fix all the remaining dtc 'unit_address_format' warnings except for the ones
related to 'register-bit-led'. For those, we need to decide on and document
the node name.
Arnd Bergmann [Wed, 18 Aug 2021 12:47:31 +0000 (14:47 +0200)]
Merge tag 'mvebu-dt64-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt64 for 5.15 (part 1)
- DTS updates for Marvell Armada CN913x platforms
+ Add support for Armada CN913x Development Board topology "B"
+ Add support for Armada CN913x Reference Design boards (CRB)
+ Fixes the NAND partitioning scheme in DTS eliminating gap between
consecutive partitions
+ Fix 10Gb ports PHY mode names
- Extend PCIe MEM space on Armada 37xx: useful for some combination
of PCIe cards where the initial 16MB was not enough
* tag 'mvebu-dt64-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: marvell: armada-37xx: Extend PCIe MEM space
arch/arm64: dts: change 10gbase-kr to 10gbase-r in Armada
arm64: dts: add support for Marvell cn9130-crb platform
dts: marvell: Enable 10G interfaces on 9130-DB and 9131-DB boards
arm64: dts: cn913x: add device trees for topology B boards
Arnd Bergmann [Wed, 18 Aug 2021 12:37:16 +0000 (14:37 +0200)]
Merge tag 'qcom-arm64-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 updates for v5.15
SDM660 and SDM630 was concluded to be similar enough that they should be
merged, and the derivative SDM636 was added to the bunch. The combined
platform gained support for GPU, DMA, I2C, IMEM, display, power-domains,
SDHCI, thermal, USB, interconnects, VADC, WLED and audio remoteproc. The
Sony Xperia "Ganges" platform was similarly merged with "Nile", got
cleaned up and gained touchscreen, USB, volume keys and uSD support.
IPQ6018 gains USB2 and PCIe support and a few minor fixes. IPQ8074
gains SCM, PRNG and Crypto support and a DT style update of the PCIe
nodes.
MSM8916 gains Coresight STM support. The Xiaomi Redmi 2 is introduced,
with touchscreen, notification LED and IMU support. MSM8996 gains
support for GPU cooling and v3.0 of the SoC, which is used to introduce
support for the Sony Xperia X Performance, XZ and XZs phones.
SC7180 finally gains DisplayPort support and LPASS is updated
accordingly. A number of fixes are introduced and with the newly
introduced DRM aux bus in place Trogdor's panel is moved under the eDP
bridge. SC7280 gained USB, eMMC, SD-card, QFPROM and IPA support, the
new IDP2 board was added.
SM6126 (aka Snapdragon 665) was introduced, together with the Sony
Xperia 10II phone with support for framebuffer, USB, eMMC and volume
keys.
SM8150 gained inline crypto support for UFS enabled, CPU opp-tables was
introduced to scale DDR and L3 frequencies and SPI nodes where added, in
addition to a number of smaller fixes.
SM8250 gained a number of minor fixes and had its serial engines wired
up to use the GENI wrappers' DMA engines.
SM8350 had wakeup-parent defined for the TLMM gpio node and I2C13 was
introduced.
SDM845 display clocks was corrected and Lenovo Yoga C630 got IPA enabled
and now has working LTE connectivity.
Additionally a number of minor fixes throughout to correct DT validation
warnings.
Lastly v5.14-rc3 is merge in to resolve the merge conflicts caused by
the USB maintainer deciding to fix a regression in his tree.
Pali Rohár [Thu, 24 Jun 2021 21:55:46 +0000 (23:55 +0200)]
arm64: dts: marvell: armada-37xx: Extend PCIe MEM space
Current PCIe MEM space of size 16 MB is not enough for some combination
of PCIe cards (e.g. NVMe disk together with ath11k wifi card). ARM Trusted
Firmware for Armada 3700 platform already assigns 128 MB for PCIe window,
so extend PCIe MEM space to the end of 128 MB PCIe window which allows to
allocate more PCIe BARs for more PCIe cards.
Without this change some combination of PCIe cards cannot be used and
kernel show error messages in dmesg during initialization:
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01800000]
pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x01800000]
pci 0000:00:00.0: BAR 6: assigned [mem 0xe8000000-0xe80007ff pref]
pci 0000:01:00.0: BAR 8: no space for [mem size 0x01800000]
pci 0000:01:00.0: BAR 8: failed to assign [mem size 0x01800000]
pci 0000:02:03.0: BAR 8: no space for [mem size 0x01000000]
pci 0000:02:03.0: BAR 8: failed to assign [mem size 0x01000000]
pci 0000:02:07.0: BAR 8: no space for [mem size 0x00100000]
pci 0000:02:07.0: BAR 8: failed to assign [mem size 0x00100000]
pci 0000:03:00.0: BAR 0: no space for [mem size 0x01000000 64bit]
pci 0000:03:00.0: BAR 0: failed to assign [mem size 0x01000000 64bit]
Due to bugs in U-Boot port for Turris Mox, the second range in Turris Mox
kernel DTS file for PCIe must start at 16 MB offset. Otherwise U-Boot
crashes during loading of kernel DTB file. This bug is present only in
U-Boot code for Turris Mox and therefore other Armada 3700 devices are not
affected by this bug. Bug is fixed in U-Boot version 2021.07.
To not break booting new kernels on existing versions of U-Boot on Turris
Mox, use first 16 MB range for IO and second range with rest of PCIe window
for MEM.
Signed-off-by: Pali Rohár <pali@kernel.org> Fixes: 76f6386b25cc ("arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700") Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Arnd Bergmann [Tue, 17 Aug 2021 09:30:40 +0000 (11:30 +0200)]
Merge tag 'qcom-dts-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm dts updates for v5.15
This introduces the MSM8226 platform and an initial dts for the Samsung
Galaxy S III Neo phone.
MSM8974 gains another UART and this is used to enable Bluetooth on the
Sony Xperia Z2 Tablet. Samsung Galaxy S5 gains regulator definitions for
audio and modem remoteprocs, effectively enabling these.
DSI clocks on APQ8064 are updates as the old legacy clock names are no
longer supported by the driver. And IPQ806x GMAC nodes gains AHB resets
wired up.
Lastly APQ8060 is converted to a SPDX header and the ethernet node is
updates in accordance with the binding.
* tag 'qcom-dts-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: add ahb reset to ipq806x-gmac
ARM: dts: qcom: Fix up APQ8060 DragonBoard license
ARM: dts: qcom: msm8974: castor: Add Bluetooth-related nodes
ARM: dts: qcom: msm8974: Add blsp2_uart7 for bluetooth on sirius
ARM: dts: qcom: Add initial DTS file for Samsung Galaxy S III Neo phone
dt-bindings: arm: qcom: Document MSM8226 SoC binding
ARM: dts: qcom: Add support for MSM8226 SoC
ARM: dts: qcom: apq8060: Correct Ethernet node name and drop bogus irq property
ARM: dts: qcom: apq8064: correct clock names
ARM: dts: qcom: msm8974-klte: Enable remote processors
Jim Wright [Mon, 16 Aug 2021 16:00:02 +0000 (11:00 -0500)]
ARM: dts: aspeed: p10bmc: Add power control pins
Add to p10bmc systems the GPIO line names used in chassis power on / off
control and chassis power good monitoring. Names used are as documented at [1].
Bjorn Andersson [Mon, 16 Aug 2021 23:02:26 +0000 (18:02 -0500)]
Merge tag 'v5.14-rc3' into arm64-for-5.15
The USB maintainer felt the strong need to push '1f958f3dff42
("Revert "arm64: dts: qcom: Harmonize DWC USB3 DT nodes name"")'
through the usb tree, so merge v5.14-rc3 to resolve the resulting merge
conflicts.
Arnd Bergmann [Mon, 16 Aug 2021 21:17:16 +0000 (23:17 +0200)]
Merge tag 'imx-dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm32 device tree changes for 5.15:
- A series from Christoph Niedermaier to clean up i.MX6 DHCOM support.
- New board support: DHCOM based PicoITX, DHSOM based DRC02, SolidRun
SolidSense, SKOV i.MX6 boards.
- Add WiFi support for i.MX7D base reMkarkable2 device.
- Add FTM devices for i.MX7 to have Flex Timers support.
- Configure ENET_REF clock to 125MHz for imx6qp-prtwd3 to support RGMII
PHY mode.
- Drop unneeded #address-cells and #size-cells from vf610-zii SPI EEPROM
device node.
- Add missing USB OTG OC pinmux and Crypto device for i.MX6QDL Gateworks
boards.
* tag 'imx-dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (23 commits)
ARM: dts: imx6qp-prtwd3: configure ENET_REF clock to 125MHz
ARM: dts: vf610-zii-dev-rev-b: Remove #address-cells and #size-cells property from at93c46d dt node
ARM: dts: add SKOV imx6q and imx6dl based boards
ARM: dts: imx7: add ftm nodes for Flex Timers
ARM: dts: imx6qdl-dhcom: Add DHSOM based DRC02 board
ARM: dts: imx6qdl-dhcom: Add DHCOM based PicoITX board
ARM: dts: imx6qdl-dhcom: Split SoC-independent parts of DHCOM SOM and PDK2
ARM: dts: imx6q-dhcom: Cleanup of the devicetrees
ARM: dts: imx6q-dhcom: Rearrange of iomux
ARM: dts: imx6q-dhcom: Rework of the DHCOM GPIO pinctrls
ARM: dts: imx6q-dhcom: Use 1G ethernet on the PDK2 board
ARM: dts: imx6q-dhcom: Set minimum memory size of all DHCOM i.MX6 variants
ARM: dts: imx6q-dhcom: Remove ddc-i2c-bus property
ARM: dts: imx6q-dhcom: Add keys and leds to the PDK2 board
ARM: dts: imx6q-dhcom: Align stdout-path with other DHCOM SoMs
ARM: dts: imx6q-dhcom: Adding Wake pin to the PCIe pinctrl
ARM: dts: imx6q-dhcom: Fill GPIO line names on DHCOM SoM
ARM: dts: imx6q-dhcom: Add interrupt and compatible to the ethernet PHY
ARM: dts: imx6q-dhcom: Add the parallel system bus
ARM: dts: imx7d-remarkable2: Add WiFi support
...
Arnd Bergmann [Mon, 16 Aug 2021 21:09:45 +0000 (23:09 +0200)]
Merge tag 'imx-dt64-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree changes for 5.15:
- New board support: Nitrogen8 SoM and MNT Reform2, LS1088A based
Traverse Ten64, i.MX8M based GW7902.
- A series from Ioana Ciornei to update PHY IRQ configuration for
LayerScape SoCs.
- A series from Tim Harvey to update Gateworks imx8mm-venice devices.
- Replace deprecated `fsl,usbphy` property with phys phandle.
- Add MIPI CSI phy and bridge descriptions for i.MX8MQ SoC.
- Add JPEG encoder/decoder device nodes for i.MX8M SoCs.
- Update PMU compatible and drop interrupt-affinity for i.MX8M SoCs.
- Add Cadence HIFI4 DSP for i.MX8 MPlus SoC.
- A few small and random updates on various boards.
* tag 'imx-dt64-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (27 commits)
arm64: dts: add device tree for Traverse Ten64 (LS1088A)
arm64: dts: ls1088a: add missing PMU node
arm64: dts: ls1088a: add internal PCS for DPMAC1 node
arm64: dts: imx8mq-reform2: add sound support
arm64: dts: imx8m: drop interrupt-affinity for pmu
arm64: dts: imx8qxp: update pmu compatible
arm64: dts: imx8mm: update pmu compatible
arm64: dts: ls1046a: fix eeprom entries
arm64: dts: imx8mm-venice-gw7901: enable pull-down on gpio outputs
arm64: dts: imx8mm-venice-gw7901: add support for USB hub subload
arm64: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
arm64: dts: imx8mm-venice-gw700x: fix invalid pmic pin config
arm64: dts: imx8mm-venice-gw700x: fix mp5416 pmic config
arm64: dts: imx8mq: add mipi csi phy and csi bridge descriptions
arm64: dts: imx: Add i.mx8mm/imx8mn Gateworks gw7902 dts support
arm64: dts: imx8mp: Add dsp node
arm64: dts: imx8m: Replace deprecated fsl,usbphy DT props with phys
arm64: dts: imx8mq-evk: Remove unnecessary blank lines
arm64: dts: imx8mq-evk: add CD pinctrl for usdhc2
arm64: dts: imx8mm-venice-gw7901: Remove unnecessary #address-cells/#size-cells
...
Arnd Bergmann [Mon, 16 Aug 2021 21:00:02 +0000 (23:00 +0200)]
Merge tag 'tegra-for-5.15-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.15-rc1
Contains a couple of fixes across the board and adds support for the
recently released NVIDIA Jetson TX2 NX Developer Kit.
* tag 'tegra-for-5.15-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix compatible string for Tegra132 CPUs
arm64: tegra: Add missing interconnects property for USB on Tegra186
arm64: tegra: Add NVIDIA Jetson TX2 NX Developer Kit support
arm64: tegra: Add PWM nodes on Tegra186
arm64: tegra194: p2888: Correct interrupt trigger type of temperature sensor
arm64: tegra: Fix Tegra194 PCIe EP compatible string
Arnd Bergmann [Mon, 16 Aug 2021 20:58:39 +0000 (22:58 +0200)]
Merge tag 'tegra-for-5.15-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.15-rc1
The majority of this is temperature sensor additions for various devices
and fixes to the trigger type of the thermal interrupts.
Other than that there are various minor fixes across the board.
* tag 'tegra-for-5.15-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: tamonten: Fix UART pad setting
ARM: tegra: nexus7: Improve thermal zones
ARM: tegra: acer-a500: Improve thermal zones
ARM: tegra: acer-a500: Use verbose variant of atmel,wakeup-method value
ARM: tegra: acer-a500: Add power supplies to accelerometer
ARM: tegra: acer-a500: Remove bogus USB VBUS regulators
ARM: tegra: jetson-tk1: Correct interrupt trigger type of temperature sensor
ARM: tegra: dalmore: Correct interrupt trigger type of temperature sensor
ARM: tegra: cardhu: Correct interrupt trigger type of temperature sensor
ARM: tegra: apalis: Correct interrupt trigger type of temperature sensor
ARM: tegra: nyan: Correct interrupt trigger type of temperature sensor
ARM: tegra: acer-a500: Add interrupt to temperature sensor node
ARM: tegra: nexus7: Add interrupt to temperature sensor node
ARM: tegra: paz00: Add interrupt to temperature sensor node
ARM: tegra: ouya: Add interrupt to temperature sensor node
ARM: tegra: Add SoC thermal sensor to Tegra30 device-trees
Mathew McBride [Tue, 10 Aug 2021 05:38:28 +0000 (05:38 +0000)]
arm64: dts: add device tree for Traverse Ten64 (LS1088A)
The Traverse Technologies Ten64 is a Mini-ITX form factor
networking board using the NXP LS1088A SoC.
This device tree only describes features which the mainline
kernel currently has support for, such as some I2C-connected
devices that are not described at present.
System documentation may be found at ten64doc.traverse.com.au
Signed-off-by: Mathew McBride <matt@traverse.com.au> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> # for the MAC/PHY Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mathew McBride [Tue, 10 Aug 2021 05:38:25 +0000 (05:38 +0000)]
arm64: dts: ls1088a: add missing PMU node
The Performance Manager Unit was not described in the DTS
which meant performance event monitoring was not possible.
This was exposed by a change to the PMU handling in KVM
in 5.11-rc3 which now prevents a PMU being exposed to a
guest when the host does not provide one:
"KVM: arm64: Don't access PMCR_EL0 when no PMU is available"
Lucas Stach [Thu, 12 Aug 2021 19:47:12 +0000 (21:47 +0200)]
arm64: dts: imx8mq-reform2: add sound support
This adds sound support to the Reform2.
It differs from the downstream implementation in that the codec
is used as the BCLK and FSYNC master and the i.MX8MQ only supplies
a fixed 25MHz MCLK from the oscillator. This allows to support
a wider range of audio rates by using the codec PLL and to shut
down the audio PLLs on the i.MX8MQ SoC side.
Raag Jadav [Wed, 4 Aug 2021 19:24:45 +0000 (00:54 +0530)]
arm64: dts: ls1046a: fix eeprom entries
ls1046afrwy and ls1046ardb boards have CAT24C04[1] and CAT24C05[2]
eeproms respectively. Both are 4Kb (512 bytes) in size,
and compatible with AT24C04[3].
Remove multi-address entries, as both the boards have a single chip each.
Tim Harvey [Tue, 27 Jul 2021 16:11:00 +0000 (09:11 -0700)]
arm64: dts: imx8mm-venice-gw7901: add support for USB hub subload
The USB hub has it's reset as GPIO4_IO17 but can be sub-loaded and
VBUS provided by a VBUS regulator with GPIO4_IO2 as the enable and
GPIO1_IO15 as the active-low over-current.
Enable pull-up for GPIO4_IO17 to keep hub out of reset and move VBUS
enable to GPIO4_IO2. Additionally enable pull-up on GPIO1_IO15 so that
if the hub is loaded it never over-currents.
This allows USB to work in both configurations without a device-tree
change.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Tue, 27 Jul 2021 16:10:59 +0000 (09:10 -0700)]
arm64: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12
is the power-enable to the TPS25821 Source controller and power switch
responsible for monitoring the CC pins and enabling VBUS. Therefore
GPIO1_12 must always be enabled and the vbus output enable from the
IMX8MM can be ignored.
To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the
TPS25821 and change the regulator output to GPIO1_10 which is
unconnected.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the 2 available CSI interfaces on the i.MX8MQ with the MIPI-CSI2
receiver (new driver) and the CSI Bridge that provides the user buffers
(existing driver).
An image sensor is to be connected to the MIPIs' second port, to be described
in board files.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Fri, 23 Jul 2021 18:41:16 +0000 (11:41 -0700)]
arm64: dts: imx: Add i.mx8mm/imx8mn Gateworks gw7902 dts support
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Daniel Baluta [Fri, 23 Jul 2021 11:05:40 +0000 (14:05 +0300)]
arm64: dts: imx8mp: Add dsp node
i.MX8 MPlus SoC integrates Cadence HIFI4 DSP. This core runs either a
custom firmware or the open source SOF firmware [1]
DSP device is handled by SOF OF driver found in
sound/soc/sof/sof-of-dev.c
Notice that the DSP node makes use of:
- dsp_reserved, a reserved memory region for various Audio
resources (e.g firmware loading, audio buffers, etc).
- Messaging Unit (mu2) for passing notifications betweem ARM
core and DSP.
[1] https://thesofproject.github.io/latest/platforms/index.html Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Thierry Reding [Tue, 22 Jun 2021 13:44:22 +0000 (15:44 +0200)]
arm64: tegra: Fix compatible string for Tegra132 CPUs
The documented compatible string for the CPUs found on Tegra132 is
"nvidia,tegra132-denver", rather than the previously used compatible
string "nvidia,denver".
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:47 +0000 (00:19 +0300)]
ARM: tegra: nexus7: Improve thermal zones
Use skin temperature for maintaining temperature that is suitable
specifically for Nexus 7. Add CPU thermal zone that protects silicon.
All these changes don't make a significant difference, but it is a
more correct definition of thermal zones.
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:46 +0000 (00:19 +0300)]
ARM: tegra: acer-a500: Improve thermal zones
Use skin temperature for maintaining temperature that is suitable
specifically for A500. Add CPU thermal zone that protects silicon.
All these changes don't make a significant difference, but it is a
more correct definition of thermal zones.
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:45 +0000 (00:19 +0300)]
ARM: tegra: acer-a500: Use verbose variant of atmel,wakeup-method value
The verbose variant of the atmel,wakeup-method value was lost when patch
that added the property was merged because it conflicted with other patch,
re-add it for consistency.
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:43 +0000 (00:19 +0300)]
ARM: tegra: acer-a500: Remove bogus USB VBUS regulators
The configuration of USB VBUS regulators was borrowed from downstream
kernel, which is incorrect because the corresponding GPIOs are connected
to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board
schematics. USB works fine with both GPIOs being disabled, so remove the
bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed
5v system regulator and device-mode USB1 doesn't have VBUS switches.
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:42 +0000 (00:19 +0300)]
ARM: tegra: jetson-tk1: Correct interrupt trigger type of temperature sensor
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:41 +0000 (00:19 +0300)]
ARM: tegra: dalmore: Correct interrupt trigger type of temperature sensor
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:40 +0000 (00:19 +0300)]
ARM: tegra: cardhu: Correct interrupt trigger type of temperature sensor
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:39 +0000 (00:19 +0300)]
ARM: tegra: apalis: Correct interrupt trigger type of temperature sensor
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:38 +0000 (00:19 +0300)]
ARM: tegra: nyan: Correct interrupt trigger type of temperature sensor
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:34 +0000 (00:19 +0300)]
ARM: tegra: ouya: Add interrupt to temperature sensor node
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor and enable it in pinmux,
for completeness.
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:33 +0000 (00:19 +0300)]
ARM: tegra: Add SoC thermal sensor to Tegra30 device-trees
Add the on-chip SoC thermal sensor to Tegra30 device-trees. Now CPU
temperature reporting and thermal throttling is available on all Tegra30
devices universally.
Tao Ren [Thu, 5 Aug 2021 22:28:15 +0000 (15:28 -0700)]
ARM: dts: aspeed: Common dtsi for Facebook AST2600 Network BMCs
This common descirption is included by all Facebook AST2600 Network BMC
platforms to minimize duplicated device entries across Facebook Network
BMC device trees.
Arnd Bergmann [Thu, 12 Aug 2021 20:56:26 +0000 (22:56 +0200)]
Merge tag 'omap-for-v5.15/dt-am3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Changes for am3 cpsw and SanCloud for v5.15
A series of changes to update am3 to use cpsw switch driver and
few updates to earlier SanCloud changes. The plan was to send the
cpsw switch driver changes earlier but looks like I never tagged
the mail thread in my inbox to apply for v5.15.
* tag 'omap-for-v5.15/dt-am3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-sancloud-bbe: Drop usb wifi comment
ARM: dts: am335x-sancloud-bbe: Fix missing pinctrl refs
ARM: dts: am335x-bone: switch to new cpsw switch drv
ARM: dts: am33xx: update ethernet aliases
ARM: dts: am335x-sl50: switch to new cpsw switch drv
ARM: dts: am335x-shc: switch to new cpsw switch drv
ARM: dts: am335x-phycore: switch to new cpsw switch drv
ARM: dts: am335x-pepper: switch to new cpsw switch drv
ARM: dts: am335x-pdu001: switch to new cpsw switch drv
ARM: dts: am335x-osd3358-sm-red: switch to new cpsw switch drv
ARM: dts: am335x-myirtech: switch to new cpsw switch drv
ARM: dts: am335x-moxa-uc: switch to new cpsw switch drv
ARM: dts: am335x-lxm: switch to new cpsw switch drv
ARM: dts: am335x-igep0033: switch to new cpsw switch drv
ARM: dts: am335x-cm-t335: switch to new cpsw switch drv
ARM: dts: am335x-chiliboard: switch to new cpsw switch drv
ARM: dts: am335x-nano: switch to new cpsw switch drv
ARM: dts: am335x-baltos: switch to new cpsw switch drv
Arnd Bergmann [Thu, 12 Aug 2021 20:55:50 +0000 (22:55 +0200)]
Merge tag 'samsung-dt64-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v5.15
1. Add CPU topology and cache information to Exynos DTSI files.
2. Correct GIC CPU interfaces address range on Exynos7.
* tag 'samsung-dt64-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: correct GIC CPU interfaces address range on Exynos7
arm64: dts: exynos: add CPU topology to Exynos5433
arm64: dts: exynos: Add cpu cache information to Exynos5433
arm64: dts: exynos: Add cpu cache information to Exynos7
Arnd Bergmann [Thu, 12 Aug 2021 20:55:17 +0000 (22:55 +0200)]
Merge tag 'samsung-dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.15
Add CPU topology to all Exynos DTSI files.
* tag 'samsung-dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: add CPU topology to Exynos5422
ARM: dts: exynos: add CPU topology to Exynos5420
ARM: dts: exynos: add CPU topology to Exynos5260
ARM: dts: exynos: add CPU topology to Exynos5250
ARM: dts: exynos: add CPU topology to Exynos4412
ARM: dts: exynos: add CPU topology to Exynos4210
ARM: dts: exynos: add CPU topology to Exynos3250
Arnd Bergmann [Thu, 12 Aug 2021 20:54:50 +0000 (22:54 +0200)]
Merge tag 'amlogic-arm-dt-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/dt
Amlogic ARM DT changes for v5.15:
- meson8: use a default higher default GPU clock to solve probe failure
- meson: add AIU audio controller and codec for ec100
- meson8b: fix pwm regulator supply property name
* tag 'amlogic-arm-dt-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
ARM: dts: meson8b: ec100: Fix the pwm regulator supply properties
ARM: dts: meson8b: mxq: Fix the pwm regulator supply properties
ARM: dts: meson8b: odroidc1: Fix the pwm regulator supply properties
ARM: dts: meson8b: ec100: wire up the RT5640 audio codec
ARM: dts: meson: Add the AIU audio controller
ARM: dts: meson8: Use a higher default GPU clock frequency
Arnd Bergmann [Thu, 12 Aug 2021 20:49:21 +0000 (22:49 +0200)]
Merge tag 'stm32-dt-for-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT for v5.15, round 1
Highlights:
----------
-MPU:
- ST boards:
- Add coporcessor detach mailbox on ED and DKx boards
- Fix dtbs_check SAI warnings
- DH boards:
-Fix some dtbs_check warnings: usb, backlight, hdmi
* tag 'stm32-dt-for-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Update AV96 adv7513 node per dtbs_check
ARM: dts: stm32: Set {bitclock,frame}-master phandles on ST DKx
ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards
ARM: dts: stm32: Add coprocessor detach mbox on stm32mp157c-ed1 board
ARM: dts: stm32: Add usbphyc_port1 supply on DHCOM SoM
ARM: dts: stm32: Add backlight and panel supply on DHCOM SoM
ARM: dts: stm32: Set {bitclock,frame}-master phandles on DHCOM SoM
ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM
ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM
ARM: dts: stm32: Prefer HW RTC on DHCOM SoM
Thierry Reding [Thu, 12 Aug 2021 14:17:12 +0000 (16:17 +0200)]
arm64: tegra: Add missing interconnects property for USB on Tegra186
The device tree node for the XUDC (USB device mode controller) is
missing the interconnects property that describes the path to memory for
the controller. Add the property so that the things like the DMA mask
can be set by the operating system.
Thierry Reding [Thu, 12 Aug 2021 12:26:16 +0000 (14:26 +0200)]
arm64: tegra: Add PWM nodes on Tegra186
These PWMs can be used for fan or LED backlight control. Add the device
tree nodes for all existing controllers found on Tegra186 SoCs. None of
these are enabled by default, which is left for the board DTS files to
do when necessary.
The Renesas RZ/A and RZ/G2L I2C Bus Interface has no less than 8
interrupts. Hence document the "interrupt-names" property, to make it
easier to review the interrupt mappings in DTS files.
Note that this property cannot be made required yet, as the RIIC nodes
in all DTS files lack the property.
arm64: tegra194: p2888: Correct interrupt trigger type of temperature sensor
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
projects / thirdparty / kernel / stable.git / log
