Linus Walleij [Wed, 10 Oct 2018 18:39:18 +0000 (20:39 +0200)]
pinctrl: gemini: Fix up TVC clock group
The previous fix made the TVC clock get muxed in on the
D-Link DIR-685 instead of giving nagging warnings of this
not working. Not good. We didn't want that, as it breaks
video.
Create a specific group for the TVC CLK, and break out
a specific GPIO group for it on the SL3516 so we can use
that line as GPIO if we don't need the TVC CLK.
Fixes: d17f477c5bc6 ("pinctrl: gemini: Mask and set properly") Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 9 Oct 2018 08:11:53 +0000 (10:11 +0200)]
pinctrl: gemini: Mask and set properly
The code was written under the assumption that the
regmap_update_bits() would mask the bits in the mask and
set the bits in the value.
It missed the points that it will not set bits in the value
unless these are also masked in the mask. Set value bits
that are not in the mask will simply be ignored.
Arnd Bergmann [Mon, 8 Oct 2018 15:57:43 +0000 (17:57 +0200)]
pinctrl: mediatek: select GPIOLIB
Removing the linux/gpio.h include means we no longer have a declaration
of gpiochip_lock_as_irq() when CONFIG_GPIOLIB is disabled:
drivers/pinctrl/mediatek/mtk-eint.c: In function 'mtk_eint_irq_request_resources':
drivers/pinctrl/mediatek/mtk-eint.c:247:8: error: implicit declaration of function 'gpiochip_lock_as_irq'; did you mean 'spin_lock_irq'? [-Werror=implicit-function-declaration]
drivers/pinctrl/mediatek/mtk-eint.c: In function 'mtk_eint_irq_release_resources':
drivers/pinctrl/mediatek/mtk-eint.c:272:2: error: implicit declaration of function 'gpiochip_unlock_as_irq'; did you mean 'spin_unlock_irq'? [-Werror=implicit-function-declaration]
Sean Wang [Thu, 4 Oct 2018 11:40:38 +0000 (19:40 +0800)]
MAINTAINERS: update entry for Mediatek pin controller
Add all source files under drivers/pinctrl/mediatek for the entry and
change the address to a permanent one since I have a personal leave
over the next few months and the address would be suspended for a while.
Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Northstar has mux controller just like Northstar Plus and Northstar2.
It's a bit different though (different registers & pins) so it requires
its own binding.
It's needed to allow other block bindings specify required mux setup.
Andy Shevchenko [Wed, 26 Sep 2018 14:43:17 +0000 (17:43 +0300)]
pinctrl: intel: Fix a spelling typo in kernel documentation
The parameter 'community' had been spelled incorrectly.
Fix it here.
As a side effect it satisfies static checkers that issue
the following warnings:
drivers/pinctrl/intel/pinctrl-intel.c:845: warning: Function parameter or member 'community' not described in 'intel_gpio_to_pin'
drivers/pinctrl/intel/pinctrl-intel.c:845: warning: Excess function parameter 'commmunity' description in 'intel_gpio_to_pin'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Stephen Boyd [Mon, 1 Oct 2018 21:49:05 +0000 (14:49 -0700)]
pinctrl: msm: Actually use function 0 for gpio selection
This code needs to select function #0, which is the first int in the
array of functions, not the number 0 which may or may not be the
function for "GPIO mode" per the enum mapping. We were getting lucky on
SDM845, where this was tested, because the function 0 matched the enum
value for "GPIO mode". On other platforms, e.g. MSM8996, the gpio enum
value is the last one in the list so this code doesn't work and we see a
warning at boot. Fix it by grabbing the first element out of the array
of functions.
Cc: Doug Anderson <dianders@chromium.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Niklas Cassel <niklas.cassel@linaro.org> Reported-by: Niklas Cassel <niklas.cassel@linaro.org> Fixes: 1de7ddb3a15c ("pinctrl: msm: Mux out gpio function with gpio_request()") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Tested-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Yanjiang Jin [Sat, 29 Sep 2018 09:06:55 +0000 (17:06 +0800)]
pinctrl: core: make sure strcmp() doesn't get a null parameter
Some drivers, for example, QCOM's qdf2xxx, set groups[gpio].name only
when gpio is valid, and leave invalid gpio names as null.
If we want to access the sys node "pinconf-groups",
pinctrl_get_group_selector() -> get_group_name() may return a null
pointer if group_selector is invalid, then the below Kernel panic
would happen since strcmp() uses this null pointer to do comparison.
Unable to handle kernel NULL pointer dereference at ss 00000000
el:Internal error: Oops: 9600000[ 143.080279]
SMP
CPU: 19 PID: 2493 Comm: read_all Tainted: G O
.aarch64 #1
Hardware name: HXT Semiconductor HXT REP-2 System
PC is at strcmp+0x18/0x154
LR is at pinctrl_get_group_selector+0x6c/0xe8
Process read_all (pid: 2493, stack limit =
Call trace:
Exception stack
strcmp+0x18/0x154
pin_config_group_get+0x64/0xd8
pinconf_generic_dump_one+0xd8/0x1c0
pinconf_generic_dump_pins+0x94/0xc8
pinconf_groups_show+0xb4/0x104
seq_read+0x178/0x464
full_proxy_read+0x6c/0xac
__vfs_read+0x58/0x178
vfs_read+0x94/0x164
SyS_read+0x60/0xc0
__sys_trace_return+0x0/0x4
--[ end trace]--
Kernel panic - not syncing: Fatal exception
Signed-off-by: Yanjiang Jin <yanjiang.jin@hxt-semitech.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Mon, 1 Oct 2018 11:21:58 +0000 (13:21 +0200)]
Merge tag 'sh-pfc-for-v4.20-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.20 (take two)
- Add MSIOF pin groups on R-Car E3 and D3,
- Add support for the new RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs,
- Add I2C4, DU0, QSPI0, SDHI2, and USB pin groups on RZ/G1C,
- Convert to SPDX license identifiers,
- Small cleanups.
Linus Walleij [Mon, 1 Oct 2018 11:20:45 +0000 (13:20 +0200)]
Merge tag 'v4.19-rc6' into devel
This is the 4.19-rc6 release
I needed to merge this in because of extensive conflicts in
the MSM and Intel pin control drivers. I know how to resolve
them, so let's do it like this.
Merge tag 'for-linus-20180929' of git://git.kernel.dk/linux-block
Jens writes:
"Block fixes for 4.19-rc6
A set of fixes that should go into this release. This pull request
contains:
- A fix (hopefully) for the persistent grants for xen-blkfront. A
previous fix from this series wasn't complete, hence reverted, and
this one should hopefully be it. (Boris Ostrovsky)
- Fix for an elevator drain warning with SMR devices, which is
triggered when you switch schedulers (Damien)
- bcache deadlock fix (Guoju Fang)
- Fix for the block unplug tracepoint, which has had the
timer/explicit flag reverted since 4.11 (Ilya)
- Fix a regression in this series where the blk-mq timeout hook is
invoked with the RCU read lock held, hence preventing it from
blocking (Keith)
- NVMe pull from Christoph, with a single multipath fix (Susobhan Dey)"
* tag 'for-linus-20180929' of git://git.kernel.dk/linux-block:
xen/blkfront: correct purging of persistent grants
Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
blk-mq: I/O and timer unplugs are inverted in blktrace
bcache: add separate workqueue for journal_write to avoid deadlock
xen/blkfront: When purging persistent grants, keep them in the buffer
block: fix deadline elevator drain for zoned block devices
blk-mq: Allow blocking queue tag iter callbacks
nvme: properly propagate errors in nvme_mpath_init
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Thomas writes:
"A single fix for the AMD memory encryption boot code so it does not
read random garbage instead of the cached encryption bit when a kexec
kernel is allocated above the 32bit address limit."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Fix kexec booting failure in the SEV bit detection code
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Thomas writes:
"Three small fixes for clocksource drivers:
- Proper error handling in the Atmel PIT driver
- Add CLOCK_SOURCE_SUSPEND_NONSTOP for TI SoCs so suspend works again
- Fix the next event function for Facebook Backpack-CMM BMC chips so
usleep(100) doesnt sleep several milliseconds"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/timer-atmel-pit: Properly handle error cases
clocksource/drivers/fttmr010: Fix set_next_event handler
clocksource/drivers/ti-32k: Add CLOCK_SOURCE_SUSPEND_NONSTOP flag for non-am43 SoCs
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Thomas writes:
"A single fix for a missing sanity check when a pinned event is tried
to be read on the wrong CPU due to a legit event scheduling failure."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Add sanity check to deal with pinned event failure
There is currently a warning when building the Kryo cpufreq driver into
the kernel image:
WARNING: vmlinux.o(.text+0x8aa424): Section mismatch in reference from
the function qcom_cpufreq_kryo_probe() to the function
.init.text:qcom_cpufreq_kryo_get_msm_id()
The function qcom_cpufreq_kryo_probe() references
the function __init qcom_cpufreq_kryo_get_msm_id().
This is often because qcom_cpufreq_kryo_probe lacks a __init
annotation or the annotation of qcom_cpufreq_kryo_get_msm_id is wrong.
Remove the '__init' annotation from qcom_cpufreq_kryo_get_msm_id
so that there is no more mismatch warning.
Additionally, Nick noticed that the remove function was marked as
'__init' when it should really be marked as '__exit'.
Fixes: 46e2856b8e18 (cpufreq: Add Kryo CPU scaling driver) Fixes: 5ad7346b4ae2 (cpufreq: kryo: Add module remove and exit) Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: 4.18+ <stable@vger.kernel.org> # 4.18+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Dmitry writes:
"Input updates for v4.19-rc5
Just a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - allow for max == min during input_absinfo validation
Input: elantech - enable middle button of touchpad on ThinkPad P72
Input: atakbd - fix Atari CapsLock behaviour
Input: atakbd - fix Atari keymap
Input: egalax_ts - add system wakeup support
Input: gpio-keys - fix a documentation index issue
Merge tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark writes:
"spi: Fixes for v4.19
Quite a few fixes for the Renesas drivers in here, plus a fix for the
Tegra driver and some documentation fixes for the recently added
spi-mem code. The Tegra fix is relatively large but fairly
straightforward and mechanical, it runs on probe so it's been
reasonably well covered in -next testing."
* tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-mem: Move the DMA-able constraint doc to the kerneldoc header
spi: spi-mem: Add missing description for data.nbytes field
spi: rspi: Fix interrupted DMA transfers
spi: rspi: Fix invalid SPI use during system suspend
spi: sh-msiof: Fix handling of write value for SISTR register
spi: sh-msiof: Fix invalid SPI use during system suspend
spi: gpio: Fix copy-and-paste error
spi: tegra20-slink: explicitly enable/disable clock
Merge tag 'regulator-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Mark writes:
"regulator: Fixes for 4.19
A collection of fairly minor bug fixes here, a couple of driver
specific ones plus two core fixes. There's one fix for the new
suspend state code which fixes some confusion with constant values
that are supposed to indicate noop operation and another fixing a
race condition with the creation of sysfs files on new regulators."
* tag 'regulator-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fix crash caused by null driver data
regulator: Fix 'do-nothing' value for regulators without suspend state
regulator: da9063: fix DT probing with constraints
regulator: bd71837: Disable voltage monitoring for LDO3/4
Merge tag 'pinctrl-v4.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Linus writes:
"Pin control fixes for v4.19:
- Fixes to x86 hardware:
- AMD interrupt debounce issues
- Faulty Intel cannonlake register offset
- Revert pin translation IRQ locking"
* tag 'pinctrl-v4.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
Revert "pinctrl: intel: Do pin translation when lock IRQ"
pinctrl: cannonlake: Fix HOSTSW_OWN register offset of H variant
pinctrl/amd: poll InterruptEnable bits in amd_gpio_irq_set_type
perf/core: Add sanity check to deal with pinned event failure
It is possible that a failure can occur during the scheduling of a
pinned event. The initial portion of perf_event_read_local() contains
the various error checks an event should pass before it can be
considered valid. Ensure that the potential scheduling failure
of a pinned event is checked for and have a credible error.
* tag 'drm-fixes-2018-09-28' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Fix Edid emulation for linux
drm/amd/display: Fix Vega10 lightup on S3 resume
drm/amdgpu: Fix vce work queue was not cancelled when suspend
Revert "drm/panel: Add device_link from panel device to DRM device"
drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
drm/malidp: Fix writeback in NV12
drm: mali-dp: Call drm_crtc_vblank_reset on device init
drm/etnaviv: add DMA configuration for etnaviv platform device
Merge tag 'riscv-for-linus-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Palmer writes:
"A Single RISC-V Update for 4.19-rc6
The Debian guys have been pushing on our port and found some
unversioned symbols leaking into modules. This PR contains a single
fix for that issue."
* tag 'riscv-for-linus-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISC-V: include linux/ftrace.h in asm-prototypes.h
* tag 'pci-v4.19-fixes-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
PCI: dwc: Fix scheduling while atomic issues
MAINTAINERS: Move mobiveil PCI driver entry where it belongs
MAINTAINERS: Update PPC contacts for PCI core error handling
xen/blkfront: correct purging of persistent grants
Commit a46b53672b2c2e3770b38a4abf90d16364d2584b ("xen/blkfront: cleanup
stale persistent grants") introduced a regression as purged persistent
grants were not pu into the list of free grants again. Correct that.
pinctrl: sh-pfc: rcar: Rename automotive-only arrays to automotive
Renesas RZ/G SoCs are pin compatible with R-Car SoCs, but lack several
automotive-specific peripherals.
Currently pin groups and functions for automotive-specific peripherals
are grouped in arrays named after the automative SoC part numbers.
Rename them to "automotive" for clarity and consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Baolin Wang [Thu, 27 Sep 2018 09:15:08 +0000 (17:15 +0800)]
pinctrl: sprd: Move DT parsing before registering pinctrl device
It will be failed to select default or sleep state for pins hogged
by the pin controller device, since we hadn't parsed pins configuration
in device tree before registering the pin controller device. Thus
we should move the device tree parsing function before registering
the pin controller device.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: mediatek: mark dummy helpers as 'static inline'
mtk_eint_set_debounce and mtk_eint_find_irq are defined as stub functions
in a header file, but without marking them as 'static inline', we get
a copy for each file that includes the header:
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.o: In function `mtk_eint_set_debounce':
pinctrl-mtk-common-v2.c:(.text+0x134): multiple definition of `mtk_eint_set_debounce'
drivers/pinctrl/mediatek/pinctrl-moore.o:pinctrl-moore.c:(.text+0x7d0): first defined here
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.o: In function `mtk_eint_find_irq':
pinctrl-mtk-common-v2.c:(.text+0x13c): multiple definition of `mtk_eint_find_irq'
Fixes: e46df235b4e6 ("pinctrl: mediatek: refactor EINT related code for all MediaTek pinctrl can fit") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Michael Ellerman [Fri, 28 Sep 2018 04:53:18 +0000 (14:53 +1000)]
selftests/powerpc: Fix Makefiles for headers_install change
Commit b2d35fa5fc80 ("selftests: add headers_install to lib.mk")
introduced a requirement that Makefiles more than one level below the
selftests directory need to define top_srcdir, but it didn't update
any of the powerpc Makefiles.
This broke building all the powerpc selftests with eg:
make[1]: Entering directory '/src/linux/tools/testing/selftests/powerpc'
BUILD_TARGET=/src/linux/tools/testing/selftests/powerpc/alignment; mkdir -p $BUILD_TARGET; make OUTPUT=$BUILD_TARGET -k -C alignment all
make[2]: Entering directory '/src/linux/tools/testing/selftests/powerpc/alignment'
../../lib.mk:20: ../../../../scripts/subarch.include: No such file or directory
make[2]: *** No rule to make target '../../../../scripts/subarch.include'.
make[2]: Failed to remake makefile '../../../../scripts/subarch.include'.
Makefile:38: recipe for target 'alignment' failed
Fix it by setting top_srcdir in the affected Makefiles.
Fixes: b2d35fa5fc80 ("selftests: add headers_install to lib.mk") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Jason writes:
"Second RDMA rc pull request
- Fix a long standing race bug when destroying comp_event file descriptors
- srp, hfi1, bnxt_re: Various driver crashes from missing validation
and other cases
- Fixes for regressions in patches merged this window in the gid
cache, devx, ucma and uapi."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/core: Set right entry state before releasing reference
IB/mlx5: Destroy the DEVX object upon error flow
IB/uverbs: Free uapi on destroy
RDMA/bnxt_re: Fix system crash during RDMA resource initialization
IB/hfi1: Fix destroy_qp hang after a link down
IB/hfi1: Fix context recovery when PBC has an UnsupportedVL
IB/hfi1: Invalid user input can result in crash
IB/hfi1: Fix SL array bounds check
RDMA/uverbs: Fix validity check for modify QP
IB/srp: Avoid that sg_reset -d ${srp_device} triggers an infinite loop
ucma: fix a use-after-free in ucma_resolve_ip()
RDMA/uverbs: Atomically flush and mark closed the comp event queue
cxgb4: fix abort_req_rss6 struct
blk-mq: I/O and timer unplugs are inverted in blktrace
trace_block_unplug() takes true for explicit unplugs and false for
implicit unplugs. schedule() unplugs are implicit and should be
reported as timer unplugs. While correct in the legacy code, this has
been inverted in blk-mq since 4.11.
Jan Kara [Thu, 27 Sep 2018 11:23:32 +0000 (13:23 +0200)]
dax: Fix deadlock in dax_lock_mapping_entry()
When dax_lock_mapping_entry() has to sleep to obtain entry lock, it will
fail to unlock mapping->i_pages spinlock and thus immediately deadlock
against itself when retrying to grab the entry lock again. Fix the
problem by unlocking mapping->i_pages before retrying.
Fixes: c2a7d2a11552 ("filesystem-dax: Introduce dax_lock_mapping_entry()") Reported-by: Barret Rhoden <brho@google.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Kairui Song [Thu, 27 Sep 2018 12:38:45 +0000 (20:38 +0800)]
x86/boot: Fix kexec booting failure in the SEV bit detection code
Commit
1958b5fc4010 ("x86/boot: Add early boot support when running with SEV active")
can occasionally cause system resets when kexec-ing a second kernel even
if SEV is not active.
That's because get_sev_encryption_bit() uses 32-bit rIP-relative
addressing to read the value of enc_bit - a variable which caches a
previously detected encryption bit position - but kexec may allocate
the early boot code to a higher location, beyond the 32-bit addressing
limit.
In this case, garbage will be read and get_sev_encryption_bit() will
return the wrong value, leading to accessing memory with the wrong
encryption setting.
Therefore, remove enc_bit, and thus get rid of the need to do 32-bit
rIP-relative addressing in the first place.
[ bp: massage commit message heavily. ]
Fixes: 1958b5fc4010 ("x86/boot: Add early boot support when running with SEV active") Suggested-by: Borislav Petkov <bp@suse.de> Signed-off-by: Kairui Song <kasong@redhat.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Cc: linux-kernel@vger.kernel.org Cc: tglx@linutronix.de Cc: mingo@redhat.com Cc: hpa@zytor.com Cc: brijesh.singh@amd.com Cc: kexec@lists.infradead.org Cc: dyoung@redhat.com Cc: bhe@redhat.com Cc: ghook@redhat.com Link: https://lkml.kernel.org/r/20180927123845.32052-1-kasong@redhat.com
bcache: add separate workqueue for journal_write to avoid deadlock
After write SSD completed, bcache schedules journal_write work to
system_wq, which is a public workqueue in system, without WQ_MEM_RECLAIM
flag. system_wq is also a bound wq, and there may be no idle kworker on
current processor. Creating a new kworker may unfortunately need to
reclaim memory first, by shrinking cache and slab used by vfs, which
depends on bcache device. That's a deadlock.
This patch create a new workqueue for journal_write with WQ_MEM_RECLAIM
flag. It's rescuer thread will work to avoid the deadlock.
[Why]
EDID emulation didn't work properly for linux, as we stop programming
if nothing is connected physically.
[How]
We get a flag from DRM when we want to do edid emulation. We check if
this flag is true and nothing is connected physically, if so we only
program the front end using VIRTUAL_SIGNAL.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Roman Li [Wed, 26 Sep 2018 17:42:16 +0000 (13:42 -0400)]
drm/amd/display: Fix Vega10 lightup on S3 resume
[Why]
There have been a few reports of Vega10 display remaining blank
after S3 resume. The regression is caused by workaround for mode
change on Vega10 - skip set_bandwidth if stream count is 0.
As a result we skipped dispclk reset on suspend, thus on resume
we may skip the clock update assuming it hasn't been changed.
On some systems it causes display blank or 'out of range'.
[How]
Revert "drm/amd/display: Fix Vega10 black screen after mode change"
Verified that it hadn't cause mode change regression.
Signed-off-by: Roman Li <Roman.Li@amd.com> Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rex Zhu [Thu, 27 Sep 2018 12:48:39 +0000 (20:48 +0800)]
drm/amdgpu: Fix vce work queue was not cancelled when suspend
The vce cancel_delayed_work_sync never be called.
driver call the function in error path.
This caused the A+A suspend hang when runtime pm enebled.
As we will visit the smu in the idle queue. this will cause
smu hang because the dgpu has been suspend, and the dgpu also
will be waked up. As the smu has been hang, so the dgpu resume
will failed.
Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
commit 0c08754b59da
("drm/panel: Add device_link from panel device to DRM device")
creates a circular dependency under these circumstances:
1. The panel depends on dsi-host because it is MIPI-DSI child
device.
2. dsi-host depends on the drm parent device (connector->dev->dev)
this should be allowed.
3. drm parent dev (connector->dev->dev) depends on the panel
after this patch.
This makes the dependency circular and while it appears it
does not affect any in-tree drivers (they do not seem to have
dsi hosts depending on the same parent device) this does not
seem right.
As noted in a response from Andrzej Hajda, the intent is
likely to make the panel dependent on the DRM device
(connector->dev) not its parent. But we have no way of
doing that since the DRM device doesn't contain any
struct device on its own (arguably it should).
Revert this until a proper approach is figured out.
Boris Ostrovsky [Sat, 22 Sep 2018 19:55:49 +0000 (15:55 -0400)]
xen/blkfront: When purging persistent grants, keep them in the buffer
Commit a46b53672b2c ("xen/blkfront: cleanup stale persistent grants")
added support for purging persistent grants when they are not in use. As
part of the purge, the grants were removed from the grant buffer, This
eventually causes the buffer to become empty, with BUG_ON triggered in
get_free_grant(). This can be observed even on an idle system, within
20-30 minutes.
We should keep the grants in the buffer when purging, and only free the
grant ref.
Fixes: a46b53672b2c ("xen/blkfront: cleanup stale persistent grants") Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Damien Le Moal [Thu, 27 Sep 2018 01:55:13 +0000 (10:55 +0900)]
block: fix deadline elevator drain for zoned block devices
When the deadline scheduler is used with a zoned block device, writes
to a zone will be dispatched one at a time. This causes the warning
message:
deadline: forced dispatching is broken (nr_sorted=X), please report this
to be displayed when switching to another elevator with the legacy I/O
path while write requests to a zone are being retained in the scheduler
queue.
Prevent this message from being displayed when executing
elv_drain_elevator() for a zoned block device. __blk_drain_queue() will
loop until all writes are dispatched and completed, resulting in the
desired elevator queue drain without extensive modifications to the
deadline code itself to handle forced-dispatch calls.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Fixes: 8dc8146f9c92 ("deadline-iosched: Introduce zone locking support") Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
Dave Airlie [Thu, 27 Sep 2018 00:19:26 +0000 (10:19 +1000)]
Merge branch 'etnaviv/fixes' of https://git.pengutronix.de/git/lst/linux into drm-fixes
one fix to get a proper DMA configuration in place for the etnaviv
virtual device. I'm sending this as a fix, as a dma-mapping change at
the ARC architecture side during the 4.19 cycle broke etnaviv on this
platform, which gets remedied with this patch, but it also enables
ARM64.
Mika Westerberg [Wed, 26 Sep 2018 20:39:28 +0000 (15:39 -0500)]
ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
HP 6730b laptop has an ethernet NIC connected to one of the PCIe root
ports. The root ports themselves are native PCIe hotplug capable. Now,
during boot after PCI devices are scanned the BIOS triggers ACPI bus check
directly to the NIC:
ACPI: \_SB_.PCI0.RP06.NIC_: Bus check in hotplug_event()
It is not clear why it is sending bus check but regardless the ACPI hotplug
notify handler calls enable_slot() directly (instead of going through
acpiphp_check_bridge() as there is no bridge), which ends up handling
special case for non-hotplug bridges with native PCIe hotplug. This
results a crash of some kind but the reporter only sees black screen so it
is hard to figure out the exact spot and what actually happens. Based on
a few fix proposals it was tracked to crash somewhere inside
pci_assign_unassigned_bridge_resources().
In any case we should not really be in that special branch at all because
the ACPI notify happened to a slot that is not a PCI bridge (it is just a
regular PCI device).
Fix this so that we only go to that special branch if we are calling
enable_slot() for a bridge (e.g., the ACPI notification was for the
bridge).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201127 Fixes: 84c8b58ed3ad ("ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug") Reported-by: Peter Anemone <peter.anemone@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> CC: stable@vger.kernel.org # v4.18+
Jason Ekstrand [Wed, 26 Sep 2018 07:17:03 +0000 (02:17 -0500)]
drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
We attempt to get fences earlier in the hopes that everything will
already have fences and no callbacks will be needed. If we do succeed
in getting a fence, getting one a second time will result in a duplicate
ref with no unref. This is causing memory leaks in Vulkan applications
that create a lot of fences; playing for a few hours can, apparently,
bring down the system.
Merge tag 'iommu-fixes-v4.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Joerg writes:
"IOMMU Fixes for Linux v4.19-rc5
Three fixes queued up:
- Warning fix for Rockchip IOMMU where there were IRQ handlers
for offlined hardware.
- Fix for Intel VT-d because recent changes caused boot failures
on some machines because it tried to allocate to much
contiguous memory.
- Fix for AMD IOMMU to handle eMMC devices correctly that appear
as ACPI HID devices."
* tag 'iommu-fixes-v4.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Return devid as alias for ACPI HID devices
iommu/vt-d: Handle memory shortage on pasid table allocation
iommu/rockchip: Free irqs in shutdown handler
Colin Ian King [Tue, 25 Sep 2018 09:55:56 +0000 (10:55 +0100)]
pinctrl: mediatek: fix check on EINT_NA comparison
Currently, the check on desc->eint.eint_n == EINT_NA is always false
because this is comparing a u16 to -1 which can never be true. Fix
this by casting EINT_NA to u16.
Detected by CoverityScan, CID#1473610 ("Operands don't affect result")
Fixes: fb5fa8dc151b ("pinctrl: mediatek: extend struct mtk_pin_desc to pinctrl-mtk-common-v2.c") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
iommu/amd: Return devid as alias for ACPI HID devices
ACPI HID devices do not actually have an alias for
them in the IVRS. But dev_data->alias is still used
for indexing into the IOMMU device table for devices
being handled by the IOMMU. So for ACPI HID devices,
we simply return the corresponding devid as an alias,
as parsed from IVRS table.
Signed-off-by: Arindam Nath <arindam.nath@amd.com> Fixes: 2bf9a0a12749 ('iommu/amd: Add iommu support for ACPI HID devices') Signed-off-by: Joerg Roedel <jroedel@suse.de>
On some new platforms the tiles have been placed too far apart to be
covered in a single ioremap. Turn "regs" into an array of base addresses
and make the pingroup carry the information about which tile the pin
resides in.
For existing platforms we map the first entry regs and the existing
pingroups will all use tile 0, meaning that there's no functional
change.
In preparation for the support for dispersed tiles move all readl and
writel calls to helper functions. This will allow us to isolate the
added complexity of another indirection.
Keith Busch [Tue, 25 Sep 2018 16:36:20 +0000 (10:36 -0600)]
blk-mq: Allow blocking queue tag iter callbacks
A recent commit runs tag iterator callbacks under the rcu read lock,
but existing callbacks do not satisfy the non-blocking requirement.
The commit intended to prevent an iterator from accessing a queue that's
being modified. This patch fixes the original issue by taking a queue
reference instead of reading it, which allows callbacks to make blocking
calls.
Fixes: f5bbbbe4d6357 ("blk-mq: sync the update nr_hw_queues with blk_mq_queue_tag_busy_iter") Acked-by: Jianchao Wang <jianchao.w.wang@oracle.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
RDMA/core: Set right entry state before releasing reference
Currently add_modify_gid() for IB link layer has followong issue
in cache update path.
When GID update event occurs, core releases reference to the GID
table without updating its state and/or entry pointer.
CPU-0 CPU-1
------ -----
ib_cache_update() IPoIB ULP
add_modify_gid() [..]
put_gid_entry()
refcnt = 0, but
state = valid,
entry is valid.
(work item is not yet executed).
ipoib_create_ah()
rdma_create_ah()
rdma_get_gid_attr() <--
Tries to acquire gid_attr
which has refcnt = 0.
This is incorrect.
GID entry state and entry pointer is provides the accurate GID enty
state. Such fields must be updated with rwlock to protect against
readers and, such fields must be in sane state before refcount can drop
to zero. Otherwise above race condition can happen leading to
use-after-free situation.
Following backtrace has been observed when cache update for an IB port
is triggered while IPoIB ULP is creating an AH.
Therefore, when updating GID entry, first mark a valid entry as invalid
through state and set the barrier so that no callers can acquired
the GID entry, followed by release reference to it.
Mark Bloch [Tue, 25 Sep 2018 08:23:55 +0000 (11:23 +0300)]
IB/uverbs: Free uapi on destroy
Make sure we free struct uverbs_api once we clean the radix tree. It was
allocated by uverbs_alloc_api().
Fixes: 9ed3e5f44772 ("IB/uverbs: Build the specs into a radix tree at runtime") Reported-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
erge tag 'libnvdimm-fixes-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Dan writes:
"libnvdimm/dax for 4.19-rc6
* (2) fixes for the dax error handling updates that were merged for
v4.19-rc1. My mails to Al have been bouncing recently, so I do not have
his ack but the uaccess change is of the trivial / obviously correct
variety. The address_space_operations fixes a regression.
* A filesystem-dax fix to correct the zero page lookup to be compatible
with non-x86 (mips and s390) architectures."
* tag 'libnvdimm-fixes-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: Add missing address_space_operations
uaccess: Fix is_source param for check_copy_size() in copy_to_iter_mcsafe()
filesystem-dax: Fix use of zero page
Nine obvious bug fixes mostly in individual drivers. The target fix
is of particular importance because it's CVE related."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: don't crash the host on invalid commands
scsi: ipr: System hung while dlpar adding primary ipr adapter back
scsi: target: iscsi: Use bin2hex instead of a re-implementation
scsi: target: iscsi: Use hex2bin instead of a re-implementation
scsi: lpfc: Synchronize access to remoteport via rport
scsi: ufs: Disable blk-mq for now
scsi: sd: Contribute to randomness when running rotational device
scsi: ibmvscsis: Ensure partition name is properly NUL terminated
scsi: ibmvscsis: Fix a stringop-overflow warning
Merge tag 'usb-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
I wrote:
"USB fixes for 4.19-rc6
Here are some small USB core and driver fixes for reported issues for
4.19-rc6.
The most visible is the oops fix for when the USB core is built into the
kernel that is present in 4.18. Turns out not many people actually do
that so it went unnoticed for a while. The rest is some tiny typec,
musb, and other core fixes.
All have been in linux-next with no reported issues."
* tag 'usb-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: mux: Take care of driver module reference counting
usb: core: safely deal with the dynamic quirk lists
usb: roles: Take care of driver module reference counting
USB: handle NULL config in usb_find_alt_setting()
USB: fix error handling in usb_driver_claim_interface()
USB: remove LPM management from usb_driver_claim_interface()
USB: usbdevfs: restore warning for nonsensical flags
USB: usbdevfs: sanitize flags more
Revert "usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()"
usb: musb: dsps: do not disable CPPI41 irq in driver teardown
Merge tag 'tty-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
I wrote:
"TTY/Serial driver fixes for 4.19-rc6
Here are a number of small tty and serial driver fixes for reported
issues for 4.19-rc6.
One should hopefully resolve a much-reported issue that syzbot has found
in the tty layer. Although there are still more issues there, getting
this fixed is nice to see finally happen.
All of these have been in linux-next for a while with no reported
issues."
* tag 'tty-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: imx: restore handshaking irq for imx1
tty: vt_ioctl: fix potential Spectre v1
tty: Drop tty->count on tty_reopen() failure
serial: cpm_uart: return immediately from console poll
tty: serial: lpuart: avoid leaking struct tty_struct
serial: mvebu-uart: Fix reporting of effective CSIZE to userspace
powerpc/numa: Use associativity if VPHN hcall is successful
Currently associativity is used to lookup node-id even if the
preceding VPHN hcall failed. However this can cause CPU to be made
part of the wrong node, (most likely to be node 0). This is because
VPHN is not enabled on KVM guests.
With 2ea6263 ("powerpc/topology: Get topology for shared processors at
boot"), associativity is used to set to the wrong node. Hence KVM
guest topology is broken.
For example : A 4 node KVM guest before would have reported.
Fix this by skipping associativity lookup if the VPHN hcall failed.
Fixes: 2ea626306810 ("powerpc/topology: Get topology for shared processors at boot") Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Tue, 25 Sep 2018 09:36:47 +0000 (19:36 +1000)]
powerpc/tm: Avoid possible userspace r1 corruption on reclaim
Current we store the userspace r1 to PACATMSCRATCH before finally
saving it to the thread struct.
In theory an exception could be taken here (like a machine check or
SLB miss) that could write PACATMSCRATCH and hence corrupt the
userspace r1. The SLB fault currently doesn't touch PACATMSCRATCH, but
others do.
We've never actually seen this happen but it's theoretically
possible. Either way, the code is fragile as it is.
This patch saves r1 to the kernel stack (which can't fault) before we
turn MSR[RI] back on. PACATMSCRATCH is still used but only with
MSR[RI] off. We then copy r1 from the kernel stack to the thread
struct once we have MSR[RI] back on.
Suggested-by: Breno Leitao <leitao@debian.org> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Mon, 24 Sep 2018 07:27:04 +0000 (17:27 +1000)]
powerpc/tm: Fix userspace r13 corruption
When we treclaim we store the userspace checkpointed r13 to a scratch
SPR and then later save the scratch SPR to the user thread struct.
Unfortunately, this doesn't work as accessing the user thread struct
can take an SLB fault and the SLB fault handler will write the same
scratch SPRG that now contains the userspace r13.
To fix this, we store r13 to the kernel stack (which can't fault)
before we access the user thread struct.
Found by running P8 guest + powervm + disable_1tb_segments + TM. Seen
as a random userspace segfault with r13 looking like a kernel address.
Signed-off-by: Michael Neuling <mikey@neuling.org> Reviewed-by: Breno Leitao <leitao@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Lu Baolu [Sat, 8 Sep 2018 01:42:53 +0000 (09:42 +0800)]
iommu/vt-d: Handle memory shortage on pasid table allocation
Pasid table memory allocation could return failure due to memory
shortage. Limit the pasid table size to 1MiB because current 8MiB
contiguous physical memory allocation can be hard to come by. W/o
a PASID table, the device could continue to work with only shared
virtual memory impacted. So, let's go ahead with context mapping
even the memory allocation for pasid table failed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107783 Fixes: cc580e41260d ("iommu/vt-d: Per PCI device pasid table interfaces") Cc: Ashok Raj <ashok.raj@intel.com> Cc: Jacob Pan <jacob.jun.pan@linux.intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Reported-and-tested-by: Pelton Kyle D <kyle.d.pelton@intel.com> Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
Revert "uapi/linux/keyctl.h: don't use C++ reserved keyword as a struct member name"
This changes UAPI, breaking iwd and libell:
ell/key.c: In function 'kernel_dh_compute':
ell/key.c:205:38: error: 'struct keyctl_dh_params' has no member named 'private'; did you mean 'dh_private'?
struct keyctl_dh_params params = { .private = private,
^~~~~~~
dh_private
Fixes: 8a2336e549d3 ("uapi/linux/keyctl.h: don't use C++ reserved keyword as a struct member name") Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Randy Dunlap <rdunlap@infradead.org>
cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
cc: Stephan Mueller <smueller@chronox.de>
cc: James Morris <jmorris@namei.org>
cc: "Serge E. Hallyn" <serge@hallyn.com>
cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: Linus Torvalds <torvalds@linux-foundation.org>
cc: <stable@vger.kernel.org> Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 55aedef50d4d ("pinctrl: intel: Do pin translation when lock IRQ")
added special translation from GPIO number to hardware pin number to
irq_reqres/relres hooks to avoid failure when IRQs are requested. The
actual failure happened inside gpiochip_lock_as_irq() because it calls
gpiod_get_direction() and pinctrl-intel.c::intel_gpio_get_direction()
implementation originally missed the translation so the two hooks made
it work by skipping the ->get_direction() call entirely (it overwrote
the default GPIOLIB provided functions).
The proper fix that adds translation to GPIO callbacks was merged with
commit 96147db1e1df ("pinctrl: intel: Do pin translation in other GPIO
operations as well"). This allows us to use the default GPIOLIB provided
functions again.
In addition as find out by Benjamin Tissoires the two functions
(intel_gpio_irq_reqres()/intel_gpio_irq_relres()) now cause problems of
their own because they operate on pin numbers and pass that pin number
to gpiochip_lock_as_irq() which actually expects a GPIO number.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199911 Fixes: 55aedef50d4d ("pinctrl: intel: Do pin translation when lock IRQ") Reported-and-tested-by: Benjamin Tissoires <benjamin.tissoires@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
projects / thirdparty / linux.git / log
