Jouni Malinen [Sun, 16 Dec 2012 16:22:54 +0000 (18:22 +0200)]
WNM: Use CONFIG_WNM more consistently
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.
Jouni Malinen [Sun, 16 Dec 2012 10:35:07 +0000 (12:35 +0200)]
wlantest: Process TX status frames as RX frames too
This is needed to allow capture files from the mac80211 cooked monitor
mode interface to be processed properly. Without this, the locally
generated frames may not get processed.
Jouni Malinen [Sun, 16 Dec 2012 10:31:16 +0000 (12:31 +0200)]
WNM: Add option for passing TFS request from external programs
The optional tfs_req=<hex dump> parameter can be added for the wnm_sleep
command to specify the TFS request element to use in the WNM-Sleep Mode
Request frame.
Dan Williams [Sun, 25 Nov 2012 19:27:18 +0000 (21:27 +0200)]
PMKSA: Make deauthentication due to cache entry removal more granular
Expiry can always trigger a deauthentication, but otherwise,
deauthentication should only happen when the *current* cache entry is
removed and not being replaced. It should not happen when the current
PMK just happens to match the PMK of the entry being removed, since
multiple entries can have the same PMK when OKC is used and these
entries are often removed at different times.
This fixes an issue where eviction of the oldest inactive entry due to
adding a newer entry to a full cache caused a deauthentication when the
entry being removed had the same PMK as the current entry.
Michael Braun [Sun, 25 Nov 2012 15:49:25 +0000 (17:49 +0200)]
Keep and use list of PSKs per station for RADIUS-based PSK
This adds support for multiple PSKs per station when using a RADIUS
authentication server to fetch the PSKs during MAC address
authentication step. This can be useful if multiple users share a
device but each user has his or her own private passphrase.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Jouni Malinen [Sun, 25 Nov 2012 14:30:30 +0000 (16:30 +0200)]
Use a shared function for requesting a new connection
Both the ctrl_iface and D-Bus interface use similar functionality to
request a new connection. Combine these to a single function to avoid
need to maintain duplicated implementation.
Jouni Malinen [Sun, 25 Nov 2012 14:20:44 +0000 (16:20 +0200)]
Maintain maximum blacklist count over list clear operations
wpas_connection_failed() uses the blacklist count to figure out a
suitable time to wait for the next scan. This mechanism did not work
properly in cases where the temporary blacklist gets cleared due to no
other BSSes being available. Address this by maintaining an additional
count of blacklisting values over wpa_blacklist_clear() calls. In
addition, add one more step in the count to timeout mapping to go to 10
second interval if more than four failures are seen.
Jouni Malinen [Sun, 25 Nov 2012 10:47:43 +0000 (12:47 +0200)]
P2P: Avoid multi-channel scans when they are not needed
If the driver does not support multi-channel concurrency and a virtual
interface that shares the same radio with the current interface is
operating there may not be need to scan other channels apart from the
current operating channel on the other virtual interface. Filter out
other channels in case we are trying to find a connection for a station
interface when we are not configured to prefer station connection and a
concurrent operation is already in process.
Jouni Malinen [Sat, 24 Nov 2012 20:45:17 +0000 (22:45 +0200)]
Indicate if PMF was negotiated for the connection
Add pmf=1/2 to wpa_supplicant STATUS command output to indicate that PMF
was negotiated for the connect (1 = optional in this BSS, 2 = required
in this BSS).
Jouni Malinen [Sat, 24 Nov 2012 20:31:17 +0000 (22:31 +0200)]
Interworking: Enable key_mgmt WPA-EAP-SHA256 if PMF is enabled
If the global pmf=1/2 parameter is used to enable PMF for Interworking
networks, add WPA-EAP-SHA256 to the temporary network block to allow
connection to PMF required APs.
Jouni Malinen [Sat, 24 Nov 2012 20:21:29 +0000 (22:21 +0200)]
Allow PMF to be enabled by default
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.
Johannes Berg [Sat, 24 Nov 2012 16:02:29 +0000 (18:02 +0200)]
hostapd: Add second VHT frequency segment config
Add the configuration option vht_oper_centr_freq_seg1_idx
for the second segment of an 80+80 MHz channel and use it
when building the VHT operation IE.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Pontus Fuchs [Sat, 24 Nov 2012 14:47:20 +0000 (16:47 +0200)]
Do not double free cfg struct if netlink_init() fails
If netlink_init() fails on socket create or bind the cfg struct
provided as parameter is freed by netlink_init(). Callers of
netlink_init() also free this struct on their error paths leading
to double free.
Jouni Malinen [Thu, 22 Nov 2012 18:51:49 +0000 (20:51 +0200)]
HS 2.0: Add Home SP FQDN and roaming/home to status command
This allows the ctrl_iface STATUS information to be used to determine
which Home SP credential (domain in the cred block) was used and whether
the network is operated by the home SP.
Jouni Malinen [Thu, 22 Nov 2012 16:04:57 +0000 (18:04 +0200)]
HS 2.0: Add REMOVE_CRED sp_fqdn=<FQDN> command
This allows credential entries to be removed based on SP FQDN without
having to iterate through the configured entries from an external
program to figure out which credentials should be removed for a specific
SP.
Jouni Malinen [Wed, 21 Nov 2012 22:19:17 +0000 (00:19 +0200)]
HS 2.0: Maintain a copy of HS 2.0 Indication from Association Request
This allows the AP to figure out whether a station is a HS 2.0 STA
during the association and access any information that the STA may have
included in this element.
Jouni Malinen [Fri, 23 Nov 2012 15:05:47 +0000 (17:05 +0200)]
Android: Force group access to ctrl_iface directory
wpa_supplicant is started from /init.*.rc on Android and that seems
to be using umask 0077 which would leave the control interface
directory without group access. This breaks things since Wi-Fi
framework assumes that this directory can be accessed by other
applications in the wifi group. Fix this by adding group access even
if umask value would prevent this.
In most cases, this issue was not hit since the control interface
directory is normally created by that same init.*.rc file with suitable
mode and wpa_supplicant is killed in the way that does not allow it to
remove the file. However, if wpa_supplicant is allowed stop cleanly, it
will remove the directory and the next start could result with the Wi-Fi
framework not being able to use Wi-Fi (and GUI not showing Wi-Fi getting
enabled).
Sunil Dutt [Thu, 22 Nov 2012 22:57:59 +0000 (00:57 +0200)]
P2P: Increase the maximum number of PD Request retries
Change the maximum retry limit from 10 to 120 to match the behavior
used with GO Negotiation Request frames when trying to start GO
Negotiation with a peer that does not acknowledge frames (e.g., due
to being in sleep or on another channel most of the time).
Sunil Dutt [Thu, 22 Nov 2012 23:14:15 +0000 (01:14 +0200)]
P2P: Remove PD-before-join-timeout mechanism
The PD Request retry limit can be used to achieve the same behavior,
so drop this duplicated timeout mechanism and control the timeout
based on MAX_PROV_DISC_REQ_RETRIES.
Jouni Malinen [Thu, 22 Nov 2012 22:53:42 +0000 (00:53 +0200)]
P2P: Retry PD Request in join-a-running-group case
The GO may be in sleep when we send a PD Request frame to indicate that
we are about to join a running group. Previously, this frame was not
retried more than normal low level retries. This can result in the GO
not getting the frame especially in cases where concurrent multi-channel
operations or aggressive sleep schedule is used since most drivers do
not yet synchronize with the GO's NoA before association.
Increase the likelihood of the GO receiving the PD Request frame by
retransmitting it similarly to the PD-for-GO-Negotiation case. Start
the actual join operation only after these retries have failed to get
an acknowledgment from the GO to give the connection attempt a chance
to succeed if the driver implements better NoA synchronization for it.
Sunil Dutt [Thu, 22 Nov 2012 22:48:58 +0000 (00:48 +0200)]
P2P: Set user_initiated_pd separately from the join parameter
p2p_prov_disc_req() used the join parameter to figure out whether the PD
request was a user initiated or not. This does not cover all use cases
of PD, so add a separate parameter to allow caller to indicate whether
the user requested the operation.
../src/ap/ieee802_1x.o: In function `ieee802_1x_get_eap_user':
/../src/ap/ieee802_1x.c:1689: undefined reference to `hostapd_get_eap_user'
collect2: error: ld returned 1 exit status
make: *** [wpa_supplicant] Error 1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Jouni Malinen [Tue, 20 Nov 2012 22:47:47 +0000 (00:47 +0200)]
Add preliminary support for using SQLite for eap_user database
CONFIG_SQLITE=y option can now be used to allow the eap_user_file text
file to be replaced with a SQLite database
(eap_user_file=sqlite:/path/to/sqlite.db). hostapd.eap_user_sqlite
shows an example of how the database tables can be created for this
purpose. This commit does not yet include full functionality of the
text file format, but at least basic EAP-TTLS/MSCHAPv2 style
authentication mechanisms with plaintext passwords can be used for
tests.
Jouni Malinen [Mon, 19 Nov 2012 15:00:07 +0000 (17:00 +0200)]
nl80211: Add support for TDLS request event from the driver
The NL80211_CMD_TDLS_OPER command can be used as an event based on a
recent cfg80211 commit, so add code to map that to internal
wpa_supplicant event to request TDLS link setup/teardown.
Jouni Malinen [Mon, 19 Nov 2012 12:04:42 +0000 (14:04 +0200)]
wpa_cli: Accept more arguments for set_network
Some network parameters, e.g., auth_alg and eap use a space separated
list of values without quotation marks. To allow these to be entered
from the interactive mode, change set_network command to allow more than
three arguments.
Jouni Malinen [Sun, 18 Nov 2012 11:06:03 +0000 (13:06 +0200)]
hostapd: Fix a regression in TKIP countermeasures processing
Commit 296a34f0c1730416bf2a61ab78690be43d82a3c0 changed hostapd to
remove the internal STA entry at the beginning of TKIP countermeasures.
However, this did not take into account the case where this is triggered
by an EAPOL-Key error report from a station. In such a case, WPA
authenticator state machine may continue processing after having
processed the error report. This could result in use of freed memory.
Fix this by stopping WPA processing if the STA entry got removed.
Jouni Malinen [Thu, 15 Nov 2012 17:59:04 +0000 (19:59 +0200)]
WPS: Add a workaround for PBC session overlap detection
Some deployed station implementations implement WPS incorrectly and
end up causing PBC session overlap issues by indicating active PBC
mode in a scan after the WPS provisioning step. Work around this by
ignoring active PBC indication in a Probe Request from a station that
completed PBC provisioning during the last five seconds.
Jouni Malinen [Wed, 14 Nov 2012 11:05:53 +0000 (13:05 +0200)]
Fix forgotten no-CONFIG_WPS=y wrapper
Commit 620c783753bddd37988269314862dc7e4a62f700 modified
wpas_wps_ssid_wildcard_ok() prototype, but forgot to update the
non-WPS-build wrapper. Fix that to match with the new bss parameter
type and remove the now unused declaration of wpa_scan_res.
Jouni Malinen [Mon, 12 Nov 2012 18:07:53 +0000 (20:07 +0200)]
Allow OKC to be enabled by default
Previously, OKC (opportunistic key caching, a.k.a. proactive key
caching) could be enabled only with a per-network parameter
(proactive_key_caching). The new global parameter (okc) can now be used
to change the default behavior to be OKC enabled (okc=1) for network
blocks that do not override this with the proactive_key_caching
parameter.
Jouni Malinen [Sun, 11 Nov 2012 18:45:27 +0000 (20:45 +0200)]
P2P: Avoid extra group interface creation on GO reinvocation
If separate group interfaces are used, the pending group interface got
removed unnecessarily when stopping find operations when accepting an
invitation to reinvoke the group in GO role. This resulted in the group
interfaces getting created twice. Avoid this unnecessary extra operation
by skipping removal of the pending interface in the reinvocation
sequence.
Pawel Kulakowski [Sun, 11 Nov 2012 14:26:36 +0000 (16:26 +0200)]
bgscan_learn: Prevent infinite busy looping
In highly congested network (BSSes almost on every channel
within ESS) we have hit a bug when wpa_supplicant become
completly irresponsive, infinite looping on while loop.
When probe_idx was equal 0 and we are not able to probe
new frequency, following condition were never fulfilled:
"if (!in_array(freqs, data->supp_freqs[idx]))"
nl80211: Roam correctly through cfg80211 without SME
Change the nl80211 driver in wpa_supplicant to correctly handle
connecting to a new AP through cfg80211 without SME capability. As
before, the driver will disconnect from the previously associated AP,
but now we attempt to immediately connect to our intended AP. This
prevents us from blacklisting the AP we were trying to connect to
because of a semantic mismatch between cfg80211 and wpa_supplicant. The
disconnect/connect patch generates a local disconnect nl80211 event
which we discard because we're already correctly tracking the pending
association request.
In detail:
cfg80211 does not support connecting to a new BSS while already
connected to another BSS, if the underlying driver doesn't support
separate authenticate and associate commands. wpa_supplicant is written
to expect that this is a supported operation, except for a little error
handling that disconnects from the current BSS when roaming fails and
relies on autoconnect logic to reconnect later. However, this failure to
connect is incorrectly attributed to the new AP we attempted to
associate with, rather than a local condition in cfg80211.
The combined effect of these two conditions is that full-mac drivers
accessible through cfg80211 but without SME capability take a long time
to roam across BSS's because wpa_supplicant will:
1) Fail to associate for local reasons
2) Disconnect and return that the association request failed
3) Blacklist the association target (incorrectly)
4) Do a scan
5) Pick a less desirable AP to associate with
Jouni Malinen [Sun, 11 Nov 2012 11:11:15 +0000 (13:11 +0200)]
Check hapd_iface more consistently in hostapd_disable_iface()
There is no point in the hapd_iface == NULL validate after this pointer
has been dereferences, so move the code dereferencing hapd_iface after
the check.
Jouni Malinen [Sun, 11 Nov 2012 11:01:06 +0000 (13:01 +0200)]
WPS: Remove deprecated UFD config method and OOB ctrl_iface
The UFD (USB flash drive) configuration method was deprecated in WSC
2.0. Since this is not known to be used, remove the UFD implementation
from hostapd and wpa_supplicant to allow the WPS implementation to be
cleaned up. This removes the now unused OOB operations and ctrl_iface
commands that had already been deprecated by the new NFC operations.
Masashi Honma [Sun, 11 Nov 2012 09:39:24 +0000 (11:39 +0200)]
P2P: Reduce redundant PSK generation for GO
The PSK generation done by pbkdf2_sha1() is one of the longest CPU time
users according to our profiling from boot to GO started.
So I have reduced some steps.
I could boot a GO by this command sequence.
-------------
add_net
set_network 0 ssid '"DIRECT-XX"'
set_network 0 psk
'"123456789012345678901234567890123456789012345678901234567890123"'
set_network 0 proto RSN
set_network 0 key_mgmt WPA-PSK
set_network 0 pairwise CCMP
set_network 0 auth_alg OPEN
set_network 0 mode 3
set_network 0 disabled 2
p2p_group_add persistent=0 freq=2412
-------------
By this sequence, pbkdf2_sha1() was called three times and the function
calculates the same value each time. Reduce number of calls to
pbkdf2_sha1() from 3 to 1 by caching the previous result.
Signed-hostap: Masashi Honma <masashi.honma at gmail.com>
Paul Stewart [Sun, 11 Nov 2012 09:18:31 +0000 (11:18 +0200)]
new_dbus_handlers: Clear errno
There are a few instances where dbus handlers test the value
of errno to test whether strtoul completes successfully.
Since strtoul does not clear errno, and there's no strong
reason to suspect that errno is already clear, it is safer
to clear it right before calling strtoul. Also, any failure
in strtoul (setting errno non-zero) should be considered a
failure.
While testing using dbus-send, I found that a malformed
network path can cause a crash due to net_id being left
NULL. We should test for this before calling strtoul
on it.
Jouni Malinen [Mon, 5 Nov 2012 15:05:37 +0000 (17:05 +0200)]
Remove unused wpa_supplicant_disassociate()
This function is now unused after the last couple of commits that
removed the last uses, so remove this to keep code simpler since all
places that disassociate, can use deauthentication instead.
Jouni Malinen [Mon, 5 Nov 2012 15:01:07 +0000 (17:01 +0200)]
Use deauthentication instead of disassociation on RSN element mismatch
Even though the standard currently describes disassociation to be used
for RSN element mismatch between Beacon/Probe Response frames and
EAPOL-Key msg 3/4, this is unnecessary difference from other cases that
deauthenticate. In addition, there is no point in leaving the 802.11
Authentication in place in this case. To keep things simpler, use
deauthentication here to get rid of the only use of
wpa_sm_disassociate().
Jouni Malinen [Mon, 5 Nov 2012 14:55:30 +0000 (16:55 +0200)]
Use deauthentication instead of disassociation if not associated
cfg80211/mac80211 may reject disassociation command if association has
not yet been formed. Use deauthentication in cases where it is possible
that we are associating at the moment the command is issued.
Jouni Malinen [Mon, 5 Nov 2012 14:42:28 +0000 (16:42 +0200)]
Use wpa_drv_{disassociate,deauthenticate} while waiting for connection
wpa_supplicant_{disassociate,deauthenticate}() need to inform the driver
about decision to disconnect even if this happens during the time when
the driver is still trying to complete association. During that time,
wpa_s->bssid is not set, so the code in these functions needs to figure
out the correct BSSID based on that field or wpa_s->pending_bssid. In
addition, it is possible that the BSSID is not even known at
wpa_supplicant at this point in time when using drivers that perform BSS
selection internally. In those cases, the disconnect command needs to be
sent to the driver without the BSSID.
This fixes issues where the driver (or cfg80211 in particular) may be
left in mismatching state with wpa_supplicant when disconnection (e.g.,
due to a ctrl_iface command) happens between connection request and
association event.
Jouni Malinen [Sat, 3 Nov 2012 11:50:17 +0000 (13:50 +0200)]
Handle assoc reject events without wpa_supplicant SME
If the driver indicates the association (or authentication) was
rejected, wpa_supplicant should handle this connection failure similarly
to other cases. Previously, this was only handled with drivers that use
wpa_supplicant SME.
In case of cfg80211-based drivers, a rejected association was actually
already handled since cfg80211 generates a deauthentication event after
indicating connection failure. However, rejected authentication resulted
in wpa_supplicant waiting for authentication timeout to expire which is
unnecessary long wait.
Fix this by calling wpas_connection_failed() to use the common mechanism
to reschedule a new connection attempt with the previously attempted
BSSID blacklisted.
Jouni Malinen [Thu, 1 Nov 2012 14:30:35 +0000 (16:30 +0200)]
WPS: Reject invalid credential more cleanly
If WPS Registrar tries to provision a WPA/WPA2-Personal network without
including a valid Network Key, the network block cannot be used to
connect to the network. Reject such credential without adding the
network block. This makes wpa_supplicant send WSC_NACK as a response to
the invalid Credential and stop the provisioning process immediately
rather than only after trying unsuccessfully to connect to the network.
Jouni Malinen [Wed, 31 Oct 2012 16:25:30 +0000 (18:25 +0200)]
P2P: Relax Bonjour SD query matching
The DNS Name is allowed to use or not use domain name compression. To
handle both cases, check human readable DNS Name match if binary
matching does not show a hit.
Jouni Malinen [Wed, 31 Oct 2012 11:01:43 +0000 (13:01 +0200)]
P2P: Support multiple P2P SD Bonjour services with same key
There may be multiple Bonjour PTR matches for the same key, so extend
the P2P SD code for this to allow such entries to be added (i.e., do not
override previously added value, but add a new one). Similarly, return
multiple matches (one per Service TLV) for a query if it happens to
match more than a single configured Bonjour service.
Jouni Malinen [Tue, 30 Oct 2012 13:12:04 +0000 (15:12 +0200)]
P2P: Allow discoverable interval for p2p_find to be configured
The new P2P_SET parameter disc_int can now be used to configure
discoverable interval for p2p_find operations. The format of the command
for setting the values is "P2P_SET disc_int <minDiscoverableInterval>
<maxDiscoverableInterval> <max TUs for discoverable interval>". The
first two parameters are given in units of 100 TUs (102.4 ms). The third
parameter can be used to further limit the interval into a specific TU
amount. If it is set to -1, no such additional limitation is enforced.
It should be noted that the P2P specification describes the random
Listen state interval to be in units of 100 TUs, so setting the max TU
value to anything else than -1 is not compliant with the specification
and should not be used in normal cases. The default parameters can be
set with "P2P_SET disc_int 1 3 -1".
Jouni Malinen [Tue, 30 Oct 2012 10:27:05 +0000 (12:27 +0200)]
Restore wpa_s->scan_req if scan trigger fails
If the driver rejects the scan request while handling an external
requested scan (e.g., SCAN command on ctrl_iface), wpa_s->scan_req gets
cleared in wpa_supplicant_scan(). This can results in issues when the
scheduled re-try of the scan in one seconds trigger another call to this
function. If ap_scan==2 mode is used, this would result in new
association attempt instead of a new scan. Avoid this by restoring value
of wpa_s->scan_req in case the scan trigger fails and a new scan attempt
is scheduled.
Jouni Malinen [Mon, 29 Oct 2012 14:25:02 +0000 (16:25 +0200)]
P2P: Clear pending_pd_before_join on PD timeout
wpas_p2p_pd_before_join_timeout() needs to clear the
pending_pd_before_join flag to match other uses of this flag prior to
calling wpas_p2p_join_start(). Without this, the flag could be left set
which can cause following P2P operations to behave in unexpected ways.
Jouni Malinen [Mon, 29 Oct 2012 13:02:30 +0000 (15:02 +0200)]
P2P: Allow separate P2P group interface use to be disabled
The new p2p_no_group_iface=1 configuration parameter can now be used to
disable the default behavior of adding a separate interface for the P2P
group when driver support for concurrent interfaces is available.
Jouni Malinen [Sun, 28 Oct 2012 19:37:15 +0000 (21:37 +0200)]
P2P: Fix default p2p_group_idle timeout for P2P client role
Commit 0d30cc240fa36905b034dc9676f9d8da0ac18e56 forced
wpa_s->current_ssid to be cleared in wpa_supplicant_mark_disassoc()
which gets called from wpa_supplicant_event_disassoc(). This breaks the
P2P group idle mechanism for the case where p2p_group_idle is not set
(i.e., is the default 0) since wpas_p2p_group_idle_timeout() ignores the
timeout in that case if the interface is not recognized as a client
interface (which was based on wpa_s->current_ssid being set).
Fix this by making wpas_p2p_is_client() default to client case if
wpa_s->current_ssid is NULL. This is much more likely case since the P2P
GO mode operation would not really clear the pointer without explicit
request to disconnect.
Jouni Malinen [Sun, 28 Oct 2012 16:20:03 +0000 (18:20 +0200)]
WPS: Remove old OOB NFC interface
The old WPS interface for using NFC has no known deployments and even
the binary libraries referenced here are not easily available anymore.
Since the new interface for using NFC with WPS covers the same
functionality, remove the old implementation to clean up WPS
implementation.
Jouni Malinen [Sun, 28 Oct 2012 16:02:04 +0000 (18:02 +0200)]
WPS: Use AP Channel attribute in credential to speed up scan
When WPS is used with NFC connection handover, the AP may indicate its
operating channel within the credential information. Use this
informatiom, if present, to speed up the scan process.
Jouni Malinen [Sun, 28 Oct 2012 15:39:46 +0000 (17:39 +0200)]
WPS: Add preliminary NFC connection handover support for Enrollee
This commit adds new wpa_supplicant ctrl_iface commands to allow
external programs to go through NFC connection handover mechanism
with wpa_supplicant taking care of the WPS processing. This version
includes only the case where wpa_supplicant is operating as a
station/Enrollee.
Jouni Malinen [Sat, 27 Oct 2012 08:52:43 +0000 (11:52 +0300)]
Fix EAPOL supplicant port authorization with PMKSA caching
The previous eapol_sm_notify_cached() implementation forced the port
to be authorized when receiving EAPOL-Key msg 1/4 that included a
matching PMKID in cases when PMKSA caching is used. This is too early
since the port should really be authorized only after the PTK has been
configured which is the case when PMKSA caching is not used.
Fix this by using the EAPOL supplicant PAE state machine to go through
the AUTHENTICATING and AUTHENTICATED states instead of forcing a jump
to AUTHENTICATED without performing full state machine steps. This can
be achieved simply by marking eapSuccess TRUE at least with the current
version of EAP and EAPOL state machines (the earlier commits in this
function seemed to indicate that this may have not been that easy in
the older versions due to the hacks needed here).
This addresses an issue with nl80211-based driver interface when the
driver depends on the STA Authorized flag being used to prevent
unprotected frames from being accepted (both TX and RX) prior to PTK
configuration.