We can get here from blkdev_ioctl() -> blkpg_ioctl() -> add_partition()
with a user passed in partno value. If we pass in 0x7fffffff, the
new target in disk_expand_part_tbl() overflows the 'int' and we
access beyond the end of ptbl->part[] and even write to it when we
do the rcu_assign_pointer() to assign the new partition.
Currently we enable Exynos devices in the multi v7 defconfig, however, when
testing on my ODROID-U3, I noticed that USB was not working. Enabling this
option causes USB to work, which enables networking support as well since the
ODROID-U3 has networking on the USB bus.
[arnd] Support for odroid-u3 was added in 3.10, so it would be nice to
backport this fix at least that far.
Commit 7628083227b6bc4a7e33d7c381d7a4e558424b6b (usb: gadget: at91_udc:
prepare clk before calling enable) added clock preparation in interrupt
context. This is not allowed as it might sleep. Also setting the clock
rate is unsafe to call from there for the same reason. Move clock
preparation and setting clock rate into process context (at91udc_probe).
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that the NULL pointer dereference happens
when we uses g_audio driver. Since the g_audio driver will call
usb_ep_disable() in afunc_set_alt() before it calls usb_ep_enable(),
the uep->pipe of renesas usbhs driver will be NULL. So, this patch
adds a condition to avoid the oops.
It is critical that fetch_block() and handle_stripe_dirtying()
are consistent in their analysis of what needs to be loaded.
Otherwise raid5 can wait forever for a block that won't be loaded.
Currently when writing to a RAID5 that is resyncing, to a location
beyond the resync offset, handle_stripe_dirtying chooses a
reconstruct-write cycle, but fetch_block() assumes a
read-modify-write, and a lockup can happen.
So treat that case just like RAID6, just as we do in
handle_stripe_dirtying. RAID6 always does reconstruct-write.
This bug was introduced when the behaviour of handle_stripe_dirtying
was changed in 3.7, so the patch is suitable for any kernel since,
though it will need careful merging for some versions.
Fixes: a7854487cd7128a30a7f4f5259de9f67d5efb95f Reported-by: Henry Cai <henryplusplus@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stac_store_hints() does utterly wrong for masking the values for
gpio_dir and gpio_data, likely due to copy&paste errors. Fortunately,
this feature is used very rarely, so the impact must be really small.
Commit 897c329bc ("ALSA: usb: caiaq: check for cdev->n_streams > 1")
introduced a safety check to protect against bogus data provided by
devices. However, the n_streams variable is already divided by
CHANNELS_PER_STREAM, so the correct check is 'n_streams > 0'.
In olden times the snd_hda_param_read() function always set "*start_id"
but in 2007 we introduced a new return and it causes uninitialized data
bugs in a couple of the callers: print_codec_info() and
hdmi_parse_codec().
The Arcam rPAC seems to have the same problem - whenever anything
(alsamixer, udevd, 3.9+ kernel from 60af3d037eb8c, ..) attempts to
access mixer / control interface of the card, the firmware "locks up"
the entire device, resulting in
SNDRV_PCM_IOCTL_HW_PARAMS failed (-5): Input/output error
from alsa-lib.
Other operating systems can somehow read the mixer (there seems to be
playback volume/mute), but any manipulation is ignored by the device
(which has hardware volume controls).
In (6468276 i2c: designware: make SCL and SDA falling time
configurable) new device tree properties were added for setting the
falling time of SDA and SCL. The device tree bindings doc had a typo
in it: it forgot the "-ns" suffix for both properies in the prose of
the bindings.
I assume this is a typo because:
* The source code includes the "-ns"
* The example in the bindings includes the "-ns".
Fix the typo.
Signed-off-by: Doug Anderson <dianders@chromium.org> Fixes: 6468276b2206 ("i2c: designware: make SCL and SDA falling time configurable") Acked-by: Romain Baeriswyl <romain.baeriswyl@alitech.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`genwqe_user_vmap()` calls `get_user_pages_fast()` and if the return
value is less than the number of pages requested, it frees the pages and
returns an error (`-EFAULT`). However, it fails to consider a negative
error return value from `get_user_pages_fast()`. In that case, the test
`if (rc < m->nr_pages)` will be false (due to promotion of `rc` to a
large `unsigned int`) and the code will continue on to call
`genwqe_map_pages()` with an invalid list of page pointers. Fix it by
bailing out if `get_user_pages_fast()` returns a negative error value.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bus_find_device_by_name() acquires a device reference which is never
released. This results in an object leak, which on older kernels
results in failure to release all resources of PCI devices. libvirt
uses drivers_probe to re-attach devices to the host after assignment
and is therefore a common trigger for this leak.
In Linux 3.18 and below, GCC hoists the lsl instructions in the
pvclock code all the way to the beginning of __vdso_clock_gettime,
slowing the non-paravirt case significantly. For unknown reasons,
presumably related to the removal of a branch, the performance issue
is gone as of
e76b027e6408 x86,vdso: Use LSL unconditionally for vgetcpu
but I don't trust GCC enough to expect the problem to stay fixed.
There should be no correctness issue, because the __getcpu calls in
__vdso_vlock_gettime were never necessary in the first place.
Note to stable maintainers: In 3.18 and below, depending on
configuration, gcc 4.9.2 generates code like this:
This patch won't apply as is to any released kernel, but I'll send a
trivial backported version if needed.
[
Backported by Andy Lutomirski. Should apply to all affected
versions. This fixes a functionality bug as well as a performance
bug: buggy kernels can infinite loop in __vdso_clock_gettime on
affected compilers. See, for exammple:
The theory behind vdso randomization is that it's mapped at a random
offset above the top of the stack. To avoid wasting a page of
memory for an extra page table, the vdso isn't supposed to extend
past the lowest PMD into which it can fit. Other than that, the
address should be a uniformly distributed address that meets all of
the alignment requirements.
The current algorithm is buggy: the vdso has about a 50% probability
of being at the very end of a PMD. The current algorithm also has a
decent chance of failing outright due to incorrect handling of the
case where the top of the stack is near the top of its PMD.
This fixes the implementation. The paxtest estimate of vdso
"randomisation" improves from 11 bits to 18 bits. (Disclaimer: I
don't know what the paxtest code is actually calculating.)
It's worth noting that this algorithm is inherently biased: the vdso
is more likely to end up near the end of its PMD than near the
beginning. Ideally we would either nix the PMD sharing requirement
or jointly randomize the vdso and the stack to reduce the bias.
In the mean time, this is a considerable improvement with basically
no risk of compatibility issues, since the allowed outputs of the
algorithm are unchanged.
As an easy test, doing this:
for i in `seq 10000`
do grep -P vdso /proc/self/maps |cut -d- -f1
done |sort |uniq -d
used to produce lots of output (1445 lines on my most recent run).
A tiny subset looks like this:
ipte_unlock_siif uses cmpxchg to replace the in-memory data of the ipte
lock together with ACCESS_ONCE for the intial read.
union ipte_control {
unsigned long val;
struct {
unsigned long k : 1;
unsigned long kh : 31;
unsigned long kg : 32;
};
};
[...]
static void ipte_unlock_siif(struct kvm_vcpu *vcpu)
{
union ipte_control old, new, *ic;
ic = &vcpu->kvm->arch.sca->ipte_control;
do {
new = old = ACCESS_ONCE(*ic);
new.kh--;
if (!new.kh)
new.k = 0;
} while (cmpxchg(&ic->val, old.val, new.val) != old.val);
if (!new.kh)
wake_up(&vcpu->kvm->arch.ipte_wq);
}
The new value, is loaded twice from memory with gcc 4.7.2 of
fedora 18, despite the ACCESS_ONCE:
--->
l %r4,0(%r3) <--- load first 32 bit of lock (k and kh) in r4
alfi %r4,2147483647 <--- add -1 to r4
llgtr %r4,%r4 <--- zero out the sign bit of r4
lg %r1,0(%r3) <--- load all 64 bit of lock into new
lgr %r2,%r1 <--- load the same into old
risbg %r1,%r4,1,31,32 <--- shift and insert r4 into the bits 1-31 of
new
llihf %r4,2147483647
ngrk %r4,%r1,%r4
jne aa0 <ipte_unlock+0xf8>
nihh %r1,32767
lgr %r4,%r2
csg %r4,%r1,0(%r3)
cgr %r2,%r4
jne a70 <ipte_unlock+0xc8>
If the memory value changes between the first load (l) and the second
load (lg) we are broken. If that happens VCPU threads will hang
(unkillable) in handle_ipte_interlock.
Andreas Krebbel analyzed this and tracked it down to a compiler bug in
that version:
"while it is not that obvious the C99 standard basically forbids
duplicating the memory access also in that case. For an argumentation of
a similiar case please see:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=22278#c43
For the implementation-defined cases regarding volatile there are some
GCC-specific clarifications which can be found here:
https://gcc.gnu.org/onlinedocs/gcc/Volatiles.html#Volatiles
I've tracked down the problem with a reduced testcase. The problem was
that during a tree level optimization (SRA - scalar replacement of
aggregates) the volatile marker is lost. And an RTL level optimizer (CSE
- common subexpression elimination) then propagated the memory read into
its second use introducing another access to the memory location. So
indeed Christian's suspicion that the union access has something to do
with it is correct (since it triggered the SRA optimization).
This issue has been reported and fixed in the GCC 4.8 development cycle:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58145"
This patch replaces the ACCESS_ONCE scheme with a barrier() based scheme
that should work for all supported compilers.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
some control register changes will flush some aspects of the CPU, e.g.
POP explicitely mentions that for CR9-CR11 "TLBs may be cleared".
Instead of trying to be clever and only flush on specific CRs, let
play safe and flush on all lctl(g) as future machines might define
new bits in CRs. Load control intercept should not happen that often.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace is expecting non-compacted format for KVM_GET_XSAVE, but
struct xsave_struct might be using the compacted format. Convert
in order to preserve userspace ABI.
Likewise, userspace is passing non-compacted format for KVM_SET_XSAVE
but the kernel will pass it to XRSTORS, and we need to convert back.
Fixes: f31a9f7c71691569359fa7fb8b0acaa44bce0324 Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: H. Peter Anvin <hpa@linux.intel.com> Tested-by: Nadav Amit <namit@cs.technion.ac.il> Reviewed-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_xsave_addr is the API to access XSAVE states, and KVM would
like to use it. Export it.
Cc: x86@kernel.org Cc: H. Peter Anvin <hpa@linux.intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New Genius MousePen i608X devices have a new id 0x501a instead of the
old 0x5011 so add a new #define with "_2" appended and change required
places.
The remaining two checkpatch warnings about line length
being over 80 characters are present in the original files too and this
patch was made in the same style (no line break).
Just adding a new id and changing the required places should make the
new device work without any issues according to the bug report in the
following url.
This patch was made according to and fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=67111
Apple bluetooth wireless keyboard (sold in UK) has always reported zero
for battery strength no matter what condition the batteries are actually
in. With this patch applied (applying same quirk as other Apple
keyboards), the battery strength is now correctly reported.
When a hid driver that uses i2c-hid as transport is unloaded, the hid core
will call i2c_hid_stop() which releases all the buffers associated with the
device. This includes also the command buffer.
Now, when the i2c-hid driver itself is unloaded it tries to power down the
device by sending it PWR_SLEEP command. Since the command buffer is already
released we get following crash:
This is a static checker fix. We write some binary settings to the
sysfs file. One of the settings is the "->startup_profile". There
isn't any checking to make sure it fits into the
pyra->profile_settings[] array in the profile_activated() function.
I added a check to pyra_sysfs_write_settings() in both places because
I wasn't positive that the other callers were correct.
Before ->start() is called, bufsize size is set to HID_MIN_BUFFER_SIZE,
64 bytes. While processing the IRQ, we were asking to receive up to
wMaxInputLength bytes, which can be bigger than 64 bytes.
Later, when ->start is run, a proper bufsize will be calculated.
Given wMaxInputLength is said to be unreliable in other part of the
code, set to receive only what we can even if it results in truncated
reports.
Current driver uses a common buffer for reading reports either
synchronously in i2c_hid_get_raw_report() and asynchronously in
the interrupt handler.
There is race condition if an interrupt arrives immediately after
the report is received in i2c_hid_get_raw_report(); the common
buffer is modified by the interrupt handler with the new report
and then i2c_hid_get_raw_report() proceed using wrong data.
Fix it by using a separate buffers for synchronous reports.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
[Antonio Borneo: cleanup, rebase to v3.17, submit mainline] Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So here, wacom_open is called, and then wacom_resume is called by the
PM system. However, wacom_open already took the lock when wacom_resume
tries to get it. Freeze.
A little bit of history shows that this already happened in the past
- commit f6cd378372bf ("Input: wacom - fix runtime PM related deadlock"),
and the solution was to call first the PM function before taking the lock.
The lock was introduced in commit commit e722409445fb ("Input: wacom -
implement suspend and autosuspend") when the autosuspend feature has
been added. Given that usbhid already takes care of this very same
locking between suspend/resume, I think we can simply kill the lock
in open/close.
The lock is now used also with LEDs, so we can not remove it completely.
Reported-by: Hans Spath <inbox-546@hans-spath.de> Tested-by: Hans Spath <inbox-546@hans-spath.de> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is indeed because of an uninitialized kobject for blk_mq_ctx.
The blk_mq_ctx kobjects are initialized in blk_mq_sysfs_init(), but it
goes loop over hctx_for_each_ctx(), i.e. it initializes only for
online CPUs. Thus, when a CPU is hotplugged, the ctx for the newly
onlined CPU is registered without initialization.
This patch fixes the issue by initializing the all ctx kobjects
belonging to each queue.
What we need is the following two guarantees:
* Any thread that observes the effect of the test_and_set_bit() by
__bt_get_word() also observes the preceding addition of 'current'
to the appropriate wait list. This is guaranteed by the semantics
of the spin_unlock() operation performed by prepare_and_wait().
Hence the conversion of test_and_set_bit_lock() into
test_and_set_bit().
* The wait lists are examined by bt_clear() after the tag bit has
been cleared. clear_bit_unlock() guarantees that any thread that
observes that the bit has been cleared also observes the store
operations preceding clear_bit_unlock(). However,
clear_bit_unlock() does not prevent that the wait lists are examined
before that the tag bit is cleared. Hence the addition of a memory
barrier between clear_bit() and the wait list examination.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Robert Elliott <elliott@hp.com> Cc: Ming Lei <ming.lei@canonical.com> Cc: Alexander Gordeev <agordeev@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If __bt_get_word() is called with last_tag != 0, if the first
find_next_zero_bit() fails, if after wrap-around the
test_and_set_bit() call fails and find_next_zero_bit() succeeds,
if the next test_and_set_bit() call fails and subsequently
find_next_zero_bit() does not find a zero bit, then another
wrap-around will occur. Avoid this by introducing an additional
local variable.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Robert Elliott <elliott@hp.com> Cc: Ming Lei <ming.lei@canonical.com> Cc: Alexander Gordeev <agordeev@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
blk-mq users are allowed to free the memory request_queue.tag_set
points at after blk_cleanup_queue() has finished but before
blk_release_queue() has started. This can happen e.g. in the SCSI
core. The SCSI core namely embeds the tag_set structure in a SCSI
host structure. The SCSI host structure is freed by
scsi_host_dev_release(). This function is called after
blk_cleanup_queue() finished but can be called before
blk_release_queue().
This means that it is not safe to access request_queue.tag_set from
inside blk_release_queue(). Hence remove the blk_sync_queue() call
from blk_release_queue(). This call is not necessary - outstanding
requests must have finished before blk_release_queue() is
called. Additionally, move the blk_mq_free_queue() call from
blk_release_queue() to blk_cleanup_queue() to avoid that struct
request_queue.tag_set gets accessed after it has been freed.
This patch avoids that the following kernel oops can be triggered
when deleting a SCSI host for which scsi-mq was enabled:
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Robert Elliott <elliott@hp.com> Cc: Ming Lei <ming.lei@canonical.com> Cc: Alexander Gordeev <agordeev@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently use num_possible_cpus(), but that breaks on sparc64 where
the CPU ID space is discontig. Use nr_cpu_ids as the highest CPU ID
instead, so we don't end up reading from invalid memory.
Since commit 1196c2f a domain is only destroyed in the
notifier path if it is hot-unplugged. This caused a
domain leakage in iommu_attach_device when a driver was
unbound from the device and bound to VFIO. In this case the
device is attached to a new domain and unlinked from the old
domain. At this point nothing points to the old domain
anymore and its memory is leaked.
Fix this by explicitly freeing the old domain in
iommu_attach_domain.
Fixes: 1196c2f (iommu/vt-d: Fix dmar_domain leak in iommu_attach_device) Tested-by: Jerry Hoemann <jerry.hoemann@hp.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's an off-by-one bug in function __domain_mapping(), which may
trigger the BUG_ON(nr_pages < lvl_pages) when
(nr_pages + 1) & superpage_mask == 0
The issue was introduced by commit 9051aa0268dc "intel-iommu: Combine
domain_pfn_mapping() and domain_sg_mapping()", which sets sg_res to
"nr_pages + 1" to avoid some of the 'sg_res==0' code paths.
It's safe to remove extra "+1" because sg_res is only used to calculate
page size now.
Reported-And-Tested-by: Sudeep Dutt <sudeep.dutt@intel.com> Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Acked-By: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the erase worker is unable to erase a PEB it will
free the ubi_wl_entry itself.
The failing ubi_wl_entry must not free()'d again after
do_sync_erase() returns.
The logic of vfree()'ing vol->upd_buf is tied to vol->updating.
In ubi_start_update() vol->updating is set long before vmalloc()'ing
vol->upd_buf. If we encounter a write failure in ubi_start_update()
before vmalloc() the UBI device release function will try to vfree()
vol->upd_buf because vol->updating is set.
Fix this by allocating vol->upd_buf directly after setting vol->updating.
On some ARMs the memory can be mapped pgprot_noncached() and still
be working for atomic operations. As pointed out by Colin Cross
<ccross@android.com>, in some cases you do want to use
pgprot_noncached() if the SoC supports it to see a debug printk
just before a write hanging the system.
On ARMs, the atomic operations on strongly ordered memory are
implementation defined. So let's provide an optional kernel parameter
for configuring pgprot_noncached(), and use pgprot_writecombine() by
default.
Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robherring2@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Anton Vorontsov <anton@enomsg.org> Cc: Colin Cross <ccross@android.com> Cc: Olof Johansson <olof@lixom.net> Cc: Russell King <linux@arm.linux.org.uk> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently trying to use pstore on at least ARMs can hang as we're
mapping the peristent RAM with pgprot_noncached().
On ARMs, pgprot_noncached() will actually make the memory strongly
ordered, and as the atomic operations pstore uses are implementation
defined for strongly ordered memory, they may not work. So basically
atomic operations have undefined behavior on ARM for device or strongly
ordered memory types.
Let's fix the issue by using write-combine variants for mappings. This
corresponds to normal, non-cacheable memory on ARM. For many other
architectures, this change does not change the mapping type as by
default we have:
#define pgprot_writecombine pgprot_noncached
The reason why pgprot_noncached() was originaly used for pstore
is because Colin Cross <ccross@android.com> had observed lost
debug prints right before a device hanging write operation on some
systems. For the platforms supporting pgprot_noncached(), we can
add a an optional configuration option to support that. But let's
get pstore working first before adding new features.
Cc: Arnd Bergmann <arnd@arndb.de> Cc: Anton Vorontsov <cbouatmailru@gmail.com> Cc: Colin Cross <ccross@android.com> Cc: Olof Johansson <olof@lixom.net> Cc: linux-kernel@vger.kernel.org Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
[tony@atomide.com: updated description] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6ac665c63dca ("PCI: rewrite PCI BAR reading code") masked off
low-order bits from 'l', but not from 'sz'. Both are passed to pci_size(),
which compares 'base == maxbase' to check for read-only BARs. The masking
of 'l' means that comparison will never be 'true', so the check for
read-only BARs no longer works.
Resolve this by also masking off the low-order bits of 'sz' before passing
it into pci_size() as 'maxbase'. With this change, pci_size() will once
again catch the problems that have been encountered to date:
- AGP aperture BAR of AMD-7xx host bridges: if the AGP window is
disabled, this BAR is read-only and read as 0x00000008 [1]
- BARs 0-4 of ALi IDE controllers can be non-zero and read-only [1]
When connectable mode is enabled (page scan on) through some non-mgmt
method the HCI_CONNECTABLE flag will not be set. For backwards
compatibility with user space versions not using mgmt we should not
require HCI_CONNECTABLE to be set if HCI_MGMT is not set.
When controllers set the HCI_QUIRK_INVALID_BDADDR flag, it is required
by userspace to program a valid public Bluetooth device address into
the controller before it can be used.
After successful address configuration, the internal state changes and
the controller runs the complete initialization procedure. However one
small difference is that this is no longer the HCI_SETUP stage. The
HCI_SETUP stage is only valid during initial controller setup. In this
case the stack runs the initialization as part of the HCI_CONFIG stage.
The controller version information, default name and supported commands
are only stored during HCI_SETUP. While these information are static,
they are not read initially when HCI_QUIRK_INVALID_BDADDR is set. So
when running in HCI_CONFIG state, these information need to be updated
as well.
This especially impacts Bluetooth 4.1 and later controllers using
extended feature pages and second event mask page.
The internal representation of the LE white list needs to be cleared
when receiving a successful HCI_Reset command. A reset of the controller
is expected to start with an empty LE white list.
When the LE white list is not cleared on controller reset, the passive
background scanning might skip programming the remote devices. Only
changes to the LE white list are programmed when passive background
is started.
These days we allow simultaneous LE scanning and advertising. Checking
for whether advertising is enabled or not is therefore not a reliable
way to determine whether directed advertising was used to trigger the
connection creation. The appropriate place to check (instead of the hdev
context) is the connection role that's stored in the hci_conn. This
patch fixes such a check in le_conn_timeout() which could otherwise lead
to incorrect HCI commands being sent.
The le_conn_timeout() may call hci_le_conn_failed() which in turn may
call hci_conn_del(). Trying to use the _sync variant for cancelling the
conn timeout from hci_conn_del() could therefore result in a deadlock.
This patch converts hci_conn_del() to use the non-sync variant so the
deadlock is not possible.
Since both ppc and ppc64 have LE variants which are now reported by uname, add
that flag (__AUDIT_ARCH_LE) to syscall_get_arch() and add AUDIT_ARCH_PPC64LE
variant.
Without this, perf trace and auditctl fail.
Mainline kernel reports ppc64le (per a058801) but there is no matching
AUDIT_ARCH_PPC64LE.
Since 32-bit PPC LE is not supported by audit, don't advertise it in
AUDIT_ARCH_PPC* variants.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com> Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 24x7 counters are continuously running and not updated on an
interrupt. So we record the event counts when stopping the event or
deleting it.
But to "read" a single counter in 24x7, we allocate a page and pass it
into the hypervisor (The HV returns the page full of counters from which
we extract the specific counter for this event).
We allocate a page using GFP_USER and when deleting the event, we end up
with the following warning because we are blocking in interrupt context.
[ 698.641709] BUG: scheduling while atomic: swapper/0/0/0x10010000
We could use GFP_ATOMIC but that could result in failures. Pre-allocate
a buffer so we don't have to allocate in interrupt context. Further as
Michael Ellerman suggested, use Per-CPU buffer so we only need to
allocate once per CPU.
Currently, when going idle, we set the flag indicating that we are in
nap mode (paca->kvm_hstate.hwthread_state) and then execute the nap
(or sleep or rvwinkle) instruction, all with the MMU on. This is bad
for two reasons: (a) the architecture specifies that those instructions
must be executed with the MMU off, and in fact with only the SF, HV, ME
and possibly RI bits set, and (b) this introduces a race, because as
soon as we set the flag, another thread can switch the MMU to a guest
context. If the race is lost, this thread will typically start looping
on relocation-on ISIs at 0xc...4400.
This fixes it by setting the MSR as required by the architecture before
setting the flag or executing the nap/sleep/rvwinkle instruction.
[ shreyas@linux.vnet.ibm.com: Edited to handle LE ] Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing MCE code calls flush_tlb hook with IS=0 (single page) resulting
in partial invalidation of TLBs which is not right. This patch fixes
that by passing IS=0xc00 to invalidate whole TLB for successful recovery
from TLB and ERAT errors.
We have some code in udbg_uart_getc_poll() that tries to protect
against a NULL udbg_uart_in, but gets it all wrong.
Found with the LLVM static analyzer (scan-build).
Fixes: 309257484cc1 ("powerpc: Cleanup udbg_16550 and add support for LPC PIO-only UARTs") Signed-off-by: Anton Blanchard <anton@samba.org>
[mpe: Add some newlines for readability while we're here] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6071c22e1755 "ktest: Rewrite the config-bisect to actually work"
fixed the config-bisect to work nicely but in doing so it broke
make_min_config by changing the way assign_configs works.
The assign_configs function now adds the config to the hash even if
it is disabled, but changes the hash value to be that of the
line "# CONFIG_FOO is not set". Unfortunately, the make_min_config
test only checks to see if the config is removed. It now needs to
check if the config is in the hash and not set to be disabled.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flush the FIFOs when the stream is prepared for use. This avoids
an inadvertent swapping of the left/right channels if the FIFOs are
not empty at startup.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the codec is connected using i2c, it will only auto-increment
register addresses if msb (0x80) of the register address byte is set.
[Fixes cache sync if multiple adjacent registers are updated -- broonie]
Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5fe5b767dc6f ("ASoC: dapm: Do not pretend to support controls for non
mixer/mux widgets") revealed ill-defined control in a route between
"STENL Mux" and DACs in max98090.c:
max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACL
max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACL
max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACL
max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACR
max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACR
max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACR
Since there is no control between "STENL Mux" and DACs the control name must
be NULL not "NULL".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the version field of the firmware header to make sure to
not accidentally try to parse a firmware file with a different layout.
Trying to do so can result in loading invalid firmware code to the device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The of_node_put() call in eukrea_tlv320_probe() may take an
uninitialized pointer, as compiler spotted out:
sound/soc/fsl/eukrea-tlv320.c:221:14: warning: 'ssi_np' may be used uninitialized in this function [-Wuninitialized]
This patch adds the proper NULL initializations as a fix.
(codec_np is also NULL initialized just for consistency.)
Fixes: 66f232908de2 ('ASoC: eukrea-tlv320: Add DT support') Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like with ath9k, ath5k queues also need to be ordered by priority.
queue_info->tqi_subtype already contains the correct index, so use it
instead of relying on the order of ath5k_hw_setup_tx_queue calls.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the commit below, iwldvm sends the FLUSH command to
the firmware. All the devices that use iwldvm have a
firmware that expects the _v3 version of this command,
besides 5150.
5150's latest available firmware still expects a _v2 version
of the FLUSH command.
This means that since the commit below, we had a mismatch for
this specific device only.
This mismatch led to the NMI below:
This was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=88961
Fixes: a0855054e59b ("iwlwifi: dvm: drop non VO frames when flushing") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On x86 truncation cannot occur because config XEN depends on X86_64 ||
(X86_32 && X86_PAE).
On ARM truncation can occur without CONFIG_ARM_LPAE, when the dma
operation involves foreign grants. However in that case the physical
address returned by xen_bus_to_phys is actually invalid (there is no mfn
to pfn tracking for foreign grants on ARM) and it is not used.
This patchs fixes a misplaced call to memset() that fills the request
buffer with 0. The problem was with sending PCAN_USBPRO_REQ_FCT
requests, the content set by the caller was thus lost.
With this patch, the memory area is zeroed only when requesting info
from the device.
This patch sets the correct reverse sequence order to the instructions
set to run, when any failure occurs during the initialization steps.
It also adds the missing unregistration call of the can device if the
failure appears after having been registered.
Hardware queues are ordered by priority. Use queue index 0 for BK, which
has lower priority than BE.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver passes the desired hardware queue index for a WMM data queue
in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which
instead relied on the order in which the function is called.
Reported-by: Hubert Feurstein <h.feurstein@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ocfs2_link(), the parent directory inode passed to function
ocfs2_lookup_ino_from_name() is wrong. Parameter dir is the parent of
new_dentry not old_dentry. We should get old_dir from old_dentry and
lookup old_dentry in old_dir in case another node remove the old dentry.
With this change, hard linking works again, when paths are relative with
at least one subdirectory. This is how the problem was reproducable:
# mkdir a
# mkdir b
# touch a/test
# ln a/test b/test
ln: failed to create hard link `b/test' => `a/test': No such file or directory
However when creating links in the same dir, it worked well.
Now the link gets created.
Fixes: 0e048316ff57 ("ocfs2: check existence of old dentry in ocfs2_link()") Signed-off-by: joyce.xue <xuejiufei@huawei.com> Reported-by: Szabo Aron - UBIT <aron@ubit.hu> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Tested-by: Aron Szabo <aron@ubit.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For buffer write, page lock will be got in write_begin and released in
write_end, in ocfs2_write_end_nolock(), before it unlock the page in
ocfs2_free_write_ctxt(), it calls ocfs2_run_deallocs(), this will ask
for the read lock of journal->j_trans_barrier. Holding page lock and
ask for journal->j_trans_barrier breaks the locking order.
This will cause a deadlock with journal commit threads, ocfs2cmt will
get write lock of journal->j_trans_barrier first, then it wakes up
kjournald2 to do the commit work, at last it waits until done. To
commit journal, kjournald2 needs flushing data first, it needs get the
cache page lock.
Since some ocfs2 cluster locks are holding by write process, this
deadlock may hung the whole cluster.
unlock pages before ocfs2_run_deallocs() can fix the locking order, also
put unlock before ocfs2_commit_trans() to make page lock is unlocked
before j_trans_barrier to preserve unlocking order.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Wengang Wang <wen.gang.wang@oracle.com> Reviewed-by: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Intersil ISL12057 support was added by commit 70e123373c05 ("rtc: Add
support for Intersil ISL12057 I2C RTC chip"), two masks for time registers
values imported from the device were either wrong or omitted, leading to
additional bits from those registers to impact read values:
- mask for hour register value when reading it in AM/PM mode. As
AM/PM mode is not the usual mode used by the driver, this error
would only have an impact on an externally configured RTC hour
later read by the driver.
- mask for month value. The lack of masking would provide an
erroneous value if century bit is set.
This patch fixes those two masks.
Fixes: 70e123373c05 ("rtc: Add support for Intersil ISL12057 I2C RTC chip") Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Mark Brown <broonie@kernel.org> Cc: Grant Likely <grant.likely@linaro.org> Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This series fixes a few issues with the omap rtc-driver, cleans up a
bit, adds device abstraction, and finally adds support for the PMIC
control feature found in some revisions of this RTC IP block.
Ultimately, this allows for powering off the Beaglebone and waking it up
again on RTC alarms.
This patch (of 20):
Make sure not to reset the clock-source configuration when enabling the
32kHz clock mux.
Until the clock source can be configured through device tree we must not
overwrite settings made by the bootloader (e.g. clock-source
selection).
Fixes: cd914bba03d8 ("drivers/rtc/rtc-omap.c: add support for enabling 32khz clock") Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Felipe Balbi <balbi@ti.com> Tested-by: Felipe Balbi <balbi@ti.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Tony Lindgren <tony@atomide.com> Cc: Benot Cousson <bcousson@baylibre.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Cc: Keerthy J <j-keerthy@ti.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move rtc register to be later than hardware initialization. The reason
is that devm_rtc_device_register() will do read_time() which is a
callback accessing hardware. This sometimes causes a hang in the
hardware related callback.
Signed-off-by: Guo Zeng <guo.zeng@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we abort a transaction we iterate over all the ranges marked as dirty
in fs_info->freed_extents[0] and fs_info->freed_extents[1], clear them
from those trees, add them back (unpin) to the free space caches and, if
the fs was mounted with "-o discard", perform a discard on those regions.
Also, after adding the regions to the free space caches, a fitrim ioctl call
can see those ranges in a block group's free space cache and perform a discard
on the ranges, so the same issue can happen without "-o discard" as well.
This causes corruption, affecting one or multiple btree nodes (in the worst
case leaving the fs unmountable) because some of those ranges (the ones in
the fs_info->pinned_extents tree) correspond to btree nodes/leafs that are
referred by the last committed super block - breaking the rule that anything
that was committed by a transaction is untouched until the next transaction
commits successfully.
I ran into this while running in a loop (for several hours) the fstest that
I recently submitted:
[PATCH] fstests: add btrfs test to stress chunk allocation/removal and fstrim
The corruption always happened when a transaction aborted and then fsck complained
like this:
_check_btrfs_filesystem: filesystem on /dev/sdc is inconsistent
*** fsck.btrfs output ***
Check tree block failed, want=94945280, have=0
Check tree block failed, want=94945280, have=0
Check tree block failed, want=94945280, have=0
Check tree block failed, want=94945280, have=0
Check tree block failed, want=94945280, have=0
read block failed check_tree_block
Couldn't open file system
In this case 94945280 corresponded to the root of a tree.
Using frace what I observed was the following sequence of steps happened:
1) transaction N started, fs_info->pinned_extents pointed to
fs_info->freed_extents[0];
4) transaction N commit starts, fs_info->pinned_extents now points to
fs_info->freed_extents[1], and transaction N completes;
5) transaction N + 1 starts;
6) eb is COWed, and btrfs_free_tree_block() called for this eb;
7) eb range (94945280 to 94945280 + 16Kb) is added to
fs_info->pinned_extents (fs_info->freed_extents[1]);
8) Something goes wrong in transaction N + 1, like hitting ENOSPC
for example, and the transaction is aborted, turning the fs into
readonly mode. The stack trace I got for example:
[112065.253935] [<ffffffff8140c7b6>] dump_stack+0x4d/0x66
[112065.254271] [<ffffffff81042984>] warn_slowpath_common+0x7f/0x98
[112065.254567] [<ffffffffa0325990>] ? __btrfs_abort_transaction+0x50/0x10b [btrfs]
[112065.261674] [<ffffffff810429e5>] warn_slowpath_fmt+0x48/0x50
[112065.261922] [<ffffffffa032949e>] ? btrfs_free_path+0x26/0x29 [btrfs]
[112065.262211] [<ffffffffa0325990>] __btrfs_abort_transaction+0x50/0x10b [btrfs]
[112065.262545] [<ffffffffa036b1d6>] btrfs_remove_chunk+0x537/0x58b [btrfs]
[112065.262771] [<ffffffffa033840f>] btrfs_delete_unused_bgs+0x1de/0x21b [btrfs]
[112065.263105] [<ffffffffa0343106>] cleaner_kthread+0x100/0x12f [btrfs]
(...)
[112065.264493] ---[ end trace dd7903a975a31a08 ]---
[112065.264673] BTRFS: error (device sdc) in btrfs_remove_chunk:2625: errno=-28 No space left
[112065.264997] BTRFS info (device sdc): forced readonly
9) The clear kthread sees that the BTRFS_FS_STATE_ERROR bit is set in
fs_info->fs_state and calls btrfs_cleanup_transaction(), which in
turn calls btrfs_destroy_pinned_extent();
10) Then btrfs_destroy_pinned_extent() iterates over all the ranges
marked as dirty in fs_info->freed_extents[], and for each one
it calls discard, if the fs was mounted with "-o discard", and
adds the range to the free space cache of the respective block
group;
11) btrfs_trim_block_group(), invoked from the fitrim ioctl code path,
sees the free space entries and performs a discard;
12) After an umount and mount (or fsck), our eb's location on disk was full
of zeroes, and it should have been untouched, because it was marked as
dirty in the fs_info->pinned_extents tree, and therefore used by the
trees that the last committed superblock points to.
Fix this by not performing a discard and not adding the ranges to the free space
caches - it's useless from this point since the fs is now in readonly mode and
we won't write free space caches to disk anymore (otherwise we would leak space)
nor any new superblock. By not adding the ranges to the free space caches, it
prevents other code paths from allocating that space and write to it as well,
therefore being safer and simpler.
Liu Bo pointed out that my previous fix would lose the generation update in the
scenario I described. It is actually much worse than that, we could lose the
entire extent if we lose power right after the transaction commits. Consider
the following
write extent 0-4k
log extent in log tree
commit transaction
< power fail happens here
ordered extent completes
We would lose the 0-4k extent because it hasn't updated the actual fs tree, and
the transaction commit will reset the log so it isn't replayed. If we lose
power before the transaction commit we are save, otherwise we are not.
Fix this by keeping track of all extents we logged in this transaction. Then
when we go to commit the transaction make sure we wait for all of those ordered
extents to complete before proceeding. This will make sure that if we lose
power after the transaction commit we still have our data. This also fixes the
problem of the improperly updated extent generation. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use the modified list to keep track of which extents have been modified so we
know which ones are candidates for logging at fsync() time. Newly modified
extents are added to the list at modification time, around the same time the
ordered extent is created. We do this so that we don't have to wait for ordered
extents to complete before we know what we need to log. The problem is when
something like this happens
log extent 0-4k on inode 1
copy csum for 0-4k from ordered extent into log
sync log
commit transaction
log some other extent on inode 1
ordered extent for 0-4k completes and adds itself onto modified list again
log changed extents
see ordered extent for 0-4k has already been logged
at this point we assume the csum has been copied
sync log
crash
On replay we will see the extent 0-4k in the log, drop the original 0-4k extent
which is the same one that we are replaying which also drops the csum, and then
we won't find the csum in the log for that bytenr. This of course causes us to
have errors about not having csums for certain ranges of our inode. So remove
the modified list manipulation in unpin_extent_cache, any modified extents
should have been added well before now, and we don't want them re-logged. This
fixes my test that I could reliably reproduce this problem with. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sizes that are obtained from space infos are in raw units and have
to be adjusted according to the raid factor. This was missing for
f_bavail and df reported doubled size for raid1.
Reported-by: Martin Steigerwald <Martin@lichtvoll.de> Fixes: ba7b6e62f420 ("btrfs: adjust statfs calculations according to raid profiles") Signed-off-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we have two fsync()'s race on different subvols one will do all of its work
to get into the log_tree, wait on it's outstanding IO, and then allow the
log_tree to finish it's commit. The problem is we were just free'ing that
subvols logged extents instead of waiting on them, so whoever lost the race
wouldn't really have their data on disk. Fix this by waiting properly instead
of freeing the logged extents. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Chernenkov used KASAN to discover that eCryptfs writes past the
end of the allocated buffer during encrypted filename decoding. This
fix corrects the issue by getting rid of the unnecessary 0 write when
the current bit offset is 2.
The ecryptfs_encrypted_view mount option greatly changes the
functionality of an eCryptfs mount. Instead of encrypting and decrypting
lower files, it provides a unified view of the encrypted files in the
lower filesystem. The presence of the ecryptfs_encrypted_view mount
option is intended to force a read-only mount and modifying files is not
supported when the feature is in use. See the following commit for more
information:
This patch forces the mount to be read-only when the
ecryptfs_encrypted_view mount option is specified by setting the
MS_RDONLY flag on the superblock. Additionally, this patch removes some
broken logic in ecryptfs_open() that attempted to prevent modifications
of files when the encrypted view feature was in use. The check in
ecryptfs_open() was not sufficient to prevent file modifications using
system calls that do not operate on a file descriptor.
Check that length specified in a component of a symlink fits in the
input buffer we are reading. Also properly ignore component length for
component types that do not use it. Otherwise we read memory after end
of buffer for corrupted udf image.
Reported-by: Carl Henrik Lunde <chlunde@ping.uio.no> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / people / ms / linux.git / log
