The reference to iloc.bh has been dropped in ext4_mark_iloc_dirty.
However, the reference is dropped again if error occurs during
ext4_handle_dirty_metadata, which may result in use-after-free bugs.
Fixes: fb265c9cb49e("ext4: add ext4_sb_bread() to disambiguate ENOMEM cases") Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In other places in fs/ext4/xattr.c, if e_value_inum is non-zero, the
code ignores the value in e_value_offs. The e_value_offs *should* be
zero, but we shouldn't depend upon it, since it might not be true in a
corrupted/fuzzed file system.
The sanity check in mb_find_extent() only checked that returned extent
does not extend past blocksize * 8, however it should not extend past
EXT4_CLUSTERS_PER_GROUP(sb). This can happen when clusters_per_group <
blocksize * 8 and the tail of the bitmap is not properly filled by 1s
which happened e.g. when ancient kernels have grown the filesystem.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We hit a BUG at fs/buffer.c:3057 if we detached the nbd device
before unmounting ext4 filesystem.
The typical chain of events leading to the BUG:
jbd2_write_superblock
submit_bh
submit_bh_wbc
BUG_ON(!buffer_mapped(bh));
The block device is removed and all the pages are invalidated. JBD2
was trying to write journal superblock to the block device which is
no longer present.
Fix this by checking the journal superblock's buffer head prior to
submitting.
Reported-by: Eric Ren <renzhen@linux.alibaba.com> Signed-off-by: Jiufei Xue <jiufei.xue@linux.alibaba.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug manifests on systemd systems with multiple vtcon devices:
# cat /sys/devices/virtual/vtconsole/vtcon0/name
(S) dummy device
# cat /sys/devices/virtual/vtconsole/vtcon1/name
(M) frame buffer device
There systemd runs 'loadkeys' tool in tapallel for each vtcon
instance. This causes two parallel ioctl(KDSKBSENT) calls to
race into adding the same entry into 'func_table' array at:
drivers/tty/vt/keyboard.c:vt_do_kdgkb_ioctl()
The function has no locking around writes to 'func_table'.
The simplest reproducer is to have initrams with the following
init on a 8-CPU machine x86_64:
Previously, in the userspace, it was possible to use the "setterm" command
from util-linux to blank the VT console by default, using the following
command.
According to the man page,
> The force option keeps the screen blank even if a key is pressed.
It was implemented by calling TIOCL_BLANKSCREEN.
case BLANKSCREEN:
ioctlarg = TIOCL_BLANKSCREEN;
if (ioctl(STDIN_FILENO, TIOCLINUX, &ioctlarg))
warn(_("cannot force blank"));
break;
However, after Linux 4.12, this command ceased to work anymore, which is
unexpected. By inspecting the kernel source, it shows that the issue was
triggered by the side-effect from commit a4199f5eb809 ("tty: Disable
default console blanking interval").
The console blanking is implemented by function do_blank_screen() in vt.c:
"blank_state" will be initialized to "blank_normal_wait" in con_init() if
AND ONLY IF ("blankinterval" > 0). If "blankinterval" is 0, "blank_state"
will be "blank_off" (== 0), and a call to do_blank_screen() will always
abort, even if a forced blanking is required from the user by calling
TIOCL_BLANKSCREEN, the console won't be blanked.
This behavior is unexpected from a user's point-of-view, since it's not
mentioned in any documentation. The setterm man page suggests it will
always work, and the kernel comments in uapi/linux/tiocl.h says
> /* keep screen blank even if a key is pressed */
> #define TIOCL_BLANKSCREEN 14
To fix it, we simply remove the "blank_state != blank_off" check, as
pointed out by Nicolas Pitre, this check doesn't logically make sense
and it's safe to remove.
It was observed that reads crossing 4K address boundary are failing.
This limitation is mentioned in Intel documents:
Intel(R) 9 Series Chipset Family Platform Controller Hub (PCH) Datasheet:
"5.26.3 Flash Access
Program Register Access:
* Program Register Accesses are not allowed to cross a 4 KB boundary..."
Enhanced Serial Peripheral Interface (eSPI)
Interface Base Specification (for Client and Server Platforms):
"5.1.4 Address
For other memory transactions, the address may start or end at any byte
boundary. However, the address and payload length combination must not
cross the naturally aligned address boundary of the corresponding Maximum
Payload Size. It must not cross a 4 KB address boundary."
Avoid this by splitting an operation crossing the boundary into two
operations.
Fixes: 8afda8b26d01 ("spi-nor: Add support for Intel SPI serial flash controller") Cc: stable@vger.kernel.org Reported-by: Romain Porte <romain.porte@nokia.com> Tested-by: Pascal Fabreges <pascal.fabreges@nokia.com> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mismatch between what is found in the Datasheets for DA9063 and DA9063L
provided by Dialog Semiconductor, and the register names provided in the
MFD registers file. The changes are for the OTP (one-time-programming)
control registers. The two naming errors are OPT instead of OTP, and
COUNT instead of CONT (i.e. control).
Cc: Stable <stable@vger.kernel.org> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed that recently multiple systems (chromebooks) couldn't wake
from S0ix using LID or Keyboard after updating to a newer kernel. I
bisected and it turned up commit f941d3e41da7 ("ACPI: EC / PM: Disable
non-wakeup GPEs for suspend-to-idle"). I checked that the issue got
fixed if that commit was reverted.
I debugged and found that although PNP0C0D:00 (representing the LID)
is wake capable and should wakeup the system per the code in
acpi_wakeup_gpe_init() and in drivers/acpi/button.c:
On debugging, I found that its corresponding GPE is not being enabled.
The particular GPE's "gpe_register_info->enable_for_wake" does not
have any bits set when acpi_enable_all_wakeup_gpes() comes around to
use it. I looked at code and could not find any other code path that
should set the bits in "enable_for_wake" bitmask for the wake enabled
devices for s2idle. [I do see that it happens for S3 in
acpi_sleep_prepare()].
Thus I used the same call to enable the GPEs for wake enabled devices,
and verified that this fixes the regression I was seeing on multiple
of my devices.
[ rjw: The problem is that commit f941d3e41da7 ("ACPI: EC / PM:
Disable non-wakeup GPEs for suspend-to-idle") forgot to add
the acpi_enable_wakeup_devices() call for s2idle along with
acpi_enable_all_wakeup_gpes(). ]
Fixes: f941d3e41da7 ("ACPI: EC / PM: Disable non-wakeup GPEs for suspend-to-idle") Link: https://bugzilla.kernel.org/show_bug.cgi?id=203579 Signed-off-by: Rajat Jain <rajatja@google.com>
[ rjw: Subject & changelog ] Cc: 5.0+ <stable@vger.kernel.org> # 5.0+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The task structure is freed while get_mem_cgroup_from_mm() holds
rcu_read_lock() and dereferences mm->owner.
get_mem_cgroup_from_mm() failing fork()
---- ---
task = mm->owner
mm->owner = NULL;
free(task)
if (task) *task; /* use after free */
The fix consists in freeing the task with RCU also in the fork failure
case, exactly like it always happens for the regular exit(2) path. That
is enough to make the rcu_read_lock hold in get_mem_cgroup_from_mm()
(left side above) effective to avoid a use after free when dereferencing
the task structure.
An alternate possible fix would be to defer the delivery of the
userfaultfd contexts to the monitor until after fork() is guaranteed to
succeed. Such a change would require more changes because it would
create a strict ordering dependency where the uffd methods would need to
be called beyond the last potentially failing branch in order to be
safe. This solution as opposed only adds the dependency to common code
to set mm->owner to NULL and to free the task struct that was pointed by
mm->owner with RCU, if fork ends up failing. The userfaultfd methods
can still be called anywhere during the fork runtime and the monitor
will keep discarding orphaned "mm" coming from failed forks in userland.
This race condition couldn't trigger if CONFIG_MEMCG was set =n at build
time.
[aarcange@redhat.com: improve changelog, reduce #ifdefs per Michal] Link: http://lkml.kernel.org/r/20190429035752.4508-1-aarcange@redhat.com Link: http://lkml.kernel.org/r/20190325225636.11635-2-aarcange@redhat.com Fixes: 893e26e61d04 ("userfaultfd: non-cooperative: Add fork() event") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Tested-by: zhong jiang <zhongjiang@huawei.com> Reported-by: syzbot+cbb52e396df3e565ab02@syzkaller.appspotmail.com Cc: Oleg Nesterov <oleg@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Peter Xu <peterx@redhat.com> Cc: Jason Gunthorpe <jgg@mellanox.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: zhong jiang <zhongjiang@huawei.com> Cc: syzbot+cbb52e396df3e565ab02@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases, ocfs2_iget() reads the data of inode, which has been
deleted for some reason. That will make the system panic. So We should
judge whether this inode has been deleted, and tell the caller that the
inode is a bad inode.
For example, the ocfs2 is used as the backed of nfs, and the client is
nfsv3. This issue can be reproduced by the following steps.
on the nfs server side,
..../patha/pathb
Step 1: The process A was scheduled before calling the function fh_verify.
Step 2: The process B is removing the 'pathb', and just completed the call
to function dput. Then the dentry of 'pathb' has been deleted from the
dcache, and all ancestors have been deleted also. The relationship of
dentry and inode was deleted through the function hlist_del_init. The
following is the call stack.
dentry_iput->hlist_del_init(&dentry->d_u.d_alias)
At this time, the inode is still in the dcache.
Step 3: The process A call the function ocfs2_get_dentry, which get the
inode from dcache. Then the refcount of inode is 1. The following is the
call stack.
nfsd3_proc_getacl->fh_verify->exportfs_decode_fh->fh_to_dentry(ocfs2_get_dentry)
Step 4: Dirty pages are flushed by bdi threads. So the inode of 'patha'
is evicted, and this directory was deleted. But the inode of 'pathb'
can't be evicted, because the refcount of the inode was 1.
Step 5: The process A keep running, and call the function
reconnect_path(in exportfs_decode_fh), which call function
ocfs2_get_parent of ocfs2. Get the block number of parent
directory(patha) by the name of ... Then read the data from disk by the
block number. But this inode has been deleted, so the system panic.
Process A Process B
1. in nfsd3_proc_getacl |
2. | dput
3. fh_to_dentry(ocfs2_get_dentry) |
4. bdi flush dirty cache |
5. ocfs2_iget |
[283465.542049] OCFS2: ERROR (device sdp): ocfs2_validate_inode_block:
Invalid dinode #580640: OCFS2_VALID_FL not set
[283465.545490] Kernel panic - not syncing: OCFS2: (device sdp): panic forced
after error
hugetlb uses a fault mutex hash table to prevent page faults of the
same pages concurrently. The key for shared and private mappings is
different. Shared keys off address_space and file index. Private keys
off mm and virtual address. Consider a private mappings of a populated
hugetlbfs file. A fault will map the page from the file and if needed
do a COW to map a writable page.
Hugetlbfs hole punch uses the fault mutex to prevent mappings of file
pages. It uses the address_space file index key. However, private
mappings will use a different key and could race with this code to map
the file page. This causes problems (BUG) for the page cache remove
code as it expects the page to be unmapped. A sample stack is:
There seems to be another potential COW issue/race with this approach
of different private and shared keys as noted in commit 8382d914ebf7
("mm, hugetlb: improve page-fault scalability").
Since every hugetlb mapping (even anon and private) is actually a file
mapping, just use the address_space index key for all mappings. This
results in potentially more hash collisions. However, this should not
be the common case.
Link: http://lkml.kernel.org/r/20190328234704.27083-3-mike.kravetz@oracle.com Link: http://lkml.kernel.org/r/20190412165235.t4sscoujczfhuiyt@linux-r8p5 Fixes: b5cec28d36f5 ("hugetlbfs: truncate_hugepages() takes a range of pages") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reviewed-by: Davidlohr Bueso <dbueso@suse.de> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dtor returned by get_compound_page_dtor in __put_compound_page may be
the function of free_huge_page which will lock the hugetlb_lock, so don't
put_page in lock of hugetlb_lock.
Link: http://lkml.kernel.org/r/b8ade452-2d6b-0372-32c2-703644032b47@huawei.com Fixes: 9980d744a0 ("mm, hugetlb: get rid of surplus page accounting tricks") Signed-off-by: Kai Shen <shenkai8@huawei.com> Signed-off-by: Feilong Lin <linfeilong@huawei.com> Reported-by: Wang Wang <wangwang2@huawei.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with c6f3c5ee40c1 ("mm/huge_memory.c: fix modifying of page
protection by insert_pfn_pmd()") vmf_insert_pfn_pmd() internally calls
pmdp_set_access_flags(). That helper enforces a pmd aligned @address
argument via VM_BUG_ON() assertion.
Update the implementation to take a 'struct vm_fault' argument directly
and apply the address alignment fixup internally to fix crash signatures
like:
The semantics of what mincore() considers to be resident is not
completely clear, but Linux has always (since 2.3.52, which is when
mincore() was initially done) treated it as "page is available in page
cache".
That's potentially a problem, as that [in]directly exposes
meta-information about pagecache / memory mapping state even about
memory not strictly belonging to the process executing the syscall,
opening possibilities for sidechannel attacks.
Change the semantics of mincore() so that it only reveals pagecache
information for non-anonymous mappings that belog to files that the
calling process could (if it tried to) successfully open for writing;
otherwise we'd be including shared non-exclusive mappings, which
- is the sidechannel
- is not the usecase for mincore(), as that's primarily used for data,
not (shared) text
[jkosina@suse.cz: v2] Link: http://lkml.kernel.org/r/20190312141708.6652-2-vbabka@suse.cz
[mhocko@suse.com: restructure can_do_mincore() conditions] Link: http://lkml.kernel.org/r/nycvar.YFH.7.76.1903062342020.19912@cbobk.fhfr.pm Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Josh Snyder <joshs@netflix.com> Acked-by: Michal Hocko <mhocko@suse.com> Originally-by: Linus Torvalds <torvalds@linux-foundation.org> Originally-by: Dominique Martinet <asmadeus@codewreck.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Dave Chinner <david@fromorbit.com> Cc: Kevin Easton <kevin@guarana.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Cyril Hrubis <chrubis@suse.cz> Cc: Tejun Heo <tj@kernel.org> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Daniel Gruss <daniel@gruss.cc> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
in order to support cryptocell tee fips error that may occurs while
cryptocell ree is suspended, an cc_tee_handle_fips_error call added
to the cc_pm_resume function.
Adds function that checks if cryptocell tee fips error occurred
and in such case triggers system error through kernel panic.
Change fips function to use this new routine.
During power management suspend the driver need to prepare the device
for the power down operation and as a last indication write to the
HOST_POWER_DOWN_EN register which signals to the hardware that
The ccree is ready for power down.
We were computing the size of the import buffer based on the digest size
but the 318 and 224 byte variants use 512 and 256 bytes internal state
sizes respectfully, thus causing the import buffer to overrun.
We were handling chained scattergather lists with specialized code
needlessly as the regular sg APIs handle them just fine. The code
handling this also had an (unused) code path with a use-before-init
error, flagged by Coverity.
Remove all special handling of chained sg and leave their handling
to the regular sg APIs.
Prefetch-with-intent-to-write is currently part of the XADD mapping in
the AArch64 JIT and follows the kernel's implementation of atomic_add.
This may interfere with other threads executing the LDXR/STXR loop,
leading to potential starvation and fairness issues. Drop the optional
prefetch instruction.
Fixes: 85f68fe89832 ("bpf, arm64: implement jiting of BPF_XADD") Reported-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In resume from S3, HDAC HDMI codec driver dapm event callback may be
operated before HDMI codec driver turns on the display audio power
domain because of the contest between display driver and hdmi codec driver.
This patch adds the device_link between soc card device (consumer) and
hdmi codec device (supplier) to make sure the sequence is always correct.
Signed-off-by: Libin Yang <libin.yang@intel.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current algorithm allows 3 types of transfers, 16bit, 32bit and
burst. According to Realtek, 16bit transfers have a special restriction
in that it is restricted to the memory region of
0x18020000 ~ 0x18021000. This region is the memory location of the I2C
registers. The current algorithm does not uphold this restriction and
therefore fails to complete writes.
Since this has been broken for some time it likely no one is using it.
Better to simply disable the 16 bit writes. This will allow users to
properly load firmware over SPI without data corruption.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org> Reviewed-by: Ben Zhang <benzh@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The max98090 driver defines 3 DAPM muxes; one for the right line output
(LINMOD Mux), one for the left headphone mixer source (MIXHPLSEL Mux)
and one for the right headphone mixer source (MIXHPRSEL Mux). The same
bit is used for the mux as well as the DAPM enable, and although the mux
can be correctly configured, after playback has completed, the mux will
be reset during the disable phase. This is preventing the state of these
muxes from being saved and restored correctly on system reboot. Fix this
by marking these muxes as SND_SOC_NOPM.
Note this has been verified this on the Tegra124 Nyan Big which features
the MAX98090 codec.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the System76 Gazelle (gaze14), there is a headset microphone input
attached to 0x1a that does not have a jack detect. In order to get it
working, the pin configuration needs to be set correctly, and the
ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC fixup needs to be applied. This is
identical to the patch already applied for the System76 Darter Pro
(darp5).
[ NOTE: This change is supposed to reduce the possible click noises at
(runtime) PM resume. The functionality should be same (i.e. the
verbs are executed correctly) no matter which order is, so this
should be safe to apply for all codecs -- tiwai ]
On the machines with AMD GPU or Nvidia GPU, we often meet this issue:
after s3, there are 4 HDMI/DP audio devices in the gnome-sound-setting
even there is no any monitors plugged.
When this problem happens, we check the /proc/asound/cardX/eld#N.M, we
will find the monitor_present=1, eld_valid=0.
The root cause is BIOS or GPU driver makes the PRESENCE valid even no
monitor plugged, and of course the driver will not get the valid
eld_data subsequently.
In this situation, we should not report the jack_plugged event, to do
so, let us change the function hdmi_present_sense_via_verbs(). In this
function, it reads the pin_sense via snd_hda_pin_sense(), after
calling this function, the jack_dirty is 0, and before exiting
via_verbs(), we change the shadow pin_sense according to both
monitor_present and eld_valid, then in the snd_hda_jack_report_sync(),
since the jack_dirty is still 0, it will report jack event according
to this modified shadow pin_sense.
After this change, the driver will not report Jack_is_plugged event
through hdmi_present_sense_via_verbs() if monitor_present is 1 and
eld_valid is 0.
The driver will check the monitor presence when resuming from suspend,
starting poll or interrupt triggers. In these 3 situations, the
jack_dirty will be set to 1 first, then the hda_jack.c reads the
pin_sense from register, after reading the register, the jack_dirty
will be set to 0. But hdmi_repoll_work() is enabled in these 3
situations, It will read the pin_sense a couple of times subsequently,
since the jack_dirty is 0 now, It does not read the register anymore,
instead it uses the shadow pin_sense which is read at the first time.
It is meaningless to check the shadow pin_sense a couple of times,
we need to read the register to check the real plugging state, so
we set the jack_dirty to 1 in the hdmi_repoll_work().
In parse_audio_selector_unit(), the string array 'namelist' is allocated
through kmalloc_array(), and each string pointer in this array, i.e.,
'namelist[]', is allocated through kmalloc() in the following for loop.
Then, a control instance 'kctl' is created by invoking snd_ctl_new1(). If
an error occurs during the creation process, the string array 'namelist',
including all string pointers in the array 'namelist[]', should be freed,
before the error code ENOMEM is returned. However, the current code does
not free 'namelist[]', resulting in memory leaks.
To fix the above issue, free all string pointers 'namelist[]' in a loop.
The line6 toneport driver has code for some delayed initialization,
and this hits the kernel Oops because mutex and other sleepable
functions are used in the timer callback. Fix the abuse by a delayed
work instead so that everything works gracefully.
The tag set is allocated in mmc_init_queue but never freed. This results
in a memory leak. This change makes sure we free the tag set when the
queue is also freed.
If the user-provided IV needs to be aligned to the algorithm's
alignmask, then skcipher_walk_virt() copies the IV into a new aligned
buffer walk.iv. But skcipher_walk_virt() can fail afterwards, and then
if the caller unconditionally accesses walk.iv, it's a use-after-free.
xts-aes-neonbs doesn't set an alignmask, so currently it isn't affected
by this despite unconditionally accessing walk.iv. However this is more
subtle than desired, and unconditionally accessing walk.iv has caused a
real problem in other algorithms. Thus, update xts-aes-neonbs to start
checking the return value of skcipher_walk_virt().
Fixes: 1abee99eafab ("crypto: arm64/aes - reimplement bit-sliced ARM/NEON implementation for arm64") Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user-provided IV needs to be aligned to the algorithm's
alignmask, then skcipher_walk_virt() copies the IV into a new aligned
buffer walk.iv. But skcipher_walk_virt() can fail afterwards, and then
if the caller unconditionally accesses walk.iv, it's a use-after-free.
arm32 xts-aes-neonbs doesn't set an alignmask, so currently it isn't
affected by this despite unconditionally accessing walk.iv. However
this is more subtle than desired, and it was actually broken prior to
the alignmask being removed by commit cc477bf64573 ("crypto: arm/aes -
replace bit-sliced OpenSSL NEON code"). Thus, update xts-aes-neonbs to
start checking the return value of skcipher_walk_virt().
Fixes: e4e7f10bfc40 ("ARM: add support for bit sliced AES using NEON instructions") Cc: <stable@vger.kernel.org> # v3.13+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kernel Crypto API request output the next IV data to
IV buffer for CBC implementation. So the last block data of
ciphertext should be copid into assigned IV buffer.
Reported-by: Eric Biggers <ebiggers@google.com> Fixes: 433cd2c617bf ("crypto: rockchip - add crypto driver for rk3288") Cc: <stable@vger.kernel.org> # v4.5+ Signed-off-by: Zhang Zhijie <zhangzj@rock-chips.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCM instances can be created by either the "gcm" template, which only
allows choosing the block cipher, e.g. "gcm(aes)"; or by "gcm_base",
which allows choosing the ctr and ghash implementations, e.g.
"gcm_base(ctr(aes-generic),ghash-generic)".
However, a "gcm_base" instance prevents a "gcm" instance from being
registered using the same implementations. Nor will the instance be
found by lookups of "gcm". This can be used as a denial of service.
Moreover, "gcm_base" instances are never tested by the crypto
self-tests, even if there are compatible "gcm" tests.
The root cause of these problems is that instances of the two templates
use different cra_names. Therefore, fix these problems by making
"gcm_base" instances set the same cra_name as "gcm" instances, e.g.
"gcm(aes)" instead of "gcm_base(ctr(aes-generic),ghash-generic)".
This requires extracting the block cipher name from the name of the ctr
algorithm. It also requires starting to verify that the algorithms are
really ctr and ghash, not something else entirely. But it would be
bizarre if anyone were actually using non-gcm-compatible algorithms with
gcm_base, so this shouldn't break anyone in practice.
The arm64 gcm-aes-ce algorithm is failing the extra crypto self-tests
following my patches to test the !may_use_simd() code paths, which
previously were untested. The problem is that in the !may_use_simd()
case, an odd number of AES blocks can be processed within each step of
the skcipher_walk. However, the skcipher_walk is being done with a
"stride" of 2 blocks and is advanced by an even number of blocks after
each step. This causes the encryption to produce the wrong ciphertext
and authentication tag, and causes the decryption to incorrectly fail.
Fix it by only processing an even number of blocks per step.
Fixes: c2b24c36e0a3 ("crypto: arm64/aes-gcm-ce - fix scatterwalk API violation") Fixes: 71e52c278c54 ("crypto: arm64/aes-ce-gcm - operate on two input blocks at a time") Cc: <stable@vger.kernel.org> # v4.19+ Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ->digest() method of crct10dif-pclmul reads the current CRC value
from the shash_desc context. But this value is uninitialized, causing
crypto_shash_digest() to compute the wrong result. Fix it.
Probably this wasn't noticed before because lib/crc-t10dif.c only uses
crypto_shash_update(), not crypto_shash_digest(). Likewise,
crypto_shash_digest() is not yet tested by the crypto self-tests because
those only test the ahash API which only uses shash init/update/final.
Fixes: 0b95a7f85718 ("crypto: crct10dif - Glue code to cast accelerated CRCT10DIF assembly as a crypto transform") Cc: <stable@vger.kernel.org> # v3.11+ Cc: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ->digest() method of crct10dif-generic reads the current CRC value
from the shash_desc context. But this value is uninitialized, causing
crypto_shash_digest() to compute the wrong result. Fix it.
Probably this wasn't noticed before because lib/crc-t10dif.c only uses
crypto_shash_update(), not crypto_shash_digest(). Likewise,
crypto_shash_digest() is not yet tested by the crypto self-tests because
those only test the ahash API which only uses shash init/update/final.
This bug was detected by my patches that improve testmgr to fuzz
algorithms against their generic implementation.
Fixes: 2d31e518a428 ("crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework") Cc: <stable@vger.kernel.org> # v3.11+ Cc: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skcipher_walk_done() assumes it's a bug if, after the "slow" path is
executed where the next chunk of data is processed via a bounce buffer,
the algorithm says it didn't process all bytes. Thus it WARNs on this.
However, this can happen legitimately when the message needs to be
evenly divisible into "blocks" but isn't, and the algorithm has a
'walksize' greater than the block size. For example, ecb-aes-neonbs
sets 'walksize' to 128 bytes and only supports messages evenly divisible
into 16-byte blocks. If, say, 17 message bytes remain but they straddle
scatterlist elements, the skcipher_walk code will take the "slow" path
and pass the algorithm all 17 bytes in the bounce buffer. But the
algorithm will only be able to process 16 bytes, triggering the WARN.
Fix this by just removing the WARN_ON(). Returning -EINVAL, as the code
already does, is the right behavior.
This bug was detected by my patches that improve testmgr to fuzz
algorithms against their generic implementation.
Fixes: b286d8b1a690 ("crypto: skcipher - Add skcipher walk interface") Cc: <stable@vger.kernel.org> # v4.10+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original assembly imported from OpenSSL has two copy-paste
errors in handling CTR mode. When dealing with a 2 or 3 block tail,
the code branches to the CBC decryption exit path, rather than to
the CTR exit path.
This leads to corruption of the IV, which leads to subsequent blocks
being corrupted.
This can be detected with libkcapi test suite, which is available at
https://github.com/smuellerDD/libkcapi
Reported-by: Ondrej Mosnáček <omosnacek@gmail.com> Fixes: 5c380d623ed3 ("crypto: vmx - Add support for VMS instructions by ASM") Cc: stable@vger.kernel.org Signed-off-by: Daniel Axtens <dja@axtens.net> Tested-by: Michael Ellerman <mpe@ellerman.id.au> Tested-by: Ondrej Mosnacek <omosnacek@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we free the psp_master if the PLATFORM_INIT fails during the
SEV FW probe. If psp_master is freed then driver does not invoke the PSP
FW. As per SEV FW spec, there are several commands (PLATFORM_RESET,
PLATFORM_STATUS, GET_ID etc) which can be executed in the UNINIT state
We should not free the psp_master when PLATFORM_INIT fails.
Fixes: 200664d5237f ("crypto: ccp: Add SEV support") Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Gary Hook <gary.hook@amd.com> Cc: stable@vger.kernel.org # 4.19.y Signed-off-by: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the rfc7539 template is instantiated with specific implementations,
e.g. "rfc7539(chacha20-generic,poly1305-generic)" rather than
"rfc7539(chacha20,poly1305)", then the implementation names end up
included in the instance's cra_name. This is incorrect because it then
prevents all users from allocating "rfc7539(chacha20,poly1305)", if the
highest priority implementations of chacha20 and poly1305 were selected.
Also, the self-tests aren't run on an instance allocated in this way.
Fix it by setting the instance's cra_name from the underlying
algorithms' actual cra_names, rather than from the requested names.
This matches what other templates do.
Fixes: 71ebc4d1b27d ("crypto: chacha20poly1305 - Add a ChaCha20-Poly1305 AEAD construction, RFC7539") Cc: <stable@vger.kernel.org> # v4.2+ Cc: Martin Willi <martin@strongswan.org> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Martin Willi <martin@strongswan.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user-provided IV needs to be aligned to the algorithm's
alignmask, then skcipher_walk_virt() copies the IV into a new aligned
buffer walk.iv. But skcipher_walk_virt() can fail afterwards, and then
if the caller unconditionally accesses walk.iv, it's a use-after-free.
salsa20-generic doesn't set an alignmask, so currently it isn't affected
by this despite unconditionally accessing walk.iv. However this is more
subtle than desired, and it was actually broken prior to the alignmask
being removed by commit b62b3db76f73 ("crypto: salsa20-generic - cleanup
and convert to skcipher API").
Since salsa20-generic does not update the IV and does not need any IV
alignment, update it to use req->iv instead of walk.iv.
Currently, crypto4xx CFB and OFB AES ciphers are
failing testmgr's test vectors.
|cfb-aes-ppc4xx encryption overran dst buffer on test vector 3, cfg="in-place"
|ofb-aes-ppc4xx encryption overran dst buffer on test vector 1, cfg="in-place"
This is because of a very subtile "bug" in the hardware that
gets indirectly mentioned in 18.1.3.5 Encryption/Decryption
of the hardware spec:
the OFB and CFB modes for AES are listed there as operation
modes for >>> "Block ciphers" <<<. Which kind of makes sense,
but we would like them to be considered as stream ciphers just
like the CTR mode.
To workaround this issue and stop the hardware from causing
"overran dst buffer" on crypttexts that are not a multiple
of 16 (AES_BLOCK_SIZE), we force the driver to use the scatter
buffers as the go-between.
As a bonus this patch also kills redundant pd_uinfo->num_gd
and pd_uinfo->num_sd setters since the value has already been
set before.
Cc: stable@vger.kernel.org Fixes: f2a13e7cba9e ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8efd972ef96a ("crypto: testmgr - support checking skcipher output IV")
caused the crypto4xx driver to produce the following error:
| ctr-aes-ppc4xx encryption test failed (wrong output IV)
| on test vector 0, cfg="in-place"
This patch fixes this by reworking the crypto4xx_setkey_aes()
function to:
- not save the iv for ECB (as per 18.2.38 CRYP0_SA_CMD_0:
"This bit mut be cleared for DES ECB mode or AES ECB mode,
when no IV is used.")
- instruct the hardware to save the generated IV for all
other modes of operations that have IV and then supply
it back to the callee in pretty much the same way as we
do it for cbc-aes already.
- make it clear that the DIR_(IN|OUT)BOUND is the important
bit that tells the hardware to encrypt or decrypt the data.
(this is cosmetic - but it hopefully prevents me from
getting confused again).
- don't load any bogus hash when we don't use any hash
operation to begin with.
Cc: stable@vger.kernel.org Fixes: f2a13e7cba9e ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2c7577a75837 ("sched/x86_64: Don't save flags on context switch")
Specifically because SMAP uses FLAGS.AC which invalidates the claim
that the kernel has clean flags.
In particular; while preemption from interrupt return is fine (the
IRET frame on the exception stack contains FLAGS) it breaks any code
that does synchonous scheduling, including preempt_enable().
This has become a significant issue ever since commit:
5b24a7a2aa20 ("Add 'unsafe' user access functions for batched accesses")
provided for means of having 'normal' C code between STAC / CLAC,
exposing the FLAGS.AC state. So far this hasn't led to trouble,
however fix it before it comes apart.
Reported-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@kernel.org Fixes: 5b24a7a2aa20 ("Add 'unsafe' user access functions for batched accesses") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the CPU comes out of suspend, the firmware may have modified the OS
Double Lock Register. Save it in an unused slot of cpu_suspend_ctx, and
restore it on resume.
Currently, compat tasks running on arm64 can allocate memory up to
TASK_SIZE_32 (UL(0x100000000)).
This means that mmap() allocations, if we treat them as returning an
array, are not compliant with the sections 6.5.8 of the C standard
(C99) which states that: "If the expression P points to an element of
an array object and the expression Q points to the last element of the
same array object, the pointer expression Q+1 compares greater than P".
When executing clock_gettime(), either in the vDSO or via a system call,
we need to ensure that the read of the counter register occurs within
the seqlock reader critical section. This ensures that updates to the
clocksource parameters (e.g. the multiplier) are consistent with the
counter value and therefore avoids the situation where time appears to
go backwards across multiple reads.
Extend the vDSO logic so that the seqlock critical section covers the
read of the counter register as well as accesses to the data page. Since
reads of the counter system registers are not ordered by memory barrier
instructions, introduce dependency ordering from the counter read to a
subsequent memory access so that the seqlock memory barriers apply to
the counter access in both the vDSO and the system call paths.
The file offset argument to the arm64 sys_mmap() implementation is
scaled from bytes to pages by shifting right by PAGE_SHIFT.
Unfortunately, the offset is passed in as a signed 'off_t' type and
therefore large offsets (i.e. with the top bit set) are incorrectly
sign-extended by the shift. This has been observed to cause false mmap()
failures when mapping GPU doorbells on an arm64 server part.
Change the type of the file offset argument to sys_mmap() from 'off_t'
to 'unsigned long' so that the shifting scales the value as expected.
The ACEPC T8 and T11 Cherry Trail Z8350 mini PCs use an AXP288 and as PCs,
rather then portables, they does not have a battery. Still for some
reason the AXP288 not only thinks there is a battery, it actually
thinks it is discharging while the PC is running, slowly going to
0% full, causing userspace to shutdown the system due to the battery
being critically low after a while.
This commit adds the ACEPC T8 and T11 to the axp288 fuel-gauge driver
blacklist, so that we stop reporting bogus battery readings on this device.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1690852 Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there is no check on platform_get_irq() return value
in case it fails, hence never actually reporting any errors and
causing unexpected behavior when using such value as argument
for function regmap_irq_get_virq().
Fix this by adding a proper check, a message reporting any errors
and returning *pirq*
Addresses-Coverity-ID: 1443940 ("Improper use of negative value") Fixes: 843735b788a4 ("power: axp288_charger: axp288 charger driver") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to of_get_next_child returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with warnings like:
arch/arm/mach-exynos/firmware.c:201:2-8: ERROR: missing of_node_put;
acquired a node pointer with refcount incremented on line 193,
but without a corresponding object release within this function.
Cc: stable@vger.kernel.org Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Direct commands (DCMDs) are an optional feature of eMMC 5.1's command
queue engine (CQE). The Arasan eMMC 5.1 controller uses the CQHCI,
which exposes a control register bit to enable the feature.
The current implementation sets this bit unconditionally.
This patch allows to suppress the feature activation,
by specifying the property disable-cqe-dcmd.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: 84362d79f436 ("mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name of CODEC input widget to which microphone is connected through
the "Headphone" jack is "IN12" not "IN1". This fixes microphone support
on Odroid XU3.
The driver shows this message only for the first spurious interrupt
by using WARN_ONCE(). Changing this to WARN() shows, that this is
happening quite frequently (up to once a second).
Since the eMMC 5.1 specification, where CQE and CQHCI are specified,
does not mention that spurious TCN interrupts for DCMDs can be simply
ignored, we must assume that using this feature is not working reliably.
The current implementation uses DCMD for REQ_OP_FLUSH only, and
I could not see any performance/power impact when disabling
this optional feature for RK3399.
Therefore this patch disables DCMDs for RK3399.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Fixes: 84362d79f436 ("mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1") Cc: stable@vger.kernel.org
[the corresponding code changes are queued for 5.2 so doing that as well] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a function falls through to the next function due to a compiler
bug, objtool prints some obscure warnings. For example:
drivers/regulator/core.o: warning: objtool: regulator_count_voltages()+0x95: return with modified stack frame
drivers/regulator/core.o: warning: objtool: regulator_count_voltages()+0x0: stack state mismatch: cfa1=7+32 cfa2=7+8
Instead it should be printing:
drivers/regulator/core.o: warning: objtool: regulator_supply_is_couple() falls through to next function regulator_count_voltages()
This used to work, but was broken by the following commit:
13810435b9a7 ("objtool: Support GCC 8's cold subfunctions")
The padding nops at the end of a function aren't actually part of the
function, as defined by the symbol table. So the 'func' variable in
validate_branch() is getting cleared to NULL when a padding nop is
encountered, breaking the fallthrough detection.
If the current instruction doesn't have a function associated with it,
just consider it to be part of the previously detected function by not
overwriting the previous value of 'func'.
On x86_64, all returns to usermode go through
prepare_exit_to_usermode(), with the sole exception of do_nmi().
This even includes machine checks -- this was added several years
ago to support MCE recovery. Update the documentation.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@suse.de> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jon Masters <jcm@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: 04dcbdb80578 ("x86/speculation/mds: Clear CPU buffers on exit to user") Link: http://lkml.kernel.org/r/999fa9e126ba6a48e9d214d2f18dbde5c62ac55c.1557865329.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The double fault ESPFIX path doesn't return to user mode at all --
it returns back to the kernel by simulating a #GP fault.
prepare_exit_to_usermode() will run on the way out of
general_protection before running user code.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@suse.de> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jon Masters <jcm@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: 04dcbdb80578 ("x86/speculation/mds: Clear CPU buffers on exit to user") Link: http://lkml.kernel.org/r/ac97612445c0a44ee10374f6ea79c222fe22a5c4.1557865329.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During my rwsem testing, it was found that after a down_read(), the
reader count may occasionally become 0 or even negative. Consequently,
a writer may steal the lock at that time and execute with the reader
in parallel thus breaking the mutual exclusion guarantee of the write
lock. In other words, both readers and writer can become rwsem owners
simultaneously.
The current reader wakeup code does it in one pass to clear waiter->task
and put them into wake_q before fully incrementing the reader count.
Once waiter->task is cleared, the corresponding reader may see it,
finish the critical section and do unlock to decrement the count before
the count is incremented. This is not a problem if there is only one
reader to wake up as the count has been pre-incremented by 1. It is
a problem if there are more than one readers to be woken up and writer
can steal the lock.
The wakeup was actually done in 2 passes before the following v4.9 commit:
70800c3c0cc5 ("locking/rwsem: Scan the wait_list for readers only once")
To fix this problem, the wakeup is now done in two passes
again. In the first pass, we collect the readers and count them.
The reader count is then fully incremented. In the second pass, the
waiter->task is then cleared and they are put into wake_q to be woken
up later.
Signed-off-by: Waiman Long <longman@redhat.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Will Deacon <will.deacon@arm.com> Cc: huang ying <huang.ying.caritas@gmail.com> Fixes: 70800c3c0cc5 ("locking/rwsem: Scan the wait_list for readers only once") Link: http://lkml.kernel.org/r/20190428212557.13482-2-longman@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When we hot-remove a device, usually the host sends us a PCI_EJECT message,
and a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
When we execute the quick hot-add/hot-remove test, the host may not send
us the PCI_EJECT message if the guest has not fully finished the
initialization by sending the PCI_RESOURCES_ASSIGNED* message to the
host, so it's potentially unsafe to only depend on the
pci_destroy_slot() in hv_eject_device_work() because the code path
create_root_hv_pci_bus()
-> hv_pci_assign_slots()
is not called in this case. Note: in this case, the host still sends the
guest a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
In the quick hot-add/hot-remove test, we can have such a race before
the code path
adds the new device into the hbus->children list, we may have already
received the PCI_EJECT message, and since the tasklet handler
hv_pci_onchannelcallback()
may fail to find the "hpdev" by calling
get_pcichild_wslot(hbus, dev_message->wslot.slot)
hv_pci_eject_device() is not called; Later, by continuing execution
create_root_hv_pci_bus()
-> hv_pci_assign_slots()
creates the slot and the PCI_BUS_RELATIONS message with
bus_rel->device_count == 0 removes the device from hbus->children, and
we end up being unable to remove the slot in
hv_pci_remove()
-> hv_pci_remove_slots()
Remove the slot in pci_devices_present_work() when the device
is removed to address this race.
pci_devices_present_work() and hv_eject_device_work() run in the
singled-threaded hbus->wq, so there is not a double-remove issue for the
slot.
We cannot offload hv_pci_eject_device() from hv_pci_onchannelcallback()
to the workqueue, because we need the hv_pci_onchannelcallback()
synchronously call hv_pci_eject_device() to poll the channel
ringbuffer to work around the "hangs in hv_compose_msi_msg()" issue
fixed in commit de0aa7b2f97d ("PCI: hv: Fix 2 hang issues in
hv_compose_msi_msg()")
Fixes: a15f2c08c708 ("PCI: hv: support reporting serial number as slot information") Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: rewritten commit log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we unload the pci-hyperv host controller driver, the host does not
send us a PCI_EJECT message.
In this case we also need to make sure the sysfs PCI slot directory is
removed, otherwise a command on a slot file eg:
"cat /sys/bus/pci/slots/2/address"
will trigger a
"BUG: unable to handle kernel paging request"
and, if we unload/reload the driver several times we would end up with
stale slot entries in PCI slot directories in /sys/bus/pci/slots/
root@localhost:~# ls -rtl /sys/bus/pci/slots/
total 0
drwxr-xr-x 2 root root 0 Feb 7 10:49 2
drwxr-xr-x 2 root root 0 Feb 7 10:49 2-1
drwxr-xr-x 2 root root 0 Feb 7 10:51 2-2
Add the missing code to remove the PCI slot and fix the current
behaviour.
Fixes: a15f2c08c708 ("PCI: hv: support reporting serial number as slot information") Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: reformatted the log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device is created in new_pcichild_device(), hpdev->refs is set
to 2 (i.e. the initial value of 1 plus the get_pcichild()).
When we hot remove the device from the host, in a Linux VM we first call
hv_pci_eject_device(), which increases hpdev->refs by get_pcichild() and
then schedules a work of hv_eject_device_work(), so hpdev->refs becomes
3 (let's ignore the paired get/put_pcichild() in other places). But in
hv_eject_device_work(), currently we only call put_pcichild() twice,
meaning the 'hpdev' struct can't be freed in put_pcichild().
Add one put_pcichild() to fix the memory leak.
The device can also be removed when we run "rmmod pci-hyperv". On this
path (hv_pci_remove() -> hv_pci_bus_exit() -> hv_pci_devices_present()),
hpdev->refs is 2, and we do correctly call put_pcichild() twice in
pci_devices_present_work().
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs") Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: commit log rework] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set RI in the default kernel's MSR so that the architected way of
detecting unrecoverable machine check interrupts has a chance to work.
This is inline with the MSR setup of the rest of booke powerpc
architectures configured here.
Without restoring the IAMR after idle, execution prevention on POWER9
with Radix MMU is overwritten and the kernel can freely execute
userspace without faulting.
This is necessary when returning from any stop state that modifies
user state, as well as hypervisor state.
To test how this fails without this patch, load the lkdtm driver and
do the following:
When the memset code was added to pgd_alloc(), it failed to consider
that kmem_cache_alloc() can return NULL. It's uncommon, but not
impossible under heavy memory contention. Example oops:
The "param.count" value is a u64 thatcomes from the user. The code
later in the function assumes that param.count is at least one and if
it's not then it leads to an Oops when we dereference the ZERO_SIZE_PTR.
Also the addition can have an integer overflow which would lead us to
allocate a smaller "pages" array than required. I can't immediately
tell what the possible run times implications are, but it's safest to
prevent the overflow.
Link: http://lkml.kernel.org/r/20181218082129.GE32567@kadam Fixes: 6db7199407ca ("drivers/virt: introduce Freescale hypervisor management driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Timur Tabi <timur@freescale.com> Cc: Mihai Caraman <mihai.caraman@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 517d7c79bdb398 ("tipc: fix hanging poll() for stream sockets")
introduced a regression for clients using non-blocking sockets.
After the commit, we send EPOLLOUT event to the client even in
TIPC_CONNECTING state. This causes the subsequent send() to fail
with ENOTCONN, as the socket is still not in TIPC_ESTABLISHED state.
In this commit, we:
- improve the fix for hanging poll() by replacing sk_data_ready()
with sk_state_change() to wake up all clients.
- revert the faulty updates introduced by commit 517d7c79bdb398
("tipc: fix hanging poll() for stream sockets").
Fixes: 517d7c79bdb398 ("tipc: fix hanging poll() for stream sockets") Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com> Acked-by: Jon Maloy <jon.maloy@ericsson.se> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch to make bas_gigaset use usb_fill_int_urb() - instead of
filling that urb "by hand" - missed the subtle ordering of the previous
code.
See, before the switch urb->dev was set to a member somewhere deep in a
complicated structure and then supplied to usb_rcvisocpipe() and
usb_sndisocpipe(). After that switch urb->dev wasn't set to anything
specific before being supplied to those two macros. This triggers a
nasty oops:
No-one noticed because this Oops is apparently only triggered by setting
up an ISDN data connection on a live ISDN line on a gigaset base (ie,
the PBX that the gigaset driver support). Very few people do that
running present day kernels.
Anyhow, a little code reorganization makes this problem go away, while
avoiding the subtle ordering that was used in the past. So let's do
that.
Fixes: 78c696c19578 ("isdn: gigaset: use usb_fill_int_urb()") Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a queue(tfile) is detached through __tun_detach(), we move the
last enabled tfile to the position where detached one sit but don't
NULL out last position. We expect to synchronize the datapath through
tun->numqueues. Unfortunately, this won't work since we're lacking
sufficient mechanism to order or synchronize the access to
tun->numqueues.
To fix this, NULL out the last position during detaching and check
RCU protected tfile against NULL instead of checking tun->numqueues in
datapath.
Cc: YueHaibing <yuehaibing@huawei.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: weiyongjun (A) <weiyongjun1@huawei.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Fixes: c8d68e6be1c3b ("tuntap: multiqueue support") Signed-off-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need check if tun->numqueues is zero (e.g for the persist device)
before trying to use it for modular arithmetic.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Fixes: 96f84061620c6("tun: add eBPF based queue selection method") Signed-off-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VRF netdev mtu isn't typically set and have an mtu of 65536. When the
link of a tunnel is set, the tunnel mtu is changed from 1480 to the link
mtu minus tunnel header. In the case of VRF netdev is the link, then the
tunnel mtu becomes 65516. So, fix it by not setting the tunnel mtu in
this case.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With NET_ADMIN enabled in container, a normal user could be mapped to
root and is able to change the real device's rx filter via ioctl on
vlan, which would affect the other ptp process on host. Fix it by
disabling SIOCSHWTSTAMP in container.
Fixes: a6111d3c93d0 ("vlan: Pass SIOC[SG]HWTSTAMP ioctls to real device") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
calling connect(AF_UNSPEC) on an already connected TCP socket is an
established way to disconnect() such socket. After commit 68741a8adab9
("selinux: Fix ltp test connect-syscall failure") it no longer works
and, in the above scenario connect() fails with EAFNOSUPPORT.
Fix the above falling back to the generic/old code when the address family
is not AF_INET{4,6}, but leave the SCTP code path untouched, as it has
specific constraints.
Fixes: 68741a8adab9 ("selinux: Fix ltp test connect-syscall failure") Reported-by: Tom Deseyn <tdeseyn@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When modprobe af_packet, register_pernet_subsys
fails and does a cleanup, ops->list is set to LIST_POISON1,
but the module init is considered to success, then while rmmod it,
BUG() is triggered in __list_del_entry_valid which is called from
unregister_pernet_subsys. This patch fix error handing path in
packet_init to avoid possilbe issue if some error occur.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When changing the number of buffers in the RX ring while the interface
is running, the following Oops is encountered due to the new number
of buffers being taken into account immediately while their allocation
is done when opening the device only.
The old MIPS implementation of dma_cache_sync() didn't use the dev argument,
but commit c9eb6172c328 ("dma-mapping: turn dma_cache_sync into a
dma_map_ops method") changed that, so we now need to set dev.parent.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current order in open:
-> Enable interrupts (macb_init_hw)
-> Enable NAPI
-> Start PHY
Sequence of RX handling:
-> RX interrupt occurs
-> Interrupt is cleared and interrupt bits disabled in handler
-> NAPI is scheduled
-> In NAPI, RX budget is processed and RX interrupts are re-enabled
With the above, on QEMU or fixed link setups (where PHY state doesn't
matter), there's a chance macb RX interrupt occurs before NAPI is
enabled. This will result in NAPI being scheduled before it is enabled.
Fix this macb open by changing the order.
Fixes: ae1f2a56d273 ("net: macb: Added support for many RX queues") Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanup allocated resourses if there are errors,
otherwise it will trgger memleak.
Fixes: c9eb3e0f8701 ("net: dsa: Add support for learning FDB through notification") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
inet_iif should be used for the raw socket lookup. inet_iif considers
rt_iif which handles the case of local traffic.
As it stands, ping to a local address with the '-I <dev>' option fails
ever since ping was changed to use SO_BINDTODEVICE instead of
cmsg + IP_PKTINFO.
IPv6 works fine.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 153380ec4b9 ("fib_rules: Added NLM_F_EXCL support to
fib_nl_newrule") we now able to check if a rule already exists. But this
only works with iproute2. For other tools like libnl, NetworkManager,
it still could add duplicate rules with only NLM_F_CREATE flag, like
[localhost ~ ]# ip rule
0: from all lookup local
32766: from all lookup main
32767: from all lookup default
100000: from 192.168.7.5 lookup 5
100000: from 192.168.7.5 lookup 5
As it doesn't make sense to create two duplicate rules, let's just return
0 if the rule exists.
Fixes: 153380ec4b9 ("fib_rules: Added NLM_F_EXCL support to fib_nl_newrule") Reported-by: Thomas Haller <thaller@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix issue with the entry indexing in the sg frame cleanup code being
off-by-1. This problem showed up when doing some basic iperf tests and
manifested in traffic coming to a halt.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Acked-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently error return from kobject_init_and_add() is not followed by a
call to kobject_put(). This means there is a memory leak. We currently
set p to NULL so that kfree() may be called on it as a noop, the code is
arguably clearer if we move the kfree() up closer to where it is
called (instead of after goto jump).
Remove a goto label 'err1' and jump to call to kobject_put() in error
return from kobject_init_and_add() fixing the memory leak. Re-name goto
label 'put_back' to 'err1' now that we don't use err1, following current
nomenclature (err1, err2 ...). Move call to kfree out of the error
code at bottom of function up to closer to where memory was allocated.
Add comment to clarify call to kfree().
Signed-off-by: Tobin C. Harding <tobin@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's currently a problem with toggling arp_validate on and off with an
active-backup bond. At the moment, you can start up a bond, like so:
modprobe bonding mode=1 arp_interval=100 arp_validate=0 arp_ip_targets=192.168.1.1
ip link set bond0 down
echo "ens4f0" > /sys/class/net/bond0/bonding/slaves
echo "ens4f1" > /sys/class/net/bond0/bonding/slaves
ip link set bond0 up
ip addr add 192.168.1.2/24 dev bond0
Pings to 192.168.1.1 work just fine. Now turn on arp_validate:
Pings to 192.168.1.1 continue to work just fine. Now when you go to turn
arp_validate off again, the link falls flat on it's face:
echo 0 > /sys/class/net/bond0/bonding/arp_validate
dmesg
...
[133191.911987] bond0: Setting arp_validate to none (0)
[133194.257793] bond0: bond_should_notify_peers: slave ens4f0
[133194.258031] bond0: link status definitely down for interface ens4f0, disabling it
[133194.259000] bond0: making interface ens4f1 the new active one
[133197.330130] bond0: link status definitely down for interface ens4f1, disabling it
[133197.331191] bond0: now running without any active interface!
The problem lies in bond_options.c, where passing in arp_validate=0
results in bond->recv_probe getting set to NULL. This flies directly in
the face of commit 3fe68df97c7f, which says we need to set recv_probe =
bond_arp_recv, even if we're not using arp_validate. Said commit fixed
this in bond_option_arp_interval_set, but missed that we can get to that
same state in bond_option_arp_validate_set as well.
One solution would be to universally set recv_probe = bond_arp_recv here
as well, but I don't think bond_option_arp_validate_set has any business
touching recv_probe at all, and that should be left to the arp_interval
code, so we can just make things much tidier here.
Fixes: 3fe68df97c7f ("bonding: always set recv_probe to bond_arp_rcv in arp monitor") CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: "David S. Miller" <davem@davemloft.net> CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current powerpc security.c file is defining functions, as
cpu_show_meltdown(), cpu_show_spectre_v{1,2} and others, that are being
declared at linux/cpu.h header without including the header file that
contains these declarations.
This is being reported by sparse, which thinks that these functions are
static, due to the lack of declaration:
arch/powerpc/kernel/security.c:105:9: warning: symbol 'cpu_show_meltdown' was not declared. Should it be static?
arch/powerpc/kernel/security.c:139:9: warning: symbol 'cpu_show_spectre_v1' was not declared. Should it be static?
arch/powerpc/kernel/security.c:161:9: warning: symbol 'cpu_show_spectre_v2' was not declared. Should it be static?
arch/powerpc/kernel/security.c:209:6: warning: symbol 'stf_barrier' was not declared. Should it be static?
arch/powerpc/kernel/security.c:289:9: warning: symbol 'cpu_show_spec_store_bypass' was not declared. Should it be static?
This patch simply includes the proper header (linux/cpu.h) to match
function definition and declaration.
Signed-off-by: Breno Leitao <leitao@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Cc: Joel Stanley <joel@jms.id.au> Cc: Nathan Chancellor <natechancellor@gmail.com> Cc: Major Hayden <major@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changing state from check_state_check_result to
check_state_compute_result not only is unsafe but also doesn't
appear to serve a valid purpose. A raid6 check should only be
pushing out extra writes if doing repair and a mis-match occurs.
The stripe dev management will already try and do repair writes
for failing sectors.
This patch makes the raid6 check_state_check_result handling
work more like raid5's. If somehow too many failures for a
check, just quit the check operation for the stripe. When any
checks pass, don't try and use check_state_compute_result for
a purpose it isn't needed for and is unsafe for. Just mark the
stripe as in sync for passing its parity checks and let the
stripe dev read/write code and the bad blocks list do their
job handling I/O errors.
Repro steps from Xiao:
These are the steps to reproduce this problem:
1. redefined OPT_MEDIUM_ERR_ADDR to 12000 in scsi_debug.c
2. insmod scsi_debug.ko dev_size_mb=11000 max_luns=1 num_tgts=1
3. mdadm --create /dev/md127 --level=6 --raid-devices=5 /dev/sde1 /dev/sde2 /dev/sde3 /dev/sde5 /dev/sde6
sde is the disk created by scsi_debug
4. echo "2" >/sys/module/scsi_debug/parameters/opts
5. raid-check
Add missing break statement in order to prevent the code from falling
through to case 0x1025, and erroneously setting rtlhal->oem_id to
RT_CID_819X_ACER when rtlefuse->eeprom_svid is equal to 0x10EC and
none of the cases in switch (rtlefuse->eeprom_smid) match.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: 238ad2ddf34b ("rtlwifi: rtl8723ae: Clean up the hardware info routine") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was reported on OpenWrt bug tracking system[1], that several users
are affected by the endless reboot of their routers if they configure
5GHz interface with channel 44 or 48.
The reboot loop is caused by the following excessive number of WARN_ON
messages:
WARNING: CPU: 0 PID: 0 at backports-4.19.23-1/net/mac80211/rx.c:4516
ieee80211_rx_napi+0x1fc/0xa54 [mac80211]
as the messages are being correctly emitted by the following guard:
case RX_ENC_LEGACY:
if (WARN_ON(status->rate_idx >= sband->n_bitrates))
as the rate_idx is in this case erroneously set to 251 (0xfb). This fix
simply converts previously used magic number to proper constant and
guards against substraction which is leading to the currently observed
underflow.
Fixes: 854783444bab ("mwl8k: properly set receive status rate index on 5 GHz receive") Cc: <stable@vger.kernel.org> Tested-by: Eubert Bao <bunnier@gmail.com> Reported-by: Eubert Bao <bunnier@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
