Bjorn Andersson [Tue, 8 Feb 2022 04:16:05 +0000 (22:16 -0600)]
arm64: dts: qcom: c630: Add backlight controller
The Lenovo Yoga C630 uses the PWM controller in the TI SN65DSI86 bridge
chip to provide a signal for the backlight control and has TLMM GPIO 11
attached to some regulator that drives the backlight.
Unfortunately the regulator attached to this gpio is also powering the
camera, so turning off backlight result in the detachment of the camera
as well.
Add the new herobrine-r1. Note that this is pretty much a re-design
compared to herobrine-r0 so we don't attempt any dtsi to share stuff
between them.
This patch attempts to define things at 3 levels:
1. The Qcard level. Herobrine includes a Qcard PCB and the Qcard PCB
is supposed to be the same (modulo stuffing options) across
multiple boards, so trying to define what's there hopefully makes
sense. NOTE that newer "CRD" boards from Qualcomm also use
Qcard. When support for CRD3 is added hopefully it can use the
Qcard include (and perhaps we should even evaluate it using
herobrine.dtsi?)
2. The herobrine "baseboard" level. Right now most stuff is here with
the exception of things that we _know_ will be different per
board. We know that not all boards will have the same set of eMMC,
nvme, and SD. We also know that the exact pin names are likely to
be different.
3. The actual "board" level, AKA herobrine-rev1.
NOTES:
- This boots to command prompt. We're still waiting on the PWM driver.
- This assumes LTE for now. Once it's clear how WiFi-only SKUs will
work we expect some small changes.
arm64: dts: qcom: sc7280: Add a blank line in the dp node
It's weird that there's a blank line between the two port nodes but
not between the attributes and the first port node. Add an extra blank
line to make it look right.
Pulls should be in the board files, not in the SoC dtsi
file. Remove. Even though the sc7280 boards don't currently refer to
dp_hot_plug_det, let's re-add the pulls there just to keep this as a
no-op change. If boards don't need this / don't want it later then we
can remove it from them.
arm64: dts: qcom: sc7280: Add edp_out port and HPD lines
Like dp_out, we should have defined edp_out in sc7280.dtsi so we don't
need to do this in the board files.
Like dp_hot_plug_det, we should define edp_hot_plug_det in
sc7280.dtsi.
We should set the default pinctrl for edp_hot_plug_det in
sc7280.dtsi. NOTE: this is _unlike_ the dp_hot_plug_det. It is
reasonable that in some boards the dedicated DP Hot Plug Detect will
not be hooked up in favor of Type C mechanisms. This is unlike eDP
where the Hot Plug Detect line (which functions as "panel ready" in
eDP) is highly likely to be used by boards.
arm64: dts: qcom: sc7280-idp: No need for "input-enable" on sw_ctrl
Specifying "input-enable" on a MSM GPIO is a no-op for the most
part. The only thing it really does is to explicitly force the output
of a GPIO to be disabled right at the point of a pinctrl
transition. We don't need to do this and we don't typically specify
"input-enable" unless there's a good reason to. Remove it.
arm64: dts: qcom: sc7280: Clean up sdc1 / sdc2 pinctrl
This patch makes a few improvements to the way that sdc1 / sdc2
pinctrl is specified on sc7280:
1. There's no reason to "group" the sdc pins into one overarching node
and there's a downside: we have to replicate the hierarchy in the
board device tree files. Let's clean this up.
2. There's really not a lot of reason not to list the "pinctrl" for
sdc1 (eMMC) in the SoC dtsi file. These aren't GPIO pins and
everyone's going to specify the same pins.
3. Even though it's likely that boards will need to override pinctrl
for sdc2 (SD card) to add the card detect GPIO, we can be symmetric
and add it to the SoC dsti file.
4. Let's get rid of the word "on" from the normal config and add a
"sleep" suffix to the sleep config. This looks cleaner to me.
This is intended to be a no-op change but it could plausibly change
behavior depending on how the pinctrl code parses things. One thing to
note is that "SD card detect" is explicitly listed now as keeping its
pull enabled in sleep since we still want to detect card insertions
even if the controller is suspended (because no card is inserted). The
pinctrl framework likely did this anyway, but it's nice to see it
explicit.
The sdc1 / sdc2 pinctrl lines were randomly stuffed in the middle of
the qup pinctrl lines. Sort them properly. This is a no-op
change. Just code movement.
Some of the fixed regulators were missing the "-regulator" suffix. Add
it to be consistent within the file and consistent with the fixed
regulators in sc7180-trogdor.
Alex Elder [Tue, 1 Feb 2022 14:07:23 +0000 (08:07 -0600)]
arm64: dts: qcom: add IPA qcom,qmp property
At least three platforms require the "qcom,qmp" property to be
specified, so the IPA driver can request register retention across
power collapse. Update DTS files accordingly.
The OnePlus 6 and 6T feature a BQ27411 fuel gauge for reading the
battery stats. Enable it and add a simple battery to document the
battery specs of each device.
Petr Vorel [Thu, 13 Jan 2022 23:33:55 +0000 (00:33 +0100)]
arm64: dts: qcom: msm8994: Provide missing "xo_board" and "sleep_clk" to GCC
This is needed due changes in commit 0519d1d0bf33 ("clk: qcom:
gcc-msm8994: Modernize the driver"), which removed struct
clk_fixed_factor. Preparation for next commit for enabling SD/eMMC.
Inspired by 2c2f64ae36d9.
This is required for both msm8994-huawei-angler (sdhc1 will be enabled
in next commit) and msm8992-lg-bullhead (where actually fixes sdhc1
- tested on bullhead rev 1.01).
Maulik Shah [Sun, 9 Jan 2022 17:25:01 +0000 (22:55 +0530)]
arm64: dts: qcom: sm8450: Update cpuidle states parameters
This change updates/corrects below cpuidle parameters
1. entry-latency, exit-latency and residency for various idle states.
2. arm,psci-suspend-param which is same for CLUSTER_SLEEP_0/1 states.
3. Add CLUSTER_SLEEP_1 in CLUSTER_PD.
The SM6125_VDDCX constant was replaced with 0 temporarily as the header
patch defining this constant resided in a different branch, creating an
unwanted dependency of the dts branch on the drivers branch.
Now (by the time this patch will be applied) that both branches have
been merged upstream, it is safe to revert to the constant again.
Add the generic 'max-link-speed' property to describe the IPQ6018 PCIe
link generation limit. This allows the generic dwc code to configure the
link speed correctly.
dt-schema expect to have fallback compatible, which is now in-place.
Fixes warning generated by `make qcom/sdm845-oneplus-fajita.dtb`:
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: power-controller@c300000: compatible: ['qcom,sdm845-aoss-qmp'] is too short
From schema: Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.yaml
Rob Herring [Fri, 17 Dec 2021 21:11:36 +0000 (15:11 -0600)]
arm64: dts: qcom: msm8998: Fix cache nodes
The msm8998 cache nodes have some issues. First, L1 caches are described
within cpu nodes, not as separate nodes. The 'next-level-cache' property
is of course in the correct location, otherwise the cache hierarchy
walking would not work. Remove all the L1 cache nodes.
Second, 'arm,arch-cache' is not a documented compatible string. "cache"
is a sufficient compatible string for the Arm architected caches.
Felipe Balbi [Fri, 17 Dec 2021 12:45:46 +0000 (14:45 +0200)]
arm64: dts: qcom: sm8150: simplify references to pwrkey and resin
Since commit d0a6ce59ea4e ("arm64: dts: qcom: sm8150: Add support for
SONY Xperia 1 / 5 (Kumano platform)"), we can directly refer to pwrkey
and resin by their new labels, respectively pon_pwrkey and pon_resin.
Simplify microsof surface duo DTS by utilizing the new labels.
David Heidelberg [Tue, 14 Dec 2021 23:46:47 +0000 (00:46 +0100)]
arm64: dts: qcom: sdm845: rename memory@ nodes to more descriptive names
Pure effort to avoid `make dtbs_check` warnings about memory@ nodes, which
should have property device_type set to memory.
Fixes warnings as:
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: memory@f5b00000: 'device_type' is a required property
From schema: dtschema/schemas/memory.yaml
Stephan Gerhold [Tue, 14 Dec 2021 13:51:24 +0000 (14:51 +0100)]
arm64: dts: qcom: apq8016-sbc: Fix dtbs_check warnings for &sound
qcom,apq8016-sbc-sndcard is now covered by the qcom,sm8250.yaml schema
which has slightly different recommendations for the naming of
properties and nodes. The old naming is still functional but
deprecated. Update the &sound node in apq8016-sbc to fix the following
dtbs_check warnings:
apq8016-sbc.dt.yaml: sound@7702000: 'model' is a required property
From schema: sound/qcom,sm8250.yaml
apq8016-sbc.dt.yaml: sound@7702000: 'external-dai-link@0', ...
do not match any of the regexes: '.*-dai-link$', ...
From schema: sound/qcom,sm8250.yaml
David Heidelberg [Mon, 13 Dec 2021 19:51:04 +0000 (20:51 +0100)]
arm64: dts: qcom: sdm845: fix microphone bias properties and values
replace millivolt with correct microvolt and adjust value to
the minimal value allowed by documentation.
Found with `make qcom/sdm845-oneplus-fajita.dtb`.
Fixes:
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias1-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias2-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias3-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias4-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias1-millivolt', 'qcom,micbias2-millivolt', 'qcom,micbias3-millivolt', 'qcom,micbias4-millivolt' do not match any of the regexes: '^.*@[0-9a-f]+$', 'pinctrl-[0-9]+'
Douglas Anderson [Tue, 25 Jan 2022 22:44:21 +0000 (14:44 -0800)]
arm64: dts: qcom: sc7280: Factor gpio.h include to sc7280.dtsi
Though sc7280 itself doesn't need any of the defines in gpio.h, it's
highly likely that the actual boards will use them. Let's add the
include to the sc7280.dtsi file so that boards don't need to do it.
Douglas Anderson [Tue, 25 Jan 2022 22:44:20 +0000 (14:44 -0800)]
arm64: dts: qcom: sc7280: Factor out Chrome common fragment
This factors out a device tree fragment from some sc7280 device
trees. It represents the device tree bits that should be included for
"Chrome" based sc7280 boards. On these boards the bootloader (Coreboot
+ Depthcharge) configures things slightly different than the
bootloader that Qualcomm provides. The modem firmware on these boards
also works differently than on other Qulacomm products and thus the
reserved memory map needs to be adjusted.
NOTES:
- This is _not_ quite a no-op change. The "herobrine" and "idp"
fragments here were different and it looks like someone simply
forgot to update the herobrine version. This updates a few numbers
to match IDP. This will also cause the `pmk8350_pon` to be disabled
on idp/crd, which I belive is a correct change.
- At the moment this assumes LTE skus. Once it's clearer how WiFi SKUs
will work (how much of the memory map they can reclaim) we may add
an extra fragment that will rejigger one way or the other.
Douglas Anderson [Tue, 25 Jan 2022 22:44:19 +0000 (14:44 -0800)]
arm64: dts: qcom: sc7280: Move herobrine-r0 to its own dts
The upcoming herobrine-r1 board is really not very similar to
herobrine-r0. Let's get rid of the "herobrine.dtsi" file and stick all
the content in the -r0 dts file directly. We'll also rename the dts so
it's obvious that it's just for -r0.
While renaming, let's actually name the file so it's obvious that
"herobrine" is both the name of the board and the name of the
"baseboard". In other words "herobrine" is an actual board but also
often used as the name of a whole class of similar boards that forked
from a design. While "herobrine-herobrine" is a bit of mouthful it
makes it more obvious which things are part of an actual board rather
than the baseboard.
NOTE: herobrine-rev0's days are likely doomed and this device tree is
likely to be deleted in the future.
Stephen Boyd [Thu, 16 Dec 2021 04:45:29 +0000 (20:45 -0800)]
arm64: dts: qcom: sc7180: Add board regulators for MIPI camera trogdor boards
Some trogdor boards have on-board regulators for the MIPI camera
components. Add nodes describing these regulators so boards with these
supplies can consume them.
Cc: Douglas Anderson <dianders@chromium.org> Cc: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20211216044529.733652-1-swboyd@chromium.org
arm64: dts: qcom: sc7280: Move USB2 controller nodes from common dtsi to SKU1
Move USB2 controller and phy nodes from common dtsi file as it is
required only for SKU1 board and change the mode to host mode as
it will be used in host mode for SKU1.
Linus Torvalds [Sun, 23 Jan 2022 06:14:21 +0000 (08:14 +0200)]
Merge tag 'perf-tools-for-v5.17-2022-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Fix printing 'phys_addr' in 'perf script'.
- Fix failure to add events with 'perf probe' in ppc64 due to not
removing leading dot (ppc64 ABIv1).
- Fix cpu_map__item() python binding building.
- Support event alias in form foo-bar-baz, add pmu-events and
parse-event tests for it.
- No need to setup affinities when starting a workload or attaching to
a pid.
- Use path__join() to compose a path instead of ad-hoc snprintf()
equivalent.
- Override attr->sample_period for non-libpfm4 events.
- Use libperf cpumap APIs instead of accessing the internal state
directly.
- Sync x86 arch prctl headers and files changed by the new
set_mempolicy_home_node syscall with the kernel sources.
- Remove duplicate include in cpumap.h.
- Remove redundant err variable.
* tag 'perf-tools-for-v5.17-2022-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf tools: Remove redundant err variable
perf test: Add parse-events test for aliases with hyphens
perf test: Add pmu-events test for aliases with hyphens
perf parse-events: Support event alias in form foo-bar-baz
perf evsel: Override attr->sample_period for non-libpfm4 events
perf cpumap: Remove duplicate include in cpumap.h
perf cpumap: Migrate to libperf cpumap api
perf python: Fix cpu_map__item() building
perf script: Fix printing 'phys_addr' failure issue
tools headers UAPI: Sync files changed by new set_mempolicy_home_node syscall
tools headers UAPI: Sync x86 arch prctl headers with the kernel sources
perf machine: Use path__join() to compose a path instead of snprintf(dir, '/', filename)
perf evlist: No need to setup affinities when disabling events for pid targets
perf evlist: No need to setup affinities when enabling events for pid targets
perf stat: No need to setup affinities when starting a workload
perf affinity: Allow passing a NULL arg to affinity__cleanup()
perf probe: Fix ppc64 'perf probe add events failed' case
Linus Torvalds [Sun, 23 Jan 2022 06:07:02 +0000 (08:07 +0200)]
Merge tag 'trace-v5.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"Fix s390 breakage from sorting mcount tables.
The latest merge of the tracing tree sorts the mcount table at build
time. But s390 appears to do things differently (like always) and
replaces the sorted table back to the original unsorted one. As the
ftrace algorithm depends on it being sorted, bad things happen when it
is not, and s390 experienced those bad things.
Add a new config to tell the boot if the mcount table is sorted or
not, and allow s390 to opt out of it"
* tag 'trace-v5.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix assuming build time sort works for s390
ftrace: Fix assuming build time sort works for s390
To speed up the boot process, as mcount_loc needs to be sorted for ftrace
to work properly, sorting it at build time is more efficient than boot up
and can save milliseconds of time. Unfortunately, this change broke s390
as it will modify the mcount_loc location after the sorting takes place
and will put back the unsorted locations. Since the sorting is skipped at
boot up if it is believed that it was sorted at run time, ftrace can crash
as its algorithms are dependent on the list being sorted.
Add a new config BUILDTIME_MCOUNT_SORT that is set when
BUILDTIME_TABLE_SORT but not if S390 is set. Use this config to determine
if sorting should take place at boot up.
Link: https://lore.kernel.org/all/yt9dee51ctfn.fsf@linux.ibm.com/ Fixes: 72b3942a173c ("scripts: ftrace - move the sort-processing in ftrace_init") Reported-by: Sven Schnelle <svens@linux.ibm.com> Tested-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Linus Torvalds [Sun, 23 Jan 2022 04:32:29 +0000 (06:32 +0200)]
Merge tag 'kbuild-fixes-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Bring include/uapi/linux/nfc.h into the UAPI compile-test coverage
- Revert the workaround of CONFIG_CC_IMPLICIT_FALLTHROUGH
- Fix build errors in certs/Makefile
* tag 'kbuild-fixes-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
certs: Fix build error when CONFIG_MODULE_SIG_KEY is empty
certs: Fix build error when CONFIG_MODULE_SIG_KEY is PKCS#11 URI
Revert "Makefile: Do not quote value for CONFIG_CC_IMPLICIT_FALLTHROUGH"
usr/include/Makefile: add linux/nfc.h to the compile-test coverage
Linus Torvalds [Sun, 23 Jan 2022 04:20:44 +0000 (06:20 +0200)]
Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
John Garry [Mon, 17 Jan 2022 15:10:14 +0000 (23:10 +0800)]
perf test: Add pmu-events test for aliases with hyphens
Add a test for aliases with hyphens in the name to ensure that the
pmu-events tables are as expects. There should be no reason why these sort
of aliases would be treated differently, but no harm in checking.
Signed-off-by: John Garry <john.garry@huawei.com> Acked-by: Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kajol Jain <kjain@linux.ibm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Qi Liu <liuqi115@huawei.com> Cc: Shaokun Zhang <zhangshaokun@hisilicon.com> Cc: linuxarm@huawei.com Link: https://lore.kernel.org/r/1642432215-234089-3-git-send-email-john.garry@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
John Garry [Mon, 17 Jan 2022 15:10:13 +0000 (23:10 +0800)]
perf parse-events: Support event alias in form foo-bar-baz
Event aliasing for events whose name in the form foo-bar-baz is not
supported, while foo-bar, foo_bar_baz, and other combinations are, i.e.
two hyphens are not supported.
The HiSilicon D06 platform has events in such form:
German Gomez [Tue, 18 Jan 2022 14:40:54 +0000 (14:40 +0000)]
perf evsel: Override attr->sample_period for non-libpfm4 events
A previous patch preventing "attr->sample_period" values from being
overridden in pfm events changed a related behaviour in arm-spe.
Before said patch:
perf record -c 10000 -e arm_spe_0// -- sleep 1
Would yield an SPE event with period=10000. After the patch, the period
in "-c 10000" was being ignored because the arm-spe code initializes
sample_period to a non-zero value.
This patch restores the previous behaviour for non-libpfm4 events.
Fixes: ae5dcc8abe31 (“perf record: Prevent override of attr->sample_period for libpfm4 events”) Reported-by: Chase Conklin <chase.conklin@arm.com> Signed-off-by: German Gomez <german.gomez@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: KP Singh <kpsingh@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Cc: Yonghong Song <yhs@fb.com> Cc: bpf@vger.kernel.org Cc: netdev@vger.kernel.org Link: http://lore.kernel.org/lkml/20220118144054.2541-1-german.gomez@arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ian Rogers [Sat, 22 Jan 2022 04:58:10 +0000 (20:58 -0800)]
perf cpumap: Migrate to libperf cpumap api
Switch from directly accessing the perf_cpu_map to using the appropriate
libperf API when possible. Using the API simplifies the job of
refactoring use of perf_cpu_map.
Signed-off-by: Ian Rogers <irogers@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: André Almeida <andrealmeid@collabora.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Darren Hart <dvhart@infradead.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Dmitriy Vyukov <dvyukov@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: German Gomez <german.gomez@arm.com> Cc: James Clark <james.clark@arm.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: John Garry <john.garry@huawei.com> Cc: Kajol Jain <kjain@linux.ibm.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Madhavan Srinivasan <maddy@linux.ibm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Miaoqian Lin <linmq006@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Riccardo Mancini <rickyman7@gmail.com> Cc: Shunsuke Nakamura <nakamura.shun@fujitsu.com> Cc: Song Liu <song@kernel.org> Cc: Stephane Eranian <eranian@google.com> Cc: Stephen Brennan <stephen.s.brennan@oracle.com> Cc: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Richter <tmricht@linux.ibm.com> Cc: Yury Norov <yury.norov@gmail.com> Link: http://lore.kernel.org/lkml/20220122045811.3402706-3-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ian Rogers [Sat, 22 Jan 2022 04:58:09 +0000 (20:58 -0800)]
perf python: Fix cpu_map__item() building
Value should be built as an integer.
Switch some uses of perf_cpu_map to use the library API.
Fixes: 6d18804b963b78dc ("perf cpumap: Give CPUs their own type") Signed-off-by: Ian Rogers <irogers@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: André Almeida <andrealmeid@collabora.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Darren Hart <dvhart@infradead.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Dmitriy Vyukov <dvyukov@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: German Gomez <german.gomez@arm.com> Cc: Ian Rogers <irogers@google.com> Cc: James Clark <james.clark@arm.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: John Garry <john.garry@huawei.com> Cc: Kajol Jain <kjain@linux.ibm.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Madhavan Srinivasan <maddy@linux.ibm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Miaoqian Lin <linmq006@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Riccardo Mancini <rickyman7@gmail.com> Cc: Shunsuke Nakamura <nakamura.shun@fujitsu.com> Cc: Song Liu <song@kernel.org> Cc: Stephane Eranian <eranian@google.com> Cc: Stephen Brennan <stephen.s.brennan@oracle.com> Cc: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Richter <tmricht@linux.ibm.com> Cc: Yury Norov <yury.norov@gmail.com> Link: http://lore.kernel.org/lkml/20220122045811.3402706-2-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Perf script was failed to print the phys_addr for SPE profiling.
One 'dummy' event is added by SPE profiling but it doesn't have PHYS_ADDR
attribute set, perf script then exits with error.
Now referring to 'addr', use evsel__do_check_stype() to check the type.
Before:
# perf record -e arm_spe_0/branch_filter=0,ts_enable=1,pa_enable=1,load_filter=1,jitter=0,\
store_filter=0,min_latency=0,event_filter=2/ -p 4064384 -- sleep 3
# perf script -F pid,tid,addr,phys_addr
Samples for 'dummy:u' event do not have PHYS_ADDR attribute set. Cannot print 'phys_addr' field.
Reviewed-by: German Gomez <german.gomez@arm.com> Signed-off-by: Yao Jin <jinyao5@huawei.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20220121065954.2121900-1-liwei391@huawei.com Signed-off-by: Wei Li <liwei391@huawei.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Masahiro Yamada [Thu, 20 Jan 2022 19:22:05 +0000 (04:22 +0900)]
certs: Fix build error when CONFIG_MODULE_SIG_KEY is empty
Since b8c96a6b466c ("certs: simplify $(srctree)/ handling and remove
config_filename macro"), when CONFIG_MODULE_SIG_KEY is empty,
signing_key.x509 fails to build:
Dmitry V. Levin [Mon, 3 Jan 2022 01:24:02 +0000 (04:24 +0300)]
usr/include/Makefile: add linux/nfc.h to the compile-test coverage
As linux/nfc.h userspace compilation was finally fixed by commits 79b69a83705e ("nfc: uapi: use kernel size_t to fix user-space builds")
and 7175f02c4e5f ("uapi: fix linux/nfc.h userspace compilation errors"),
there is no need to keep the compile-test exception for it in
usr/include/Makefile.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Linus Torvalds [Sat, 22 Jan 2022 09:28:23 +0000 (11:28 +0200)]
Merge branch 'akpm' (patches from Andrew)
Merge yet more updates from Andrew Morton:
"This is the post-linux-next queue. Material which was based on or
dependent upon material which was in -next.
69 patches.
Subsystems affected by this patch series: mm (migration and zsmalloc),
sysctl, proc, and lib"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (69 commits)
mm: hide the FRONTSWAP Kconfig symbol
frontswap: remove support for multiple ops
mm: mark swap_lock and swap_active_head static
frontswap: simplify frontswap_register_ops
frontswap: remove frontswap_test
mm: simplify try_to_unuse
frontswap: remove the frontswap exports
frontswap: simplify frontswap_init
frontswap: remove frontswap_curr_pages
frontswap: remove frontswap_shrink
frontswap: remove frontswap_tmem_exclusive_gets
frontswap: remove frontswap_writethrough
mm: remove cleancache
lib/stackdepot: always do filter_irq_stacks() in stack_depot_save()
lib/stackdepot: allow optional init and stack_table allocation by kvmalloc()
proc: remove PDE_DATA() completely
fs: proc: store PDE()->data into inode->i_private
zsmalloc: replace get_cpu_var with local_lock
zsmalloc: replace per zpage lock with pool->migrate_lock
locking/rwlocks: introduce write_lock_nested
...
Linus Torvalds [Sat, 22 Jan 2022 09:12:26 +0000 (11:12 +0200)]
Merge tag '5.17-rc-part2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
- multichannel fixes, addressing additional reconnect and DFS scenarios
- reenabling fscache support (indexing rewrite, metadata caching e.g.)
- send additional version information during NTLMSSP negotiate to
improve debugging
- fix for a mount race
- DFS fixes
- fix for a memory leak for stable
* tag '5.17-rc-part2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module number
smb3: send NTLMSSP version information
cifs: Support fscache indexing rewrite
cifs: cifs_ses_mark_for_reconnect should also update reconnect bits
cifs: update tcpStatus during negotiate and sess setup
cifs: make status checks in version independent callers
cifs: remove repeated state change in dfs tree connect
cifs: fix the cifs_reconnect path for DFS
cifs: remove unused variable ses_selected
cifs: protect all accesses to chan_* with chan_lock
cifs: fix the connection state transitions with multichannel
cifs: check reconnects for channels of active tcons too
smb3: add new defines from protocol specification
cifs: serialize all mount attempts
cifs: quirk for STATUS_OBJECT_NAME_INVALID returned for non-ASCII dfs refs
cifs: alloc_path_with_tree_prefix: do not append sep. if the path is empty
cifs: clean up an inconsistent indenting
cifs: free ntlmsspblob allocated in negotiate
Linus Torvalds [Sat, 22 Jan 2022 09:04:27 +0000 (11:04 +0200)]
Merge tag 'xfs-5.17-merge-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"One of the patches removes some dead code from xfs_ioctl32.h and the
other fixes broken workqueue flushing in the inode garbage collector.
- Minor cleanup of ioctl32 cruft
- Clean up open coded inodegc workqueue function calls"
* tag 'xfs-5.17-merge-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: flush inodegc workqueue tasks before cancel
xfs: remove unused xfs_ioctl32.h declarations
Linus Torvalds [Sat, 22 Jan 2022 08:59:32 +0000 (10:59 +0200)]
Merge tag 'fscache-fixes-20220121' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull more fscache updates from David Howells:
"A set of fixes and minor updates for the fscache rewrite:
- Fix mishandling of volume collisions (the wait condition is
inverted and so it was only waiting if the volume collision was
already resolved).
- Fix miscalculation of whether there's space available in
cachefiles.
- Make sure a default cache name is set on a cache if the user hasn't
set one by the time they bind the cache.
- Adjust the way the backing inode is presented in tracepoints, add a
tracepoint for mkdir and trace directory lookup.
- Add a tracepoint for failure to set the active file mark.
- Add an explanation of the checks made on the backing filesystem.
- Check that the backing filesystem supports tmpfile.
- Document how the page-release cancellation of the read-skip
optimisation works.
And I've included a change for netfslib:
- Make ops->init_rreq() optional"
* tag 'fscache-fixes-20220121' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
netfs: Make ops->init_rreq() optional
fscache: Add a comment explaining how page-release optimisation works
cachefiles: Check that the backing filesystem supports tmpfiles
cachefiles: Explain checks in a comment
cachefiles: Trace active-mark failure
cachefiles: Make some tracepoint adjustments
cachefiles: set default tag name if it's unspecified
cachefiles: Calculate the blockshift in terms of bytes, not pages
fscache: Fix the volume collision wait condition
Linus Torvalds [Sat, 22 Jan 2022 08:43:07 +0000 (10:43 +0200)]
Merge tag 'folio-5.17a' of git://git.infradead.org/users/willy/pagecache
Pull more folio updates from Matthew Wilcox:
"Three small folio patches.
One bug fix, one patch pulled forward from the patches destined for
5.18 and then a patch to make use of that functionality"
* tag 'folio-5.17a' of git://git.infradead.org/users/willy/pagecache:
filemap: Use folio_put_refs() in filemap_free_folio()
mm: Add folio_put_refs()
pagevec: Initialise folio_batch->percpu_pvec_drained
projects / thirdparty / kernel / linux.git / log
