f09d160992d1 ("x86/entry/64: Get rid of the ALLOC_PT_GPREGS_ON_STACK and SAVE_AND_CLEAR_REGS macros")
... one of my suggested improvements triggered a frame pointer warning:
arch/x86/entry/entry_64.o: warning: objtool: paranoid_entry()+0x11: call without frame pointer save/setup
The warning is correct for the build-time code, but it's actually not
relevant at runtime because of paravirt patching. The paravirt swapgs
call gets replaced with either a SWAPGS instruction or NOPs at runtime.
Go back to the previous behavior by removing the ELF function annotation
for paranoid_entry() and adding an unwind hint, which effectively
silences the warning.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kbuild-all@01.org Cc: tipbuild@zytor.com Fixes: f09d160992d1 ("x86/entry/64: Get rid of the ALLOC_PT_GPREGS_ON_STACK and SAVE_AND_CLEAR_REGS macros") Link: http://lkml.kernel.org/r/20180212174503.5acbymg5z6p32snu@treble Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, error_entry() and paranoid_entry() saved the GP registers
onto stack space previously allocated by its callers. Combine these two
steps in the callers, and use the generic PUSH_AND_CLEAR_REGS macro
for that.
This adds a significant amount ot text size. However, Ingo Molnar points
out that:
"these numbers also _very_ significantly over-represent the
extra footprint. The assumptions that resulted in
us compressing the IRQ entry code have changed very
significantly with the new x86 IRQ allocation code we
introduced in the last year:
- IRQ vectors are usually populated in tightly clustered
groups.
With our new vector allocator code the typical per CPU
allocation percentage on x86 systems is ~3 device vectors
and ~10 fixed vectors out of ~220 vectors - i.e. a very
low ~6% utilization (!). [...]
The days where we allocated a lot of vectors on every
CPU and the compression of the IRQ entry code text
mattered are over.
- Another issue is that only a small minority of vectors
is frequent enough to actually matter to cache utilization
in practice: 3-4 key IPIs and 1-2 device IRQs at most - and
those vectors tend to be tightly clustered as well into about
two groups, and are probably already on 2-3 cache lines in
practice.
For the common case of 'cache cold' IRQs it's the depth of
the call chain and the fragmentation of the resulting I$
that should be the main performance limit - not the overall
size of it.
- The CPU side cost of IRQ delivery is still very expensive
even in the best, most cached case, as in 'over a thousand
cycles'. So much stuff is done that maybe contemporary x86
IRQ entry microcode already prefetches the IDT entry and its
expected call target address."[*]
The "testb $3, CS(%rsp)" instruction in the idtentry macro does not need
modification. Previously, %rsp was manually decreased by 15*8; with
this patch, %rsp is decreased by 15 pushq instructions.
[jpoimboe@redhat.com: unwind hint improvements]
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dan.j.williams@intel.com Link: http://lkml.kernel.org/r/20180211104949.12992-7-linux@dominikbrodowski.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
entry_SYSCALL_64_after_hwframe() and nmi() can be converted to use
PUSH_AND_CLEAN_REGS instead of opencoded variants thereof. Due to
the interleaving, the additional XOR-based clearing of R8 and R9
in entry_SYSCALL_64_after_hwframe() should not have any noticeable
negative implications.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dan.j.williams@intel.com Link: http://lkml.kernel.org/r/20180211104949.12992-6-linux@dominikbrodowski.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those instances where ALLOC_PT_GPREGS_ON_STACK is called just before
SAVE_AND_CLEAR_REGS can trivially be replaced by PUSH_AND_CLEAN_REGS.
This macro uses PUSH instead of MOV and should therefore be faster, at
least on newer CPUs.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dan.j.williams@intel.com Link: http://lkml.kernel.org/r/20180211104949.12992-5-linux@dominikbrodowski.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Same as is done for syscalls, interleave XOR with PUSH instructions
for exceptions/interrupts, in order to minimize the cost of the
additional instructions required for register clearing.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dan.j.williams@intel.com Link: http://lkml.kernel.org/r/20180211104949.12992-4-linux@dominikbrodowski.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear the 'extra' registers on entering the 64-bit kernel for exceptions
and interrupts. The common registers are not cleared since they are
likely clobbered well before they can be exploited in a speculative
execution attack.
Originally-From: Andi Kleen <ak@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Cc: <stable@vger.kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/151787989146.7847.15749181712358213254.stgit@dwillia2-desk3.amr.corp.intel.com
[ Made small improvements to the changelog and the code comments. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f85942207516 (x86: PM: Make APM idle driver initialize polling
state) made apm_init() call cpuidle_poll_state_init(), but that only
is defined for CONFIG_CPU_IDLE set, so make the empty stub of it
available for CONFIG_CPU_IDLE unset too to fix the resulting build
issue.
Fixes: f85942207516 (x86: PM: Make APM idle driver initialize polling state) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit baa8809f6097 (PM / runtime: Optimize the use of device links)
added an invocation of pm_runtime_drop_link() to __device_link_del().
However there are two variants of that function, one for CONFIG_SRCU and
another for !CONFIG_SRCU, and the commit only modified the former.
Fixes: baa8809f6097 (PM / runtime: Optimize the use of device links) Cc: v4.10+ <stable@vger.kernel.org> # v4.10+ Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We either clear the CPU_BASED_USE_MSR_BITMAPS and end up intercepting all
MSR accesses or create a valid L02 MSR bitmap and use that. This decision
has to be made every time we evaluate whether we are going to generate the
L02 MSR bitmap.
Before commit:
d28b387fb74d ("KVM/VMX: Allow direct access to MSR_IA32_SPEC_CTRL")
... this was probably OK since the decision was always identical.
This is no longer the case now since the MSR bitmap might actually
change once we decide to not intercept SPEC_CTRL and PRED_CMD.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: arjan.van.de.ven@intel.com Cc: dave.hansen@intel.com Cc: jmattson@google.com Cc: kvm@vger.kernel.org Cc: sironi@amazon.de Link: http://lkml.kernel.org/r/1518305967-31356-6-git-send-email-dwmw@amazon.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two variables should check whether SPEC_CTRL and PRED_CMD are
supposed to be passed through to L2 guests or not. While
msr_write_intercepted_l01 would return 'true' if it is not passed through.
So just invert the result of msr_write_intercepted_l01 to implement the
correct semantics.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Reviewed-by: Jim Mattson <jmattson@google.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: arjan.van.de.ven@intel.com Cc: dave.hansen@intel.com Cc: kvm@vger.kernel.org Cc: sironi@amazon.de Fixes: 086e7d4118cc ("KVM: VMX: Allow direct access to MSR_IA32_SPEC_CTRL") Link: http://lkml.kernel.org/r/1518305967-31356-5-git-send-email-dwmw@amazon.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With retpoline, tight loops of "call this function for every XXX" are
very much pessimised by taking a prediction miss *every* time. This one
is by far the biggest contributor to the guest launch time with retpoline.
By marking the iterator slot_handle_…() functions always_inline, we can
ensure that the indirect function call can be optimised away into a
direct call and it actually generates slightly smaller code because
some of the other conditionals can get optimised away too.
Performance is now pretty close to what we see with nospectre_v2 on
the command line.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Tested-by: Filippo Sironi <sironi@amazon.de> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Reviewed-by: Filippo Sironi <sironi@amazon.de> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: arjan.van.de.ven@intel.com Cc: dave.hansen@intel.com Cc: jmattson@google.com Cc: karahmed@amazon.de Cc: kvm@vger.kernel.org Cc: rkrcmar@redhat.com Link: http://lkml.kernel.org/r/1518305967-31356-4-git-send-email-dwmw@amazon.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cannot call C functions like that, without marking all the
call-clobbered registers as, well, clobbered. We might have got away
with it for now because the __ibp_barrier() function was *fairly*
unlikely to actually use any other registers. But no. Just no.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: arjan.van.de.ven@intel.com Cc: dave.hansen@intel.com Cc: jmattson@google.com Cc: karahmed@amazon.de Cc: kvm@vger.kernel.org Cc: pbonzini@redhat.com Cc: rkrcmar@redhat.com Cc: sironi@amazon.de Link: http://lkml.kernel.org/r/1518305967-31356-3-git-send-email-dwmw@amazon.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arjan points out that the Intel document only clears the 0xc2 microcode
on *some* parts with CPUID 506E3 (INTEL_FAM6_SKYLAKE_DESKTOP stepping 3).
For the Skylake H/S platform it's OK but for Skylake E3 which has the
same CPUID it isn't (yet) cleared.
So removing it from the blacklist was premature. Put it back for now.
Also, Arjan assures me that the 0x84 microcode for Kaby Lake which was
featured in one of the early revisions of the Intel document was never
released to the public, and won't be until/unless it is also validated
as safe. So those can change to 0x80 which is what all *other* versions
of the doc have identified.
Once the retrospective testing of existing public microcodes is done, we
should be back into a mode where new microcodes are only released in
batches and we shouldn't even need to update the blacklist for those
anyway, so this tweaking of the list isn't expected to be a thing which
keeps happening.
Requested-by: Arjan van de Ven <arjan.van.de.ven@intel.com> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: arjan.van.de.ven@intel.com Cc: dave.hansen@intel.com Cc: kvm@vger.kernel.org Cc: pbonzini@redhat.com Link: http://lkml.kernel.org/r/1518449255-2182-1-git-send-email-dwmw@amazon.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel have retroactively blessed the 0xc2 microcode on Skylake mobile
and desktop parts, and the Gemini Lake 0x22 microcode is apparently fine
too. We blacklisted the latter purely because it was present with all
the other problematic ones in the 2018-01-08 release, but now it's
explicitly listed as OK.
We still list 0x84 for the various Kaby Lake / Coffee Lake parts, as
that appeared in one version of the blacklist and then reverted to
0x80 again. We can change it if 0x84 is actually announced to be safe.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: arjan.van.de.ven@intel.com Cc: jmattson@google.com Cc: karahmed@amazon.de Cc: kvm@vger.kernel.org Cc: pbonzini@redhat.com Cc: rkrcmar@redhat.com Cc: sironi@amazon.de Link: http://lkml.kernel.org/r/1518305967-31356-2-git-send-email-dwmw@amazon.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch splits the linear mapping if the hot-unplug range is
smaller than the mapping size. The code detects if the mapping needs
to be split into a smaller size and if so, uses the stop machine
infrastructure to clear the existing mapping and then remap the
remaining range using a smaller page size.
The code will skip any region of the mapping that overlaps with kernel
text and warn about it once. We don't want to remove a mapping where
the kernel text and the LMB we intend to remove overlap in the same
TLB mapping as it may affect the currently executing code.
I've tested these changes under a kvm guest with 2 vcpus, from a split
mapping point of view, some of the caveats mentioned above applied to
the testing I did.
Fixes: 4b5d62ca17a1 ("powerpc/mm: add radix__remove_section_mapping()") Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Tweak change log to match updated behaviour] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lockdep detects a possible deadlock in sun4i_ss_prng_generate() and
throws an "inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage" warning.
Disabling softirqs to fix this.
Fixes: b8ae5c7387ad ("crypto: sun4i-ss - support the Security System PRNG") Signed-off-by: Artem Savkov <artem.savkov@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At entry userspace may have populated registers with values that could
otherwise be useful in a speculative execution attack. Clear them to
minimize the kernel's attack surface.
Originally-From: Andi Kleen <ak@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Cc: <stable@vger.kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/151787989697.7847.4083702787288600552.stgit@dwillia2-desk3.amr.corp.intel.com
[ Made small improvements to the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At entry userspace may have (maliciously) populated the extra registers
outside the syscall calling convention with arbitrary values that could
be useful in a speculative execution (Spectre style) attack.
Clear these registers to minimize the kernel's attack surface.
Note, this only clears the extra registers and not the unused
registers for syscalls less than 6 arguments, since those registers are
likely to be clobbered well before their values could be put to use
under speculation.
Note, Linus found that the XOR instructions can be executed with
minimized cost if interleaved with the PUSH instructions, and Ingo's
analysis found that R10 and R11 should be included in the register
clearing beyond the typical 'extra' syscall calling convention
registers.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Reported-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Cc: <stable@vger.kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/151787988577.7847.16733592218894189003.stgit@dwillia2-desk3.amr.corp.intel.com
[ Made small improvements to the changelog and the code comments. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the APM driver overlooked by commit 1b39e3f813b4 (cpuidle: Make
drivers initialize polling state) to initialize the polling state like
the other cpuidle drivers modified by that commit to prevent cpuidle
from crashing.
Fixes: 1b39e3f813b4 (cpuidle: Make drivers initialize polling state) Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: 4.14+ <stable@vger.kernel.org> # 4.14+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running as Xen pv guest %gs is initialized some time after
C code is started. Depending on stack protector usage this might be
too late, resulting in page faults.
So setup %gs and MSR_GS_BASE in assembly code already.
Currently kexec() will crash when switching into a 5-level paging
enabled kernel.
I missed that we need to change relocate_kernel() to set CR4.LA57
flag if the kernel has 5-level paging enabled.
I avoided using #ifdef CONFIG_X86_5LEVEL here and inferred if we need to
enable 5-level paging from previous CR4 value. This way the code is
ready for boot-time switching between paging modes.
With this patch applied, in addition to kexec 4-to-4 which always worked,
we can kexec 4-to-5 and 5-to-5 - while 5-to-4 will need more work.
Reported-by: Baoquan He <bhe@redhat.com> Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Tested-by: Baoquan He <bhe@redhat.com> Cc: <stable@vger.kernel.org> # v4.14+ Cc: Borislav Petkov <bp@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Fixes: 77ef56e4f0fb ("x86: Enable 5-level paging support via CONFIG_X86_5LEVEL=y") Link: http://lkml.kernel.org/r/20180129110845.26633-1-kirill.shutemov@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CFL was missing from intel_early_ids[]. The PCI ID needs to be there to
allow the memory region to be stolen, otherwise we could have RAM being
arbitrarily overwritten if for example we keep using the UEFI framebuffer,
depending on how BIOS has set up the e820 map.
Fixes: b056f8f3d6b9 ("drm/i915/cfl: Add Coffee Lake PCI IDs for S Skus.") Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: David Airlie <airlied@linux.ie> Cc: intel-gfx@lists.freedesktop.org Cc: dri-devel@lists.freedesktop.org Cc: Ingo Molnar <mingo@kernel.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86@kernel.org Cc: <stable@vger.kernel.org> # v4.13+ 0890540e21cf drm/i915: add GT number to intel_device_info Cc: <stable@vger.kernel.org> # v4.13+ 41693fd52373 drm/i915/kbl: Change a KBL pci id to GT2 from GT1.5 Cc: <stable@vger.kernel.org> # v4.13+ Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Acked-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171213200425.2954-1-lucas.demarchi@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Up to Coffeelake we could deduce this GT number from the device ID.
This doesn't seem to be the case anymore. This change reorders pciids
per GT and adds a gt field to intel_device_info. We set this field on
the following platforms :
The "dmas" cells for the designware DMA controller need to have only 3
properties apart from the phandle: request line, src master and
destination master. But the commit 6e8887f60f60 updated it incorrectly
while moving from platform code to DT. Fix it.
The GPIO polarity is missing in the hdmi,hpd-gpio property, this
fixes the following DT warnings:
arch/arm/boot/dts/stih410-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih407-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih410-b2260.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
[arnd: marked Cc:stable since this warning shows up with the latest dtc
by default, and is more likely to actually cause problems than the
other patches from this series]
dtc warns about obviously incorrect GPIO numbers for the audio codec
on both lpc32xx boards:
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
It looks like the nodes are written for a different binding that combines
the GPIO number into a single number rather than a bank/number pair.
I found the right numbers on stackexchange.com, so this patch fixes
the warning and has a reasonable chance of getting things to actually
work.
SMSM is not symmetrical, the incoming bits from WCNSS are available at
index 6, but the outgoing host id for WCNSS is 3. Further more, upstream
references the base of APCS (in contrast to downstream), so the register
offset of 8 must be included.
Fixes: 1fb47e0a9ba4 ("arm64: dts: qcom: msm8916: Add smsm and smp2p nodes") Cc: stable@vger.kernel.org Reported-by: Ramon Fried <rfried@codeaurora.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason, the implementation of some 16-bit ID system calls
(namely, setuid16/setgid16 and setfsuid16/setfsgid16) used type cast
instead of low2highgid/low2highuid macros for converting [GU]IDs, which
led to incorrect handling of value of -1 (which ought to be considered
invalid).
We need to set shared_count even if we already have a fence to wait for.
v2: init i to -1 as well
Signed-off-by: Christian König <christian.koenig@amd.com> Cc: stable@vger.kernel.org Tested-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180122200003.6665-1-christian.koenig@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 398a719d34a1 ("powerpc/mm: Update bits used to skip hash_page")
mistakenly dropped the DSISR_DABRMATCH bit from the mask of bit tested
to skip trying to hash a page.
As a result, the DABR matches would no longer be detected.
This adds it back. We open code it in the 2 places where it matters
rather than fold it into DSISR_BAD_FAULT_32S/64S because this isn't
technically a bad fault and while we would never hit it with the
current code, I prefer if page_fault_is_bad() didn't trigger on these.
Fixes: 398a719d34a1 ("powerpc/mm: Update bits used to skip hash_page") Cc: stable@vger.kernel.org # v4.14 Tested-by: Pedro Miraglia Franco de Carvalho <pedromfc@br.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPU event notification queues on sPAPR should be configured using
a hardware CPU identifier.
The problem did not show up on the Power Hypervisor because pHyp
supports 8 threads per core which keeps CPU number contiguous. This is
not the case on all sPAPR virtual machines, some use SMT=1.
Also improve error logging by adding the CPU number.
Fixes: eac1e731b59e ("powerpc/xive: guest exploitation of the XIVE interrupt controller") Cc: stable@vger.kernel.org # v4.14+ Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Radix guests do normally invalidate process-scoped translations when a
new pid is allocated but migrated guests do not invalidate these so
migrated guests crash sometime, especially easy to reproduce with
migration happening within first 10 seconds after the guest boot start
on the same machine.
This adds the "Invalidate process-scoped translations" flush to fix
radix guests migration.
Fixes: 2ee13be34b13 ("KVM: PPC: Book3S HV: Update kvmppc_set_arch_compat() for ISA v3.00") Cc: stable@vger.kernel.org # v4.10+ Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Tested-by: Laurent Vivier <lvivier@redhat.com> Tested-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DLPAR removing a CPU, the unmapping of the cpu from a node in
unmap_cpu_from_node() should also invalidate the CPUs entry in the
numa_cpu_lookup_table. There is not a guarantee that on a subsequent
DLPAR add of the CPU the associativity will be the same and thus
could be in a different node. Invalidating the entry in the
numa_cpu_lookup_table causes the associativity to be read from the
device tree at the time of the add.
The current behavior of not invalidating the CPUs entry in the
numa_cpu_lookup_table can result in scenarios where the the topology
layout of CPUs in the partition does not match the device tree
or the topology reported by the HMC.
This bug looks like it was introduced in 2004 in the commit titled
"ppc64: cpu hotplug notifier for numa", which is 6b15e4e87e32 in the
linux-fullhist tree. Hence tag it for all stable releases.
If we can't get inode lock immediately in the function
ocfs2_inode_lock_with_page() when reading a page, we should not return
directly here, since this will lead to a softlockup problem when the
kernel is configured with CONFIG_PREEMPT is not set. The method is to
get a blocking lock and immediately unlock before returning, this can
avoid CPU resource waste due to lots of retries, and benefits fairness
in getting lock among multiple nodes, increase efficiency in case
modifying the same file frequently from multiple nodes.
The softlockup crash (when set /proc/sys/kernel/softlockup_panic to 1)
looks like:
About performance improvement, we can see the testing time is reduced,
and CPU utilization decreases, the detailed data is as follows. I ran
multi_mmap test case in ocfs2-test package in a three nodes cluster.
Before applying this patch:
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
2754 ocfs2te+ 20 0 170248 6980 4856 D 80.73 0.341 0:18.71 multi_mmap
1505 root rt 0 222236 123060 97224 S 2.658 6.015 0:01.44 corosync
5 root 20 0 0 0 0 S 1.329 0.000 0:00.19 kworker/u8:0
95 root 20 0 0 0 0 S 1.329 0.000 0:00.25 kworker/u8:1
2728 root 20 0 0 0 0 S 0.997 0.000 0:00.24 jbd2/sda1-33
2721 root 20 0 0 0 0 S 0.664 0.000 0:00.07 ocfs2dc-3C8CFD4
2750 ocfs2te+ 20 0 142976 4652 3532 S 0.664 0.227 0:00.28 mpirun
Link: http://lkml.kernel.org/r/1514447305-30814-1-git-send-email-ghe@suse.com Fixes: 1cce4df04f37 ("ocfs2: do not lock/unlock() inode DLM lock") Signed-off-by: Gang He <ghe@suse.com> Reviewed-by: Eric Ren <zren@suse.com> Acked-by: alex chen <alex.chen@huawei.com> Acked-by: piaojun <piaojun@huawei.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b014e96d1abb ("PCI: Protect pci_error_handlers->reset_notify()
usage with device_lock()") resolves races between driver reset and
removal, but it introduces some new deadlock problems. If we see a
timeout while we've already started suspending, removing, or shutting
down the driver, we might see:
Unfortunately, mwifiex_pcie_remove() already holds the device lock that
pci_reset_function() is now requesting, and so we see a deadlock.
It's necessary to cancel and synchronize our outstanding work before
tearing down the driver, so we can't have this work wait indefinitely
for the lock.
It's reasonable to only "try" to reset here, since this will mostly
happen for cases where it's already difficult to reset the firmware
anyway (e.g., while we're suspending or powering off the system). And if
reset *really* needs to happen, we can always try again later.
Fixes: b014e96d1abb ("PCI: Protect pci_error_handlers->reset_notify() usage with device_lock()") Cc: <stable@vger.kernel.org> Cc: Xinming Hu <huxm@marvell.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Propagate the error of devfreq_add_device() in devm_devfreq_add_device()
rather than statically returning ENOMEM. This makes it slightly faster
to pinpoint the cause of a returned error.
Fixes: 8cd84092d35e ("PM / devfreq: Add resource-managed function for devfreq device") Cc: stable@vger.kernel.org Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TTM tries to allocate coherent memory in chunks of 2MB first to improve
TLB efficiency and falls back to allocating 4K pages if that fails.
Suppress the warning when the 2MB allocations fails since there is a
valid fall back path.
Signed-off-by: Christian König <christian.koenig@amd.com> Reported-by: Mike Galbraith <efault@gmx.de> Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=104082 Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some OpenPOWER boxes can have same pstate values for nominal and
pmin pstates. In these boxes the current code will not initialize
'powernv_pstate_info.min' variable and result in erroneous CPU
frequency reporting. This patch fixes this problem.
Fixes: 09ca4c9b5958 (cpufreq: powernv: Replacing pstate_id with frequency table index) Reported-by: Alvin Wang <wangat@tw.ibm.com> Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: 4.8+ <stable@vger.kernel.org> # 4.8+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rxe driver works as follows:
* The send queue, receive queue and completion queues are implemented as
circular buffers.
* ib_post_send() and ib_post_recv() calls are serialized through a spinlock.
* Removing elements from various queues happens from tasklet
context. Tasklets are guaranteed to run on at most one CPU. This serializes
access to these queues. See also rxe_completer(), rxe_requester() and
rxe_responder().
* rxe_completer() processes the skbs queued onto qp->resp_pkts.
* rxe_requester() handles the send queue (qp->sq.queue).
* rxe_responder() processes the skbs queued onto qp->req_pkts.
Since rxe_drain_req_pkts() processes qp->req_pkts, calling
rxe_drain_req_pkts() from rxe_requester() is racy. Hence this patch.
Reported-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: stable@vger.kernel.org Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following sequence:
* Change queue pair state into IB_QPS_ERR.
* Post a work request on the queue pair.
Triggers the following race condition in the rdma_rxe driver:
* rxe_qp_error() triggers an asynchronous call of rxe_completer(), the function
that examines the QP send queue.
* rxe_post_send() posts a work request on the QP send queue.
If rxe_completer() runs prior to rxe_post_send(), it will drain the send
queue and the driver will assume no further action is necessary.
However, once we post the send to the send queue, because the queue is
in error, no send completion will ever happen and the send will get
stuck. In order to process the send, we need to make sure that
rxe_completer() gets run after a send is posted to a queue pair in an
error state. This patch ensures that happens.
Running the compaction_test sometimes results in out-of-memory
failures. When I debugged this, it turned out that the code to
reset the number of hugepages to the initial value is simply
broken since we write into an open sysctl file descriptor
multiple times without seeking back to the start.
aarch64-linux-gnu-gcc -Wl,-no-as-needed -Wall
-lpthread seccomp_bpf.c -o seccomp_bpf
seccomp_bpf.c: In function 'tracer_ptrace':
seccomp_bpf.c:1720:12: error: '__NR_open' undeclared
(first use in this function)
if (nr == __NR_open)
^~~~~~~~~
seccomp_bpf.c:1720:12: note: each undeclared identifier is reported
only once for each function it appears in
In file included from seccomp_bpf.c:48:0:
seccomp_bpf.c: In function 'TRACE_syscall_ptrace_syscall_dropped':
seccomp_bpf.c:1795:39: error: '__NR_open' undeclared
(first use in this function)
EXPECT_SYSCALL_RETURN(EPERM, syscall(__NR_open));
^
open(2) is a legacy syscall, replaced with openat(2) since 2.6.16.
Thus new architectures in the kernel, such as arm64, don't implement
these legacy syscalls.
The ev_file is an optional parameter for CQ creation. If the parameter
is not passed, the ev_file pointer will be NULL. Using that pointer
to set the cq_context will result in an OOPs.
Verify that ev_file is not NULL before using.
Cc: <stable@vger.kernel.org> # 4.14.x Fixes: 9ee79fce3642 ("IB/core: Add completion queue (cq) object actions") Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change of slid from u16 to u32 results in sizeof(struct ib_wc)
cross 64B boundary, which causes more cache misses. This patch
rearranges the fields and remain the size to 64B.
Allocating steerable UD QPs depends on having at least one IB port,
while releasing those QPs does not.
As a result, when there are only ETH ports, the IB (RoCE) driver
requests releasing a qp range whose base qp is zero, with
qp count zero.
When SR-IOV is enabled, and the VF driver is running on a VM over
a hypervisor which treats such qp release calls as errors
(rather than NOPs), we see lines in the VM message log like:
mlx4_core 0002:00:02.0: Failed to release qp range base:0 cnt:0
Fix this by adding a check for a zero count in mlx4_release_qp_range()
(which thus treats releasing 0 qps as a nop), and eliminating the
check for device managed flow steering when releasing steerable UD QPs.
(Freeing ib_uc_qpns_bitmap unconditionally is also OK, since it
remains NULL when steerable UD QPs are not allocated).
Fixes: 4196670be786 ("IB/mlx4: Don't allocate range of steerable UD QPs for Ethernet-only device") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The request builder was using the incorrect inlines to
build the request header resulting in incorrect data
in the atomic header.
Fix by using the appropriate inlines to create the request.
Fixes: 261a4351844b ("IB/qib,IB/hfi: Use core common header file") Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ib_write_umad() is protected by taking the umad file mutex.
However, it accesses file->port->ib_dev -- which is protected only by the
port's mutex (field file_mutex).
The ib_umad_remove_one() calls ib_umad_kill_port() which sets
port->ib_dev to NULL under the port mutex (NOT the file mutex).
It then sets the mad agent to "dead" under the umad file mutex.
This is a race condition -- because there is a window where
port->ib_dev is NULL, while the agent is not "dead".
I regularly get 50 MB - 60 MB files during kernel randconfig builds.
These large files mostly contain (many repeats of; e.g., 124,594):
In file included from ../include/linux/string.h:6:0,
from ../include/linux/uuid.h:20,
from ../include/linux/mod_devicetable.h:13,
from ../scripts/mod/devicetable-offsets.c:3:
../include/linux/compiler.h:64:4: warning: '______f' is static but declared in inline function 'strcpy' which is not static [enabled by default]
______f = { \
^
../include/linux/compiler.h:56:23: note: in expansion of macro '__trace_if'
^
../include/linux/string.h:425:2: note: in expansion of macro 'if'
if (p_size == (size_t)-1 && q_size == (size_t)-1)
^
This only happens when CONFIG_FORTIFY_SOURCE=y and
CONFIG_PROFILE_ALL_BRANCHES=y, so prevent PROFILE_ALL_BRANCHES if
FORTIFY_SOURCE=y.
In the event of a command failure, cxlflash returns the failure to the upper
layers to process. After processing the error, when the command is queued
again, the private command structure will not be zeroed and the ioasc could be
stale. Per the SISLite specification, the AFU only sets the ioasc in the
presence of a failure. Thus, even though the original command succeeds the
second time, the command is considered a failure due to stale ioasc. This
cycle repeats indefinitely and can cause a hang or IO failure.
To fix the issue, clear the ioasc before queuing any command.
[mkp: added Cc: stable per request]
Fixes: 479ad8e9d48c ("scsi: cxlflash: Remove zeroing of private command data") Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In test cases where an instance of the driver is detached and
reattached, the driver will crash on reattachment. There is a compound
if statement that will skip over the bar setup if the pci_resource_start
call is not successful. The driver erroneously returns success to its
bar setup in this scenario even though the bars aren't properly
configured.
Rework the offending code segment for proper initialization steps. If
the pci_resource_start call fails, -ENOMEM is now returned.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit therefore adds EXPORT_SYMBOL_GPL() for each to allow them to
be used by GPL-licensed kernel modules.
Reported-by: Bart Van Assche <Bart.VanAssche@wdc.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If scsi_eh_scmd_add() is called concurrently with
scsi_host_queue_ready() while shost->host_blocked > 0 then it can
happen that neither function wakes up the SCSI error handler. Fix
this by making every function that decreases the host_busy counter
wake up the error handler if necessary and by protecting the
host_failed checks with the SCSI host lock.
Reported-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
References: https://marc.info/?l=linux-kernel&m=150461610630736 Fixes: commit 746650160866 ("scsi: convert host_busy to atomic_t") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Reviewed-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com> Cc: Konstantin Khorenko <khorenko@virtuozzo.com> Cc: Stuart Hayes <stuart.w.hayes@gmail.com> Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__unregister_ftrace_function_probe() will incorrectly parse the glob filter
because it resets the search variable that was setup by filter_parse_regex().
Al Viro reported this:
After that call of filter_parse_regex() we could have func_g.search not
equal to glob only if glob started with '!' or '*'. In the former case
we would've buggered off with -EINVAL (not = 1). In the latter we
would've set func_g.search equal to glob + 1, calculated the length of
that thing in func_g.len and proceeded to reset func_g.search back to
glob.
Suppose the glob is e.g. *foo*. We end up with
func_g.type = MATCH_MIDDLE_ONLY;
func_g.len = 3;
func_g.search = "*foo";
Feeding that to ftrace_match_record() will not do anything sane - we
will be looking for names containing "*foo" (->len is ignored for that
one).
Setting si_code to 0 is the same a setting si_code to SI_USER which is definitely
not correct. With si_code set to SI_USER si_pid and si_uid will be copied to
userspace instead of si_addr. Which is very wrong.
So fix this by using a sensible si_code (SEGV_MAPERR) for this failure.
Fixes: b920de1b77b7 ("mn10300: add the MN10300/AM33 architecture to the kernel") Cc: David Howells <dhowells@redhat.com> Cc: Masakazu Urade <urade.masakazu@jp.panasonic.com> Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a writable mount, it is not expected for overlayfs to return
EINVAL/EROFS for fsync, even if dir/file is not changed.
This commit fixes the case of fsync of directory, which is easier to
address, because overlayfs already implements fsync file operation for
directories.
The problem reported by Raphael is that new PostgreSQL 10.0 with a
database in overlayfs where lower layer in squashfs fails to start.
The failure is due to fsync error, when PostgreSQL does fsync on all
existing db directories on startup and a specific directory exists
lower layer with no changes.
A NULL pointer reference kernel bug was observed when
acpi_nfit_add_dimm() called in acpi_nfit_register_dimms() failed. This
error path does not set nfit_mem->nvdimm, but the 2nd
list_for_each_entry() loop in the function assumes it's always set. Add
a check to nfit_mem->nvdimm.
Fixes: ba9c8dd3c222 ("acpi, nfit: add dimm device notification support") Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to be printing a raw kernel pointer to the kernel log at
every boot. So just remove it, and change the whole message to use the
correct dev_info() call at the same time.
Reported-by: Wang Qize <wang_qize@venustech.com.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We store a SW state of the t11_t12 timing in 100usec units but have to
program it in 100msec as required by HW. The rounding used during
programming means there will be a mismatch between the SW and HW states
of this value triggering a "PPS state mismatch" error. Avoid this by
storing the already rounded-up value in the SW state.
Note that we still calculate panel_power_cycle_delay with the finer
100usec granularity to avoid any needless waits using that version of
the delay.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103903 Cc: joks <joks@linux.pl> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171129175137.2889-1-imre.deak@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds Ethernet aliases in the Marvell Armada 7040 DB, 8040 DB
and 8040 mcbin device trees so that the bootloader setup the MAC
addresses correctly.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small fixes] Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus reported that GCC-7.3 generated a switch-table construct that
confused objtool. It turns out that, in particular due to KASAN, it is
possible to have unrelated .rodata usage in between the .rodata setup
for the switch-table and the following indirect jump.
The simple linear reverse search from the indirect jump would hit upon
the KASAN .rodata usage first and fail to find a switch_table,
resulting in a spurious 'sibling call with modified stack frame'
warning.
Fix this by creating a 'jump-stack' which we can 'unwind' during
reversal, thereby skipping over much of the in-between code.
This is not fool proof by any means, but is sufficient to make the
known cases work. Future work would be to construct more comprehensive
flow analysis code.
This function was introduced by 247e743cbe6e ("Btrfs: Use async helpers
to deal with pages that have been improperly dirtied") and it didn't do
any error handling then. This function might very well fail in ENOMEM
situation, yet it's not handled, this could lead to inconsistent state.
So let's handle the failure by setting the mapping error bit.
Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arch/x86/kernel/head64.o: In function `sanitize_boot_params':
arch/x86/include/asm/bootparam_utils.h:37: undefined reference to `__ubsan_handle_type_mismatch_v1'
because Clang and GCC 8 slightly changed ABI for 'type mismatch' errors.
Compiler now uses new __ubsan_handle_type_mismatch_v1() function with
slightly modified 'struct type_mismatch_data'.
Let's add new 'struct type_mismatch_data_common' which is independent from
compiler's layout of 'struct type_mismatch_data'. And make
__ubsan_handle_type_mismatch[_v1]() functions transform compiler-dependent
type mismatch data to our internal representation. This way, we can
support both old and new compilers with minimal amount of change.
- The global variable 'clock_event_ddata' is overwritten each time the
init function is invoked.
This is fixed with a kmemdup() instead of assigning the global variable. That
prevents a memory corruption when several timers are defined in the DT.
- The clockevent's event_handler is NULL if the time framework does
not select the clockevent when registering it, this is fine but the init
code generates in any case an interrupt leading to dereference this
NULL pointer.
The stm32 timer works with shadow registers, a mechanism to cache the
registers. When a change is done in one buffered register, we need to
artificially generate an event to force the timer to copy the content
of the register to the shadowed register.
The auto-reload register (ARR) is one of the shadowed register as well as
the prescaler register (PSC), so in order to force the copy, we issue an
event which in turn leads to an interrupt and the NULL dereference.
This is fixed by inverting two lines where we clear the status register
before enabling the update event interrupt.
As this kernel crash is resulting from the combination of these two bugs,
the fixes are grouped into a single patch.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1515418139-23276-11-git-send-email-daniel.lezcano@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After queue is frozen, dispatch still may happen, for example:
1) requests are submitted from several contexts
2) requests from all these contexts are inserted to queue, but may dispatch
to LLD in one of these paths, but other paths sill need to move on even all
these requests are completed(that means blk_mq_freeze_queue_wait() returns
at that time)
3) dispatch after queue freezing still moves on and causes use-after-free,
because request queue is freed
This patch quiesces queue after it is frozen, and makes sure all
in-progress dispatch are completed.
This patch fixes the following kernel crash when running heavy IOs vs.
deleting device:
Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call bdev_get_queue(bdev) after bdev->bd_disk has been initialized
instead of just before that pointer has been initialized. This patch
avoids that the following command
pktsetup 1 /dev/sr0
triggers the following kernel crash:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000548
IP: pkt_setup_dev+0x2db/0x670 [pktcdvd]
CPU: 2 PID: 724 Comm: pktsetup Not tainted 4.15.0-rc4-dbg+ #1
Call Trace:
pkt_ctl_ioctl+0xce/0x1c0 [pktcdvd]
do_vfs_ioctl+0x8e/0x670
SyS_ioctl+0x3c/0x70
entry_SYSCALL_64_fastpath+0x23/0x9a
Reported-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Fixes: commit ca18d6f769d2 ("block: Make most scsi_req_init() calls implicit") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Cc: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 523e1d399ce0 ("block: make gendisk hold a reference to its queue")
modified add_disk() and disk_release() but did not update any of the
error paths that trigger a put_disk() call after disk->queue has been
assigned. That introduced the following behavior in the pktcdvd driver
if pkt_new_dev() fails:
Since disk_release() calls blk_put_queue() anyway if disk->queue != NULL,
fix this by removing the blk_cleanup_queue() call from the pkt_setup_dev()
error path.
Fixes: commit 523e1d399ce0 ("block: make gendisk hold a reference to its queue") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Tejun Heo <tj@kernel.org> Cc: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without such a range, gpiolib fails with -EPROBE_DEFER, pending the
addition of the range. So, without a range, gpiolib will keep
deferring indefinitely.
When using mcp23s08 module with gpio-keys, often (50% of boots)
it fails to get irq numbers with message:
"gpio-keys keys: Unable to get irq number for GPIO 0, error -6".
Seems that irqs must be setup before devm_gpiochip_add_data().
When a GPIO is requested using gpiod_get_* APIs the intel pinctrl driver
switches the pin to GPIO mode and makes sure interrupts are routed to
the GPIO hardware instead of IOAPIC. However, if the GPIO is used
directly through irqchip, as is the case with many I2C-HID devices where
I2C core automatically configures interrupt for the device, the pin is
not initialized as GPIO. Instead we rely that the BIOS configures the
pin accordingly which seems not to be the case at least in Asus X540NA
SKU3 with Focaltech touchpad.
When the pin is not properly configured it might result weird behaviour
like interrupts suddenly stop firing completely and the touchpad stops
responding to user input.
Fix this by properly initializing the pin to GPIO mode also when it is
used directly through irqchip.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support") Reported-by: Daniel Drake <drake@endlessm.com> Reported-and-tested-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix an uninitialized variable warning in the Octeon EDAC driver, as seen
in MIPS cavium_octeon_defconfig builds since v4.14 with Codescape GNU
Tools 2016.05-03:
drivers/edac/octeon_edac-lmc.c In function ‘octeon_lmc_edac_poll_o2’:
drivers/edac/octeon_edac-lmc.c:87:24: warning: ‘((long unsigned int*)&int_reg)[1]’ may \
be used uninitialized in this function [-Wmaybe-uninitialized]
if (int_reg.s.sec_err || int_reg.s.ded_err) {
^
Iinitialise the whole int_reg variable to zero before the conditional
assignments in the error injection case.
Return 0 if the operation was successful, not the userspace memory
value. Check that userspace value equals passed oldval, not itself.
Don't update *uval if the value wasn't read from userspace memory.
This fixes process hang due to infinite loop in futex_lock_pi.
It also fixes a bunch of glibc tests nptl/tst-mutexpi*.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since version 4.9, the kernel automatically breaks printk calls into
multiple newlines unless pr_cont is used. Fix the alpha stacktrace code,
so that it prints stack trace in four columns, as it was initially
intended.
Fix the typo (mixed up arguments) in the EXC macro in the futex
definitions introduced by commit ca282f697381 (alpha: add a
helper for emitting exception table entries).
Signed-off-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a typo in the new version of put_tv32() that caused an unguarded
access of a user space pointer, and failed to return the correct result in
gettimeofday(), wait4(), usleep_thread() and old_adjtimex().
This fixes it to give the correct behavior again.
Fixes: 1cc6c4635e9f ("osf_sys.c: switch handling of timeval32/itimerval32 to copy_{to,from}_user()") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On alpha, a process will crash if it attempts to start a thread and a
signal is delivered at the same time. The crash can be reproduced with
this program: https://cygwin.com/ml/cygwin/2014-11/msg00473.html
The reason for the crash is this:
* we call the clone syscall
* we go to the function copy_process
* copy process calls copy_thread_tls, it is a wrapper around copy_thread
* copy_thread sets the tls pointer: childti->pcb.unique = regs->r20
* copy_thread sets regs->r20 to zero
* we go back to copy_process
* copy process checks "if (signal_pending(current))" and returns
-ERESTARTNOINTR
* the clone syscall is restarted, but this time, regs->r20 is zero, so
the new thread is created with zero tls pointer
* the new thread crashes in start_thread when attempting to access tls
The comment in the code says that setting the register r20 is some
compatibility with OSF/1. But OSF/1 doesn't use the CLONE_SETTLS flag, so
we don't have to zero r20 if CLONE_SETTLS is set. This patch fixes the bug
by zeroing regs->r20 only if CLONE_SETTLS is not set.
projects / people / arne_f / kernel.git / log
